Embeetle, an IDE designed from scratch for embedded software developers.address_offset : 0x0 Bytes (0x0)
size : 0xFFF byte (0x0)
mem_usage : registers
protection : not protected
GPIO grouped interrupt control register
address_offset : 0x0 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
INT : Group interrupt status. This bit is cleared by writing a one to it. Writing zero has no effect.
bits : 0 - 0 (1 bit)
Enumeration: ENUM
0 : NO_INTERRUPT_REQUEST
No interrupt request is pending.
1 : INTERRUPT_REQUEST_IS
Interrupt request is active.
End of enumeration elements list.
COMB : Combine enabled inputs for group interrupt
bits : 1 - 2 (2 bit)
Enumeration: ENUM
0 : OR_FUNCTIONALITY_A_
OR functionality: A grouped interrupt is generated when any one of the enabled inputs is active (based on its programmed polarity).
1 : AND_FUNCTIONALITY_A
AND functionality: An interrupt is generated when all enabled bits are active (based on their programmed polarity).
End of enumeration elements list.
TRIG : Group interrupt trigger
bits : 2 - 4 (3 bit)
Enumeration: ENUM
0 : EDGE_TRIGGERED
Edge-triggered
1 : LEVEL_TRIGGERED
Level-triggered
End of enumeration elements list.
RESERVED : Reserved
bits : 3 - 34 (32 bit)
GPIO grouped interrupt port 0 polarity register
address_offset : 0x20 Bytes (0x0)
size : -1 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
POL_0 : Configure pin polarity of port pins for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1 . 0 = the pin is active LOW. If the level on this pin is LOW, the pin contributes to the group interrupt. 1 = the pin is active HIGH. If the level on this pin is HIGH, the pin contributes to the group interrupt.
bits : 0 - 0 (1 bit)
POL_1 : Configure pin polarity of port 0/1 pins for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the pin is active LOW. If the level on this pin is LOW, the pin contributes to the group interrupt. 1 = the pin is active HIGH. If the level on this pin is HIGH, the pin contributes to the group interrupt.
bits : 1 - 2 (2 bit)
POL_2 : Configure pin polarity of port 0/1 pins for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the pin is active LOW. If the level on this pin is LOW, the pin contributes to the group interrupt. 1 = the pin is active HIGH. If the level on this pin is HIGH, the pin contributes to the group interrupt.
bits : 2 - 4 (3 bit)
POL_3 : Configure pin polarity of port 0/1 pins for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the pin is active LOW. If the level on this pin is LOW, the pin contributes to the group interrupt. 1 = the pin is active HIGH. If the level on this pin is HIGH, the pin contributes to the group interrupt.
bits : 3 - 6 (4 bit)
POL_4 : Configure pin polarity of port 0/1 pins for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the pin is active LOW. If the level on this pin is LOW, the pin contributes to the group interrupt. 1 = the pin is active HIGH. If the level on this pin is HIGH, the pin contributes to the group interrupt.
bits : 4 - 8 (5 bit)
POL_5 : Configure pin polarity of port 0/1 pins for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the pin is active LOW. If the level on this pin is LOW, the pin contributes to the group interrupt. 1 = the pin is active HIGH. If the level on this pin is HIGH, the pin contributes to the group interrupt.
bits : 5 - 10 (6 bit)
POL_6 : Configure pin polarity of port 0/1 pins for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the pin is active LOW. If the level on this pin is LOW, the pin contributes to the group interrupt. 1 = the pin is active HIGH. If the level on this pin is HIGH, the pin contributes to the group interrupt.
bits : 6 - 12 (7 bit)
POL_7 : Configure pin polarity of port 0/1 pins for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the pin is active LOW. If the level on this pin is LOW, the pin contributes to the group interrupt. 1 = the pin is active HIGH. If the level on this pin is HIGH, the pin contributes to the group interrupt.
bits : 7 - 14 (8 bit)
POL_8 : Configure pin polarity of port 0/1 pins for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the pin is active LOW. If the level on this pin is LOW, the pin contributes to the group interrupt. 1 = the pin is active HIGH. If the level on this pin is HIGH, the pin contributes to the group interrupt.
bits : 8 - 16 (9 bit)
POL_9 : Configure pin polarity of port 0/1 pins for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the pin is active LOW. If the level on this pin is LOW, the pin contributes to the group interrupt. 1 = the pin is active HIGH. If the level on this pin is HIGH, the pin contributes to the group interrupt.
bits : 9 - 18 (10 bit)
POL_10 : Configure pin polarity of port 0/1 pins for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the pin is active LOW. If the level on this pin is LOW, the pin contributes to the group interrupt. 1 = the pin is active HIGH. If the level on this pin is HIGH, the pin contributes to the group interrupt.
