Embeetle, an IDE designed from scratch for embedded software developers.address_offset : 0x0 Bytes (0x0)
size : 0xFFF byte (0x0)
mem_usage : registers
protection : not protected
I/O configuration register for pin P0[0]
address_offset : 0x0 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P0[0]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P0_0
General purpose digital input/output pin.
0x1 : CAN_RD1
CAN1 receiver input.
0x2 : U3_TXD
Transmitter output for UART3.
0x3 : I2C1_SDA
I2C1 data input/output (this pin does not use a specialized I2C pad).
0x4 : U0_TXD
Transmitter output for UART0.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P0[4]
address_offset : 0x10 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P0[4]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P0_4
General purpose digital input/output pin.
0x1 : I2S_RX_SCK
I2S Receive clock. It is driven by the master and received by the slave. Corresponds to the signal SCK in the I2S-bus specification.
0x2 : CAN_RD2
CAN2 receiver input.
0x3 : T2_CAP0
Capture input for Timer 2, channel 0.
0x5 : CMP_ROSC
Comparator relaxation oscillator for 555 timer applications.
0x7 : LCD_VD_0
LCD data.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P2[0]
address_offset : 0x100 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P2[0]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P2_0
General purpose digital input/output pin.
0x1 : PWM1_1
Pulse Width Modulator 1, channel 1 output.
0x2 : U1_TXD
Transmitter output for UART1.
0x7 : LCD_PWR
LCD panel power enable.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P2[1]
address_offset : 0x104 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P2[1]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P2_1
General purpose digital input/output pin.
0x1 : PWM1_2
Pulse Width Modulator 1, channel 2 output.
0x2 : U1_RXD
Receiver input for UART1.
0x7 : LCD_LE
Line end signal.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P2[2]
address_offset : 0x108 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P2[2]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P2_2
General purpose digital input/output pin.
0x1 : PWM1_3
Pulse Width Modulator 1, channel 3 output.
0x2 : U1_CTS
Clear to Send input for UART1.
0x3 : T2_MAT3
Match output for Timer 2, channel 3.
0x5 : TRACEDATA_3
Trace data, bit 3.
0x7 : LCD_DCLK
LCD panel clock.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P2[3]
address_offset : 0x10C Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P2[3]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P2_3
General purpose digital input/output pin.
0x1 : PWM1_4
Pulse Width Modulator 1, channel 4 output.
0x2 : U1_DCD
Data Carrier Detect input for UART1.
0x3 : T2_MAT2
Match output for Timer 2, channel 2.
0x5 : TRACEDATA_2
Trace data, bit 2.
0x7 : LCD_FP
Frame pulse (STN). Vertical synchronization pulse (TFT).
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P2[4]
address_offset : 0x110 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P2[4]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P2_4
General purpose digital input/output pin.
0x1 : PWM1_5
Pulse Width Modulator 1, channel 5 output.
0x2 : U1_DSR
Data Set Ready input for UART1.
0x3 : T2_MAT1
Match output for Timer 2, channel 1.
0x5 : TRACEDATA_1
Trace data, bit 1.
0x7 : LCD_ENAB_M
STN AC bias drive or TFT data enable output.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P2[5]
address_offset : 0x114 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P2[5]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P2_5
General purpose digital input/output pin.
0x1 : PWM1_6
Pulse Width Modulator 1, channel 6 output.
0x2 : U1_DTR
Data Terminal Ready output for UART1. Can also be configured to be an RS-485/EIA-485 output enable signal for UART1.
0x3 : T2_MAT0
Match output for Timer 2, channel 0.
0x5 : TRACEDATA_0
Trace data, bit 0.
0x7 : LCD_LP
Line synchronization pulse (STN). Horizontal synchronization pulse (TFT).
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P2[6]
address_offset : 0x118 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P2[6]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P2_6
General purpose digital input/output pin.
0x1 : PWM1_CAP0
Capture input for PWM1, channel 0.
0x2 : U1_RI
Ring Indicator input for UART1.
0x3 : T2_CAP0
Capture input for Timer 2, channel 0.
0x4 : U2_OE
RS-485/EIA-485 output enable signal for UART2.
0x5 : TRACECLK
Trace clock.
0x6 : LCD_VD_0
LCD data.
0x7 : LCD_VD_4
LCD data.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P2[7]
address_offset : 0x11C Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P2[7]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P2_7
General purpose digital input/output pin.
0x1 : CAN_RD2
CAN2 receiver input.
0x2 : U1_RTS
Request to Send output for UART1. Can also be configured to be an RS-485/EIA-485 output enable signal for UART1.
0x5 : SPIFI_CS
Chip select output for SPIFI.
0x6 : LCD_VD_1
LCD data.
0x7 : LCD_VD_5
LCD data.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P2[8]
address_offset : 0x120 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P2[8]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P2_8
General purpose digital input/output pin.
0x1 : CAN_TD2
CAN2 transmitter output.
0x2 : U2_TXD
Transmitter output for UART2.
0x3 : U1_CTS
Clear to Send input for UART1.
0x4 : ENET_MDC
Ethernet MIIM clock.
0x6 : LCD_VD_2
LCD data.
0x7 : LCD_VD_6
LCD data.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P2[9]
address_offset : 0x124 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P2[9]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P2_9
General purpose digital input/output pin.
0x1 : USB_CONNECT1
USB1 SoftConnect control. Signal used to switch an external 1.5 kW resistor under the software control. Used with the SoftConnect USB feature.
0x2 : U2_RXD
Receiver input for UART2.
0x3 : U4_RXD
Receiver input for USART4.
0x4 : ENET_MDIO
Ethernet MIIM data input and output.
0x6 : LCD_VD_3
LCD data.
0x7 : LCD_VD_7
LCD data.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P2[10]
address_offset : 0x128 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P2[10]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P2_10
General purpose digital input/output pin. This pin includes a 5 ns input glitch filter.A LOW on this pin while RESET is LOW forces the on-chip boot loader to take over control of the part after a reset and go into ISP mode.
0x1 : EINT0
External interrupt 0 input.
0x2 : NMI
Non-maskable interrupt input.
End of enumeration elements list.
I/O configuration register for pin P2[11]
address_offset : 0x12C Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P2[11]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P2_11
General purpose digital input/output pin. This pin includes a 5 ns input glitch filter.
0x1 : EINT1
External interrupt 1 input.
0x2 : SD_DAT_1
Data line 1 for SD card interface.
0x3 : I2S_TX_SCK
Transmit Clock. It is driven by the master and received by the slave. Corresponds to the signal SCK in the I2S-bus specification.
0x7 : LCD_CLKIN
LCD clock.
End of enumeration elements list.
I/O configuration register for pin P2[12]
address_offset : 0x130 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P2[12]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P2_12
General purpose digital input/output pin. This pin includes a 5 ns input glitch filter.
0x1 : EINT2
External interrupt 2 input.
0x2 : SD_DAT_2
Data line 2 for SD card interface.
0x3 : I2S_TX_WS
Transmit Word Select. It is driven by the master and received by the slave. Corresponds to the signal WS in the I2S-bus specification.
0x4 : LCD_VD_4
LCD data.
0x5 : LCD_VD_3
LCD data.
0x6 : LCD_VD_8
LCD data.
0x7 : LCD_VD_18
LCD data.
End of enumeration elements list.
I/O configuration register for pin P2[13]
address_offset : 0x134 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P2[13]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P2_13
General purpose digital input/output pin. This pin includes a 5 ns input glitch filter.
0x1 : EINT3
External interrupt 3 input.
0x2 : SD_DAT_3
Data line 3 for SD card interface.
0x3 : I2S_TX_SDA
Transmit data. It is driven by the transmitter and read by the receiver. Corresponds to the signal SD in the I2S-bus specification.
0x5 : LCD_VD_5
LCD data.
0x6 : LCD_VD_9
LCD data.
0x7 : LCD_VD_19
LCD data.
End of enumeration elements list.
