\n

CCL

Peripheral Memory Blocks

address_offset : 0x0 Bytes (0x0)
size : 0x18 byte (0x0)
mem_usage : registers
protection : not protected

Registers

CTRL

LUTCTRL[0]

LUTCTRL2

LUTCTRL3

LUTCTRL[1]

LUTCTRL[2]

SEQCTRL0

LUTCTRL[3]

SEQCTRL1

SEQCTRL[0]

LUTCTRL0

LUTCTRL1

SEQCTRL[1]


CTRL

Control
address_offset : 0x0 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

CTRL CTRL read-write 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 SWRST ENABLE RUNSTDBY

SWRST : Software Reset
bits : 0 - 0 (1 bit)

Enumeration: SWRSTSelect

0 : DISABLE

The peripheral is not reset

1 : ENABLE

The peripheral is reset

End of enumeration elements list.

ENABLE : Enable
bits : 1 - 1 (1 bit)

Enumeration: ENABLESelect

0 : DISABLE

The peripheral is disabled

1 : ENABLE

The peripheral is enabled

End of enumeration elements list.

RUNSTDBY : Run in Standby
bits : 6 - 6 (1 bit)

Enumeration: RUNSTDBYSelect

0 : DISABLE

Generic clock is not required in standby sleep mode

1 : ENABLE

Generic clock is required in standby sleep mode

End of enumeration elements list.


LUTCTRL[0]

LUT Control x
address_offset : 0x10 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

LUTCTRL[0] LUTCTRL[0] read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ENABLE FILTSEL EDGESEL INSEL0 INSEL1 INSEL2 INVEI LUTEI LUTEO TRUTH

ENABLE : LUT Enable
bits : 1 - 1 (1 bit)

Enumeration: ENABLESelect

0 : DISABLE

LUT block is disabled

1 : ENABLE

LUT block is enabled

End of enumeration elements list.

FILTSEL : Filter Selection
bits : 4 - 5 (2 bit)

Enumeration: FILTSELSelect

0 : DISABLE

Filter disabled

1 : SYNCH

Synchronizer enabled

2 : FILTER

Filter enabled

End of enumeration elements list.

EDGESEL : Edge Selection
bits : 7 - 7 (1 bit)

Enumeration: EDGESELSelect

0 : DISABLE

Edge detector is disabled

1 : ENABLE

Edge detector is enabled

End of enumeration elements list.

INSEL0 : Input Selection 0
bits : 8 - 11 (4 bit)

Enumeration: INSEL0Select

0 : MASK

Masked input

1 : FEEDBACK

Feedback input source

2 : LINK

Linked LUT input source

3 : EVENT

Event input source

4 : IO

I/O pin input source

5 : AC

AC input source

6 : TC

TC input source

7 : ALTTC

Alternate TC input source

8 : TCC

TCC input source

9 : SERCOM

SERCOM input source

End of enumeration elements list.

INSEL1 : Input Selection 1
bits : 12 - 15 (4 bit)

Enumeration: INSEL1Select

0 : MASK

Masked input

1 : FEEDBACK

Feedback input source

2 : LINK

Linked LUT input source

3 : EVENT

Event input source

4 : IO

I/O pin input source

5 : AC

AC input source

6 : TC

TC input source

7 : ALTTC

Alternate TC input source

8 : TCC

TCC input source

9 : SERCOM

SERCOM input source

End of enumeration elements list.

INSEL2 : Input Selection 2
bits : 16 - 19 (4 bit)

Enumeration: INSEL2Select

0 : MASK

Masked input

1 : FEEDBACK

Feedback input source

2 : LINK

Linked LUT input source

3 : EVENT

Event input source

4 : IO

I/O pin input source

5 : AC

AC input source

6 : TC

TC input source

7 : ALTTC

Alternate TC input source

8 : TCC

TCC input source

9 : SERCOM

SERCOM input source

End of enumeration elements list.

INVEI : Inverted Event Input Enable
bits : 20 - 20 (1 bit)

Enumeration: INVEISelect

0 : DISABLE

Incoming event is not inverted

1 : ENABLE

Incoming event is inverted

End of enumeration elements list.

LUTEI : LUT Event Input Enable
bits : 21 - 21 (1 bit)

Enumeration: LUTEISelect

0 : DISABLE

LUT incoming event is disabled

1 : ENABLE

LUT incoming event is enabled

End of enumeration elements list.

