\n

PMU_0

Peripheral Memory Blocks

address_offset : 0x0 Bytes (0x0)
size : 0xFFC byte (0x0)
mem_usage : registers
protection : not protected

Registers

CONTROL

CONFIG

STATUS

WAKEEN

WAKESTATUS

PWEN

PWPOL


CONTROL

Module Control
address_offset : 0x0 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

CONTROL CONTROL read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 WAKECLR PWAKEEN PMUASLPEN CPMONEN CPMONIEN RAM0REN RAM1REN RAM2REN RAM3REN RAM4REN RAM5REN RAM6REN RAM7REN

WAKECLR : Wakeup Source Clear.
bits : 0 - 0 (1 bit)
access : write-only

Enumeration:

0 : CLEAR

Clear all wakeup sources.

End of enumeration elements list.

PWAKEEN : Pin Wake Match Enable.
bits : 3 - 3 (1 bit)

Enumeration:

0 : DISABLED

Disable Pin Wake.

1 : ENABLED

Enable Pin Wake.

End of enumeration elements list.

PMUASLPEN : PMU Asleep Pin Enable.
bits : 4 - 4 (1 bit)

Enumeration:

0 : DISABLED

Disable the PMU Asleep pin.

1 : ENABLED

Enable the PMU Asleep pin.

End of enumeration elements list.

CPMONEN : Low Power Charge Pump Voltage Monitor Enable.
bits : 5 - 5 (1 bit)

Enumeration:

0 : DISABLED

Disable the low power charge pump voltage monitor.

1 : ENABLED

Enable the low power charge pump voltage monitor.

End of enumeration elements list.

CPMONIEN : Low Power Charge Pump Voltage Monitor Interrupt Enable.
bits : 6 - 6 (1 bit)

Enumeration:

0 : DISABLED

Disable the low power charge pump voltage monitor interrupt.

1 : ENABLED

Enable the low power charge pump voltage monitor interrupt.

End of enumeration elements list.

RAM0REN : RAM 0 Retention Enable.
bits : 16 - 16 (1 bit)

Enumeration:

0 : DISABLED

Disable power to RAM 0 (4 kB addresses from 0x20000000 to 0x20000FFF).

1 : ENABLED

Disable power to RAM 0 (4 kB addresses from 0x20000000 to 0x20000FFF).

End of enumeration elements list.

RAM1REN : RAM 1 Retention Enable.
bits : 17 - 17 (1 bit)

Enumeration:

0 : DISABLED

Disable power to RAM 1 (4 kB addresses from 0x20001000 to 0x20001FFF).

1 : ENABLED

Disable power to RAM 1 (4 kB addresses from 0x20001000 to 0x20001FFF).

End of enumeration elements list.

RAM2REN : RAM 2 Retention Enable.
bits : 18 - 18 (1 bit)

Enumeration:

0 : DISABLED

Disable power to RAM 0 (4 kB addresses from 0x20002000 to 0x20002FFF).

1 : ENABLED

Disable power to RAM 0 (4 kB addresses from 0x20002000 to 0x20002FFF).

End of enumeration elements list.

RAM3REN : RAM 3 Retention Enable.
bits : 19 - 19 (1 bit)

Enumeration:

0 : DISABLED

Disable power to RAM 3 (4 kB addresses from 0x20003000 to 0x20003FFF).

1 : ENABLED

Disable power to RAM 3 (4 kB addresses from 0x20003000 to 0x20003FFF).

End of enumeration elements list.

RAM4REN : RAM 4 Retention Enable.
bits : 20 - 20 (1 bit)

Enumeration:

0 : DISABLED

Disable power to RAM 4 (4 kB addresses from 0x20004000 to 0x20004FFF).

1 : ENABLED

Disable power to RAM 4 (4 kB addresses from 0x20004000 to 0x20004FFF).

End of enumeration elements list.

RAM5REN : RAM 5 Retention Enable.
bits : 21 - 21 (1 bit)

Enumeration:

0 : DISABLED

Disable power to RAM 5 (4 kB addresses from 0x20005000 to 0x20005FFF).

