Embeetle, an IDE designed from scratch for embedded software developers.address_offset : 0x0 Bytes (0x0)
size : 0x3 byte (0x0)
mem_usage : registers
protection : not protected
Control Register 0
address_offset : 0x0 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MODE : OPAMP Mode Select
bits : 0 - 1 (2 bit)
access : read-write
Enumeration:
#00 : 00
Buffer
#10 : 10
General purpose
#01 : 01
Inverting PGA
#11 : 11
Non-inverting PGA
End of enumeration elements list.
RESERVED : no description available
bits : 2 - 5 (4 bit)
access : read-only
LPEN : Low-Power Mode Enable
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
High-speed mode selected. In this mode, OPAMP has faster slew rate and unity gain bandwidth performance with higher current consumption.
#1 : 1
Low-power mode selected. In this mode, OPAMP has lower current consumption with slower slew rate and unity gain bandwidth performance.
End of enumeration elements list.
EN : OPAMP Enable
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
OPAMP is disabled and not powered
#1 : 1
OPAMP is enabled and powered
End of enumeration elements list.
Control Register 1
address_offset : 0x1 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
AMPRI : Gains Selector
bits : 0 - 1 (2 bit)
access : read-write
AMPRF : Gains Selector
bits : 2 - 4 (3 bit)
access : read-write
RESERVED : no description available
bits : 5 - 7 (3 bit)
access : read-only
Control Register 2
address_offset : 0x2 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
AMPNSEL : Amplifier Negative Input Terminal Selector.
bits : 0 - 2 (3 bit)
access : read-write
Enumeration:
#000 : 000
Negative input 0
#001 : 001
Negative input 1
#010 : 010
Negative input 2
#011 : 011
Negative input 3
#100 : 100
Negative input 4
#101 : 101
Negative input 5
#110 : 110
Negative input 6
#111 : 111
Negative input 7
End of enumeration elements list.
RESERVED : no description available
bits : 3 - 3 (1 bit)
access : read-only
AMPPSEL : Amplifier Positive Input Terminal Selector
bits : 4 - 6 (3 bit)
access : read-write
Enumeration:
#000 : 000
Positive input 0
#001 : 001
Positive input 1
#010 : 010
Positive input 2
#011 : 011
Positive input 3
#100 : 100
Positive input 4
#101 : 101
Positive input 5
#110 : 110
Positive input 6
#111 : 111
Positive input 7
End of enumeration elements list.
RESERVED : no description available
bits : 7 - 7 (1 bit)
access : read-only
Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !
This website is sponsored by Embeetle, an IDE designed from scratch for embedded software developers.