bits : 10 - 20 (11 bit)
POL_11 : Configure pin polarity of port 0/1 pins for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the pin is active LOW. If the level on this pin is LOW, the pin contributes to the group interrupt. 1 = the pin is active HIGH. If the level on this pin is HIGH, the pin contributes to the group interrupt.
bits : 11 - 22 (12 bit)
POL_12 : Configure pin polarity of port 0/1 pins for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the pin is active LOW. If the level on this pin is LOW, the pin contributes to the group interrupt. 1 = the pin is active HIGH. If the level on this pin is HIGH, the pin contributes to the group interrupt.
bits : 12 - 24 (13 bit)
POL_13 : Configure pin polarity of port 0/1 pins for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the pin is active LOW. If the level on this pin is LOW, the pin contributes to the group interrupt. 1 = the pin is active HIGH. If the level on this pin is HIGH, the pin contributes to the group interrupt.
bits : 13 - 26 (14 bit)
POL_14 : Configure pin polarity of port 0/1 pins for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the pin is active LOW. If the level on this pin is LOW, the pin contributes to the group interrupt. 1 = the pin is active HIGH. If the level on this pin is HIGH, the pin contributes to the group interrupt.
bits : 14 - 28 (15 bit)
POL_15 : Configure pin polarity of port 0/1 pins for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the pin is active LOW. If the level on this pin is LOW, the pin contributes to the group interrupt. 1 = the pin is active HIGH. If the level on this pin is HIGH, the pin contributes to the group interrupt.
bits : 15 - 30 (16 bit)
POL_16 : Configure pin polarity of port 0/1 pins for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the pin is active LOW. If the level on this pin is LOW, the pin contributes to the group interrupt. 1 = the pin is active HIGH. If the level on this pin is HIGH, the pin contributes to the group interrupt.
bits : 16 - 32 (17 bit)
POL_17 : Configure pin polarity of port 0/1 pins for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the pin is active LOW. If the level on this pin is LOW, the pin contributes to the group interrupt. 1 = the pin is active HIGH. If the level on this pin is HIGH, the pin contributes to the group interrupt.
bits : 17 - 34 (18 bit)
POL_18 : Configure pin polarity of port 0/1 pins for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the pin is active LOW. If the level on this pin is LOW, the pin contributes to the group interrupt. 1 = the pin is active HIGH. If the level on this pin is HIGH, the pin contributes to the group interrupt.
bits : 18 - 36 (19 bit)
POL_19 : Configure pin polarity of port 0/1 pins for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the pin is active LOW. If the level on this pin is LOW, the pin contributes to the group interrupt. 1 = the pin is active HIGH. If the level on this pin is HIGH, the pin contributes to the group interrupt.
bits : 19 - 38 (20 bit)
POL_20 : Configure pin polarity of port 0/1 pins for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the pin is active LOW. If the level on this pin is LOW, the pin contributes to the group interrupt. 1 = the pin is active HIGH. If the level on this pin is HIGH, the pin contributes to the group interrupt.
bits : 20 - 40 (21 bit)
POL_21 : Configure pin polarity of port 0/1 pins for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the pin is active LOW. If the level on this pin is LOW, the pin contributes to the group interrupt. 1 = the pin is active HIGH. If the level on this pin is HIGH, the pin contributes to the group interrupt.
bits : 21 - 42 (22 bit)
POL_22 : Configure pin polarity of port 0/1 pins for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the pin is active LOW. If the level on this pin is LOW, the pin contributes to the group interrupt. 1 = the pin is active HIGH. If the level on this pin is HIGH, the pin contributes to the group interrupt.
bits : 22 - 44 (23 bit)
POL_23 : Configure pin polarity of port 0/1 pins for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the pin is active LOW. If the level on this pin is LOW, the pin contributes to the group interrupt. 1 = the pin is active HIGH. If the level on this pin is HIGH, the pin contributes to the group interrupt.
bits : 23 - 46 (24 bit)
POL_24 : Configure pin polarity of port 0/1 pins for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the pin is active LOW. If the level on this pin is LOW, the pin contributes to the group interrupt. 1 = the pin is active HIGH. If the level on this pin is HIGH, the pin contributes to the group interrupt.
bits : 24 - 48 (25 bit)
POL_25 : Configure pin polarity of port 0/1 pins for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the pin is active LOW. If the level on this pin is LOW, the pin contributes to the group interrupt. 1 = the pin is active HIGH. If the level on this pin is HIGH, the pin contributes to the group interrupt.
