Embeetle, an IDE designed from scratch for embedded software developers.address_offset : 0x0 Bytes (0x0)
size : 0x1000 byte (0x0)
mem_usage : registers
protection : not protected
Description collection: Configuration of GPIO pins
address_offset : 0x1504 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DIR : Pin direction. Same physical register as DIR register
bits : 0 - -1 (0 bit)
Enumeration:
0 : Input
Configure pin as an input pin
1 : Output
Configure pin as an output pin
End of enumeration elements list.
INPUT : Connect or disconnect input buffer
bits : 1 - 0 (0 bit)
Enumeration:
0 : Connect
Connect input buffer
1 : Disconnect
Disconnect input buffer
End of enumeration elements list.
PULL : Pull configuration
bits : 2 - 2 (1 bit)
Enumeration:
0 : Disabled
No pull
1 : Pulldown
Pull down on pin
3 : Pullup
Pull up on pin
End of enumeration elements list.
DRIVE : Drive configuration
bits : 8 - 9 (2 bit)
Enumeration:
0 : S0S1
Standard '0', standard '1'
1 : H0S1
High drive '0', standard '1'
2 : S0H1
Standard '0', high drive '1'
3 : H0H1
High drive '0', high 'drive '1''
4 : D0S1
Disconnect '0' standard '1' (normally used for wired-or connections)
5 : D0H1
Disconnect '0', high drive '1' (normally used for wired-or connections)
6 : S0D1
Standard '0'. disconnect '1' (normally used for wired-and connections)
7 : H0D1
High drive '0', disconnect '1' (normally used for wired-and connections)
End of enumeration elements list.
SENSE : Pin sensing mechanism
bits : 16 - 16 (1 bit)
Enumeration:
0 : Disabled
Disabled
2 : High
Sense for high level
3 : Low
Sense for low level
End of enumeration elements list.
Description collection: Configuration of GPIO pins
address_offset : 0x1C0C Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DIR : Pin direction. Same physical register as DIR register
bits : 0 - -1 (0 bit)
Enumeration:
0 : Input
Configure pin as an input pin
1 : Output
Configure pin as an output pin
End of enumeration elements list.
INPUT : Connect or disconnect input buffer
bits : 1 - 0 (0 bit)
Enumeration:
0 : Connect
Connect input buffer
1 : Disconnect
Disconnect input buffer
End of enumeration elements list.
PULL : Pull configuration
bits : 2 - 2 (1 bit)
Enumeration:
0 : Disabled
No pull
1 : Pulldown
Pull down on pin
3 : Pullup
Pull up on pin
End of enumeration elements list.
DRIVE : Drive configuration
bits : 8 - 9 (2 bit)
Enumeration:
0 : S0S1
Standard '0', standard '1'
1 : H0S1
High drive '0', standard '1'
2 : S0H1
Standard '0', high drive '1'
3 : H0H1
High drive '0', high 'drive '1''
4 : D0S1
Disconnect '0' standard '1' (normally used for wired-or connections)
5 : D0H1
Disconnect '0', high drive '1' (normally used for wired-or connections)
6 : S0D1
Standard '0'. disconnect '1' (normally used for wired-and connections)
7 : H0D1
High drive '0', disconnect '1' (normally used for wired-and connections)
End of enumeration elements list.
SENSE : Pin sensing mechanism
bits : 16 - 16 (1 bit)
Enumeration:
0 : Disabled
Disabled
2 : High
Sense for high level
3 : Low
Sense for low level
End of enumeration elements list.
Description collection: Configuration of GPIO pins
address_offset : 0x2318 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DIR : Pin direction. Same physical register as DIR register
bits : 0 - -1 (0 bit)
Enumeration:
0 : Input
Configure pin as an input pin
1 : Output
Configure pin as an output pin
End of enumeration elements list.
INPUT : Connect or disconnect input buffer
bits : 1 - 0 (0 bit)
Enumeration:
0 : Connect
Connect input buffer
1 : Disconnect
Disconnect input buffer
End of enumeration elements list.
PULL : Pull configuration
bits : 2 - 2 (1 bit)
Enumeration:
0 : Disabled
No pull
1 : Pulldown
Pull down on pin
3 : Pullup
Pull up on pin
End of enumeration elements list.
DRIVE : Drive configuration
bits : 8 - 9 (2 bit)
Enumeration:
0 : S0S1
Standard '0', standard '1'
1 : H0S1
High drive '0', standard '1'
2 : S0H1
Standard '0', high drive '1'
3 : H0H1
High drive '0', high 'drive '1''
4 : D0S1
Disconnect '0' standard '1' (normally used for wired-or connections)
5 : D0H1
Disconnect '0', high drive '1' (normally used for wired-or connections)
6 : S0D1
Standard '0'. disconnect '1' (normally used for wired-and connections)
7 : H0D1
High drive '0', disconnect '1' (normally used for wired-and connections)
End of enumeration elements list.
SENSE : Pin sensing mechanism
bits : 16 - 16 (1 bit)
Enumeration:
0 : Disabled
Disabled
2 : High
Sense for high level
3 : Low
Sense for low level
End of enumeration elements list.
Description collection: Configuration of GPIO pins
address_offset : 0x2A28 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DIR : Pin direction. Same physical register as DIR register
bits : 0 - -1 (0 bit)
Enumeration:
0 : Input
Configure pin as an input pin
1 : Output
Configure pin as an output pin
End of enumeration elements list.
INPUT : Connect or disconnect input buffer
bits : 1 - 0 (0 bit)
Enumeration:
0 : Connect
Connect input buffer
1 : Disconnect
Disconnect input buffer
End of enumeration elements list.
PULL : Pull configuration
bits : 2 - 2 (1 bit)
Enumeration:
0 : Disabled
No pull
1 : Pulldown
Pull down on pin
3 : Pullup
Pull up on pin
End of enumeration elements list.
DRIVE : Drive configuration
bits : 8 - 9 (2 bit)
Enumeration:
0 : S0S1
Standard '0', standard '1'
1 : H0S1
High drive '0', standard '1'
2 : S0H1
Standard '0', high drive '1'
3 : H0H1
High drive '0', high 'drive '1''
4 : D0S1
Disconnect '0' standard '1' (normally used for wired-or connections)
5 : D0H1
Disconnect '0', high drive '1' (normally used for wired-or connections)
6 : S0D1
Standard '0'. disconnect '1' (normally used for wired-and connections)
7 : H0D1
High drive '0', disconnect '1' (normally used for wired-and connections)
End of enumeration elements list.
SENSE : Pin sensing mechanism
bits : 16 - 16 (1 bit)
Enumeration:
0 : Disabled
Disabled
2 : High
Sense for high level
3 : Low
Sense for low level
End of enumeration elements list.
Description collection: Configuration of GPIO pins
address_offset : 0x313C Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DIR : Pin direction. Same physical register as DIR register
bits : 0 - -1 (0 bit)
Enumeration:
0 : Input
Configure pin as an input pin
1 : Output
Configure pin as an output pin
End of enumeration elements list.
INPUT : Connect or disconnect input buffer
bits : 1 - 0 (0 bit)
Enumeration:
0 : Connect
Connect input buffer
1 : Disconnect
Disconnect input buffer
End of enumeration elements list.
PULL : Pull configuration
bits : 2 - 2 (1 bit)
Enumeration:
0 : Disabled
No pull
1 : Pulldown
Pull down on pin
3 : Pullup
Pull up on pin
End of enumeration elements list.
DRIVE : Drive configuration
bits : 8 - 9 (2 bit)
Enumeration:
0 : S0S1
Standard '0', standard '1'
1 : H0S1
High drive '0', standard '1'
2 : S0H1
Standard '0', high drive '1'
3 : H0H1
High drive '0', high 'drive '1''
4 : D0S1
Disconnect '0' standard '1' (normally used for wired-or connections)
5 : D0H1
Disconnect '0', high drive '1' (normally used for wired-or connections)
6 : S0D1
Standard '0'. disconnect '1' (normally used for wired-and connections)
7 : H0D1
High drive '0', disconnect '1' (normally used for wired-and connections)
End of enumeration elements list.
SENSE : Pin sensing mechanism
bits : 16 - 16 (1 bit)
Enumeration:
0 : Disabled
Disabled
2 : High
Sense for high level
3 : Low
Sense for low level
End of enumeration elements list.
Description collection: Configuration of GPIO pins
address_offset : 0x3854 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DIR : Pin direction. Same physical register as DIR register
bits : 0 - -1 (0 bit)
Enumeration:
0 : Input
Configure pin as an input pin
1 : Output
Configure pin as an output pin
End of enumeration elements list.
INPUT : Connect or disconnect input buffer
bits : 1 - 0 (0 bit)
Enumeration:
0 : Connect
Connect input buffer
1 : Disconnect
Disconnect input buffer
End of enumeration elements list.
PULL : Pull configuration
bits : 2 - 2 (1 bit)
Enumeration:
0 : Disabled
No pull
1 : Pulldown
Pull down on pin
3 : Pullup
Pull up on pin
End of enumeration elements list.
DRIVE : Drive configuration
bits : 8 - 9 (2 bit)
Enumeration:
0 : S0S1
Standard '0', standard '1'
1 : H0S1
High drive '0', standard '1'
2 : S0H1
Standard '0', high drive '1'
3 : H0H1
High drive '0', high 'drive '1''
4 : D0S1
Disconnect '0' standard '1' (normally used for wired-or connections)
5 : D0H1
Disconnect '0', high drive '1' (normally used for wired-or connections)
6 : S0D1
Standard '0'. disconnect '1' (normally used for wired-and connections)
7 : H0D1
High drive '0', disconnect '1' (normally used for wired-and connections)
End of enumeration elements list.
SENSE : Pin sensing mechanism
bits : 16 - 16 (1 bit)
Enumeration:
0 : Disabled
Disabled
2 : High
Sense for high level
3 : Low
Sense for low level
End of enumeration elements list.
Description collection: Configuration of GPIO pins
address_offset : 0x3F70 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DIR : Pin direction. Same physical register as DIR register
bits : 0 - -1 (0 bit)
Enumeration:
0 : Input
Configure pin as an input pin
1 : Output
Configure pin as an output pin
End of enumeration elements list.
INPUT : Connect or disconnect input buffer
bits : 1 - 0 (0 bit)
Enumeration:
0 : Connect
Connect input buffer
1 : Disconnect
Disconnect input buffer
End of enumeration elements list.
PULL : Pull configuration
bits : 2 - 2 (1 bit)
Enumeration:
0 : Disabled
No pull
1 : Pulldown
Pull down on pin
3 : Pullup
Pull up on pin
End of enumeration elements list.
DRIVE : Drive configuration
bits : 8 - 9 (2 bit)
Enumeration:
0 : S0S1
Standard '0', standard '1'
1 : H0S1
High drive '0', standard '1'
2 : S0H1
Standard '0', high drive '1'
3 : H0H1
High drive '0', high 'drive '1''
4 : D0S1
Disconnect '0' standard '1' (normally used for wired-or connections)
5 : D0H1
Disconnect '0', high drive '1' (normally used for wired-or connections)
6 : S0D1
Standard '0'. disconnect '1' (normally used for wired-and connections)
7 : H0D1
High drive '0', disconnect '1' (normally used for wired-and connections)
End of enumeration elements list.
SENSE : Pin sensing mechanism
bits : 16 - 16 (1 bit)
Enumeration:
0 : Disabled
Disabled
2 : High
Sense for high level
3 : Low
Sense for low level
End of enumeration elements list.
Description collection: Configuration of GPIO pins
address_offset : 0x4690 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DIR : Pin direction. Same physical register as DIR register
bits : 0 - -1 (0 bit)
Enumeration:
0 : Input
Configure pin as an input pin
1 : Output
Configure pin as an output pin
End of enumeration elements list.
INPUT : Connect or disconnect input buffer
bits : 1 - 0 (0 bit)
Enumeration:
0 : Connect
Connect input buffer
1 : Disconnect
Disconnect input buffer
End of enumeration elements list.
PULL : Pull configuration
bits : 2 - 2 (1 bit)
Enumeration:
0 : Disabled
No pull
1 : Pulldown
Pull down on pin
3 : Pullup
Pull up on pin
End of enumeration elements list.
DRIVE : Drive configuration
bits : 8 - 9 (2 bit)
Enumeration:
0 : S0S1
Standard '0', standard '1'
1 : H0S1
High drive '0', standard '1'
2 : S0H1
Standard '0', high drive '1'
3 : H0H1
High drive '0', high 'drive '1''
4 : D0S1
Disconnect '0' standard '1' (normally used for wired-or connections)
5 : D0H1
Disconnect '0', high drive '1' (normally used for wired-or connections)
6 : S0D1
Standard '0'. disconnect '1' (normally used for wired-and connections)
7 : H0D1
High drive '0', disconnect '1' (normally used for wired-and connections)
End of enumeration elements list.
SENSE : Pin sensing mechanism
bits : 16 - 16 (1 bit)
Enumeration:
0 : Disabled
Disabled
2 : High
Sense for high level
3 : Low
Sense for low level
End of enumeration elements list.
Description collection: Configuration of GPIO pins
address_offset : 0x4DB4 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DIR : Pin direction. Same physical register as DIR register
bits : 0 - -1 (0 bit)
Enumeration:
0 : Input
Configure pin as an input pin
1 : Output
Configure pin as an output pin
End of enumeration elements list.