LUTEO : LUT Event Output Enable
bits : 22 - 22 (1 bit)

Enumeration: LUTEOSelect

0 : DISABLE

LUT event output is disabled

1 : ENABLE

LUT event output is enabled

End of enumeration elements list.

TRUTH : Truth Value
bits : 24 - 31 (8 bit)


LUTCTRL2

LUT Control x
address_offset : 0x10 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

LUTCTRL2 LUTCTRL2 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ENABLE FILTSEL EDGESEL INSEL0 INSEL1 INSEL2 INVEI LUTEI LUTEO TRUTH

ENABLE : LUT Enable
bits : 1 - 1 (1 bit)

Enumeration: ENABLESelect

0 : DISABLE

LUT block is disabled

1 : ENABLE

LUT block is enabled

End of enumeration elements list.

FILTSEL : Filter Selection
bits : 4 - 5 (2 bit)

Enumeration: FILTSELSelect

0 : DISABLE

Filter disabled

1 : SYNCH

Synchronizer enabled

2 : FILTER

Filter enabled

End of enumeration elements list.

EDGESEL : Edge Selection
bits : 7 - 7 (1 bit)

Enumeration: EDGESELSelect

0 : DISABLE

Edge detector is disabled

1 : ENABLE

Edge detector is enabled

End of enumeration elements list.

INSEL0 : Input Selection 0
bits : 8 - 11 (4 bit)

Enumeration: INSEL0Select

0 : MASK

Masked input

1 : FEEDBACK

Feedback input source

2 : LINK

Linked LUT input source

3 : EVENT

Event input source

4 : IO

I/O pin input source

5 : AC

AC input source

6 : TC

TC input source

7 : ALTTC

Alternate TC input source

8 : TCC

TCC input source

9 : SERCOM

SERCOM input source

End of enumeration elements list.

INSEL1 : Input Selection 1
bits : 12 - 15 (4 bit)

Enumeration: INSEL1Select

0 : MASK

Masked input

1 : FEEDBACK

Feedback input source

2 : LINK

Linked LUT input source

3 : EVENT

Event input source

4 : IO

I/O pin input source

5 : AC

AC input source

6 : TC

TC input source

7 : ALTTC

Alternate TC input source

8 : TCC

TCC input source

9 : SERCOM

SERCOM input source

End of enumeration elements list.

INSEL2 : Input Selection 2
bits : 16 - 19 (4 bit)

Enumeration: INSEL2Select

0 : MASK

Masked input

1 : FEEDBACK

Feedback input source

2 : LINK

Linked LUT input source

3 : EVENT

Event input source

4 : IO

I/O pin input source

5 : AC

AC input source

6 : TC

TC input source

7 : ALTTC

Alternate TC input source

8 : TCC

TCC input source

9 : SERCOM

SERCOM input source

End of enumeration elements list.

INVEI : Inverted Event Input Enable
bits : 20 - 20 (1 bit)

Enumeration: INVEISelect

0 : DISABLE

Incoming event is not inverted

1 : ENABLE

Incoming event is inverted

End of enumeration elements list.

LUTEI : LUT Event Input Enable
bits : 21 - 21 (1 bit)

Enumeration: LUTEISelect

0 : DISABLE

LUT incoming event is disabled

1 : ENABLE

LUT incoming event is enabled

End of enumeration elements list.

LUTEO : LUT Event Output Enable
bits : 22 - 22 (1 bit)

Enumeration: LUTEOSelect

0 : DISABLE

LUT event output is disabled

1 : ENABLE

LUT event output is enabled

End of enumeration elements list.

TRUTH : Truth Value
bits : 24 - 31 (8 bit)


LUTCTRL3

LUT Control x
address_offset : 0x14 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

LUTCTRL3 LUTCTRL3 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ENABLE FILTSEL EDGESEL INSEL0 INSEL1 INSEL2 INVEI LUTEI LUTEO TRUTH

ENABLE : LUT Enable
bits : 1 - 1 (1 bit)

Enumeration: ENABLESelect

0 : DISABLE

LUT block is disabled

1 : ENABLE

LUT block is enabled

End of enumeration elements list.