bits : 25 - 50 (26 bit)
POL_26 : Configure pin polarity of port 0/1 pins for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the pin is active LOW. If the level on this pin is LOW, the pin contributes to the group interrupt. 1 = the pin is active HIGH. If the level on this pin is HIGH, the pin contributes to the group interrupt.
bits : 26 - 52 (27 bit)
POL_27 : Configure pin polarity of port 0/1 pins for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the pin is active LOW. If the level on this pin is LOW, the pin contributes to the group interrupt. 1 = the pin is active HIGH. If the level on this pin is HIGH, the pin contributes to the group interrupt.
bits : 27 - 54 (28 bit)
POL_28 : Configure pin polarity of port 0/1 pins for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the pin is active LOW. If the level on this pin is LOW, the pin contributes to the group interrupt. 1 = the pin is active HIGH. If the level on this pin is HIGH, the pin contributes to the group interrupt.
bits : 28 - 56 (29 bit)
POL_29 : Configure pin polarity of port 0/1 pins for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the pin is active LOW. If the level on this pin is LOW, the pin contributes to the group interrupt. 1 = the pin is active HIGH. If the level on this pin is HIGH, the pin contributes to the group interrupt.
bits : 29 - 58 (30 bit)
POL_30 : Configure pin polarity of port 0/1 pins for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the pin is active LOW. If the level on this pin is LOW, the pin contributes to the group interrupt. 1 = the pin is active HIGH. If the level on this pin is HIGH, the pin contributes to the group interrupt.
bits : 30 - 60 (31 bit)
POL_31 : Configure pin polarity of port 0/1 pins for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the pin is active LOW. If the level on this pin is LOW, the pin contributes to the group interrupt. 1 = the pin is active HIGH. If the level on this pin is HIGH, the pin contributes to the group interrupt.
bits : 31 - 62 (32 bit)
GPIO grouped interrupt port 0 polarity register
address_offset : 0x24 Bytes (0x0)
size : -1 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
POL_0 : Configure pin polarity of port pins for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1 . 0 = the pin is active LOW. If the level on this pin is LOW, the pin contributes to the group interrupt. 1 = the pin is active HIGH. If the level on this pin is HIGH, the pin contributes to the group interrupt.
bits : 0 - 0 (1 bit)
POL_1 : Configure pin polarity of port 0/1 pins for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the pin is active LOW. If the level on this pin is LOW, the pin contributes to the group interrupt. 1 = the pin is active HIGH. If the level on this pin is HIGH, the pin contributes to the group interrupt.
bits : 1 - 2 (2 bit)
POL_2 : Configure pin polarity of port 0/1 pins for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the pin is active LOW. If the level on this pin is LOW, the pin contributes to the group interrupt. 1 = the pin is active HIGH. If the level on this pin is HIGH, the pin contributes to the group interrupt.
bits : 2 - 4 (3 bit)
POL_3 : Configure pin polarity of port 0/1 pins for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the pin is active LOW. If the level on this pin is LOW, the pin contributes to the group interrupt. 1 = the pin is active HIGH. If the level on this pin is HIGH, the pin contributes to the group interrupt.
bits : 3 - 6 (4 bit)
POL_4 : Configure pin polarity of port 0/1 pins for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the pin is active LOW. If the level on this pin is LOW, the pin contributes to the group interrupt. 1 = the pin is active HIGH. If the level on this pin is HIGH, the pin contributes to the group interrupt.
bits : 4 - 8 (5 bit)
POL_5 : Configure pin polarity of port 0/1 pins for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the pin is active LOW. If the level on this pin is LOW, the pin contributes to the group interrupt. 1 = the pin is active HIGH. If the level on this pin is HIGH, the pin contributes to the group interrupt.
bits : 5 - 10 (6 bit)
POL_6 : Configure pin polarity of port 0/1 pins for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the pin is active LOW. If the level on this pin is LOW, the pin contributes to the group interrupt. 1 = the pin is active HIGH. If the level on this pin is HIGH, the pin contributes to the group interrupt.
bits : 6 - 12 (7 bit)
POL_7 : Configure pin polarity of port 0/1 pins for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the pin is active LOW. If the level on this pin is LOW, the pin contributes to the group interrupt. 1 = the pin is active HIGH. If the level on this pin is HIGH, the pin contributes to the group interrupt.
bits : 7 - 14 (8 bit)
POL_8 : Configure pin polarity of port 0/1 pins for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the pin is active LOW. If the level on this pin is LOW, the pin contributes to the group interrupt. 1 = the pin is active HIGH. If the level on this pin is HIGH, the pin contributes to the group interrupt.
