\n

NVIC

Peripheral Memory Blocks

address_offset : 0x0 Bytes (0x0)
size : 0x320 byte (0x0)
mem_usage : registers
protection : not protected

Registers

ISER

ISPR

ICPR

IPR0

IPR1

IPR2

IPR3

IPR4

IPR5

IPR6

IPR7

ICER


ISER

Interrupt Set Enable Register
address_offset : 0x0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

ISER ISER read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SETENA0 SETENA1 SETENA2 SETENA3 SETENA4 SETENA5 SETENA6 SETENA7 SETENA8 SETENA9 SETENA10 SETENA11 SETENA12 SETENA13 SETENA14 SETENA15 SETENA16 SETENA17 SETENA18 SETENA19 SETENA20 SETENA21 SETENA22 SETENA23 SETENA24 SETENA25 SETENA26 SETENA27 SETENA28 SETENA29 SETENA30 SETENA31

SETENA0 : no description available
bits : 0 - 0 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Reserved iv 16 interrupt disabled

#1 : 1

write: enable Reserved iv 16 interrupt; read: Reserved iv 16 interrupt enabled

End of enumeration elements list.

SETENA1 : no description available
bits : 1 - 1 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Reserved iv 17 interrupt disabled

#1 : 1

write: enable Reserved iv 17 interrupt; read: Reserved iv 17 interrupt enabled

End of enumeration elements list.

SETENA2 : no description available
bits : 2 - 2 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Reserved iv 18 interrupt disabled

#1 : 1

write: enable Reserved iv 18 interrupt; read: Reserved iv 18 interrupt enabled

End of enumeration elements list.

SETENA3 : no description available
bits : 3 - 3 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Reserved iv 19 interrupt disabled

#1 : 1

write: enable Reserved iv 19 interrupt; read: Reserved iv 19 interrupt enabled

End of enumeration elements list.

SETENA4 : no description available
bits : 4 - 4 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Reserved iv 20 interrupt disabled

#1 : 1

write: enable Reserved iv 20 interrupt; read: Reserved iv 20 interrupt enabled

End of enumeration elements list.

SETENA5 : no description available
bits : 5 - 5 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Command complete and read collision interrupt disabled

#1 : 1

write: enable Command complete and read collision interrupt; read: Command complete and read collision interrupt enabled

End of enumeration elements list.

SETENA6 : no description available
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Low-voltage detect, low-voltage warning interrupt disabled

#1 : 1

write: enable Low-voltage detect, low-voltage warning interrupt; read: Low-voltage detect, low-voltage warning interrupt enabled

End of enumeration elements list.

SETENA7 : no description available
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: External Interrupt interrupt disabled

#1 : 1

write: enable External Interrupt interrupt; read: External Interrupt interrupt enabled

End of enumeration elements list.

SETENA8 : no description available
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Inter-Integrated Circuit 0 interrupt disabled

#1 : 1

write: enable Inter-Integrated Circuit 0 interrupt; read: Inter-Integrated Circuit 0 interrupt enabled

End of enumeration elements list.

SETENA9 : no description available
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Inter-Integrated Circuit 1 interrupt disabled

#1 : 1

write: enable Inter-Integrated Circuit 1 interrupt; read: Inter-Integrated Circuit 1 interrupt enabled

End of enumeration elements list.

SETENA10 : no description available
bits : 10 - 10 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Serial Peripheral Interface 0 interrupt disabled

#1 : 1

write: enable Serial Peripheral Interface 0 interrupt; read: Serial Peripheral Interface 0 interrupt enabled

End of enumeration elements list.

SETENA11 : no description available
bits : 11 - 11 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Serial Peripheral Interface 1 interrupt disabled

#1 : 1

write: enable Serial Peripheral Interface 1 interrupt; read: Serial Peripheral Interface 1 interrupt enabled

End of enumeration elements list.

SETENA12 : no description available
bits : 12 - 12 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: UART0 status and error interrupt disabled

#1 : 1

write: enable UART0 status and error interrupt; read: UART0 status and error interrupt enabled

End of enumeration elements list.

SETENA13 : no description available
bits : 13 - 13 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: UART1 status and error interrupt disabled

#1 : 1

write: enable UART1 status and error interrupt; read: UART1 status and error interrupt enabled

End of enumeration elements list.

SETENA14 : no description available
bits : 14 - 14 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: UART2 status and error interrupt disabled

#1 : 1

write: enable UART2 status and error interrupt; read: UART2 status and error interrupt enabled

End of enumeration elements list.

SETENA15 : no description available
bits : 15 - 15 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Analog-to-Digital Converter 0 interrupt disabled

#1 : 1

write: enable Analog-to-Digital Converter 0 interrupt; read: Analog-to-Digital Converter 0 interrupt enabled

End of enumeration elements list.

SETENA16 : no description available
bits : 16 - 16 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Analog comparator 0 interrupt interrupt disabled

#1 : 1

write: enable Analog comparator 0 interrupt interrupt; read: Analog comparator 0 interrupt interrupt enabled

End of enumeration elements list.

SETENA17 : no description available
bits : 17 - 17 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: FlexTimer Module 0 interrupt disabled

#1 : 1

write: enable FlexTimer Module 0 interrupt; read: FlexTimer Module 0 interrupt enabled

End of enumeration elements list.

