\n
address_offset : 0x0 Bytes (0x0)
size : 0x3C byte (0x0)
mem_usage : registers
protection : not protected
Control A
address_offset : 0x0 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
SWRST : Software Reset
bits : 0 - 0 (1 bit)
ENABLE : Enable
bits : 1 - 1 (1 bit)
CKSEL : Clock Selection
bits : 4 - 4 (1 bit)
Enumeration: CKSELSelect
0 : CLK_GCLK
Clocked by GCLK
1 : CLK_ULP32K
Clocked by ULP32K
End of enumeration elements list.
Non-Maskable Interrupt Control
address_offset : 0x1 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
NMISENSE : Non-Maskable Interrupt Sense Configuration
bits : 0 - 2 (3 bit)
Enumeration: NMISENSESelect
0 : NONE
No detection
1 : RISE
Rising-edge detection
2 : FALL
Falling-edge detection
3 : BOTH
Both-edges detection
4 : HIGH
High-level detection
5 : LOW
Low-level detection
End of enumeration elements list.
NMIFILTEN : Non-Maskable Interrupt Filter Enable
bits : 3 - 3 (1 bit)
NMIASYNCH : Asynchronous Edge Detection Mode
bits : 4 - 4 (1 bit)
Enumeration: NMIASYNCHSelect
0 : SYNC
Edge detection is clock synchronously operated
1 : ASYNC
Edge detection is clock asynchronously operated
End of enumeration elements list.
Interrupt Enable Set
address_offset : 0x10 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXTINT : External Interrupt Enable
bits : 0 - 15 (16 bit)
Interrupt Flag Status and Clear
address_offset : 0x14 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXTINT : External Interrupt
bits : 0 - 15 (16 bit)
External Interrupt Asynchronous Mode
address_offset : 0x18 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
ASYNCH : Asynchronous Edge Detection Mode
bits : 0 - 15 (16 bit)
Enumeration: ASYNCHSelect
0 : SYNC
Edge detection is clock synchronously operated
1 : ASYNC
Edge detection is clock asynchronously operated
End of enumeration elements list.
External Interrupt Sense Configuration
address_offset : 0x1C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
SENSE0 : Input Sense Configuration 0
bits : 0 - 2 (3 bit)
Enumeration: SENSE0Select
0 : NONE
No detection
1 : RISE
Rising edge detection
2 : FALL
Falling edge detection
3 : BOTH
Both edges detection
4 : HIGH
High level detection
5 : LOW
Low level detection
End of enumeration elements list.
FILTEN0 : Filter Enable 0
bits : 3 - 3 (1 bit)
SENSE1 : Input Sense Configuration 1
bits : 4 - 6 (3 bit)
Enumeration: SENSE1Select
0 : NONE
No detection
1 : RISE
Rising edge detection
2 : FALL
Falling edge detection
3 : BOTH
Both edges detection
4 : HIGH
High level detection
5 : LOW
Low level detection
End of enumeration elements list.
FILTEN1 : Filter Enable 1
bits : 7 - 7 (1 bit)
SENSE2 : Input Sense Configuration 2
bits : 8 - 10 (3 bit)
Enumeration: SENSE2Select
0 : NONE
No detection
1 : RISE
Rising edge detection
2 : FALL
Falling edge detection
3 : BOTH
Both edges detection
4 : HIGH
High level detection
5 : LOW
Low level detection
End of enumeration elements list.
FILTEN2 : Filter Enable 2
bits : 11 - 11 (1 bit)
SENSE3 : Input Sense Configuration 3
bits : 12 - 14 (3 bit)
Enumeration: SENSE3Select
0 : NONE
No detection
1 : RISE
Rising edge detection
2 : FALL
Falling edge detection
3 : BOTH
Both edges detection
4 : HIGH
High level detection
5 : LOW
Low level detection
End of enumeration elements list.
