\n
address_offset : 0x0 Bytes (0x0)
size : 0x18 byte (0x0)
mem_usage : registers
protection : not protected
Watchdog Status and Control Register High
address_offset : 0x0 Bytes (0x0)
size : 16 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
WDOGEN : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
WDOG is disabled.
#1 : 1
WDOG is enabled.
End of enumeration elements list.
CLKSRC : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
WDOG clock sourced from LPO .
#1 : 1
WDOG clock sourced from alternate clock source.
End of enumeration elements list.
IRQRSTEN : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
WDOG time-out generates reset only.
#1 : 1
WDOG time-out initially generates an interrupt. After WCT, it generates a reset.
End of enumeration elements list.
WINEN : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Windowing mode is disabled.
#1 : 1
Windowing mode is enabled.
End of enumeration elements list.
ALLOWUPDATE : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
No further updates allowed to WDOG write-once registers.
#1 : 1
WDOG write-once registers can be unlocked for updating.
End of enumeration elements list.
DBGEN : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
WDOG is disabled in CPU Debug mode.
#1 : 1
WDOG is enabled in CPU Debug mode.
End of enumeration elements list.
STOPEN : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
WDOG is disabled in CPU Stop mode.
#1 : 1
WDOG is enabled in CPU Stop mode.
End of enumeration elements list.
WAITEN : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
WDOG is disabled in CPU Wait mode.
#1 : 1
WDOG is enabled in CPU Wait mode.
End of enumeration elements list.
RESERVED : no description available
bits : 8 - 8 (1 bit)
access : read-write
RESERVED : no description available
bits : 9 - 9 (1 bit)
access : read-only
TESTWDOG : no description available
bits : 10 - 10 (1 bit)
access : read-write
TESTSEL : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Quick test. The timer runs in normal operation. You can load a small time-out value to do a quick test.
#1 : 1
Byte test. Puts the timer in the byte test mode where individual bytes of the timer are enabled for operation and are compared for time-out against the corresponding byte of the programmed time-out value. Select the byte through BYTESEL[1:0] for testing.
End of enumeration elements list.
BYTESEL : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Byte 0 selected
#01 : 01
Byte 1 selected
#10 : 10
Byte 2 selected
#11 : 11
Byte 3 selected
End of enumeration elements list.
DISTESTWDOG : no description available
bits : 14 - 14 (1 bit)
access : read-write
Enumeration:
#0 : 0
WDOG functional test mode is not disabled.
#1 : 1
WDOG functional test mode is disabled permanently until reset.
End of enumeration elements list.
RESERVED : no description available
bits : 15 - 15 (1 bit)
access : read-only
Watchdog Timer Output Register High
address_offset : 0x10 Bytes (0x0)
size : 16 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TIMEROUTHIGH : no description available
bits : 0 - 15 (16 bit)
access : read-write
Watchdog Timer Output Register Low
address_offset : 0x12 Bytes (0x0)
size : 16 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TIMEROUTLOW : no description available
bits : 0 - 15 (16 bit)
access : read-write
Watchdog Reset Count register
address_offset : 0x14 Bytes (0x0)
size : 16 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RSTCNT : no description available
bits : 0 - 15 (16 bit)
access : read-write
Watchdog Prescaler register
address_offset : 0x16 Bytes (0x0)
size : 16 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RESERVED : no description available
bits : 0 - 7 (8 bit)
access : read-only
PRESCVAL : no description available
bits : 8 - 10 (3 bit)
access : read-write
RESERVED : no description available
bits : 11 - 15 (5 bit)
access : read-only
Watchdog Status and Control Register Low
address_offset : 0x2 Bytes (0x0)
size : 16 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RESERVED : no description available
bits : 0 - 14 (15 bit)
access : read-write
INTFLG : no description available
bits : 15 - 15 (1 bit)
access : read-write
Watchdog Time-out Value Register High
address_offset : 0x4 Bytes (0x0)
size : 16 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TOVALHIGH : no description available
bits : 0 - 15 (16 bit)
access : read-write
Watchdog Time-out Value Register Low
address_offset : 0x6 Bytes (0x0)
size : 16 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TOVALLOW : no description available
bits : 0 - 15 (16 bit)
access : read-write
Watchdog Window Register High
address_offset : 0x8 Bytes (0x0)
size : 16 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
WINHIGH : no description available
bits : 0 - 15 (16 bit)
access : read-write
Watchdog Window Register Low
address_offset : 0xA Bytes (0x0)
size : 16 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
WINLOW : no description available
bits : 0 - 15 (16 bit)
access : read-write
Watchdog Refresh register
address_offset : 0xC Bytes (0x0)
size : 16 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
WDOGREFRESH : no description available
bits : 0 - 15 (16 bit)
access : read-write
Watchdog Unlock register
address_offset : 0xE Bytes (0x0)
size : 16 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
WDOGUNLOCK : no description available
bits : 0 - 15 (16 bit)
access : read-write
Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !
This website is sponsored by Embeetle, an IDE designed from scratch for embedded software developers.