SETENA18 : no description available
bits : 18 - 18 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: FlexTimer Module 1 interrupt disabled

#1 : 1

write: enable FlexTimer Module 1 interrupt; read: FlexTimer Module 1 interrupt enabled

End of enumeration elements list.

SETENA19 : no description available
bits : 19 - 19 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: FlexTimer Module 2 interrupt disabled

#1 : 1

write: enable FlexTimer Module 2 interrupt; read: FlexTimer Module 2 interrupt enabled

End of enumeration elements list.

SETENA20 : no description available
bits : 20 - 20 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Real-time counter interrupt disabled

#1 : 1

write: enable Real-time counter interrupt; read: Real-time counter interrupt enabled

End of enumeration elements list.

SETENA21 : no description available
bits : 21 - 21 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Analog comparator 1 interrupt interrupt disabled

#1 : 1

write: enable Analog comparator 1 interrupt interrupt; read: Analog comparator 1 interrupt interrupt enabled

End of enumeration elements list.

SETENA22 : no description available
bits : 22 - 22 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Periodic timer overflow channel 0 interrupt disabled

#1 : 1

write: enable Periodic timer overflow channel 0 interrupt; read: Periodic timer overflow channel 0 interrupt enabled

End of enumeration elements list.

SETENA23 : no description available
bits : 23 - 23 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Periodic timer overflow channel 1 interrupt disabled

#1 : 1

write: enable Periodic timer overflow channel 1 interrupt; read: Periodic timer overflow channel 1 interrupt enabled

End of enumeration elements list.

SETENA24 : no description available
bits : 24 - 24 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Keyboard interrupt interrupt disabled

#1 : 1

write: enable Keyboard interrupt interrupt; read: Keyboard interrupt interrupt enabled

End of enumeration elements list.

SETENA25 : no description available
bits : 25 - 25 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Keyboard interrupt interrupt disabled

#1 : 1

write: enable Keyboard interrupt interrupt; read: Keyboard interrupt interrupt enabled

End of enumeration elements list.

SETENA26 : no description available
bits : 26 - 26 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Reserved iv 42 interrupt disabled

#1 : 1

write: enable Reserved iv 42 interrupt; read: Reserved iv 42 interrupt enabled

End of enumeration elements list.

SETENA27 : no description available
bits : 27 - 27 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Clock loss of lock interrupt disabled

#1 : 1

write: enable Clock loss of lock interrupt; read: Clock loss of lock interrupt enabled

End of enumeration elements list.

SETENA28 : no description available
bits : 28 - 28 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: WDOG interrupt disabled

#1 : 1

write: enable WDOG interrupt; read: WDOG interrupt enabled

End of enumeration elements list.

SETENA29 : no description available
bits : 29 - 29 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Pulse width timer interrupt disabled

#1 : 1

write: enable Pulse width timer interrupt; read: Pulse width timer interrupt enabled

End of enumeration elements list.

SETENA30 : no description available
bits : 30 - 30 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Freescale's Scalable Controller Area Network Rx interrupt disabled

#1 : 1

write: enable Freescale's Scalable Controller Area Network Rx interrupt; read: Freescale's Scalable Controller Area Network Rx interrupt enabled

End of enumeration elements list.

SETENA31 : no description available
bits : 31 - 31 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Freescale's Scalable Controller Area Network Tx and error interrupt disabled

#1 : 1

write: enable Freescale's Scalable Controller Area Network Tx and error interrupt; read: Freescale's Scalable Controller Area Network Tx and error interrupt enabled

End of enumeration elements list.


ISPR

Interrupt Set Pending Register
address_offset : 0x100 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

ISPR ISPR read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SETPEND0 SETPEND1 SETPEND2 SETPEND3 SETPEND4 SETPEND5 SETPEND6 SETPEND7 SETPEND8 SETPEND9 SETPEND10 SETPEND11 SETPEND12 SETPEND13 SETPEND14 SETPEND15 SETPEND16 SETPEND17 SETPEND18 SETPEND19 SETPEND20 SETPEND21 SETPEND22 SETPEND23 SETPEND24 SETPEND25 SETPEND26 SETPEND27 SETPEND28 SETPEND29 SETPEND30 SETPEND31

SETPEND0 : no description available
bits : 0 - 0 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Reserved iv 16 interrupt is not pending

#1 : 1

write: changes the Reserved iv 16 interrupt state to pending; read: Reserved iv 16 interrupt is pending

End of enumeration elements list.

SETPEND1 : no description available
bits : 1 - 1 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Reserved iv 17 interrupt is not pending

#1 : 1

write: changes the Reserved iv 17 interrupt state to pending; read: Reserved iv 17 interrupt is pending

End of enumeration elements list.

SETPEND2 : no description available
bits : 2 - 2 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Reserved iv 18 interrupt is not pending

#1 : 1

write: changes the Reserved iv 18 interrupt state to pending; read: Reserved iv 18 interrupt is pending

End of enumeration elements list.

SETPEND3 : no description available
bits : 3 - 3 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Reserved iv 19 interrupt is not pending

#1 : 1

write: changes the Reserved iv 19 interrupt state to pending; read: Reserved iv 19 interrupt is pending

End of enumeration elements list.