FILTEN3 : Filter Enable 3
bits : 15 - 15 (1 bit)
SENSE4 : Input Sense Configuration 4
bits : 16 - 18 (3 bit)
Enumeration: SENSE4Select
0 : NONE
No detection
1 : RISE
Rising edge detection
2 : FALL
Falling edge detection
3 : BOTH
Both edges detection
4 : HIGH
High level detection
5 : LOW
Low level detection
End of enumeration elements list.
FILTEN4 : Filter Enable 4
bits : 19 - 19 (1 bit)
SENSE5 : Input Sense Configuration 5
bits : 20 - 22 (3 bit)
Enumeration: SENSE5Select
0 : NONE
No detection
1 : RISE
Rising edge detection
2 : FALL
Falling edge detection
3 : BOTH
Both edges detection
4 : HIGH
High level detection
5 : LOW
Low level detection
End of enumeration elements list.
FILTEN5 : Filter Enable 5
bits : 23 - 23 (1 bit)
SENSE6 : Input Sense Configuration 6
bits : 24 - 26 (3 bit)
Enumeration: SENSE6Select
0 : NONE
No detection
1 : RISE
Rising edge detection
2 : FALL
Falling edge detection
3 : BOTH
Both edges detection
4 : HIGH
High level detection
5 : LOW
Low level detection
End of enumeration elements list.
FILTEN6 : Filter Enable 6
bits : 27 - 27 (1 bit)
SENSE7 : Input Sense Configuration 7
bits : 28 - 30 (3 bit)
Enumeration: SENSE7Select
0 : NONE
No detection
1 : RISE
Rising edge detection
2 : FALL
Falling edge detection
3 : BOTH
Both edges detection
4 : HIGH
High level detection
5 : LOW
Low level detection
End of enumeration elements list.
FILTEN7 : Filter Enable 7
bits : 31 - 31 (1 bit)
Non-Maskable Interrupt Flag Status and Clear
address_offset : 0x2 Bytes (0x0)
size : 16 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
NMI : Non-Maskable Interrupt
bits : 0 - 0 (1 bit)
External Interrupt Sense Configuration
address_offset : 0x20 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
SENSE0 : Input Sense Configuration 0
bits : 0 - 2 (3 bit)
Enumeration: SENSE0Select
0 : NONE
No detection
1 : RISE
Rising edge detection
2 : FALL
Falling edge detection
3 : BOTH
Both edges detection
4 : HIGH
High level detection
5 : LOW
Low level detection
End of enumeration elements list.
FILTEN0 : Filter Enable 0
bits : 3 - 3 (1 bit)
SENSE1 : Input Sense Configuration 1
bits : 4 - 6 (3 bit)
Enumeration: SENSE1Select
0 : NONE
No detection
1 : RISE
Rising edge detection
2 : FALL
Falling edge detection
3 : BOTH
Both edges detection
4 : HIGH
High level detection
5 : LOW
Low level detection
End of enumeration elements list.
FILTEN1 : Filter Enable 1
bits : 7 - 7 (1 bit)
SENSE2 : Input Sense Configuration 2
bits : 8 - 10 (3 bit)
Enumeration: SENSE2Select
0 : NONE
No detection
1 : RISE
Rising edge detection
2 : FALL
Falling edge detection
3 : BOTH
Both edges detection
4 : HIGH
High level detection
5 : LOW
Low level detection
End of enumeration elements list.
FILTEN2 : Filter Enable 2
bits : 11 - 11 (1 bit)
SENSE3 : Input Sense Configuration 3
bits : 12 - 14 (3 bit)
Enumeration: SENSE3Select
0 : NONE
No detection
1 : RISE
Rising edge detection
2 : FALL
Falling edge detection
3 : BOTH
Both edges detection
4 : HIGH
High level detection
5 : LOW
Low level detection
End of enumeration elements list.