1 : ENABLED

Disable power to RAM 5 (4 kB addresses from 0x20005000 to 0x20005FFF).

End of enumeration elements list.

RAM6REN : RAM 6 Retention Enable.
bits : 22 - 22 (1 bit)

Enumeration:

0 : DISABLED

Disable power to RAM 6 (4 kB addresses from 0x20006000 to 0x20006FFF).

1 : ENABLED

Disable power to RAM 6 (4 kB addresses from 0x20006000 to 0x20006FFF).

End of enumeration elements list.

RAM7REN : RAM 7 Retention Enable.
bits : 23 - 23 (1 bit)

Enumeration:

0 : DISABLED

Disable power to RAM 7 (4 kB addresses from 0x20007000 to 0x20007FFF).

1 : ENABLED

Disable power to RAM 7 (4 kB addresses from 0x20007000 to 0x20007FFF).

End of enumeration elements list.


CONFIG

Module Configuration
address_offset : 0x10 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

CONFIG CONFIG read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 VBATMONEN VDRVSMD CPEN CPLOAD

VBATMONEN : VBAT Monitor Disable.
bits : 4 - 4 (1 bit)

Enumeration:

0 : ENABLED

Enable the 0.8 V VBAT monitor.

1 : DISABLED

Disable the 0.8V VBAT monitor.

End of enumeration elements list.

VDRVSMD : VDRV Switch Mode.
bits : 5 - 6 (2 bit)

Enumeration:

0 : HIGHZ

High-Z.

2 : VBAT

VBAT connected to VDRV.

3 : VDC

DC-DC output connected to VDRV.

End of enumeration elements list.

CPEN : Low Power Charge Pump Enable.
bits : 8 - 8 (1 bit)

Enumeration:

0 : DISABLED

None

1 : ENABLED

None

End of enumeration elements list.

CPLOAD : Charge Pump Load Setting.
bits : 10 - 11 (2 bit)


STATUS

Module Status
address_offset : 0x20 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

STATUS STATUS read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 PM8EF PWAKEF PORF CPSTS

PM8EF : Power Mode 8 Exited Flag.
bits : 0 - 0 (1 bit)

Enumeration:

0 : NOT_SET

The device has not exited Power Mode 8.

1 : SET

The device has exited Power Mode 8. This bit must be cleared by firmware.

End of enumeration elements list.

PWAKEF : Pin Wake Status Flag.
bits : 1 - 1 (1 bit)
access : read-only

Enumeration:

0 : NOT_SET

A Pin Wake event has not occurred.

1 : SET

A Pin Wake event has occurred.

End of enumeration elements list.

PORF : Power-On Reset Flag.
bits : 2 - 2 (1 bit)

Enumeration:

0 : NOT_SET

A power-on reset did not occur since the last time PORF was cleared.

1 : SET

A power-on reset occurred.

End of enumeration elements list.

CPSTS : Low Power Charge Pump Voltage Monitor Status.
bits : 3 - 3 (1 bit)
access : read-only

Enumeration:

0 : NOT_SET

The low power charge pump supply voltage is below the threshold.

1 : SET

The low power charge pump supply voltage is greater than the threshold.

End of enumeration elements list.


WAKEEN

Wakeup Enable
address_offset : 0x30 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

WAKEEN WAKEEN read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 RTC0FWEN RTC0A0WEN CMP0WEN ACC0WEN LCDMONWEN PWAKEWEN LPT0WEN UART0WEN CPFWEN

RTC0FWEN : RTC0 Fail Wake Enable.
bits : 0 - 0 (1 bit)

Enumeration:

0 : DISABLED

An RTC0 Fail event does not wake the device.

1 : ENABLED

An RTC0 Fail event awakens the device.

End of enumeration elements list.

RTC0A0WEN : RTC0 Alarm 0 Wake Enable.
bits : 1 - 1 (1 bit)

Enumeration:

0 : DISABLED

An RTC0 Alarm 0 event does not wake the device.

1 : ENABLED

An RTC0 Alarm 0 event awakens the device.

End of enumeration elements list.