INPUT : Connect or disconnect input buffer
bits : 1 - 0 (0 bit)
Enumeration:
0 : Connect
Connect input buffer
1 : Disconnect
Disconnect input buffer
End of enumeration elements list.
PULL : Pull configuration
bits : 2 - 2 (1 bit)
Enumeration:
0 : Disabled
No pull
1 : Pulldown
Pull down on pin
3 : Pullup
Pull up on pin
End of enumeration elements list.
DRIVE : Drive configuration
bits : 8 - 9 (2 bit)
Enumeration:
0 : S0S1
Standard '0', standard '1'
1 : H0S1
High drive '0', standard '1'
2 : S0H1
Standard '0', high drive '1'
3 : H0H1
High drive '0', high 'drive '1''
4 : D0S1
Disconnect '0' standard '1' (normally used for wired-or connections)
5 : D0H1
Disconnect '0', high drive '1' (normally used for wired-or connections)
6 : S0D1
Standard '0'. disconnect '1' (normally used for wired-and connections)
7 : H0D1
High drive '0', disconnect '1' (normally used for wired-and connections)
End of enumeration elements list.
SENSE : Pin sensing mechanism
bits : 16 - 16 (1 bit)
Enumeration:
0 : Disabled
Disabled
2 : High
Sense for high level
3 : Low
Sense for low level
End of enumeration elements list.
Write GPIO port
address_offset : 0x504 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PIN0 : Pin 0
bits : 0 - -1 (0 bit)
Enumeration:
0 : Low
Pin driver is low
1 : High
Pin driver is high
End of enumeration elements list.
PIN1 : Pin 1
bits : 1 - 0 (0 bit)
Enumeration:
0 : Low
Pin driver is low
1 : High
Pin driver is high
End of enumeration elements list.
PIN2 : Pin 2
bits : 2 - 1 (0 bit)
Enumeration:
0 : Low
Pin driver is low
1 : High
Pin driver is high
End of enumeration elements list.
PIN3 : Pin 3
bits : 3 - 2 (0 bit)
Enumeration:
0 : Low
Pin driver is low
1 : High
Pin driver is high
End of enumeration elements list.
PIN4 : Pin 4
bits : 4 - 3 (0 bit)
Enumeration:
0 : Low
Pin driver is low
1 : High
Pin driver is high
End of enumeration elements list.
PIN5 : Pin 5
bits : 5 - 4 (0 bit)
Enumeration:
0 : Low
Pin driver is low
1 : High
Pin driver is high
End of enumeration elements list.
PIN6 : Pin 6
bits : 6 - 5 (0 bit)
Enumeration:
0 : Low
Pin driver is low
1 : High
Pin driver is high
End of enumeration elements list.
PIN7 : Pin 7
bits : 7 - 6 (0 bit)
Enumeration:
0 : Low
Pin driver is low
1 : High
Pin driver is high
End of enumeration elements list.
PIN8 : Pin 8
bits : 8 - 7 (0 bit)
Enumeration:
0 : Low
Pin driver is low
1 : High
Pin driver is high
End of enumeration elements list.
PIN9 : Pin 9
bits : 9 - 8 (0 bit)
Enumeration:
0 : Low
Pin driver is low
1 : High
Pin driver is high
End of enumeration elements list.
PIN10 : Pin 10
bits : 10 - 9 (0 bit)
Enumeration:
0 : Low
Pin driver is low
1 : High
Pin driver is high
End of enumeration elements list.
PIN11 : Pin 11
bits : 11 - 10 (0 bit)
Enumeration:
0 : Low
Pin driver is low
1 : High
Pin driver is high
End of enumeration elements list.
PIN12 : Pin 12
bits : 12 - 11 (0 bit)
Enumeration:
0 : Low
Pin driver is low
1 : High
Pin driver is high
End of enumeration elements list.
PIN13 : Pin 13
bits : 13 - 12 (0 bit)
Enumeration:
0 : Low
Pin driver is low
1 : High
Pin driver is high
End of enumeration elements list.
PIN14 : Pin 14
bits : 14 - 13 (0 bit)
Enumeration:
0 : Low
Pin driver is low
1 : High
Pin driver is high
End of enumeration elements list.
PIN15 : Pin 15
bits : 15 - 14 (0 bit)
Enumeration:
0 : Low
Pin driver is low
1 : High
Pin driver is high
End of enumeration elements list.
PIN16 : Pin 16
bits : 16 - 15 (0 bit)
Enumeration:
0 : Low
Pin driver is low
1 : High
Pin driver is high
End of enumeration elements list.
PIN17 : Pin 17
bits : 17 - 16 (0 bit)
Enumeration:
0 : Low
Pin driver is low
1 : High
Pin driver is high
End of enumeration elements list.
PIN18 : Pin 18
bits : 18 - 17 (0 bit)
Enumeration:
0 : Low
Pin driver is low
1 : High
Pin driver is high
End of enumeration elements list.
PIN19 : Pin 19
bits : 19 - 18 (0 bit)
Enumeration:
0 : Low
Pin driver is low
1 : High
Pin driver is high
End of enumeration elements list.
PIN20 : Pin 20
bits : 20 - 19 (0 bit)
Enumeration:
0 : Low
Pin driver is low
1 : High
Pin driver is high
End of enumeration elements list.
PIN21 : Pin 21
bits : 21 - 20 (0 bit)
Enumeration:
0 : Low
Pin driver is low
1 : High
Pin driver is high
End of enumeration elements list.
PIN22 : Pin 22
bits : 22 - 21 (0 bit)
Enumeration:
0 : Low
Pin driver is low
1 : High
Pin driver is high
End of enumeration elements list.
PIN23 : Pin 23
bits : 23 - 22 (0 bit)
Enumeration:
0 : Low
Pin driver is low
1 : High
Pin driver is high
End of enumeration elements list.
PIN24 : Pin 24
bits : 24 - 23 (0 bit)
Enumeration:
0 : Low
Pin driver is low
1 : High
Pin driver is high
End of enumeration elements list.
PIN25 : Pin 25
bits : 25 - 24 (0 bit)
Enumeration:
0 : Low
Pin driver is low
1 : High
Pin driver is high
End of enumeration elements list.
PIN26 : Pin 26
bits : 26 - 25 (0 bit)
Enumeration:
0 : Low
Pin driver is low
1 : High
Pin driver is high
End of enumeration elements list.
PIN27 : Pin 27
bits : 27 - 26 (0 bit)
Enumeration:
0 : Low
Pin driver is low
1 : High
Pin driver is high
End of enumeration elements list.
PIN28 : Pin 28
bits : 28 - 27 (0 bit)
Enumeration:
0 : Low
Pin driver is low
1 : High
Pin driver is high
End of enumeration elements list.
PIN29 : Pin 29
bits : 29 - 28 (0 bit)
Enumeration:
0 : Low
Pin driver is low
1 : High
Pin driver is high
End of enumeration elements list.
PIN30 : Pin 30
bits : 30 - 29 (0 bit)
Enumeration:
0 : Low
Pin driver is low
1 : High
Pin driver is high
End of enumeration elements list.
PIN31 : Pin 31
bits : 31 - 30 (0 bit)
Enumeration:
0 : Low
Pin driver is low
1 : High
Pin driver is high
End of enumeration elements list.
Set individual bits in GPIO port
address_offset : 0x508 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PIN0 : Pin 0
bits : 0 - -1 (0 bit)
Enumeration: ( write )
1 : Set
Write: writing a '1' sets the pin high; writing a '0' has no effect
End of enumeration elements list.
PIN1 : Pin 1
bits : 1 - 0 (0 bit)
Enumeration: ( write )
1 : Set
Write: writing a '1' sets the pin high; writing a '0' has no effect
End of enumeration elements list.
PIN2 : Pin 2
bits : 2 - 1 (0 bit)
Enumeration: ( write )
1 : Set
Write: writing a '1' sets the pin high; writing a '0' has no effect
End of enumeration elements list.
PIN3 : Pin 3
bits : 3 - 2 (0 bit)
Enumeration: ( write )
1 : Set
Write: writing a '1' sets the pin high; writing a '0' has no effect
End of enumeration elements list.
PIN4 : Pin 4
bits : 4 - 3 (0 bit)
Enumeration: ( write )
1 : Set
Write: writing a '1' sets the pin high; writing a '0' has no effect
End of enumeration elements list.
PIN5 : Pin 5
bits : 5 - 4 (0 bit)
Enumeration: ( write )
1 : Set
Write: writing a '1' sets the pin high; writing a '0' has no effect
End of enumeration elements list.
PIN6 : Pin 6
bits : 6 - 5 (0 bit)
Enumeration: ( write )
1 : Set
Write: writing a '1' sets the pin high; writing a '0' has no effect
End of enumeration elements list.
PIN7 : Pin 7
bits : 7 - 6 (0 bit)
Enumeration: ( write )
1 : Set
Write: writing a '1' sets the pin high; writing a '0' has no effect
End of enumeration elements list.
PIN8 : Pin 8
bits : 8 - 7 (0 bit)
Enumeration: ( write )
1 : Set
Write: writing a '1' sets the pin high; writing a '0' has no effect
End of enumeration elements list.
PIN9 : Pin 9
bits : 9 - 8 (0 bit)
Enumeration: ( write )
1 : Set
Write: writing a '1' sets the pin high; writing a '0' has no effect
End of enumeration elements list.
PIN10 : Pin 10
bits : 10 - 9 (0 bit)
Enumeration: ( write )
1 : Set
Write: writing a '1' sets the pin high; writing a '0' has no effect
End of enumeration elements list.
PIN11 : Pin 11
bits : 11 - 10 (0 bit)
Enumeration: ( write )
1 : Set
Write: writing a '1' sets the pin high; writing a '0' has no effect
End of enumeration elements list.
PIN12 : Pin 12
bits : 12 - 11 (0 bit)
Enumeration: ( write )
1 : Set
Write: writing a '1' sets the pin high; writing a '0' has no effect
End of enumeration elements list.
PIN13 : Pin 13
bits : 13 - 12 (0 bit)
Enumeration: ( write )
1 : Set
Write: writing a '1' sets the pin high; writing a '0' has no effect
End of enumeration elements list.
PIN14 : Pin 14
bits : 14 - 13 (0 bit)
Enumeration: ( write )
1 : Set
Write: writing a '1' sets the pin high; writing a '0' has no effect
End of enumeration elements list.
PIN15 : Pin 15
bits : 15 - 14 (0 bit)
Enumeration: ( write )
1 : Set
Write: writing a '1' sets the pin high; writing a '0' has no effect
End of enumeration elements list.
PIN16 : Pin 16
bits : 16 - 15 (0 bit)
Enumeration: ( write )
1 : Set
Write: writing a '1' sets the pin high; writing a '0' has no effect
End of enumeration elements list.
PIN17 : Pin 17
bits : 17 - 16 (0 bit)
Enumeration: ( write )
1 : Set
Write: writing a '1' sets the pin high; writing a '0' has no effect
End of enumeration elements list.
PIN18 : Pin 18
bits : 18 - 17 (0 bit)
Enumeration: ( write )
1 : Set
Write: writing a '1' sets the pin high; writing a '0' has no effect
End of enumeration elements list.
PIN19 : Pin 19
bits : 19 - 18 (0 bit)
Enumeration: ( write )
1 : Set
Write: writing a '1' sets the pin high; writing a '0' has no effect
End of enumeration elements list.
PIN20 : Pin 20
bits : 20 - 19 (0 bit)
Enumeration: ( write )
1 : Set
Write: writing a '1' sets the pin high; writing a '0' has no effect
End of enumeration elements list.
PIN21 : Pin 21
bits : 21 - 20 (0 bit)
Enumeration: ( write )
1 : Set
Write: writing a '1' sets the pin high; writing a '0' has no effect
End of enumeration elements list.
PIN22 : Pin 22
bits : 22 - 21 (0 bit)
Enumeration: ( write )
1 : Set
Write: writing a '1' sets the pin high; writing a '0' has no effect
End of enumeration elements list.
PIN23 : Pin 23
bits : 23 - 22 (0 bit)
Enumeration: ( write )
1 : Set
Write: writing a '1' sets the pin high; writing a '0' has no effect
End of enumeration elements list.
PIN24 : Pin 24
bits : 24 - 23 (0 bit)
Enumeration: ( write )
1 : Set
Write: writing a '1' sets the pin high; writing a '0' has no effect
End of enumeration elements list.
PIN25 : Pin 25
bits : 25 - 24 (0 bit)
Enumeration: ( write )
1 : Set
Write: writing a '1' sets the pin high; writing a '0' has no effect
End of enumeration elements list.
PIN26 : Pin 26
bits : 26 - 25 (0 bit)
Enumeration: ( write )
1 : Set
Write: writing a '1' sets the pin high; writing a '0' has no effect
End of enumeration elements list.
PIN27 : Pin 27
bits : 27 - 26 (0 bit)
Enumeration: ( write )
1 : Set
Write: writing a '1' sets the pin high; writing a '0' has no effect
End of enumeration elements list.
PIN28 : Pin 28
bits : 28 - 27 (0 bit)
Enumeration: ( write )
1 : Set
Write: writing a '1' sets the pin high; writing a '0' has no effect
End of enumeration elements list.
