Embeetle, an IDE designed from scratch for embedded software developers.address_offset : 0x0 Bytes (0x0)
size : 0x4 byte (0x0)
mem_usage : registers
protection : not protected
ACMP Control and Status Register
address_offset : 0x0 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
ACMOD : ACMP MOD
bits : 0 - 1 (2 bit)
access : read-write
Enumeration:
#00 : 00
ACMP interrupt on output falling edge.
#01 : 01
ACMP interrupt on output rising edge.
#10 : 10
ACMP interrupt on output falling edge.
#11 : 11
ACMP interrupt on output falling or rising edge.
End of enumeration elements list.
ACOPE : ACMP Output Pin Enable
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
ACMP output cannot be placed onto external pin.
#1 : 1
ACMP output can be placed onto external pin.
End of enumeration elements list.
ACO : ACMP Output
bits : 3 - 3 (1 bit)
access : read-only
ACIE : ACMP Interrupt Enable
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disable the ACMP Interrupt.
#1 : 1
Enable the ACMP Interrupt.
End of enumeration elements list.
ACF : ACMP Interrupt Flag Bit
bits : 5 - 5 (1 bit)
access : read-write
HYST : Analog Comparator Hysterisis Selection
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
20 mV.
#1 : 1
30 mV.
End of enumeration elements list.
ACE : Analog Comparator Enable
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
The ACMP is disabled.
#1 : 1
The ACMP is enabled.
End of enumeration elements list.
ACMP Control Register 0
address_offset : 0x1 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
ACNSEL : ACMP Negative Input Select
bits : 0 - 1 (2 bit)
access : read-write
Enumeration:
#00 : 00
External reference 0
#01 : 01
External reference 1
#10 : 10
External reference 2
#11 : 11
DAC output
End of enumeration elements list.
RESERVED : no description available
bits : 2 - 3 (2 bit)
access : read-only
ACPSEL : ACMP Positive Input Select
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
External reference 0
#01 : 01
External reference 1
#10 : 10
External reference 2
#11 : 11
DAC output
End of enumeration elements list.
RESERVED : no description available
bits : 6 - 7 (2 bit)
access : read-only
ACMP Control Register 1
address_offset : 0x2 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DACVAL : DAC Output Level Selection
bits : 0 - 5 (6 bit)
access : read-write
DACREF : DAC Reference Select
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
The DAC selects Bandgap as the reference.
#1 : 1
The DAC selects VDDA as the reference.
End of enumeration elements list.
DACEN : DAC Enable
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
The DAC is disabled.
#1 : 1
The DAC is enabled.
End of enumeration elements list.
ACMP Control Register 2
address_offset : 0x3 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
ACIPE : ACMP Input Pin Enable
bits : 0 - 2 (3 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding external analog input is not allowed.
#1 : 1
The corresponding external analog input is allowed.
End of enumeration elements list.
RESERVED : no description available
bits : 3 - 7 (5 bit)
access : read-only
Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !
This website is sponsored by Embeetle, an IDE designed from scratch for embedded software developers.