\n
address_offset : 0x0 Bytes (0x0)
size : 0x60 byte (0x0)
mem_usage : registers
protection : not protected
LCD General Control Register
address_offset : 0x0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DUTY : LCD duty select
bits : 0 - 2 (3 bit)
access : read-write
Enumeration:
#000 : 000
Use 1 BP (1/1 duty cycle).
#001 : 001
Use 2 BP (1/2 duty cycle).
#010 : 010
Use 3 BP (1/3 duty cycle).
#011 : 011
Use 4 BP (1/4 duty cycle). (Default)
#100 : 100
Use 5 BP (1/5 duty cycle).
#101 : 101
Use 6 BP (1/6 duty cycle).
#110 : 110
Use 7 BP (1/7 duty cycle).
#111 : 111
Use 8 BP (1/8 duty cycle).
End of enumeration elements list.
LCLK : LCD Clock Prescaler
bits : 3 - 5 (3 bit)
access : read-write
SOURCE : LCD Clock Source Select
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
Selects the default clock as the LCD clock source.
#1 : 1
Selects output of the alternate clock source selection (see ALTSOURCE) as the LCD clock source.
End of enumeration elements list.
LCDEN : LCD Driver Enable
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
All front plane and back plane pins are disabled. The LCD controller system is also disabled, and all LCD waveform generation clocks are stopped. V LL3 is connected to V DD internally.
#1 : 1
LCD controller driver system is enabled, and front plane and back plane waveforms are generated. All LCD pins, LCD_Pn, enabled if PAD_SAFE is clearusing the LCD Pin Enable register, output an LCD driver waveform. The back plane pins output an LCD driver back plane waveform based on the settings of DUTY[2:0]. Charge pump or resistor bias is enabled.
End of enumeration elements list.
LCDSTP : LCD Stop
bits : 8 - 8 (1 bit)
access : read-write
Enumeration:
#0 : 0
Allows the LCD driver, charge pump, resistor bias network, and voltage regulator to continue running during Stop mode.
#1 : 1
Disables the LCD driver, charge pump, resistor bias network, and voltage regulator when MCU enters Stop mode.
End of enumeration elements list.
LCDDOZE : LCD Doze enable
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
Allows the LCD driver, charge pump, resistor bias network, and voltage regulator to continue running during Doze mode.
#1 : 1
Disables the LCD driver, charge pump, resistor bias network, and voltage regulator when MCU enters Doze mode.
End of enumeration elements list.
FFR : Fast Frame Rate Select
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Standard Frame Rate LCD Frame Freq: 23.3 (min) 73.1 (max)
#1 : 1
Fast Frame Rate (Standard Frame Rate *2) LCD Frame Freq: 46.6 (min) 146.2 (max)
End of enumeration elements list.
ALTSOURCE : Selects the alternate clock source
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Select Alternate Clock Source 1 (default)
#1 : 1
Select Alternate Clock Source 2
End of enumeration elements list.
ALTDIV : LCD Alternate Clock Divider
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Divide factor = 1 (No divide)
#01 : 01
Divide factor = 64
#10 : 10
Divide factor = 256
#11 : 11
Divide factor = 512
End of enumeration elements list.
FDCIEN : LCD Fault Detection Complete Interrupt Enable
bits : 14 - 14 (1 bit)
access : read-write
Enumeration:
#0 : 0
No interrupt request is generated by this event.
#1 : 1
When a fault is detected and FDCF bit is set, this event causes an interrupt request.
End of enumeration elements list.
PADSAFE : Pad Safe State Enable
bits : 15 - 15 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD frontplane and backplane functions enabled according to other LCD control bits
#1 : 1
LCD frontplane and backplane functions disabled
End of enumeration elements list.
VSUPPLY : Voltage Supply Control
bits : 17 - 17 (1 bit)
access : read-write
Enumeration:
#0 : 0
Drive VLL3 internally from VDD
#1 : 1
Drive VLL3 externally from VDD or drive VLL1 internally from vIREG
End of enumeration elements list.
LADJ : Load Adjust
bits : 20 - 21 (2 bit)
access : read-write
CPSEL : Charge Pump or Resistor Bias Select
bits : 23 - 23 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD charge pump is disabled. Resistor network selected. (The internal 1/3-bias is forced.)
#1 : 1
LCD charge pump is selected. Resistor network disabled. (The internal 1/3-bias is forced.)
End of enumeration elements list.
RVTRIM : Regulated Voltage Trim
bits : 24 - 27 (4 bit)
access : read-write
RVEN : Regulated Voltage Enable
bits : 31 - 31 (1 bit)
access : read-write
Enumeration:
#0 : 0
Regulated voltage disabled.
#1 : 1
Regulated voltage enabled.
End of enumeration elements list.
LCD Pin Enable register
address_offset : 0x20 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PEN : LCD Pin Enable
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
LCD operation disabled on LCD_Pn.
#1 : 1
LCD operation enabled on LCD_Pn.
End of enumeration elements list.
LCD Waveform register
address_offset : 0x20 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : LCD
reset_Mask : 0x0
WF0 : Controls segments or phases connected to LCD_P0 as described above for WF3.
bits : 0 - 7 (8 bit)
access : read-write
WF1 : Controls segments or phases connected to LCD_P1 as described above for WF3.
bits : 8 - 15 (8 bit)
access : read-write
WF2 : Controls segments or phases connected to LCD_P2 as described above for WF3.
bits : 16 - 23 (8 bit)
access : read-write
WF3 : Segment-on front plane operation - Each bit turns on or off the segments associated with LCD_P3 in the following pattern: HGFEDCBA (most significant bit controls segment H and least significant bit controls segment A)
bits : 24 - 31 (8 bit)
access : read-write
LCD Waveform Register 0.
address_offset : 0x20 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
alternate_register : LCD
reset_Mask : 0x0
BPALCD0 : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase A
#1 : 1
LCD segment on or LCD backplane active for phase A
End of enumeration elements list.
BPBLCD0 : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase B
#1 : 1
LCD segment on or LCD backplane active for phase B
End of enumeration elements list.
BPCLCD0 : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase C
#1 : 1
LCD segment on or LCD backplane active for phase C
End of enumeration elements list.
BPDLCD0 : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase D
#1 : 1
LCD segment on or LCD backplane active for phase D
End of enumeration elements list.
BPELCD0 : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase E
#1 : 1
LCD segment on or LCD backplane active for phase E
End of enumeration elements list.
BPFLCD0 : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase F
#1 : 1
LCD segment on or LCD backplane active for phase F
End of enumeration elements list.
BPGLCD0 : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase G
#1 : 1
LCD segment on or LCD backplane active for phase G
End of enumeration elements list.
BPHLCD0 : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase H
#1 : 1
LCD segment on or LCD backplane active for phase H
End of enumeration elements list.
LCD Waveform Register 1.
address_offset : 0x21 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
BPALCD1 : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase A
#1 : 1
LCD segment on or LCD backplane active for phase A
End of enumeration elements list.
BPBLCD1 : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase B
#1 : 1
LCD segment on or LCD backplane active for phase B
End of enumeration elements list.
BPCLCD1 : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase C
#1 : 1
LCD segment on or LCD backplane active for phase C
End of enumeration elements list.
BPDLCD1 : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase D
#1 : 1
LCD segment on or LCD backplane active for phase D
End of enumeration elements list.
BPELCD1 : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase E
#1 : 1
LCD segment on or LCD backplane active for phase E
End of enumeration elements list.
BPFLCD1 : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase F
#1 : 1
LCD segment on or LCD backplane active for phase F
End of enumeration elements list.
BPGLCD1 : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase G
#1 : 1
LCD segment on or LCD backplane active for phase G
End of enumeration elements list.
BPHLCD1 : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase H
#1 : 1
LCD segment on or LCD backplane active for phase H
End of enumeration elements list.
LCD Waveform Register 2.
address_offset : 0x22 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
BPALCD2 : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase A
#1 : 1
LCD segment on or LCD backplane active for phase A
End of enumeration elements list.
BPBLCD2 : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase B
#1 : 1
LCD segment on or LCD backplane active for phase B
End of enumeration elements list.
BPCLCD2 : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase C
#1 : 1
LCD segment on or LCD backplane active for phase C
End of enumeration elements list.
BPDLCD2 : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase D
#1 : 1
LCD segment on or LCD backplane active for phase D
End of enumeration elements list.
BPELCD2 : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase E
#1 : 1
LCD segment on or LCD backplane active for phase E
End of enumeration elements list.
BPFLCD2 : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase F
#1 : 1
LCD segment on or LCD backplane active for phase F
End of enumeration elements list.
BPGLCD2 : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase G
#1 : 1
LCD segment on or LCD backplane active for phase G
End of enumeration elements list.
BPHLCD2 : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase H
#1 : 1
LCD segment on or LCD backplane active for phase H
End of enumeration elements list.
LCD Waveform Register 3.
address_offset : 0x23 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
BPALCD3 : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase A
#1 : 1
LCD segment on or LCD backplane active for phase A
End of enumeration elements list.
BPBLCD3 : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase B
#1 : 1
LCD segment on or LCD backplane active for phase B
End of enumeration elements list.
BPCLCD3 : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase C
#1 : 1
LCD segment on or LCD backplane active for phase C
End of enumeration elements list.
BPDLCD3 : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase D
#1 : 1
LCD segment on or LCD backplane active for phase D
End of enumeration elements list.
BPELCD3 : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase E
#1 : 1
LCD segment on or LCD backplane active for phase E
End of enumeration elements list.
BPFLCD3 : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase F
#1 : 1
LCD segment on or LCD backplane active for phase F
End of enumeration elements list.
BPGLCD3 : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase G
#1 : 1
LCD segment on or LCD backplane active for phase G
End of enumeration elements list.
BPHLCD3 : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase H
#1 : 1
LCD segment on or LCD backplane active for phase H
End of enumeration elements list.
LCD Waveform register
address_offset : 0x24 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : LCD
reset_Mask : 0x0
WF4 : Controls segments or phases connected to LCD_P4 as described above for WF3TO0[WF3].
bits : 0 - 7 (8 bit)
access : read-write
WF5 : Controls segments or phases connected to LCD_P5 as described above for WF3TO0[WF3].
bits : 8 - 15 (8 bit)
access : read-write
WF6 : Controls segments or phases connected to LCD_P6 as described above for WF3TO0[WF3].
bits : 16 - 23 (8 bit)
access : read-write
WF7 : Controls segments or phases connected to LCD_P7 as described above for WF3TO0[WF3].
bits : 24 - 31 (8 bit)
access : read-write
LCD Waveform Register 4.
address_offset : 0x24 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
alternate_register : LCD
reset_Mask : 0x0
BPALCD4 : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase A
#1 : 1
LCD segment on or LCD backplane active for phase A
End of enumeration elements list.
BPBLCD4 : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase B
#1 : 1
LCD segment on or LCD backplane active for phase B
End of enumeration elements list.
BPCLCD4 : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase C
#1 : 1
LCD segment on or LCD backplane active for phase C
End of enumeration elements list.
