\n

IOCON

Peripheral Memory Blocks

address_offset : 0x0 Bytes (0x0)
size : 0xFFF byte (0x0)
mem_usage : registers
protection : not protected

Registers

PIO2_6

PIO0_1

PIO1_8

SSEL1_LOC

PIO0_2

PIO2_7

PIO2_8

PIO2_1

PIO0_3

PIO0_4

PIO0_5

PIO1_9

PIO3_4

PIO2_4

PIO2_5

PIO3_5

PIO0_6

PIO0_7

PIO2_9

PIO2_10

PIO2_2

PIO0_8

PIO0_9

SWCLK_PIO0_10

PIO1_10

PIO2_11

R_PIO0_11

R_PIO1_0

R_PIO1_1

PIO2_0

R_PIO1_2

PIO3_0

PIO3_1

PIO2_3

SWDIO_PIO1_3

PIO1_4

PIO1_11

PIO3_2

PIO1_5

PIO1_6

PIO1_7

PIO3_3

SCK0_LOC

DSR_LOC

DCD_LOC

RI_LOC

RESET_PIO0_0

CT16B0_CAP0_LOC

SCK1_LOC

MISO1_LOC

MOSI1_LOC

CT32B0_CAP0_LOC

RXD_LOC


PIO2_6

I/O configuration for pin PIO2_6/ CT32B0_MAT1
address_offset : 0x0 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO2_6 PIO2_6 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE HYS RESERVED RESERVED OD

FUNC : Selects pin function. All other values are reserved.
bits : 0 - 2 (3 bit)

Enumeration: ENUM

0x0 : SELECTS_FUNCTION_PIO

Selects function PIO2_6.

0x1 : SELECTS_FUNCTION_CT3

Selects function CT32B0_MAT1.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)

Enumeration: ENUM

0x0 : INACTIVE_NO_PULL_DO

Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN_RESISTOR_E

Pull-down resistor enabled.

0x2 : PULL_UP_RESISTOR_ENA

Pull-up resistor enabled.

0x3 : REPEATER_MODE_

Repeater mode.

End of enumeration elements list.

HYS : Hysteresis.
bits : 5 - 10 (6 bit)

Enumeration: ENUM

0 : DISABLE_

Disable.

1 : ENABLE_

Enable.

End of enumeration elements list.

RESERVED : Reserved
bits : 6 - 15 (10 bit)

RESERVED : Reserved
bits : 6 - 15 (10 bit)

OD : Selects pseudo open-drain mode.
bits : 10 - 20 (11 bit)

Enumeration: ENUM

0 : STANDARD_GPIO_OUTPUT

Standard GPIO output

1 : OPEN_DRAIN_OUTPUT

Open-drain output

End of enumeration elements list.


PIO0_1

I/O configuration for pin PIO0_1/CLKOUT/CT32B0_MAT2
address_offset : 0x10 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO0_1 PIO0_1 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE HYS RESERVED RESERVED OD

FUNC : Selects pin function. All other values are reserved.
bits : 0 - 2 (3 bit)

Enumeration: ENUM

0x0 : SELECTS_FUNCTION_PIO

Selects function PIO0_1.

0x1 : SELECTS_FUNCTION_CLK

Selects function CLKOUT.

0x2 : SELECTS_FUNCTION_CT3

Selects function CT32B0_MAT2.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)

Enumeration: ENUM

0x0 : INACTIVE_NO_PULL_DO

Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN_RESISTOR_E

Pull-down resistor enabled.

0x2 : PULL_UP_RESISTOR_ENA

Pull-up resistor enabled.

0x3 : REPEATER_MODE_

Repeater mode.

End of enumeration elements list.

HYS : Hysteresis.
bits : 5 - 10 (6 bit)

Enumeration: ENUM

0 : DISABLE_

Disable.

1 : ENABLE_

Enable.

End of enumeration elements list.

RESERVED : Reserved
bits : 6 - 15 (10 bit)

RESERVED : Reserved
bits : 6 - 15 (10 bit)

OD : Selects pseudo open-drain mode.
bits : 10 - 20 (11 bit)

Enumeration: ENUM

0 : STANDARD_GPIO_OUTPUT

Standard GPIO output

1 : OPEN_DRAIN_OUTPUT

Open-drain output

End of enumeration elements list.


PIO1_8

I/O configuration for pin PIO1_8/CT16B1_CAP0
address_offset : 0x14 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO1_8 PIO1_8 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE HYS RESERVED RESERVED OD

FUNC : Selects pin function. All other values are reserved.
bits : 0 - 2 (3 bit)

Enumeration: ENUM

0x0 : SELECTS_FUNCTION_PIO

Selects function PIO1_8.

0x1 : SELECTS_FUNCTION_CT1

Selects function CT16B1_CAP0.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)

Enumeration: ENUM

0x0 : INACTIVE_NO_PULL_DO

Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN_RESISTOR_E

Pull-down resistor enabled.

0x2 : PULL_UP_RESISTOR_ENA

Pull-up resistor enabled.

0x3 : REPEATER_MODE_

Repeater mode.

End of enumeration elements list.

HYS : Hysteresis.
bits : 5 - 10 (6 bit)

Enumeration: ENUM

0 : DISABLE_

Disable.

1 : ENABLE_

Enable.

End of enumeration elements list.

RESERVED : Reserved
bits : 6 - 15 (10 bit)

RESERVED : Reserved
bits : 6 - 15 (10 bit)

OD : Selects pseudo open-drain mode.
bits : 10 - 20 (11 bit)

Enumeration: ENUM

0 : STANDARD_GPIO_OUTPUT

Standard GPIO output

1 : OPEN_DRAIN_OUTPUT

Open-drain output

End of enumeration elements list.


SSEL1_LOC

SSEL1 pin location select register
address_offset : 0x18 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

SSEL1_LOC SSEL1_LOC read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SSEL1LOC RESERVED

SSEL1LOC : Selects pin location for SSEL1 function.
bits : 0 - 1 (2 bit)

Enumeration: ENUM

0x0 : SELECTS_SSEL1_FUNCTI

Selects SSEL1 function in pin location PIO2_2/DCD/MISO1 (see Table 126).

0x0 : SELECTS_SSEL1_FUNCTI

Selects SSEL1 function in pin location PIO2_2/DCD/MISO1 (see Table 126).

0x2 : RESERVED_

Reserved.

0x2 : RESERVED_

Reserved.

End of enumeration elements list.

RESERVED : Reserved.
bits : 2 - 33 (32 bit)


PIO0_2

I/O configuration for pin PIO0_2/SSEL0/CT16B0_CAP0
address_offset : 0x1C Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO0_2 PIO0_2 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE HYS RESERVED RESERVED OD

FUNC : Selects pin function. All other values are reserved.
bits : 0 - 2 (3 bit)

Enumeration: ENUM

0x0 : SELECTS_FUNCTION_PIO

Selects function PIO0_2.

0x1 : SELECTS_FUNCTION_SSE

Selects function SSEL0.

0x2 : SELECTS_FUNCTION_CT1

Selects function CT16B0_CAP0.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)

Enumeration: ENUM

0x0 : INACTIVE_NO_PULL_DO

Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN_RESISTOR_E

Pull-down resistor enabled.

0x2 : PULL_UP_RESISTOR_ENA

Pull-up resistor enabled.

0x3 : REPEATER_MODE_

Repeater mode.

End of enumeration elements list.

HYS : Hysteresis.
bits : 5 - 10 (6 bit)

Enumeration: ENUM

0 : DISABLE_

Disable.

1 : ENABLE_

Enable.

End of enumeration elements list.

RESERVED : Reserved
bits : 6 - 15 (10 bit)

RESERVED : Reserved
bits : 6 - 15 (10 bit)

OD : Selects pseudo open-drain mode.
bits : 10 - 20 (11 bit)

Enumeration: ENUM

0 : STANDARD_GPIO_OUTPUT

Standard GPIO output

1 : OPEN_DRAIN_OUTPUT

Open-drain output

End of enumeration elements list.


PIO2_7

I/O configuration for pin PIO2_7/ CT32B0_MAT2/RXD
address_offset : 0x20 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO2_7 PIO2_7 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE HYS RESERVED RESERVED OD

FUNC : Selects pin function. All other values are reserved.
bits : 0 - 2 (3 bit)

Enumeration: ENUM

0x0 : SELECTS_FUNCTION_PIO

Selects function PIO2_7.

0x1 : SELECTS_FUNCTION_CT3

Selects function CT32B0_MAT2.

0x2 : SELECTS_FUNCTION_RXD

Selects function RXD.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)

Enumeration: ENUM

0x0 : INACTIVE_NO_PULL_DO

Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN_RESISTOR_E

Pull-down resistor enabled.

0x2 : PULL_UP_RESISTOR_ENA

Pull-up resistor enabled.

0x3 : REPEATER_MODE_

Repeater mode.

End of enumeration elements list.

HYS : Hysteresis.
bits : 5 - 10 (6 bit)

Enumeration: ENUM

0 : DISABLE_

Disable.

1 : ENABLE_

Enable.

End of enumeration elements list.

RESERVED : Reserved
bits : 6 - 15 (10 bit)

RESERVED : Reserved
bits : 6 - 15 (10 bit)

OD : Selects pseudo open-drain mode.
bits : 10 - 20 (11 bit)

Enumeration: ENUM

0 : STANDARD_GPIO_OUTPUT

Standard GPIO output

1 : OPEN_DRAIN_OUTPUT

Open-drain output

End of enumeration elements list.