FILTSEL : Filter Selection
bits : 4 - 5 (2 bit)

Enumeration: FILTSELSelect

0 : DISABLE

Filter disabled

1 : SYNCH

Synchronizer enabled

2 : FILTER

Filter enabled

End of enumeration elements list.

EDGESEL : Edge Selection
bits : 7 - 7 (1 bit)

Enumeration: EDGESELSelect

0 : DISABLE

Edge detector is disabled

1 : ENABLE

Edge detector is enabled

End of enumeration elements list.

INSEL0 : Input Selection 0
bits : 8 - 11 (4 bit)

Enumeration: INSEL0Select

0 : MASK

Masked input

1 : FEEDBACK

Feedback input source

2 : LINK

Linked LUT input source

3 : EVENT

Event input source

4 : IO

I/O pin input source

5 : AC

AC input source

6 : TC

TC input source

7 : ALTTC

Alternate TC input source

8 : TCC

TCC input source

9 : SERCOM

SERCOM input source

End of enumeration elements list.

INSEL1 : Input Selection 1
bits : 12 - 15 (4 bit)

Enumeration: INSEL1Select

0 : MASK

Masked input

1 : FEEDBACK

Feedback input source

2 : LINK

Linked LUT input source

3 : EVENT

Event input source

4 : IO

I/O pin input source

5 : AC

AC input source

6 : TC

TC input source

7 : ALTTC

Alternate TC input source

8 : TCC

TCC input source

9 : SERCOM

SERCOM input source

End of enumeration elements list.

INSEL2 : Input Selection 2
bits : 16 - 19 (4 bit)

Enumeration: INSEL2Select

0 : MASK

Masked input

1 : FEEDBACK

Feedback input source

2 : LINK

Linked LUT input source

3 : EVENT

Event input source

4 : IO

I/O pin input source

5 : AC

AC input source

6 : TC

TC input source

7 : ALTTC

Alternate TC input source

8 : TCC

TCC input source

9 : SERCOM

SERCOM input source

End of enumeration elements list.

INVEI : Inverted Event Input Enable
bits : 20 - 20 (1 bit)

Enumeration: INVEISelect

0 : DISABLE

Incoming event is not inverted

1 : ENABLE

Incoming event is inverted

End of enumeration elements list.

LUTEI : LUT Event Input Enable
bits : 21 - 21 (1 bit)

Enumeration: LUTEISelect

0 : DISABLE

LUT incoming event is disabled

1 : ENABLE

LUT incoming event is enabled

End of enumeration elements list.

LUTEO : LUT Event Output Enable
bits : 22 - 22 (1 bit)

Enumeration: LUTEOSelect

0 : DISABLE

LUT event output is disabled

1 : ENABLE

LUT event output is enabled

End of enumeration elements list.

TRUTH : Truth Value
bits : 24 - 31 (8 bit)


LUTCTRL[1]

LUT Control x
address_offset : 0x1C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

LUTCTRL[1] LUTCTRL[1] read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ENABLE FILTSEL EDGESEL INSEL0 INSEL1 INSEL2 INVEI LUTEI LUTEO TRUTH

ENABLE : LUT Enable
bits : 1 - 1 (1 bit)

Enumeration: ENABLESelect

0 : DISABLE

LUT block is disabled

1 : ENABLE

LUT block is enabled

End of enumeration elements list.

FILTSEL : Filter Selection
bits : 4 - 5 (2 bit)

Enumeration: FILTSELSelect

0 : DISABLE

Filter disabled

1 : SYNCH

Synchronizer enabled

2 : FILTER

Filter enabled

End of enumeration elements list.

EDGESEL : Edge Selection
bits : 7 - 7 (1 bit)

Enumeration: EDGESELSelect

0 : DISABLE

Edge detector is disabled

1 : ENABLE

Edge detector is enabled

End of enumeration elements list.

INSEL0 : Input Selection 0
bits : 8 - 11 (4 bit)

Enumeration: INSEL0Select

0 : MASK

Masked input

1 : FEEDBACK

Feedback input source

2 : LINK

Linked LUT input source

3 : EVENT

Event input source

4 : IO

I/O pin input source

5 : AC

AC input source

6 : TC

TC input source

7 : ALTTC

Alternate TC input source

8 : TCC

TCC input source

9 : SERCOM

SERCOM input source

End of enumeration elements list.

