\n
address_offset : 0x0 Bytes (0x0)
size : 0x160 byte (0x0)
mem_usage : registers
protection : not protected
General Control and Status Register
address_offset : 0x0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
STPE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disable TSI when MCU enters low-power modes
#1 : 1
Allow TSI to continue running in all low power modes
End of enumeration elements list.
STM : Scan trigger mode
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Software trigger scan
#1 : 1
Periodical scan
End of enumeration elements list.
ESOR : End-of-scan or out-of-range interrupt select
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
Out-of-range interrupt selected
#1 : 1
End-of-scan interrupt selected
End of enumeration elements list.
ERIE : TSI error interrupt Enable
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
Error interrupt disabled
#1 : 1
Error interrupt enabled
End of enumeration elements list.
TSIIE : TSI interrupt enable
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disable
#1 : 1
Enable
End of enumeration elements list.
TSIEN : TSI module enable
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
TSI disabled
#1 : 1
TSI enabled
End of enumeration elements list.
SWTS : Software trigger start
bits : 8 - 8 (1 bit)
access : write-only
SCNIP : Scan-in-progress status
bits : 9 - 9 (1 bit)
access : read-only
OVRF : Overrun error flag
bits : 12 - 12 (1 bit)
access : read-write
Enumeration:
#0 : 0
No overrun
#1 : 1
Overrun occurred
End of enumeration elements list.
EXTERF : External electrode error occurred
bits : 13 - 13 (1 bit)
access : read-write
Enumeration:
#0 : 0
No short
#1 : 1
Short to VDD or VSS occured on the electrodes
End of enumeration elements list.
OUTRGF : Out of Range Flag
bits : 14 - 14 (1 bit)
access : read-write
EOSF : End of scan flag
bits : 15 - 15 (1 bit)
access : read-write
PS : Electrode oscillator prescaler
bits : 16 - 18 (3 bit)
access : read-write
Enumeration:
#000 : 000
Electrode oscillator frequency divided by 1
#001 : 001
Electrode oscillator frequency divided by 2
#010 : 010
Electrode oscillator frequency divided by 4
#011 : 011
Electrode oscillator frequency divided by 8
#100 : 100
Electrode oscillator frequency divided by 16
#101 : 101
Electrode oscillator frequency divided by 32
#110 : 110
Electrode oscillator frequency divided by 64
#111 : 111
Electrode oscillator frequency divided by 128
End of enumeration elements list.
NSCN : Number of Consecutive Scans per Electrode
bits : 19 - 23 (5 bit)
access : read-write
Enumeration:
#00000 : 00000
1 time per electrode
#00001 : 00001
2 times per electrode
#00010 : 00010
3 times per electrode
#00011 : 00011
4 times per electrode
#00100 : 00100
5 times per electrode
#00101 : 00101
6 times per electrode
#00110 : 00110
7 times per electrode
#00111 : 00111
8 times per electrode
#01000 : 01000
9 times per electrode
#01001 : 01001
10 times per electrode
#01010 : 01010
11 times per electrode
#01011 : 01011
12 times per electrode
#01100 : 01100
13 times per electrode
#01101 : 01101
14 times per electrode
#01110 : 01110
15 times per electrode
#01111 : 01111
16 times per electrode
#10000 : 10000
17 times per electrode
#10001 : 10001
18 times per electrode
#10010 : 10010
19 times per electrode
#10011 : 10011
20 times per electrode
#10100 : 10100
21 times per electrode
#10101 : 10101
22 times per electrode
#10110 : 10110
23 times per electrode
#10111 : 10111
24 times per electrode
#11000 : 11000
25 times per electrode
#11001 : 11001
26 times per electrode
#11010 : 11010
27 times per electrode
#11011 : 11011
28 times per electrode
#11100 : 11100
29 times per electrode
#11101 : 11101
30 times per electrode
#11110 : 11110
31 times per electrode
#11111 : 11111
32 times per electrode
End of enumeration elements list.