SETPEND4 : no description available
bits : 4 - 4 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Reserved iv 20 interrupt is not pending

#1 : 1

write: changes the Reserved iv 20 interrupt state to pending; read: Reserved iv 20 interrupt is pending

End of enumeration elements list.

SETPEND5 : no description available
bits : 5 - 5 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Command complete and read collision interrupt is not pending

#1 : 1

write: changes the Command complete and read collision interrupt state to pending; read: Command complete and read collision interrupt is pending

End of enumeration elements list.

SETPEND6 : no description available
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Low-voltage detect, low-voltage warning interrupt is not pending

#1 : 1

write: changes the Low-voltage detect, low-voltage warning interrupt state to pending; read: Low-voltage detect, low-voltage warning interrupt is pending

End of enumeration elements list.

SETPEND7 : no description available
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: External Interrupt interrupt is not pending

#1 : 1

write: changes the External Interrupt interrupt state to pending; read: External Interrupt interrupt is pending

End of enumeration elements list.

SETPEND8 : no description available
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Inter-Integrated Circuit 0 interrupt is not pending

#1 : 1

write: changes the Inter-Integrated Circuit 0 interrupt state to pending; read: Inter-Integrated Circuit 0 interrupt is pending

End of enumeration elements list.

SETPEND9 : no description available
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Inter-Integrated Circuit 1 interrupt is not pending

#1 : 1

write: changes the Inter-Integrated Circuit 1 interrupt state to pending; read: Inter-Integrated Circuit 1 interrupt is pending

End of enumeration elements list.

SETPEND10 : no description available
bits : 10 - 10 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Serial Peripheral Interface 0 interrupt is not pending

#1 : 1

write: changes the Serial Peripheral Interface 0 interrupt state to pending; read: Serial Peripheral Interface 0 interrupt is pending

End of enumeration elements list.

SETPEND11 : no description available
bits : 11 - 11 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Serial Peripheral Interface 1 interrupt is not pending

#1 : 1

write: changes the Serial Peripheral Interface 1 interrupt state to pending; read: Serial Peripheral Interface 1 interrupt is pending

End of enumeration elements list.

SETPEND12 : no description available
bits : 12 - 12 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: UART0 status and error interrupt is not pending

#1 : 1

write: changes the UART0 status and error interrupt state to pending; read: UART0 status and error interrupt is pending

End of enumeration elements list.

SETPEND13 : no description available
bits : 13 - 13 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: UART1 status and error interrupt is not pending

#1 : 1

write: changes the UART1 status and error interrupt state to pending; read: UART1 status and error interrupt is pending

End of enumeration elements list.

SETPEND14 : no description available
bits : 14 - 14 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: UART2 status and error interrupt is not pending

#1 : 1

write: changes the UART2 status and error interrupt state to pending; read: UART2 status and error interrupt is pending

End of enumeration elements list.

SETPEND15 : no description available
bits : 15 - 15 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Analog-to-Digital Converter 0 interrupt is not pending

#1 : 1

write: changes the Analog-to-Digital Converter 0 interrupt state to pending; read: Analog-to-Digital Converter 0 interrupt is pending

End of enumeration elements list.

SETPEND16 : no description available
bits : 16 - 16 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Analog comparator 0 interrupt interrupt is not pending

#1 : 1

write: changes the Analog comparator 0 interrupt interrupt state to pending; read: Analog comparator 0 interrupt interrupt is pending

End of enumeration elements list.

SETPEND17 : no description available
bits : 17 - 17 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: FlexTimer Module 0 interrupt is not pending

#1 : 1

write: changes the FlexTimer Module 0 interrupt state to pending; read: FlexTimer Module 0 interrupt is pending

End of enumeration elements list.

SETPEND18 : no description available
bits : 18 - 18 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: FlexTimer Module 1 interrupt is not pending

#1 : 1

write: changes the FlexTimer Module 1 interrupt state to pending; read: FlexTimer Module 1 interrupt is pending

End of enumeration elements list.

SETPEND19 : no description available
bits : 19 - 19 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: FlexTimer Module 2 interrupt is not pending

#1 : 1

write: changes the FlexTimer Module 2 interrupt state to pending; read: FlexTimer Module 2 interrupt is pending

End of enumeration elements list.

SETPEND20 : no description available
bits : 20 - 20 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Real-time counter interrupt is not pending

#1 : 1

write: changes the Real-time counter interrupt state to pending; read: Real-time counter interrupt is pending

End of enumeration elements list.

SETPEND21 : no description available
bits : 21 - 21 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Analog comparator 1 interrupt interrupt is not pending

#1 : 1

write: changes the Analog comparator 1 interrupt interrupt state to pending; read: Analog comparator 1 interrupt interrupt is pending

End of enumeration elements list.

SETPEND22 : no description available
bits : 22 - 22 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Periodic timer overflow channel 0 interrupt is not pending

#1 : 1

write: changes the Periodic timer overflow channel 0 interrupt state to pending; read: Periodic timer overflow channel 0 interrupt is pending

End of enumeration elements list.