INSEL1 : Input Selection 1
bits : 12 - 15 (4 bit)

Enumeration: INSEL1Select

0 : MASK

Masked input

1 : FEEDBACK

Feedback input source

2 : LINK

Linked LUT input source

3 : EVENT

Event input source

4 : IO

I/O pin input source

5 : AC

AC input source

6 : TC

TC input source

7 : ALTTC

Alternate TC input source

8 : TCC

TCC input source

9 : SERCOM

SERCOM input source

End of enumeration elements list.

INSEL2 : Input Selection 2
bits : 16 - 19 (4 bit)

Enumeration: INSEL2Select

0 : MASK

Masked input

1 : FEEDBACK

Feedback input source

2 : LINK

Linked LUT input source

3 : EVENT

Event input source

4 : IO

I/O pin input source

5 : AC

AC input source

6 : TC

TC input source

7 : ALTTC

Alternate TC input source

8 : TCC

TCC input source

9 : SERCOM

SERCOM input source

End of enumeration elements list.

INVEI : Inverted Event Input Enable
bits : 20 - 20 (1 bit)

Enumeration: INVEISelect

0 : DISABLE

Incoming event is not inverted

1 : ENABLE

Incoming event is inverted

End of enumeration elements list.

LUTEI : LUT Event Input Enable
bits : 21 - 21 (1 bit)

Enumeration: LUTEISelect

0 : DISABLE

LUT incoming event is disabled

1 : ENABLE

LUT incoming event is enabled

End of enumeration elements list.

LUTEO : LUT Event Output Enable
bits : 22 - 22 (1 bit)

Enumeration: LUTEOSelect

0 : DISABLE

LUT event output is disabled

1 : ENABLE

LUT event output is enabled

End of enumeration elements list.

TRUTH : Truth Value
bits : 24 - 31 (8 bit)


LUTCTRL[2]

LUT Control x
address_offset : 0x2C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

LUTCTRL[2] LUTCTRL[2] read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ENABLE FILTSEL EDGESEL INSEL0 INSEL1 INSEL2 INVEI LUTEI LUTEO TRUTH

ENABLE : LUT Enable
bits : 1 - 1 (1 bit)

Enumeration: ENABLESelect

0 : DISABLE

LUT block is disabled

1 : ENABLE

LUT block is enabled

End of enumeration elements list.

FILTSEL : Filter Selection
bits : 4 - 5 (2 bit)

Enumeration: FILTSELSelect

0 : DISABLE

Filter disabled

1 : SYNCH

Synchronizer enabled

2 : FILTER

Filter enabled

End of enumeration elements list.

EDGESEL : Edge Selection
bits : 7 - 7 (1 bit)

Enumeration: EDGESELSelect

0 : DISABLE

Edge detector is disabled

1 : ENABLE

Edge detector is enabled

End of enumeration elements list.

INSEL0 : Input Selection 0
bits : 8 - 11 (4 bit)

Enumeration: INSEL0Select

0 : MASK

Masked input

1 : FEEDBACK

Feedback input source

2 : LINK

Linked LUT input source

3 : EVENT

Event input source

4 : IO

I/O pin input source

5 : AC

AC input source

6 : TC

TC input source

7 : ALTTC

Alternate TC input source

8 : TCC

TCC input source

9 : SERCOM

SERCOM input source

End of enumeration elements list.

INSEL1 : Input Selection 1
bits : 12 - 15 (4 bit)

Enumeration: INSEL1Select

0 : MASK

Masked input

1 : FEEDBACK

Feedback input source

2 : LINK

Linked LUT input source

3 : EVENT

Event input source

4 : IO

I/O pin input source

5 : AC

AC input source

6 : TC

TC input source

7 : ALTTC

Alternate TC input source

8 : TCC

TCC input source

9 : SERCOM

SERCOM input source

End of enumeration elements list.

INSEL2 : Input Selection 2
bits : 16 - 19 (4 bit)

Enumeration: INSEL2Select

0 : MASK

Masked input

1 : FEEDBACK

Feedback input source

2 : LINK

Linked LUT input source

3 : EVENT

Event input source

4 : IO

I/O pin input source

5 : AC

AC input source

6 : TC

TC input source

7 : ALTTC

Alternate TC input source

8 : TCC

TCC input source

9 : SERCOM

SERCOM input source

End of enumeration elements list.