PIO2_8

I/O configuration for pin PIO2_8/ CT32B0_MAT3/TXD
address_offset : 0x24 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO2_8 PIO2_8 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE HYS RESERVED RESERVED OD

FUNC : Selects pin function. All other values are reserved.
bits : 0 - 2 (3 bit)

Enumeration: ENUM

0x0 : SELECTS_FUNCTION_PIO

Selects function PIO2_8.

0x1 : SELECTS_FUNCTION_CT3

Selects function CT32B0_MAT3.

0x2 : SELECTS_FUNCTION_TXD

Selects function TXD.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)

Enumeration: ENUM

0x0 : INACTIVE_NO_PULL_DO

Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN_RESISTOR_E

Pull-down resistor enabled.

0x2 : PULL_UP_RESISTOR_ENA

Pull-up resistor enabled.

0x3 : REPEATER_MODE_

Repeater mode.

End of enumeration elements list.

HYS : Hysteresis.
bits : 5 - 10 (6 bit)

Enumeration: ENUM

0 : DISABLE_

Disable.

1 : ENABLE_

Enable.

End of enumeration elements list.

RESERVED : Reserved
bits : 6 - 15 (10 bit)

RESERVED : Reserved
bits : 6 - 15 (10 bit)

OD : Selects pseudo open-drain mode.
bits : 10 - 20 (11 bit)

Enumeration: ENUM

0 : STANDARD_GPIO_OUTPUT

Standard GPIO output

1 : OPEN_DRAIN_OUTPUT

Open-drain output

End of enumeration elements list.


PIO2_1

I/O configuration for pin PIO2_1/DSR/SCK1
address_offset : 0x28 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO2_1 PIO2_1 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE HYS RESERVED RESERVED OD

FUNC : Selects pin function. All other values are reserved.
bits : 0 - 2 (3 bit)

Enumeration: ENUM

0x0 : SELECTS_FUNCTION_PIO

Selects function PIO2_1.

0x1 : SELECT_FUNCTION_DSR_

Select function DSR.

0x2 : SELECT_FUNCTION_SCK1

Select function SCK1.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)

Enumeration: ENUM

0x0 : INACTIVE_NO_PULL_DO

Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN_RESISTOR_E

Pull-down resistor enabled.

0x2 : PULL_UP_RESISTOR_ENA

Pull-up resistor enabled.

0x3 : REPEATER_MODE_

Repeater mode.

End of enumeration elements list.

HYS : Hysteresis.
bits : 5 - 10 (6 bit)

Enumeration: ENUM

0 : DISABLE_

Disable.

1 : ENABLE_

Enable.

End of enumeration elements list.

RESERVED : Reserved
bits : 6 - 15 (10 bit)

RESERVED : Reserved
bits : 6 - 15 (10 bit)

OD : Selects pseudo open-drain mode.
bits : 10 - 20 (11 bit)

Enumeration: ENUM

0 : STANDARD_GPIO_OUTPUT

Standard GPIO output

1 : OPEN_DRAIN_OUTPUT

Open-drain output

End of enumeration elements list.


PIO0_3

I/O configuration for pin PIO0_3
address_offset : 0x2C Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO0_3 PIO0_3 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE HYS RESERVED RESERVED OD

FUNC : Selects pin function. All other values are reserved.
bits : 0 - 2 (3 bit)

Enumeration: ENUM

0x0 : SELECTS_FUNCTION_PIO

Selects function PIO0_3.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)

Enumeration: ENUM

0x0 : INACTIVE_NO_PULL_DO

Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN_RESISTOR_E

Pull-down resistor enabled.

0x2 : PULL_UP_RESISTOR_ENA

Pull-up resistor enabled.

0x3 : REPEATER_MODE_

Repeater mode.

End of enumeration elements list.

HYS : Hysteresis.
bits : 5 - 10 (6 bit)

Enumeration: ENUM

0 : DISABLE_

Disable.

1 : ENABLE_

Enable.

End of enumeration elements list.

RESERVED : Reserved
bits : 6 - 15 (10 bit)

RESERVED : Reserved
bits : 6 - 15 (10 bit)

OD : Selects pseudo open-drain mode.
bits : 10 - 20 (11 bit)

Enumeration: ENUM

0 : STANDARD_GPIO_OUTPUT

Standard GPIO output

1 : OPEN_DRAIN_OUTPUT

Open-drain output

End of enumeration elements list.


PIO0_4

I/O configuration for pin PIO0_4/SCL
address_offset : 0x30 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO0_4 PIO0_4 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC I2CMODE RESERVED

FUNC : Selects pin function. All other values are reserved.
bits : 0 - 2 (3 bit)

Enumeration: ENUM

0x0 : SELECTS_FUNCTION_PIO

Selects function PIO0_4 (open-drain pin).

0x1 : SELECTS_I2C_FUNCTION

Selects I2C function SCL (open-drain pin).

End of enumeration elements list.

I2CMODE : Selects I2C mode. Select Standard mode (I2CMODE = 00, default) or Standard I/O functionality (I2CMODE = 01) if the pin function is GPIO (FUNC = 000).
bits : 8 - 17 (10 bit)

Enumeration: ENUM

0x0 : STANDARD_MODE_FAST

Standard mode/ Fast-mode I2C.

0x1 : STANDARD_IO_FUNCTION

Standard I/O functionality

0x2 : FAST_MODE_PLUS_I2C

Fast-mode Plus I2C

0x3 : RESERVED_

Reserved.

End of enumeration elements list.

RESERVED : Reserved.
bits : 10 - 41 (32 bit)


PIO0_5

I/O configuration for pin PIO0_5/SDA
address_offset : 0x34 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO0_5 PIO0_5 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC I2CMODE RESERVED

FUNC : Selects pin function. All other values are reserved.
bits : 0 - 2 (3 bit)

Enumeration: ENUM

0x0 : SELECTS_FUNCTION_PIO

Selects function PIO0_5 (open-drain pin).

0x1 : SELECTS_I2C_FUNCTION

Selects I2C function SDA (open-drain pin).

End of enumeration elements list.

I2CMODE : Selects I2C mode. Select Standard mode (I2CMODE = 00, default) or Standard I/O functionality (I2CMODE = 01) if the pin function is GPIO (FUNC = 000).
bits : 8 - 17 (10 bit)

Enumeration: ENUM

0x0 : STANDARD_MODE_FAST

Standard mode/ Fast-mode I2C.

0x1 : STANDARD_IO_FUNCTION

Standard I/O functionality

0x2 : FAST_MODE_PLUS_I2C

Fast-mode Plus I2C

0x3 : RESERVED_

Reserved.

End of enumeration elements list.

RESERVED : Reserved.
bits : 10 - 41 (32 bit)


PIO1_9

I/O configuration for pin PIO1_9/CT16B1_MAT0/ MOSI1
address_offset : 0x38 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO1_9 PIO1_9 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE HYS RESERVED RESERVED OD

FUNC : Selects pin function. All other values are reserved.
bits : 0 - 2 (3 bit)

Enumeration: ENUM

0x0 : SELECTS_FUNCTION_PIO

Selects function PIO1_9.

0x1 : SELECTS_FUNCTION_CT1

Selects function CT16B1_MAT0.

0x2 : SELECTS_FUNCTION_MOS

Selects function MOSI1.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)

Enumeration: ENUM

0x0 : INACTIVE_NO_PULL_DO

Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN_RESISTOR_E

Pull-down resistor enabled.

0x2 : PULL_UP_RESISTOR_ENA

Pull-up resistor enabled.

0x3 : REPEATER_MODE_

Repeater mode.

End of enumeration elements list.

HYS : Hysteresis.
bits : 5 - 10 (6 bit)

Enumeration: ENUM

0 : DISABLE_

Disable.

1 : ENABLE_

Enable.

End of enumeration elements list.

RESERVED : Reserved
bits : 6 - 15 (10 bit)

RESERVED : Reserved
bits : 6 - 15 (10 bit)

OD : Selects pseudo open-drain mode.
bits : 10 - 20 (11 bit)

Enumeration: ENUM

0 : STANDARD_GPIO_OUTPUT

Standard GPIO output

1 : OPEN_DRAIN_OUTPUT

Open-drain output

End of enumeration elements list.


PIO3_4

I/O configuration for pin PIO3_4/ CT16B0_CAP1/RXD
address_offset : 0x3C Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO3_4 PIO3_4 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE HYS RESERVED RESERVED OD

FUNC : Selects pin function. All other values are reserved.
bits : 0 - 2 (3 bit)

Enumeration: ENUM

0x0 : SELECTS_FUNCTION_PIO

Selects function PIO3_4.

0x1 : SELECTS_FUNCTION_CT1

Selects function CT16B0_CAP1.

0x2 : SELECTS_FUNCTION_RXD

Selects function RXD.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)

Enumeration: ENUM

0x0 : INACTIVE_NO_PULL_DO

Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN_RESISTOR_E

Pull-down resistor enabled.

0x2 : PULL_UP_RESISTOR_ENA

Pull-up resistor enabled.

0x3 : REPEATER_MODE_

Repeater mode.

End of enumeration elements list.

HYS : Hysteresis.
bits : 5 - 10 (6 bit)

Enumeration: ENUM

0 : DISABLE_

Disable.

1 : ENABLE_

Enable.

End of enumeration elements list.

RESERVED : Reserved
bits : 6 - 15 (10 bit)

RESERVED : Reserved
bits : 6 - 15 (10 bit)

OD : Selects pseudo open-drain mode.
bits : 10 - 20 (11 bit)

Enumeration: ENUM

0 : STANDARD_GPIO_OUTPUT

Standard GPIO output

1 : OPEN_DRAIN_OUTPUT

Open-drain output

End of enumeration elements list.