SETPEND23 : no description available
bits : 23 - 23 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Periodic timer overflow channel 1 interrupt is not pending

#1 : 1

write: changes the Periodic timer overflow channel 1 interrupt state to pending; read: Periodic timer overflow channel 1 interrupt is pending

End of enumeration elements list.

SETPEND24 : no description available
bits : 24 - 24 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Keyboard interrupt interrupt is not pending

#1 : 1

write: changes the Keyboard interrupt interrupt state to pending; read: Keyboard interrupt interrupt is pending

End of enumeration elements list.

SETPEND25 : no description available
bits : 25 - 25 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Keyboard interrupt interrupt is not pending

#1 : 1

write: changes the Keyboard interrupt interrupt state to pending; read: Keyboard interrupt interrupt is pending

End of enumeration elements list.

SETPEND26 : no description available
bits : 26 - 26 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Reserved iv 42 interrupt is not pending

#1 : 1

write: changes the Reserved iv 42 interrupt state to pending; read: Reserved iv 42 interrupt is pending

End of enumeration elements list.

SETPEND27 : no description available
bits : 27 - 27 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Clock loss of lock interrupt is not pending

#1 : 1

write: changes the Clock loss of lock interrupt state to pending; read: Clock loss of lock interrupt is pending

End of enumeration elements list.

SETPEND28 : no description available
bits : 28 - 28 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: WDOG interrupt is not pending

#1 : 1

write: changes the WDOG interrupt state to pending; read: WDOG interrupt is pending

End of enumeration elements list.

SETPEND29 : no description available
bits : 29 - 29 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Pulse width timer interrupt is not pending

#1 : 1

write: changes the Pulse width timer interrupt state to pending; read: Pulse width timer interrupt is pending

End of enumeration elements list.

SETPEND30 : no description available
bits : 30 - 30 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Freescale's Scalable Controller Area Network Rx interrupt is not pending

#1 : 1

write: changes the Freescale's Scalable Controller Area Network Rx interrupt state to pending; read: Freescale's Scalable Controller Area Network Rx interrupt is pending

End of enumeration elements list.

SETPEND31 : no description available
bits : 31 - 31 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Freescale's Scalable Controller Area Network Tx and error interrupt is not pending

#1 : 1

write: changes the Freescale's Scalable Controller Area Network Tx and error interrupt state to pending; read: Freescale's Scalable Controller Area Network Tx and error interrupt is pending

End of enumeration elements list.


ICPR

Interrupt Clear Pending Register
address_offset : 0x180 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

ICPR ICPR read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 CLRPEND0 CLRPEND1 CLRPEND2 CLRPEND3 CLRPEND4 CLRPEND5 CLRPEND6 CLRPEND7 CLRPEND8 CLRPEND9 CLRPEND10 CLRPEND11 CLRPEND12 CLRPEND13 CLRPEND14 CLRPEND15 CLRPEND16 CLRPEND17 CLRPEND18 CLRPEND19 CLRPEND20 CLRPEND21 CLRPEND22 CLRPEND23 CLRPEND24 CLRPEND25 CLRPEND26 CLRPEND27 CLRPEND28 CLRPEND29 CLRPEND30 CLRPEND31

CLRPEND0 : no description available
bits : 0 - 0 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Reserved iv 16 interrupt is not pending

#1 : 1

write: removes pending state from the Reserved iv 16 interrupt; read: Reserved iv 16 interrupt is pending

End of enumeration elements list.

CLRPEND1 : no description available
bits : 1 - 1 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Reserved iv 17 interrupt is not pending

#1 : 1

write: removes pending state from the Reserved iv 17 interrupt; read: Reserved iv 17 interrupt is pending

End of enumeration elements list.

CLRPEND2 : no description available
bits : 2 - 2 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Reserved iv 18 interrupt is not pending

#1 : 1

write: removes pending state from the Reserved iv 18 interrupt; read: Reserved iv 18 interrupt is pending

End of enumeration elements list.

CLRPEND3 : no description available
bits : 3 - 3 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Reserved iv 19 interrupt is not pending

#1 : 1

write: removes pending state from the Reserved iv 19 interrupt; read: Reserved iv 19 interrupt is pending

End of enumeration elements list.

CLRPEND4 : no description available
bits : 4 - 4 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Reserved iv 20 interrupt is not pending

#1 : 1

write: removes pending state from the Reserved iv 20 interrupt; read: Reserved iv 20 interrupt is pending

End of enumeration elements list.

CLRPEND5 : no description available
bits : 5 - 5 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Command complete and read collision interrupt is not pending

#1 : 1

write: removes pending state from the Command complete and read collision interrupt; read: Command complete and read collision interrupt is pending

End of enumeration elements list.

CLRPEND6 : no description available
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Low-voltage detect, low-voltage warning interrupt is not pending

#1 : 1

write: removes pending state from the Low-voltage detect, low-voltage warning interrupt; read: Low-voltage detect, low-voltage warning interrupt is pending

End of enumeration elements list.

CLRPEND7 : no description available
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: External Interrupt interrupt is not pending

#1 : 1

write: removes pending state from the External Interrupt interrupt; read: External Interrupt interrupt is pending

End of enumeration elements list.