I/O configuration register for pin P2[14]
address_offset : 0x138 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P2[14]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P2_14
General purpose digital input/output pin.
0x1 : EMC_CS2
LOW active Chip Select 2 signal.
0x2 : I2C1_SDA
I2C1 data input/output (this pin does not use a specialized I2C pad).
0x3 : T2_CAP0
Capture input for Timer 2, channel 0.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P2[15]
address_offset : 0x13C Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P2[15]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P2_15
General purpose digital input/output pin.
0x1 : EMC_CS3
LOW active Chip Select 3 signal.
0x2 : I2C1_SCL
I2C1 clock input/output (this pin does not use a specialized I2C pad).
0x3 : T2_CAP1
Capture input for Timer 2, channel 1.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P0[5]
address_offset : 0x14 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P0[5]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P0_5
General purpose digital input/output pin.
0x1 : I2S_RX_WS
I2S Receive word select. It is driven by the master and received by the slave. Corresponds to the signal WS in the I2S-bus specification.
0x2 : CAN_TD2
CAN2 transmitter output.
0x3 : T2_CAP1
Capture input for Timer 2, channel 1.
0x5 : CMP_RESET
Comparator reset.
0x7 : LCD_VD_1
LCD data.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P2[16]
address_offset : 0x140 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P2[16]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P2_16
General purpose digital input/output pin.
0x1 : EMC_CAS
LOW active SDRAM Column Address Strobe.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P2[17]
address_offset : 0x144 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P2[17]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P2_17
General purpose digital input/output pin.
0x1 : EMC_RAS
LOW active SDRAM Row Address Strobe.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P2[18]
address_offset : 0x148 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P2[18]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P2_18
General purpose digital input/output pin.
0x1 : EMC_CLK_0
SDRAM clock 0.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
ADMODE : Selects Analog/Digital mode.
bits : 7 - 14 (8 bit)
Enumeration: ENUM
0 : ANALOG_INPUT_MODE_
Analog input mode.
1 : DIGITAL_FUNCTIONAL_M
Digital functional mode.
End of enumeration elements list.
FILTR : Selects 10 ns input glitch filter.
bits : 8 - 16 (9 bit)
Enumeration: ENUM
0 : FILTER_DISABLED_
Filter disabled.
1 : FILTER_ENABLED_
Filter enabled.
End of enumeration elements list.
RESERVED : Reserved.
bits : 9 - 18 (10 bit)
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P2[19]
address_offset : 0x14C Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P2[19]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P2_19
General purpose digital input/output pin.
0x1 : EMC_CLK_1
SDRAM clock 1.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
ADMODE : Selects Analog/Digital mode.
bits : 7 - 14 (8 bit)
Enumeration: ENUM
0 : ANALOG_INPUT_MODE_
Analog input mode.
1 : DIGITAL_FUNCTIONAL_M
Digital functional mode.
End of enumeration elements list.
FILTR : Selects 10 ns input glitch filter.
bits : 8 - 16 (9 bit)
Enumeration: ENUM
0 : FILTER_DISABLED_
Filter disabled.
1 : FILTER_ENABLED_
Filter enabled.
End of enumeration elements list.
RESERVED : Reserved.
bits : 9 - 18 (10 bit)
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P2[20]
address_offset : 0x150 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P2[20]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P2_20
General purpose digital input/output pin.
0x1 : EMC_DYCS0
SDRAM chip select 0.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P2[21]
address_offset : 0x154 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P2[21]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P2_21
General purpose digital input/output pin.
0x1 : EMC_DYCS1
SDRAM chip select 1.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P2[22]
address_offset : 0x158 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P2[22]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P2_22
General purpose digital input/output pin.
0x1 : EMC_DYCS2
SDRAM chip select 2.
0x2 : SSP0_SCK
Serial clock for SSP0.
0x3 : T3_CAP0
Capture input for Timer 3, channel 0.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P2[23]
address_offset : 0x15C Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P2[23]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P2_23
General purpose digital input/output pin.
0x1 : EMC_DYCS3
SDRAM chip select 3.
0x2 : SSP0_SSEL
Slave Select for SSP0.
0x3 : T3_CAP1
Capture input for Timer 3, channel 1.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P2[24]
address_offset : 0x160 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P2[24]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P2_24
General purpose digital input/output pin.
0x1 : EMC_CKE0
SDRAM clock enable 0.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P2[25]
address_offset : 0x164 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P2[25]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P2_25
General purpose digital input/output pin.
0x1 : EMC_CKE1
SDRAM clock enable 1.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P2[26]
address_offset : 0x168 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P2[26]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P2_26
General purpose digital input/output pin.
0x1 : EMC_CKE2
SDRAM clock enable 2.
0x2 : SSP0_MISO
Master In Slave Out for SSP0.
0x3 : T3_MAT0
Match output for Timer 3, channel 0.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P2[27]
address_offset : 0x16C Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P2[27]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P2_27
General purpose digital input/output pin.
0x1 : EMC_CKE3
SDRAM clock enable 3.
0x2 : SSP0_MOSI
Master Out Slave In for SSP0.
0x3 : T3_MAT1
Match output for Timer 3, channel 1.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P2[28]
address_offset : 0x170 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P2[28]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P2_28
General purpose digital input/output pin.
0x1 : EMC_DQM0
Data mask 0 used with SDRAM and static devices.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P2[29]
address_offset : 0x174 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P2[29]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P2_29
General purpose digital input/output pin.
0x1 : EMC_DQM1
Data mask 1 used with SDRAM and static devices.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P2[30]
address_offset : 0x178 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P2[30]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P2_30
General purpose digital input/output pin.
0x1 : EMC_DQM2
Data mask 2 used with SDRAM and static devices.
0x2 : I2C2_SDA
I2C2 data input/output (this pin does not use a specialized I2C pad).
0x3 : T3_MAT2
Match output for Timer 3, channel 2.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P2[31]
address_offset : 0x17C Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P2[31]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P2_31
General purpose digital input/output pin.
0x1 : EMC_DQM3
Data mask 3 used with SDRAM and static devices.
0x2 : I2C2_SCL
I2C2 clock input/output (this pin does not use a specialized I2C pad).
0x3 : T3_MAT3
Match output for Timer 3, channel 3.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P0[6]
address_offset : 0x18 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P0[6]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P0_6
General purpose digital input/output pin.
0x1 : I2S_RX_SDA
I2S Receive data. It is driven by the transmitter and read by the receiver. Corresponds to the signal SD in the I2S-bus specification.
0x2 : SSP1_SSEL
Slave Select for SSP1.
0x3 : T2_MAT0
Match output for Timer 2, channel 0.
0x4 : U1_RTS
Request to Send output for UART1. Can also be configured to be an RS-485/EIA-485 output enable signal for UART1.
0x5 : CMP_ROSC
Comparator relaxation oscillator for 555 timer applications.
0x7 : LCD_VD_8
LCD data.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P3[0]
address_offset : 0x180 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P3[0]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P3_0
General purpose digital input/output pin.
0x1 : EMC_D_0
External memory data line 0.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P3[1]
address_offset : 0x184 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P3[1]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P3_1
General purpose digital input/output pin.
0x1 : EMC_D_1
External memory data line 1.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P3[2]
address_offset : 0x188 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P3[2]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P3_2
General purpose digital input/output pin.
0x1 : EMC_D_2
External memory data line 2.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P3[3]
address_offset : 0x18C Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P3[3]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P3_3
General purpose digital input/output pin.
0x1 : EMC_D_3
External memory data line 3.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P3[4]
address_offset : 0x190 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P3[4]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P3_4
General purpose digital input/output pin.
0x1 : EMC_D_4
External memory data line 4.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P3[5]
address_offset : 0x194 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P3[5]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P3_5
General purpose digital input/output pin.
0x1 : EMC_D_5
External memory data line 5.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P3[6]
address_offset : 0x198 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P3[6]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P3_6
General purpose digital input/output pin.