BPDLCD4 : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase D
#1 : 1
LCD segment on or LCD backplane active for phase D
End of enumeration elements list.
BPELCD4 : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase E
#1 : 1
LCD segment on or LCD backplane active for phase E
End of enumeration elements list.
BPFLCD4 : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase F
#1 : 1
LCD segment on or LCD backplane active for phase F
End of enumeration elements list.
BPGLCD4 : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase G
#1 : 1
LCD segment on or LCD backplane active for phase G
End of enumeration elements list.
BPHLCD4 : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase H
#1 : 1
LCD segment on or LCD backplane active for phase H
End of enumeration elements list.
LCD Waveform Register 5.
address_offset : 0x25 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
BPALCD5 : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase A
#1 : 1
LCD segment on or LCD backplane active for phase A
End of enumeration elements list.
BPBLCD5 : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase B
#1 : 1
LCD segment on or LCD backplane active for phase B
End of enumeration elements list.
BPCLCD5 : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase C
#1 : 1
LCD segment on or LCD backplane active for phase C
End of enumeration elements list.
BPDLCD5 : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase D
#1 : 1
LCD segment on or LCD backplane active for phase D
End of enumeration elements list.
BPELCD5 : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase E
#1 : 1
LCD segment on or LCD backplane active for phase E
End of enumeration elements list.
BPFLCD5 : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase F
#1 : 1
LCD segment on or LCD backplane active for phase F
End of enumeration elements list.
BPGLCD5 : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase G
#1 : 1
LCD segment on or LCD backplane active for phase G
End of enumeration elements list.
BPHLCD5 : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase H
#1 : 1
LCD segment on or LCD backplane active for phase H
End of enumeration elements list.
LCD Waveform Register 6.
address_offset : 0x26 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
BPALCD6 : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase A
#1 : 1
LCD segment on or LCD backplane active for phase A
End of enumeration elements list.
BPBLCD6 : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase B
#1 : 1
LCD segment on or LCD backplane active for phase B
End of enumeration elements list.
BPCLCD6 : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase C
#1 : 1
LCD segment on or LCD backplane active for phase C
End of enumeration elements list.
BPDLCD6 : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase D
#1 : 1
LCD segment on or LCD backplane active for phase D
End of enumeration elements list.
BPELCD6 : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase E
#1 : 1
LCD segment on or LCD backplane active for phase E
End of enumeration elements list.
BPFLCD6 : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase F
#1 : 1
LCD segment on or LCD backplane active for phase F
End of enumeration elements list.
BPGLCD6 : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase G
#1 : 1
LCD segment on or LCD backplane active for phase G
End of enumeration elements list.
BPHLCD6 : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase H
#1 : 1
LCD segment on or LCD backplane active for phase H
End of enumeration elements list.
LCD Waveform Register 7.
address_offset : 0x27 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
BPALCD7 : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase A
#1 : 1
LCD segment on or LCD backplane active for phase A
End of enumeration elements list.
BPBLCD7 : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase B
#1 : 1
LCD segment on or LCD backplane active for phase B
End of enumeration elements list.
BPCLCD7 : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase C
#1 : 1
LCD segment on or LCD backplane active for phase C
End of enumeration elements list.
BPDLCD7 : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase D
#1 : 1
LCD segment on or LCD backplane active for phase D
End of enumeration elements list.
BPELCD7 : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase E
#1 : 1
LCD segment on or LCD backplane active for phase E
End of enumeration elements list.
BPFLCD7 : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase F
#1 : 1
LCD segment on or LCD backplane active for phase F
End of enumeration elements list.
BPGLCD7 : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase G
#1 : 1
LCD segment on or LCD backplane active for phase G
End of enumeration elements list.
BPHLCD7 : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase H
#1 : 1
LCD segment on or LCD backplane active for phase H
End of enumeration elements list.
LCD Waveform register
address_offset : 0x28 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : LCD
reset_Mask : 0x0
WF8 : Controls segments or phases connected to LCD_P8 as described above for WF3TO0[WF3].
bits : 0 - 7 (8 bit)
access : read-write
WF9 : Controls segments or phases connected to LCD_P9 as described above for WF3TO0[WF3].
bits : 8 - 15 (8 bit)
access : read-write
WF10 : Controls segments or phases connected to LCD_P10 as described above for WF3TO0[WF3].
bits : 16 - 23 (8 bit)
access : read-write
WF11 : Controls segments or phases connected to LCD_P11 as described above for WF3TO0[WF3].
bits : 24 - 31 (8 bit)
access : read-write
LCD Waveform Register 8.
address_offset : 0x28 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
alternate_register : LCD
reset_Mask : 0x0
BPALCD8 : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase A
#1 : 1
LCD segment on or LCD backplane active for phase A
End of enumeration elements list.
BPBLCD8 : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase B
#1 : 1
LCD segment on or LCD backplane active for phase B
End of enumeration elements list.
BPCLCD8 : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase C
#1 : 1
LCD segment on or LCD backplane active for phase C
End of enumeration elements list.
BPDLCD8 : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase D
#1 : 1
LCD segment on or LCD backplane active for phase D
End of enumeration elements list.
BPELCD8 : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase E
#1 : 1
LCD segment on or LCD backplane active for phase E
End of enumeration elements list.
BPFLCD8 : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase F
#1 : 1
LCD segment on or LCD backplane active for phase F
End of enumeration elements list.
BPGLCD8 : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase G
#1 : 1
LCD segment on or LCD backplane active for phase G
End of enumeration elements list.
BPHLCD8 : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase H
#1 : 1
LCD segment on or LCD backplane active for phase H
End of enumeration elements list.
LCD Waveform Register 9.
address_offset : 0x29 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
BPALCD9 : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase A
#1 : 1
LCD segment on or LCD backplane active for phase A
End of enumeration elements list.
BPBLCD9 : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase B
#1 : 1
LCD segment on or LCD backplane active for phase B
End of enumeration elements list.
BPCLCD9 : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase C
#1 : 1
LCD segment on or LCD backplane active for phase C
End of enumeration elements list.
BPDLCD9 : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase D
#1 : 1
LCD segment on or LCD backplane active for phase D
End of enumeration elements list.
BPELCD9 : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase E
#1 : 1
LCD segment on or LCD backplane active for phase E
End of enumeration elements list.
BPFLCD9 : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase F
#1 : 1
LCD segment on or LCD backplane active for phase F
End of enumeration elements list.
BPGLCD9 : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase G
#1 : 1
LCD segment on or LCD backplane active for phase G
End of enumeration elements list.
BPHLCD9 : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase H
#1 : 1
LCD segment on or LCD backplane active for phase H
End of enumeration elements list.
LCD Waveform Register 10.
address_offset : 0x2A Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
BPALCD10 : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase A
#1 : 1
LCD segment on or LCD backplane active for phase A
End of enumeration elements list.
BPBLCD10 : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase B
#1 : 1
LCD segment on or LCD backplane active for phase B
End of enumeration elements list.
BPCLCD10 : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase C
#1 : 1
LCD segment on or LCD backplane active for phase C
End of enumeration elements list.
BPDLCD10 : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase D
#1 : 1
LCD segment on or LCD backplane active for phase D
End of enumeration elements list.
BPELCD10 : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase E
#1 : 1
LCD segment on or LCD backplane active for phase E
End of enumeration elements list.
BPFLCD10 : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase F
#1 : 1
LCD segment on or LCD backplane active for phase F
End of enumeration elements list.
BPGLCD10 : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase G
#1 : 1
LCD segment on or LCD backplane active for phase G
End of enumeration elements list.
BPHLCD10 : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase H
#1 : 1
LCD segment on or LCD backplane active for phase H
End of enumeration elements list.
LCD Waveform Register 11.
address_offset : 0x2B Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
BPALCD11 : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase A
#1 : 1
LCD segment on or LCD backplane active for phase A
End of enumeration elements list.
BPBLCD11 : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase B
#1 : 1
LCD segment on or LCD backplane active for phase B
End of enumeration elements list.
BPCLCD11 : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase C
#1 : 1
LCD segment on or LCD backplane active for phase C
End of enumeration elements list.
BPDLCD11 : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase D
#1 : 1
LCD segment on or LCD backplane active for phase D
End of enumeration elements list.
BPELCD11 : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase E
#1 : 1
LCD segment on or LCD backplane active for phase E
End of enumeration elements list.
BPFLCD11 : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase F
#1 : 1
LCD segment on or LCD backplane active for phase F
End of enumeration elements list.
BPGLCD11 : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase G
#1 : 1
LCD segment on or LCD backplane active for phase G
End of enumeration elements list.
BPHLCD11 : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase H
#1 : 1
LCD segment on or LCD backplane active for phase H
End of enumeration elements list.
LCD Waveform register
address_offset : 0x2C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : LCD
reset_Mask : 0x0
WF12 : Controls segments or phases connected to LCD_P12 as described above for WF3TO0[WF3].
bits : 0 - 7 (8 bit)
access : read-write
WF13 : Controls segments or phases connected to LCD_P13 as described above for WF3TO0[WF3].
bits : 8 - 15 (8 bit)
access : read-write
WF14 : Controls segments or phases connected to LCD_P14 as described above for WF3TO0[WF3].
bits : 16 - 23 (8 bit)
access : read-write
WF15 : Controls segments or phases connected to LCD_P15 as described above for WF3TO0[WF3].
bits : 24 - 31 (8 bit)
access : read-write
LCD Waveform Register 12.
address_offset : 0x2C Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
alternate_register : LCD
reset_Mask : 0x0
BPALCD12 : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase A
#1 : 1
LCD segment on or LCD backplane active for phase A
End of enumeration elements list.
BPBLCD12 : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase B
#1 : 1
LCD segment on or LCD backplane active for phase B
End of enumeration elements list.
BPCLCD12 : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase C
#1 : 1
LCD segment on or LCD backplane active for phase C
End of enumeration elements list.
BPDLCD12 : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase D
#1 : 1
LCD segment on or LCD backplane active for phase D
End of enumeration elements list.
BPELCD12 : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase E
#1 : 1
LCD segment on or LCD backplane active for phase E
End of enumeration elements list.
BPFLCD12 : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase F
#1 : 1
LCD segment on or LCD backplane active for phase F
End of enumeration elements list.
BPGLCD12 : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase G
#1 : 1
LCD segment on or LCD backplane active for phase G
End of enumeration elements list.
BPHLCD12 : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase H
#1 : 1
LCD segment on or LCD backplane active for phase H
End of enumeration elements list.
LCD Waveform Register 13.
address_offset : 0x2D Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
BPALCD13 : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase A
#1 : 1
LCD segment on or LCD backplane active for phase A
End of enumeration elements list.
BPBLCD13 : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase B
#1 : 1
LCD segment on or LCD backplane active for phase B
End of enumeration elements list.
BPCLCD13 : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase C
#1 : 1
LCD segment on or LCD backplane active for phase C
End of enumeration elements list.
BPDLCD13 : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase D
#1 : 1
LCD segment on or LCD backplane active for phase D
End of enumeration elements list.