FILTEN3 : Filter Enable 3
bits : 15 - 15 (1 bit)
SENSE4 : Input Sense Configuration 4
bits : 16 - 18 (3 bit)
Enumeration: SENSE4Select
0 : NONE
No detection
1 : RISE
Rising edge detection
2 : FALL
Falling edge detection
3 : BOTH
Both edges detection
4 : HIGH
High level detection
5 : LOW
Low level detection
End of enumeration elements list.
FILTEN4 : Filter Enable 4
bits : 19 - 19 (1 bit)
SENSE5 : Input Sense Configuration 5
bits : 20 - 22 (3 bit)
Enumeration: SENSE5Select
0 : NONE
No detection
1 : RISE
Rising edge detection
2 : FALL
Falling edge detection
3 : BOTH
Both edges detection
4 : HIGH
High level detection
5 : LOW
Low level detection
End of enumeration elements list.
FILTEN5 : Filter Enable 5
bits : 23 - 23 (1 bit)
SENSE6 : Input Sense Configuration 6
bits : 24 - 26 (3 bit)
Enumeration: SENSE6Select
0 : NONE
No detection
1 : RISE
Rising edge detection
2 : FALL
Falling edge detection
3 : BOTH
Both edges detection
4 : HIGH
High level detection
5 : LOW
Low level detection
End of enumeration elements list.
FILTEN6 : Filter Enable 6
bits : 27 - 27 (1 bit)
SENSE7 : Input Sense Configuration 7
bits : 28 - 30 (3 bit)
Enumeration: SENSE7Select
0 : NONE
No detection
1 : RISE
Rising edge detection
2 : FALL
Falling edge detection
3 : BOTH
Both edges detection
4 : HIGH
High level detection
5 : LOW
Low level detection
End of enumeration elements list.
FILTEN7 : Filter Enable 7
bits : 31 - 31 (1 bit)
Debouncer Enable
address_offset : 0x30 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DEBOUNCEN : Debouncer Enable
bits : 0 - 15 (16 bit)
Debouncer Prescaler
address_offset : 0x34 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PRESCALER0 : Debouncer Prescaler
bits : 0 - 2 (3 bit)
Enumeration: PRESCALER0Select
0 : DIV2
EIC clock divided by 2
1 : DIV4
EIC clock divided by 4
2 : DIV8
EIC clock divided by 8
3 : DIV16
EIC clock divided by 16
4 : DIV32
EIC clock divided by 32
5 : DIV64
EIC clock divided by 64
6 : DIV128
EIC clock divided by 128
7 : DIV256
EIC clock divided by 256
End of enumeration elements list.
STATES0 : Debouncer number of states
bits : 3 - 3 (1 bit)
Enumeration: STATES0Select
0 : LFREQ3
3 low frequency samples
1 : LFREQ7
7 low frequency samples
End of enumeration elements list.
PRESCALER1 : Debouncer Prescaler
bits : 4 - 6 (3 bit)
Enumeration: PRESCALER1Select
0 : DIV2
EIC clock divided by 2
1 : DIV4
EIC clock divided by 4
2 : DIV8
EIC clock divided by 8
3 : DIV16
EIC clock divided by 16
4 : DIV32
EIC clock divided by 32
5 : DIV64
EIC clock divided by 64
6 : DIV128
EIC clock divided by 128
7 : DIV256
EIC clock divided by 256
End of enumeration elements list.
STATES1 : Debouncer number of states
bits : 7 - 7 (1 bit)
Enumeration: STATES1Select
0 : LFREQ3
3 low frequency samples
1 : LFREQ7
7 low frequency samples
End of enumeration elements list.
TICKON : Pin Sampler frequency selection
bits : 16 - 16 (1 bit)
Enumeration: TICKONSelect
0 : CLK_GCLK_EIC
Clocked by GCLK
1 : CLK_LFREQ
Clocked by Low Frequency Clock
End of enumeration elements list.