LPSCNITV : TSI Low Power Mode Scan Interval
bits : 24 - 27 (4 bit)
access : read-write
Enumeration:
#0000 : 0000
1 ms scan interval
#0001 : 0001
5 ms scan interval
#0010 : 0010
10 ms scan interval
#0011 : 0011
15 ms scan interval
#0100 : 0100
20 ms scan interval
#0101 : 0101
30 ms scan interval
#0110 : 0110
40 ms scan interval
#0111 : 0111
50 ms scan interval
#1000 : 1000
75 ms scan interval
#1001 : 1001
100 ms scan interval
#1010 : 1010
125 ms scan interval
#1011 : 1011
150 ms scan interval
#1100 : 1100
200 ms scan interval
#1101 : 1101
300 ms scan interval
#1110 : 1110
400 ms scan interval
#1111 : 1111
500 ms scan interval
End of enumeration elements list.
LPCLKS : Low Power Mode Clock Source Selection
bits : 28 - 28 (1 bit)
access : read-write
Enumeration:
#0 : 0
LPOCLK
#1 : 1
VLPOSCCLK
End of enumeration elements list.
Channel n threshold register
address_offset : 0x10F8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
HTHH : High threshold value
bits : 0 - 15 (16 bit)
access : read-write
LTHH : Low threshold value
bits : 16 - 31 (16 bit)
access : read-write
Channel n threshold register
address_offset : 0x124C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
HTHH : High threshold value
bits : 0 - 15 (16 bit)
access : read-write
LTHH : Low threshold value
bits : 16 - 31 (16 bit)
access : read-write
Channel n threshold register
address_offset : 0x13A4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
HTHH : High threshold value
bits : 0 - 15 (16 bit)
access : read-write
LTHH : Low threshold value
bits : 16 - 31 (16 bit)
access : read-write
Channel n threshold register
address_offset : 0x1500 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
HTHH : High threshold value
bits : 0 - 15 (16 bit)
access : read-write
LTHH : Low threshold value
bits : 16 - 31 (16 bit)
access : read-write
Counter Register
address_offset : 0x200 Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
CTN1 : Touch sensing channel n-1 counter value.
bits : 0 - 15 (16 bit)
access : read-only
CTN : Touch sensing channel n counter value.
bits : 16 - 31 (16 bit)
access : read-only
Channel n threshold register
address_offset : 0x240 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
HTHH : High threshold value
bits : 0 - 15 (16 bit)
access : read-write
LTHH : Low threshold value
bits : 16 - 31 (16 bit)
access : read-write
Counter Register
address_offset : 0x304 Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
CTN1 : Touch sensing channel n-1 counter value.
bits : 0 - 15 (16 bit)
access : read-only
CTN : Touch sensing channel n counter value.
bits : 16 - 31 (16 bit)
access : read-only
Channel n threshold register
address_offset : 0x364 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
HTHH : High threshold value
bits : 0 - 15 (16 bit)
access : read-write
LTHH : Low threshold value
bits : 16 - 31 (16 bit)
access : read-write
SCAN control register
address_offset : 0x4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
AMPSC : Active mode prescaler
bits : 0 - 2 (3 bit)
access : read-write
Enumeration:
#000 : 000
Input clock source divided by 1
#001 : 001
Input clock source divided by 2
#010 : 010
Input clock source divided by 4
#011 : 011
Input clock source divided by 8
#100 : 100
Input clock source divided by 16
#101 : 101
Input clock source divided by 32
#110 : 110
Input clock source divided by 64
#111 : 111
Input clock source divided by 128
End of enumeration elements list.
AMCLKS : Active mode clock source
bits : 3 - 4 (2 bit)
access : read-write
Enumeration:
#00 : 00
Bus Clock
#01 : 01
MCGIRCLK
#10 : 10
OSCERCLK
#11 : 11
Not valid
End of enumeration elements list.
AMCLKDIV : Active mode clock divider
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
Divider set to 1
#1 : 1
Divider set to 2048
End of enumeration elements list.
SMOD : Scan modulo
bits : 8 - 15 (8 bit)
access : read-write
Enumeration:
#00000000 : 00000000
Continuous scan
End of enumeration elements list.