CMP0WEN : Comparator 0 Wake Enable.
bits : 2 - 2 (1 bit)

Enumeration:

0 : DISABLED

A Comparator 0 event does not wake the device.

1 : ENABLED

A Comparator 0 event awakens the device.

End of enumeration elements list.

ACC0WEN : Advanced Capture Counter 0 Wake Enable.
bits : 3 - 3 (1 bit)

Enumeration:

0 : DISABLED

An Advanced Capture Counter (ACCTR0) event does not wake the device.

1 : ENABLED

An Advanced Capture Counter (ACCTR0) event awakens the device.

End of enumeration elements list.

LCDMONWEN : LCD VBAT Voltage Monitor Wake Enable.
bits : 4 - 4 (1 bit)

Enumeration:

0 : DISABLED

An LCD VBAT voltage monitor event does not wake the device.

1 : ENABLED

An LCD VBAT voltage monitor event awakens the device.

End of enumeration elements list.

PWAKEWEN : Pin Wake Wake Enable.
bits : 5 - 5 (1 bit)

Enumeration:

0 : DISABLED

A Pin Wake event does not wake the device.

1 : ENABLED

A Pin Wake event awakens the device.

End of enumeration elements list.

LPT0WEN : Low Power Timer Wake Enable.
bits : 6 - 6 (1 bit)

Enumeration:

0 : DISABLED

An LPTIMER0 event does not wake the device.

1 : ENABLED

An LPTIMER0 event awakens the device.

End of enumeration elements list.

UART0WEN : UART0 Wake Enable.
bits : 7 - 7 (1 bit)

Enumeration:

0 : DISABLED

A UART0 event does not wake the device.

1 : ENABLED

A UART0 event awakens the device.

End of enumeration elements list.

CPFWEN : Low Power Charge Pump Supply Fail Wake Enable.
bits : 8 - 8 (1 bit)

Enumeration:

0 : DISABLED

A low power charge pump supply fail event does not wake the device.

1 : ENABLED

A low power charge pump supply fail event awakens the device.

End of enumeration elements list.


WAKESTATUS

Wakeup Status
address_offset : 0x40 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

WAKESTATUS WAKESTATUS read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 RTC0FWF RTC0A0WF CMP0WF ACC0WF LCDMONWF PWAKEWF LPT0WF UART0WF CPFWF RSTWF

RTC0FWF : RTC0 Fail Wake Flag.
bits : 0 - 0 (1 bit)
access : read-only

Enumeration:

0 : NOT_SET

An RTC0 Fail event did not wake the device.

1 : SET

An RTC0 Fail event woke the device.

End of enumeration elements list.

RTC0A0WF : RTC0 Alarm 0 Wake Flag.
bits : 1 - 1 (1 bit)
access : read-only

Enumeration:

0 : NOT_SET

An RTC0 Alarm 0 event did not wake the device.

1 : SET

An RTC0 0 Alarm event woke the device.

End of enumeration elements list.

CMP0WF : Comparator 0 Wake Flag.
bits : 2 - 2 (1 bit)
access : read-only

Enumeration:

0 : NOT_SET

A Comparator 0 event did not wake the device.

1 : SET

A Comparator 0 event woke the device.

End of enumeration elements list.

ACC0WF : Advanced Capture Counter 0 Wake Flag.
bits : 3 - 3 (1 bit)
access : read-only

Enumeration:

0 : NOT_SET

An Advanced Capture Counter (ACCTR0) event did not wake the device.

1 : SET

An Advanced Capture Counter (ACCTR0) event woke the device.

End of enumeration elements list.

LCDMONWF : LCD VBAT Voltage Monitor Wake Flag.
bits : 4 - 4 (1 bit)
access : read-only

Enumeration:

0 : NOT_SET

A LCD VBAT voltage monitor event did not wake the device.

1 : SET

A LCD VBAT voltage monitor event woke the device.

End of enumeration elements list.

PWAKEWF : Pin Wake Wake Flag.
bits : 5 - 5 (1 bit)
access : read-only

Enumeration:

0 : NOT_SET

A Pin Wake event did not wake the device.