0x1 : EMC_D_6
External memory data line 6.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P3[7]
address_offset : 0x19C Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P3[7]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P3_7
General purpose digital input/output pin.
0x1 : EMC_D_7
External memory data line 7.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P3[8]
address_offset : 0x1A0 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P3[8]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P3_8
General purpose digital input/output pin.
0x1 : EMC_D_8
External memory data line 8.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P3[9]
address_offset : 0x1A4 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P3[9]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P3_9
General purpose digital input/output pin.
0x1 : EMC_D_9
External memory data line 9.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P3[10]
address_offset : 0x1A8 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P3[10]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P3_10
General purpose digital input/output pin.
0x1 : EMC_D_10
External memory data line 10.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P3[11]
address_offset : 0x1AC Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P3[11]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P3_11
General purpose digital input/output pin.
0x1 : EMC_D_11
External memory data line 11.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P3[12]
address_offset : 0x1B0 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P3[12]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P3_12
General purpose digital input/output pin.
0x1 : EMC_D_12
External memory data line 12.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P3[13]
address_offset : 0x1B4 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P3[13]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P3_13
General purpose digital input/output pin.
0x1 : EMC_D_13
External memory data line 13.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P3[14]
address_offset : 0x1B8 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P3[14]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P3_14
General purpose digital input/output pin.
0x1 : EMC_D_14
External memory data line 14.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P3[15]
address_offset : 0x1BC Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P3[15]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P3_15
General purpose digital input/output pin.
0x1 : EMC_D_15
External memory data line 15.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P0[7]
address_offset : 0x1C Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P0[7]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P0_7
General purpose digital input/output pin.
0x1 : I2S_TX_SCK
I2S transmit clock. It is driven by the master and received by the slave. Corresponds to the signal SCK in the I2S-bus specification.
0x2 : SSP1_SCK
Serial Clock for SSP1.
0x3 : T2_MAT1
Match output for Timer 2, channel 1.
0x4 : RTC_EV0
Event input 0 to Event Monitor/Recorder.
0x5 : CMP_VREF
Comparator reference voltage.
0x7 : LCD_VD_9
LCD data.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 14 (8 bit)
FILTER : Glitch filter control
bits : 8 - 16 (9 bit)
Enumeration: ENUM
0 : ENABLED
Noise pulses below approximately 10 ns are filtered out.
1 : DISABLED
No input filtering is done.
End of enumeration elements list.
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P3[16]
address_offset : 0x1C0 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P3[16]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P3_16
General purpose digital input/output pin.
0x1 : EMC_D_16
External memory data line 16.
0x2 : PWM0_1
Pulse Width Modulator 0, output 1.
0x3 : U1_TXD
Transmitter output for UART1.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P3[17]
address_offset : 0x1C4 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P3[17]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P3_17
General purpose digital input/output pin.
0x1 : EMC_D_17
External memory data line 17.
0x2 : PWM0_2
Pulse Width Modulator 0, output 2.
0x3 : U1_RXD
Receiver input for UART1.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P3[18]
address_offset : 0x1C8 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P3[18]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P3_18
General purpose digital input/output pin.
0x1 : EMC_D_18
External memory data line 18.
0x2 : PWM0_3
Pulse Width Modulator 0, output 3.
0x3 : U1_CTS
Clear to Send input for UART1.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P3[19]
address_offset : 0x1CC Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P3[19]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P3_19
General purpose digital input/output pin.
0x1 : EMC_D_19
External memory data line 19.
0x2 : PWM0_4
Pulse Width Modulator 0, output 4.
0x3 : U1_DCD
Data Carrier Detect input for UART1.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P3[20]
address_offset : 0x1D0 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P3[20]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P3_20
General purpose digital input/output pin.
0x1 : EMC_D_20
External memory data line 20.
0x2 : PWM0_5
Pulse Width Modulator 0, output 5.
0x3 : U1_DSR
Data Set Ready input for UART1.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P3[21]
address_offset : 0x1D4 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P3[21]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P3_21
General purpose digital input/output pin.
0x1 : EMC_D_21
External memory data line 21.
0x2 : PWM0_6
Pulse Width Modulator 0, output 6.
0x3 : U1_DTR
Data Terminal Ready output for UART1. Can also be configured to be an RS-485/EIA-485 output enable signal for UART1.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P3[22]
address_offset : 0x1D8 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P3[22]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P3_22
General purpose digital input/output pin.
0x1 : EMC_D_22
External memory data line 22.
0x2 : PWM0_CAP0
Capture input for PWM0, channel 0.
0x3 : U1_RI
Ring Indicator input for UART1.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P3[23]
address_offset : 0x1DC Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P3[23]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P3_23
General purpose digital input/output pin.
0x1 : EMC_D_23
External memory data line 23.
0x2 : PWM1_CAP0
Capture input for PWM1, channel 0.
0x3 : T0_CAP0
Capture input for Timer 0, channel 0.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P3[24]
address_offset : 0x1E0 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P3[24]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P3_24
General purpose digital input/output pin.
0x1 : EMC_D_24
External memory data line 24.
0x2 : PWM1_1
Pulse Width Modulator 1, output 1.
0x3 : T0_CAP1
Capture input for Timer 0, channel 1.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P3[25]
address_offset : 0x1E4 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P3[25]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P3_25
General purpose digital input/output pin.
0x1 : EMC_D_25
External memory data line 25.
0x2 : PWM1_2
Pulse Width Modulator 1, output 2.
0x3 : T0_MAT0
Match output for Timer 0, channel 0.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P3[26]
address_offset : 0x1E8 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P3[26]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P3_26
General purpose digital input/output pin.
0x1 : EMC_D_26
External memory data line 26.
0x2 : PWM1_3
Pulse Width Modulator 1, output 3.
0x3 : T0_MAT1
Match output for Timer 0, channel 1.
0x4 : STCLK
System tick timer clock input.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P3[27]
address_offset : 0x1EC Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P3[27]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P3_27
General purpose digital input/output pin.
0x1 : EMC_D_27
External memory data line 27.
0x2 : PWM1_4
Pulse Width Modulator 1, output 4.
0x3 : T1_CAP0
Capture input for Timer 1, channel 0.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P3[28]
address_offset : 0x1F0 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P3[28]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P3_28
General purpose digital input/output pin.
0x1 : EMC_D_28
External memory data line 28.
0x2 : PWM1_5
Pulse Width Modulator 1, output 5.
0x3 : T1_CAP1
Capture input for Timer 1, channel 1.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P3[29]
address_offset : 0x1F4 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P3[29]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P3_29
General purpose digital input/output pin.
0x1 : EMC_D_29
External memory data line 29.
0x2 : PWM1_6
Pulse Width Modulator 1, output 6.
0x3 : T1_MAT0
Match output for Timer 1, channel 0.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P3[30]
address_offset : 0x1F8 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P3[30]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P3_30
General purpose digital input/output pin.
0x1 : EMC_D_30
External memory data line 30.
0x2 : U1_RTS
Request to Send output for UART1. Can also be configured to be an RS-485/EIA-485 output enable signal for UART1.
0x3 : T1_MAT1
Match output for Timer 1, channel 1.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P3[31]
address_offset : 0x1FC Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P3[31]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P3_31
General purpose digital input/output pin.
0x1 : EMC_D_31
External memory data line 31.
0x3 : T1_MAT2
Match output for Timer 1, channel 2.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P0[8]
address_offset : 0x20 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P0[8]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P0_8
General purpose digital input/output pin.
0x1 : I2S_TX_WS
I2S Transmit word select. It is driven by the master and received by the slave. Corresponds to the signal WS in the I2S-bus specification.
0x2 : SSP1_MISO
Master In Slave Out for SSP1.
0x3 : T2_MAT2
Match output for Timer 2, channel 2.
0x4 : RTC_EV1
Event input 1 to Event Monitor/Recorder.
0x5 : CMP1_IN_3
Comparator 1, input 3.
0x7 : LCD_VD_16
LCD data.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 14 (8 bit)
FILTER : Glitch filter control
bits : 8 - 16 (9 bit)
Enumeration: ENUM
0 : ENABLED
Noise pulses below approximately 10 ns are filtered out.