PIN29 : Pin 29
bits : 29 - 28 (0 bit)
Enumeration: ( write )
1 : Set
Write: writing a '1' sets the pin high; writing a '0' has no effect
End of enumeration elements list.
PIN30 : Pin 30
bits : 30 - 29 (0 bit)
Enumeration: ( write )
1 : Set
Write: writing a '1' sets the pin high; writing a '0' has no effect
End of enumeration elements list.
PIN31 : Pin 31
bits : 31 - 30 (0 bit)
Enumeration: ( write )
1 : Set
Write: writing a '1' sets the pin high; writing a '0' has no effect
End of enumeration elements list.
Clear individual bits in GPIO port
address_offset : 0x50C Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PIN0 : Pin 0
bits : 0 - -1 (0 bit)
Enumeration: ( write )
1 : Clear
Write: writing a '1' sets the pin low; writing a '0' has no effect
End of enumeration elements list.
PIN1 : Pin 1
bits : 1 - 0 (0 bit)
Enumeration: ( write )
1 : Clear
Write: writing a '1' sets the pin low; writing a '0' has no effect
End of enumeration elements list.
PIN2 : Pin 2
bits : 2 - 1 (0 bit)
Enumeration: ( write )
1 : Clear
Write: writing a '1' sets the pin low; writing a '0' has no effect
End of enumeration elements list.
PIN3 : Pin 3
bits : 3 - 2 (0 bit)
Enumeration: ( write )
1 : Clear
Write: writing a '1' sets the pin low; writing a '0' has no effect
End of enumeration elements list.
PIN4 : Pin 4
bits : 4 - 3 (0 bit)
Enumeration: ( write )
1 : Clear
Write: writing a '1' sets the pin low; writing a '0' has no effect
End of enumeration elements list.
PIN5 : Pin 5
bits : 5 - 4 (0 bit)
Enumeration: ( write )
1 : Clear
Write: writing a '1' sets the pin low; writing a '0' has no effect
End of enumeration elements list.
PIN6 : Pin 6
bits : 6 - 5 (0 bit)
Enumeration: ( write )
1 : Clear
Write: writing a '1' sets the pin low; writing a '0' has no effect
End of enumeration elements list.
PIN7 : Pin 7
bits : 7 - 6 (0 bit)
Enumeration: ( write )
1 : Clear
Write: writing a '1' sets the pin low; writing a '0' has no effect
End of enumeration elements list.
PIN8 : Pin 8
bits : 8 - 7 (0 bit)
Enumeration: ( write )
1 : Clear
Write: writing a '1' sets the pin low; writing a '0' has no effect
End of enumeration elements list.
PIN9 : Pin 9
bits : 9 - 8 (0 bit)
Enumeration: ( write )
1 : Clear
Write: writing a '1' sets the pin low; writing a '0' has no effect
End of enumeration elements list.
PIN10 : Pin 10
bits : 10 - 9 (0 bit)
Enumeration: ( write )
1 : Clear
Write: writing a '1' sets the pin low; writing a '0' has no effect
End of enumeration elements list.
PIN11 : Pin 11
bits : 11 - 10 (0 bit)
Enumeration: ( write )
1 : Clear
Write: writing a '1' sets the pin low; writing a '0' has no effect
End of enumeration elements list.
PIN12 : Pin 12
bits : 12 - 11 (0 bit)
Enumeration: ( write )
1 : Clear
Write: writing a '1' sets the pin low; writing a '0' has no effect
End of enumeration elements list.
PIN13 : Pin 13
bits : 13 - 12 (0 bit)
Enumeration: ( write )
1 : Clear
Write: writing a '1' sets the pin low; writing a '0' has no effect
End of enumeration elements list.
PIN14 : Pin 14
bits : 14 - 13 (0 bit)
Enumeration: ( write )
1 : Clear
Write: writing a '1' sets the pin low; writing a '0' has no effect
End of enumeration elements list.
PIN15 : Pin 15
bits : 15 - 14 (0 bit)
Enumeration: ( write )
1 : Clear
Write: writing a '1' sets the pin low; writing a '0' has no effect
End of enumeration elements list.
PIN16 : Pin 16
bits : 16 - 15 (0 bit)
Enumeration: ( write )
1 : Clear
Write: writing a '1' sets the pin low; writing a '0' has no effect
End of enumeration elements list.
PIN17 : Pin 17
bits : 17 - 16 (0 bit)
Enumeration: ( write )
1 : Clear
Write: writing a '1' sets the pin low; writing a '0' has no effect
End of enumeration elements list.
PIN18 : Pin 18
bits : 18 - 17 (0 bit)
Enumeration: ( write )
1 : Clear
Write: writing a '1' sets the pin low; writing a '0' has no effect
End of enumeration elements list.
PIN19 : Pin 19
bits : 19 - 18 (0 bit)
Enumeration: ( write )
1 : Clear
Write: writing a '1' sets the pin low; writing a '0' has no effect
End of enumeration elements list.
PIN20 : Pin 20
bits : 20 - 19 (0 bit)
Enumeration: ( write )
1 : Clear
Write: writing a '1' sets the pin low; writing a '0' has no effect
End of enumeration elements list.
PIN21 : Pin 21
bits : 21 - 20 (0 bit)
Enumeration: ( write )
1 : Clear
Write: writing a '1' sets the pin low; writing a '0' has no effect
End of enumeration elements list.
PIN22 : Pin 22
bits : 22 - 21 (0 bit)
Enumeration: ( write )
1 : Clear
Write: writing a '1' sets the pin low; writing a '0' has no effect
End of enumeration elements list.
PIN23 : Pin 23
bits : 23 - 22 (0 bit)
Enumeration: ( write )
1 : Clear
Write: writing a '1' sets the pin low; writing a '0' has no effect
End of enumeration elements list.
PIN24 : Pin 24
bits : 24 - 23 (0 bit)
Enumeration: ( write )
1 : Clear
Write: writing a '1' sets the pin low; writing a '0' has no effect
End of enumeration elements list.
PIN25 : Pin 25
bits : 25 - 24 (0 bit)
Enumeration: ( write )
1 : Clear
Write: writing a '1' sets the pin low; writing a '0' has no effect
End of enumeration elements list.
PIN26 : Pin 26
bits : 26 - 25 (0 bit)
Enumeration: ( write )
1 : Clear
Write: writing a '1' sets the pin low; writing a '0' has no effect
End of enumeration elements list.
PIN27 : Pin 27
bits : 27 - 26 (0 bit)
Enumeration: ( write )
1 : Clear
Write: writing a '1' sets the pin low; writing a '0' has no effect
End of enumeration elements list.
PIN28 : Pin 28
bits : 28 - 27 (0 bit)
Enumeration: ( write )
1 : Clear
Write: writing a '1' sets the pin low; writing a '0' has no effect
End of enumeration elements list.
PIN29 : Pin 29
bits : 29 - 28 (0 bit)
Enumeration: ( write )
1 : Clear
Write: writing a '1' sets the pin low; writing a '0' has no effect
End of enumeration elements list.
PIN30 : Pin 30
bits : 30 - 29 (0 bit)
Enumeration: ( write )
1 : Clear
Write: writing a '1' sets the pin low; writing a '0' has no effect
End of enumeration elements list.
PIN31 : Pin 31
bits : 31 - 30 (0 bit)
Enumeration: ( write )
1 : Clear
Write: writing a '1' sets the pin low; writing a '0' has no effect
End of enumeration elements list.
Read GPIO port
address_offset : 0x510 Bytes (0x0)
access : read-only
reset_value : 0x0
reset_Mask : 0x0
PIN0 : Pin 0
bits : 0 - -1 (0 bit)
Enumeration:
0 : Low
Pin input is low
1 : High
Pin input is high
End of enumeration elements list.
PIN1 : Pin 1
bits : 1 - 0 (0 bit)
Enumeration:
0 : Low
Pin input is low
1 : High
Pin input is high
End of enumeration elements list.
PIN2 : Pin 2
bits : 2 - 1 (0 bit)
Enumeration:
0 : Low
Pin input is low
1 : High
Pin input is high
End of enumeration elements list.
PIN3 : Pin 3
bits : 3 - 2 (0 bit)
Enumeration:
0 : Low
Pin input is low
1 : High
Pin input is high
End of enumeration elements list.
PIN4 : Pin 4
bits : 4 - 3 (0 bit)
Enumeration:
0 : Low
Pin input is low
1 : High
Pin input is high
End of enumeration elements list.
PIN5 : Pin 5
bits : 5 - 4 (0 bit)
Enumeration:
0 : Low
Pin input is low
1 : High
Pin input is high
End of enumeration elements list.
PIN6 : Pin 6
bits : 6 - 5 (0 bit)
Enumeration:
0 : Low
Pin input is low
1 : High
Pin input is high
End of enumeration elements list.
PIN7 : Pin 7
bits : 7 - 6 (0 bit)
Enumeration:
0 : Low
Pin input is low
1 : High
Pin input is high
End of enumeration elements list.
PIN8 : Pin 8
bits : 8 - 7 (0 bit)
Enumeration:
0 : Low
Pin input is low
1 : High
Pin input is high
End of enumeration elements list.
PIN9 : Pin 9
bits : 9 - 8 (0 bit)
Enumeration:
0 : Low
Pin input is low
1 : High
Pin input is high
End of enumeration elements list.
PIN10 : Pin 10
bits : 10 - 9 (0 bit)
Enumeration:
0 : Low
Pin input is low
1 : High
Pin input is high
End of enumeration elements list.
PIN11 : Pin 11
bits : 11 - 10 (0 bit)
Enumeration:
0 : Low
Pin input is low
1 : High
Pin input is high
End of enumeration elements list.
PIN12 : Pin 12
bits : 12 - 11 (0 bit)
Enumeration:
0 : Low
Pin input is low
1 : High
Pin input is high
End of enumeration elements list.
PIN13 : Pin 13
bits : 13 - 12 (0 bit)
Enumeration:
0 : Low
Pin input is low
1 : High
Pin input is high
End of enumeration elements list.
PIN14 : Pin 14
bits : 14 - 13 (0 bit)
Enumeration:
0 : Low
Pin input is low
1 : High
Pin input is high
End of enumeration elements list.
PIN15 : Pin 15
bits : 15 - 14 (0 bit)
Enumeration:
0 : Low
Pin input is low
1 : High
Pin input is high
End of enumeration elements list.
PIN16 : Pin 16
bits : 16 - 15 (0 bit)
Enumeration:
0 : Low
Pin input is low
1 : High
Pin input is high
End of enumeration elements list.
PIN17 : Pin 17
bits : 17 - 16 (0 bit)
Enumeration:
0 : Low
Pin input is low
1 : High
Pin input is high
End of enumeration elements list.
PIN18 : Pin 18
bits : 18 - 17 (0 bit)
Enumeration:
0 : Low
Pin input is low
1 : High
Pin input is high
End of enumeration elements list.
PIN19 : Pin 19
bits : 19 - 18 (0 bit)
Enumeration:
0 : Low
Pin input is low
1 : High
Pin input is high
End of enumeration elements list.
PIN20 : Pin 20
bits : 20 - 19 (0 bit)
Enumeration:
0 : Low
Pin input is low
1 : High
Pin input is high
End of enumeration elements list.
PIN21 : Pin 21
bits : 21 - 20 (0 bit)
Enumeration:
0 : Low
Pin input is low
1 : High
Pin input is high
End of enumeration elements list.
PIN22 : Pin 22
bits : 22 - 21 (0 bit)
Enumeration:
0 : Low
Pin input is low
1 : High
Pin input is high
End of enumeration elements list.
PIN23 : Pin 23
bits : 23 - 22 (0 bit)
Enumeration:
0 : Low
Pin input is low
1 : High
Pin input is high
End of enumeration elements list.
PIN24 : Pin 24
bits : 24 - 23 (0 bit)
Enumeration:
0 : Low
Pin input is low
1 : High
Pin input is high
End of enumeration elements list.
PIN25 : Pin 25
bits : 25 - 24 (0 bit)
Enumeration:
0 : Low
Pin input is low
1 : High
Pin input is high
End of enumeration elements list.
PIN26 : Pin 26
bits : 26 - 25 (0 bit)
Enumeration:
0 : Low
Pin input is low
1 : High
Pin input is high
End of enumeration elements list.
PIN27 : Pin 27
bits : 27 - 26 (0 bit)
Enumeration:
0 : Low
Pin input is low
1 : High
Pin input is high
End of enumeration elements list.
PIN28 : Pin 28
bits : 28 - 27 (0 bit)
Enumeration:
0 : Low
Pin input is low
1 : High
Pin input is high
End of enumeration elements list.
PIN29 : Pin 29
bits : 29 - 28 (0 bit)
Enumeration:
0 : Low
Pin input is low
1 : High
Pin input is high
End of enumeration elements list.
PIN30 : Pin 30
bits : 30 - 29 (0 bit)
Enumeration:
0 : Low
Pin input is low
1 : High
Pin input is high
End of enumeration elements list.
PIN31 : Pin 31
bits : 31 - 30 (0 bit)
Enumeration:
0 : Low
Pin input is low
1 : High
Pin input is high
End of enumeration elements list.