INVEI : Inverted Event Input Enable
bits : 20 - 20 (1 bit)

Enumeration: INVEISelect

0 : DISABLE

Incoming event is not inverted

1 : ENABLE

Incoming event is inverted

End of enumeration elements list.

LUTEI : LUT Event Input Enable
bits : 21 - 21 (1 bit)

Enumeration: LUTEISelect

0 : DISABLE

LUT incoming event is disabled

1 : ENABLE

LUT incoming event is enabled

End of enumeration elements list.

LUTEO : LUT Event Output Enable
bits : 22 - 22 (1 bit)

Enumeration: LUTEOSelect

0 : DISABLE

LUT event output is disabled

1 : ENABLE

LUT event output is enabled

End of enumeration elements list.

TRUTH : Truth Value
bits : 24 - 31 (8 bit)


SEQCTRL0

SEQ Control x
address_offset : 0x4 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

SEQCTRL0 SEQCTRL0 read-write 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 SEQSEL

SEQSEL : Sequential Selection
bits : 0 - 3 (4 bit)

Enumeration: SEQSELSelect

0 : DISABLE

Sequential logic is disabled

1 : DFF

D flip flop

2 : JK

JK flip flop

3 : LATCH

D latch

4 : RS

RS latch

End of enumeration elements list.


LUTCTRL[3]

LUT Control x
address_offset : 0x40 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

LUTCTRL[3] LUTCTRL[3] read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ENABLE FILTSEL EDGESEL INSEL0 INSEL1 INSEL2 INVEI LUTEI LUTEO TRUTH

ENABLE : LUT Enable
bits : 1 - 1 (1 bit)

Enumeration: ENABLESelect

0 : DISABLE

LUT block is disabled

1 : ENABLE

LUT block is enabled

End of enumeration elements list.

FILTSEL : Filter Selection
bits : 4 - 5 (2 bit)

Enumeration: FILTSELSelect

0 : DISABLE

Filter disabled

1 : SYNCH

Synchronizer enabled

2 : FILTER

Filter enabled

End of enumeration elements list.

EDGESEL : Edge Selection
bits : 7 - 7 (1 bit)

Enumeration: EDGESELSelect

0 : DISABLE

Edge detector is disabled

1 : ENABLE

Edge detector is enabled

End of enumeration elements list.

INSEL0 : Input Selection 0
bits : 8 - 11 (4 bit)

Enumeration: INSEL0Select

0 : MASK

Masked input

1 : FEEDBACK

Feedback input source

2 : LINK

Linked LUT input source

3 : EVENT

Event input source

4 : IO

I/O pin input source

5 : AC

AC input source

6 : TC

TC input source

7 : ALTTC

Alternate TC input source

8 : TCC

TCC input source

9 : SERCOM

SERCOM input source

End of enumeration elements list.

INSEL1 : Input Selection 1
bits : 12 - 15 (4 bit)

Enumeration: INSEL1Select

0 : MASK

Masked input

1 : FEEDBACK

Feedback input source

2 : LINK

Linked LUT input source

3 : EVENT

Event input source

4 : IO

I/O pin input source

5 : AC

AC input source

6 : TC

TC input source

7 : ALTTC

Alternate TC input source

8 : TCC

TCC input source

9 : SERCOM

SERCOM input source

End of enumeration elements list.

INSEL2 : Input Selection 2
bits : 16 - 19 (4 bit)

Enumeration: INSEL2Select

0 : MASK

Masked input

1 : FEEDBACK

Feedback input source

2 : LINK

Linked LUT input source

3 : EVENT

Event input source

4 : IO

I/O pin input source

5 : AC

AC input source

6 : TC

TC input source

7 : ALTTC

Alternate TC input source

8 : TCC

TCC input source

9 : SERCOM

SERCOM input source

End of enumeration elements list.

INVEI : Inverted Event Input Enable
bits : 20 - 20 (1 bit)

Enumeration: INVEISelect

0 : DISABLE

Incoming event is not inverted

1 : ENABLE

Incoming event is inverted

End of enumeration elements list.

LUTEI : LUT Event Input Enable
bits : 21 - 21 (1 bit)

Enumeration: LUTEISelect

0 : DISABLE

LUT incoming event is disabled

1 : ENABLE

LUT incoming event is enabled

End of enumeration elements list.

