Embeetle, an IDE designed from scratch for embedded software developers.address_offset : 0x0 Bytes (0x0)
size : 0x88 byte (0x0)
mem_usage : registers
protection : not protected
Status and Control
address_offset : 0x0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PS : Prescale Factor Selection
bits : 0 - 2 (3 bit)
access : read-write
Enumeration:
#000 : 000
Divide by 1
#001 : 001
Divide by 2
#010 : 010
Divide by 4
#011 : 011
Divide by 8
#100 : 100
Divide by 16
#101 : 101
Divide by 32
#110 : 110
Divide by 64
#111 : 111
Divide by 128
End of enumeration elements list.
CMOD : Clock Mode Selection
bits : 3 - 4 (2 bit)
access : read-write
Enumeration:
#00 : 00
TPM counter is disabled
#01 : 01
TPM counter increments on every TPM counter clock
#10 : 10
TPM counter increments on rising edge of TPM_EXTCLK synchronized to the TPM counter clock
End of enumeration elements list.
CPWMS : Center-Aligned PWM Select
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
TPM counter operates in up counting mode.
#1 : 1
TPM counter operates in up-down counting mode.
End of enumeration elements list.
TOIE : Timer Overflow Interrupt Enable
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disable TOF interrupts. Use software polling or DMA request.
#1 : 1
Enable TOF interrupts. An interrupt is generated when TOF equals one.
End of enumeration elements list.
TOF : Timer Overflow Flag
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
TPM counter has not overflowed.
#1 : 1
TPM counter has overflowed.
End of enumeration elements list.
DMA : DMA Enable
bits : 8 - 8 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disables DMA transfers.
#1 : 1
Enables DMA transfers.
End of enumeration elements list.
Channel (n) Status and Control
address_offset : 0x18 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DMA : DMA Enable
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disable DMA transfers.
#1 : 1
Enable DMA transfers.
End of enumeration elements list.
ELSA : Edge or Level Select
bits : 2 - 2 (1 bit)
access : read-write
ELSB : Edge or Level Select
bits : 3 - 3 (1 bit)
access : read-write
MSA : Channel Mode Select
bits : 4 - 4 (1 bit)
access : read-write
MSB : Channel Mode Select
bits : 5 - 5 (1 bit)
access : read-write
CHIE : Channel Interrupt Enable
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disable channel interrupts.
#1 : 1
Enable channel interrupts.
End of enumeration elements list.
CHF : Channel Flag
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
No channel event has occurred.
#1 : 1
A channel event has occurred.
End of enumeration elements list.
Channel (n) Value
address_offset : 0x20 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
VAL : Channel Value
bits : 0 - 15 (16 bit)
access : read-write
Channel (n) Status and Control
address_offset : 0x2C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DMA : DMA Enable
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disable DMA transfers.
#1 : 1
Enable DMA transfers.
End of enumeration elements list.
ELSA : Edge or Level Select
bits : 2 - 2 (1 bit)
access : read-write
ELSB : Edge or Level Select
bits : 3 - 3 (1 bit)
access : read-write
MSA : Channel Mode Select
bits : 4 - 4 (1 bit)
access : read-write
MSB : Channel Mode Select
bits : 5 - 5 (1 bit)
access : read-write
CHIE : Channel Interrupt Enable
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disable channel interrupts.
#1 : 1
Enable channel interrupts.
End of enumeration elements list.
CHF : Channel Flag
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
No channel event has occurred.
#1 : 1
A channel event has occurred.
End of enumeration elements list.
Channel (n) Value
address_offset : 0x38 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
VAL : Channel Value
bits : 0 - 15 (16 bit)
access : read-write
Counter
address_offset : 0x4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COUNT : Counter value
bits : 0 - 15 (16 bit)
access : read-write
Capture and Compare Status
address_offset : 0x50 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
CH0F : Channel 0 Flag
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
No channel event has occurred.
#1 : 1
A channel event has occurred.
End of enumeration elements list.
CH1F : Channel 1 Flag
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
No channel event has occurred.
#1 : 1
A channel event has occurred.
End of enumeration elements list.
CH2F : Channel 2 Flag
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
No channel event has occurred.
#1 : 1
A channel event has occurred.
End of enumeration elements list.
CH3F : Channel 3 Flag
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
No channel event has occurred.
#1 : 1
A channel event has occurred.
End of enumeration elements list.
CH4F : Channel 4 Flag
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
No channel event has occurred.
#1 : 1
A channel event has occurred.
End of enumeration elements list.
CH5F : Channel 5 Flag
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
No channel event has occurred.
#1 : 1
A channel event has occurred.
End of enumeration elements list.
TOF : Timer Overflow Flag
bits : 8 - 8 (1 bit)
access : read-write
Enumeration:
#0 : 0
TPM counter has not overflowed.
#1 : 1
TPM counter has overflowed.
End of enumeration elements list.
Modulo
address_offset : 0x8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MOD : Modulo value
bits : 0 - 15 (16 bit)
access : read-write
Configuration
address_offset : 0x84 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DOZEEN : Doze Enable
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
Internal TPM counter continues in Doze mode.
#1 : 1
Internal TPM counter is paused and does not increment during Doze mode. Trigger inputs and input capture events are also ignored.
End of enumeration elements list.
DBGMODE : Debug Mode
bits : 6 - 7 (2 bit)
access : read-write
Enumeration:
#00 : 00
TPM counter is paused and does not increment during debug mode. Trigger inputs and input capture events are also ignored.
#11 : 11
TPM counter continues in debug mode.
End of enumeration elements list.
GTBEEN : Global time base enable
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
All channels use the internally generated TPM counter as their timebase
#1 : 1
All channels use an externally generated global timebase as their timebase
End of enumeration elements list.
CSOT : Counter Start on Trigger
bits : 16 - 16 (1 bit)
access : read-write
Enumeration:
#0 : 0
TPM counter starts to increment immediately, once it is enabled.
#1 : 1
TPM counter only starts to increment when it a rising edge on the selected input trigger is detected, after it has been enabled or after it has stopped due to overflow.
End of enumeration elements list.
CSOO : Counter Stop On Overflow
bits : 17 - 17 (1 bit)
access : read-write
Enumeration:
#0 : 0
TPM counter continues incrementing or decrementing after overflow
#1 : 1
TPM counter stops incrementing or decrementing after overflow.
End of enumeration elements list.
CROT : Counter Reload On Trigger
bits : 18 - 18 (1 bit)
access : read-write
Enumeration:
#0 : 0
Counter is not reloaded due to a rising edge on the selected input trigger
#1 : 1
Counter is reloaded when a rising edge is detected on the selected input trigger
End of enumeration elements list.
TRGSEL : Trigger Select
bits : 24 - 27 (4 bit)
access : read-write
Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !
This website is sponsored by Embeetle, an IDE designed from scratch for embedded software developers.