Direction of GPIO pins
address_offset : 0x514 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PIN0 : Pin 0
bits : 0 - -1 (0 bit)
Enumeration:
0 : Input
Pin set as input
1 : Output
Pin set as output
End of enumeration elements list.
PIN1 : Pin 1
bits : 1 - 0 (0 bit)
Enumeration:
0 : Input
Pin set as input
1 : Output
Pin set as output
End of enumeration elements list.
PIN2 : Pin 2
bits : 2 - 1 (0 bit)
Enumeration:
0 : Input
Pin set as input
1 : Output
Pin set as output
End of enumeration elements list.
PIN3 : Pin 3
bits : 3 - 2 (0 bit)
Enumeration:
0 : Input
Pin set as input
1 : Output
Pin set as output
End of enumeration elements list.
PIN4 : Pin 4
bits : 4 - 3 (0 bit)
Enumeration:
0 : Input
Pin set as input
1 : Output
Pin set as output
End of enumeration elements list.
PIN5 : Pin 5
bits : 5 - 4 (0 bit)
Enumeration:
0 : Input
Pin set as input
1 : Output
Pin set as output
End of enumeration elements list.
PIN6 : Pin 6
bits : 6 - 5 (0 bit)
Enumeration:
0 : Input
Pin set as input
1 : Output
Pin set as output
End of enumeration elements list.
PIN7 : Pin 7
bits : 7 - 6 (0 bit)
Enumeration:
0 : Input
Pin set as input
1 : Output
Pin set as output
End of enumeration elements list.
PIN8 : Pin 8
bits : 8 - 7 (0 bit)
Enumeration:
0 : Input
Pin set as input
1 : Output
Pin set as output
End of enumeration elements list.
PIN9 : Pin 9
bits : 9 - 8 (0 bit)
Enumeration:
0 : Input
Pin set as input
1 : Output
Pin set as output
End of enumeration elements list.
PIN10 : Pin 10
bits : 10 - 9 (0 bit)
Enumeration:
0 : Input
Pin set as input
1 : Output
Pin set as output
End of enumeration elements list.
PIN11 : Pin 11
bits : 11 - 10 (0 bit)
Enumeration:
0 : Input
Pin set as input
1 : Output
Pin set as output
End of enumeration elements list.
PIN12 : Pin 12
bits : 12 - 11 (0 bit)
Enumeration:
0 : Input
Pin set as input
1 : Output
Pin set as output
End of enumeration elements list.
PIN13 : Pin 13
bits : 13 - 12 (0 bit)
Enumeration:
0 : Input
Pin set as input
1 : Output
Pin set as output
End of enumeration elements list.
PIN14 : Pin 14
bits : 14 - 13 (0 bit)
Enumeration:
0 : Input
Pin set as input
1 : Output
Pin set as output
End of enumeration elements list.
PIN15 : Pin 15
bits : 15 - 14 (0 bit)
Enumeration:
0 : Input
Pin set as input
1 : Output
Pin set as output
End of enumeration elements list.
PIN16 : Pin 16
bits : 16 - 15 (0 bit)
Enumeration:
0 : Input
Pin set as input
1 : Output
Pin set as output
End of enumeration elements list.
PIN17 : Pin 17
bits : 17 - 16 (0 bit)
Enumeration:
0 : Input
Pin set as input
1 : Output
Pin set as output
End of enumeration elements list.
PIN18 : Pin 18
bits : 18 - 17 (0 bit)
Enumeration:
0 : Input
Pin set as input
1 : Output
Pin set as output
End of enumeration elements list.
PIN19 : Pin 19
bits : 19 - 18 (0 bit)
Enumeration:
0 : Input
Pin set as input
1 : Output
Pin set as output
End of enumeration elements list.
PIN20 : Pin 20
bits : 20 - 19 (0 bit)
Enumeration:
0 : Input
Pin set as input
1 : Output
Pin set as output
End of enumeration elements list.
PIN21 : Pin 21
bits : 21 - 20 (0 bit)
Enumeration:
0 : Input
Pin set as input
1 : Output
Pin set as output
End of enumeration elements list.
PIN22 : Pin 22
bits : 22 - 21 (0 bit)
Enumeration:
0 : Input
Pin set as input
1 : Output
Pin set as output
End of enumeration elements list.
PIN23 : Pin 23
bits : 23 - 22 (0 bit)
Enumeration:
0 : Input
Pin set as input
1 : Output
Pin set as output
End of enumeration elements list.
PIN24 : Pin 24
bits : 24 - 23 (0 bit)
Enumeration:
0 : Input
Pin set as input
1 : Output
Pin set as output
End of enumeration elements list.
PIN25 : Pin 25
bits : 25 - 24 (0 bit)
Enumeration:
0 : Input
Pin set as input
1 : Output
Pin set as output
End of enumeration elements list.
PIN26 : Pin 26
bits : 26 - 25 (0 bit)
Enumeration:
0 : Input
Pin set as input
1 : Output
Pin set as output
End of enumeration elements list.
PIN27 : Pin 27
bits : 27 - 26 (0 bit)
Enumeration:
0 : Input
Pin set as input
1 : Output
Pin set as output
End of enumeration elements list.
PIN28 : Pin 28
bits : 28 - 27 (0 bit)
Enumeration:
0 : Input
Pin set as input
1 : Output
Pin set as output
End of enumeration elements list.
PIN29 : Pin 29
bits : 29 - 28 (0 bit)
Enumeration:
0 : Input
Pin set as input
1 : Output
Pin set as output
End of enumeration elements list.
PIN30 : Pin 30
bits : 30 - 29 (0 bit)
Enumeration:
0 : Input
Pin set as input
1 : Output
Pin set as output
End of enumeration elements list.
PIN31 : Pin 31
bits : 31 - 30 (0 bit)
Enumeration:
0 : Input
Pin set as input
1 : Output
Pin set as output
End of enumeration elements list.
DIR set register
address_offset : 0x518 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PIN0 : Set as output pin 0
bits : 0 - -1 (0 bit)
Enumeration: ( write )
1 : Set
Write: writing a '1' sets pin to output; writing a '0' has no effect
End of enumeration elements list.
PIN1 : Set as output pin 1
bits : 1 - 0 (0 bit)
Enumeration: ( write )
1 : Set
Write: writing a '1' sets pin to output; writing a '0' has no effect
End of enumeration elements list.
PIN2 : Set as output pin 2
bits : 2 - 1 (0 bit)
Enumeration: ( write )
1 : Set
Write: writing a '1' sets pin to output; writing a '0' has no effect
End of enumeration elements list.
PIN3 : Set as output pin 3
bits : 3 - 2 (0 bit)
Enumeration: ( write )
1 : Set
Write: writing a '1' sets pin to output; writing a '0' has no effect
End of enumeration elements list.
PIN4 : Set as output pin 4
bits : 4 - 3 (0 bit)
Enumeration: ( write )
1 : Set
Write: writing a '1' sets pin to output; writing a '0' has no effect
End of enumeration elements list.
PIN5 : Set as output pin 5
bits : 5 - 4 (0 bit)
Enumeration: ( write )
1 : Set
Write: writing a '1' sets pin to output; writing a '0' has no effect
End of enumeration elements list.
PIN6 : Set as output pin 6
bits : 6 - 5 (0 bit)
Enumeration: ( write )
1 : Set
Write: writing a '1' sets pin to output; writing a '0' has no effect
End of enumeration elements list.
PIN7 : Set as output pin 7
bits : 7 - 6 (0 bit)
Enumeration: ( write )
1 : Set
Write: writing a '1' sets pin to output; writing a '0' has no effect
End of enumeration elements list.
PIN8 : Set as output pin 8
bits : 8 - 7 (0 bit)
Enumeration: ( write )
1 : Set
Write: writing a '1' sets pin to output; writing a '0' has no effect
End of enumeration elements list.
PIN9 : Set as output pin 9
bits : 9 - 8 (0 bit)
Enumeration: ( write )
1 : Set
Write: writing a '1' sets pin to output; writing a '0' has no effect
End of enumeration elements list.
PIN10 : Set as output pin 10
bits : 10 - 9 (0 bit)
Enumeration: ( write )
1 : Set
Write: writing a '1' sets pin to output; writing a '0' has no effect
End of enumeration elements list.
PIN11 : Set as output pin 11
bits : 11 - 10 (0 bit)
Enumeration: ( write )
1 : Set
Write: writing a '1' sets pin to output; writing a '0' has no effect
End of enumeration elements list.
PIN12 : Set as output pin 12
bits : 12 - 11 (0 bit)
Enumeration: ( write )
1 : Set
Write: writing a '1' sets pin to output; writing a '0' has no effect
End of enumeration elements list.
PIN13 : Set as output pin 13
bits : 13 - 12 (0 bit)
Enumeration: ( write )
1 : Set
Write: writing a '1' sets pin to output; writing a '0' has no effect
End of enumeration elements list.
PIN14 : Set as output pin 14
bits : 14 - 13 (0 bit)
Enumeration: ( write )
1 : Set
Write: writing a '1' sets pin to output; writing a '0' has no effect
End of enumeration elements list.
PIN15 : Set as output pin 15
bits : 15 - 14 (0 bit)
Enumeration: ( write )
1 : Set
Write: writing a '1' sets pin to output; writing a '0' has no effect
End of enumeration elements list.
PIN16 : Set as output pin 16
bits : 16 - 15 (0 bit)
Enumeration: ( write )
1 : Set
Write: writing a '1' sets pin to output; writing a '0' has no effect
End of enumeration elements list.
PIN17 : Set as output pin 17
bits : 17 - 16 (0 bit)
Enumeration: ( write )
1 : Set
Write: writing a '1' sets pin to output; writing a '0' has no effect
End of enumeration elements list.
PIN18 : Set as output pin 18
bits : 18 - 17 (0 bit)
Enumeration: ( write )
1 : Set
Write: writing a '1' sets pin to output; writing a '0' has no effect
End of enumeration elements list.
PIN19 : Set as output pin 19
bits : 19 - 18 (0 bit)
Enumeration: ( write )
1 : Set
Write: writing a '1' sets pin to output; writing a '0' has no effect
End of enumeration elements list.
PIN20 : Set as output pin 20
bits : 20 - 19 (0 bit)
Enumeration: ( write )
1 : Set
Write: writing a '1' sets pin to output; writing a '0' has no effect
End of enumeration elements list.
PIN21 : Set as output pin 21
bits : 21 - 20 (0 bit)
Enumeration: ( write )
1 : Set
Write: writing a '1' sets pin to output; writing a '0' has no effect
End of enumeration elements list.
PIN22 : Set as output pin 22
bits : 22 - 21 (0 bit)
Enumeration: ( write )
1 : Set
Write: writing a '1' sets pin to output; writing a '0' has no effect
End of enumeration elements list.
PIN23 : Set as output pin 23
bits : 23 - 22 (0 bit)
Enumeration: ( write )
1 : Set
Write: writing a '1' sets pin to output; writing a '0' has no effect
End of enumeration elements list.
PIN24 : Set as output pin 24
bits : 24 - 23 (0 bit)
Enumeration: ( write )
1 : Set
Write: writing a '1' sets pin to output; writing a '0' has no effect
End of enumeration elements list.
PIN25 : Set as output pin 25
bits : 25 - 24 (0 bit)
Enumeration: ( write )
1 : Set
Write: writing a '1' sets pin to output; writing a '0' has no effect
End of enumeration elements list.
PIN26 : Set as output pin 26
bits : 26 - 25 (0 bit)
Enumeration: ( write )
1 : Set
Write: writing a '1' sets pin to output; writing a '0' has no effect
End of enumeration elements list.
PIN27 : Set as output pin 27
bits : 27 - 26 (0 bit)
Enumeration: ( write )
1 : Set
Write: writing a '1' sets pin to output; writing a '0' has no effect
End of enumeration elements list.
PIN28 : Set as output pin 28
bits : 28 - 27 (0 bit)
Enumeration: ( write )
1 : Set
Write: writing a '1' sets pin to output; writing a '0' has no effect
End of enumeration elements list.
PIN29 : Set as output pin 29
bits : 29 - 28 (0 bit)
Enumeration: ( write )
1 : Set
Write: writing a '1' sets pin to output; writing a '0' has no effect
End of enumeration elements list.
PIN30 : Set as output pin 30
bits : 30 - 29 (0 bit)
Enumeration: ( write )
1 : Set
Write: writing a '1' sets pin to output; writing a '0' has no effect
End of enumeration elements list.
PIN31 : Set as output pin 31
bits : 31 - 30 (0 bit)
Enumeration: ( write )
1 : Set
Write: writing a '1' sets pin to output; writing a '0' has no effect
End of enumeration elements list.
DIR clear register
address_offset : 0x51C Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PIN0 : Set as input pin 0
bits : 0 - -1 (0 bit)
Enumeration: ( write )
1 : Clear
Write: writing a '1' sets pin to input; writing a '0' has no effect
End of enumeration elements list.
PIN1 : Set as input pin 1
bits : 1 - 0 (0 bit)
Enumeration: ( write )
1 : Clear
Write: writing a '1' sets pin to input; writing a '0' has no effect
End of enumeration elements list.
PIN2 : Set as input pin 2
bits : 2 - 1 (0 bit)
Enumeration: ( write )
1 : Clear
Write: writing a '1' sets pin to input; writing a '0' has no effect
End of enumeration elements list.