BPELCD13 : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase E
#1 : 1
LCD segment on or LCD backplane active for phase E
End of enumeration elements list.
BPFLCD13 : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase F
#1 : 1
LCD segment on or LCD backplane active for phase F
End of enumeration elements list.
BPGLCD13 : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase G
#1 : 1
LCD segment on or LCD backplane active for phase G
End of enumeration elements list.
BPHLCD13 : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase H
#1 : 1
LCD segment on or LCD backplane active for phase H
End of enumeration elements list.
LCD Waveform Register 14.
address_offset : 0x2E Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
BPALCD14 : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase A
#1 : 1
LCD segment on or LCD backplane active for phase A
End of enumeration elements list.
BPBLCD14 : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase B
#1 : 1
LCD segment on or LCD backplane active for phase B
End of enumeration elements list.
BPCLCD14 : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase C
#1 : 1
LCD segment on or LCD backplane active for phase C
End of enumeration elements list.
BPDLCD14 : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase D
#1 : 1
LCD segment on or LCD backplane active for phase D
End of enumeration elements list.
BPELCD14 : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase E
#1 : 1
LCD segment on or LCD backplane active for phase E
End of enumeration elements list.
BPFLCD14 : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase F
#1 : 1
LCD segment on or LCD backplane active for phase F
End of enumeration elements list.
BPGLCD14 : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase G
#1 : 1
LCD segment on or LCD backplane active for phase G
End of enumeration elements list.
BPHLCD14 : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase H
#1 : 1
LCD segment on or LCD backplane active for phase H
End of enumeration elements list.
LCD Waveform Register 15.
address_offset : 0x2F Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
BPALCD15 : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase A
#1 : 1
LCD segment on or LCD backplane active for phase A
End of enumeration elements list.
BPBLCD15 : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase B
#1 : 1
LCD segment on or LCD backplane active for phase B
End of enumeration elements list.
BPCLCD15 : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase C
#1 : 1
LCD segment on or LCD backplane active for phase C
End of enumeration elements list.
BPDLCD15 : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase D
#1 : 1
LCD segment on or LCD backplane active for phase D
End of enumeration elements list.
BPELCD15 : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase E
#1 : 1
LCD segment on or LCD backplane active for phase E
End of enumeration elements list.
BPFLCD15 : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase F
#1 : 1
LCD segment on or LCD backplane active for phase F
End of enumeration elements list.
BPGLCD15 : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase G
#1 : 1
LCD segment on or LCD backplane active for phase G
End of enumeration elements list.
BPHLCD15 : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase H
#1 : 1
LCD segment on or LCD backplane active for phase H
End of enumeration elements list.
LCD Back Plane Enable register
address_offset : 0x30 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
BPEN : Back Plane Enable
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
Front plane operation enabled on LCD_Pn.
#1 : 1
Back plane operation enabled on LCD_Pn.
End of enumeration elements list.
LCD Waveform register
address_offset : 0x30 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : LCD
reset_Mask : 0x0
WF16 : Controls segments or phases connected to LCD_P16 as described above for WF3TO0[WF3].
bits : 0 - 7 (8 bit)
access : read-write
WF17 : Controls segments or phases connected to LCD_P17 as described above for WF3TO0[WF3].
bits : 8 - 15 (8 bit)
access : read-write
WF18 : Controls segments or phases connected to LCD_P18 as described above for WF3TO0[WF3].
bits : 16 - 23 (8 bit)
access : read-write
WF19 : Controls segments or phases connected to LCD_P19 as described above for WF3TO0[WF3].
bits : 24 - 31 (8 bit)
access : read-write
LCD Waveform Register 16.
address_offset : 0x30 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
alternate_register : LCD
reset_Mask : 0x0
BPALCD16 : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase A
#1 : 1
LCD segment on or LCD backplane active for phase A
End of enumeration elements list.
BPBLCD16 : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase B
#1 : 1
LCD segment on or LCD backplane active for phase B
End of enumeration elements list.
BPCLCD16 : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase C
#1 : 1
LCD segment on or LCD backplane active for phase C
End of enumeration elements list.
BPDLCD16 : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase D
#1 : 1
LCD segment on or LCD backplane active for phase D
End of enumeration elements list.
BPELCD16 : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase E
#1 : 1
LCD segment on or LCD backplane active for phase E
End of enumeration elements list.
BPFLCD16 : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase F
#1 : 1
LCD segment on or LCD backplane active for phase F
End of enumeration elements list.
BPGLCD16 : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase G
#1 : 1
LCD segment on or LCD backplane active for phase G
End of enumeration elements list.
BPHLCD16 : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase H
#1 : 1
LCD segment on or LCD backplane active for phase H
End of enumeration elements list.
LCD Waveform Register 17.
address_offset : 0x31 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
BPALCD17 : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase A
#1 : 1
LCD segment on or LCD backplane active for phase A
End of enumeration elements list.
BPBLCD17 : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase B
#1 : 1
LCD segment on or LCD backplane active for phase B
End of enumeration elements list.
BPCLCD17 : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase C
#1 : 1
LCD segment on or LCD backplane active for phase C
End of enumeration elements list.
BPDLCD17 : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase D
#1 : 1
LCD segment on or LCD backplane active for phase D
End of enumeration elements list.
BPELCD17 : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase E
#1 : 1
LCD segment on or LCD backplane active for phase E
End of enumeration elements list.
BPFLCD17 : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase F
#1 : 1
LCD segment on or LCD backplane active for phase F
End of enumeration elements list.
BPGLCD17 : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase G
#1 : 1
LCD segment on or LCD backplane active for phase G
End of enumeration elements list.
BPHLCD17 : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase H
#1 : 1
LCD segment on or LCD backplane active for phase H
End of enumeration elements list.
LCD Waveform Register 18.
address_offset : 0x32 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
BPALCD18 : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase A
#1 : 1
LCD segment on or LCD backplane active for phase A
End of enumeration elements list.
BPBLCD18 : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase B
#1 : 1
LCD segment on or LCD backplane active for phase B
End of enumeration elements list.
BPCLCD18 : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase C
#1 : 1
LCD segment on or LCD backplane active for phase C
End of enumeration elements list.
BPDLCD18 : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase D
#1 : 1
LCD segment on or LCD backplane active for phase D
End of enumeration elements list.
BPELCD18 : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase E
#1 : 1
LCD segment on or LCD backplane active for phase E
End of enumeration elements list.
BPFLCD18 : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase F
#1 : 1
LCD segment on or LCD backplane active for phase F
End of enumeration elements list.
BPGLCD18 : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase G
#1 : 1
LCD segment on or LCD backplane active for phase G
End of enumeration elements list.
BPHLCD18 : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase H
#1 : 1
LCD segment on or LCD backplane active for phase H
End of enumeration elements list.
LCD Waveform Register 19.
address_offset : 0x33 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
BPALCD19 : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase A
#1 : 1
LCD segment on or LCD backplane active for phase A
End of enumeration elements list.
BPBLCD19 : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase B
#1 : 1
LCD segment on or LCD backplane active for phase B
End of enumeration elements list.
BPCLCD19 : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase C
#1 : 1
LCD segment on or LCD backplane active for phase C
End of enumeration elements list.
BPDLCD19 : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase D
#1 : 1
LCD segment on or LCD backplane active for phase D
End of enumeration elements list.
BPELCD19 : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase E
#1 : 1
LCD segment on or LCD backplane active for phase E
End of enumeration elements list.
BPFLCD19 : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase F
#1 : 1
LCD segment on or LCD backplane active for phase F
End of enumeration elements list.
BPGLCD19 : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase G
#1 : 1
LCD segment on or LCD backplane active for phase G
End of enumeration elements list.
BPHLCD19 : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase H
#1 : 1
LCD segment on or LCD backplane active for phase H
End of enumeration elements list.
LCD Pin Enable register
address_offset : 0x34 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PEN : LCD Pin Enable
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
LCD operation disabled on LCD_Pn.
#1 : 1
LCD operation enabled on LCD_Pn.
End of enumeration elements list.
LCD Waveform register
address_offset : 0x34 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : LCD
reset_Mask : 0x0
WF20 : Controls segments or phases connected to LCD_P20 as described above for WF3TO0[WF3].
bits : 0 - 7 (8 bit)
access : read-write
WF21 : Controls segments or phases connected to LCD_P21 as described above for WF3TO0[WF3].
bits : 8 - 15 (8 bit)
access : read-write
WF22 : Controls segments or phases connected to LCD_P22 as described above for WF3TO0[WF3].
bits : 16 - 23 (8 bit)
access : read-write
WF23 : Controls segments or phases connected to LCD_P23 as described above for WF3TO0[WF3].
bits : 24 - 31 (8 bit)
access : read-write
LCD Waveform Register 20.
address_offset : 0x34 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
alternate_register : LCD
reset_Mask : 0x0
BPALCD20 : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase A
#1 : 1
LCD segment on or LCD backplane active for phase A
End of enumeration elements list.
BPBLCD20 : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase B
#1 : 1
LCD segment on or LCD backplane active for phase B
End of enumeration elements list.
BPCLCD20 : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase C
#1 : 1
LCD segment on or LCD backplane active for phase C
End of enumeration elements list.
BPDLCD20 : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase D
#1 : 1
LCD segment on or LCD backplane active for phase D
End of enumeration elements list.
BPELCD20 : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase E
#1 : 1
LCD segment on or LCD backplane active for phase E
End of enumeration elements list.
BPFLCD20 : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase F
#1 : 1
LCD segment on or LCD backplane active for phase F
End of enumeration elements list.
BPGLCD20 : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase G
#1 : 1
LCD segment on or LCD backplane active for phase G
End of enumeration elements list.
BPHLCD20 : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase H
#1 : 1
LCD segment on or LCD backplane active for phase H
End of enumeration elements list.
LCD Waveform Register 21.
address_offset : 0x35 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
BPALCD21 : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase A
#1 : 1
LCD segment on or LCD backplane active for phase A
End of enumeration elements list.
BPBLCD21 : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase B
#1 : 1
LCD segment on or LCD backplane active for phase B
End of enumeration elements list.
BPCLCD21 : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase C
#1 : 1
LCD segment on or LCD backplane active for phase C
End of enumeration elements list.
BPDLCD21 : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase D
#1 : 1
LCD segment on or LCD backplane active for phase D
End of enumeration elements list.
BPELCD21 : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase E
#1 : 1
LCD segment on or LCD backplane active for phase E
End of enumeration elements list.
BPFLCD21 : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase F
#1 : 1
LCD segment on or LCD backplane active for phase F
End of enumeration elements list.
BPGLCD21 : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase G
#1 : 1
LCD segment on or LCD backplane active for phase G
End of enumeration elements list.
BPHLCD21 : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase H
#1 : 1
LCD segment on or LCD backplane active for phase H
End of enumeration elements list.
LCD Waveform Register 22.
address_offset : 0x36 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
BPALCD22 : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase A
#1 : 1
LCD segment on or LCD backplane active for phase A
End of enumeration elements list.