PIO2_4

I/O configuration for pin PIO2_4/ CT16B1_MAT1/ SSEL1
address_offset : 0x40 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO2_4 PIO2_4 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE HYS RESERVED RESERVED OD

FUNC : Selects pin function. All other values are reserved.
bits : 0 - 2 (3 bit)

Enumeration: ENUM

0x0 : SELECTS_FUNCTION_PIO

Selects function PIO2_4.

0x1 : SELECTS_FUNCTION_CT1

Selects function CT16B1_MAT1.

0x2 : SELECTS_FUNCTION_SSE

Selects function SSEL1.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)

Enumeration: ENUM

0x0 : INACTIVE_NO_PULL_DO

Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN_RESISTOR_E

Pull-down resistor enabled.

0x2 : PULL_UP_RESISTOR_ENA

Pull-up resistor enabled.

0x3 : REPEATER_MODE_

Repeater mode.

End of enumeration elements list.

HYS : Hysteresis.
bits : 5 - 10 (6 bit)

Enumeration: ENUM

0 : DISABLE_

Disable.

1 : ENABLE_

Enable.

End of enumeration elements list.

RESERVED : Reserved
bits : 6 - 15 (10 bit)

RESERVED : Reserved
bits : 6 - 15 (10 bit)

OD : Selects pseudo open-drain mode.
bits : 10 - 20 (11 bit)

Enumeration: ENUM

0 : STANDARD_GPIO_OUTPUT

Standard GPIO output

1 : OPEN_DRAIN_OUTPUT

Open-drain output

End of enumeration elements list.


PIO2_5

I/O configuration for pin PIO2_5/ CT32B0_MAT0
address_offset : 0x44 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO2_5 PIO2_5 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE HYS RESERVED RESERVED OD

FUNC : Selects pin function. All other values are reserved.
bits : 0 - 2 (3 bit)

Enumeration: ENUM

0x0 : SELECTS_FUNCTION_PIO

Selects function PIO2_5.

0x1 : SELECTS_FUNCTION_CT3

Selects function CT32B0_MAT0.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)

Enumeration: ENUM

0x0 : INACTIVE_NO_PULL_DO

Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN_RESISTOR_E

Pull-down resistor enabled.

0x2 : PULL_UP_RESISTOR_ENA

Pull-up resistor enabled.

0x3 : REPEATER_MODE_

Repeater mode.

End of enumeration elements list.

HYS : Hysteresis.
bits : 5 - 10 (6 bit)

Enumeration: ENUM

0 : DISABLE_

Disable.

1 : ENABLE_

Enable.

End of enumeration elements list.

RESERVED : Reserved
bits : 6 - 15 (10 bit)

RESERVED : Reserved
bits : 6 - 15 (10 bit)

OD : Selects pseudo open-drain mode.
bits : 10 - 20 (11 bit)

Enumeration: ENUM

0 : STANDARD_GPIO_OUTPUT

Standard GPIO output

1 : OPEN_DRAIN_OUTPUT

Open-drain output

End of enumeration elements list.


PIO3_5

I/O configuration for pin PIO3_5/ CT16B1_CAP1/TXD
address_offset : 0x48 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO3_5 PIO3_5 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE HYS RESERVED RESERVED OD

FUNC : Selects pin function. All other values are reserved.
bits : 0 - 2 (3 bit)

Enumeration: ENUM

0x0 : SELECTS_FUNCTION_PIO

Selects function PIO3_5.

0x1 : SELECTS_FUNCTION_CT1

Selects function CT16B1_CAP1.

0x2 : SELECTS_FUNCTION_TXD

Selects function TXD.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)

Enumeration: ENUM

0x0 : INACTIVE_NO_PULL_DO

Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN_RESISTOR_E

Pull-down resistor enabled.

0x2 : PULL_UP_RESISTOR_ENA

Pull-up resistor enabled.

0x3 : REPEATER_MODE_

Repeater mode.

End of enumeration elements list.

HYS : Hysteresis.
bits : 5 - 10 (6 bit)

Enumeration: ENUM

0 : DISABLE_

Disable.

1 : ENABLE_

Enable.

End of enumeration elements list.

RESERVED : Reserved
bits : 6 - 15 (10 bit)

RESERVED : Reserved
bits : 6 - 15 (10 bit)

OD : Selects pseudo open-drain mode.
bits : 10 - 20 (11 bit)

Enumeration: ENUM

0 : STANDARD_GPIO_OUTPUT

Standard GPIO output

1 : OPEN_DRAIN_OUTPUT

Open-drain output

End of enumeration elements list.


PIO0_6

I/O configuration for pin PIO0_6/SCK0
address_offset : 0x4C Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO0_6 PIO0_6 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE HYS RESERVED RESERVED OD

FUNC : Selects pin function. All other values are reserved.
bits : 0 - 2 (3 bit)

Enumeration: ENUM

0x0 : SELECTS_FUNCTION_PIO

Selects function PIO0_6.

0x1 : RESERVED_

Reserved.

0x2 : SELECTS_FUNCTION_SCK

Selects function SCK0 (only if pin PIO0_6/SCK0 selected in Table 147).

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)

Enumeration: ENUM

0x0 : INACTIVE_NO_PULL_DO

Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN_RESISTOR_E

Pull-down resistor enabled.

0x2 : PULL_UP_RESISTOR_ENA

Pull-up resistor enabled.

0x3 : REPEATER_MODE_

Repeater mode.

End of enumeration elements list.

HYS : Hysteresis.
bits : 5 - 10 (6 bit)

Enumeration: ENUM

0 : DISABLE_

Disable.

1 : ENABLE_

Enable.

End of enumeration elements list.

RESERVED : Reserved
bits : 6 - 15 (10 bit)

RESERVED : Reserved
bits : 6 - 15 (10 bit)

OD : Selects pseudo open-drain mode.
bits : 10 - 20 (11 bit)

Enumeration: ENUM

0 : STANDARD_GPIO_OUTPUT

Standard GPIO output

1 : OPEN_DRAIN_OUTPUT

Open-drain output

End of enumeration elements list.


PIO0_7

I/O configuration for pin PIO0_7/CTS
address_offset : 0x50 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO0_7 PIO0_7 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE HYS RESERVED RESERVED OD

FUNC : Selects pin function. All other values are reserved.
bits : 0 - 2 (3 bit)

Enumeration: ENUM

0x0 : SELECTS_FUNCTION_PIO

Selects function PIO0_7.

0x1 : SELECT_FUNCTION_CTS_

Select function CTS.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)

Enumeration: ENUM

0x0 : INACTIVE_NO_PULL_DO

Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN_RESISTOR_E

Pull-down resistor enabled.

0x2 : PULL_UP_RESISTOR_ENA

Pull-up resistor enabled.

0x3 : REPEATER_MODE_

Repeater mode.

End of enumeration elements list.

HYS : Hysteresis.
bits : 5 - 10 (6 bit)

Enumeration: ENUM

0 : DISABLE_

Disable.

1 : ENABLE_

Enable.

End of enumeration elements list.

RESERVED : Reserved
bits : 6 - 15 (10 bit)

RESERVED : Reserved
bits : 6 - 15 (10 bit)

OD : Selects pseudo open-drain mode.
bits : 10 - 20 (11 bit)

Enumeration: ENUM

0 : STANDARD_GPIO_OUTPUT

Standard GPIO output

1 : OPEN_DRAIN_OUTPUT

Open-drain output

End of enumeration elements list.


PIO2_9

I/O configuration for pin PIO2_9/ CT32B0_CAP0
address_offset : 0x54 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO2_9 PIO2_9 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE HYS RESERVED RESERVED OD

FUNC : Selects pin function. All other values are reserved.
bits : 0 - 2 (3 bit)

Enumeration: ENUM

0x0 : SELECTS_FUNCTION_PIO

Selects function PIO2_9.

0x1 : SELECTS_FUNCTION_CT3

Selects function CT32B0_CAP0.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)

Enumeration: ENUM

0x0 : INACTIVE_NO_PULL_DO

Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN_RESISTOR_E

Pull-down resistor enabled.

0x2 : PULL_UP_RESISTOR_ENA

Pull-up resistor enabled.

0x3 : REPEATER_MODE_

Repeater mode.

End of enumeration elements list.

HYS : Hysteresis.
bits : 5 - 10 (6 bit)

Enumeration: ENUM

0 : DISABLE_

Disable.

1 : ENABLE_

Enable.

End of enumeration elements list.

RESERVED : Reserved
bits : 6 - 15 (10 bit)

RESERVED : Reserved
bits : 6 - 15 (10 bit)

OD : Selects pseudo open-drain mode.
bits : 10 - 20 (11 bit)

Enumeration: ENUM

0 : STANDARD_GPIO_OUTPUT

Standard GPIO output

1 : OPEN_DRAIN_OUTPUT

Open-drain output

End of enumeration elements list.


PIO2_10

I/O configuration for pin PIO2_10
address_offset : 0x58 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO2_10 PIO2_10 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE HYS RESERVED RESERVED OD

FUNC : Selects pin function. All other values are reserved.
bits : 0 - 2 (3 bit)

Enumeration: ENUM

0x0 : SELECTS_FUNCTION_PIO

Selects function PIO2_10.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)

Enumeration: ENUM

0x0 : INACTIVE_NO_PULL_DO

Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN_RESISTOR_E

Pull-down resistor enabled.

0x2 : PULL_UP_RESISTOR_ENA

Pull-up resistor enabled.

0x3 : REPEATER_MODE_

Repeater mode.

End of enumeration elements list.

HYS : Hysteresis.
bits : 5 - 10 (6 bit)

Enumeration: ENUM

0 : DISABLE_

Disable.