CLRPEND8 : no description available
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Inter-Integrated Circuit 0 interrupt is not pending

#1 : 1

write: removes pending state from the Inter-Integrated Circuit 0 interrupt; read: Inter-Integrated Circuit 0 interrupt is pending

End of enumeration elements list.

CLRPEND9 : no description available
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Inter-Integrated Circuit 1 interrupt is not pending

#1 : 1

write: removes pending state from the Inter-Integrated Circuit 1 interrupt; read: Inter-Integrated Circuit 1 interrupt is pending

End of enumeration elements list.

CLRPEND10 : no description available
bits : 10 - 10 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Serial Peripheral Interface 0 interrupt is not pending

#1 : 1

write: removes pending state from the Serial Peripheral Interface 0 interrupt; read: Serial Peripheral Interface 0 interrupt is pending

End of enumeration elements list.

CLRPEND11 : no description available
bits : 11 - 11 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Serial Peripheral Interface 1 interrupt is not pending

#1 : 1

write: removes pending state from the Serial Peripheral Interface 1 interrupt; read: Serial Peripheral Interface 1 interrupt is pending

End of enumeration elements list.

CLRPEND12 : no description available
bits : 12 - 12 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: UART0 status and error interrupt is not pending

#1 : 1

write: removes pending state from the UART0 status and error interrupt; read: UART0 status and error interrupt is pending

End of enumeration elements list.

CLRPEND13 : no description available
bits : 13 - 13 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: UART1 status and error interrupt is not pending

#1 : 1

write: removes pending state from the UART1 status and error interrupt; read: UART1 status and error interrupt is pending

End of enumeration elements list.

CLRPEND14 : no description available
bits : 14 - 14 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: UART2 status and error interrupt is not pending

#1 : 1

write: removes pending state from the UART2 status and error interrupt; read: UART2 status and error interrupt is pending

End of enumeration elements list.

CLRPEND15 : no description available
bits : 15 - 15 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Analog-to-Digital Converter 0 interrupt is not pending

#1 : 1

write: removes pending state from the Analog-to-Digital Converter 0 interrupt; read: Analog-to-Digital Converter 0 interrupt is pending

End of enumeration elements list.

CLRPEND16 : no description available
bits : 16 - 16 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Analog comparator 0 interrupt interrupt is not pending

#1 : 1

write: removes pending state from the Analog comparator 0 interrupt interrupt; read: Analog comparator 0 interrupt interrupt is pending

End of enumeration elements list.

CLRPEND17 : no description available
bits : 17 - 17 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: FlexTimer Module 0 interrupt is not pending

#1 : 1

write: removes pending state from the FlexTimer Module 0 interrupt; read: FlexTimer Module 0 interrupt is pending

End of enumeration elements list.

CLRPEND18 : no description available
bits : 18 - 18 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: FlexTimer Module 1 interrupt is not pending

#1 : 1

write: removes pending state from the FlexTimer Module 1 interrupt; read: FlexTimer Module 1 interrupt is pending

End of enumeration elements list.

CLRPEND19 : no description available
bits : 19 - 19 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: FlexTimer Module 2 interrupt is not pending

#1 : 1

write: removes pending state from the FlexTimer Module 2 interrupt; read: FlexTimer Module 2 interrupt is pending

End of enumeration elements list.

CLRPEND20 : no description available
bits : 20 - 20 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Real-time counter interrupt is not pending

#1 : 1

write: removes pending state from the Real-time counter interrupt; read: Real-time counter interrupt is pending

End of enumeration elements list.

CLRPEND21 : no description available
bits : 21 - 21 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Analog comparator 1 interrupt interrupt is not pending

#1 : 1

write: removes pending state from the Analog comparator 1 interrupt interrupt; read: Analog comparator 1 interrupt interrupt is pending

End of enumeration elements list.

CLRPEND22 : no description available
bits : 22 - 22 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Periodic timer overflow channel 0 interrupt is not pending

#1 : 1

write: removes pending state from the Periodic timer overflow channel 0 interrupt; read: Periodic timer overflow channel 0 interrupt is pending

End of enumeration elements list.

CLRPEND23 : no description available
bits : 23 - 23 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Periodic timer overflow channel 1 interrupt is not pending

#1 : 1

write: removes pending state from the Periodic timer overflow channel 1 interrupt; read: Periodic timer overflow channel 1 interrupt is pending

End of enumeration elements list.

CLRPEND24 : no description available
bits : 24 - 24 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Keyboard interrupt interrupt is not pending

#1 : 1

write: removes pending state from the Keyboard interrupt interrupt; read: Keyboard interrupt interrupt is pending

End of enumeration elements list.

CLRPEND25 : no description available
bits : 25 - 25 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Keyboard interrupt interrupt is not pending

#1 : 1

write: removes pending state from the Keyboard interrupt interrupt; read: Keyboard interrupt interrupt is pending

End of enumeration elements list.

CLRPEND26 : no description available
bits : 26 - 26 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Reserved iv 42 interrupt is not pending

#1 : 1

write: removes pending state from the Reserved iv 42 interrupt; read: Reserved iv 42 interrupt is pending

End of enumeration elements list.