BPBLCD22 : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase B
#1 : 1
LCD segment on or LCD backplane active for phase B
End of enumeration elements list.
BPCLCD22 : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase C
#1 : 1
LCD segment on or LCD backplane active for phase C
End of enumeration elements list.
BPDLCD22 : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase D
#1 : 1
LCD segment on or LCD backplane active for phase D
End of enumeration elements list.
BPELCD22 : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase E
#1 : 1
LCD segment on or LCD backplane active for phase E
End of enumeration elements list.
BPFLCD22 : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase F
#1 : 1
LCD segment on or LCD backplane active for phase F
End of enumeration elements list.
BPGLCD22 : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase G
#1 : 1
LCD segment on or LCD backplane active for phase G
End of enumeration elements list.
BPHLCD22 : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase H
#1 : 1
LCD segment on or LCD backplane active for phase H
End of enumeration elements list.
LCD Waveform Register 23.
address_offset : 0x37 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
BPALCD23 : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase A
#1 : 1
LCD segment on or LCD backplane active for phase A
End of enumeration elements list.
BPBLCD23 : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase B
#1 : 1
LCD segment on or LCD backplane active for phase B
End of enumeration elements list.
BPCLCD23 : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase C
#1 : 1
LCD segment on or LCD backplane active for phase C
End of enumeration elements list.
BPDLCD23 : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase D
#1 : 1
LCD segment on or LCD backplane active for phase D
End of enumeration elements list.
BPELCD23 : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase E
#1 : 1
LCD segment on or LCD backplane active for phase E
End of enumeration elements list.
BPFLCD23 : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase F
#1 : 1
LCD segment on or LCD backplane active for phase F
End of enumeration elements list.
BPGLCD23 : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase G
#1 : 1
LCD segment on or LCD backplane active for phase G
End of enumeration elements list.
BPHLCD23 : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase H
#1 : 1
LCD segment on or LCD backplane active for phase H
End of enumeration elements list.
LCD Waveform register
address_offset : 0x38 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : LCD
reset_Mask : 0x0
WF24 : Controls segments or phases connected to LCD_P24 as described above for WF3TO0[WF3].
bits : 0 - 7 (8 bit)
access : read-write
WF25 : Controls segments or phases connected to LCD_P25 as described above for WF3TO0[WF3].
bits : 8 - 15 (8 bit)
access : read-write
WF26 : Controls segments or phases connected to LCD_P26 as described above for WF3TO0[WF3].
bits : 16 - 23 (8 bit)
access : read-write
WF27 : Controls segments or phases connected to LCD_P27 as described above for WF3TO0[WF3].
bits : 24 - 31 (8 bit)
access : read-write
LCD Waveform Register 24.
address_offset : 0x38 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
alternate_register : LCD
reset_Mask : 0x0
BPALCD24 : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase A
#1 : 1
LCD segment on or LCD backplane active for phase A
End of enumeration elements list.
BPBLCD24 : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase B
#1 : 1
LCD segment on or LCD backplane active for phase B
End of enumeration elements list.
BPCLCD24 : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase C
#1 : 1
LCD segment on or LCD backplane active for phase C
End of enumeration elements list.
BPDLCD24 : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase D
#1 : 1
LCD segment on or LCD backplane active for phase D
End of enumeration elements list.
BPELCD24 : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase E
#1 : 1
LCD segment on or LCD backplane active for phase E
End of enumeration elements list.
BPFLCD24 : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase F
#1 : 1
LCD segment on or LCD backplane active for phase F
End of enumeration elements list.
BPGLCD24 : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase G
#1 : 1
LCD segment on or LCD backplane active for phase G
End of enumeration elements list.
BPHLCD24 : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase H
#1 : 1
LCD segment on or LCD backplane active for phase H
End of enumeration elements list.
LCD Waveform Register 25.
address_offset : 0x39 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
BPALCD25 : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase A
#1 : 1
LCD segment on or LCD backplane active for phase A
End of enumeration elements list.
BPBLCD25 : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase B
#1 : 1
LCD segment on or LCD backplane active for phase B
End of enumeration elements list.
BPCLCD25 : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase C
#1 : 1
LCD segment on or LCD backplane active for phase C
End of enumeration elements list.
BPDLCD25 : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase D
#1 : 1
LCD segment on or LCD backplane active for phase D
End of enumeration elements list.
BPELCD25 : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase E
#1 : 1
LCD segment on or LCD backplane active for phase E
End of enumeration elements list.
BPFLCD25 : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase F
#1 : 1
LCD segment on or LCD backplane active for phase F
End of enumeration elements list.
BPGLCD25 : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase G
#1 : 1
LCD segment on or LCD backplane active for phase G
End of enumeration elements list.
BPHLCD25 : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase H
#1 : 1
LCD segment on or LCD backplane active for phase H
End of enumeration elements list.
LCD Waveform Register 26.
address_offset : 0x3A Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
BPALCD26 : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase A
#1 : 1
LCD segment on or LCD backplane active for phase A
End of enumeration elements list.
BPBLCD26 : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase B
#1 : 1
LCD segment on or LCD backplane active for phase B
End of enumeration elements list.
BPCLCD26 : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase C
#1 : 1
LCD segment on or LCD backplane active for phase C
End of enumeration elements list.
BPDLCD26 : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase D
#1 : 1
LCD segment on or LCD backplane active for phase D
End of enumeration elements list.
BPELCD26 : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase E
#1 : 1
LCD segment on or LCD backplane active for phase E
End of enumeration elements list.
BPFLCD26 : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase F
#1 : 1
LCD segment on or LCD backplane active for phase F
End of enumeration elements list.
BPGLCD26 : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase G
#1 : 1
LCD segment on or LCD backplane active for phase G
End of enumeration elements list.
BPHLCD26 : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase H
#1 : 1
LCD segment on or LCD backplane active for phase H
End of enumeration elements list.
LCD Waveform Register 27.
address_offset : 0x3B Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
BPALCD27 : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase A
#1 : 1
LCD segment on or LCD backplane active for phase A
End of enumeration elements list.
BPBLCD27 : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase B
#1 : 1
LCD segment on or LCD backplane active for phase B
End of enumeration elements list.
BPCLCD27 : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase C
#1 : 1
LCD segment on or LCD backplane active for phase C
End of enumeration elements list.
BPDLCD27 : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase D
#1 : 1
LCD segment on or LCD backplane active for phase D
End of enumeration elements list.
BPELCD27 : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase E
#1 : 1
LCD segment on or LCD backplane active for phase E
End of enumeration elements list.
BPFLCD27 : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase F
#1 : 1
LCD segment on or LCD backplane active for phase F
End of enumeration elements list.
BPGLCD27 : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase G
#1 : 1
LCD segment on or LCD backplane active for phase G
End of enumeration elements list.
BPHLCD27 : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase H
#1 : 1
LCD segment on or LCD backplane active for phase H
End of enumeration elements list.
LCD Waveform register
address_offset : 0x3C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : LCD
reset_Mask : 0x0
WF28 : Controls segments or phases connected to LCD_P28 as described above for WF3TO0[WF3].
bits : 0 - 7 (8 bit)
access : read-write
WF29 : Controls segments or phases connected to LCD_P29 as described above for WF3TO0[WF3].
bits : 8 - 15 (8 bit)
access : read-write
WF30 : Controls segments or phases connected to LCD_P30 as described above for WF3TO0[WF3].
bits : 16 - 23 (8 bit)
access : read-write
WF31 : Controls segments or phases connected to LCD_P31 as described above for WF3TO0[WF3].
bits : 24 - 31 (8 bit)
access : read-write
LCD Waveform Register 28.
address_offset : 0x3C Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
alternate_register : LCD
reset_Mask : 0x0
BPALCD28 : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase A
#1 : 1
LCD segment on or LCD backplane active for phase A
End of enumeration elements list.
BPBLCD28 : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase B
#1 : 1
LCD segment on or LCD backplane active for phase B
End of enumeration elements list.
BPCLCD28 : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase C
#1 : 1
LCD segment on or LCD backplane active for phase C
End of enumeration elements list.
BPDLCD28 : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase D
#1 : 1
LCD segment on or LCD backplane active for phase D
End of enumeration elements list.
BPELCD28 : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase E
#1 : 1
LCD segment on or LCD backplane active for phase E
End of enumeration elements list.
BPFLCD28 : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase F
#1 : 1
LCD segment on or LCD backplane active for phase F
End of enumeration elements list.
BPGLCD28 : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase G
#1 : 1
LCD segment on or LCD backplane active for phase G
End of enumeration elements list.
BPHLCD28 : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase H
#1 : 1
LCD segment on or LCD backplane active for phase H
End of enumeration elements list.
LCD Waveform Register 29.
address_offset : 0x3D Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
BPALCD29 : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase A
#1 : 1
LCD segment on or LCD backplane active for phase A
End of enumeration elements list.
BPBLCD29 : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase B
#1 : 1
LCD segment on or LCD backplane active for phase B
End of enumeration elements list.
BPCLCD29 : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase C
#1 : 1
LCD segment on or LCD backplane active for phase C
End of enumeration elements list.
BPDLCD29 : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase D
#1 : 1
LCD segment on or LCD backplane active for phase D
End of enumeration elements list.
BPELCD29 : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase E
#1 : 1
LCD segment on or LCD backplane active for phase E
End of enumeration elements list.
BPFLCD29 : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase F
#1 : 1
LCD segment on or LCD backplane active for phase F
End of enumeration elements list.
BPGLCD29 : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase G
#1 : 1
LCD segment on or LCD backplane active for phase G
End of enumeration elements list.
BPHLCD29 : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase H
#1 : 1
LCD segment on or LCD backplane active for phase H
End of enumeration elements list.
LCD Waveform Register 30.
address_offset : 0x3E Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
BPALCD30 : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase A
#1 : 1
LCD segment on or LCD backplane active for phase A
End of enumeration elements list.
BPBLCD30 : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase B
#1 : 1
LCD segment on or LCD backplane active for phase B
End of enumeration elements list.
BPCLCD30 : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase C
#1 : 1
LCD segment on or LCD backplane active for phase C
End of enumeration elements list.
BPDLCD30 : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase D
#1 : 1
LCD segment on or LCD backplane active for phase D
End of enumeration elements list.
BPELCD30 : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase E
#1 : 1
LCD segment on or LCD backplane active for phase E
End of enumeration elements list.
BPFLCD30 : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase F
#1 : 1
LCD segment on or LCD backplane active for phase F
End of enumeration elements list.
BPGLCD30 : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase G
#1 : 1
LCD segment on or LCD backplane active for phase G
End of enumeration elements list.
BPHLCD30 : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase H
#1 : 1
LCD segment on or LCD backplane active for phase H
End of enumeration elements list.
LCD Waveform Register 31.
address_offset : 0x3F Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
BPALCD31 : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase A
#1 : 1
LCD segment on or LCD backplane active for phase A
End of enumeration elements list.