1 : DISABLED
No input filtering is done.
End of enumeration elements list.
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P4[0]
address_offset : 0x200 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P4[0]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P4_0
General purpose digital input/output pin.
0x1 : EMC_A_0
External memory address line 0.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P4[1]
address_offset : 0x204 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P4[1]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P4_1
General purpose digital input/output pin.
0x1 : EMC_A_1
External memory address line 1.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P4[2]
address_offset : 0x208 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P4[2]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P4_2
General purpose digital input/output pin.
0x1 : EMC_A_2
External memory address line 2.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P4[3]
address_offset : 0x20C Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P4[3]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P4_3
General purpose digital input/output pin.
0x1 : EMC_A_3
External memory address line 3.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P4[4]
address_offset : 0x210 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P4[4]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P4_4
General purpose digital input/output pin.
0x1 : EMC_A_4
External memory address line 4.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P4[5]
address_offset : 0x214 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P4[5]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P4_5
General purpose digital input/output pin.
0x1 : EMC_A_5
External memory address line 5.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P4[6]
address_offset : 0x218 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P4[6]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P4_6
General purpose digital input/output pin.
0x1 : EMC_A_6
External memory address line 6.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P4[7]
address_offset : 0x21C Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P4[7]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P4_7
General purpose digital input/output pin.
0x1 : EMC_A_7
External memory address line 7.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P4[8]
address_offset : 0x220 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P4[8]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P4_8
General purpose digital input/output pin.
0x1 : EMC_A_8
External memory address line 8.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P4[9]
address_offset : 0x224 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P4[9]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P4_9
General purpose digital input/output pin.
0x1 : EMC_A_9
External memory address line 9.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P4[10]
address_offset : 0x228 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P4[10]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P4_10
General purpose digital input/output pin.
0x1 : EMC_A_10
External memory address line 10.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P4[11]
address_offset : 0x22C Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P4[11]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P4_11
General purpose digital input/output pin.
0x1 : EMC_A_11
External memory address line 11.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P4[12]
address_offset : 0x230 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P4[12]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P4_12
General purpose digital input/output pin.
0x1 : EMC_A_12
External memory address line 12.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P4[13]
address_offset : 0x234 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P4[13]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P4_13
General purpose digital input/output pin.
0x1 : EMC_A_13
External memory address line 13.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P4[14]
address_offset : 0x238 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P4[14]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P4_14
General purpose digital input/output pin.
0x1 : EMC_A_14
External memory address line 14.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P4[15]
address_offset : 0x23C Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P4[15]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P4_15
General purpose digital input/output pin.
0x1 : EMC_A_15
External memory address line 15.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P0[9]
address_offset : 0x24 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P0[9]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P0_9
General purpose digital input/output pin.
0x1 : I2S_TX_SDA
I2S transmit data. It is driven by the transmitter and read by the receiver. Corresponds to the signal SD in the I2S-bus specification.
0x2 : SSP1_MOSI
Master Out Slave In for SSP1.
0x3 : T2_MAT3
Match output for Timer 2, channel 3.
0x4 : RTC_EV2
Event input 2 to Event Monitor/Recorder.
0x5 : CMP1_IN_2
Comparator 1, input 2.
0x7 : LCD_VD_17
LCD data.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 14 (8 bit)
FILTER : Glitch filter control
bits : 8 - 16 (9 bit)
Enumeration: ENUM
0 : ENABLED
Noise pulses below approximately 10 ns are filtered out.
1 : DISABLED
No input filtering is done.
End of enumeration elements list.
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P4[16]
address_offset : 0x240 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P4[16]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P4_16
General purpose digital input/output pin.
0x1 : EMC_A_16
External memory address line 16.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P4[17]
address_offset : 0x244 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P4[17]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P4_17
General purpose digital input/output pin.
0x1 : EMC_A_17
External memory address line 17.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P4[18]
address_offset : 0x248 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P4[18]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P4_18
General purpose digital input/output pin.
0x1 : EMC_A_18
External memory address line 18.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P4[19]
address_offset : 0x24C Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P4[19]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P4_19
General purpose digital input/output pin.
0x1 : EMC_A_19
External memory address line 19.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P4[20]
address_offset : 0x250 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P4[20]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P4_20
General purpose digital input/output pin.
0x1 : EMC_A_20
External memory address line 20.
0x2 : I2C2_SDA
I2C2 data input/output (this pin does not use a specialized I2C pad).
0x3 : SSP1_SCK
Serial Clock for SSP1.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P4[21]
address_offset : 0x254 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P4[21]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P4_21
General purpose digital input/output pin.
0x1 : EMC_A_21
External memory address line 21.
0x2 : I2C2_SCL
I2C2 clock input/output (this pin does not use a specialized I2C pad).
0x3 : SSP1_SSEL
Slave Select for SSP1.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P4[22]
address_offset : 0x258 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P4[22]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P4_22
General purpose digital input/output pin.
0x1 : EMC_A_22
External memory address line 22.
0x2 : U2_TXD
Transmitter output for UART2.
0x3 : SSP1_MISO
Master In Slave Out for SSP1.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P4[23]
address_offset : 0x25C Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P4[23]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P4_23
General purpose digital input/output pin.
0x1 : EMC_A_23
External memory address line 23.
0x2 : U2_RXD
Receiver input for UART2.
0x3 : SSP1_MOSI
Master Out Slave In for SSP1.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P4[24]
address_offset : 0x260 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P4[24]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P4_24
General purpose digital input/output pin.
0x1 : EMC_OE
LOW active Output Enable signal.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P4[25]
address_offset : 0x264 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P4[25]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P4_25
General purpose digital input/output pin.
0x1 : EMC_WE
LOW active Write Enable signal.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P4[26]
address_offset : 0x268 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P4[26]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P4_26
General purpose digital input/output pin.
0x1 : EMC_BLS0
LOW active Byte Lane select signal 0.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P4[27]
address_offset : 0x26C Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P4[27]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P4_27
General purpose digital input/output pin.
0x1 : EMC_BLS1
LOW active Byte Lane select signal 1.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P4[28]
address_offset : 0x270 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P4[28]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P4_28
General purpose digital input/output pin.
0x1 : EMC_BLS2
LOW active Byte Lane select signal 2.
0x2 : U3_TXD
Transmitter output for UART3.
0x3 : T2_MAT0
Match output for Timer 2, channel 0.
0x5 : LCD_VD_6
LCD data.
0x6 : LCD_VD_10
LCD data.
0x7 : LCD_VD_2
LCD data.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P4[29]
address_offset : 0x274 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P4[29]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P4_29
General purpose digital input/output pin.
0x1 : EMC_BLS3
LOW active Byte Lane select signal 3.
0x2 : U3_RXD
Receiver input for UART3.
0x3 : T2_MAT1
Match output for Timer 2, channel 1.
0x4 : I2C2_SCL
I2C2 clock input/output (this pin does not use a specialized I2C pad).
0x5 : LCD_VD_7
LCD data.
0x6 : LCD_VD_11
LCD data.
0x7 : LCD_VD_3
LCD data.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P4[30]
address_offset : 0x278 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P4[30]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P4_30
General purpose digital input/output pin.
0x1 : EMC_CS0
LOW active Chip Select 0 signal.
0x5 : CMP0_OUT
Comparator 0, output.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P4[31]
address_offset : 0x27C Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P4[31]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P4_31
General purpose digital input/output pin.
0x1 : EMC_CS1
LOW active Chip Select 1 signal.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P0[10]
address_offset : 0x28 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P0[10]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P0_10
General purpose digital input/output pin.
0x1 : U2_TXD
Transmitter output for UART2.
0x2 : I2C2_SDA
I2C2 data input/output (this pin does not use a specialized I2C pad).
0x3 : T3_MAT0
Match output for Timer 3, channel 0.