DELVOL : Delta voltage select applied to analog oscillators
bits : 16 - 18 (3 bit)
access : read-write
Enumeration:
#000 : 000
100 mV delta voltage is applied
#001 : 001
150 mV delta voltage is applied
#010 : 010
200 mV delta voltage is applied
#011 : 011
250 mV delta voltage is applied
#100 : 100
300 mV delta voltage is applied
#101 : 101
400 mV delta voltage is applied
#110 : 110
500 mV delta voltage is applied
#111 : 111
600 mV delta voltage is applied
End of enumeration elements list.
EXTCHRG : External oscillator charge current select
bits : 19 - 23 (5 bit)
access : read-write
Enumeration:
#00000 : 00000
1 uA charge current
#00001 : 00001
2 uA charge current
#00010 : 00010
3 uA charge current
#00011 : 00011
4 uA charge current
#00100 : 00100
5 uA charge current
#00101 : 00101
6 uA charge current
#00110 : 00110
7 uA charge current
#00111 : 00111
8 uA charge current
#01000 : 01000
9 uA charge current
#01001 : 01001
10 uA charge current
#01010 : 01010
11 uA charge current
#01011 : 01011
12 uA charge current
#01100 : 01100
13 uA charge current
#01101 : 01101
14 uA charge current
#01110 : 01110
15 uA charge current
#01111 : 01111
16 uA charge current
#10000 : 10000
17 uA charge current
#10001 : 10001
18 uA charge current
#10010 : 10010
19 uA charge current
#10011 : 10011
20 uA charge current
#10100 : 10100
21 uA charge current
#10101 : 10101
22 uA charge current
#10110 : 10110
23 uA charge current
#10111 : 10111
24 uA charge current
#11000 : 11000
25 uA charge current
#11001 : 11001
26 uA charge current
#11010 : 11010
27 uA charge current
#11011 : 11011
28 uA charge current
#11100 : 11100
29 uA charge current
#11101 : 11101
30 uA charge current
#11110 : 11110
31 uA charge current
#11111 : 11111
32 uA charge current
End of enumeration elements list.
CAPTRM : Internal capacitance trim value
bits : 24 - 26 (3 bit)
access : read-write
Enumeration:
#000 : 000
0.5 pF internal reference capacitance
#001 : 001
0.6 pF internal reference capacitance
#010 : 010
0.7 pF internal reference capacitance
#011 : 011
0.8 pF internal reference capacitance
#100 : 100
0.9 pF internal reference capacitance
#101 : 101
1.0 pF internal reference capacitance
#110 : 110
1.1 pF internal reference capacitance
#111 : 111
1.2 pF internal reference capacitance
End of enumeration elements list.
REFCHRG : Reference oscillator charge current select
bits : 27 - 31 (5 bit)
access : read-write
Enumeration:
#00000 : 00000
1 uA charge current
#00001 : 00001
2 uA charge current
#00010 : 00010
3 uA charge current
#00011 : 00011
4 uA charge current
#00100 : 00100
5 uA charge current
#00101 : 00101
6 uA charge current
#00110 : 00110
7 uA charge current
#00111 : 00111
8 uA charge current
#01000 : 01000
9 uA charge current
#01001 : 01001
10 uA charge current
#01010 : 01010
11 uA charge current
#01011 : 01011
12 uA charge current
#01100 : 01100
13 uA charge current
#01101 : 01101
14 uA charge current
#01110 : 01110
15 uA charge current
#01111 : 01111
16 uA charge current
#10000 : 10000
17 uA charge current
#10001 : 10001
18 uA charge current
#10010 : 10010
19 uA charge current
#10011 : 10011
20 uA charge current
#10100 : 10100
21 uA charge current
#10101 : 10101
22 uA charge current
#10110 : 10110
23 uA charge current
#10111 : 10111
24 uA charge current
#11000 : 11000
25 uA charge current
#11001 : 11001
26 uA charge current
#11010 : 11010
27 uA charge current
#11011 : 11011
28 uA charge current
#11100 : 11100
29 uA charge current
#11101 : 11101
30 uA charge current
#11110 : 11110
31 uA charge current
#11111 : 11111
32 uA charge current
End of enumeration elements list.