CLRPEND27 : no description available
bits : 27 - 27 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Clock loss of lock interrupt is not pending

#1 : 1

write: removes pending state from the Clock loss of lock interrupt; read: Clock loss of lock interrupt is pending

End of enumeration elements list.

CLRPEND28 : no description available
bits : 28 - 28 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: WDOG interrupt is not pending

#1 : 1

write: removes pending state from the WDOG interrupt; read: WDOG interrupt is pending

End of enumeration elements list.

CLRPEND29 : no description available
bits : 29 - 29 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Pulse width timer interrupt is not pending

#1 : 1

write: removes pending state from the Pulse width timer interrupt; read: Pulse width timer interrupt is pending

End of enumeration elements list.

CLRPEND30 : no description available
bits : 30 - 30 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Freescale's Scalable Controller Area Network Rx interrupt is not pending

#1 : 1

write: removes pending state from the Freescale's Scalable Controller Area Network Rx interrupt; read: Freescale's Scalable Controller Area Network Rx interrupt is pending

End of enumeration elements list.

CLRPEND31 : no description available
bits : 31 - 31 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Freescale's Scalable Controller Area Network Tx and error interrupt is not pending

#1 : 1

write: removes pending state from the Freescale's Scalable Controller Area Network Tx and error interrupt; read: Freescale's Scalable Controller Area Network Tx and error interrupt is pending

End of enumeration elements list.


IPR0

Interrupt Priority Register 0
address_offset : 0x300 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

IPR0 IPR0 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 PRI_0 PRI_1 PRI_2 PRI_3

PRI_0 : Priority of the Reserved iv 16 interrupt
bits : 6 - 7 (2 bit)
access : read-write

PRI_1 : Priority of the Reserved iv 17 interrupt
bits : 14 - 15 (2 bit)
access : read-write

PRI_2 : Priority of the Reserved iv 18 interrupt
bits : 22 - 23 (2 bit)
access : read-write

PRI_3 : Priority of the Reserved iv 19 interrupt
bits : 30 - 31 (2 bit)
access : read-write


IPR1

Interrupt Priority Register 1
address_offset : 0x304 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

IPR1 IPR1 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 PRI_4 PRI_5 PRI_6 PRI_7

PRI_4 : Priority of the Reserved iv 20 interrupt
bits : 6 - 7 (2 bit)
access : read-write

PRI_5 : Priority of the Command complete and read collision interrupt
bits : 14 - 15 (2 bit)
access : read-write

PRI_6 : Priority of the Low-voltage detect, low-voltage warning interrupt
bits : 22 - 23 (2 bit)
access : read-write

PRI_7 : Priority of the External Interrupt interrupt
bits : 30 - 31 (2 bit)
access : read-write


IPR2

Interrupt Priority Register 2
address_offset : 0x308 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

IPR2 IPR2 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 PRI_8 PRI_9 PRI_10 PRI_11

PRI_8 : Priority of the Inter-Integrated Circuit 0 interrupt
bits : 6 - 7 (2 bit)
access : read-write

PRI_9 : Priority of the Inter-Integrated Circuit 1 interrupt
bits : 14 - 15 (2 bit)
access : read-write

PRI_10 : Priority of the Serial Peripheral Interface 0 interrupt
bits : 22 - 23 (2 bit)
access : read-write

PRI_11 : Priority of the Serial Peripheral Interface 1 interrupt
bits : 30 - 31 (2 bit)
access : read-write


IPR3

Interrupt Priority Register 3
address_offset : 0x30C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

IPR3 IPR3 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 PRI_12 PRI_13 PRI_14 PRI_15

PRI_12 : Priority of the UART0 status and error interrupt
bits : 6 - 7 (2 bit)
access : read-write

PRI_13 : Priority of the UART1 status and error interrupt
bits : 14 - 15 (2 bit)
access : read-write

PRI_14 : Priority of the UART2 status and error interrupt
bits : 22 - 23 (2 bit)
access : read-write

PRI_15 : Priority of the Analog-to-Digital Converter 0 interrupt
bits : 30 - 31 (2 bit)
access : read-write


IPR4

Interrupt Priority Register 4
address_offset : 0x310 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

IPR4 IPR4 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 PRI_16 PRI_17 PRI_18 PRI_19

PRI_16 : Priority of the Analog comparator 0 interrupt interrupt
bits : 6 - 7 (2 bit)
access : read-write

PRI_17 : Priority of the FlexTimer Module 0 interrupt
bits : 14 - 15 (2 bit)
access : read-write

PRI_18 : Priority of the FlexTimer Module 1 interrupt
bits : 22 - 23 (2 bit)
access : read-write

PRI_19 : Priority of the FlexTimer Module 2 interrupt
bits : 30 - 31 (2 bit)
access : read-write


IPR5

Interrupt Priority Register 5
address_offset : 0x314 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

IPR5 IPR5 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 PRI_20 PRI_21 PRI_22 PRI_23

PRI_20 : Priority of the Real-time counter interrupt
bits : 6 - 7 (2 bit)
access : read-write

PRI_21 : Priority of the Analog comparator 1 interrupt interrupt
bits : 14 - 15 (2 bit)
access : read-write

PRI_22 : Priority of the Periodic timer overflow channel 0 interrupt
bits : 22 - 23 (2 bit)
access : read-write