1 : SET

A Pin Wake event woke the device.

End of enumeration elements list.

LPT0WF : Low Power Timer Wake Flag.
bits : 6 - 6 (1 bit)
access : read-only

Enumeration:

0 : NOT_SET

An LPTIMER0 event did not wake the device.

1 : SET

An LPTIMER0 event woke the device.

End of enumeration elements list.

UART0WF : UART0 Wake Flag.
bits : 7 - 7 (1 bit)
access : read-only

Enumeration:

0 : NOT_SET

A UART0 event did not wake the device.

1 : SET

A UART0 event woke the device.

End of enumeration elements list.

CPFWF : Low Power Charge Pump Supply Fail Wake Flag.
bits : 8 - 8 (1 bit)
access : read-only

Enumeration:

0 : NOT_SET

A low power charge pump supply fail event did not wake the device.

1 : SET

A low power charge pump supply fail event woke the device.

End of enumeration elements list.

RSTWF : Reset Pin Wake Flag.
bits : 9 - 9 (1 bit)
access : read-only

Enumeration:

0 : NOT_SET

A /RESET Pin event did not wake the device.

1 : SET

A /RESET Pin event woke the device.

End of enumeration elements list.


PWEN

Pin Wake Pin Enable
address_offset : 0x50 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PWEN PWEN read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 PW0EN PW1EN PW2EN PW3EN PW4EN PW5EN PW6EN PW7EN PW8EN PW9EN PW10EN PW11EN PW12EN PW13EN PW14EN PW15EN

PW0EN : WAKE.0 Enable.
bits : 0 - 0 (1 bit)

Enumeration:

0 : DISABLED

WAKE.0 does not cause a Pin Wake event.

1 : ENABLED

Enable WAKE.0 as a Pin Wake source.

End of enumeration elements list.

PW1EN : WAKE.1 Enable.
bits : 1 - 1 (1 bit)

Enumeration:

0 : DISABLED

WAKE.1 does not cause a Pin Wake event.

1 : ENABLED

Enable WAKE.1 as a Pin Wake source.

End of enumeration elements list.

PW2EN : WAKE.2 Enable.
bits : 2 - 2 (1 bit)

Enumeration:

0 : DISABLED

WAKE.2 does not cause a Pin Wake event.

1 : ENABLED

Enable WAKE.2 as a Pin Wake source.

End of enumeration elements list.

PW3EN : WAKE.3 Enable.
bits : 3 - 3 (1 bit)

Enumeration:

0 : DISABLED

WAKE.3 does not cause a Pin Wake event.

1 : ENABLED

Enable WAKE.3 as a Pin Wake source.

End of enumeration elements list.

PW4EN : WAKE.4 Enable.
bits : 4 - 4 (1 bit)

Enumeration:

0 : DISABLED

WAKE.4 does not cause a Pin Wake event.

1 : ENABLED

Enable WAKE.4 as a Pin Wake source.

End of enumeration elements list.

PW5EN : WAKE.5 Enable.
bits : 5 - 5 (1 bit)

Enumeration:

0 : DISABLED

WAKE.5 does not cause a Pin Wake event.

1 : ENABLED

Enable WAKE.5 as a Pin Wake source.

End of enumeration elements list.

PW6EN : WAKE.6 Enable.
bits : 6 - 6 (1 bit)

Enumeration:

0 : DISABLED

WAKE.6 does not cause a Pin Wake event.

1 : ENABLED

Enable WAKE.6 as a Pin Wake source.

End of enumeration elements list.

PW7EN : WAKE.7 Enable.
bits : 7 - 7 (1 bit)

Enumeration:

0 : DISABLED

WAKE.7 does not cause a Pin Wake event.

1 : ENABLED

Enable WAKE.7 as a Pin Wake source.

End of enumeration elements list.

PW8EN : WAKE.8 Enable.
bits : 8 - 8 (1 bit)

Enumeration:

0 : DISABLED

WAKE.8 does not cause a Pin Wake event.

1 : ENABLED

Enable WAKE.8 as a Pin Wake source.