1 : ENABLE_

Enable.

End of enumeration elements list.

RESERVED : Reserved
bits : 6 - 15 (10 bit)

RESERVED : Reserved
bits : 6 - 15 (10 bit)

OD : Selects pseudo open-drain mode.
bits : 10 - 20 (11 bit)

Enumeration: ENUM

0 : STANDARD_GPIO_OUTPUT

Standard GPIO output

1 : OPEN_DRAIN_OUTPUT

Open-drain output

End of enumeration elements list.


PIO2_2

I/O configuration for pin PIO2_2/DCD/MISO1
address_offset : 0x5C Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO2_2 PIO2_2 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE HYS RESERVED RESERVED OD

FUNC : Selects pin function. All other values are reserved.
bits : 0 - 2 (3 bit)

Enumeration: ENUM

0x0 : SELECTS_FUNCTION_PIO

Selects function PIO2_2.

0x1 : SELECT_FUNCTION_DCD_

Select function DCD.

0x2 : SELECT_FUNCTION_MISO

Select function MISO1.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)

Enumeration: ENUM

0x0 : INACTIVE_NO_PULL_DO

Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN_RESISTOR_E

Pull-down resistor enabled.

0x2 : PULL_UP_RESISTOR_ENA

Pull-up resistor enabled.

0x3 : REPEATER_MODE_

Repeater mode.

End of enumeration elements list.

HYS : Hysteresis.
bits : 5 - 10 (6 bit)

Enumeration: ENUM

0 : DISABLE_

Disable.

1 : ENABLE_

Enable.

End of enumeration elements list.

RESERVED : Reserved
bits : 6 - 15 (10 bit)

RESERVED : Reserved
bits : 6 - 15 (10 bit)

OD : Selects pseudo open-drain mode.
bits : 10 - 20 (11 bit)

Enumeration: ENUM

0 : STANDARD_GPIO_OUTPUT

Standard GPIO output

1 : OPEN_DRAIN_OUTPUT

Open-drain output

End of enumeration elements list.


PIO0_8

I/O configuration for pin PIO0_8/MISO0/CT16B0_MAT0
address_offset : 0x60 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO0_8 PIO0_8 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE HYS RESERVED RESERVED OD

FUNC : Selects pin function. All other values are reserved.
bits : 0 - 2 (3 bit)

Enumeration: ENUM

0x0 : SELECTS_FUNCTION_PIO

Selects function PIO0_8.

0x1 : SELECTS_FUNCTION_MIS

Selects function MISO0.

0x2 : SELECTS_FUNCTION_CT1

Selects function CT16B0_MAT0.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)

Enumeration: ENUM

0x0 : INACTIVE_NO_PULL_DO

Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN_RESISTOR_E

Pull-down resistor enabled.

0x2 : PULL_UP_RESISTOR_ENA

Pull-up resistor enabled.

0x3 : REPEATER_MODE_

Repeater mode.

End of enumeration elements list.

HYS : Hysteresis.
bits : 5 - 10 (6 bit)

Enumeration: ENUM

0 : DISABLE_

Disable.

1 : ENABLE_

Enable.

End of enumeration elements list.

RESERVED : Reserved
bits : 6 - 15 (10 bit)

RESERVED : Reserved
bits : 6 - 15 (10 bit)

OD : Selects pseudo open-drain mode.
bits : 10 - 20 (11 bit)

Enumeration: ENUM

0 : STANDARD_GPIO_OUTPUT

Standard GPIO output

1 : OPEN_DRAIN_OUTPUT

Open-drain output

End of enumeration elements list.


PIO0_9

I/O configuration for pin PIO0_9/MOSI0/CT16B0_MAT1
address_offset : 0x64 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO0_9 PIO0_9 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE HYS RESERVED RESERVED OD

FUNC : Selects pin function. All other values are reserved.
bits : 0 - 2 (3 bit)

Enumeration: ENUM

0x0 : SELECTS_FUNCTION_PIO

Selects function PIO0_9.

0x1 : SELECTS_FUNCTION_MOS

Selects function MOSI0.

0x2 : SELECTS_FUNCTION_CT1

Selects function CT16B0_MAT1.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)

Enumeration: ENUM

0x0 : INACTIVE_NO_PULL_DO

Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN_RESISTOR_E

Pull-down resistor enabled.

0x2 : PULL_UP_RESISTOR_ENA

Pull-up resistor enabled.

0x3 : REPEATER_MODE_

Repeater mode.

End of enumeration elements list.

HYS : Hysteresis.
bits : 5 - 10 (6 bit)

Enumeration: ENUM

0 : DISABLE_

Disable.

1 : ENABLE_

Enable.

End of enumeration elements list.

RESERVED : Reserved
bits : 6 - 15 (10 bit)

RESERVED : Reserved
bits : 6 - 15 (10 bit)

OD : Selects pseudo open-drain mode.
bits : 10 - 20 (11 bit)

Enumeration: ENUM

0 : STANDARD_GPIO_OUTPUT

Standard GPIO output

1 : OPEN_DRAIN_OUTPUT

Open-drain output

End of enumeration elements list.


SWCLK_PIO0_10

I/O configuration for pin SWCLK/PIO0_10/ SCK0/CT16B0_MAT2
address_offset : 0x68 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

SWCLK_PIO0_10 SWCLK_PIO0_10 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE HYS RESERVED RESERVED OD

FUNC : Selects pin function. All other values are reserved.
bits : 0 - 2 (3 bit)

Enumeration: ENUM

0x0 : SELECTS_FUNCTION_SWC

Selects function SWCLK.

0x1 : SELECTS_FUNCTION_PIO

Selects function PIO0_10.

0x2 : SELECTS_FUNCTION_SCK

Selects function SCK0 (only if pin SWCLK/PIO0_10/SCK0/CT16B0_MAT2 selected in Table 147).

0x3 : SELECTS_FUNCTION_CT1

Selects function CT16B0_MAT2.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)

Enumeration: ENUM

0x0 : INACTIVE_NO_PULL_DO

Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN_RESISTOR_E

Pull-down resistor enabled.

0x2 : PULL_UP_RESISTOR_ENA

Pull-up resistor enabled.

0x3 : REPEATER_MODE_

Repeater mode.

End of enumeration elements list.

HYS : Hysteresis.
bits : 5 - 10 (6 bit)

Enumeration: ENUM

0 : DISABLE_

Disable.

1 : ENABLE_

Enable.

End of enumeration elements list.

RESERVED : Reserved
bits : 6 - 15 (10 bit)

RESERVED : Reserved
bits : 6 - 15 (10 bit)

OD : Selects pseudo open-drain mode.
bits : 10 - 20 (11 bit)

Enumeration: ENUM

0 : STANDARD_GPIO_OUTPUT

Standard GPIO output

1 : OPEN_DRAIN_OUTPUT

Open-drain output

End of enumeration elements list.


PIO1_10

I/O configuration for pin PIO1_10/AD6/CT16B1_MAT1/ MISO1
address_offset : 0x6C Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO1_10 PIO1_10 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE HYS RESERVED ADMODE RESERVED RESERVED OD

FUNC : Selects pin function. All other values are reserved.
bits : 0 - 2 (3 bit)

Enumeration: ENUM

0x0 : SELECTS_FUNCTION_PIO

Selects function PIO1_10.

0x1 : SELECTS_FUNCTION_AD6

Selects function AD6.

0x2 : SELECTS_FUNCTION_CT1

Selects function CT16B1_MAT1.

0x3 : SELECTS_FUNCTION_MIS

Selects function MISO1.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)

Enumeration: ENUM

0x0 : INACTIVE_NO_PULL_DO

Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN_RESISTOR_E

Pull-down resistor enabled.

0x2 : PULL_UP_RESISTOR_ENA

Pull-up resistor enabled.

0x3 : REPEATER_MODE_

Repeater mode.

End of enumeration elements list.

HYS : Hysteresis.
bits : 5 - 10 (6 bit)

Enumeration: ENUM

0 : DISABLE_

Disable.

1 : ENABLE_

Enable.

End of enumeration elements list.

RESERVED : Reserved
bits : 6 - 12 (7 bit)

ADMODE : Selects Analog/Digital mode
bits : 7 - 14 (8 bit)

Enumeration: ENUM

0 : ANALOG_INPUT_MODE

Analog input mode

1 : DIGITAL_FUNCTIONAL_M

Digital functional mode

End of enumeration elements list.

RESERVED : Reserved
bits : 8 - 17 (10 bit)

RESERVED : Reserved
bits : 8 - 17 (10 bit)

OD : Selects pseudo open-drain mode.
bits : 10 - 20 (11 bit)

Enumeration: ENUM

0 : STANDARD_GPIO_OUTPUT

Standard GPIO output

1 : OPEN_DRAIN_OUTPUT

Open-drain output

End of enumeration elements list.


PIO2_11

I/O configuration for pin PIO2_11/SCK0/ CT32B0_CAP1
address_offset : 0x70 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO2_11 PIO2_11 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE HYS RESERVED RESERVED OD

FUNC : Selects pin function. All other values are reserved.
bits : 0 - 2 (3 bit)

Enumeration: ENUM

0x0 : SELECTS_FUNCTION_PIO

Selects function PIO2_11.

0x1 : SELECT_FUNCTION_SCK0

Select function SCK0 (only if pin PIO2_11/SCK0 selected in Table 147).

0x2 : SELECT_FUNCTION_CT32

Select function CT32B0_CAP1.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)

Enumeration: ENUM

0x0 : INACTIVE_NO_PULL_DO

Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN_RESISTOR_E

Pull-down resistor enabled.

0x2 : PULL_UP_RESISTOR_ENA

Pull-up resistor enabled.