PIN3 : Set as input pin 3
bits : 3 - 2 (0 bit)
Enumeration: ( write )
1 : Clear
Write: writing a '1' sets pin to input; writing a '0' has no effect
End of enumeration elements list.
PIN4 : Set as input pin 4
bits : 4 - 3 (0 bit)
Enumeration: ( write )
1 : Clear
Write: writing a '1' sets pin to input; writing a '0' has no effect
End of enumeration elements list.
PIN5 : Set as input pin 5
bits : 5 - 4 (0 bit)
Enumeration: ( write )
1 : Clear
Write: writing a '1' sets pin to input; writing a '0' has no effect
End of enumeration elements list.
PIN6 : Set as input pin 6
bits : 6 - 5 (0 bit)
Enumeration: ( write )
1 : Clear
Write: writing a '1' sets pin to input; writing a '0' has no effect
End of enumeration elements list.
PIN7 : Set as input pin 7
bits : 7 - 6 (0 bit)
Enumeration: ( write )
1 : Clear
Write: writing a '1' sets pin to input; writing a '0' has no effect
End of enumeration elements list.
PIN8 : Set as input pin 8
bits : 8 - 7 (0 bit)
Enumeration: ( write )
1 : Clear
Write: writing a '1' sets pin to input; writing a '0' has no effect
End of enumeration elements list.
PIN9 : Set as input pin 9
bits : 9 - 8 (0 bit)
Enumeration: ( write )
1 : Clear
Write: writing a '1' sets pin to input; writing a '0' has no effect
End of enumeration elements list.
PIN10 : Set as input pin 10
bits : 10 - 9 (0 bit)
Enumeration: ( write )
1 : Clear
Write: writing a '1' sets pin to input; writing a '0' has no effect
End of enumeration elements list.
PIN11 : Set as input pin 11
bits : 11 - 10 (0 bit)
Enumeration: ( write )
1 : Clear
Write: writing a '1' sets pin to input; writing a '0' has no effect
End of enumeration elements list.
PIN12 : Set as input pin 12
bits : 12 - 11 (0 bit)
Enumeration: ( write )
1 : Clear
Write: writing a '1' sets pin to input; writing a '0' has no effect
End of enumeration elements list.
PIN13 : Set as input pin 13
bits : 13 - 12 (0 bit)
Enumeration: ( write )
1 : Clear
Write: writing a '1' sets pin to input; writing a '0' has no effect
End of enumeration elements list.
PIN14 : Set as input pin 14
bits : 14 - 13 (0 bit)
Enumeration: ( write )
1 : Clear
Write: writing a '1' sets pin to input; writing a '0' has no effect
End of enumeration elements list.
PIN15 : Set as input pin 15
bits : 15 - 14 (0 bit)
Enumeration: ( write )
1 : Clear
Write: writing a '1' sets pin to input; writing a '0' has no effect
End of enumeration elements list.
PIN16 : Set as input pin 16
bits : 16 - 15 (0 bit)
Enumeration: ( write )
1 : Clear
Write: writing a '1' sets pin to input; writing a '0' has no effect
End of enumeration elements list.
PIN17 : Set as input pin 17
bits : 17 - 16 (0 bit)
Enumeration: ( write )
1 : Clear
Write: writing a '1' sets pin to input; writing a '0' has no effect
End of enumeration elements list.
PIN18 : Set as input pin 18
bits : 18 - 17 (0 bit)
Enumeration: ( write )
1 : Clear
Write: writing a '1' sets pin to input; writing a '0' has no effect
End of enumeration elements list.
PIN19 : Set as input pin 19
bits : 19 - 18 (0 bit)
Enumeration: ( write )
1 : Clear
Write: writing a '1' sets pin to input; writing a '0' has no effect
End of enumeration elements list.
PIN20 : Set as input pin 20
bits : 20 - 19 (0 bit)
Enumeration: ( write )
1 : Clear
Write: writing a '1' sets pin to input; writing a '0' has no effect
End of enumeration elements list.
PIN21 : Set as input pin 21
bits : 21 - 20 (0 bit)
Enumeration: ( write )
1 : Clear
Write: writing a '1' sets pin to input; writing a '0' has no effect
End of enumeration elements list.
PIN22 : Set as input pin 22
bits : 22 - 21 (0 bit)
Enumeration: ( write )
1 : Clear
Write: writing a '1' sets pin to input; writing a '0' has no effect
End of enumeration elements list.
PIN23 : Set as input pin 23
bits : 23 - 22 (0 bit)
Enumeration: ( write )
1 : Clear
Write: writing a '1' sets pin to input; writing a '0' has no effect
End of enumeration elements list.
PIN24 : Set as input pin 24
bits : 24 - 23 (0 bit)
Enumeration: ( write )
1 : Clear
Write: writing a '1' sets pin to input; writing a '0' has no effect
End of enumeration elements list.
PIN25 : Set as input pin 25
bits : 25 - 24 (0 bit)
Enumeration: ( write )
1 : Clear
Write: writing a '1' sets pin to input; writing a '0' has no effect
End of enumeration elements list.
PIN26 : Set as input pin 26
bits : 26 - 25 (0 bit)
Enumeration: ( write )
1 : Clear
Write: writing a '1' sets pin to input; writing a '0' has no effect
End of enumeration elements list.
PIN27 : Set as input pin 27
bits : 27 - 26 (0 bit)
Enumeration: ( write )
1 : Clear
Write: writing a '1' sets pin to input; writing a '0' has no effect
End of enumeration elements list.
PIN28 : Set as input pin 28
bits : 28 - 27 (0 bit)
Enumeration: ( write )
1 : Clear
Write: writing a '1' sets pin to input; writing a '0' has no effect
End of enumeration elements list.
PIN29 : Set as input pin 29
bits : 29 - 28 (0 bit)
Enumeration: ( write )
1 : Clear
Write: writing a '1' sets pin to input; writing a '0' has no effect
End of enumeration elements list.
PIN30 : Set as input pin 30
bits : 30 - 29 (0 bit)
Enumeration: ( write )
1 : Clear
Write: writing a '1' sets pin to input; writing a '0' has no effect
End of enumeration elements list.
PIN31 : Set as input pin 31
bits : 31 - 30 (0 bit)
Enumeration: ( write )
1 : Clear
Write: writing a '1' sets pin to input; writing a '0' has no effect
End of enumeration elements list.
Latch register indicating what GPIO pins that have met the criteria set in the PIN_CNF[n].SENSE registers
address_offset : 0x520 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PIN0 : Status on whether PIN0 has met criteria set in PIN_CNF0.SENSE register. Write '1' to clear.
bits : 0 - -1 (0 bit)
Enumeration:
0 : NotLatched
Criteria has not been met
1 : Latched
Criteria has been met
End of enumeration elements list.
PIN1 : Status on whether PIN1 has met criteria set in PIN_CNF1.SENSE register. Write '1' to clear.
bits : 1 - 0 (0 bit)
Enumeration:
0 : NotLatched
Criteria has not been met
1 : Latched
Criteria has been met
End of enumeration elements list.
PIN2 : Status on whether PIN2 has met criteria set in PIN_CNF2.SENSE register. Write '1' to clear.
bits : 2 - 1 (0 bit)
Enumeration:
0 : NotLatched
Criteria has not been met
1 : Latched
Criteria has been met
End of enumeration elements list.
PIN3 : Status on whether PIN3 has met criteria set in PIN_CNF3.SENSE register. Write '1' to clear.
bits : 3 - 2 (0 bit)
Enumeration:
0 : NotLatched
Criteria has not been met
1 : Latched
Criteria has been met
End of enumeration elements list.
PIN4 : Status on whether PIN4 has met criteria set in PIN_CNF4.SENSE register. Write '1' to clear.
bits : 4 - 3 (0 bit)
Enumeration:
0 : NotLatched
Criteria has not been met
1 : Latched
Criteria has been met
End of enumeration elements list.
PIN5 : Status on whether PIN5 has met criteria set in PIN_CNF5.SENSE register. Write '1' to clear.
bits : 5 - 4 (0 bit)
Enumeration:
0 : NotLatched
Criteria has not been met
1 : Latched
Criteria has been met
End of enumeration elements list.
PIN6 : Status on whether PIN6 has met criteria set in PIN_CNF6.SENSE register. Write '1' to clear.
bits : 6 - 5 (0 bit)
Enumeration:
0 : NotLatched
Criteria has not been met
1 : Latched
Criteria has been met
End of enumeration elements list.
PIN7 : Status on whether PIN7 has met criteria set in PIN_CNF7.SENSE register. Write '1' to clear.
bits : 7 - 6 (0 bit)
Enumeration:
0 : NotLatched
Criteria has not been met
1 : Latched
Criteria has been met
End of enumeration elements list.
PIN8 : Status on whether PIN8 has met criteria set in PIN_CNF8.SENSE register. Write '1' to clear.
bits : 8 - 7 (0 bit)
Enumeration:
0 : NotLatched
Criteria has not been met
1 : Latched
Criteria has been met
End of enumeration elements list.
PIN9 : Status on whether PIN9 has met criteria set in PIN_CNF9.SENSE register. Write '1' to clear.
bits : 9 - 8 (0 bit)
Enumeration:
0 : NotLatched
Criteria has not been met
1 : Latched
Criteria has been met
End of enumeration elements list.
PIN10 : Status on whether PIN10 has met criteria set in PIN_CNF10.SENSE register. Write '1' to clear.
bits : 10 - 9 (0 bit)
Enumeration:
0 : NotLatched
Criteria has not been met
1 : Latched
Criteria has been met
End of enumeration elements list.
PIN11 : Status on whether PIN11 has met criteria set in PIN_CNF11.SENSE register. Write '1' to clear.
bits : 11 - 10 (0 bit)
Enumeration:
0 : NotLatched
Criteria has not been met
1 : Latched
Criteria has been met
End of enumeration elements list.
PIN12 : Status on whether PIN12 has met criteria set in PIN_CNF12.SENSE register. Write '1' to clear.
bits : 12 - 11 (0 bit)
Enumeration:
0 : NotLatched
Criteria has not been met
1 : Latched
Criteria has been met
End of enumeration elements list.
PIN13 : Status on whether PIN13 has met criteria set in PIN_CNF13.SENSE register. Write '1' to clear.
bits : 13 - 12 (0 bit)
Enumeration:
0 : NotLatched
Criteria has not been met
1 : Latched
Criteria has been met
End of enumeration elements list.
PIN14 : Status on whether PIN14 has met criteria set in PIN_CNF14.SENSE register. Write '1' to clear.
bits : 14 - 13 (0 bit)
Enumeration:
0 : NotLatched
Criteria has not been met
1 : Latched
Criteria has been met
End of enumeration elements list.
PIN15 : Status on whether PIN15 has met criteria set in PIN_CNF15.SENSE register. Write '1' to clear.
bits : 15 - 14 (0 bit)
Enumeration:
0 : NotLatched
Criteria has not been met
1 : Latched
Criteria has been met
End of enumeration elements list.
PIN16 : Status on whether PIN16 has met criteria set in PIN_CNF16.SENSE register. Write '1' to clear.
bits : 16 - 15 (0 bit)
Enumeration:
0 : NotLatched
Criteria has not been met
1 : Latched
Criteria has been met
End of enumeration elements list.
PIN17 : Status on whether PIN17 has met criteria set in PIN_CNF17.SENSE register. Write '1' to clear.
bits : 17 - 16 (0 bit)
Enumeration:
0 : NotLatched
Criteria has not been met
1 : Latched
Criteria has been met
End of enumeration elements list.
PIN18 : Status on whether PIN18 has met criteria set in PIN_CNF18.SENSE register. Write '1' to clear.
bits : 18 - 17 (0 bit)
Enumeration:
0 : NotLatched
Criteria has not been met
1 : Latched
Criteria has been met
End of enumeration elements list.
PIN19 : Status on whether PIN19 has met criteria set in PIN_CNF19.SENSE register. Write '1' to clear.
bits : 19 - 18 (0 bit)
Enumeration:
0 : NotLatched
Criteria has not been met
1 : Latched
Criteria has been met
End of enumeration elements list.
PIN20 : Status on whether PIN20 has met criteria set in PIN_CNF20.SENSE register. Write '1' to clear.
bits : 20 - 19 (0 bit)
Enumeration:
0 : NotLatched
Criteria has not been met
1 : Latched
Criteria has been met
End of enumeration elements list.
PIN21 : Status on whether PIN21 has met criteria set in PIN_CNF21.SENSE register. Write '1' to clear.
bits : 21 - 20 (0 bit)
Enumeration:
0 : NotLatched
Criteria has not been met
1 : Latched
Criteria has been met
End of enumeration elements list.
PIN22 : Status on whether PIN22 has met criteria set in PIN_CNF22.SENSE register. Write '1' to clear.
bits : 22 - 21 (0 bit)
Enumeration:
0 : NotLatched
Criteria has not been met
1 : Latched
Criteria has been met
End of enumeration elements list.
PIN23 : Status on whether PIN23 has met criteria set in PIN_CNF23.SENSE register. Write '1' to clear.
bits : 23 - 22 (0 bit)
Enumeration:
0 : NotLatched
Criteria has not been met
1 : Latched
Criteria has been met
End of enumeration elements list.