PRI_23 : Priority of the Periodic timer overflow channel 1 interrupt
bits : 30 - 31 (2 bit)
access : read-write


IPR6

Interrupt Priority Register 6
address_offset : 0x318 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

IPR6 IPR6 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 PRI_24 PRI_25 PRI_26 PRI_27

PRI_24 : Priority of the Keyboard interrupt interrupt
bits : 6 - 7 (2 bit)
access : read-write

PRI_25 : Priority of the Keyboard interrupt interrupt
bits : 14 - 15 (2 bit)
access : read-write

PRI_26 : Priority of the Reserved iv 42 interrupt
bits : 22 - 23 (2 bit)
access : read-write

PRI_27 : Priority of the Clock loss of lock interrupt
bits : 30 - 31 (2 bit)
access : read-write


IPR7

Interrupt Priority Register 7
address_offset : 0x31C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

IPR7 IPR7 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 PRI_28 PRI_29 PRI_30 PRI_31

PRI_28 : Priority of the WDOG interrupt
bits : 6 - 7 (2 bit)
access : read-write

PRI_29 : Priority of the Pulse width timer interrupt
bits : 14 - 15 (2 bit)
access : read-write

PRI_30 : Priority of the Freescale's Scalable Controller Area Network Rx interrupt
bits : 22 - 23 (2 bit)
access : read-write

PRI_31 : Priority of the Freescale's Scalable Controller Area Network Tx and error interrupt
bits : 30 - 31 (2 bit)
access : read-write


ICER

Interrupt Clear Enable Register
address_offset : 0x80 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

ICER ICER read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 CLRENA0 CLRENA1 CLRENA2 CLRENA3 CLRENA4 CLRENA5 CLRENA6 CLRENA7 CLRENA8 CLRENA9 CLRENA10 CLRENA11 CLRENA12 CLRENA13 CLRENA14 CLRENA15 CLRENA16 CLRENA17 CLRENA18 CLRENA19 CLRENA20 CLRENA21 CLRENA22 CLRENA23 CLRENA24 CLRENA25 CLRENA26 CLRENA27 CLRENA28 CLRENA29 CLRENA30 CLRENA31

CLRENA0 : no description available
bits : 0 - 0 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Reserved iv 16 interrupt disabled

#1 : 1

write: disable Reserved iv 16 interrupt; read: Reserved iv 16 interrupt enabled

End of enumeration elements list.

CLRENA1 : no description available
bits : 1 - 1 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Reserved iv 17 interrupt disabled

#1 : 1

write: disable Reserved iv 17 interrupt; read: Reserved iv 17 interrupt enabled

End of enumeration elements list.

CLRENA2 : no description available
bits : 2 - 2 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Reserved iv 18 interrupt disabled

#1 : 1

write: disable Reserved iv 18 interrupt; read: Reserved iv 18 interrupt enabled

End of enumeration elements list.

CLRENA3 : no description available
bits : 3 - 3 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Reserved iv 19 interrupt disabled

#1 : 1

write: disable Reserved iv 19 interrupt; read: Reserved iv 19 interrupt enabled

End of enumeration elements list.

CLRENA4 : no description available
bits : 4 - 4 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Reserved iv 20 interrupt disabled

#1 : 1

write: disable Reserved iv 20 interrupt; read: Reserved iv 20 interrupt enabled

End of enumeration elements list.

CLRENA5 : no description available
bits : 5 - 5 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Command complete and read collision interrupt disabled

#1 : 1

write: disable Command complete and read collision interrupt; read: Command complete and read collision interrupt enabled

End of enumeration elements list.

CLRENA6 : no description available
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Low-voltage detect, low-voltage warning interrupt disabled

#1 : 1

write: disable Low-voltage detect, low-voltage warning interrupt; read: Low-voltage detect, low-voltage warning interrupt enabled

End of enumeration elements list.

CLRENA7 : no description available
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: External Interrupt interrupt disabled

#1 : 1

write: disable External Interrupt interrupt; read: External Interrupt interrupt enabled

End of enumeration elements list.

CLRENA8 : no description available
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Inter-Integrated Circuit 0 interrupt disabled

#1 : 1

write: disable Inter-Integrated Circuit 0 interrupt; read: Inter-Integrated Circuit 0 interrupt enabled

End of enumeration elements list.

CLRENA9 : no description available
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Inter-Integrated Circuit 1 interrupt disabled

#1 : 1

write: disable Inter-Integrated Circuit 1 interrupt; read: Inter-Integrated Circuit 1 interrupt enabled

End of enumeration elements list.

CLRENA10 : no description available
bits : 10 - 10 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Serial Peripheral Interface 0 interrupt disabled

#1 : 1

write: disable Serial Peripheral Interface 0 interrupt; read: Serial Peripheral Interface 0 interrupt enabled

End of enumeration elements list.

CLRENA11 : no description available
bits : 11 - 11 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Serial Peripheral Interface 1 interrupt disabled

#1 : 1

write: disable Serial Peripheral Interface 1 interrupt; read: Serial Peripheral Interface 1 interrupt enabled

End of enumeration elements list.