Counter Register
address_offset : 0x40C Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
CTN1 : Touch sensing channel n-1 counter value.
bits : 0 - 15 (16 bit)
access : read-only
CTN : Touch sensing channel n counter value.
bits : 16 - 31 (16 bit)
access : read-only
Channel n threshold register
address_offset : 0x48C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
HTHH : High threshold value
bits : 0 - 15 (16 bit)
access : read-write
LTHH : Low threshold value
bits : 16 - 31 (16 bit)
access : read-write
Counter Register
address_offset : 0x518 Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
CTN1 : Touch sensing channel n-1 counter value.
bits : 0 - 15 (16 bit)
access : read-only
CTN : Touch sensing channel n counter value.
bits : 16 - 31 (16 bit)
access : read-only
Channel n threshold register
address_offset : 0x5B8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
HTHH : High threshold value
bits : 0 - 15 (16 bit)
access : read-write
LTHH : Low threshold value
bits : 16 - 31 (16 bit)
access : read-write
Counter Register
address_offset : 0x628 Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
CTN1 : Touch sensing channel n-1 counter value.
bits : 0 - 15 (16 bit)
access : read-only
CTN : Touch sensing channel n counter value.
bits : 16 - 31 (16 bit)
access : read-only
Channel n threshold register
address_offset : 0x6E8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
HTHH : High threshold value
bits : 0 - 15 (16 bit)
access : read-write
LTHH : Low threshold value
bits : 16 - 31 (16 bit)
access : read-write
Counter Register
address_offset : 0x73C Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
CTN1 : Touch sensing channel n-1 counter value.
bits : 0 - 15 (16 bit)
access : read-only
CTN : Touch sensing channel n counter value.
bits : 16 - 31 (16 bit)
access : read-only
Pin enable register
address_offset : 0x8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PEN0 : TSI pin 0 enable
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding pin is not used by TSI
#1 : 1
The corresponding pin is used by TSI
End of enumeration elements list.
PEN1 : TSI pin 1 enable
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding pin is not used by TSI
#1 : 1
The corresponding pin is used by TSI
End of enumeration elements list.
PEN2 : TSI pin 2 enable
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding pin is not used by TSI
#1 : 1
The corresponding pin is used by TSI
End of enumeration elements list.
PEN3 : TSI pin 3 enable
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding pin is not used by TSI
#1 : 1
The corresponding pin is used by TSI
End of enumeration elements list.
PEN4 : TSI pin 4 enable
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding pin is not used by TSI
#1 : 1
The corresponding pin is used by TSI
End of enumeration elements list.
PEN5 : TSI pin 5 enable
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding pin is not used by TSI
#1 : 1
The corresponding pin is used by TSI
End of enumeration elements list.
PEN6 : TSI pin 6 enable
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding pin is not used by TSI
#1 : 1
The corresponding pin is used by TSI
End of enumeration elements list.
PEN7 : TSI pin 7 enable
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding pin is not used by TSI
#1 : 1
The corresponding pin is used by TSI
End of enumeration elements list.
PEN8 : TSI pin 8 enable
bits : 8 - 8 (1 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding pin is not used by TSI
#1 : 1
The corresponding pin is used by TSI
End of enumeration elements list.
PEN9 : TSI pin 9 enable
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding pin is not used by TSI
#1 : 1
The corresponding pin is used by TSI
End of enumeration elements list.
PEN10 : TSI pin 10 enable
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding pin is not used by TSI
#1 : 1
The corresponding pin is used by TSI
End of enumeration elements list.
PEN11 : TSI pin 11 enable
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding pin is not used by TSI
#1 : 1
The corresponding pin is used by TSI
End of enumeration elements list.
PEN12 : TSI pin 12 enable
bits : 12 - 12 (1 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding pin is not used by TSI
#1 : 1
The corresponding pin is used by TSI
End of enumeration elements list.