bits : 8 - 16 (9 bit)
POL_9 : Configure pin polarity of port 0/1 pins for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the pin is active LOW. If the level on this pin is LOW, the pin contributes to the group interrupt. 1 = the pin is active HIGH. If the level on this pin is HIGH, the pin contributes to the group interrupt.
bits : 9 - 18 (10 bit)
POL_10 : Configure pin polarity of port 0/1 pins for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the pin is active LOW. If the level on this pin is LOW, the pin contributes to the group interrupt. 1 = the pin is active HIGH. If the level on this pin is HIGH, the pin contributes to the group interrupt.
bits : 10 - 20 (11 bit)
POL_11 : Configure pin polarity of port 0/1 pins for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the pin is active LOW. If the level on this pin is LOW, the pin contributes to the group interrupt. 1 = the pin is active HIGH. If the level on this pin is HIGH, the pin contributes to the group interrupt.
bits : 11 - 22 (12 bit)
POL_12 : Configure pin polarity of port 0/1 pins for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the pin is active LOW. If the level on this pin is LOW, the pin contributes to the group interrupt. 1 = the pin is active HIGH. If the level on this pin is HIGH, the pin contributes to the group interrupt.
bits : 12 - 24 (13 bit)
POL_13 : Configure pin polarity of port 0/1 pins for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the pin is active LOW. If the level on this pin is LOW, the pin contributes to the group interrupt. 1 = the pin is active HIGH. If the level on this pin is HIGH, the pin contributes to the group interrupt.
bits : 13 - 26 (14 bit)
POL_14 : Configure pin polarity of port 0/1 pins for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the pin is active LOW. If the level on this pin is LOW, the pin contributes to the group interrupt. 1 = the pin is active HIGH. If the level on this pin is HIGH, the pin contributes to the group interrupt.
bits : 14 - 28 (15 bit)
POL_15 : Configure pin polarity of port 0/1 pins for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the pin is active LOW. If the level on this pin is LOW, the pin contributes to the group interrupt. 1 = the pin is active HIGH. If the level on this pin is HIGH, the pin contributes to the group interrupt.
bits : 15 - 30 (16 bit)
POL_16 : Configure pin polarity of port 0/1 pins for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the pin is active LOW. If the level on this pin is LOW, the pin contributes to the group interrupt. 1 = the pin is active HIGH. If the level on this pin is HIGH, the pin contributes to the group interrupt.
bits : 16 - 32 (17 bit)
POL_17 : Configure pin polarity of port 0/1 pins for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the pin is active LOW. If the level on this pin is LOW, the pin contributes to the group interrupt. 1 = the pin is active HIGH. If the level on this pin is HIGH, the pin contributes to the group interrupt.
bits : 17 - 34 (18 bit)
POL_18 : Configure pin polarity of port 0/1 pins for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the pin is active LOW. If the level on this pin is LOW, the pin contributes to the group interrupt. 1 = the pin is active HIGH. If the level on this pin is HIGH, the pin contributes to the group interrupt.
bits : 18 - 36 (19 bit)
POL_19 : Configure pin polarity of port 0/1 pins for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the pin is active LOW. If the level on this pin is LOW, the pin contributes to the group interrupt. 1 = the pin is active HIGH. If the level on this pin is HIGH, the pin contributes to the group interrupt.
bits : 19 - 38 (20 bit)
POL_20 : Configure pin polarity of port 0/1 pins for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the pin is active LOW. If the level on this pin is LOW, the pin contributes to the group interrupt. 1 = the pin is active HIGH. If the level on this pin is HIGH, the pin contributes to the group interrupt.
bits : 20 - 40 (21 bit)
POL_21 : Configure pin polarity of port 0/1 pins for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the pin is active LOW. If the level on this pin is LOW, the pin contributes to the group interrupt. 1 = the pin is active HIGH. If the level on this pin is HIGH, the pin contributes to the group interrupt.
bits : 21 - 42 (22 bit)
POL_22 : Configure pin polarity of port 0/1 pins for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the pin is active LOW. If the level on this pin is LOW, the pin contributes to the group interrupt. 1 = the pin is active HIGH. If the level on this pin is HIGH, the pin contributes to the group interrupt.
bits : 22 - 44 (23 bit)
POL_23 : Configure pin polarity of port 0/1 pins for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the pin is active LOW. If the level on this pin is LOW, the pin contributes to the group interrupt. 1 = the pin is active HIGH. If the level on this pin is HIGH, the pin contributes to the group interrupt.