0x3 : REPEATER_MODE_

Repeater mode.

End of enumeration elements list.

HYS : Hysteresis.
bits : 5 - 10 (6 bit)

Enumeration: ENUM

0 : DISABLE_

Disable.

1 : ENABLE_

Enable.

End of enumeration elements list.

RESERVED : Reserved
bits : 6 - 15 (10 bit)

RESERVED : Reserved
bits : 6 - 15 (10 bit)

OD : Selects pseudo open-drain mode.
bits : 10 - 20 (11 bit)

Enumeration: ENUM

0 : STANDARD_GPIO_OUTPUT

Standard GPIO output

1 : OPEN_DRAIN_OUTPUT

Open-drain output

End of enumeration elements list.


R_PIO0_11

I/O configuration for pin R/PIO0_11/AD0/CT32B0_MAT3
address_offset : 0x74 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

R_PIO0_11 R_PIO0_11 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE HYS RESERVED ADMODE RESERVED RESERVED OD

FUNC : Selects pin function. All other values are reserved.
bits : 0 - 2 (3 bit)

Enumeration: ENUM

0x0 : SELECTS_FUNCTION_R_

Selects function R. This function is reserved. Select one of the alternate functions below.

0x1 : SELECTS_FUNCTION_PIO

Selects function PIO0_11.

0x2 : SELECTS_FUNCTION_AD0

Selects function AD0.

0x3 : SELECTS_FUNCTION_CT3

Selects function CT32B0_MAT3.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)

Enumeration: ENUM

0x0 : INACTIVE_NO_PULL_DO

Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN_RESISTOR_E

Pull-down resistor enabled.

0x2 : PULL_UP_RESISTOR_ENA

Pull-up resistor enabled.

0x3 : REPEATER_MODE_

Repeater mode.

End of enumeration elements list.

HYS : Hysteresis.
bits : 5 - 10 (6 bit)

Enumeration: ENUM

0 : DISABLE_

Disable.

1 : ENABLE_

Enable.

End of enumeration elements list.

RESERVED : Reserved
bits : 6 - 12 (7 bit)

ADMODE : Selects Analog/Digital mode
bits : 7 - 14 (8 bit)

Enumeration: ENUM

0 : ANALOG_INPUT_MODE

Analog input mode

1 : DIGITAL_FUNCTIONAL_M

Digital functional mode

End of enumeration elements list.

RESERVED : Reserved
bits : 8 - 17 (10 bit)

RESERVED : Reserved
bits : 8 - 17 (10 bit)

OD : Selects pseudo open-drain mode.
bits : 10 - 20 (11 bit)

Enumeration: ENUM

0 : STANDARD_GPIO_OUTPUT

Standard GPIO output

1 : OPEN_DRAIN_OUTPUT

Open-drain output

End of enumeration elements list.


R_PIO1_0

I/O configuration for pin R/PIO1_0/AD1/CT32B1_CAP0
address_offset : 0x78 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

R_PIO1_0 R_PIO1_0 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE HYS RESERVED ADMODE RESERVED RESERVED OD

FUNC : Selects pin function. All other values are reserved.
bits : 0 - 2 (3 bit)

Enumeration: ENUM

0x0 : SELECTS_FUNCTION_R_

Selects function R. This function is reserved. Select one of the alternate functions below.

0x1 : SELECTS_FUNCTION_PIO

Selects function PIO1_0.

0x2 : SELECTS_FUNCTION_AD1

Selects function AD1.

0x3 : SELECTS_FUNCTION_CT3

Selects function CT32B1_CAP0.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)

Enumeration: ENUM

0x0 : INACTIVE_NO_PULL_DO

Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN_RESISTOR_E

Pull-down resistor enabled.

0x2 : PULL_UP_RESISTOR_ENA

Pull-up resistor enabled.

0x3 : REPEATER_MODE_

Repeater mode.

End of enumeration elements list.

HYS : Hysteresis.
bits : 5 - 10 (6 bit)

Enumeration: ENUM

0 : DISABLE_

Disable.

1 : ENABLE_

Enable.

End of enumeration elements list.

RESERVED : Reserved
bits : 6 - 12 (7 bit)

ADMODE : Selects Analog/Digital mode
bits : 7 - 14 (8 bit)

Enumeration: ENUM

0 : ANALOG_INPUT_MODE

Analog input mode

1 : DIGITAL_FUNCTIONAL_M

Digital functional mode

End of enumeration elements list.

RESERVED : Reserved
bits : 8 - 17 (10 bit)

RESERVED : Reserved
bits : 8 - 17 (10 bit)

OD : Selects pseudo open-drain mode.
bits : 10 - 20 (11 bit)

Enumeration: ENUM

0 : STANDARD_GPIO_OUTPUT

Standard GPIO output

1 : OPEN_DRAIN_OUTPUT

Open-drain output

End of enumeration elements list.


R_PIO1_1

I/O configuration for pin R/PIO1_1/AD2/CT32B1_MAT0
address_offset : 0x7C Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

R_PIO1_1 R_PIO1_1 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE HYS RESERVED ADMODE RESERVED RESERVED OD

FUNC : Selects pin function. All other values are reserved.
bits : 0 - 2 (3 bit)

Enumeration: ENUM

0x0 : SELECTS_FUNCTION_R_

Selects function R. This function is reserved. Select one of the alternate functions below.

0x1 : SELECTS_FUNCTION_PIO

Selects function PIO1_1.

0x2 : SELECTS_FUNCTION_AD2

Selects function AD2.

0x3 : SELECTS_FUNCTION_CT3

Selects function CT32B1_MAT0.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)

Enumeration: ENUM

0x0 : INACTIVE_NO_PULL_DO

Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN_RESISTOR_E

Pull-down resistor enabled.

0x2 : PULL_UP_RESISTOR_ENA

Pull-up resistor enabled.

0x3 : REPEATER_MODE_

Repeater mode.

End of enumeration elements list.

HYS : Hysteresis.
bits : 5 - 10 (6 bit)

Enumeration: ENUM

0 : DISABLE_

Disable.

1 : ENABLE_

Enable.

End of enumeration elements list.

RESERVED : Reserved
bits : 6 - 12 (7 bit)

ADMODE : Selects Analog/Digital mode
bits : 7 - 14 (8 bit)

Enumeration: ENUM

0 : ANALOG_INPUT_MODE

Analog input mode

1 : DIGITAL_FUNCTIONAL_M

Digital functional mode

End of enumeration elements list.

RESERVED : Reserved
bits : 8 - 17 (10 bit)

RESERVED : Reserved
bits : 8 - 17 (10 bit)

OD : Selects pseudo open-drain mode.
bits : 10 - 20 (11 bit)

Enumeration: ENUM

0 : STANDARD_GPIO_OUTPUT

Standard GPIO output

1 : OPEN_DRAIN_OUTPUT

Open-drain output

End of enumeration elements list.


PIO2_0

I/O configuration for pin PIO2_0/DTR/SSEL1
address_offset : 0x8 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO2_0 PIO2_0 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE HYS RESERVED RESERVED OD

FUNC : Selects pin function. All other values are reserved.
bits : 0 - 2 (3 bit)

Enumeration: ENUM

0x0 : SELECTS_FUNCTION_PIO

Selects function PIO2_0.

0x1 : SELECT_FUNCTION_DTR_

Select function DTR.

0x2 : SELECT_FUNCTION_SSEL

Select function SSEL1.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)

Enumeration: ENUM

0x0 : INACTIVE_NO_PULL_DO

Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN_RESISTOR_E

Pull-down resistor enabled.

0x2 : PULL_UP_RESISTOR_ENA

Pull-up resistor enabled.

0x3 : REPEATER_MODE_

Repeater mode.

End of enumeration elements list.

HYS : Hysteresis.
bits : 5 - 10 (6 bit)

Enumeration: ENUM

0 : DISABLE_

Disable.

1 : ENABLE_

Enable.

End of enumeration elements list.

RESERVED : Reserved
bits : 6 - 15 (10 bit)

RESERVED : Reserved
bits : 6 - 15 (10 bit)

OD : Selects pseudo open-drain mode.
bits : 10 - 20 (11 bit)

Enumeration: ENUM

0 : STANDARD_GPIO_OUTPUT

Standard GPIO output

1 : OPEN_DRAIN_OUTPUT

Open-drain output

End of enumeration elements list.


R_PIO1_2

I/O configuration for pin R/PIO1_2/AD3/CT32B1_MAT1
address_offset : 0x80 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

R_PIO1_2 R_PIO1_2 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE HYS RESERVED ADMODE RESERVED RESERVED OD

FUNC : Selects pin function. All other values are reserved.
bits : 0 - 2 (3 bit)

Enumeration: ENUM

0x0 : SELECTS_FUNCTION_R_

Selects function R. This function is reserved. Select one of the alternate functions below.

0x1 : SELECTS_FUNCTION_PIO

Selects function PIO1_2.

0x2 : SELECTS_FUNCTION_AD3

Selects function AD3.

0x3 : SELECTS_FUNCTION_CT3

Selects function CT32B1_MAT1.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)

Enumeration: ENUM

0x0 : INACTIVE_NO_PULL_DO

Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN_RESISTOR_E

Pull-down resistor enabled.

0x2 : PULL_UP_RESISTOR_ENA

Pull-up resistor enabled.

0x3 : REPEATER_MODE_

Repeater mode.

End of enumeration elements list.

HYS : Hysteresis.
bits : 5 - 10 (6 bit)

Enumeration: ENUM

0 : DISABLE_

Disable.

1 : ENABLE_

Enable.

End of enumeration elements list.