LUTEO : LUT Event Output Enable
bits : 22 - 22 (1 bit)

Enumeration: LUTEOSelect

0 : DISABLE

LUT event output is disabled

1 : ENABLE

LUT event output is enabled

End of enumeration elements list.

TRUTH : Truth Value
bits : 24 - 31 (8 bit)


SEQCTRL1

SEQ Control x
address_offset : 0x5 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

SEQCTRL1 SEQCTRL1 read-write 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 SEQSEL

SEQSEL : Sequential Selection
bits : 0 - 3 (4 bit)

Enumeration: SEQSELSelect

0 : DISABLE

Sequential logic is disabled

1 : DFF

D flip flop

2 : JK

JK flip flop

3 : LATCH

D latch

4 : RS

RS latch

End of enumeration elements list.


SEQCTRL[0]

SEQ Control x
address_offset : 0x8 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

SEQCTRL[0] SEQCTRL[0] read-write 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 SEQSEL

SEQSEL : Sequential Selection
bits : 0 - 3 (4 bit)

Enumeration: SEQSELSelect

0 : DISABLE

Sequential logic is disabled

1 : DFF

D flip flop

2 : JK

JK flip flop

3 : LATCH

D latch

4 : RS

RS latch

End of enumeration elements list.


LUTCTRL0

LUT Control x
address_offset : 0x8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

LUTCTRL0 LUTCTRL0 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ENABLE FILTSEL EDGESEL INSEL0 INSEL1 INSEL2 INVEI LUTEI LUTEO TRUTH

ENABLE : LUT Enable
bits : 1 - 1 (1 bit)

Enumeration: ENABLESelect

0 : DISABLE

LUT block is disabled

1 : ENABLE

LUT block is enabled

End of enumeration elements list.

FILTSEL : Filter Selection
bits : 4 - 5 (2 bit)

Enumeration: FILTSELSelect

0 : DISABLE

Filter disabled

1 : SYNCH

Synchronizer enabled

2 : FILTER

Filter enabled

End of enumeration elements list.

EDGESEL : Edge Selection
bits : 7 - 7 (1 bit)

Enumeration: EDGESELSelect

0 : DISABLE

Edge detector is disabled

1 : ENABLE

Edge detector is enabled

End of enumeration elements list.

INSEL0 : Input Selection 0
bits : 8 - 11 (4 bit)

Enumeration: INSEL0Select

0 : MASK

Masked input

1 : FEEDBACK

Feedback input source

2 : LINK

Linked LUT input source

3 : EVENT

Event input source

4 : IO

I/O pin input source

5 : AC

AC input source

6 : TC

TC input source

7 : ALTTC

Alternate TC input source

8 : TCC

TCC input source

9 : SERCOM

SERCOM input source

End of enumeration elements list.

INSEL1 : Input Selection 1
bits : 12 - 15 (4 bit)

Enumeration: INSEL1Select

0 : MASK

Masked input

1 : FEEDBACK

Feedback input source

2 : LINK

Linked LUT input source

3 : EVENT

Event input source

4 : IO

I/O pin input source

5 : AC

AC input source

6 : TC

TC input source

7 : ALTTC

Alternate TC input source

8 : TCC

TCC input source

9 : SERCOM

SERCOM input source

End of enumeration elements list.

INSEL2 : Input Selection 2
bits : 16 - 19 (4 bit)

Enumeration: INSEL2Select

0 : MASK

Masked input

1 : FEEDBACK

Feedback input source

2 : LINK

Linked LUT input source

3 : EVENT

Event input source

4 : IO

I/O pin input source

5 : AC

AC input source

6 : TC

TC input source

7 : ALTTC

Alternate TC input source

8 : TCC

TCC input source

9 : SERCOM

SERCOM input source

End of enumeration elements list.

INVEI : Inverted Event Input Enable
bits : 20 - 20 (1 bit)

Enumeration: INVEISelect

0 : DISABLE

Incoming event is not inverted

1 : ENABLE

Incoming event is inverted

End of enumeration elements list.

LUTEI : LUT Event Input Enable
bits : 21 - 21 (1 bit)

Enumeration: LUTEISelect

0 : DISABLE

LUT incoming event is disabled

1 : ENABLE

LUT incoming event is enabled

End of enumeration elements list.