PEN13 : TSI pin 13 enable
bits : 13 - 13 (1 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding pin is not used by TSI
#1 : 1
The corresponding pin is used by TSI
End of enumeration elements list.
PEN14 : TSI pin 14 enable
bits : 14 - 14 (1 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding pin is not used by TSI
#1 : 1
The corresponding pin is used by TSI
End of enumeration elements list.
PEN15 : TSI pin 15 enable
bits : 15 - 15 (1 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding pin is not used by TSI
#1 : 1
The corresponding pin is used by TSI
End of enumeration elements list.
LPSP : Low-power scan pin
bits : 16 - 19 (4 bit)
access : read-write
Enumeration:
#0000 : 0000
TSI_IN[0] is active in low power mode
#0001 : 0001
TSI_IN[1] is active in low power mode
#0010 : 0010
TSI_IN[2] is active in low power mode
#0011 : 0011
TSI_IN[3] is active in low power mode
#0100 : 0100
TSI_IN[4] is active in low power mode
#0101 : 0101
TSI_IN[5] is active in low power mode
#0110 : 0110
TSI_IN[6] is active in low power mode
#0111 : 0111
TSI_IN[7] is active in low power mode
#1000 : 1000
TSI_IN[8] is active in low power mode
#1001 : 1001
TSI_IN[9] is active in low power mode
#1010 : 1010
TSI_IN[10] is active in low power mode
#1011 : 1011
TSI_IN[11] is active in low power mode
#1100 : 1100
TSI_IN[12] is active in low power mode
#1101 : 1101
TSI_IN[13] is active in low power mode
#1110 : 1110
TSI_IN[14] is active in low power mode
#1111 : 1111
TSI_IN[15] is active in low power mode
End of enumeration elements list.
Channel n threshold register
address_offset : 0x81C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
HTHH : High threshold value
bits : 0 - 15 (16 bit)
access : read-write
LTHH : Low threshold value
bits : 16 - 31 (16 bit)
access : read-write
Counter Register
address_offset : 0x854 Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
CTN1 : Touch sensing channel n-1 counter value.
bits : 0 - 15 (16 bit)
access : read-only
CTN : Touch sensing channel n counter value.
bits : 16 - 31 (16 bit)
access : read-only
Channel n threshold register
address_offset : 0x954 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
HTHH : High threshold value
bits : 0 - 15 (16 bit)
access : read-write
LTHH : Low threshold value
bits : 16 - 31 (16 bit)
access : read-write
Counter Register
address_offset : 0x970 Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
CTN1 : Touch sensing channel n-1 counter value.
bits : 0 - 15 (16 bit)
access : read-only
CTN : Touch sensing channel n counter value.
bits : 16 - 31 (16 bit)
access : read-only
Channel n threshold register
address_offset : 0xA90 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
HTHH : High threshold value
bits : 0 - 15 (16 bit)
access : read-write
LTHH : Low threshold value
bits : 16 - 31 (16 bit)
access : read-write
Channel n threshold register
address_offset : 0xBD0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
HTHH : High threshold value
bits : 0 - 15 (16 bit)
access : read-write
LTHH : Low threshold value
bits : 16 - 31 (16 bit)
access : read-write
Status Register
address_offset : 0xC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
ORNGF0 : Touch Sensing Electrode Out-of-Range Flag 0
bits : 0 - 0 (1 bit)
access : read-write
ORNGF1 : Touch Sensing Electrode Out-of-Range Flag 1
bits : 1 - 1 (1 bit)
access : read-write
ORNGF2 : Touch Sensing Electrode Out-of-Range Flag 2
bits : 2 - 2 (1 bit)