0x7 : LCD_VD_5
LCD data.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P5[0]
address_offset : 0x280 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P5[0]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P5_0
General purpose digital input/output pin.
0x1 : EMC_A_24
External memory address line 24.
0x2 : SSP2_MOSI
Master Out Slave In for SSP2.
0x3 : T2_MAT2
Match output for Timer 2, channel 2.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P5[1]
address_offset : 0x284 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P5[1]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P5_1
General purpose digital input/output pin.
0x1 : EMC_A_25
External memory address line 25.
0x2 : SSP2_MISO
Master In Slave Out for SSP2.
0x3 : T2_MAT3
Match output for Timer 2, channel 3.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P5[2]
address_offset : 0x288 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P5[2]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P5_2
General purpose digital input/output pin.
0x3 : T3_MAT2
Match output for Timer 3, channel 2.
0x5 : I2C0_SDA
I2C0 data input/output (this pin uses a specialized I2C pad that supports I2C Fast Mode Plus).
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 14 (8 bit)
RESERVED : Reserved.
bits : 7 - 14 (8 bit)
HS : Configures I2C features for standard mode, fast mode, and Fast Mode Plus operation.
bits : 8 - 16 (9 bit)
Enumeration: ENUM
0 : ENABLED
I2C 50ns glitch filter and slew rate control enabled.
1 : DISABLED
I2C 50ns glitch filter and slew rate control disabled.
End of enumeration elements list.
HIDRIVE : Controls sink current capability of the pin, only for P5[2] and P5[3].
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : LOWDRIVE
Output drive sink is 4 mA. This is sufficient for standard and fast mode I2C.
1 : HIGHDRIVE
Output drive sink is 20 mA. This is needed for Fast Mode Plus I2C. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
RESERVED : Reserved.
bits : 10 - 41 (32 bit)
I/O configuration register for pin P5[3]
address_offset : 0x28C Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P5[3]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P5_3
General purpose digital input/output pin.
0x4 : U4_RXD
Receiver input for USART4.
0x5 : I2C0_SCL
I2C0 clock input/output (this pin uses a specialized I2C pad that supports I2C Fast Mode Plus.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 14 (8 bit)
RESERVED : Reserved.
bits : 7 - 14 (8 bit)
HS : Configures I2C features for standard mode, fast mode, and Fast Mode Plus operation.
bits : 8 - 16 (9 bit)
Enumeration: ENUM
0 : ENABLED
I2C 50ns glitch filter and slew rate control enabled.
1 : DISABLED
I2C 50ns glitch filter and slew rate control disabled.
End of enumeration elements list.
HIDRIVE : Controls sink current capability of the pin, only for P5[2] and P5[3].
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : LOWDRIVE
Output drive sink is 4 mA. This is sufficient for standard and fast mode I2C.
1 : HIGHDRIVE
Output drive sink is 20 mA. This is needed for Fast Mode Plus I2C. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
RESERVED : Reserved.
bits : 10 - 41 (32 bit)
I/O configuration register for pin P5[4]
address_offset : 0x290 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P5[4]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P5_4
General purpose digital input/output pin.
0x1 : U0_OE
RS-485/EIA-485 output enable signal for UART0.
0x3 : T3_MAT3
Match output for Timer 3, channel 3.
0x4 : U4_TXD
Transmitter output for USART4 (input/output in smart card mode).
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P0[11]
address_offset : 0x2C Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P0[11]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P0_11
General purpose digital input/output pin.
0x1 : U2_RXD
Receiver input for UART2.
0x2 : I2C2_SCL
I2C2 clock input/output (this pin does not use a specialized I2C pad).
0x3 : T3_MAT1
Match output for Timer 3, channel 1.
0x7 : LCD_VD_10
LCD data.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P0[12]
address_offset : 0x30 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P0[12]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P0_12
General purpose digital input/output pin.
0x1 : USB_PPWR2
Port Power enable signal for USB port 2.
0x2 : SSP1_MISO
Master In Slave Out for SSP1.
0x3 : ADC0_IN_6
A/D converter 0, input 6. When configured as an ADC input, the digital function of the pin must be disabled.
End of enumeration elements list.
I/O configuration register for pin P0[13]
address_offset : 0x34 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P0[13]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P0_13
General purpose digital input/output pin.
0x1 : USB_UP_LED2
USB port 2 GoodLink LED indicator. It is LOW when the device is configured (non-control endpoints enabled), or when the host is enabled and has detected a device on the bus. It is HIGH when the device is not configured, or when host is enabled and has not detected a device on the bus, or during global suspend. It transitions between LOW and HIGH (flashes) when the host is enabled and detects activity on the bus.
0x2 : SSP1_MOSI
Master Out Slave In for SSP1.
0x3 : ADC0_IN_7
A/D converter 0, input 7. When configured as an ADC input, the digital function of the pin must be disabled.
End of enumeration elements list.
I/O configuration register for pin P0[14]
address_offset : 0x38 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P0[14]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P0_14
General purpose digital input/output pin.
0x1 : USB_HSTEN2
Host Enabled status for USB port 2.
0x2 : SSP1_SSEL
Slave Select for SSP1.
0x3 : USB_CONNECT2
SoftConnect control for USB port 2. Signal used to switch an external 1.5 kW resistor under software control. Used with the SoftConnect USB feature.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P0[15]
address_offset : 0x3C Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P0[15]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P0_15
General purpose digital input/output pin.
0x1 : U1_TXD
Transmitter output for UART1.
0x2 : SSP0_SCK
Serial clock for SSP0.
0x5 : SPIFI_IO_2
Data bit 0 for SPIFI.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P0[1]
address_offset : 0x4 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P0[1]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P0_1
General purpose digital input/output pin.
0x1 : CAN_TD1
CAN1 transmitter output.
0x2 : U3_RXD
Receiver input for UART3.
0x3 : I2C1_SCL
I2C1 clock input/output (this pin does not use a specialized I2C pad).
0x4 : U0_RXD
Receiver input for UART0.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P0[16]
address_offset : 0x40 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P0[16]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P0_16
General purpose digital input/output pin.
0x1 : U1_RXD
Receiver input for UART1.
0x2 : SSP0_SSEL
Slave Select for SSP0.
0x5 : SPIFI_IO_3
Data bit 0 for SPIFI.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P0[17]
address_offset : 0x44 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P0[17]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P0_17
General purpose digital input/output pin.
0x1 : U1_CTS
Clear to Send input for UART1.
0x2 : SSP0_MISO
Master In Slave Out for SSP0.
0x5 : SPIFI_IO_1
Data bit 0 for SPIFI.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P0[18]
address_offset : 0x48 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P0[18]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P0_18
General purpose digital input/output pin.
0x1 : U1_DCD
Data Carrier Detect input for UART1.
0x2 : SSP0_MOSI
Master Out Slave In for SSP0.
0x5 : SPIFI_IO_0
Data bit 0 for SPIFI.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P0[19]
address_offset : 0x4C Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P0[19]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P0_19
General purpose digital input/output pin.
0x1 : U1_DSR
Data Set Ready input for UART1.
0x2 : SD_CLK
Clock output line for SD card interface.
0x3 : I2C1_SDA
I2C1 data input/output (this pin does not use a specialized I2C pad).
0x7 : LCD_VD_13
LCD data.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P0[20]
address_offset : 0x50 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P0[20]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P0_20
General purpose digital input/output pin.
0x1 : U1_DTR
Data Terminal Ready output for UART1. Can also be configured to be an RS-485/EIA-485 output enable signal for UART1.
0x2 : SD_CMD
Command line for SD card interface.
0x3 : I2C1_SCL
I2C1 clock input/output (this pin does not use a specialized I2C pad).
0x7 : LCD_VD_14
LCD data.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P0[21]
address_offset : 0x54 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P0[21]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P0_21
General purpose digital input/output pin.
0x1 : U1_RI
Ring Indicator input for UART1.
0x2 : SD_PWR
Power Supply Enable for external SD card power supply.
0x3 : U4_OE
RS-485/EIA-485 output enable signal for UART4.