RESERVED : Reserved
bits : 6 - 12 (7 bit)

ADMODE : Selects Analog/Digital mode
bits : 7 - 14 (8 bit)

Enumeration: ENUM

0 : ANALOG_INPUT_MODE

Analog input mode

1 : DIGITAL_FUNCTIONAL_M

Digital functional mode

End of enumeration elements list.

RESERVED : Reserved
bits : 8 - 17 (10 bit)

RESERVED : Reserved
bits : 8 - 17 (10 bit)

OD : Selects pseudo open-drain mode.
bits : 10 - 20 (11 bit)

Enumeration: ENUM

0 : STANDARD_GPIO_OUTPUT

Standard GPIO output

1 : OPEN_DRAIN_OUTPUT

Open-drain output

End of enumeration elements list.


PIO3_0

I/O configuration for pin PIO3_0/DTR/CT16B0_MAT0/TXD
address_offset : 0x84 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO3_0 PIO3_0 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE HYS RESERVED RESERVED OD

FUNC : Selects pin function. All other values are reserved.
bits : 0 - 2 (3 bit)

Enumeration: ENUM

0x0 : SELECTS_FUNCTION_PIO

Selects function PIO3_0.

0x1 : SELECTS_FUNCTION_DTR

Selects function DTR.

0x2 : SELECTS_FUNCTION_CT1

Selects function CT16B0_MAT0.

0x3 : SELECTS_FUNCTION_TXD

Selects function TXD.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)

Enumeration: ENUM

0x0 : INACTIVE_NO_PULL_DO

Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN_RESISTOR_E

Pull-down resistor enabled.

0x2 : PULL_UP_RESISTOR_ENA

Pull-up resistor enabled.

0x3 : REPEATER_MODE_

Repeater mode.

End of enumeration elements list.

HYS : Hysteresis.
bits : 5 - 10 (6 bit)

Enumeration: ENUM

0 : DISABLE_

Disable.

1 : ENABLE_

Enable.

End of enumeration elements list.

RESERVED : Reserved
bits : 6 - 15 (10 bit)

RESERVED : Reserved
bits : 6 - 15 (10 bit)

OD : Selects pseudo open-drain mode.
bits : 10 - 20 (11 bit)

Enumeration: ENUM

0 : STANDARD_GPIO_OUTPUT

Standard GPIO output

1 : OPEN_DRAIN_OUTPUT

Open-drain output

End of enumeration elements list.


PIO3_1

I/O configuration for pin PIO3_1/DSR/CT16B0_MAT1/RXD
address_offset : 0x88 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO3_1 PIO3_1 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE HYS RESERVED RESERVED OD

FUNC : Selects pin function. All other values are reserved.
bits : 0 - 2 (3 bit)

Enumeration: ENUM

0x0 : SELECTS_FUNCTION_PIO

Selects function PIO3_1.

0x1 : SELECTS_FUNCTION_DSR

Selects function DSR.

0x2 : SELECTS_FUNCTION_CT1

Selects function CT16B0_MAT1.

0x3 : SELECTS_FUNCTION_RXD

Selects function RXD.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)

Enumeration: ENUM

0x0 : INACTIVE_NO_PULL_DO

Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN_RESISTOR_E

Pull-down resistor enabled.

0x2 : PULL_UP_RESISTOR_ENA

Pull-up resistor enabled.

0x3 : REPEATER_MODE_

Repeater mode.

End of enumeration elements list.

HYS : Hysteresis.
bits : 5 - 10 (6 bit)

Enumeration: ENUM

0 : DISABLE_

Disable.

1 : ENABLE_

Enable.

End of enumeration elements list.

RESERVED : Reserved
bits : 6 - 15 (10 bit)

RESERVED : Reserved
bits : 6 - 15 (10 bit)

OD : Selects pseudo open-drain mode.
bits : 10 - 20 (11 bit)

Enumeration: ENUM

0 : STANDARD_GPIO_OUTPUT

Standard GPIO output

1 : OPEN_DRAIN_OUTPUT

Open-drain output

End of enumeration elements list.


PIO2_3

I/O configuration for pin PIO2_3/RI/MOSI1
address_offset : 0x8C Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO2_3 PIO2_3 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE HYS RESERVED RESERVED OD

FUNC : Selects pin function. All other values are reserved.
bits : 0 - 2 (3 bit)

Enumeration: ENUM

0x0 : SELECTS_FUNCTION_PIO

Selects function PIO2_3.

0x1 : SELECTS_FUNCTION_RI_

Selects function RI.

0x2 : SELECTS_FUNCTION_MOS

Selects function MOSI1.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)

Enumeration: ENUM

0x0 : INACTIVE_NO_PULL_DO

Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN_RESISTOR_E

Pull-down resistor enabled.

0x2 : PULL_UP_RESISTOR_ENA

Pull-up resistor enabled.

0x3 : REPEATER_MODE_

Repeater mode.

End of enumeration elements list.

HYS : Hysteresis.
bits : 5 - 10 (6 bit)

Enumeration: ENUM

0 : DISABLE_

Disable.

1 : ENABLE_

Enable.

End of enumeration elements list.

RESERVED : Reserved
bits : 6 - 15 (10 bit)

RESERVED : Reserved
bits : 6 - 15 (10 bit)

OD : Selects pseudo open-drain mode.
bits : 10 - 20 (11 bit)

Enumeration: ENUM

0 : STANDARD_GPIO_OUTPUT

Standard GPIO output

1 : OPEN_DRAIN_OUTPUT

Open-drain output

End of enumeration elements list.


SWDIO_PIO1_3

I/O configuration for pin SWDIO/PIO1_3/AD4/CT32B1_MAT2
address_offset : 0x90 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

SWDIO_PIO1_3 SWDIO_PIO1_3 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE HYS RESERVED ADMODE RESERVED RESERVED OD

FUNC : Selects pin function. All other values are reserved.
bits : 0 - 2 (3 bit)

Enumeration: ENUM

0x0 : SELECTS_FUNCTION_SWD

Selects function SWDIO.

0x1 : SELECTS_FUNCTION_PIO

Selects function PIO1_3.

0x2 : SELECTS_FUNCTION_AD4

Selects function AD4.

0x3 : SELECTS_FUNCTION_CT3

Selects function CT32B1_MAT2.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)

Enumeration: ENUM

0x0 : INACTIVE_NO_PULL_DO

Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN_RESISTOR_E

Pull-down resistor enabled.

0x2 : PULL_UP_RESISTOR_ENA

Pull-up resistor enabled.

0x3 : REPEATER_MODE_

Repeater mode.

End of enumeration elements list.

HYS : Hysteresis.
bits : 5 - 10 (6 bit)

Enumeration: ENUM

0 : DISABLE_

Disable.

1 : ENABLE_

Enable.

End of enumeration elements list.

RESERVED : Reserved
bits : 6 - 12 (7 bit)

ADMODE : Selects Analog/Digital mode
bits : 7 - 14 (8 bit)

Enumeration: ENUM

0 : ANALOG_INPUT_MODE

Analog input mode

1 : DIGITAL_FUNCTIONAL_M

Digital functional mode

End of enumeration elements list.

RESERVED : Reserved
bits : 8 - 17 (10 bit)

RESERVED : Reserved
bits : 8 - 17 (10 bit)

OD : Selects pseudo open-drain mode.
bits : 10 - 20 (11 bit)

Enumeration: ENUM

0 : STANDARD_GPIO_OUTPUT

Standard GPIO output

1 : OPEN_DRAIN_OUTPUT

Open-drain output

End of enumeration elements list.


PIO1_4

I/O configuration for pin PIO1_4/AD5/CT32B1_MAT3
address_offset : 0x94 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO1_4 PIO1_4 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE HYS RESERVED ADMODE RESERVED RESERVED OD

FUNC : Selects pin function. This pin functions as WAKEUP pin if the LPC111x/LPC11Cxx is in Deep power-down mode regardless of the value of FUNC. All other values are reserved.
bits : 0 - 2 (3 bit)

Enumeration: ENUM

0x0 : SELECTS_FUNCTION_PIO

Selects function PIO1_4.

0x1 : SELECTS_FUNCTION_AD5

Selects function AD5.

0x2 : SELECTS_FUNCTION_CT3

Selects function CT32B1_MAT3.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)

Enumeration: ENUM

0x0 : INACTIVE_NO_PULL_DO

Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN_RESISTOR_E

Pull-down resistor enabled.

0x2 : PULL_UP_RESISTOR_ENA

Pull-up resistor enabled.

0x3 : REPEATER_MODE_

Repeater mode.

End of enumeration elements list.

HYS : Hysteresis.
bits : 5 - 10 (6 bit)

Enumeration: ENUM

0 : DISABLE_

Disable.

1 : ENABLE_

Enable.

End of enumeration elements list.

RESERVED : Reserved
bits : 6 - 12 (7 bit)

ADMODE : Selects Analog/Digital mode
bits : 7 - 14 (8 bit)

Enumeration: ENUM

0 : ANALOG_INPUT_MODE

Analog input mode

1 : DIGITAL_FUNCTIONAL_M

Digital functional mode

End of enumeration elements list.

RESERVED : Reserved
bits : 8 - 17 (10 bit)

RESERVED : Reserved
bits : 8 - 17 (10 bit)

OD : Selects pseudo open-drain mode.
bits : 10 - 20 (11 bit)

Enumeration: ENUM

0 : STANDARD_GPIO_OUTPUT

Standard GPIO output

1 : OPEN_DRAIN_OUTPUT

Open-drain output

End of enumeration elements list.