End of enumeration elements list.

PW9EN : WAKE.9 Enable.
bits : 9 - 9 (1 bit)

Enumeration:

0 : DISABLED

WAKE.9 does not cause a Pin Wake event.

1 : ENABLED

Enable WAKE.9 as a Pin Wake source.

End of enumeration elements list.

PW10EN : WAKE.10 Enable.
bits : 10 - 10 (1 bit)

Enumeration:

0 : DISABLED

WAKE.10 does not cause a Pin Wake event.

1 : ENABLED

Enable WAKE.10 as a Pin Wake source.

End of enumeration elements list.

PW11EN : WAKE.11 Enable.
bits : 11 - 11 (1 bit)

Enumeration:

0 : DISABLED

WAKE.11 does not cause a Pin Wake event.

1 : ENABLED

Enable WAKE.11 as a Pin Wake source.

End of enumeration elements list.

PW12EN : WAKE.12 Enable.
bits : 12 - 12 (1 bit)

Enumeration:

0 : DISABLED

WAKE.12 does not cause a Pin Wake event.

1 : ENABLED

Enable WAKE.12 as a Pin Wake source.

End of enumeration elements list.

PW13EN : WAKE.13 Enable.
bits : 13 - 13 (1 bit)

Enumeration:

0 : DISABLED

WAKE.13 does not cause a Pin Wake event.

1 : ENABLED

Enable WAKE.13 as a Pin Wake source.

End of enumeration elements list.

PW14EN : WAKE.14 Enable.
bits : 14 - 14 (1 bit)

Enumeration:

0 : DISABLED

WAKE.14 does not cause a Pin Wake event.

1 : ENABLED

Enable WAKE.14 as a Pin Wake source.

End of enumeration elements list.

PW15EN : WAKE.15 Enable.
bits : 15 - 15 (1 bit)

Enumeration:

0 : DISABLED

WAKE.15 does not cause a Pin Wake event.

1 : ENABLED

Enable WAKE.15 as a Pin Wake source.

End of enumeration elements list.


PWPOL

Pin Wake Pin Polarity Select
address_offset : 0x60 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PWPOL PWPOL read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 PW0POL PW1POL PW2POL PW3POL PW4POL PW5POL PW6POL PW7POL PW8POL PW9POL PW10POL PW11POL PW12POL PW13POL PW14POL PW15POL

PW0POL : WAKE.0 Polarity Select.
bits : 0 - 0 (1 bit)

Enumeration:

0 : LOW

A logic low on WAKE.0 causes a Pin Wake event if PW0EN is set to 1.

1 : HIGH

A logic high on WAKE.0 causes a Pin Wake event if PW0EN is set to 1.

End of enumeration elements list.

PW1POL : WAKE.1 Polarity Select.
bits : 1 - 1 (1 bit)

Enumeration:

0 : LOW

A logic low on WAKE.1 causes a Pin Wake event if PW1EN is set to 1.

1 : HIGH

A logic high on WAKE.1 causes a Pin Wake event if PW1EN is set to 1.

End of enumeration elements list.

PW2POL : WAKE.2 Polarity Select.
bits : 2 - 2 (1 bit)

Enumeration:

0 : LOW

A logic low on WAKE.2 causes a Pin Wake event if PW2EN is set to 1.

1 : HIGH

A logic high on WAKE.2 causes a Pin Wake event if PW2EN is set to 1.

End of enumeration elements list.

PW3POL : WAKE.3 Polarity Select.
bits : 3 - 3 (1 bit)

Enumeration:

0 : LOW

A logic low on WAKE.3 causes a Pin Wake event if PW3EN is set to 1.

1 : HIGH

A logic high on WAKE.3 causes a Pin Wake event if PW3EN is set to 1.

End of enumeration elements list.

PW4POL : WAKE.4 Polarity Select.
bits : 4 - 4 (1 bit)

Enumeration:

0 : LOW

A logic low on WAKE.4 causes a Pin Wake event if PW4EN is set to 1.

1 : HIGH

A logic high on WAKE.4 causes a Pin Wake event if PW4EN is set to 1.