LUTEO : LUT Event Output Enable
bits : 22 - 22 (1 bit)

Enumeration: LUTEOSelect

0 : DISABLE

LUT event output is disabled

1 : ENABLE

LUT event output is enabled

End of enumeration elements list.

TRUTH : Truth Value
bits : 24 - 31 (8 bit)


LUTCTRL1

LUT Control x
address_offset : 0xC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

LUTCTRL1 LUTCTRL1 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ENABLE FILTSEL EDGESEL INSEL0 INSEL1 INSEL2 INVEI LUTEI LUTEO TRUTH

ENABLE : LUT Enable
bits : 1 - 1 (1 bit)

Enumeration: ENABLESelect

0 : DISABLE

LUT block is disabled

1 : ENABLE

LUT block is enabled

End of enumeration elements list.

FILTSEL : Filter Selection
bits : 4 - 5 (2 bit)

Enumeration: FILTSELSelect

0 : DISABLE

Filter disabled

1 : SYNCH

Synchronizer enabled

2 : FILTER

Filter enabled

End of enumeration elements list.

EDGESEL : Edge Selection
bits : 7 - 7 (1 bit)

Enumeration: EDGESELSelect

0 : DISABLE

Edge detector is disabled

1 : ENABLE

Edge detector is enabled

End of enumeration elements list.

INSEL0 : Input Selection 0
bits : 8 - 11 (4 bit)

Enumeration: INSEL0Select

0 : MASK

Masked input

1 : FEEDBACK

Feedback input source

2 : LINK

Linked LUT input source

3 : EVENT

Event input source

4 : IO

I/O pin input source

5 : AC

AC input source

6 : TC

TC input source

7 : ALTTC

Alternate TC input source

8 : TCC

TCC input source

9 : SERCOM

SERCOM input source

End of enumeration elements list.

INSEL1 : Input Selection 1
bits : 12 - 15 (4 bit)

Enumeration: INSEL1Select

0 : MASK

Masked input

1 : FEEDBACK

Feedback input source

2 : LINK

Linked LUT input source

3 : EVENT

Event input source

4 : IO

I/O pin input source

5 : AC

AC input source

6 : TC

TC input source

7 : ALTTC

Alternate TC input source

8 : TCC

TCC input source

9 : SERCOM

SERCOM input source

End of enumeration elements list.

INSEL2 : Input Selection 2
bits : 16 - 19 (4 bit)

Enumeration: INSEL2Select

0 : MASK

Masked input

1 : FEEDBACK

Feedback input source

2 : LINK

Linked LUT input source

3 : EVENT

Event input source

4 : IO

I/O pin input source

5 : AC

AC input source

6 : TC

TC input source

7 : ALTTC

Alternate TC input source

8 : TCC

TCC input source

9 : SERCOM

SERCOM input source

End of enumeration elements list.

INVEI : Inverted Event Input Enable
bits : 20 - 20 (1 bit)

Enumeration: INVEISelect

0 : DISABLE

Incoming event is not inverted

1 : ENABLE

Incoming event is inverted

End of enumeration elements list.

LUTEI : LUT Event Input Enable
bits : 21 - 21 (1 bit)

Enumeration: LUTEISelect

0 : DISABLE

LUT incoming event is disabled

1 : ENABLE

LUT incoming event is enabled

End of enumeration elements list.

LUTEO : LUT Event Output Enable
bits : 22 - 22 (1 bit)

Enumeration: LUTEOSelect

0 : DISABLE

LUT event output is disabled

1 : ENABLE

LUT event output is enabled

End of enumeration elements list.

TRUTH : Truth Value
bits : 24 - 31 (8 bit)


SEQCTRL[1]

SEQ Control x
address_offset : 0xD Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

SEQCTRL[1] SEQCTRL[1] read-write 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 SEQSEL

SEQSEL : Sequential Selection
bits : 0 - 3 (4 bit)

Enumeration: SEQSELSelect

0 : DISABLE

Sequential logic is disabled

1 : DFF

D flip flop

2 : JK

JK flip flop

3 : LATCH

D latch

4 : RS

RS latch

End of enumeration elements list.



Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !

This website is sponsored by EmbeetleEmbeetle, an IDE designed from scratch for embedded software developers.