BPBLCD31 : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase B
#1 : 1
LCD segment on or LCD backplane active for phase B
End of enumeration elements list.
BPCLCD31 : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase C
#1 : 1
LCD segment on or LCD backplane active for phase C
End of enumeration elements list.
BPDLCD31 : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase D
#1 : 1
LCD segment on or LCD backplane active for phase D
End of enumeration elements list.
BPELCD31 : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase E
#1 : 1
LCD segment on or LCD backplane active for phase E
End of enumeration elements list.
BPFLCD31 : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase F
#1 : 1
LCD segment on or LCD backplane active for phase F
End of enumeration elements list.
BPGLCD31 : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase G
#1 : 1
LCD segment on or LCD backplane active for phase G
End of enumeration elements list.
BPHLCD31 : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase H
#1 : 1
LCD segment on or LCD backplane active for phase H
End of enumeration elements list.
LCD Auxiliary Register
address_offset : 0x4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
BRATE : Blink-rate configuration
bits : 0 - 2 (3 bit)
access : read-write
BMODE : Blink mode
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Display blank during the blink period.
#1 : 1
Display alternate display during blink period (Ignored if duty is 5 or greater).
End of enumeration elements list.
BLANK : Blank display mode
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
Normal or alternate display mode.
#1 : 1
Blank display mode.
End of enumeration elements list.
ALT : Alternate display mode
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
Normal display mode.
#1 : 1
Alternate display mode.
End of enumeration elements list.
BLINK : Blink command
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disables blinking.
#1 : 1
Starts blinking at blinking frequency specified by LCD blink rate calculation.
End of enumeration elements list.
LCD Waveform register
address_offset : 0x40 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : LCD
reset_Mask : 0x0
WF32 : Controls segments or phases connected to LCD_P32 as described above for WF3TO0[WF3].
bits : 0 - 7 (8 bit)
access : read-write
WF33 : Controls segments or phases connected to LCD_P33 as described above for WF3TO0[WF3].
bits : 8 - 15 (8 bit)
access : read-write
WF34 : Controls segments or phases connected to LCD_P34 as described above for WF3TO0[WF3].
bits : 16 - 23 (8 bit)
access : read-write
WF35 : Controls segments or phases connected to LCD_P35 as described above for WF3TO0[WF3].
bits : 24 - 31 (8 bit)
access : read-write
LCD Waveform Register 32.
address_offset : 0x40 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
alternate_register : LCD
reset_Mask : 0x0
BPALCD32 : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase A
#1 : 1
LCD segment on or LCD backplane active for phase A
End of enumeration elements list.
BPBLCD32 : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase B
#1 : 1
LCD segment on or LCD backplane active for phase B
End of enumeration elements list.
BPCLCD32 : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase C
#1 : 1
LCD segment on or LCD backplane active for phase C
End of enumeration elements list.
BPDLCD32 : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase D
#1 : 1
LCD segment on or LCD backplane active for phase D
End of enumeration elements list.
BPELCD32 : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase E
#1 : 1
LCD segment on or LCD backplane active for phase E
End of enumeration elements list.
BPFLCD32 : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase F
#1 : 1
LCD segment on or LCD backplane active for phase F
End of enumeration elements list.
BPGLCD32 : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase G
#1 : 1
LCD segment on or LCD backplane active for phase G
End of enumeration elements list.
BPHLCD32 : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase H
#1 : 1
LCD segment on or LCD backplane active for phase H
End of enumeration elements list.
LCD Waveform Register 33.
address_offset : 0x41 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
BPALCD33 : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase A
#1 : 1
LCD segment on or LCD backplane active for phase A
End of enumeration elements list.
BPBLCD33 : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase B
#1 : 1
LCD segment on or LCD backplane active for phase B
End of enumeration elements list.
BPCLCD33 : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase C
#1 : 1
LCD segment on or LCD backplane active for phase C
End of enumeration elements list.
BPDLCD33 : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase D
#1 : 1
LCD segment on or LCD backplane active for phase D
End of enumeration elements list.
BPELCD33 : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase E
#1 : 1
LCD segment on or LCD backplane active for phase E
End of enumeration elements list.
BPFLCD33 : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase F
#1 : 1
LCD segment on or LCD backplane active for phase F
End of enumeration elements list.
BPGLCD33 : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase G
#1 : 1
LCD segment on or LCD backplane active for phase G
End of enumeration elements list.
BPHLCD33 : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase H
#1 : 1
LCD segment on or LCD backplane active for phase H
End of enumeration elements list.
LCD Waveform Register 34.
address_offset : 0x42 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
BPALCD34 : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase A
#1 : 1
LCD segment on or LCD backplane active for phase A
End of enumeration elements list.
BPBLCD34 : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase B
#1 : 1
LCD segment on or LCD backplane active for phase B
End of enumeration elements list.
BPCLCD34 : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase C
#1 : 1
LCD segment on or LCD backplane active for phase C
End of enumeration elements list.
BPDLCD34 : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase D
#1 : 1
LCD segment on or LCD backplane active for phase D
End of enumeration elements list.
BPELCD34 : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase E
#1 : 1
LCD segment on or LCD backplane active for phase E
End of enumeration elements list.
BPFLCD34 : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase F
#1 : 1
LCD segment on or LCD backplane active for phase F
End of enumeration elements list.
BPGLCD34 : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase G
#1 : 1
LCD segment on or LCD backplane active for phase G
End of enumeration elements list.
BPHLCD34 : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase H
#1 : 1
LCD segment on or LCD backplane active for phase H
End of enumeration elements list.
LCD Waveform Register 35.
address_offset : 0x43 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
BPALCD35 : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase A
#1 : 1
LCD segment on or LCD backplane active for phase A
End of enumeration elements list.
BPBLCD35 : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase B
#1 : 1
LCD segment on or LCD backplane active for phase B
End of enumeration elements list.
BPCLCD35 : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase C
#1 : 1
LCD segment on or LCD backplane active for phase C
End of enumeration elements list.
BPDLCD35 : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase D
#1 : 1
LCD segment on or LCD backplane active for phase D
End of enumeration elements list.
BPELCD35 : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase E
#1 : 1
LCD segment on or LCD backplane active for phase E
End of enumeration elements list.
BPFLCD35 : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase F
#1 : 1
LCD segment on or LCD backplane active for phase F
End of enumeration elements list.
BPGLCD35 : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase G
#1 : 1
LCD segment on or LCD backplane active for phase G
End of enumeration elements list.
BPHLCD35 : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase H
#1 : 1
LCD segment on or LCD backplane active for phase H
End of enumeration elements list.
LCD Waveform register
address_offset : 0x44 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : LCD
reset_Mask : 0x0
WF36 : Controls segments or phases connected to LCD_P36 as described above for WF3TO0[WF3].
bits : 0 - 7 (8 bit)
access : read-write
WF37 : Controls segments or phases connected to LCD_P37 as described above for WF3TO0[WF3].
bits : 8 - 15 (8 bit)
access : read-write
WF38 : Controls segments or phases connected to LCD_P38 as described above for WF3TO0[WF3].
bits : 16 - 23 (8 bit)
access : read-write
WF39 : Controls segments or phases connected to LCD_P39 as described above for WF3TO0[WF3].
bits : 24 - 31 (8 bit)
access : read-write
LCD Waveform Register 36.
address_offset : 0x44 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
alternate_register : LCD
reset_Mask : 0x0
BPALCD36 : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase A
#1 : 1
LCD segment on or LCD backplane active for phase A
End of enumeration elements list.
BPBLCD36 : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase B
#1 : 1
LCD segment on or LCD backplane active for phase B
End of enumeration elements list.
BPCLCD36 : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase C
#1 : 1
LCD segment on or LCD backplane active for phase C
End of enumeration elements list.
BPDLCD36 : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase D
#1 : 1
LCD segment on or LCD backplane active for phase D
End of enumeration elements list.
BPELCD36 : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase E
#1 : 1
LCD segment on or LCD backplane active for phase E
End of enumeration elements list.
BPFLCD36 : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase F
#1 : 1
LCD segment on or LCD backplane active for phase F
End of enumeration elements list.
BPGLCD36 : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase G
#1 : 1
LCD segment on or LCD backplane active for phase G
End of enumeration elements list.
BPHLCD36 : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase H
#1 : 1
LCD segment on or LCD backplane active for phase H
End of enumeration elements list.
LCD Waveform Register 37.
address_offset : 0x45 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
BPALCD37 : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase A
#1 : 1
LCD segment on or LCD backplane active for phase A
End of enumeration elements list.
BPBLCD37 : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase B
#1 : 1
LCD segment on or LCD backplane active for phase B
End of enumeration elements list.
BPCLCD37 : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase C
#1 : 1
LCD segment on or LCD backplane active for phase C
End of enumeration elements list.
BPDLCD37 : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase D
#1 : 1
LCD segment on or LCD backplane active for phase D
End of enumeration elements list.
BPELCD37 : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase E
#1 : 1
LCD segment on or LCD backplane active for phase E
End of enumeration elements list.
BPFLCD37 : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase F
#1 : 1
LCD segment on or LCD backplane active for phase F
End of enumeration elements list.
BPGLCD37 : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase G
#1 : 1
LCD segment on or LCD backplane active for phase G
End of enumeration elements list.
BPHLCD37 : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase H
#1 : 1
LCD segment on or LCD backplane active for phase H
End of enumeration elements list.
LCD Waveform Register 38.
address_offset : 0x46 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
BPALCD38 : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase A
#1 : 1
LCD segment on or LCD backplane active for phase A
End of enumeration elements list.
BPBLCD38 : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase B
#1 : 1
LCD segment on or LCD backplane active for phase B
End of enumeration elements list.
BPCLCD38 : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase C
#1 : 1
LCD segment on or LCD backplane active for phase C
End of enumeration elements list.
BPDLCD38 : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase D
#1 : 1
LCD segment on or LCD backplane active for phase D
End of enumeration elements list.
BPELCD38 : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase E
#1 : 1
LCD segment on or LCD backplane active for phase E
End of enumeration elements list.
BPFLCD38 : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase F
#1 : 1
LCD segment on or LCD backplane active for phase F
End of enumeration elements list.
BPGLCD38 : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase G
#1 : 1
LCD segment on or LCD backplane active for phase G
End of enumeration elements list.
BPHLCD38 : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase H
#1 : 1
LCD segment on or LCD backplane active for phase H
End of enumeration elements list.
LCD Waveform Register 39.
address_offset : 0x47 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
BPALCD39 : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase A
#1 : 1
LCD segment on or LCD backplane active for phase A
End of enumeration elements list.
BPBLCD39 : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase B
#1 : 1
LCD segment on or LCD backplane active for phase B
End of enumeration elements list.
BPCLCD39 : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase C
#1 : 1
LCD segment on or LCD backplane active for phase C
End of enumeration elements list.
BPDLCD39 : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase D
#1 : 1
LCD segment on or LCD backplane active for phase D
End of enumeration elements list.
BPELCD39 : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase E
#1 : 1
LCD segment on or LCD backplane active for phase E
End of enumeration elements list.