bits : 23 - 46 (24 bit)
POL_24 : Configure pin polarity of port 0/1 pins for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the pin is active LOW. If the level on this pin is LOW, the pin contributes to the group interrupt. 1 = the pin is active HIGH. If the level on this pin is HIGH, the pin contributes to the group interrupt.
bits : 24 - 48 (25 bit)
POL_25 : Configure pin polarity of port 0/1 pins for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the pin is active LOW. If the level on this pin is LOW, the pin contributes to the group interrupt. 1 = the pin is active HIGH. If the level on this pin is HIGH, the pin contributes to the group interrupt.
bits : 25 - 50 (26 bit)
POL_26 : Configure pin polarity of port 0/1 pins for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the pin is active LOW. If the level on this pin is LOW, the pin contributes to the group interrupt. 1 = the pin is active HIGH. If the level on this pin is HIGH, the pin contributes to the group interrupt.
bits : 26 - 52 (27 bit)
POL_27 : Configure pin polarity of port 0/1 pins for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the pin is active LOW. If the level on this pin is LOW, the pin contributes to the group interrupt. 1 = the pin is active HIGH. If the level on this pin is HIGH, the pin contributes to the group interrupt.
bits : 27 - 54 (28 bit)
POL_28 : Configure pin polarity of port 0/1 pins for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the pin is active LOW. If the level on this pin is LOW, the pin contributes to the group interrupt. 1 = the pin is active HIGH. If the level on this pin is HIGH, the pin contributes to the group interrupt.
bits : 28 - 56 (29 bit)
POL_29 : Configure pin polarity of port 0/1 pins for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the pin is active LOW. If the level on this pin is LOW, the pin contributes to the group interrupt. 1 = the pin is active HIGH. If the level on this pin is HIGH, the pin contributes to the group interrupt.
bits : 29 - 58 (30 bit)
POL_30 : Configure pin polarity of port 0/1 pins for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the pin is active LOW. If the level on this pin is LOW, the pin contributes to the group interrupt. 1 = the pin is active HIGH. If the level on this pin is HIGH, the pin contributes to the group interrupt.
bits : 30 - 60 (31 bit)
POL_31 : Configure pin polarity of port 0/1 pins for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the pin is active LOW. If the level on this pin is LOW, the pin contributes to the group interrupt. 1 = the pin is active HIGH. If the level on this pin is HIGH, the pin contributes to the group interrupt.
bits : 31 - 62 (32 bit)
GPIO grouped interrupt port 0/1 enable register
address_offset : 0x40 Bytes (0x0)
size : -1 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
ENA_0 : Enable port 0/1 pin for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the port 0/1 pin is disabled and does not contribute to the grouped interrupt. 1 = the port 0/1 pin is enabled and contributes to the grouped interrupt.
bits : 0 - 0 (1 bit)
ENA_1 : Enable port 0/1 pin for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the port 0/1 pin is disabled and does not contribute to the grouped interrupt. 1 = the port 0/1 pin is enabled and contributes to the grouped interrupt.
bits : 1 - 2 (2 bit)
ENA_2 : Enable port 0/1 pin for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the port 0/1 pin is disabled and does not contribute to the grouped interrupt. 1 = the port 0/1 pin is enabled and contributes to the grouped interrupt.
bits : 2 - 4 (3 bit)
ENA_3 : Enable port 0/1 pin for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the port 0/1 pin is disabled and does not contribute to the grouped interrupt. 1 = the port 0/1 pin is enabled and contributes to the grouped interrupt.
bits : 3 - 6 (4 bit)
ENA_4 : Enable port 0/1 pin for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the port 0/1 pin is disabled and does not contribute to the grouped interrupt. 1 = the port 0/1 pin is enabled and contributes to the grouped interrupt.
bits : 4 - 8 (5 bit)
ENA_5 : Enable port 0/1 pin for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the port 0/1 pin is disabled and does not contribute to the grouped interrupt. 1 = the port 0/1 pin is enabled and contributes to the grouped interrupt.
bits : 5 - 10 (6 bit)
ENA_6 : Enable port 0/1 pin for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the port 0/1 pin is disabled and does not contribute to the grouped interrupt. 1 = the port 0/1 pin is enabled and contributes to the grouped interrupt.
bits : 6 - 12 (7 bit)
ENA_7 : Enable port 0/1 pin for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the port 0/1 pin is disabled and does not contribute to the grouped interrupt. 1 = the port 0/1 pin is enabled and contributes to the grouped interrupt.
bits : 7 - 14 (8 bit)
ENA_8 : Enable port 0/1 pin for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the port 0/1 pin is disabled and does not contribute to the grouped interrupt. 1 = the port 0/1 pin is enabled and contributes to the grouped interrupt.