External Interrupt Sense Configuration
address_offset : 0x38 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
SENSE0 : Input Sense Configuration 0
bits : 0 - 2 (3 bit)
Enumeration: SENSE0Select
0 : NONE
No detection
1 : RISE
Rising edge detection
2 : FALL
Falling edge detection
3 : BOTH
Both edges detection
4 : HIGH
High level detection
5 : LOW
Low level detection
End of enumeration elements list.
FILTEN0 : Filter Enable 0
bits : 3 - 3 (1 bit)
SENSE1 : Input Sense Configuration 1
bits : 4 - 6 (3 bit)
Enumeration: SENSE1Select
0 : NONE
No detection
1 : RISE
Rising edge detection
2 : FALL
Falling edge detection
3 : BOTH
Both edges detection
4 : HIGH
High level detection
5 : LOW
Low level detection
End of enumeration elements list.
FILTEN1 : Filter Enable 1
bits : 7 - 7 (1 bit)
SENSE2 : Input Sense Configuration 2
bits : 8 - 10 (3 bit)
Enumeration: SENSE2Select
0 : NONE
No detection
1 : RISE
Rising edge detection
2 : FALL
Falling edge detection
3 : BOTH
Both edges detection
4 : HIGH
High level detection
5 : LOW
Low level detection
End of enumeration elements list.
FILTEN2 : Filter Enable 2
bits : 11 - 11 (1 bit)
SENSE3 : Input Sense Configuration 3
bits : 12 - 14 (3 bit)
Enumeration: SENSE3Select
0 : NONE
No detection
1 : RISE
Rising edge detection
2 : FALL
Falling edge detection
3 : BOTH
Both edges detection
4 : HIGH
High level detection
5 : LOW
Low level detection
End of enumeration elements list.
FILTEN3 : Filter Enable 3
bits : 15 - 15 (1 bit)
SENSE4 : Input Sense Configuration 4
bits : 16 - 18 (3 bit)
Enumeration: SENSE4Select
0 : NONE
No detection
1 : RISE
Rising edge detection
2 : FALL
Falling edge detection
3 : BOTH
Both edges detection
4 : HIGH
High level detection
5 : LOW
Low level detection
End of enumeration elements list.
FILTEN4 : Filter Enable 4
bits : 19 - 19 (1 bit)
SENSE5 : Input Sense Configuration 5
bits : 20 - 22 (3 bit)
Enumeration: SENSE5Select
0 : NONE
No detection
1 : RISE
Rising edge detection
2 : FALL
Falling edge detection
3 : BOTH
Both edges detection
4 : HIGH
High level detection
5 : LOW
Low level detection
End of enumeration elements list.
FILTEN5 : Filter Enable 5
bits : 23 - 23 (1 bit)
SENSE6 : Input Sense Configuration 6
bits : 24 - 26 (3 bit)
Enumeration: SENSE6Select
0 : NONE
No detection
1 : RISE
Rising edge detection
2 : FALL
Falling edge detection
3 : BOTH
Both edges detection
4 : HIGH
High level detection
5 : LOW
Low level detection
End of enumeration elements list.
FILTEN6 : Filter Enable 6
bits : 27 - 27 (1 bit)
SENSE7 : Input Sense Configuration 7
bits : 28 - 30 (3 bit)
Enumeration: SENSE7Select
0 : NONE
No detection
1 : RISE
Rising edge detection
2 : FALL
Falling edge detection
3 : BOTH
Both edges detection
4 : HIGH
High level detection
5 : LOW
Low level detection
End of enumeration elements list.
FILTEN7 : Filter Enable 7
bits : 31 - 31 (1 bit)
Pin State
address_offset : 0x38 Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
PINSTATE : Pin State
bits : 0 - 15 (16 bit)
Synchronization Busy
address_offset : 0x4 Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
SWRST : Software Reset Synchronization Busy Status
bits : 0 - 0 (1 bit)
ENABLE : Enable Synchronization Busy Status
bits : 1 - 1 (1 bit)
External Interrupt Sense Configuration
address_offset : 0x58 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
SENSE0 : Input Sense Configuration 0
bits : 0 - 2 (3 bit)
Enumeration: SENSE0Select
0 : NONE
No detection
1 : RISE
Rising edge detection
2 : FALL
Falling edge detection
3 : BOTH
Both edges detection
4 : HIGH
High level detection
5 : LOW
Low level detection
End of enumeration elements list.