End of enumeration elements list.

PW5POL : WAKE.5 Polarity Select.
bits : 5 - 5 (1 bit)

Enumeration:

0 : LOW

A logic low on WAKE.5 causes a Pin Wake event if PW5EN is set to 1.

1 : HIGH

A logic high on WAKE.5 causes a Pin Wake event if PW5EN is set to 1.

End of enumeration elements list.

PW6POL : WAKE.6 Polarity Select.
bits : 6 - 6 (1 bit)

Enumeration:

0 : LOW

A logic low on WAKE.6 causes a Pin Wake event if PW6EN is set to 1.

1 : HIGH

A logic high on WAKE.6 causes a Pin Wake event if PW6EN is set to 1.

End of enumeration elements list.

PW7POL : WAKE.7 Polarity Select.
bits : 7 - 7 (1 bit)

Enumeration:

0 : LOW

A logic low on WAKE.7 causes a Pin Wake event if PW7EN is set to 1.

1 : HIGH

A logic high on WAKE.7 causes a Pin Wake event if PW7EN is set to 1.

End of enumeration elements list.

PW8POL : WAKE.8 Polarity Select.
bits : 8 - 8 (1 bit)

Enumeration:

0 : LOW

A logic low on WAKE.8 causes a Pin Wake event if PW8EN is set to 1.

1 : HIGH

A logic high on WAKE.8 causes a Pin Wake event if PW8EN is set to 1.

End of enumeration elements list.

PW9POL : WAKE.9 Polarity Select.
bits : 9 - 9 (1 bit)

Enumeration:

0 : LOW

A logic low on WAKE.9 causes a Pin Wake event if PW9EN is set to 1.

1 : HIGH

A logic high on WAKE.9 causes a Pin Wake event if PW9EN is set to 1.

End of enumeration elements list.

PW10POL : WAKE.10 Polarity Select.
bits : 10 - 10 (1 bit)

Enumeration:

0 : LOW

A logic low on WAKE.10 causes a Pin Wake event if PW10EN is set to 1.

1 : HIGH

A logic high on WAKE.10 causes a Pin Wake event if PW10EN is set to 1.

End of enumeration elements list.

PW11POL : WAKE.11 Polarity Select.
bits : 11 - 11 (1 bit)

Enumeration:

0 : LOW

A logic low on WAKE.11 causes a Pin Wake event if PW11EN is set to 1.

1 : HIGH

A logic high on WAKE.11 causes a Pin Wake event if PW11EN is set to 1.

End of enumeration elements list.

PW12POL : WAKE.12 Polarity Select.
bits : 12 - 12 (1 bit)

Enumeration:

0 : LOW

A logic low on WAKE.12 causes a Pin Wake event if PW12EN is set to 1.

1 : HIGH

A logic high on WAKE.12 causes a Pin Wake event if PW12EN is set to 1.

End of enumeration elements list.

PW13POL : WAKE.13 Polarity Select.
bits : 13 - 13 (1 bit)

Enumeration:

0 : LOW

A logic low on WAKE.13 causes a Pin Wake event if PW13EN is set to 1.

1 : HIGH

A logic high on WAKE.13 causes a Pin Wake event if PW13EN is set to 1.

End of enumeration elements list.

PW14POL : WAKE.14 Polarity Select.
bits : 14 - 14 (1 bit)

Enumeration:

0 : LOW

A logic low on WAKE.14 causes a Pin Wake event if PW14EN is set to 1.

1 : HIGH

A logic high on WAKE.14 causes a Pin Wake event if PW14EN is set to 1.

End of enumeration elements list.

PW15POL : WAKE.15 Polarity Select.
bits : 15 - 15 (1 bit)

Enumeration:

0 : LOW

A logic low on WAKE.15 causes a Pin Wake event if PW15EN is set to 1.

1 : HIGH

A logic high on WAKE.15 causes a Pin Wake event if PW15EN is set to 1.

End of enumeration elements list.



Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !

This website is sponsored by EmbeetleEmbeetle, an IDE designed from scratch for embedded software developers.