PIN24 : Status on whether PIN24 has met criteria set in PIN_CNF24.SENSE register. Write '1' to clear.
bits : 24 - 23 (0 bit)
Enumeration:
0 : NotLatched
Criteria has not been met
1 : Latched
Criteria has been met
End of enumeration elements list.
PIN25 : Status on whether PIN25 has met criteria set in PIN_CNF25.SENSE register. Write '1' to clear.
bits : 25 - 24 (0 bit)
Enumeration:
0 : NotLatched
Criteria has not been met
1 : Latched
Criteria has been met
End of enumeration elements list.
PIN26 : Status on whether PIN26 has met criteria set in PIN_CNF26.SENSE register. Write '1' to clear.
bits : 26 - 25 (0 bit)
Enumeration:
0 : NotLatched
Criteria has not been met
1 : Latched
Criteria has been met
End of enumeration elements list.
PIN27 : Status on whether PIN27 has met criteria set in PIN_CNF27.SENSE register. Write '1' to clear.
bits : 27 - 26 (0 bit)
Enumeration:
0 : NotLatched
Criteria has not been met
1 : Latched
Criteria has been met
End of enumeration elements list.
PIN28 : Status on whether PIN28 has met criteria set in PIN_CNF28.SENSE register. Write '1' to clear.
bits : 28 - 27 (0 bit)
Enumeration:
0 : NotLatched
Criteria has not been met
1 : Latched
Criteria has been met
End of enumeration elements list.
PIN29 : Status on whether PIN29 has met criteria set in PIN_CNF29.SENSE register. Write '1' to clear.
bits : 29 - 28 (0 bit)
Enumeration:
0 : NotLatched
Criteria has not been met
1 : Latched
Criteria has been met
End of enumeration elements list.
PIN30 : Status on whether PIN30 has met criteria set in PIN_CNF30.SENSE register. Write '1' to clear.
bits : 30 - 29 (0 bit)
Enumeration:
0 : NotLatched
Criteria has not been met
1 : Latched
Criteria has been met
End of enumeration elements list.
PIN31 : Status on whether PIN31 has met criteria set in PIN_CNF31.SENSE register. Write '1' to clear.
bits : 31 - 30 (0 bit)
Enumeration:
0 : NotLatched
Criteria has not been met
1 : Latched
Criteria has been met
End of enumeration elements list.
Select between default DETECT signal behaviour and LDETECT mode
address_offset : 0x524 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DETECTMODE : Select between default DETECT signal behaviour and LDETECT mode
bits : 0 - -1 (0 bit)
Enumeration:
0 : Default
DETECT directly connected to PIN DETECT signals
1 : LDETECT
Use the latched LDETECT behaviour
End of enumeration elements list.
Description collection: Configuration of GPIO pins
address_offset : 0x54DC Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DIR : Pin direction. Same physical register as DIR register
bits : 0 - -1 (0 bit)
Enumeration:
0 : Input
Configure pin as an input pin
1 : Output
Configure pin as an output pin
End of enumeration elements list.
INPUT : Connect or disconnect input buffer
bits : 1 - 0 (0 bit)
Enumeration:
0 : Connect
Connect input buffer
1 : Disconnect
Disconnect input buffer
End of enumeration elements list.
PULL : Pull configuration
bits : 2 - 2 (1 bit)
Enumeration:
0 : Disabled
No pull
1 : Pulldown
Pull down on pin
3 : Pullup
Pull up on pin
End of enumeration elements list.
DRIVE : Drive configuration
bits : 8 - 9 (2 bit)
Enumeration:
0 : S0S1
Standard '0', standard '1'
1 : H0S1
High drive '0', standard '1'
2 : S0H1
Standard '0', high drive '1'
3 : H0H1
High drive '0', high 'drive '1''
4 : D0S1
Disconnect '0' standard '1' (normally used for wired-or connections)
5 : D0H1
Disconnect '0', high drive '1' (normally used for wired-or connections)
6 : S0D1
Standard '0'. disconnect '1' (normally used for wired-and connections)
7 : H0D1
High drive '0', disconnect '1' (normally used for wired-and connections)
End of enumeration elements list.
SENSE : Pin sensing mechanism
bits : 16 - 16 (1 bit)
Enumeration:
0 : Disabled
Disabled
2 : High
Sense for high level
3 : Low
Sense for low level
End of enumeration elements list.
Description collection: Configuration of GPIO pins
address_offset : 0x5C08 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DIR : Pin direction. Same physical register as DIR register
bits : 0 - -1 (0 bit)
Enumeration:
0 : Input
Configure pin as an input pin
1 : Output
Configure pin as an output pin
End of enumeration elements list.
INPUT : Connect or disconnect input buffer
bits : 1 - 0 (0 bit)
Enumeration:
0 : Connect
Connect input buffer
1 : Disconnect
Disconnect input buffer
End of enumeration elements list.
PULL : Pull configuration
bits : 2 - 2 (1 bit)
Enumeration:
0 : Disabled
No pull
1 : Pulldown
Pull down on pin
3 : Pullup
Pull up on pin
End of enumeration elements list.
DRIVE : Drive configuration
bits : 8 - 9 (2 bit)
Enumeration:
0 : S0S1
Standard '0', standard '1'
1 : H0S1
High drive '0', standard '1'
2 : S0H1
Standard '0', high drive '1'
3 : H0H1
High drive '0', high 'drive '1''
4 : D0S1
Disconnect '0' standard '1' (normally used for wired-or connections)
5 : D0H1
Disconnect '0', high drive '1' (normally used for wired-or connections)
6 : S0D1
Standard '0'. disconnect '1' (normally used for wired-and connections)
7 : H0D1
High drive '0', disconnect '1' (normally used for wired-and connections)
End of enumeration elements list.
SENSE : Pin sensing mechanism
bits : 16 - 16 (1 bit)
Enumeration:
0 : Disabled
Disabled
2 : High
Sense for high level
3 : Low
Sense for low level
End of enumeration elements list.
Description collection: Configuration of GPIO pins
address_offset : 0x6338 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DIR : Pin direction. Same physical register as DIR register
bits : 0 - -1 (0 bit)
Enumeration:
0 : Input
Configure pin as an input pin
1 : Output
Configure pin as an output pin
End of enumeration elements list.
INPUT : Connect or disconnect input buffer
bits : 1 - 0 (0 bit)
Enumeration:
0 : Connect
Connect input buffer
1 : Disconnect
Disconnect input buffer
End of enumeration elements list.
PULL : Pull configuration
bits : 2 - 2 (1 bit)
Enumeration:
0 : Disabled
No pull
1 : Pulldown
Pull down on pin
3 : Pullup
Pull up on pin
End of enumeration elements list.
DRIVE : Drive configuration
bits : 8 - 9 (2 bit)
Enumeration:
0 : S0S1
Standard '0', standard '1'
1 : H0S1
High drive '0', standard '1'
2 : S0H1
Standard '0', high drive '1'
3 : H0H1
High drive '0', high 'drive '1''
4 : D0S1
Disconnect '0' standard '1' (normally used for wired-or connections)
5 : D0H1
Disconnect '0', high drive '1' (normally used for wired-or connections)
6 : S0D1
Standard '0'. disconnect '1' (normally used for wired-and connections)
7 : H0D1
High drive '0', disconnect '1' (normally used for wired-and connections)
End of enumeration elements list.
SENSE : Pin sensing mechanism
bits : 16 - 16 (1 bit)
Enumeration:
0 : Disabled
Disabled
2 : High
Sense for high level
3 : Low
Sense for low level
End of enumeration elements list.
Description collection: Configuration of GPIO pins
address_offset : 0x6A6C Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DIR : Pin direction. Same physical register as DIR register
bits : 0 - -1 (0 bit)
Enumeration:
0 : Input
Configure pin as an input pin
1 : Output
Configure pin as an output pin
End of enumeration elements list.
INPUT : Connect or disconnect input buffer
bits : 1 - 0 (0 bit)
Enumeration:
0 : Connect
Connect input buffer
1 : Disconnect
Disconnect input buffer
End of enumeration elements list.
PULL : Pull configuration
bits : 2 - 2 (1 bit)
Enumeration:
0 : Disabled
No pull
1 : Pulldown
Pull down on pin
3 : Pullup
Pull up on pin
End of enumeration elements list.
DRIVE : Drive configuration
bits : 8 - 9 (2 bit)
Enumeration:
0 : S0S1
Standard '0', standard '1'
1 : H0S1
High drive '0', standard '1'
2 : S0H1
Standard '0', high drive '1'
3 : H0H1
High drive '0', high 'drive '1''
4 : D0S1
Disconnect '0' standard '1' (normally used for wired-or connections)
5 : D0H1
Disconnect '0', high drive '1' (normally used for wired-or connections)
6 : S0D1
Standard '0'. disconnect '1' (normally used for wired-and connections)
7 : H0D1
High drive '0', disconnect '1' (normally used for wired-and connections)
End of enumeration elements list.
SENSE : Pin sensing mechanism
bits : 16 - 16 (1 bit)
Enumeration:
0 : Disabled
Disabled
2 : High
Sense for high level
3 : Low
Sense for low level
End of enumeration elements list.
Description collection: Configuration of GPIO pins
address_offset : 0x71A4 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DIR : Pin direction. Same physical register as DIR register
bits : 0 - -1 (0 bit)
Enumeration:
0 : Input
Configure pin as an input pin
1 : Output
Configure pin as an output pin
End of enumeration elements list.
INPUT : Connect or disconnect input buffer
bits : 1 - 0 (0 bit)
Enumeration:
0 : Connect
Connect input buffer
1 : Disconnect
Disconnect input buffer
End of enumeration elements list.
PULL : Pull configuration
bits : 2 - 2 (1 bit)
Enumeration:
0 : Disabled
No pull
1 : Pulldown
Pull down on pin
3 : Pullup
Pull up on pin
End of enumeration elements list.
DRIVE : Drive configuration
bits : 8 - 9 (2 bit)
Enumeration:
0 : S0S1
Standard '0', standard '1'
1 : H0S1
High drive '0', standard '1'
2 : S0H1
Standard '0', high drive '1'
3 : H0H1
High drive '0', high 'drive '1''
4 : D0S1
Disconnect '0' standard '1' (normally used for wired-or connections)
5 : D0H1
Disconnect '0', high drive '1' (normally used for wired-or connections)
6 : S0D1
Standard '0'. disconnect '1' (normally used for wired-and connections)
7 : H0D1
High drive '0', disconnect '1' (normally used for wired-and connections)
End of enumeration elements list.
SENSE : Pin sensing mechanism
bits : 16 - 16 (1 bit)
Enumeration:
0 : Disabled
Disabled
2 : High
Sense for high level
3 : Low
Sense for low level
End of enumeration elements list.
Description collection: Configuration of GPIO pins
address_offset : 0x78E0 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DIR : Pin direction. Same physical register as DIR register
bits : 0 - -1 (0 bit)
Enumeration:
0 : Input
Configure pin as an input pin
1 : Output
Configure pin as an output pin
End of enumeration elements list.
INPUT : Connect or disconnect input buffer
bits : 1 - 0 (0 bit)
Enumeration:
0 : Connect
Connect input buffer
1 : Disconnect
Disconnect input buffer
End of enumeration elements list.
PULL : Pull configuration
bits : 2 - 2 (1 bit)
Enumeration:
0 : Disabled
No pull
1 : Pulldown
Pull down on pin
3 : Pullup
Pull up on pin
End of enumeration elements list.
DRIVE : Drive configuration
bits : 8 - 9 (2 bit)
Enumeration:
0 : S0S1
Standard '0', standard '1'
1 : H0S1
High drive '0', standard '1'
2 : S0H1
Standard '0', high drive '1'
3 : H0H1
High drive '0', high 'drive '1''
4 : D0S1
Disconnect '0' standard '1' (normally used for wired-or connections)
5 : D0H1
Disconnect '0', high drive '1' (normally used for wired-or connections)
6 : S0D1
Standard '0'. disconnect '1' (normally used for wired-and connections)
7 : H0D1
High drive '0', disconnect '1' (normally used for wired-and connections)
End of enumeration elements list.
SENSE : Pin sensing mechanism
bits : 16 - 16 (1 bit)
Enumeration:
0 : Disabled
Disabled
2 : High
Sense for high level
3 : Low
Sense for low level
End of enumeration elements list.
Description collection: Configuration of GPIO pins
address_offset : 0x8020 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DIR : Pin direction. Same physical register as DIR register
bits : 0 - -1 (0 bit)
Enumeration:
0 : Input
Configure pin as an input pin
1 : Output
Configure pin as an output pin
End of enumeration elements list.
INPUT : Connect or disconnect input buffer
bits : 1 - 0 (0 bit)
Enumeration:
0 : Connect
Connect input buffer
1 : Disconnect
Disconnect input buffer
End of enumeration elements list.
PULL : Pull configuration
bits : 2 - 2 (1 bit)
Enumeration:
0 : Disabled
No pull
1 : Pulldown
Pull down on pin
3 : Pullup
Pull up on pin
End of enumeration elements list.