0x4 : CAN_RD1
CAN1 receiver input.
0x5 : U4_SCLK
USART 4 clock input or output in synchronous mode.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P0[22]
address_offset : 0x58 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P0[22]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P0_22
General purpose digital input/output pin.
0x1 : U1_RTS
Request to Send output for UART1. Can also be configured to be an RS-485/EIA-485 output enable signal for UART1.
0x2 : SD_DAT_0
Data line 0 for SD card interface.
0x3 : U4_TXD
Transmitter output for USART4 (input/output in smart card mode).
0x4 : CAN_TD1
CAN1 transmitter output.
0x5 : SPIFI_CLK
Clock output for SPIFI.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
ADMODE : Selects Analog/Digital mode.
bits : 7 - 14 (8 bit)
Enumeration: ENUM
0 : ANALOG_INPUT_MODE_
Analog input mode.
1 : DIGITAL_FUNCTIONAL_M
Digital functional mode.
End of enumeration elements list.
FILTR : Selects 10 ns input glitch filter.
bits : 8 - 16 (9 bit)
Enumeration: ENUM
0 : FILTER_DISABLED_
Filter disabled.
1 : FILTER_ENABLED_
Filter enabled.
End of enumeration elements list.
RESERVED : Reserved.
bits : 9 - 18 (10 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P0[23]
address_offset : 0x5C Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P0[23]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P0_23
General purpose digital input/output pin.
0x1 : ADC0_IN_0
A/D converter 0, input 0. When configured as an ADC input, the digital function of the pin must be disabled.
0x2 : I2S_RX_SCK
Receive Clock. It is driven by the master and received by the slave. Corresponds to the signal SCK in the I2S-bus specification.
0x3 : T3_CAP0
Capture input for Timer 3, channel 0.
End of enumeration elements list.
I/O configuration register for pin P0[24]
address_offset : 0x60 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P0[24]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P0_24
General purpose digital input/output pin.
0x1 : ADC0_IN_1
A/D converter 0, input 1. When configured as an ADC input, the digital function of the pin must be disabled.
0x2 : I2S_RX_WS
Receive Word Select. It is driven by the master and received by the slave. Corresponds to the signal WS in the I2S-bus specification.
0x3 : T3_CAP1
Capture input for Timer 3, channel 1.
End of enumeration elements list.
I/O configuration register for pin P0[25]
address_offset : 0x64 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P0[25]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P0_25
General purpose digital input/output pin.
0x1 : ADC0_IN_2
A/D converter 0, input 2. When configured as an ADC input, the digital function of the pin must be disabled.
0x2 : I2S_RX_SDA
Receive data. It is driven by the transmitter and read by the receiver. Corresponds to the signal SD in the I2S-bus specification.
0x3 : U3_TXD
Transmitter output for UART3.
End of enumeration elements list.
I/O configuration register for pin P0[26]
address_offset : 0x68 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P0[26]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P0_26
General purpose digital input/output pin.
0x1 : ADC0_IN_3
A/D converter 0, input 3. When configured as an ADC input, the digital function of the pin must be disabled.
0x2 : DAC_OUT
D/A converter output. When configured as the DAC output, the digital function of the pin must be disabled.
0x3 : U3_RXD
Receiver input for UART3.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
ADMODE : Selects Analog/Digital mode.
bits : 7 - 14 (8 bit)
Enumeration: ENUM
0 : ANALOG_INPUT_MODE_
Analog input mode.
1 : DIGITAL_FUNCTIONAL_M
Digital functional mode.
End of enumeration elements list.
FILTR : Selects 10 ns input glitch filter.
bits : 8 - 16 (9 bit)
Enumeration: ENUM
0 : FILTER_DISABLED_
Filter disabled.
1 : FILTER_ENABLED_
Filter enabled.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 26 (16 bit)
RESERVED : Reserved.
bits : 11 - 26 (16 bit)
DACEN : DAC output enable.
bits : 16 - 32 (17 bit)
Enumeration: ENUM
0 : DISABLE
DAC disable.
1 : ENABLE
DAC enable.
End of enumeration elements list.
RESERVED : Reserved.
bits : 17 - 48 (32 bit)
I/O configuration register for pin P0[27]
address_offset : 0x6C Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P0[27]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P0_27
General purpose digital input/output pin.
0x1 : I2C0_SDA
I2C0 data input/output. (This pin uses a specialized I2C pad).
0x2 : USB_SDA1
I2C serial data for communication with an external USB transceiver.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 14 (8 bit)
RESERVED : Reserved.
bits : 7 - 14 (8 bit)
HS : Configures I2C features for standard mode, fast mode, and Fast Mode Plus operation.
bits : 8 - 16 (9 bit)
Enumeration: ENUM
0 : ENABLED
I2C 50ns glitch filter and slew rate control enabled.
1 : DISABLED
I2C 50ns glitch filter and slew rate control disabled.
End of enumeration elements list.
HIDRIVE : Controls sink current capability of the pin, only for P5[2] and P5[3].
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : LOWDRIVE
Output drive sink is 4 mA. This is sufficient for standard and fast mode I2C.
1 : HIGHDRIVE
Output drive sink is 20 mA. This is needed for Fast Mode Plus I2C. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
RESERVED : Reserved.
bits : 10 - 41 (32 bit)
I/O configuration register for pin P0[28]
address_offset : 0x70 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P0[28]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P0_28
General purpose digital input/output pin.
0x1 : I2C0_SCL
I2C0 clock input/output (this pin uses a specialized I2C pad.
0x2 : USB_SCL1
I2C serial clock for communication with an external USB transceiver.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 14 (8 bit)
RESERVED : Reserved.
bits : 7 - 14 (8 bit)
HS : Configures I2C features for standard mode, fast mode, and Fast Mode Plus operation.
bits : 8 - 16 (9 bit)
Enumeration: ENUM
0 : ENABLED
I2C 50ns glitch filter and slew rate control enabled.
1 : DISABLED
I2C 50ns glitch filter and slew rate control disabled.
End of enumeration elements list.
HIDRIVE : Controls sink current capability of the pin, only for P5[2] and P5[3].
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : LOWDRIVE
Output drive sink is 4 mA. This is sufficient for standard and fast mode I2C.
1 : HIGHDRIVE
Output drive sink is 20 mA. This is needed for Fast Mode Plus I2C. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
RESERVED : Reserved.
bits : 10 - 41 (32 bit)
I/O configuration register for pin P0[29]
address_offset : 0x74 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P0[29]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P0_29
General purpose digital input/output pin.
0x1 : USB_DP1
USB port 1 bidirectional D+ line.
0x2 : EINT0
External interrupt 0 input.
End of enumeration elements list.
RESERVED : Reserved.
bits : 3 - 34 (32 bit)
I/O configuration register for pin P0[30]
address_offset : 0x78 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P0[30]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P0_30
General purpose digital input/output pin.
0x1 : USB_DM1
USB port 1 bidirectional D- line.
0x2 : EINT1
External interrupt 1 input.
End of enumeration elements list.
RESERVED : Reserved.
bits : 3 - 34 (32 bit)
I/O configuration register for pin P0[31]
address_offset : 0x7C Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P0[31]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P0_31
General purpose digital input/output pin.
0x1 : USB_DP2
USB port 2 bidirectional D+ line.
End of enumeration elements list.
RESERVED : Reserved.
bits : 3 - 34 (32 bit)
I/O configuration register for pin P0[2]
address_offset : 0x8 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P0[2]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P0_2
General purpose digital input/output pin.
0x1 : U0_TXD
Transmitter output for UART0.
0x2 : U3_TXD
Transmitter output for UART3.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P1[0]
address_offset : 0x80 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P1[0]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P1_0
General purpose digital input/output pin.
0x1 : ENET_TXD0
Ethernet transmit data 0 (RMII/MII interface).
0x3 : T3_CAP1
Capture input for Timer 3, channel 1.