PIO1_11

I/O configuration for pin PIO1_11/AD7/CT32B1_CAP1
address_offset : 0x98 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO1_11 PIO1_11 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE HYS RESERVED ADMODE RESERVED RESERVED OD

FUNC : Selects pin function. All other values are reserved.
bits : 0 - 2 (3 bit)

Enumeration: ENUM

0x0 : SELECTS_FUNCTION_PIO

Selects function PIO1_11.

0x1 : SELECTS_FUNCTION_AD7

Selects function AD7.

0x2 : SELECTS_FUNCTION_CT3

Selects function CT32B1_CAP1.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)

Enumeration: ENUM

0x0 : INACTIVE_NO_PULL_DO

Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN_RESISTOR_E

Pull-down resistor enabled.

0x2 : PULL_UP_RESISTOR_ENA

Pull-up resistor enabled.

0x3 : REPEATER_MODE_

Repeater mode.

End of enumeration elements list.

HYS : Hysteresis.
bits : 5 - 10 (6 bit)

Enumeration: ENUM

0 : DISABLE_

Disable.

1 : ENABLE_

Enable.

End of enumeration elements list.

RESERVED : Reserved
bits : 6 - 12 (7 bit)

ADMODE : Selects Analog/Digital mode
bits : 7 - 14 (8 bit)

Enumeration: ENUM

0 : ANALOG_INPUT_MODE

Analog input mode

1 : DIGITAL_FUNCTIONAL_M

Digital functional mode

End of enumeration elements list.

RESERVED : Reserved
bits : 8 - 17 (10 bit)

RESERVED : Reserved
bits : 8 - 17 (10 bit)

OD : Selects pseudo open-drain mode.
bits : 10 - 20 (11 bit)

Enumeration: ENUM

0 : STANDARD_GPIO_OUTPUT

Standard GPIO output

1 : OPEN_DRAIN_OUTPUT

Open-drain output

End of enumeration elements list.


PIO3_2

I/O configuration for pin PIO3_2/DCD/ CT16B0_MAT2/SCK1
address_offset : 0x9C Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO3_2 PIO3_2 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE HYS RESERVED RESERVED OD

FUNC : Selects pin function. All other values are reserved.
bits : 0 - 2 (3 bit)

Enumeration: ENUM

0x0 : SELECTS_FUNCTION_PIO

Selects function PIO3_2.

0x1 : SELECTS_FUNCTION_DCD

Selects function DCD.

0x2 : SELECTS_FUNCTION_CT1

Selects function CT16B0_MAT2.

0x3 : SELECTS_FUNCTION_SCK

Selects function SCK1.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)

Enumeration: ENUM

0x0 : INACTIVE_NO_PULL_DO

Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN_RESISTOR_E

Pull-down resistor enabled.

0x2 : PULL_UP_RESISTOR_ENA

Pull-up resistor enabled.

0x3 : REPEATER_MODE_

Repeater mode.

End of enumeration elements list.

HYS : Hysteresis.
bits : 5 - 10 (6 bit)

Enumeration: ENUM

0 : DISABLE_

Disable.

1 : ENABLE_

Enable.

End of enumeration elements list.

RESERVED : Reserved
bits : 6 - 15 (10 bit)

RESERVED : Reserved
bits : 6 - 15 (10 bit)

OD : Selects pseudo open-drain mode.
bits : 10 - 20 (11 bit)

Enumeration: ENUM

0 : STANDARD_GPIO_OUTPUT

Standard GPIO output

1 : OPEN_DRAIN_OUTPUT

Open-drain output

End of enumeration elements list.


PIO1_5

I/O configuration for pin PIO1_5/RTS/CT32B0_CAP0
address_offset : 0xA0 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO1_5 PIO1_5 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE HYS RESERVED RESERVED OD

FUNC : Selects pin function. All other values are reserved.
bits : 0 - 2 (3 bit)

Enumeration: ENUM

0x0 : SELECTS_FUNCTION_PIO

Selects function PIO1_5.

0x1 : SELECTS_FUNCTION_RTS

Selects function RTS.

0x2 : SELECTS_FUNCTION_CT3

Selects function CT32B0_CAP0.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)

Enumeration: ENUM

0x0 : INACTIVE_NO_PULL_DO

Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN_RESISTOR_E

Pull-down resistor enabled.

0x2 : PULL_UP_RESISTOR_ENA

Pull-up resistor enabled.

0x3 : REPEATER_MODE_

Repeater mode.

End of enumeration elements list.

HYS : Hysteresis.
bits : 5 - 10 (6 bit)

Enumeration: ENUM

0 : DISABLE_

Disable.

1 : ENABLE_

Enable.

End of enumeration elements list.

RESERVED : Reserved
bits : 6 - 15 (10 bit)

RESERVED : Reserved
bits : 6 - 15 (10 bit)

OD : Selects pseudo open-drain mode.
bits : 10 - 20 (11 bit)

Enumeration: ENUM

0 : STANDARD_GPIO_OUTPUT

Standard GPIO output

1 : OPEN_DRAIN_OUTPUT

Open-drain output

End of enumeration elements list.


PIO1_6

I/O configuration for pin PIO1_6/RXD/CT32B0_MAT0
address_offset : 0xA4 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO1_6 PIO1_6 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE HYS RESERVED RESERVED OD

FUNC : Selects pin function. All other values are reserved.
bits : 0 - 2 (3 bit)

Enumeration: ENUM

0x0 : SELECTS_FUNCTION_PIO

Selects function PIO1_6.

0x1 : SELECTS_FUNCTION_RXD

Selects function RXD.

0x2 : SELECTS_FUNCTION_CT3

Selects function CT32B0_MAT0.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)

Enumeration: ENUM

0x0 : INACTIVE_NO_PULL_DO

Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN_RESISTOR_E

Pull-down resistor enabled.

0x2 : PULL_UP_RESISTOR_ENA

Pull-up resistor enabled.

0x3 : REPEATER_MODE_

Repeater mode.

End of enumeration elements list.

HYS : Hysteresis.
bits : 5 - 10 (6 bit)

Enumeration: ENUM

0 : DISABLE_

Disable.

1 : ENABLE_

Enable.

End of enumeration elements list.

RESERVED : Reserved
bits : 6 - 15 (10 bit)

RESERVED : Reserved
bits : 6 - 15 (10 bit)

OD : Selects pseudo open-drain mode.
bits : 10 - 20 (11 bit)

Enumeration: ENUM

0 : STANDARD_GPIO_OUTPUT

Standard GPIO output

1 : OPEN_DRAIN_OUTPUT

Open-drain output

End of enumeration elements list.


PIO1_7

I/O configuration for pin PIO1_7/TXD/CT32B0_MAT1
address_offset : 0xA8 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO1_7 PIO1_7 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE HYS RESERVED RESERVED OD

FUNC : Selects pin function. All other values are reserved.
bits : 0 - 2 (3 bit)

Enumeration: ENUM

0x0 : SELECTS_FUNCTION_PIO

Selects function PIO1_7.

0x1 : SELECTS_FUNCTION_TXD

Selects function TXD.

0x2 : SELECTS_FUNCTION_CT3

Selects function CT32B0_MAT1.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)

Enumeration: ENUM

0x0 : INACTIVE_NO_PULL_DO

Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN_RESISTOR_E

Pull-down resistor enabled.

0x2 : PULL_UP_RESISTOR_ENA

Pull-up resistor enabled.

0x3 : REPEATER_MODE_

Repeater mode.

End of enumeration elements list.

HYS : Hysteresis.
bits : 5 - 10 (6 bit)

Enumeration: ENUM

0 : DISABLE_

Disable.

1 : ENABLE_

Enable.

End of enumeration elements list.

RESERVED : Reserved
bits : 6 - 15 (10 bit)

RESERVED : Reserved
bits : 6 - 15 (10 bit)

OD : Selects pseudo open-drain mode.
bits : 10 - 20 (11 bit)

Enumeration: ENUM

0 : STANDARD_GPIO_OUTPUT

Standard GPIO output

1 : OPEN_DRAIN_OUTPUT

Open-drain output

End of enumeration elements list.


PIO3_3

I/O configuration for pin PIO3_3/RI/ CT16B0_CAP0
address_offset : 0xAC Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO3_3 PIO3_3 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE HYS RESERVED RESERVED OD

FUNC : Selects pin function. All other values are reserved.
bits : 0 - 2 (3 bit)

Enumeration: ENUM

0x0 : SELECTS_FUNCTION_PIO

Selects function PIO3_3.

0x1 : SELECTS_FUNCTION_RI_

Selects function RI.

0x2 : SELECTS_FUNCTION_CT1

Selects function CT16B0_CAP0.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)

Enumeration: ENUM

0x0 : INACTIVE_NO_PULL_DO

Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN_RESISTOR_E

Pull-down resistor enabled.

0x2 : PULL_UP_RESISTOR_ENA

Pull-up resistor enabled.

0x3 : REPEATER_MODE_

Repeater mode.

End of enumeration elements list.

HYS : Hysteresis.
bits : 5 - 10 (6 bit)

Enumeration: ENUM

0 : DISABLE_

Disable.

1 : ENABLE_

Enable.

End of enumeration elements list.

RESERVED : Reserved
bits : 6 - 15 (10 bit)

RESERVED : Reserved
bits : 6 - 15 (10 bit)

OD : Selects pseudo open-drain mode.
bits : 10 - 20 (11 bit)

Enumeration: ENUM

0 : STANDARD_GPIO_OUTPUT

Standard GPIO output

1 : OPEN_DRAIN_OUTPUT

Open-drain output

End of enumeration elements list.


