\n
address_offset : 0x0 Bytes (0x0)
size : 0xFFC byte (0x0)
mem_usage : registers
protection : not protected
RTC Configuration
address_offset : 0x0 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
ALM0AREN : Alarm 0 Automatic Reset Enable.
bits : 0 - 0 (1 bit)
Enumeration:
0 : DISABLED
Disable the Alarm 0 automatic reset.
1 : ENABLED
Enable the Alarm 0 automatic reset.
End of enumeration elements list.
RUN : RTC Timer Enable.
bits : 1 - 1 (1 bit)
Enumeration:
0 : STOP
Stop the RTC timer.
1 : START
Start the RTC timer running.
End of enumeration elements list.
MCLKEN : Missing Clock Detector Enable.
bits : 2 - 2 (1 bit)
Enumeration:
0 : DISABLED
Disable the missing clock detector.
1 : ENABLED
Enable the missing clock detector. If the missing clock detector triggers, it will generate an RTC Fail event.
End of enumeration elements list.
ASEN : Automatic Crystal Load Capacitance Stepping Enable.
bits : 3 - 3 (1 bit)
Enumeration:
0 : DISABLED
Disable automatic load capacitance stepping.
1 : ENABLED
Enable automatic load capacitance stepping.
End of enumeration elements list.
RTCLC : Load Capacitance Value.
bits : 4 - 7 (4 bit)
BDEN : Bias Doubler Enable.
bits : 16 - 16 (1 bit)
Enumeration:
0 : DISABLED
Disable the bias doubler, saving power.
1 : ENABLED
Enable the bias doubler, allowing for faster oscillator start up time.
End of enumeration elements list.
CRYSEN : Crystal Oscillator Enable.
bits : 17 - 17 (1 bit)
Enumeration:
0 : DISABLED
Disable the crystal oscillator circuitry.
1 : ENABLED
Enable the crystal oscillator circuitry.
End of enumeration elements list.
AGCEN : Automatic Gain Control Enable.
bits : 18 - 18 (1 bit)
Enumeration:
0 : DISABLED
Disable automatic gain control.
1 : ENABLED
Enable automatic gain control, saving power.
End of enumeration elements list.
ALM0EN : Alarm 0 Enable.
bits : 24 - 24 (1 bit)
Enumeration:
0 : DISABLED
Disable RTC Alarm 0.
1 : ENABLED
Enable RTC Alarm 0.
End of enumeration elements list.
ALM1EN : Alarm 1 Enable.
bits : 25 - 25 (1 bit)
Enumeration:
0 : DISABLED
Disable RTC Alarm 1.
1 : ENABLED
Enable RTC Alarm 1.
End of enumeration elements list.
ALM2EN : Alarm 2 Enable.
bits : 26 - 26 (1 bit)
Enumeration:
0 : DISABLED
Disable RTC Alarm 2.
1 : ENABLED
Enable RTC Alarm 2.
End of enumeration elements list.
RTCOEN : RTC0 External Output Enable.
bits : 29 - 29 (1 bit)
Enumeration:
0 : DISABLED
Disable the external RTCnOSC output.
1 : ENABLED
Enable the external RTCnOSC output.
End of enumeration elements list.
CLKSEL : RTC Timer Clock Select.
bits : 30 - 30 (1 bit)
Enumeration:
0 : RTCNOSC
Select the RTC clock (RTCnOSC) as the RTC Timer clock.
1 : LFOSCN
Select the Low Frequency Oscillator (LFOSCn) clock as the RTC Timer clock.
End of enumeration elements list.
RTCEN : RTC Oscillator and Timer Enable.
bits : 31 - 31 (1 bit)
Enumeration:
0 : DISABLED
Disable the RTC Oscillator and Timer.
1 : ENABLED
Enable the RTC Oscillator and Timer.
End of enumeration elements list.
RTC Control
address_offset : 0x10 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
ALM0I : Alarm 0 Interrupt Flag.
bits : 0 - 0 (1 bit)
Enumeration:
0 : NOT_SET
Alarm 0 event has not occurred.
1 : SET
Alarm 0 event occurred.
End of enumeration elements list.
ALM1I : Alarm 1 Interrupt Flag.
bits : 1 - 1 (1 bit)
Enumeration:
0 : NOT_SET
Alarm 1 event has not occurred.
1 : SET
Alarm 1 event occurred.
End of enumeration elements list.
ALM2I : Alarm 2 Interrupt Flag.
bits : 2 - 2 (1 bit)
Enumeration:
0 : NOT_SET
Alarm 2 event has not occurred.
1 : SET
Alarm 2 event occurred.
End of enumeration elements list.
TMRCAP : RTC Timer Capture.
bits : 3 - 3 (1 bit)
Enumeration:
0 : NOT_SET
RTC timer capture operation is complete.
1 : SET
Start the RTC timer capture.
End of enumeration elements list.
TMRSET : RTC Timer Set.
bits : 4 - 4 (1 bit)
Enumeration:
0 : NOT_SET
RTC timer set operation is complete.
1 : SET
Start the RTC timer set.
End of enumeration elements list.
CLKVF : RTC External Oscillator Valid Flag.
bits : 5 - 5 (1 bit)
access : read-only
Enumeration:
0 : NOT_SET
External oscillator is not valid.
1 : SET
External oscillator is valid.
End of enumeration elements list.
OSCFI : RTC Oscillator Fail Interrupt Flag.
bits : 6 - 6 (1 bit)
Enumeration:
0 : NOT_SET
Oscillator is running.
1 : SET
Oscillator has failed.
End of enumeration elements list.
HSMDEN : RTC High Speed Mode Enable.
bits : 7 - 7 (1 bit)
Enumeration:
0 : DISABLED
Disable high speed mode.
1 : ENABLED
Enable high speed mode.
End of enumeration elements list.
LRDYF : RTC Load Capacitance Ready Flag.
bits : 8 - 8 (1 bit)
access : read-only
Enumeration:
0 : NOT_SET
The load capacitance is currently stepping.
1 : SET
The load capacitance has reached its programmed value.
End of enumeration elements list.
RTC Alarm 0
address_offset : 0x20 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
ALARM0 : RTC Alarm 0.
bits : 0 - 31 (32 bit)
RTC Alarm 1
address_offset : 0x30 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
ALARM1 : RTC Alarm 1.
bits : 0 - 31 (32 bit)
RTC Alarm 2
address_offset : 0x40 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
ALARM2 : RTC Alarm 2.
bits : 0 - 31 (32 bit)
RTC Timer Set/Capture Value
address_offset : 0x50 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
SETCAP : RTC Timer Set/Capture Value.
bits : 0 - 31 (32 bit)
LFOSC Control
address_offset : 0x60 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
LFOSCEN : Low Frequency Oscillator Enable.
bits : 31 - 31 (1 bit)
Enumeration:
0 : DISABLED
Disable the Low Frequency Oscillator (LFOSCn).
1 : ENABLED
Enable the Low Frequency Oscillator (LFOSCn).
End of enumeration elements list.
LFOSC Output Frequency Adjust
address_offset : 0x80 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
LFOSCADJ : LFOSC Output Frequency Adjust.
bits : 0 - 3 (4 bit)
Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !
This website is sponsored by Embeetle, an IDE designed from scratch for embedded software developers.