CLRENA12 : no description available
bits : 12 - 12 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: UART0 status and error interrupt disabled

#1 : 1

write: disable UART0 status and error interrupt; read: UART0 status and error interrupt enabled

End of enumeration elements list.

CLRENA13 : no description available
bits : 13 - 13 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: UART1 status and error interrupt disabled

#1 : 1

write: disable UART1 status and error interrupt; read: UART1 status and error interrupt enabled

End of enumeration elements list.

CLRENA14 : no description available
bits : 14 - 14 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: UART2 status and error interrupt disabled

#1 : 1

write: disable UART2 status and error interrupt; read: UART2 status and error interrupt enabled

End of enumeration elements list.

CLRENA15 : no description available
bits : 15 - 15 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Analog-to-Digital Converter 0 interrupt disabled

#1 : 1

write: disable Analog-to-Digital Converter 0 interrupt; read: Analog-to-Digital Converter 0 interrupt enabled

End of enumeration elements list.

CLRENA16 : no description available
bits : 16 - 16 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Analog comparator 0 interrupt interrupt disabled

#1 : 1

write: disable Analog comparator 0 interrupt interrupt; read: Analog comparator 0 interrupt interrupt enabled

End of enumeration elements list.

CLRENA17 : no description available
bits : 17 - 17 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: FlexTimer Module 0 interrupt disabled

#1 : 1

write: disable FlexTimer Module 0 interrupt; read: FlexTimer Module 0 interrupt enabled

End of enumeration elements list.

CLRENA18 : no description available
bits : 18 - 18 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: FlexTimer Module 1 interrupt disabled

#1 : 1

write: disable FlexTimer Module 1 interrupt; read: FlexTimer Module 1 interrupt enabled

End of enumeration elements list.

CLRENA19 : no description available
bits : 19 - 19 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: FlexTimer Module 2 interrupt disabled

#1 : 1

write: disable FlexTimer Module 2 interrupt; read: FlexTimer Module 2 interrupt enabled

End of enumeration elements list.

CLRENA20 : no description available
bits : 20 - 20 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Real-time counter interrupt disabled

#1 : 1

write: disable Real-time counter interrupt; read: Real-time counter interrupt enabled

End of enumeration elements list.

CLRENA21 : no description available
bits : 21 - 21 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Analog comparator 1 interrupt interrupt disabled

#1 : 1

write: disable Analog comparator 1 interrupt interrupt; read: Analog comparator 1 interrupt interrupt enabled

End of enumeration elements list.

CLRENA22 : no description available
bits : 22 - 22 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Periodic timer overflow channel 0 interrupt disabled

#1 : 1

write: disable Periodic timer overflow channel 0 interrupt; read: Periodic timer overflow channel 0 interrupt enabled

End of enumeration elements list.

CLRENA23 : no description available
bits : 23 - 23 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Periodic timer overflow channel 1 interrupt disabled

#1 : 1

write: disable Periodic timer overflow channel 1 interrupt; read: Periodic timer overflow channel 1 interrupt enabled

End of enumeration elements list.

CLRENA24 : no description available
bits : 24 - 24 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Keyboard interrupt interrupt disabled

#1 : 1

write: disable Keyboard interrupt interrupt; read: Keyboard interrupt interrupt enabled

End of enumeration elements list.

CLRENA25 : no description available
bits : 25 - 25 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Keyboard interrupt interrupt disabled

#1 : 1

write: disable Keyboard interrupt interrupt; read: Keyboard interrupt interrupt enabled

End of enumeration elements list.

CLRENA26 : no description available
bits : 26 - 26 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Reserved iv 42 interrupt disabled

#1 : 1

write: disable Reserved iv 42 interrupt; read: Reserved iv 42 interrupt enabled

End of enumeration elements list.

CLRENA27 : no description available
bits : 27 - 27 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Clock loss of lock interrupt disabled

#1 : 1

write: disable Clock loss of lock interrupt; read: Clock loss of lock interrupt enabled

End of enumeration elements list.

CLRENA28 : no description available
bits : 28 - 28 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: WDOG interrupt disabled

#1 : 1

write: disable WDOG interrupt; read: WDOG interrupt enabled

End of enumeration elements list.

CLRENA29 : no description available
bits : 29 - 29 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Pulse width timer interrupt disabled

#1 : 1

write: disable Pulse width timer interrupt; read: Pulse width timer interrupt enabled

End of enumeration elements list.

CLRENA30 : no description available
bits : 30 - 30 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Freescale's Scalable Controller Area Network Rx interrupt disabled

#1 : 1

write: disable Freescale's Scalable Controller Area Network Rx interrupt; read: Freescale's Scalable Controller Area Network Rx interrupt enabled

End of enumeration elements list.

CLRENA31 : no description available
bits : 31 - 31 (1 bit)
access : read-write

Enumeration:

#0 : 0

write: no effect; read: Freescale's Scalable Controller Area Network Tx and error interrupt disabled

#1 : 1

write: disable Freescale's Scalable Controller Area Network Tx and error interrupt; read: Freescale's Scalable Controller Area Network Tx and error interrupt enabled

End of enumeration elements list.



Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !

This website is sponsored by EmbeetleEmbeetle, an IDE designed from scratch for embedded software developers.