FILTEN0 : Filter Enable 0
bits : 3 - 3 (1 bit)
SENSE1 : Input Sense Configuration 1
bits : 4 - 6 (3 bit)
Enumeration: SENSE1Select
0 : NONE
No detection
1 : RISE
Rising edge detection
2 : FALL
Falling edge detection
3 : BOTH
Both edges detection
4 : HIGH
High level detection
5 : LOW
Low level detection
End of enumeration elements list.
FILTEN1 : Filter Enable 1
bits : 7 - 7 (1 bit)
SENSE2 : Input Sense Configuration 2
bits : 8 - 10 (3 bit)
Enumeration: SENSE2Select
0 : NONE
No detection
1 : RISE
Rising edge detection
2 : FALL
Falling edge detection
3 : BOTH
Both edges detection
4 : HIGH
High level detection
5 : LOW
Low level detection
End of enumeration elements list.
FILTEN2 : Filter Enable 2
bits : 11 - 11 (1 bit)
SENSE3 : Input Sense Configuration 3
bits : 12 - 14 (3 bit)
Enumeration: SENSE3Select
0 : NONE
No detection
1 : RISE
Rising edge detection
2 : FALL
Falling edge detection
3 : BOTH
Both edges detection
4 : HIGH
High level detection
5 : LOW
Low level detection
End of enumeration elements list.
FILTEN3 : Filter Enable 3
bits : 15 - 15 (1 bit)
SENSE4 : Input Sense Configuration 4
bits : 16 - 18 (3 bit)
Enumeration: SENSE4Select
0 : NONE
No detection
1 : RISE
Rising edge detection
2 : FALL
Falling edge detection
3 : BOTH
Both edges detection
4 : HIGH
High level detection
5 : LOW
Low level detection
End of enumeration elements list.
FILTEN4 : Filter Enable 4
bits : 19 - 19 (1 bit)
SENSE5 : Input Sense Configuration 5
bits : 20 - 22 (3 bit)
Enumeration: SENSE5Select
0 : NONE
No detection
1 : RISE
Rising edge detection
2 : FALL
Falling edge detection
3 : BOTH
Both edges detection
4 : HIGH
High level detection
5 : LOW
Low level detection
End of enumeration elements list.
FILTEN5 : Filter Enable 5
bits : 23 - 23 (1 bit)
SENSE6 : Input Sense Configuration 6
bits : 24 - 26 (3 bit)
Enumeration: SENSE6Select
0 : NONE
No detection
1 : RISE
Rising edge detection
2 : FALL
Falling edge detection
3 : BOTH
Both edges detection
4 : HIGH
High level detection
5 : LOW
Low level detection
End of enumeration elements list.
FILTEN6 : Filter Enable 6
bits : 27 - 27 (1 bit)
SENSE7 : Input Sense Configuration 7
bits : 28 - 30 (3 bit)
Enumeration: SENSE7Select
0 : NONE
No detection
1 : RISE
Rising edge detection
2 : FALL
Falling edge detection
3 : BOTH
Both edges detection
4 : HIGH
High level detection
5 : LOW
Low level detection
End of enumeration elements list.
FILTEN7 : Filter Enable 7
bits : 31 - 31 (1 bit)
Event Control
address_offset : 0x8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXTINTEO : External Interrupt Event Output Enable
bits : 0 - 15 (16 bit)
Interrupt Enable Clear
address_offset : 0xC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXTINT : External Interrupt Enable
bits : 0 - 15 (16 bit)
Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !
This website is sponsored by Embeetle, an IDE designed from scratch for embedded software developers.