0x4 : SSP2_SCK
Serial clock for SSP2.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P1[1]
address_offset : 0x84 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P1[1]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P1_1
General purpose digital input/output pin.
0x1 : ENET_TXD1
Ethernet transmit data 1 (RMII/MII interface).
0x3 : T3_MAT3
Match output for Timer 3, channel 3.
0x4 : SSP2_MOSI
Master Out Slave In for SSP2.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P1[2]
address_offset : 0x88 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P1[2]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P1_2
General purpose digital input/output pin.
0x1 : ENET_TXD2
Ethernet transmit data 2 (MII interface).
0x2 : SD_CLK
Clock output line for SD card interface.
0x3 : PWM0_1
Pulse Width Modulator 0, output 1.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P1[3]
address_offset : 0x8C Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P1[3]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P1_3
General purpose digital input/output pin.
0x1 : ENET_TXD3
Ethernet transmit data 3 (MII interface).
0x2 : SD_CMD
Command line for SD card interface.
0x3 : PWM0_2
Pulse Width Modulator 0, output 2.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P1[4]
address_offset : 0x90 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P1[4]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P1_4
General purpose digital input/output pin.
0x1 : ENET_TX_EN
Ethernet transmit data enable (RMII/MII interface).
0x3 : T3_MAT2
Match output for Timer 3, channel 2.
0x4 : SSP2_MISO
Master In Slave Out for SSP2.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P1[5]
address_offset : 0x94 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P1[5]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P1_5
General purpose digital input/output pin.
0x1 : ENET_TX_ER
Ethernet Transmit Error (MII interface).
0x2 : SD_PWR
Power Supply Enable for external SD card power supply.
0x3 : PWM0_3
Pulse Width Modulator 0, output 3.
0x5 : CMP1_IN_1
Comparator 1, input 1.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P1[6]
address_offset : 0x98 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P1[6]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P1_6
General purpose digital input/output pin.
0x1 : ENET_TX_CLK
Ethernet Transmit Clock (MII interface).
0x2 : SD_DAT_0
Data line 0 for SD card interface.
0x3 : PWM0_4
Pulse Width Modulator 0, output 4.
0x5 : CMP0_IN_3
Comparator 0, input 3.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P1[7]
address_offset : 0x9C Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P1[7]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P1_7
General purpose digital input/output pin.
0x1 : ENET_COL
Ethernet Collision detect (MII interface).
0x2 : SD_DAT_1
Data line 1 for SD card interface.
0x3 : PWM0_5
Pulse Width Modulator 0, output 5.
0x5 : CMP1_IN_0
Comparator 1, input 0.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P1[8]
address_offset : 0xA0 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P1[8]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P1_8
General purpose digital input/output pin.
0x1 : ENET_CRS_CRS_DV
Ethernet Carrier Sense (MII interface) or Ethernet Carrier Sense/Data Valid (RMII interface).
0x3 : T3_MAT1
Match output for Timer 3, channel 1.
0x4 : SSP2_SSEL
Slave Select for SSP2.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P1[9]
address_offset : 0xA4 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P1[9]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P1_9
General purpose digital input/output pin.
0x1 : ENET_RXD0
Ethernet receive data 0 (RMII/MII interface).
0x3 : T3_MAT0
Match output for Timer 3, channel 0.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P1[10]
address_offset : 0xA8 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P1[10]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P1_10
General purpose digital input/output pin.
0x1 : ENET_RXD1
Ethernet receive data 1 (RMII/MII interface).
0x3 : T3_CAP0
Capture input for Timer 3, channel 0.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P1[11]
address_offset : 0xAC Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P1[11]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P1_11
General purpose digital input/output pin.
0x1 : ENET_RXD2
Ethernet Receive Data 2 (MII interface).
0x2 : SD_DAT_2
Data line 2 for SD card interface.
0x3 : PWM0_6
Pulse Width Modulator 0, output 6.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P1[12]
address_offset : 0xB0 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P1[12]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P1_12
General purpose digital input/output pin.
0x1 : ENET_RXD3
Ethernet Receive Data (MII interface).
0x2 : SD_DAT_3
Data line 3 for SD card interface.
0x3 : PWM0_CAP0
Capture input for PWM0, channel 0.
0x5 : CMP1_OUT
Comparator 1, output.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P1[13]
address_offset : 0xB4 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P1[13]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P1_13
General purpose digital input/output pin.
0x1 : ENET_RX_DV
Ethernet Receive Data Valid (MII interface).
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P1[14]
address_offset : 0xB8 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P1[14]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P1_14
General purpose digital input/output pin.
0x1 : ENET_RX_ER
Ethernet receive error (RMII/MII interface).
0x3 : T2_CAP0
Capture input for Timer 2, channel 0.
0x5 : CMP0_IN_0
Comparator 0, input 0.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P1[15]
address_offset : 0xBC Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P1[15]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P1_15
General purpose digital input/output pin.
0x1 : ENET_RX_CLK_REF_CLK
Ethernet Receive Clock (MII interface) or Ethernet Reference Clock (RMII interface).
0x3 : I2C2_SDA
I2C2 data input/output (this pin does not use a specialized I2C pad).
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P0[3]
address_offset : 0xC Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P0[3]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P0_3
General purpose digital input/output pin.
0x1 : U0_RXD
Receiver input for UART0.
0x2 : U3_RXD
Receiver input for UART3.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P1[16]
address_offset : 0xC0 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P1[16]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P1_16
General purpose digital input/output pin.
0x1 : ENET_MDC
Ethernet MIIM clock.
0x2 : I2S_TX_MCLK
I2S transmit master clock.
0x5 : CMP0_IN_1
Comparator 0, input 1.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P1[17]
address_offset : 0xC4 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P1[17]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P1_17
General purpose digital input/output pin.
0x1 : ENET_MDIO
Ethernet MIIM data input and output.
0x2 : I2S_RX_MCLK
I2S receive master clock.
0x5 : CMP0_IN_2
Comparator 0, input 2.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P1[18]
address_offset : 0xC8 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P1[18]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P1_18
General purpose digital input/output pin.
0x1 : USB_UP_LED1
It is LOW when the device is configured (non-control endpoints enabled), or when the host is enabled and has detected a device on the bus. It is HIGH when the device is not configured, or when host is enabled and has not detected a device on the bus, or during global suspend. It transitions between LOW and HIGH (flashes) when the host is enabled and detects activity on the bus.
0x2 : PWM1_1
Pulse Width Modulator 1, channel 1 output.
0x3 : T1_CAP0
Capture input for Timer 1, channel 0.
0x5 : SSP1_MISO
Master In Slave Out for SSP1.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P1[19]
address_offset : 0xCC Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P1[19]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P1_19
General purpose digital input/output pin.
0x1 : USB_TX_E1
Transmit Enable signal for USB port 1 (OTG transceiver).
0x2 : USB_PPWR1
Port Power enable signal for USB port 1.
0x3 : T1_CAP1
Capture input for Timer 1, channel 1.
0x4 : MC_0A
Motor control PWM channel 0, output A.
0x5 : SSP1_SCK
Serial clock for SSP1.
0x6 : U2_OE
RS-485/EIA-485 output enable signal for UART2.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P1[20]
address_offset : 0xD0 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P1[20]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P1_20
General purpose digital input/output pin.
0x1 : USB_TX_DP1
D+ transmit data for USB port 1 (OTG transceiver).
0x2 : PWM1_2
Pulse Width Modulator 1, channel 2 output.
0x3 : QEI_PHA
Quadrature Encoder Interface PHA input.
0x4 : MC_FB0
Motor control PWM channel 0 feedback input.
0x5 : SSP0_SCK
Serial clock for SSP0.
0x6 : LCD_VD_6
LCD data.
0x7 : LCD_VD_10
LCD data.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P1[21]
address_offset : 0xD4 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P1[21]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P1_21
General purpose digital input/output pin.
0x1 : USB_TX_DM1
D- transmit data for USB port 1 (OTG transceiver).
0x2 : PWM1_3
Pulse Width Modulator 1, channel 3 output.