bits : 8 - 16 (9 bit)
ENA_9 : Enable port 0/1 pin for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the port 0/1 pin is disabled and does not contribute to the grouped interrupt. 1 = the port 0/1 pin is enabled and contributes to the grouped interrupt.
bits : 9 - 18 (10 bit)
ENA_10 : Enable port 0/1 pin for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the port 0/1 pin is disabled and does not contribute to the grouped interrupt. 1 = the port 0/1 pin is enabled and contributes to the grouped interrupt.
bits : 10 - 20 (11 bit)
ENA_11 : Enable port 0/1 pin for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the port 0/1 pin is disabled and does not contribute to the grouped interrupt. 1 = the port 0/1 pin is enabled and contributes to the grouped interrupt.
bits : 11 - 22 (12 bit)
ENA_12 : Enable port 0/1 pin for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the port 0/1 pin is disabled and does not contribute to the grouped interrupt. 1 = the port 0/1 pin is enabled and contributes to the grouped interrupt.
bits : 12 - 24 (13 bit)
ENA_13 : Enable port 0/1 pin for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the port 0/1 pin is disabled and does not contribute to the grouped interrupt. 1 = the port 0/1 pin is enabled and contributes to the grouped interrupt.
bits : 13 - 26 (14 bit)
ENA_14 : Enable port 0/1 pin for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the port 0/1 pin is disabled and does not contribute to the grouped interrupt. 1 = the port 0/1 pin is enabled and contributes to the grouped interrupt.
bits : 14 - 28 (15 bit)
ENA_15 : Enable port 0/1 pin for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the port 0/1 pin is disabled and does not contribute to the grouped interrupt. 1 = the port 0/1 pin is enabled and contributes to the grouped interrupt.
bits : 15 - 30 (16 bit)
ENA_16 : Enable port 0/1 pin for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the port 0/1 pin is disabled and does not contribute to the grouped interrupt. 1 = the port 0/1 pin is enabled and contributes to the grouped interrupt.
bits : 16 - 32 (17 bit)
ENA_17 : Enable port 0/1 pin for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the port 0/1 pin is disabled and does not contribute to the grouped interrupt. 1 = the port 0/1 pin is enabled and contributes to the grouped interrupt.
bits : 17 - 34 (18 bit)
ENA_18 : Enable port 0/1 pin for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the port 0/1 pin is disabled and does not contribute to the grouped interrupt. 1 = the port 0/1 pin is enabled and contributes to the grouped interrupt.
bits : 18 - 36 (19 bit)
ENA_19 : Enable port 0/1 pin for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the port 0/1 pin is disabled and does not contribute to the grouped interrupt. 1 = the port 0/1 pin is enabled and contributes to the grouped interrupt.
bits : 19 - 38 (20 bit)
ENA_20 : Enable port 0/1 pin for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the port 0/1 pin is disabled and does not contribute to the grouped interrupt. 1 = the port 0/1 pin is enabled and contributes to the grouped interrupt.
bits : 20 - 40 (21 bit)
ENA_21 : Enable port 0/1 pin for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the port 0/1 pin is disabled and does not contribute to the grouped interrupt. 1 = the port 0/1 pin is enabled and contributes to the grouped interrupt.
bits : 21 - 42 (22 bit)
ENA_22 : Enable port 0/1 pin for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the port 0/1 pin is disabled and does not contribute to the grouped interrupt. 1 = the port 0/1 pin is enabled and contributes to the grouped interrupt.
bits : 22 - 44 (23 bit)
ENA_23 : Enable port 0/1 pin for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the port 0/1 pin is disabled and does not contribute to the grouped interrupt. 1 = the port 0/1 pin is enabled and contributes to the grouped interrupt.
bits : 23 - 46 (24 bit)
ENA_24 : Enable port 0/1 pin for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the port 0/1 pin is disabled and does not contribute to the grouped interrupt. 1 = the port 0/1 pin is enabled and contributes to the grouped interrupt.
bits : 24 - 48 (25 bit)
ENA_25 : Enable port 0/1 pin for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the port 0/1 pin is disabled and does not contribute to the grouped interrupt. 1 = the port 0/1 pin is enabled and contributes to the grouped interrupt.
bits : 25 - 50 (26 bit)
ENA_26 : Enable port 0/1 pin for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the port 0/1 pin is disabled and does not contribute to the grouped interrupt. 1 = the port 0/1 pin is enabled and contributes to the grouped interrupt.
bits : 26 - 52 (27 bit)
ENA_27 : Enable port 0/1 pin for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the port 0/1 pin is disabled and does not contribute to the grouped interrupt. 1 = the port 0/1 pin is enabled and contributes to the grouped interrupt.