DRIVE : Drive configuration
bits : 8 - 9 (2 bit)
Enumeration:
0 : S0S1
Standard '0', standard '1'
1 : H0S1
High drive '0', standard '1'
2 : S0H1
Standard '0', high drive '1'
3 : H0H1
High drive '0', high 'drive '1''
4 : D0S1
Disconnect '0' standard '1' (normally used for wired-or connections)
5 : D0H1
Disconnect '0', high drive '1' (normally used for wired-or connections)
6 : S0D1
Standard '0'. disconnect '1' (normally used for wired-and connections)
7 : H0D1
High drive '0', disconnect '1' (normally used for wired-and connections)
End of enumeration elements list.
SENSE : Pin sensing mechanism
bits : 16 - 16 (1 bit)
Enumeration:
0 : Disabled
Disabled
2 : High
Sense for high level
3 : Low
Sense for low level
End of enumeration elements list.
Description collection: Configuration of GPIO pins
address_offset : 0x8764 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DIR : Pin direction. Same physical register as DIR register
bits : 0 - -1 (0 bit)
Enumeration:
0 : Input
Configure pin as an input pin
1 : Output
Configure pin as an output pin
End of enumeration elements list.
INPUT : Connect or disconnect input buffer
bits : 1 - 0 (0 bit)
Enumeration:
0 : Connect
Connect input buffer
1 : Disconnect
Disconnect input buffer
End of enumeration elements list.
PULL : Pull configuration
bits : 2 - 2 (1 bit)
Enumeration:
0 : Disabled
No pull
1 : Pulldown
Pull down on pin
3 : Pullup
Pull up on pin
End of enumeration elements list.
DRIVE : Drive configuration
bits : 8 - 9 (2 bit)
Enumeration:
0 : S0S1
Standard '0', standard '1'
1 : H0S1
High drive '0', standard '1'
2 : S0H1
Standard '0', high drive '1'
3 : H0H1
High drive '0', high 'drive '1''
4 : D0S1
Disconnect '0' standard '1' (normally used for wired-or connections)
5 : D0H1
Disconnect '0', high drive '1' (normally used for wired-or connections)
6 : S0D1
Standard '0'. disconnect '1' (normally used for wired-and connections)
7 : H0D1
High drive '0', disconnect '1' (normally used for wired-and connections)
End of enumeration elements list.
SENSE : Pin sensing mechanism
bits : 16 - 16 (1 bit)
Enumeration:
0 : Disabled
Disabled
2 : High
Sense for high level
3 : Low
Sense for low level
End of enumeration elements list.
Description collection: Configuration of GPIO pins
address_offset : 0x8EAC Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DIR : Pin direction. Same physical register as DIR register
bits : 0 - -1 (0 bit)
Enumeration:
0 : Input
Configure pin as an input pin
1 : Output
Configure pin as an output pin
End of enumeration elements list.
INPUT : Connect or disconnect input buffer
bits : 1 - 0 (0 bit)
Enumeration:
0 : Connect
Connect input buffer
1 : Disconnect
Disconnect input buffer
End of enumeration elements list.
PULL : Pull configuration
bits : 2 - 2 (1 bit)
Enumeration:
0 : Disabled
No pull
1 : Pulldown
Pull down on pin
3 : Pullup
Pull up on pin
End of enumeration elements list.
DRIVE : Drive configuration
bits : 8 - 9 (2 bit)
Enumeration:
0 : S0S1
Standard '0', standard '1'
1 : H0S1
High drive '0', standard '1'
2 : S0H1
Standard '0', high drive '1'
3 : H0H1
High drive '0', high 'drive '1''
4 : D0S1
Disconnect '0' standard '1' (normally used for wired-or connections)
5 : D0H1
Disconnect '0', high drive '1' (normally used for wired-or connections)
6 : S0D1
Standard '0'. disconnect '1' (normally used for wired-and connections)
7 : H0D1
High drive '0', disconnect '1' (normally used for wired-and connections)
End of enumeration elements list.
SENSE : Pin sensing mechanism
bits : 16 - 16 (1 bit)
Enumeration:
0 : Disabled
Disabled
2 : High
Sense for high level
3 : Low
Sense for low level
End of enumeration elements list.
Description collection: Configuration of GPIO pins
address_offset : 0x95F8 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DIR : Pin direction. Same physical register as DIR register
bits : 0 - -1 (0 bit)
Enumeration:
0 : Input
Configure pin as an input pin
1 : Output
Configure pin as an output pin
End of enumeration elements list.
INPUT : Connect or disconnect input buffer
bits : 1 - 0 (0 bit)
Enumeration:
0 : Connect
Connect input buffer
1 : Disconnect
Disconnect input buffer
End of enumeration elements list.
PULL : Pull configuration
bits : 2 - 2 (1 bit)
Enumeration:
0 : Disabled
No pull
1 : Pulldown
Pull down on pin
3 : Pullup
Pull up on pin
End of enumeration elements list.
DRIVE : Drive configuration
bits : 8 - 9 (2 bit)
Enumeration:
0 : S0S1
Standard '0', standard '1'
1 : H0S1
High drive '0', standard '1'
2 : S0H1
Standard '0', high drive '1'
3 : H0H1
High drive '0', high 'drive '1''
4 : D0S1
Disconnect '0' standard '1' (normally used for wired-or connections)
5 : D0H1
Disconnect '0', high drive '1' (normally used for wired-or connections)
6 : S0D1
Standard '0'. disconnect '1' (normally used for wired-and connections)
7 : H0D1
High drive '0', disconnect '1' (normally used for wired-and connections)
End of enumeration elements list.
SENSE : Pin sensing mechanism
bits : 16 - 16 (1 bit)
Enumeration:
0 : Disabled
Disabled
2 : High
Sense for high level
3 : Low
Sense for low level
End of enumeration elements list.
Description collection: Configuration of GPIO pins
address_offset : 0x9D48 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DIR : Pin direction. Same physical register as DIR register
bits : 0 - -1 (0 bit)
Enumeration:
0 : Input
Configure pin as an input pin
1 : Output
Configure pin as an output pin
End of enumeration elements list.
INPUT : Connect or disconnect input buffer
bits : 1 - 0 (0 bit)
Enumeration:
0 : Connect
Connect input buffer
1 : Disconnect
Disconnect input buffer
End of enumeration elements list.
PULL : Pull configuration
bits : 2 - 2 (1 bit)
Enumeration:
0 : Disabled
No pull
1 : Pulldown
Pull down on pin
3 : Pullup
Pull up on pin
End of enumeration elements list.
DRIVE : Drive configuration
bits : 8 - 9 (2 bit)
Enumeration:
0 : S0S1
Standard '0', standard '1'
1 : H0S1
High drive '0', standard '1'
2 : S0H1
Standard '0', high drive '1'
3 : H0H1
High drive '0', high 'drive '1''
4 : D0S1
Disconnect '0' standard '1' (normally used for wired-or connections)
5 : D0H1
Disconnect '0', high drive '1' (normally used for wired-or connections)
6 : S0D1
Standard '0'. disconnect '1' (normally used for wired-and connections)
7 : H0D1
High drive '0', disconnect '1' (normally used for wired-and connections)
End of enumeration elements list.
SENSE : Pin sensing mechanism
bits : 16 - 16 (1 bit)
Enumeration:
0 : Disabled
Disabled
2 : High
Sense for high level
3 : Low
Sense for low level
End of enumeration elements list.
Description collection: Configuration of GPIO pins
address_offset : 0xA49C Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DIR : Pin direction. Same physical register as DIR register
bits : 0 - -1 (0 bit)
Enumeration:
0 : Input
Configure pin as an input pin
1 : Output
Configure pin as an output pin
End of enumeration elements list.
INPUT : Connect or disconnect input buffer
bits : 1 - 0 (0 bit)
Enumeration:
0 : Connect
Connect input buffer
1 : Disconnect
Disconnect input buffer
End of enumeration elements list.
PULL : Pull configuration
bits : 2 - 2 (1 bit)
Enumeration:
0 : Disabled
No pull
1 : Pulldown
Pull down on pin
3 : Pullup
Pull up on pin
End of enumeration elements list.
DRIVE : Drive configuration
bits : 8 - 9 (2 bit)
Enumeration:
0 : S0S1
Standard '0', standard '1'
1 : H0S1
High drive '0', standard '1'
2 : S0H1
Standard '0', high drive '1'
3 : H0H1
High drive '0', high 'drive '1''
4 : D0S1
Disconnect '0' standard '1' (normally used for wired-or connections)
5 : D0H1
Disconnect '0', high drive '1' (normally used for wired-or connections)
6 : S0D1
Standard '0'. disconnect '1' (normally used for wired-and connections)
7 : H0D1
High drive '0', disconnect '1' (normally used for wired-and connections)
End of enumeration elements list.
SENSE : Pin sensing mechanism
bits : 16 - 16 (1 bit)
Enumeration:
0 : Disabled
Disabled
2 : High
Sense for high level
3 : Low
Sense for low level
End of enumeration elements list.
Description collection: Configuration of GPIO pins
address_offset : 0xABF4 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DIR : Pin direction. Same physical register as DIR register
bits : 0 - -1 (0 bit)
Enumeration:
0 : Input
Configure pin as an input pin
1 : Output
Configure pin as an output pin
End of enumeration elements list.
INPUT : Connect or disconnect input buffer
bits : 1 - 0 (0 bit)
Enumeration:
0 : Connect
Connect input buffer
1 : Disconnect
Disconnect input buffer
End of enumeration elements list.
PULL : Pull configuration
bits : 2 - 2 (1 bit)
Enumeration:
0 : Disabled
No pull
1 : Pulldown
Pull down on pin
3 : Pullup
Pull up on pin
End of enumeration elements list.
DRIVE : Drive configuration
bits : 8 - 9 (2 bit)
Enumeration:
0 : S0S1
Standard '0', standard '1'
1 : H0S1
High drive '0', standard '1'
2 : S0H1
Standard '0', high drive '1'
3 : H0H1
High drive '0', high 'drive '1''
4 : D0S1
Disconnect '0' standard '1' (normally used for wired-or connections)
5 : D0H1
Disconnect '0', high drive '1' (normally used for wired-or connections)
6 : S0D1
Standard '0'. disconnect '1' (normally used for wired-and connections)
7 : H0D1
High drive '0', disconnect '1' (normally used for wired-and connections)
End of enumeration elements list.
SENSE : Pin sensing mechanism
bits : 16 - 16 (1 bit)
Enumeration:
0 : Disabled
Disabled
2 : High
Sense for high level
3 : Low
Sense for low level
End of enumeration elements list.
Description collection: Configuration of GPIO pins
address_offset : 0xB350 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DIR : Pin direction. Same physical register as DIR register
bits : 0 - -1 (0 bit)
Enumeration:
0 : Input
Configure pin as an input pin
1 : Output
Configure pin as an output pin
End of enumeration elements list.
INPUT : Connect or disconnect input buffer
bits : 1 - 0 (0 bit)
Enumeration:
0 : Connect
Connect input buffer
1 : Disconnect
Disconnect input buffer
End of enumeration elements list.
PULL : Pull configuration
bits : 2 - 2 (1 bit)
Enumeration:
0 : Disabled
No pull
1 : Pulldown
Pull down on pin
3 : Pullup
Pull up on pin
End of enumeration elements list.
DRIVE : Drive configuration
bits : 8 - 9 (2 bit)
Enumeration:
0 : S0S1
Standard '0', standard '1'
1 : H0S1
High drive '0', standard '1'
2 : S0H1
Standard '0', high drive '1'
3 : H0H1
High drive '0', high 'drive '1''
4 : D0S1
Disconnect '0' standard '1' (normally used for wired-or connections)
5 : D0H1
Disconnect '0', high drive '1' (normally used for wired-or connections)
6 : S0D1
Standard '0'. disconnect '1' (normally used for wired-and connections)
7 : H0D1
High drive '0', disconnect '1' (normally used for wired-and connections)
End of enumeration elements list.
SENSE : Pin sensing mechanism
bits : 16 - 16 (1 bit)
Enumeration:
0 : Disabled
Disabled
2 : High
Sense for high level
3 : Low
Sense for low level
End of enumeration elements list.
Description collection: Configuration of GPIO pins
address_offset : 0xBAB0 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DIR : Pin direction. Same physical register as DIR register
bits : 0 - -1 (0 bit)
Enumeration:
0 : Input
Configure pin as an input pin
1 : Output
Configure pin as an output pin
End of enumeration elements list.
INPUT : Connect or disconnect input buffer
bits : 1 - 0 (0 bit)
Enumeration:
0 : Connect
Connect input buffer
1 : Disconnect
Disconnect input buffer
End of enumeration elements list.
PULL : Pull configuration
bits : 2 - 2 (1 bit)
Enumeration:
0 : Disabled
No pull
1 : Pulldown
Pull down on pin
3 : Pullup
Pull up on pin
End of enumeration elements list.
DRIVE : Drive configuration
bits : 8 - 9 (2 bit)
Enumeration:
0 : S0S1
Standard '0', standard '1'
1 : H0S1
High drive '0', standard '1'
2 : S0H1
Standard '0', high drive '1'
3 : H0H1
High drive '0', high 'drive '1''
4 : D0S1
Disconnect '0' standard '1' (normally used for wired-or connections)
5 : D0H1
Disconnect '0', high drive '1' (normally used for wired-or connections)
6 : S0D1
Standard '0'. disconnect '1' (normally used for wired-and connections)
7 : H0D1
High drive '0', disconnect '1' (normally used for wired-and connections)
End of enumeration elements list.