SCK0_LOC

SCK0 pin location select register
address_offset : 0xB0 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

SCK0_LOC SCK0_LOC read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SCKLOC RESERVED

SCKLOC : Selects pin location for SCK0 function.
bits : 0 - 1 (2 bit)

Enumeration: ENUM

0x0 : SELECTS_SCK0_FUNCTIO

Selects SCK0 function in pin location SWCLK/PIO0_10/SCK0/CT16B0_MAT2 (see Table 129).

0x1 : SELECTS_SCK0_FUNCTIO

Selects SCK0 function in pin location PIO2_11/SCK0 (see Table 131).

0x1 : SELECTS_SCK0_FUNCTIO

Selects SCK0 function in pin location PIO2_11/SCK0 (see Table 131).

0x3 : RESERVED_

Reserved.

End of enumeration elements list.

RESERVED : Reserved.
bits : 2 - 33 (32 bit)


DSR_LOC

DSR pin location select register
address_offset : 0xB4 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

DSR_LOC DSR_LOC read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 DSRLOC RESERVED

DSRLOC : Selects pin location for DSR function.
bits : 0 - 1 (2 bit)

Enumeration: ENUM

0x0 : SELECTS_DSR_FUNCTIO

Selects DSR function in pin location PIO2_1/DSR/SCK1 (see Table 113).

0x1 : SELECTS_DSR_FUNCTION

Selects DSR function in pin location PIO3_1/DSR (see Table 137).

0x2 : RESERVED_

Reserved.

0x2 : RESERVED_

Reserved.

End of enumeration elements list.

RESERVED : Reserved.
bits : 2 - 33 (32 bit)


DCD_LOC

DCD pin location select register
address_offset : 0xB8 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

DCD_LOC DCD_LOC read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 DCDLOC RESERVED

DCDLOC : Selects pin location for DCD function.
bits : 0 - 1 (2 bit)

Enumeration: ENUM

0x0 : SELECTS_DCD_FUNCTIO

Selects DCD function in pin location PIO2_2/DCD/MISO1 (see Table 126).

0x1 : SELECTS_DCD_FUNCTION

Selects DCD function in pin location PIO3_2/DCD (see Table 142).

0x2 : RESERVED_

Reserved.

0x2 : RESERVED_

Reserved.

End of enumeration elements list.

RESERVED : Reserved.
bits : 2 - 33 (32 bit)


RI_LOC

RI pin location select register
address_offset : 0xBC Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

RI_LOC RI_LOC read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 RILOC RESERVED

RILOC : Selects pin location for RI function.
bits : 0 - 1 (2 bit)

Enumeration: ENUM

0x0 : SELECTS_RI_FUNCTION

Selects RI function in pin location PIO2_3/RI/MOSI1 (see Table 138).

0x1 : SELECTS_RI_FUNCTION_

Selects RI function in pin location PIO3_3/RI (see Table 146).

0x2 : RESERVED_

Reserved.

0x2 : RESERVED_

Reserved.

End of enumeration elements list.

RESERVED : Reserved.
bits : 2 - 33 (32 bit)


RESET_PIO0_0

I/O configuration for pin RESET/PIO0_0
address_offset : 0xC Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

RESET_PIO0_0 RESET_PIO0_0 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE HYS RESERVED RESERVED OD

FUNC : Selects pin function. All other values are reserved.
bits : 0 - 2 (3 bit)

Enumeration: ENUM

0x0 : SELECTS_FUNCTION_RES

Selects function RESET.

0x1 : SELECTS_FUNCTION_PIO

Selects function PIO0_0.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)

Enumeration: ENUM

0x0 : INACTIVE_NO_PULL_DO

Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN_RESISTOR_E

Pull-down resistor enabled.

0x2 : PULL_UP_RESISTOR_ENA

Pull-up resistor enabled.

0x3 : REPEATER_MODE_

Repeater mode.

End of enumeration elements list.

HYS : Hysteresis.
bits : 5 - 10 (6 bit)

Enumeration: ENUM

0 : DISABLE_

Disable.

1 : ENABLE_

Enable.

End of enumeration elements list.

RESERVED : Reserved
bits : 6 - 15 (10 bit)

RESERVED : Reserved
bits : 6 - 15 (10 bit)

OD : Selects pseudo open-drain mode.
bits : 10 - 20 (11 bit)

Enumeration: ENUM

0 : STANDARD_GPIO_OUTPUT

Standard GPIO output

1 : OPEN_DRAIN_OUTPUT

Open-drain output

End of enumeration elements list.


CT16B0_CAP0_LOC

CT16B0_CAP0 pin location select register
address_offset : 0xC0 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

CT16B0_CAP0_LOC CT16B0_CAP0_LOC read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 CT16B0_CAP0LOC RESERVED

CT16B0_CAP0LOC : Selects pin location for CT16B0_CAP0 function.
bits : 0 - 1 (2 bit)

Enumeration: ENUM

0x0 : SELECTS_CT16B0_CAP0_

Selects CT16B0_CAP0 function in pin location PIO0_2/SSEL0/CT16B0_CAP0 (see Table 110).

0x0 : SELECTS_CT16B0_CAP0_

Selects CT16B0_CAP0 function in pin location PIO0_2/SSEL0/CT16B0_CAP0 (see Table 110).

0x2 : RESERVED_

Reserved.

0x2 : RESERVED_

Reserved.

End of enumeration elements list.

RESERVED : Reserved.
bits : 2 - 33 (32 bit)


SCK1_LOC

SCK1 pin location select register
address_offset : 0xC4 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

SCK1_LOC SCK1_LOC read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SCK1LOC RESERVED

SCK1LOC : Selects pin location for SCK1 function.
bits : 0 - 1 (2 bit)

Enumeration: ENUM

0x0 : SELECTS_SCK1_FUNCTIO

Selects SCK1 function in pin location PIO2_1/DSR/SCK1 (see Table 113).

0x0 : SELECTS_SCK1_FUNCTIO

Selects SCK1 function in pin location PIO2_1/DSR/SCK1 (see Table 113).

0x2 : RESERVED_

Reserved.

0x2 : RESERVED_

Reserved.

End of enumeration elements list.

RESERVED : Reserved.
bits : 2 - 33 (32 bit)


MISO1_LOC

MISO1 pin location select register
address_offset : 0xC8 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

MISO1_LOC MISO1_LOC read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 MISO1LOC RESERVED

MISO1LOC : Selects pin location for the MISO1 function.
bits : 0 - 1 (2 bit)

Enumeration: ENUM

0x0 : SELECTS_MISO1_FUNCTI

Selects MISO1 function in pin location PIO2_2/DCD/MISO1 (see Table 126).

0x0 : SELECTS_MISO1_FUNCTI

Selects MISO1 function in pin location PIO2_2/DCD/MISO1 (see Table 126).

0x2 : RESERVED_

Reserved.

0x2 : RESERVED_

Reserved.

End of enumeration elements list.

RESERVED : Reserved.
bits : 2 - 33 (32 bit)


MOSI1_LOC

MOSI1 pin location select register
address_offset : 0xCC Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

MOSI1_LOC MOSI1_LOC read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 MOSI1LOC RESERVED

MOSI1LOC : Selects pin location for the MOSI1 function.
bits : 0 - 1 (2 bit)

Enumeration: ENUM

0x0 : SELECTS_MOSI1_FUNCTI

Selects MOSI1 function in pin location PIO2_3/RI/MOSI1 (see Table 138).

0x0 : SELECTS_MOSI1_FUNCTI

Selects MOSI1 function in pin location PIO2_3/RI/MOSI1 (see Table 138).

0x2 : RESERVED_

Reserved.

0x2 : RESERVED_

Reserved.

End of enumeration elements list.

RESERVED : Reserved.
bits : 2 - 33 (32 bit)


CT32B0_CAP0_LOC

CT32B0_CAP0 pin location select register
address_offset : 0xD0 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

CT32B0_CAP0_LOC CT32B0_CAP0_LOC read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 CT32B0_CAP0LOC RESERVED

CT32B0_CAP0LOC : Selects pin location for the CT32B0_CAP0 function.
bits : 0 - 1 (2 bit)

Enumeration: ENUM

0x0 : SELECTS_CT32B0_CAP0_

Selects CT32B0_CAP0 function in pin location PIO1_5/RTS/CT32B0_CAP0 (see Table 143).

0x0 : SELECTS_CT32B0_CAP0_

Selects CT32B0_CAP0 function in pin location PIO1_5/RTS/CT32B0_CAP0 (see Table 143).

0x2 : RESERVED_

Reserved.

0x2 : RESERVED_

Reserved.

End of enumeration elements list.

RESERVED : Reserved.
bits : 2 - 33 (32 bit)


RXD_LOC

RXD pin location select register
address_offset : 0xD4 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

RXD_LOC RXD_LOC read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 RXDLOC RESERVED

RXDLOC : Selects pin location for the RXD function.
bits : 0 - 1 (2 bit)

Enumeration: ENUM

0x0 : SELECTS_RXD_FUNCTION

Selects RXD function in pin location PIO1_6/RXD/CT32B0_MAT0 (see Table 144).

0x1 : SELECTS_RXD_FUNCTION

Selects RXD function in pin location PIO2_7/CT32B0_MAT2/RXD (see Table 111).

0x2 : SELECTS_RXD_FUNCTION

Selects RXD function in pin location PIO3_1/DSR/CT16B0_MAT1/RXD (see Table 137).

0x2 : SELECTS_RXD_FUNCTION

Selects RXD function in pin location PIO3_1/DSR/CT16B0_MAT1/RXD (see Table 137).

End of enumeration elements list.

RESERVED : Reserved.
bits : 2 - 33 (32 bit)



Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !

This website is sponsored by EmbeetleEmbeetle, an IDE designed from scratch for embedded software developers.