BPFLCD39 : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase F
#1 : 1
LCD segment on or LCD backplane active for phase F
End of enumeration elements list.
BPGLCD39 : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase G
#1 : 1
LCD segment on or LCD backplane active for phase G
End of enumeration elements list.
BPHLCD39 : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase H
#1 : 1
LCD segment on or LCD backplane active for phase H
End of enumeration elements list.
LCD Waveform register
address_offset : 0x48 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : LCD
reset_Mask : 0x0
WF40 : Controls segments or phases connected to LCD_P40 as described above for WF3TO0[WF3].
bits : 0 - 7 (8 bit)
access : read-write
WF41 : Controls segments or phases connected to LCD_P41 as described above for WF3TO0[WF3].
bits : 8 - 15 (8 bit)
access : read-write
WF42 : Controls segments or phases connected to LCD_P42 as described above for WF3TO0[WF3].
bits : 16 - 23 (8 bit)
access : read-write
WF43 : Controls segments or phases connected to LCD_P43 as described above for WF3TO0[WF3].
bits : 24 - 31 (8 bit)
access : read-write
LCD Waveform Register 40.
address_offset : 0x48 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
alternate_register : LCD
reset_Mask : 0x0
BPALCD40 : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase A
#1 : 1
LCD segment on or LCD backplane active for phase A
End of enumeration elements list.
BPBLCD40 : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase B
#1 : 1
LCD segment on or LCD backplane active for phase B
End of enumeration elements list.
BPCLCD40 : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase C
#1 : 1
LCD segment on or LCD backplane active for phase C
End of enumeration elements list.
BPDLCD40 : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase D
#1 : 1
LCD segment on or LCD backplane active for phase D
End of enumeration elements list.
BPELCD40 : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase E
#1 : 1
LCD segment on or LCD backplane active for phase E
End of enumeration elements list.
BPFLCD40 : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase F
#1 : 1
LCD segment on or LCD backplane active for phase F
End of enumeration elements list.
BPGLCD40 : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase G
#1 : 1
LCD segment on or LCD backplane active for phase G
End of enumeration elements list.
BPHLCD40 : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase H
#1 : 1
LCD segment on or LCD backplane active for phase H
End of enumeration elements list.
LCD Waveform Register 41.
address_offset : 0x49 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
BPALCD41 : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase A
#1 : 1
LCD segment on or LCD backplane active for phase A
End of enumeration elements list.
BPBLCD41 : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase B
#1 : 1
LCD segment on or LCD backplane active for phase B
End of enumeration elements list.
BPCLCD41 : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase C
#1 : 1
LCD segment on or LCD backplane active for phase C
End of enumeration elements list.
BPDLCD41 : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase D
#1 : 1
LCD segment on or LCD backplane active for phase D
End of enumeration elements list.
BPELCD41 : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase E
#1 : 1
LCD segment on or LCD backplane active for phase E
End of enumeration elements list.
BPFLCD41 : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase F
#1 : 1
LCD segment on or LCD backplane active for phase F
End of enumeration elements list.
BPGLCD41 : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase G
#1 : 1
LCD segment on or LCD backplane active for phase G
End of enumeration elements list.
BPHLCD41 : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase H
#1 : 1
LCD segment on or LCD backplane active for phase H
End of enumeration elements list.
LCD Waveform Register 42.
address_offset : 0x4A Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
BPALCD42 : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase A
#1 : 1
LCD segment on or LCD backplane active for phase A
End of enumeration elements list.
BPBLCD42 : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase B
#1 : 1
LCD segment on or LCD backplane active for phase B
End of enumeration elements list.
BPCLCD42 : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase C
#1 : 1
LCD segment on or LCD backplane active for phase C
End of enumeration elements list.
BPDLCD42 : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase D
#1 : 1
LCD segment on or LCD backplane active for phase D
End of enumeration elements list.
BPELCD42 : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase E
#1 : 1
LCD segment on or LCD backplane active for phase E
End of enumeration elements list.
BPFLCD42 : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase F
#1 : 1
LCD segment on or LCD backplane active for phase F
End of enumeration elements list.
BPGLCD42 : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase G
#1 : 1
LCD segment on or LCD backplane active for phase G
End of enumeration elements list.
BPHLCD42 : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase H
#1 : 1
LCD segment on or LCD backplane active for phase H
End of enumeration elements list.
LCD Waveform Register 43.
address_offset : 0x4B Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
BPALCD43 : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase A
#1 : 1
LCD segment on or LCD backplane active for phase A
End of enumeration elements list.
BPBLCD43 : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase B
#1 : 1
LCD segment on or LCD backplane active for phase B
End of enumeration elements list.
BPCLCD43 : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase C
#1 : 1
LCD segment on or LCD backplane active for phase C
End of enumeration elements list.
BPDLCD43 : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase D
#1 : 1
LCD segment on or LCD backplane active for phase D
End of enumeration elements list.
BPELCD43 : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase E
#1 : 1
LCD segment on or LCD backplane active for phase E
End of enumeration elements list.
BPFLCD43 : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase F
#1 : 1
LCD segment on or LCD backplane active for phase F
End of enumeration elements list.
BPGLCD43 : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase G
#1 : 1
LCD segment on or LCD backplane active for phase G
End of enumeration elements list.
BPHLCD43 : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase H
#1 : 1
LCD segment on or LCD backplane active for phase H
End of enumeration elements list.
LCD Back Plane Enable register
address_offset : 0x4C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
BPEN : Back Plane Enable
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
Front plane operation enabled on LCD_Pn.
#1 : 1
Back plane operation enabled on LCD_Pn.
End of enumeration elements list.
LCD Waveform register
address_offset : 0x4C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : LCD
reset_Mask : 0x0
WF44 : Controls segments or phases connected to LCD_P44 as described above for WF3TO0[WF3].
bits : 0 - 7 (8 bit)
access : read-write
WF45 : Controls segments or phases connected to LCD_P45 as described above for WF3TO0[WF3].
bits : 8 - 15 (8 bit)
access : read-write
WF46 : Controls segments or phases connected to LCD_P46 as described above for WF3TO0[WF3].
bits : 16 - 23 (8 bit)
access : read-write
WF47 : Controls segments or phases connected to LCD_P47 as described above for WF3TO0[WF3].
bits : 24 - 31 (8 bit)
access : read-write
LCD Waveform Register 44.
address_offset : 0x4C Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
alternate_register : LCD
reset_Mask : 0x0
BPALCD44 : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase A
#1 : 1
LCD segment on or LCD backplane active for phase A
End of enumeration elements list.
BPBLCD44 : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase B
#1 : 1
LCD segment on or LCD backplane active for phase B
End of enumeration elements list.
BPCLCD44 : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase C
#1 : 1
LCD segment on or LCD backplane active for phase C
End of enumeration elements list.
BPDLCD44 : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase D
#1 : 1
LCD segment on or LCD backplane active for phase D
End of enumeration elements list.
BPELCD44 : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase E
#1 : 1
LCD segment on or LCD backplane active for phase E
End of enumeration elements list.
BPFLCD44 : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase F
#1 : 1
LCD segment on or LCD backplane active for phase F
End of enumeration elements list.
BPGLCD44 : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase G
#1 : 1
LCD segment on or LCD backplane active for phase G
End of enumeration elements list.
BPHLCD44 : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase H
#1 : 1
LCD segment on or LCD backplane active for phase H
End of enumeration elements list.
LCD Waveform Register 45.
address_offset : 0x4D Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
BPALCD45 : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase A
#1 : 1
LCD segment on or LCD backplane active for phase A
End of enumeration elements list.
BPBLCD45 : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase B
#1 : 1
LCD segment on or LCD backplane active for phase B
End of enumeration elements list.
BPCLCD45 : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase C
#1 : 1
LCD segment on or LCD backplane active for phase C
End of enumeration elements list.
BPDLCD45 : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase D
#1 : 1
LCD segment on or LCD backplane active for phase D
End of enumeration elements list.
BPELCD45 : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase E
#1 : 1
LCD segment on or LCD backplane active for phase E
End of enumeration elements list.
BPFLCD45 : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase F
#1 : 1
LCD segment on or LCD backplane active for phase F
End of enumeration elements list.
BPGLCD45 : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase G
#1 : 1
LCD segment on or LCD backplane active for phase G
End of enumeration elements list.
BPHLCD45 : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase H
#1 : 1
LCD segment on or LCD backplane active for phase H
End of enumeration elements list.
LCD Waveform Register 46.
address_offset : 0x4E Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
BPALCD46 : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase A
#1 : 1
LCD segment on or LCD backplane active for phase A
End of enumeration elements list.
BPBLCD46 : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase B
#1 : 1
LCD segment on or LCD backplane active for phase B
End of enumeration elements list.
BPCLCD46 : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase C
#1 : 1
LCD segment on or LCD backplane active for phase C
End of enumeration elements list.
BPDLCD46 : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase D
#1 : 1
LCD segment on or LCD backplane active for phase D
End of enumeration elements list.
BPELCD46 : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase E
#1 : 1
LCD segment on or LCD backplane active for phase E
End of enumeration elements list.
BPFLCD46 : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase F
#1 : 1
LCD segment on or LCD backplane active for phase F
End of enumeration elements list.
BPGLCD46 : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase G
#1 : 1
LCD segment on or LCD backplane active for phase G
End of enumeration elements list.
BPHLCD46 : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase H
#1 : 1
LCD segment on or LCD backplane active for phase H
End of enumeration elements list.
LCD Waveform Register 47.
address_offset : 0x4F Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
BPALCD47 : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase A
#1 : 1
LCD segment on or LCD backplane active for phase A
End of enumeration elements list.
BPBLCD47 : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase B
#1 : 1
LCD segment on or LCD backplane active for phase B
End of enumeration elements list.
BPCLCD47 : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase C
#1 : 1
LCD segment on or LCD backplane active for phase C
End of enumeration elements list.
BPDLCD47 : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase D
#1 : 1
LCD segment on or LCD backplane active for phase D
End of enumeration elements list.
BPELCD47 : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase E
#1 : 1
LCD segment on or LCD backplane active for phase E
End of enumeration elements list.
BPFLCD47 : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase F
#1 : 1
LCD segment on or LCD backplane active for phase F
End of enumeration elements list.
BPGLCD47 : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase G
#1 : 1
LCD segment on or LCD backplane active for phase G
End of enumeration elements list.
BPHLCD47 : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase H
#1 : 1
LCD segment on or LCD backplane active for phase H
End of enumeration elements list.