access : read-write
ORNGF3 : Touch Sensing Electrode Out-of-Range Flag 3
bits : 3 - 3 (1 bit)
access : read-write
ORNGF4 : Touch Sensing Electrode Out-of-Range Flag 4
bits : 4 - 4 (1 bit)
access : read-write
ORNGF5 : Touch Sensing Electrode Out-of-Range Flag 5
bits : 5 - 5 (1 bit)
access : read-write
ORNGF6 : Touch Sensing Electrode Out-of-Range Flag 6
bits : 6 - 6 (1 bit)
access : read-write
ORNGF7 : Touch Sensing Electrode Out-of-Range Flag 7
bits : 7 - 7 (1 bit)
access : read-write
ORNGF8 : Touch Sensing Electrode Out-of-Range Flag 8
bits : 8 - 8 (1 bit)
access : read-write
ORNGF9 : Touch Sensing Electrode Out-of-Range Flag 9
bits : 9 - 9 (1 bit)
access : read-write
ORNGF10 : Touch Sensing Electrode Out-of-Range Flag 10
bits : 10 - 10 (1 bit)
access : read-write
ORNGF11 : Touch Sensing Electrode Out-of-Range Flag 11
bits : 11 - 11 (1 bit)
access : read-write
ORNGF12 : Touch Sensing Electrode Out-of-Range Flag 12
bits : 12 - 12 (1 bit)
access : read-write
ORNGF13 : Touch Sensing Electrode Out-of-Range Flag 13
bits : 13 - 13 (1 bit)
access : read-write
ORNGF14 : Touch Sensing Electrode Out-of-Range Flag 14
bits : 14 - 14 (1 bit)
access : read-write
ORNGF15 : Touch Sensing Electrode Out-of-Range Flag 15
bits : 15 - 15 (1 bit)
access : read-write
ERROF0 : TouchSensing Error Flag 0
bits : 16 - 16 (1 bit)
access : read-write
ERROF1 : TouchSensing Error Flag 1
bits : 17 - 17 (1 bit)
access : read-write
ERROF2 : TouchSensing Error Flag 2
bits : 18 - 18 (1 bit)
access : read-write
ERROF3 : TouchSensing Error Flag 3
bits : 19 - 19 (1 bit)
access : read-write
ERROF4 : TouchSensing Error Flag 4
bits : 20 - 20 (1 bit)
access : read-write
ERROF5 : TouchSensing Error Flag 5
bits : 21 - 21 (1 bit)
access : read-write
ERROF6 : TouchSensing Error Flag 6
bits : 22 - 22 (1 bit)
access : read-write
ERROF7 : TouchSensing Error Flag 7
bits : 23 - 23 (1 bit)
access : read-write
ERROF8 : TouchSensing Error Flag 8
bits : 24 - 24 (1 bit)
access : read-write
ERROF9 : TouchSensing Error Flag 9
bits : 25 - 25 (1 bit)
access : read-write
ERROF10 : TouchSensing Error Flag 10
bits : 26 - 26 (1 bit)
access : read-write
ERROF11 : TouchSensing Error Flag 11
bits : 27 - 27 (1 bit)
access : read-write
ERROF12 : TouchSensing Error Flag 12
bits : 28 - 28 (1 bit)
access : read-write
ERROF13 : TouchSensing Error Flag 13
bits : 29 - 29 (1 bit)
access : read-write
ERROF14 : TouchSensing Error Flag 14
bits : 30 - 30 (1 bit)
access : read-write
ERROF15 : TouchSensing Error Flag 15
bits : 31 - 31 (1 bit)
access : read-write
Channel n threshold register
address_offset : 0xD14 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
HTHH : High threshold value
bits : 0 - 15 (16 bit)
access : read-write
LTHH : Low threshold value
bits : 16 - 31 (16 bit)
access : read-write
Channel n threshold register
address_offset : 0xE5C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
HTHH : High threshold value
bits : 0 - 15 (16 bit)
access : read-write
LTHH : Low threshold value
bits : 16 - 31 (16 bit)
access : read-write
Channel n threshold register
address_offset : 0xFA8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
HTHH : High threshold value
bits : 0 - 15 (16 bit)
access : read-write
LTHH : Low threshold value
bits : 16 - 31 (16 bit)
access : read-write
Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !
This website is sponsored by Embeetle, an IDE designed from scratch for embedded software developers.