bits : 27 - 54 (28 bit)
ENA_28 : Enable port 0/1 pin for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the port 0/1 pin is disabled and does not contribute to the grouped interrupt. 1 = the port 0/1 pin is enabled and contributes to the grouped interrupt.
bits : 28 - 56 (29 bit)
ENA_29 : Enable port 0/1 pin for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the port 0/1 pin is disabled and does not contribute to the grouped interrupt. 1 = the port 0/1 pin is enabled and contributes to the grouped interrupt.
bits : 29 - 58 (30 bit)
ENA_30 : Enable port 0/1 pin for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the port 0/1 pin is disabled and does not contribute to the grouped interrupt. 1 = the port 0/1 pin is enabled and contributes to the grouped interrupt.
bits : 30 - 60 (31 bit)
ENA_31 : Enable port 0/1 pin for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the port 0/1 pin is disabled and does not contribute to the grouped interrupt. 1 = the port 0/1 pin is enabled and contributes to the grouped interrupt.
bits : 31 - 62 (32 bit)
GPIO grouped interrupt port 0/1 enable register
address_offset : 0x44 Bytes (0x0)
size : -1 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
ENA_0 : Enable port 0/1 pin for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the port 0/1 pin is disabled and does not contribute to the grouped interrupt. 1 = the port 0/1 pin is enabled and contributes to the grouped interrupt.
bits : 0 - 0 (1 bit)
ENA_1 : Enable port 0/1 pin for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the port 0/1 pin is disabled and does not contribute to the grouped interrupt. 1 = the port 0/1 pin is enabled and contributes to the grouped interrupt.
bits : 1 - 2 (2 bit)
ENA_2 : Enable port 0/1 pin for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the port 0/1 pin is disabled and does not contribute to the grouped interrupt. 1 = the port 0/1 pin is enabled and contributes to the grouped interrupt.
bits : 2 - 4 (3 bit)
ENA_3 : Enable port 0/1 pin for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the port 0/1 pin is disabled and does not contribute to the grouped interrupt. 1 = the port 0/1 pin is enabled and contributes to the grouped interrupt.
bits : 3 - 6 (4 bit)
ENA_4 : Enable port 0/1 pin for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the port 0/1 pin is disabled and does not contribute to the grouped interrupt. 1 = the port 0/1 pin is enabled and contributes to the grouped interrupt.
bits : 4 - 8 (5 bit)
ENA_5 : Enable port 0/1 pin for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the port 0/1 pin is disabled and does not contribute to the grouped interrupt. 1 = the port 0/1 pin is enabled and contributes to the grouped interrupt.
bits : 5 - 10 (6 bit)
ENA_6 : Enable port 0/1 pin for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the port 0/1 pin is disabled and does not contribute to the grouped interrupt. 1 = the port 0/1 pin is enabled and contributes to the grouped interrupt.
bits : 6 - 12 (7 bit)
ENA_7 : Enable port 0/1 pin for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the port 0/1 pin is disabled and does not contribute to the grouped interrupt. 1 = the port 0/1 pin is enabled and contributes to the grouped interrupt.
bits : 7 - 14 (8 bit)
ENA_8 : Enable port 0/1 pin for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the port 0/1 pin is disabled and does not contribute to the grouped interrupt. 1 = the port 0/1 pin is enabled and contributes to the grouped interrupt.
bits : 8 - 16 (9 bit)
ENA_9 : Enable port 0/1 pin for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the port 0/1 pin is disabled and does not contribute to the grouped interrupt. 1 = the port 0/1 pin is enabled and contributes to the grouped interrupt.
bits : 9 - 18 (10 bit)
ENA_10 : Enable port 0/1 pin for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the port 0/1 pin is disabled and does not contribute to the grouped interrupt. 1 = the port 0/1 pin is enabled and contributes to the grouped interrupt.
bits : 10 - 20 (11 bit)
ENA_11 : Enable port 0/1 pin for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the port 0/1 pin is disabled and does not contribute to the grouped interrupt. 1 = the port 0/1 pin is enabled and contributes to the grouped interrupt.
bits : 11 - 22 (12 bit)
ENA_12 : Enable port 0/1 pin for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the port 0/1 pin is disabled and does not contribute to the grouped interrupt. 1 = the port 0/1 pin is enabled and contributes to the grouped interrupt.
bits : 12 - 24 (13 bit)
ENA_13 : Enable port 0/1 pin for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the port 0/1 pin is disabled and does not contribute to the grouped interrupt. 1 = the port 0/1 pin is enabled and contributes to the grouped interrupt.