0x3 : SSP0_SSEL
Slave Select for SSP0.
0x4 : MC_ABORT
Motor control PWM, active low fast abort.
0x6 : LCD_VD_7
LCD data.
0x7 : LCD_VD_11
LCD data.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P1[22]
address_offset : 0xD8 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P1[22]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P1_22
General purpose digital input/output pin.
0x1 : USB_RCV1
Differential receive data for USB port 1 (OTG transceiver).
0x2 : USB_PWRD1
Power Status for USB port 1 (host power switch).
0x3 : T1_MAT0
Match output for Timer 1, channel 0.
0x4 : MC_0B
Motor control PWM channel 0, output B.
0x5 : SSP1_MOSI
Master Out Slave In for SSP1.
0x6 : LCD_VD_8
LCD data.
0x7 : LCD_VD_12
LCD data.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P1[23]
address_offset : 0xDC Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P1[23]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P1_23
General purpose digital input/output pin.
0x1 : USB_RX_DP1
D+ receive data for USB port 1 (OTG transceiver).
0x2 : PWM1_4
Pulse Width Modulator 1, channel 4 output.
0x3 : QEI_PHB
Quadrature Encoder Interface PHB input.
0x4 : MC_FB1
Motor control PWM channel 1 feedback input.
0x5 : SSP0_MISO
Master In Slave Out for SSP0.
0x6 : LCD_VD_9
LCD data.
0x7 : LCD_VD_13
LCD data.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P1[24]
address_offset : 0xE0 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P1[24]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P1_24
General purpose digital input/output pin.
0x1 : USB_RX_DM1
D- receive data for USB port 1 (OTG transceiver).
0x2 : PWM1_5
Pulse Width Modulator 1, channel 5 output.
0x3 : QEI_IDX
Quadrature Encoder Interface INDEX input.
0x4 : MC_FB2
Motor control PWM channel 2 feedback input.
0x5 : SSP0_MOSI
Master Out Slave in for SSP0.
0x6 : LCD_VD_10
LCD data.
0x7 : LCD_VD_14
LCD data.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P1[25]
address_offset : 0xE4 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P1[25]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P1_25
General purpose digital input/output pin.
0x1 : USB_LS1
Low Speed status for USB port 1 (OTG transceiver).
0x2 : USB_HSTEN1
Host Enabled status for USB port 1.
0x3 : T1_MAT1
Match output for Timer 1, channel 1.
0x4 : MC_1A
Motor control PWM channel 1, output A.
0x5 : CLKOUT
Selectable clock output.
0x6 : LCD_VD_11
LCD data.
0x7 : LCD_VD_15
LCD data.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P1[26]
address_offset : 0xE8 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P1[26]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P1_26
General purpose digital input/output pin.
0x1 : USB_SSPND1
USB port 1 Bus Suspend status (OTG transceiver).
0x2 : PWM1_6
Pulse Width Modulator 1, channel 6 output.
0x3 : T0_CAP0
Capture input for Timer 0, channel 0.
0x4 : MC_1B
Motor control PWM channel 1, output B.
0x5 : SSP1_SSEL
Slave Select for SSP1.
0x6 : LCD_VD_12
LCD data.
0x7 : LCD_VD_20
LCD data.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P1[27]
address_offset : 0xEC Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P1[27]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P1_27
General purpose digital input/output pin.
0x1 : USB_INT1
USB port 1 OTG transceiver interrupt (OTG transceiver).
0x2 : USB_OVRCR1
USB port 1 Over-Current status.
0x3 : T0_CAP1
Capture input for Timer 0, channel 1.
0x4 : CLKOUT
Selectable clock output.
0x6 : LCD_VD_13
LCD data.
0x7 : LCD_VD_21
LCD data.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P1[28]
address_offset : 0xF0 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P1[28]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P1_28
General purpose digital input/output pin.
0x1 : USB_SCL1
USB port 1 I2C serial clock (OTG transceiver).
0x2 : PWM1_CAP0
Capture input for PWM1, channel 0.
0x3 : T0_MAT0
Match output for Timer 0, channel 0.
0x4 : MC_2A
Motor control PWM channel 2, output A.
0x5 : SSP0_SSEL
Slave Select for SSP0.
0x6 : LCD_VD_14
LCD data.
0x7 : LCD_VD_22
LCD data.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P1[29]
address_offset : 0xF4 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P1[29]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P1_29
General purpose digital input/output pin.
0x1 : USB_SDA1
USB port 1 I2C serial data (OTG transceiver).
0x2 : PWM1_CAP1
Capture input for PWM1, channel 1.
0x3 : T0_MAT1
Match output for Timer 0, channel 1.
0x4 : MC_2B
Motor control PWM channel 2, output B.
0x5 : U4_TXD
Transmitter output for USART4 (input/output in smart card mode).
0x6 : LCD_VD_15
LCD data.
0x7 : LCD_VD_23
LCD data.
End of enumeration elements list.
MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 3 - 7 (5 bit)
Enumeration: ENUM
0x0 : INACTIVE_NO_PULL_DO
Inactive (no pull-down/pull-up resistor enabled).
0x1 : PULL_DOWN_RESISTOR_E
Pull-down resistor enabled.
0x2 : PULL_UP_RESISTOR_ENA
Pull-up resistor enabled.
0x3 : REPEATER_MODE_
Repeater mode.
End of enumeration elements list.
HYS : Hysteresis.
bits : 5 - 10 (6 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : ENABLE_
Enable.
End of enumeration elements list.
INV : Invert input
bits : 6 - 12 (7 bit)
Enumeration: ENUM
0 : INPUT_NOT_INVERTED_
Input not inverted (HIGH on pin reads as 1, LOW on pin reads as 0).
1 : INPUT_INVERTED_HIGH
Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1).
End of enumeration elements list.
RESERVED : Reserved.
bits : 7 - 15 (9 bit)
SLEW : Driver slew rate
bits : 9 - 18 (10 bit)
Enumeration: ENUM
0 : STANDARD
Standard mode, output slew rate control is enabled. More outputs can be switched simultaneously.
1 : FAST
Fast mode, slew rate control is disabled. Refer to the appropriate specific device data sheet for details.
End of enumeration elements list.
OD : Open-drain mode.
bits : 10 - 20 (11 bit)
Enumeration: ENUM
0 : DISABLE_
Disable.
1 : OPEN_DRAIN_MODE_ENAB
Open-drain mode enabled. This is not a true open-drain mode. Input cannot be pulled up above VDD.
End of enumeration elements list.
RESERVED : Reserved.
bits : 11 - 42 (32 bit)
I/O configuration register for pin P1[30]
address_offset : 0xF8 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P1[30]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P1_30
General purpose digital input/output pin.
0x1 : USB_PWRD2
Power Status for USB port 2.
0x2 : USB_VBUS
Monitors the presence of USB bus power.This signal must be HIGH for USB reset to occur.
0x3 : ADC0_IN_4
A/D converter 0, input 4. When configured as an ADC input, the digital function of the pin must be disabled.
0x4 : I2C0_SDA
I2C0 data input/output (this pin does not use a specialized I2C pad.
0x5 : U3_OE
RS-485/EIA-485 output enable signal for UART3.
End of enumeration elements list.
I/O configuration register for pin P1[31]
address_offset : 0xFC Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FUNC : Selects pin function for pin P1[31]
bits : 0 - 2 (3 bit)
Enumeration: ENUM
0x0 : P1_31
General purpose digital input/output pin.
0x1 : USB_OVRCR2
Over-Current status for USB port 2.
0x2 : SSP1_SCK
Serial Clock for SSP1.
0x3 : ADC0_IN_5
A/D converter 0, input 5. When configured as an ADC input, the digital function of the pin must be disabled.
0x4 : I2C0_SCL
I2C0 clock input/output (this pin does not use a specialized I2C pad.
End of enumeration elements list.
Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !
This website is sponsored by Embeetle, an IDE designed from scratch for embedded software developers.