LCD Waveform register
address_offset : 0x50 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : LCD
reset_Mask : 0x0
WF48 : Controls segments or phases connected to LCD_P48 as described above for WF3TO0[WF3].
bits : 0 - 7 (8 bit)
access : read-write
WF49 : Controls segments or phases connected to LCD_P49 as described above for WF3TO0[WF3].
bits : 8 - 15 (8 bit)
access : read-write
WF50 : Controls segments or phases connected to LCD_P50 as described above for WF3TO0[WF3].
bits : 16 - 23 (8 bit)
access : read-write
WF51 : Controls segments or phases connected to LCD_P51 as described above for WF3TO0[WF3].
bits : 24 - 31 (8 bit)
access : read-write
LCD Waveform Register 48.
address_offset : 0x50 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
alternate_register : LCD
reset_Mask : 0x0
BPALCD48 : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase A
#1 : 1
LCD segment on or LCD backplane active for phase A
End of enumeration elements list.
BPBLCD48 : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase B
#1 : 1
LCD segment on or LCD backplane active for phase B
End of enumeration elements list.
BPCLCD48 : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase C
#1 : 1
LCD segment on or LCD backplane active for phase C
End of enumeration elements list.
BPDLCD48 : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase D
#1 : 1
LCD segment on or LCD backplane active for phase D
End of enumeration elements list.
BPELCD48 : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase E
#1 : 1
LCD segment on or LCD backplane active for phase E
End of enumeration elements list.
BPFLCD48 : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase F
#1 : 1
LCD segment on or LCD backplane active for phase F
End of enumeration elements list.
BPGLCD48 : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase G
#1 : 1
LCD segment on or LCD backplane active for phase G
End of enumeration elements list.
BPHLCD48 : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase H
#1 : 1
LCD segment on or LCD backplane active for phase H
End of enumeration elements list.
LCD Waveform Register 49.
address_offset : 0x51 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
BPALCD49 : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase A
#1 : 1
LCD segment on or LCD backplane active for phase A
End of enumeration elements list.
BPBLCD49 : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase B
#1 : 1
LCD segment on or LCD backplane active for phase B
End of enumeration elements list.
BPCLCD49 : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase C
#1 : 1
LCD segment on or LCD backplane active for phase C
End of enumeration elements list.
BPDLCD49 : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase D
#1 : 1
LCD segment on or LCD backplane active for phase D
End of enumeration elements list.
BPELCD49 : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase E
#1 : 1
LCD segment on or LCD backplane active for phase E
End of enumeration elements list.
BPFLCD49 : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase F
#1 : 1
LCD segment on or LCD backplane active for phase F
End of enumeration elements list.
BPGLCD49 : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase G
#1 : 1
LCD segment on or LCD backplane active for phase G
End of enumeration elements list.
BPHLCD49 : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase H
#1 : 1
LCD segment on or LCD backplane active for phase H
End of enumeration elements list.
LCD Waveform Register 50.
address_offset : 0x52 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
BPALCD50 : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase A
#1 : 1
LCD segment on or LCD backplane active for phase A
End of enumeration elements list.
BPBLCD50 : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase B
#1 : 1
LCD segment on or LCD backplane active for phase B
End of enumeration elements list.
BPCLCD50 : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase C
#1 : 1
LCD segment on or LCD backplane active for phase C
End of enumeration elements list.
BPDLCD50 : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase D
#1 : 1
LCD segment on or LCD backplane active for phase D
End of enumeration elements list.
BPELCD50 : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase E
#1 : 1
LCD segment on or LCD backplane active for phase E
End of enumeration elements list.
BPFLCD50 : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase F
#1 : 1
LCD segment on or LCD backplane active for phase F
End of enumeration elements list.
BPGLCD50 : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase G
#1 : 1
LCD segment on or LCD backplane active for phase G
End of enumeration elements list.
BPHLCD50 : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase H
#1 : 1
LCD segment on or LCD backplane active for phase H
End of enumeration elements list.
LCD Waveform Register 51.
address_offset : 0x53 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
BPALCD51 : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase A
#1 : 1
LCD segment on or LCD backplane active for phase A
End of enumeration elements list.
BPBLCD51 : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase B
#1 : 1
LCD segment on or LCD backplane active for phase B
End of enumeration elements list.
BPCLCD51 : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase C
#1 : 1
LCD segment on or LCD backplane active for phase C
End of enumeration elements list.
BPDLCD51 : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase D
#1 : 1
LCD segment on or LCD backplane active for phase D
End of enumeration elements list.
BPELCD51 : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase E
#1 : 1
LCD segment on or LCD backplane active for phase E
End of enumeration elements list.
BPFLCD51 : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase F
#1 : 1
LCD segment on or LCD backplane active for phase F
End of enumeration elements list.
BPGLCD51 : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase G
#1 : 1
LCD segment on or LCD backplane active for phase G
End of enumeration elements list.
BPHLCD51 : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase H
#1 : 1
LCD segment on or LCD backplane active for phase H
End of enumeration elements list.
LCD Waveform register
address_offset : 0x54 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : LCD
reset_Mask : 0x0
WF52 : Controls segments or phases connected to LCD_P52 as described above for WF3TO0[WF3].
bits : 0 - 7 (8 bit)
access : read-write
WF53 : Controls segments or phases connected to LCD_P53 as described above for WF3TO0[WF3].
bits : 8 - 15 (8 bit)
access : read-write
WF54 : Controls segments or phases connected to LCD_P54 as described above for WF3TO0[WF3].
bits : 16 - 23 (8 bit)
access : read-write
WF55 : Controls segments or phases connected to LCD_P55 as described above for WF3TO0[WF3].
bits : 24 - 31 (8 bit)
access : read-write
LCD Waveform Register 52.
address_offset : 0x54 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
alternate_register : LCD
reset_Mask : 0x0
BPALCD52 : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase A
#1 : 1
LCD segment on or LCD backplane active for phase A
End of enumeration elements list.
BPBLCD52 : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase B
#1 : 1
LCD segment on or LCD backplane active for phase B
End of enumeration elements list.
BPCLCD52 : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase C
#1 : 1
LCD segment on or LCD backplane active for phase C
End of enumeration elements list.
BPDLCD52 : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase D
#1 : 1
LCD segment on or LCD backplane active for phase D
End of enumeration elements list.
BPELCD52 : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase E
#1 : 1
LCD segment on or LCD backplane active for phase E
End of enumeration elements list.
BPFLCD52 : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase F
#1 : 1
LCD segment on or LCD backplane active for phase F
End of enumeration elements list.
BPGLCD52 : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase G
#1 : 1
LCD segment on or LCD backplane active for phase G
End of enumeration elements list.
BPHLCD52 : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase H
#1 : 1
LCD segment on or LCD backplane active for phase H
End of enumeration elements list.
LCD Waveform Register 53.
address_offset : 0x55 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
BPALCD53 : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase A
#1 : 1
LCD segment on or LCD backplane active for phase A
End of enumeration elements list.
BPBLCD53 : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase B
#1 : 1
LCD segment on or LCD backplane active for phase B
End of enumeration elements list.
BPCLCD53 : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase C
#1 : 1
LCD segment on or LCD backplane active for phase C
End of enumeration elements list.
BPDLCD53 : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase D
#1 : 1
LCD segment on or LCD backplane active for phase D
End of enumeration elements list.
BPELCD53 : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase E
#1 : 1
LCD segment on or LCD backplane active for phase E
End of enumeration elements list.
BPFLCD53 : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase F
#1 : 1
LCD segment on or LCD backplane active for phase F
End of enumeration elements list.
BPGLCD53 : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase G
#1 : 1
LCD segment on or LCD backplane active for phase G
End of enumeration elements list.
BPHLCD53 : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase H
#1 : 1
LCD segment on or LCD backplane active for phase H
End of enumeration elements list.
LCD Waveform Register 54.
address_offset : 0x56 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
BPALCD54 : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase A
#1 : 1
LCD segment on or LCD backplane active for phase A
End of enumeration elements list.
BPBLCD54 : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase B
#1 : 1
LCD segment on or LCD backplane active for phase B
End of enumeration elements list.
BPCLCD54 : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase C
#1 : 1
LCD segment on or LCD backplane active for phase C
End of enumeration elements list.
BPDLCD54 : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase D
#1 : 1
LCD segment on or LCD backplane active for phase D
End of enumeration elements list.
BPELCD54 : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase E
#1 : 1
LCD segment on or LCD backplane active for phase E
End of enumeration elements list.
BPFLCD54 : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase F
#1 : 1
LCD segment on or LCD backplane active for phase F
End of enumeration elements list.
BPGLCD54 : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase G
#1 : 1
LCD segment on or LCD backplane active for phase G
End of enumeration elements list.
BPHLCD54 : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase H
#1 : 1
LCD segment on or LCD backplane active for phase H
End of enumeration elements list.
LCD Waveform Register 55.
address_offset : 0x57 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
BPALCD55 : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase A
#1 : 1
LCD segment on or LCD backplane active for phase A
End of enumeration elements list.
BPBLCD55 : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase B
#1 : 1
LCD segment on or LCD backplane active for phase B
End of enumeration elements list.
BPCLCD55 : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase C
#1 : 1
LCD segment on or LCD backplane active for phase C
End of enumeration elements list.
BPDLCD55 : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase D
#1 : 1
LCD segment on or LCD backplane active for phase D
End of enumeration elements list.
BPELCD55 : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase E
#1 : 1
LCD segment on or LCD backplane active for phase E
End of enumeration elements list.
BPFLCD55 : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase F
#1 : 1
LCD segment on or LCD backplane active for phase F
End of enumeration elements list.
BPGLCD55 : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase G
#1 : 1
LCD segment on or LCD backplane active for phase G
End of enumeration elements list.
BPHLCD55 : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase H
#1 : 1
LCD segment on or LCD backplane active for phase H
End of enumeration elements list.
LCD Waveform register
address_offset : 0x58 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : LCD
reset_Mask : 0x0
WF56 : Controls segments or phases connected to LCD_P56 as described above for WF3TO0[WF3].
bits : 0 - 7 (8 bit)
access : read-write
WF57 : Controls segments or phases connected to LCD_P57 as described above for WF3TO0[WF3].
bits : 8 - 15 (8 bit)
access : read-write
WF58 : Controls segments or phases connected to LCD_P58 as described above for WF3TO0[WF3].
bits : 16 - 23 (8 bit)
access : read-write
WF59 : Controls segments or phases connected to LCD_P59 as described above for WF3TO0[WF3].
bits : 24 - 31 (8 bit)
access : read-write
LCD Waveform Register 56.
address_offset : 0x58 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
alternate_register : LCD
reset_Mask : 0x0
BPALCD56 : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase A
#1 : 1
LCD segment on or LCD backplane active for phase A
End of enumeration elements list.
BPBLCD56 : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase B
#1 : 1
LCD segment on or LCD backplane active for phase B
End of enumeration elements list.
BPCLCD56 : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase C
#1 : 1
LCD segment on or LCD backplane active for phase C
End of enumeration elements list.
BPDLCD56 : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase D
#1 : 1
LCD segment on or LCD backplane active for phase D
End of enumeration elements list.
BPELCD56 : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase E
#1 : 1
LCD segment on or LCD backplane active for phase E
End of enumeration elements list.
BPFLCD56 : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase F
#1 : 1
LCD segment on or LCD backplane active for phase F
End of enumeration elements list.
