\n
address_offset : 0x0 Bytes (0x0)
size : 0xFFC byte (0x0)
mem_usage : registers
protection : not protected
Module Control
address_offset : 0x0 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
SAEN : Stand-Alone Mode Enable.
bits : 0 - 0 (1 bit)
Enumeration:
0 : DISABLED
Use the external regulator in normal mode.
1 : ENABLED
Use the external regulator in stand-alone mode.
End of enumeration elements list.
WPULLEN : Weak Pull Up/Down Enable.
bits : 24 - 24 (1 bit)
Enumeration:
0 : DISABLED
Disable the external regulator weak pull-up/down resistor on the EXREGBD pin and weak pull-down resistor on the EXREGOUT pin.
1 : ENABLED
Enable the external regulator weak pull-up/down resistor on the EXREGBD pin and weak pull-down resistor on the EXREGOUT pin.
End of enumeration elements list.
FBLEN : Foldback Limiting Enable.
bits : 25 - 25 (1 bit)
Enumeration:
0 : DISABLED
Disable foldback limiting.
1 : ENABLED
Enable foldback limiting.
End of enumeration elements list.
PNSEL : NPN/PNP Type Select.
bits : 26 - 26 (1 bit)
Enumeration:
0 : NPN
Select NPN Mode.
1 : PNP
Select PNP Mode.
End of enumeration elements list.
FBPINSEL : Foldback Sensing Pin Select.
bits : 27 - 27 (1 bit)
Enumeration:
0 : EXREGSN
Use the input to the EXREGSN pin for foldback limiting.
1 : VREGIN
Use the input to the VREGIN pin for foldback limiting.
End of enumeration elements list.
EVREGEN : External Regulator Enable.
bits : 31 - 31 (1 bit)
Enumeration:
0 : DISABLED
Disable the external regulator.
1 : ENABLED
Enable the external regulator.
End of enumeration elements list.
Module Configuration
address_offset : 0x10 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
IMINFINE : Minimum Current Fine Select.
bits : 0 - 1 (2 bit)
Enumeration:
0 : 0_UA
Minimum current limit is IMIN current + 0 uA.
1 : 0P25_UA
Minimum current limit is IMIN current + 0.25 uA.
2 : 0P5_UA
Minimum current limit is IMIN current + 0.50 uA.
3 : 0P75_UA
Minimum current limit is IMIN current + 0.75 uA.
End of enumeration elements list.
IMIN : Minimum Current Select.
bits : 2 - 4 (3 bit)
Enumeration:
0 : 1_UA
Minimum current limit is 1 uA + IMINFINE current.
1 : 2_UA
Minimum current limit is 2 uA + IMINFINE current.
2 : 3_UA
Minimum current limit is 3 uA + IMINFINE current.
3 : 4_UA
Minimum current limit is 4 uA + IMINFINE current.
4 : 5_UA
Minimum current limit is 5 uA + IMINFINE current.
5 : 6_UA
Minimum current limit is 6 uA + IMINFINE current.
6 : 7_UA
Minimum current limit is 7 uA + IMINFINE current.
7 : 8_UA
Minimum current limit is 8 uA + IMINFINE current.
End of enumeration elements list.
FBVOSEL : Foldback Voltage Offset Select.
bits : 8 - 10 (3 bit)
Enumeration:
0 : 0_V
Foldback voltage offset is 0 V.
1 : 0P5_V
Foldback voltage offset is 0.5 V.
2 : 1_V
Foldback voltage offset is 1 V.
3 : 1P5_V
Foldback voltage offset is 1.5 V.
4 : 2_V
Foldback voltage offset is 2 V.
5 : 2P5_V
Foldback voltage offset is 2.5 V.
6 : 3_V
Foldback voltage offset is 3 V.
7 : 3P5_V
Foldback voltage offset is 3.5 V.
End of enumeration elements list.
FBRATE : Voltage Sense Gain Multiplier.
bits : 12 - 14 (3 bit)
Enumeration:
0 : 4_UA_PER_V
Set the foldback rate to 4 uA/V.
1 : 2_UA_PER_V
Set the foldback rate to 2 uA/V.
2 : 1_UA_PER_V
Set the foldback rate to 1 uA/V.
3 : 0P5_UA_PER_V
Set the foldback rate to 0.5 uA/V.
5 : 8_UA_PER_V
Set the foldback rate to 8 uA/V.
6 : 16_UA_PER_V
Set the foldback rate to 16 uA/V.
7 : 32_UA_PER_V
Set the foldback rate to 32 uA/V.
End of enumeration elements list.
IMAX : Maximum Current Select.
bits : 16 - 18 (3 bit)
Enumeration:
0 : 2_UA
Maximum current limit is 2 uA.
1 : 3_UA
Maximum current limit is 3 uA.
2 : 4_UA
Maximum current limit is 4 uA.
3 : 5_UA
Maximum current limit is 5 uA.
4 : 6_UA
Maximum current limit is 6 uA.
5 : 7_UA
Maximum current limit is 7 uA.
6 : 8_UA
Maximum current limit is 8 uA.
7 : 9_UA
Maximum current limit is 9 uA.
End of enumeration elements list.
VOUTSEL : Regulator Output Voltage Select.
bits : 24 - 29 (6 bit)
Module Status
address_offset : 0x20 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FBMAXF : Maximum Foldback Flag.
bits : 0 - 0 (1 bit)
access : read-only
Enumeration:
0 : NOT_SET
Maximum foldback has not been reached.
1 : SET
Maximum foldback has been reached.
End of enumeration elements list.
Current Sense Control
address_offset : 0x40 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
ISNSEN : External Regulator Current Sense Enable.
bits : 30 - 30 (1 bit)
Enumeration:
0 : DISABLED
Disable external regulator current sensing.
1 : ENABLED
Enable external regulator current sensing.
End of enumeration elements list.
ADCISNSEN : ADC Current Sense Enable.
bits : 31 - 31 (1 bit)
Enumeration:
0 : DISABLED
Disable ADC current sensing.
1 : ENABLED
Enable ADC current sensing.
End of enumeration elements list.
Current Sense Configuration
address_offset : 0x50 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
ISADCGAIN : ADC Current Sense Gain.
bits : 0 - 2 (3 bit)
Enumeration:
0 : 16X
ADC current sensing input gain is 16.
1 : 8X
ADC current sensing input gain is 8.
2 : 4X
ADC current sensing input gain is 4.
3 : 2X
ADC current sensing input gain is 2.
4 : 1X
ADC current sensing input gain is 1.
End of enumeration elements list.
ISOGAIN : External Regulator Current Sense Gain.
bits : 3 - 5 (3 bit)
Enumeration:
0 : 16X
External regulator current sensing gain is 16.
1 : 8X
External regulator current sensing gain is 8.
2 : 4X
External regulator current sensing gain is 4.
3 : 2X
External regulator current sensing gain is 2.
4 : 1X
External regulator current sensing gain is 1.
End of enumeration elements list.
ISINSEL : External Regulator Current Sense Input Select.
bits : 6 - 7 (2 bit)
Enumeration:
0 : MODE0
Select external regulator current sensing mode 0.
1 : MODE1
Select external regulator current sensing mode 1.
2 : MODE2
Select external regulator current sensing mode 2.
End of enumeration elements list.
Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !
This website is sponsored by Embeetle, an IDE designed from scratch for embedded software developers.