bits : 13 - 26 (14 bit)
ENA_14 : Enable port 0/1 pin for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the port 0/1 pin is disabled and does not contribute to the grouped interrupt. 1 = the port 0/1 pin is enabled and contributes to the grouped interrupt.
bits : 14 - 28 (15 bit)
ENA_15 : Enable port 0/1 pin for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the port 0/1 pin is disabled and does not contribute to the grouped interrupt. 1 = the port 0/1 pin is enabled and contributes to the grouped interrupt.
bits : 15 - 30 (16 bit)
ENA_16 : Enable port 0/1 pin for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the port 0/1 pin is disabled and does not contribute to the grouped interrupt. 1 = the port 0/1 pin is enabled and contributes to the grouped interrupt.
bits : 16 - 32 (17 bit)
ENA_17 : Enable port 0/1 pin for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the port 0/1 pin is disabled and does not contribute to the grouped interrupt. 1 = the port 0/1 pin is enabled and contributes to the grouped interrupt.
bits : 17 - 34 (18 bit)
ENA_18 : Enable port 0/1 pin for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the port 0/1 pin is disabled and does not contribute to the grouped interrupt. 1 = the port 0/1 pin is enabled and contributes to the grouped interrupt.
bits : 18 - 36 (19 bit)
ENA_19 : Enable port 0/1 pin for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the port 0/1 pin is disabled and does not contribute to the grouped interrupt. 1 = the port 0/1 pin is enabled and contributes to the grouped interrupt.
bits : 19 - 38 (20 bit)
ENA_20 : Enable port 0/1 pin for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the port 0/1 pin is disabled and does not contribute to the grouped interrupt. 1 = the port 0/1 pin is enabled and contributes to the grouped interrupt.
bits : 20 - 40 (21 bit)
ENA_21 : Enable port 0/1 pin for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the port 0/1 pin is disabled and does not contribute to the grouped interrupt. 1 = the port 0/1 pin is enabled and contributes to the grouped interrupt.
bits : 21 - 42 (22 bit)
ENA_22 : Enable port 0/1 pin for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the port 0/1 pin is disabled and does not contribute to the grouped interrupt. 1 = the port 0/1 pin is enabled and contributes to the grouped interrupt.
bits : 22 - 44 (23 bit)
ENA_23 : Enable port 0/1 pin for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the port 0/1 pin is disabled and does not contribute to the grouped interrupt. 1 = the port 0/1 pin is enabled and contributes to the grouped interrupt.
bits : 23 - 46 (24 bit)
ENA_24 : Enable port 0/1 pin for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the port 0/1 pin is disabled and does not contribute to the grouped interrupt. 1 = the port 0/1 pin is enabled and contributes to the grouped interrupt.
bits : 24 - 48 (25 bit)
ENA_25 : Enable port 0/1 pin for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the port 0/1 pin is disabled and does not contribute to the grouped interrupt. 1 = the port 0/1 pin is enabled and contributes to the grouped interrupt.
bits : 25 - 50 (26 bit)
ENA_26 : Enable port 0/1 pin for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the port 0/1 pin is disabled and does not contribute to the grouped interrupt. 1 = the port 0/1 pin is enabled and contributes to the grouped interrupt.
bits : 26 - 52 (27 bit)
ENA_27 : Enable port 0/1 pin for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the port 0/1 pin is disabled and does not contribute to the grouped interrupt. 1 = the port 0/1 pin is enabled and contributes to the grouped interrupt.
bits : 27 - 54 (28 bit)
ENA_28 : Enable port 0/1 pin for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the port 0/1 pin is disabled and does not contribute to the grouped interrupt. 1 = the port 0/1 pin is enabled and contributes to the grouped interrupt.
bits : 28 - 56 (29 bit)
ENA_29 : Enable port 0/1 pin for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the port 0/1 pin is disabled and does not contribute to the grouped interrupt. 1 = the port 0/1 pin is enabled and contributes to the grouped interrupt.
bits : 29 - 58 (30 bit)
ENA_30 : Enable port 0/1 pin for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the port 0/1 pin is disabled and does not contribute to the grouped interrupt. 1 = the port 0/1 pin is enabled and contributes to the grouped interrupt.
bits : 30 - 60 (31 bit)
ENA_31 : Enable port 0/1 pin for group interrupt. Bit n corresponds to pin P0/1_n of port 0/1. 0 = the port 0/1 pin is disabled and does not contribute to the grouped interrupt. 1 = the port 0/1 pin is enabled and contributes to the grouped interrupt.
bits : 31 - 62 (32 bit)
Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !
This website is sponsored by Embeetle, an IDE designed from scratch for embedded software developers.