BPGLCD56 : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase G
#1 : 1
LCD segment on or LCD backplane active for phase G
End of enumeration elements list.
BPHLCD56 : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase H
#1 : 1
LCD segment on or LCD backplane active for phase H
End of enumeration elements list.
LCD Waveform Register 57.
address_offset : 0x59 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
BPALCD57 : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase A
#1 : 1
LCD segment on or LCD backplane active for phase A
End of enumeration elements list.
BPBLCD57 : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase B
#1 : 1
LCD segment on or LCD backplane active for phase B
End of enumeration elements list.
BPCLCD57 : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase C
#1 : 1
LCD segment on or LCD backplane active for phase C
End of enumeration elements list.
BPDLCD57 : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase D
#1 : 1
LCD segment on or LCD backplane active for phase D
End of enumeration elements list.
BPELCD57 : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase E
#1 : 1
LCD segment on or LCD backplane active for phase E
End of enumeration elements list.
BPFLCD57 : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase F
#1 : 1
LCD segment on or LCD backplane active for phase F
End of enumeration elements list.
BPGLCD57 : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase G
#1 : 1
LCD segment on or LCD backplane active for phase G
End of enumeration elements list.
BPHLCD57 : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase H
#1 : 1
LCD segment on or LCD backplane active for phase H
End of enumeration elements list.
LCD Waveform Register 58.
address_offset : 0x5A Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
BPALCD58 : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase A
#1 : 1
LCD segment on or LCD backplane active for phase A
End of enumeration elements list.
BPBLCD58 : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase B
#1 : 1
LCD segment on or LCD backplane active for phase B
End of enumeration elements list.
BPCLCD58 : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase C
#1 : 1
LCD segment on or LCD backplane active for phase C
End of enumeration elements list.
BPDLCD58 : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase D
#1 : 1
LCD segment on or LCD backplane active for phase D
End of enumeration elements list.
BPELCD58 : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase E
#1 : 1
LCD segment on or LCD backplane active for phase E
End of enumeration elements list.
BPFLCD58 : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase F
#1 : 1
LCD segment on or LCD backplane active for phase F
End of enumeration elements list.
BPGLCD58 : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase G
#1 : 1
LCD segment on or LCD backplane active for phase G
End of enumeration elements list.
BPHLCD58 : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase H
#1 : 1
LCD segment on or LCD backplane active for phase H
End of enumeration elements list.
LCD Waveform Register 59.
address_offset : 0x5B Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
BPALCD59 : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase A
#1 : 1
LCD segment on or LCD backplane active for phase A
End of enumeration elements list.
BPBLCD59 : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase B
#1 : 1
LCD segment on or LCD backplane active for phase B
End of enumeration elements list.
BPCLCD59 : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase C
#1 : 1
LCD segment on or LCD backplane active for phase C
End of enumeration elements list.
BPDLCD59 : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase D
#1 : 1
LCD segment on or LCD backplane active for phase D
End of enumeration elements list.
BPELCD59 : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase E
#1 : 1
LCD segment on or LCD backplane active for phase E
End of enumeration elements list.
BPFLCD59 : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase F
#1 : 1
LCD segment on or LCD backplane active for phase F
End of enumeration elements list.
BPGLCD59 : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase G
#1 : 1
LCD segment on or LCD backplane active for phase G
End of enumeration elements list.
BPHLCD59 : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase H
#1 : 1
LCD segment on or LCD backplane active for phase H
End of enumeration elements list.
LCD Waveform register
address_offset : 0x5C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : LCD
reset_Mask : 0x0
WF60 : Controls segments or phases connected to LCD_P60 as described above for WF3TO0[WF3].
bits : 0 - 7 (8 bit)
access : read-write
WF61 : Controls segments or phases connected to LCD_P61 as described above for WF3TO0[WF3].
bits : 8 - 15 (8 bit)
access : read-write
WF62 : Controls segments or phases connected to LCD_P62 as described above for WF3TO0[WF3].
bits : 16 - 23 (8 bit)
access : read-write
WF63 : Controls segments or phases connected to LCD_P63 as described above for WF3TO0[WF3].
bits : 24 - 31 (8 bit)
access : read-write
LCD Waveform Register 60.
address_offset : 0x5C Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
alternate_register : LCD
reset_Mask : 0x0
BPALCD60 : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase A
#1 : 1
LCD segment on or LCD backplane active for phase A
End of enumeration elements list.
BPBLCD60 : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase B
#1 : 1
LCD segment on or LCD backplane active for phase B
End of enumeration elements list.
BPCLCD60 : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase C
#1 : 1
LCD segment on or LCD backplane active for phase C
End of enumeration elements list.
BPDLCD60 : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase D
#1 : 1
LCD segment on or LCD backplane active for phase D
End of enumeration elements list.
BPELCD60 : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase E
#1 : 1
LCD segment on or LCD backplane active for phase E
End of enumeration elements list.
BPFLCD60 : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase F
#1 : 1
LCD segment on or LCD backplane active for phase F
End of enumeration elements list.
BPGLCD60 : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase G
#1 : 1
LCD segment on or LCD backplane active for phase G
End of enumeration elements list.
BPHLCD60 : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase H
#1 : 1
LCD segment on or LCD backplane active for phase H
End of enumeration elements list.
LCD Waveform Register 61.
address_offset : 0x5D Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
BPALCD61 : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase A
#1 : 1
LCD segment on or LCD backplane active for phase A
End of enumeration elements list.
BPBLCD61 : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase B
#1 : 1
LCD segment on or LCD backplane active for phase B
End of enumeration elements list.
BPCLCD61 : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase C
#1 : 1
LCD segment on or LCD backplane active for phase C
End of enumeration elements list.
BPDLCD61 : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase D
#1 : 1
LCD segment on or LCD backplane active for phase D
End of enumeration elements list.
BPELCD61 : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase E
#1 : 1
LCD segment on or LCD backplane active for phase E
End of enumeration elements list.
BPFLCD61 : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase F
#1 : 1
LCD segment on or LCD backplane active for phase F
End of enumeration elements list.
BPGLCD61 : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase G
#1 : 1
LCD segment on or LCD backplane active for phase G
End of enumeration elements list.
BPHLCD61 : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase H
#1 : 1
LCD segment on or LCD backplane active for phase H
End of enumeration elements list.
LCD Waveform Register 62.
address_offset : 0x5E Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
BPALCD62 : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase A
#1 : 1
LCD segment on or LCD backplane active for phase A
End of enumeration elements list.
BPBLCD62 : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase B
#1 : 1
LCD segment on or LCD backplane active for phase B
End of enumeration elements list.
BPCLCD62 : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase C
#1 : 1
LCD segment on or LCD backplane active for phase C
End of enumeration elements list.
BPDLCD62 : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase D
#1 : 1
LCD segment on or LCD backplane active for phase D
End of enumeration elements list.
BPELCD62 : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase E
#1 : 1
LCD segment on or LCD backplane active for phase E
End of enumeration elements list.
BPFLCD62 : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase F
#1 : 1
LCD segment on or LCD backplane active for phase F
End of enumeration elements list.
BPGLCD62 : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase G
#1 : 1
LCD segment on or LCD backplane active for phase G
End of enumeration elements list.
BPHLCD62 : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase H
#1 : 1
LCD segment on or LCD backplane active for phase H
End of enumeration elements list.
LCD Waveform Register 63.
address_offset : 0x5F Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
BPALCD63 : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase A
#1 : 1
LCD segment on or LCD backplane active for phase A
End of enumeration elements list.
BPBLCD63 : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase B
#1 : 1
LCD segment on or LCD backplane active for phase B
End of enumeration elements list.
BPCLCD63 : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase C
#1 : 1
LCD segment on or LCD backplane active for phase C
End of enumeration elements list.
BPDLCD63 : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase D
#1 : 1
LCD segment on or LCD backplane active for phase D
End of enumeration elements list.
BPELCD63 : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase E
#1 : 1
LCD segment on or LCD backplane active for phase E
End of enumeration elements list.
BPFLCD63 : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase F
#1 : 1
LCD segment on or LCD backplane active for phase F
End of enumeration elements list.
BPGLCD63 : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase G
#1 : 1
LCD segment on or LCD backplane active for phase G
End of enumeration elements list.
BPHLCD63 : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
LCD segment off or LCD backplane inactive for phase H
#1 : 1
LCD segment on or LCD backplane active for phase H
End of enumeration elements list.
LCD Fault Detect Control Register
address_offset : 0x8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FDPINID : Fault Detect Pin ID
bits : 0 - 5 (6 bit)
access : read-write
Enumeration:
#0 : 0
Fault detection for LCD_P0 pin.
#1 : 1
Fault detection for LCD_P1 pin.
#111111 : 111111
Fault detection for LCD_P63 pin.
End of enumeration elements list.
FDBPEN : Fault Detect Back Plane Enable
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
Type of the selected pin under fault detect test is front plane.
#1 : 1
Type of the selected pin under fault detect test is back plane.
End of enumeration elements list.
FDEN : Fault Detect Enable
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disable fault detection.
#1 : 1
Enable fault detection.
End of enumeration elements list.
FDSWW : Fault Detect Sample Window Width
bits : 9 - 11 (3 bit)
access : read-write
Enumeration:
#000 : 0
Sample window width is 4 sample clock cycles.
#001 : 1
Sample window width is 8 sample clock cycles.
#010 : 10
Sample window width is 16 sample clock cycles.
#011 : 11
Sample window width is 32 sample clock cycles.
#100 : 100
Sample window width is 64 sample clock cycles.
#101 : 101
Sample window width is 128 sample clock cycles.
#110 : 110
Sample window width is 256 sample clock cycles.
#111 : 111
Sample window width is 512 sample clock cycles.
End of enumeration elements list.
FDPRS : Fault Detect Clock Prescaler
bits : 12 - 14 (3 bit)
access : read-write
Enumeration:
#000 : 0
1/1 bus clock.
#001 : 1
1/2 bus clock.
#010 : 10
1/4 bus clock.
#011 : 11
1/8 bus clock.
#100 : 100
1/16 bus clock.
#101 : 101
1/32 bus clock.
#110 : 110
1/64 bus clock.
#111 : 111
1/128 bus clock.
End of enumeration elements list.
LCD Fault Detect Status Register
address_offset : 0xC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FDCNT : Fault Detect Counter
bits : 0 - 7 (8 bit)
access : read-only
Enumeration:
#0 : 0
No "one" samples.
#1 : 1
1 "one" samples.
#10 : 10
2 "one" samples.
#11111110 : 11111110
254 "one" samples.
#11111111 : 11111111
255 or more "one" samples. The FDCNT can overflow. Therefore, FDSWW and FDPRS must be reconfigured for proper sampling.
End of enumeration elements list.
FDCF : Fault Detection Complete Flag
bits : 15 - 15 (1 bit)
access : read-write
Enumeration:
#0 : 0
Fault detection is not completed.
#1 : 1
Fault detection is completed.
End of enumeration elements list.
Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !
This website is sponsored by Embeetle, an IDE designed from scratch for embedded software developers.