SENSE : Pin sensing mechanism
bits : 16 - 16 (1 bit)
Enumeration:
0 : Disabled
Disabled
2 : High
Sense for high level
3 : Low
Sense for low level
End of enumeration elements list.
Description collection: Configuration of GPIO pins
address_offset : 0xC214 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DIR : Pin direction. Same physical register as DIR register
bits : 0 - -1 (0 bit)
Enumeration:
0 : Input
Configure pin as an input pin
1 : Output
Configure pin as an output pin
End of enumeration elements list.
INPUT : Connect or disconnect input buffer
bits : 1 - 0 (0 bit)
Enumeration:
0 : Connect
Connect input buffer
1 : Disconnect
Disconnect input buffer
End of enumeration elements list.
PULL : Pull configuration
bits : 2 - 2 (1 bit)
Enumeration:
0 : Disabled
No pull
1 : Pulldown
Pull down on pin
3 : Pullup
Pull up on pin
End of enumeration elements list.
DRIVE : Drive configuration
bits : 8 - 9 (2 bit)
Enumeration:
0 : S0S1
Standard '0', standard '1'
1 : H0S1
High drive '0', standard '1'
2 : S0H1
Standard '0', high drive '1'
3 : H0H1
High drive '0', high 'drive '1''
4 : D0S1
Disconnect '0' standard '1' (normally used for wired-or connections)
5 : D0H1
Disconnect '0', high drive '1' (normally used for wired-or connections)
6 : S0D1
Standard '0'. disconnect '1' (normally used for wired-and connections)
7 : H0D1
High drive '0', disconnect '1' (normally used for wired-and connections)
End of enumeration elements list.
SENSE : Pin sensing mechanism
bits : 16 - 16 (1 bit)
Enumeration:
0 : Disabled
Disabled
2 : High
Sense for high level
3 : Low
Sense for low level
End of enumeration elements list.
Description collection: Configuration of GPIO pins
address_offset : 0xC97C Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DIR : Pin direction. Same physical register as DIR register
bits : 0 - -1 (0 bit)
Enumeration:
0 : Input
Configure pin as an input pin
1 : Output
Configure pin as an output pin
End of enumeration elements list.
INPUT : Connect or disconnect input buffer
bits : 1 - 0 (0 bit)
Enumeration:
0 : Connect
Connect input buffer
1 : Disconnect
Disconnect input buffer
End of enumeration elements list.
PULL : Pull configuration
bits : 2 - 2 (1 bit)
Enumeration:
0 : Disabled
No pull
1 : Pulldown
Pull down on pin
3 : Pullup
Pull up on pin
End of enumeration elements list.
DRIVE : Drive configuration
bits : 8 - 9 (2 bit)
Enumeration:
0 : S0S1
Standard '0', standard '1'
1 : H0S1
High drive '0', standard '1'
2 : S0H1
Standard '0', high drive '1'
3 : H0H1
High drive '0', high 'drive '1''
4 : D0S1
Disconnect '0' standard '1' (normally used for wired-or connections)
5 : D0H1
Disconnect '0', high drive '1' (normally used for wired-or connections)
6 : S0D1
Standard '0'. disconnect '1' (normally used for wired-and connections)
7 : H0D1
High drive '0', disconnect '1' (normally used for wired-and connections)
End of enumeration elements list.
SENSE : Pin sensing mechanism
bits : 16 - 16 (1 bit)
Enumeration:
0 : Disabled
Disabled
2 : High
Sense for high level
3 : Low
Sense for low level
End of enumeration elements list.
Description collection: Configuration of GPIO pins
address_offset : 0xD0E8 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DIR : Pin direction. Same physical register as DIR register
bits : 0 - -1 (0 bit)
Enumeration:
0 : Input
Configure pin as an input pin
1 : Output
Configure pin as an output pin
End of enumeration elements list.
INPUT : Connect or disconnect input buffer
bits : 1 - 0 (0 bit)
Enumeration:
0 : Connect
Connect input buffer
1 : Disconnect
Disconnect input buffer
End of enumeration elements list.
PULL : Pull configuration
bits : 2 - 2 (1 bit)
Enumeration:
0 : Disabled
No pull
1 : Pulldown
Pull down on pin
3 : Pullup
Pull up on pin
End of enumeration elements list.
DRIVE : Drive configuration
bits : 8 - 9 (2 bit)
Enumeration:
0 : S0S1
Standard '0', standard '1'
1 : H0S1
High drive '0', standard '1'
2 : S0H1
Standard '0', high drive '1'
3 : H0H1
High drive '0', high 'drive '1''
4 : D0S1
Disconnect '0' standard '1' (normally used for wired-or connections)
5 : D0H1
Disconnect '0', high drive '1' (normally used for wired-or connections)
6 : S0D1
Standard '0'. disconnect '1' (normally used for wired-and connections)
7 : H0D1
High drive '0', disconnect '1' (normally used for wired-and connections)
End of enumeration elements list.
SENSE : Pin sensing mechanism
bits : 16 - 16 (1 bit)
Enumeration:
0 : Disabled
Disabled
2 : High
Sense for high level
3 : Low
Sense for low level
End of enumeration elements list.
Description collection: Configuration of GPIO pins
address_offset : 0xD858 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DIR : Pin direction. Same physical register as DIR register
bits : 0 - -1 (0 bit)
Enumeration:
0 : Input
Configure pin as an input pin
1 : Output
Configure pin as an output pin
End of enumeration elements list.
INPUT : Connect or disconnect input buffer
bits : 1 - 0 (0 bit)
Enumeration:
0 : Connect
Connect input buffer
1 : Disconnect
Disconnect input buffer
End of enumeration elements list.
PULL : Pull configuration
bits : 2 - 2 (1 bit)
Enumeration:
0 : Disabled
No pull
1 : Pulldown
Pull down on pin
3 : Pullup
Pull up on pin
End of enumeration elements list.
DRIVE : Drive configuration
bits : 8 - 9 (2 bit)
Enumeration:
0 : S0S1
Standard '0', standard '1'
1 : H0S1
High drive '0', standard '1'
2 : S0H1
Standard '0', high drive '1'
3 : H0H1
High drive '0', high 'drive '1''
4 : D0S1
Disconnect '0' standard '1' (normally used for wired-or connections)
5 : D0H1
Disconnect '0', high drive '1' (normally used for wired-or connections)
6 : S0D1
Standard '0'. disconnect '1' (normally used for wired-and connections)
7 : H0D1
High drive '0', disconnect '1' (normally used for wired-and connections)
End of enumeration elements list.
SENSE : Pin sensing mechanism
bits : 16 - 16 (1 bit)
Enumeration:
0 : Disabled
Disabled
2 : High
Sense for high level
3 : Low
Sense for low level
End of enumeration elements list.
Description collection: Configuration of GPIO pins
address_offset : 0xDFCC Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DIR : Pin direction. Same physical register as DIR register
bits : 0 - -1 (0 bit)
Enumeration:
0 : Input
Configure pin as an input pin
1 : Output
Configure pin as an output pin
End of enumeration elements list.
INPUT : Connect or disconnect input buffer
bits : 1 - 0 (0 bit)
Enumeration:
0 : Connect
Connect input buffer
1 : Disconnect
Disconnect input buffer
End of enumeration elements list.
PULL : Pull configuration
bits : 2 - 2 (1 bit)
Enumeration:
0 : Disabled
No pull
1 : Pulldown
Pull down on pin
3 : Pullup
Pull up on pin
End of enumeration elements list.
DRIVE : Drive configuration
bits : 8 - 9 (2 bit)
Enumeration:
0 : S0S1
Standard '0', standard '1'
1 : H0S1
High drive '0', standard '1'
2 : S0H1
Standard '0', high drive '1'
3 : H0H1
High drive '0', high 'drive '1''
4 : D0S1
Disconnect '0' standard '1' (normally used for wired-or connections)
5 : D0H1
Disconnect '0', high drive '1' (normally used for wired-or connections)
6 : S0D1
Standard '0'. disconnect '1' (normally used for wired-and connections)
7 : H0D1
High drive '0', disconnect '1' (normally used for wired-and connections)
End of enumeration elements list.
SENSE : Pin sensing mechanism
bits : 16 - 16 (1 bit)
Enumeration:
0 : Disabled
Disabled
2 : High
Sense for high level
3 : Low
Sense for low level
End of enumeration elements list.
Description collection: Configuration of GPIO pins
address_offset : 0xE00 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DIR : Pin direction. Same physical register as DIR register
bits : 0 - -1 (0 bit)
Enumeration:
0 : Input
Configure pin as an input pin
1 : Output
Configure pin as an output pin
End of enumeration elements list.
INPUT : Connect or disconnect input buffer
bits : 1 - 0 (0 bit)
Enumeration:
0 : Connect
Connect input buffer
1 : Disconnect
Disconnect input buffer
End of enumeration elements list.
PULL : Pull configuration
bits : 2 - 2 (1 bit)
Enumeration:
0 : Disabled
No pull
1 : Pulldown
Pull down on pin
3 : Pullup
Pull up on pin
End of enumeration elements list.
DRIVE : Drive configuration
bits : 8 - 9 (2 bit)
Enumeration:
0 : S0S1
Standard '0', standard '1'
1 : H0S1
High drive '0', standard '1'
2 : S0H1
Standard '0', high drive '1'
3 : H0H1
High drive '0', high 'drive '1''
4 : D0S1
Disconnect '0' standard '1' (normally used for wired-or connections)
5 : D0H1
Disconnect '0', high drive '1' (normally used for wired-or connections)
6 : S0D1
Standard '0'. disconnect '1' (normally used for wired-and connections)
7 : H0D1
High drive '0', disconnect '1' (normally used for wired-and connections)
End of enumeration elements list.
SENSE : Pin sensing mechanism
bits : 16 - 16 (1 bit)
Enumeration:
0 : Disabled
Disabled
2 : High
Sense for high level
3 : Low
Sense for low level
End of enumeration elements list.
Description collection: Configuration of GPIO pins
address_offset : 0xE744 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DIR : Pin direction. Same physical register as DIR register
bits : 0 - -1 (0 bit)
Enumeration:
0 : Input
Configure pin as an input pin
1 : Output
Configure pin as an output pin
End of enumeration elements list.
INPUT : Connect or disconnect input buffer
bits : 1 - 0 (0 bit)
Enumeration:
0 : Connect
Connect input buffer
1 : Disconnect
Disconnect input buffer
End of enumeration elements list.
PULL : Pull configuration
bits : 2 - 2 (1 bit)
Enumeration:
0 : Disabled
No pull
1 : Pulldown
Pull down on pin
3 : Pullup
Pull up on pin
End of enumeration elements list.
DRIVE : Drive configuration
bits : 8 - 9 (2 bit)
Enumeration:
0 : S0S1
Standard '0', standard '1'
1 : H0S1
High drive '0', standard '1'
2 : S0H1
Standard '0', high drive '1'
3 : H0H1
High drive '0', high 'drive '1''
4 : D0S1
Disconnect '0' standard '1' (normally used for wired-or connections)
5 : D0H1
Disconnect '0', high drive '1' (normally used for wired-or connections)
6 : S0D1
Standard '0'. disconnect '1' (normally used for wired-and connections)
7 : H0D1
High drive '0', disconnect '1' (normally used for wired-and connections)
End of enumeration elements list.
SENSE : Pin sensing mechanism
bits : 16 - 16 (1 bit)
Enumeration:
0 : Disabled
Disabled
2 : High
Sense for high level
3 : Low
Sense for low level
End of enumeration elements list.
Description collection: Configuration of GPIO pins
address_offset : 0xEEC0 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DIR : Pin direction. Same physical register as DIR register
bits : 0 - -1 (0 bit)
Enumeration:
0 : Input
Configure pin as an input pin
1 : Output
Configure pin as an output pin
End of enumeration elements list.
INPUT : Connect or disconnect input buffer
bits : 1 - 0 (0 bit)
Enumeration:
0 : Connect
Connect input buffer
1 : Disconnect
Disconnect input buffer
End of enumeration elements list.
PULL : Pull configuration
bits : 2 - 2 (1 bit)
Enumeration:
0 : Disabled
No pull
1 : Pulldown
Pull down on pin
3 : Pullup
Pull up on pin
End of enumeration elements list.
DRIVE : Drive configuration
bits : 8 - 9 (2 bit)
Enumeration:
0 : S0S1
Standard '0', standard '1'
1 : H0S1
High drive '0', standard '1'
2 : S0H1
Standard '0', high drive '1'
3 : H0H1
High drive '0', high 'drive '1''
4 : D0S1
Disconnect '0' standard '1' (normally used for wired-or connections)
5 : D0H1
Disconnect '0', high drive '1' (normally used for wired-or connections)
6 : S0D1
Standard '0'. disconnect '1' (normally used for wired-and connections)
7 : H0D1
High drive '0', disconnect '1' (normally used for wired-and connections)
End of enumeration elements list.
SENSE : Pin sensing mechanism
bits : 16 - 16 (1 bit)
Enumeration:
0 : Disabled
Disabled
2 : High
Sense for high level
3 : Low
Sense for low level
End of enumeration elements list.
Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !
This website is sponsored by Embeetle, an IDE designed from scratch for embedded software developers.