\n
address_offset : 0x0 Bytes (0x0)
size : 0x50 byte (0x0)
mem_usage : registers
protection : not protected
Control Register
address_offset : 0x0 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
BACKUP : Backup Mode
bits : 0 - 0 (1 bit)
access : write-only
NORMAL : Normal Mode
bits : 1 - 1 (1 bit)
access : write-only
SWPROT : Software Protection
bits : 2 - 2 (1 bit)
access : write-only
SCRAMB : Memory Scrambling Enable
bits : 9 - 10 (2 bit)
access : write-only
KEY : Password
bits : 16 - 31 (16 bit)
access : write-only
Status Clear Register
address_offset : 0x10 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
DET0 : PIOBU Intrusion Detector
bits : 16 - 16 (1 bit)
access : write-only
DET1 : PIOBU Intrusion Detector
bits : 17 - 17 (1 bit)
access : write-only
DET2 : PIOBU Intrusion Detector
bits : 18 - 18 (1 bit)
access : write-only
DET3 : PIOBU Intrusion Detector
bits : 19 - 19 (1 bit)
access : write-only
DET4 : PIOBU Intrusion Detector
bits : 20 - 20 (1 bit)
access : write-only
DET5 : PIOBU Intrusion Detector
bits : 21 - 21 (1 bit)
access : write-only
DET6 : PIOBU Intrusion Detector
bits : 22 - 22 (1 bit)
access : write-only
DET7 : PIOBU Intrusion Detector
bits : 23 - 23 (1 bit)
access : write-only
PIO Backup Register
address_offset : 0x114 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PIOBU_AFV : PIOBU Alarm Filter Value
bits : 0 - 3 (4 bit)
access : read-write
PIOBU_RFV : PIOBUx Reset Filter Value
bits : 4 - 7 (4 bit)
access : read-write
OUTPUT : Configure I/O Line in Input/Output
bits : 8 - 8 (1 bit)
access : read-write
PIO_SOD : Set/Clear the I/O Line when configured in Output Mode (OUTPUT =1)
bits : 9 - 9 (1 bit)
access : read-write
PIO_PDS : Level on the Pin in Input Mode (OUTPUT = 0) (Read-only)
bits : 10 - 10 (1 bit)
access : read-write
PULLUP : Programmable Pull-up State
bits : 12 - 13 (2 bit)
access : read-write
SCHEDULE : Pull-up/Down Scheduled
bits : 14 - 14 (1 bit)
access : read-write
SWITCH : Switch State for Intrusion Detection
bits : 15 - 15 (1 bit)
access : read-write
RAM Access Ready Register
address_offset : 0x14 Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
READY : Ready for system access flag
bits : 0 - 0 (1 bit)
access : read-only
PIO Backup Register
address_offset : 0x148 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PIOBU_AFV : PIOBU Alarm Filter Value
bits : 0 - 3 (4 bit)
access : read-write
PIOBU_RFV : PIOBUx Reset Filter Value
bits : 4 - 7 (4 bit)
access : read-write
OUTPUT : Configure I/O Line in Input/Output
bits : 8 - 8 (1 bit)
access : read-write
PIO_SOD : Set/Clear the I/O Line when configured in Output Mode (OUTPUT =1)
bits : 9 - 9 (1 bit)
access : read-write
PIO_PDS : Level on the Pin in Input Mode (OUTPUT = 0) (Read-only)
bits : 10 - 10 (1 bit)
access : read-write
PULLUP : Programmable Pull-up State
bits : 12 - 13 (2 bit)
access : read-write
SCHEDULE : Pull-up/Down Scheduled
bits : 14 - 14 (1 bit)
access : read-write
SWITCH : Switch State for Intrusion Detection
bits : 15 - 15 (1 bit)
access : read-write
PIO Backup Register
address_offset : 0x18 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
PIOBU_AFV : PIOBU Alarm Filter Value
bits : 0 - 3 (4 bit)
access : read-write
PIOBU_RFV : PIOBUx Reset Filter Value
bits : 4 - 7 (4 bit)
access : read-write
OUTPUT : Configure I/O Line in Input/Output
bits : 8 - 8 (1 bit)
access : read-write
PIO_SOD : Set/Clear the I/O Line when configured in Output Mode (OUTPUT =1)
bits : 9 - 9 (1 bit)
access : read-write
PIO_PDS : Level on the Pin in Input Mode (OUTPUT = 0) (Read-only)
bits : 10 - 10 (1 bit)
access : read-write
PULLUP : Programmable Pull-up State
bits : 12 - 13 (2 bit)
access : read-write
SCHEDULE : Pull-up/Down Scheduled
bits : 14 - 14 (1 bit)
access : read-write
SWITCH : Switch State for Intrusion Detection
bits : 15 - 15 (1 bit)
access : read-write
PIO Backup Register
address_offset : 0x1C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
PIOBU_AFV : PIOBU Alarm Filter Value
bits : 0 - 3 (4 bit)
access : read-write
PIOBU_RFV : PIOBUx Reset Filter Value
bits : 4 - 7 (4 bit)
access : read-write
OUTPUT : Configure I/O Line in Input/Output
bits : 8 - 8 (1 bit)
access : read-write
PIO_SOD : Set/Clear the I/O Line when configured in Output Mode (OUTPUT =1)
bits : 9 - 9 (1 bit)
access : read-write
PIO_PDS : Level on the Pin in Input Mode (OUTPUT = 0) (Read-only)
bits : 10 - 10 (1 bit)
access : read-write
PULLUP : Programmable Pull-up State
bits : 12 - 13 (2 bit)
access : read-write
SCHEDULE : Pull-up/Down Scheduled
bits : 14 - 14 (1 bit)
access : read-write
SWITCH : Switch State for Intrusion Detection
bits : 15 - 15 (1 bit)
access : read-write
PIO Backup Register
address_offset : 0x20 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
PIOBU_AFV : PIOBU Alarm Filter Value
bits : 0 - 3 (4 bit)
access : read-write
PIOBU_RFV : PIOBUx Reset Filter Value
bits : 4 - 7 (4 bit)
access : read-write
OUTPUT : Configure I/O Line in Input/Output
bits : 8 - 8 (1 bit)
access : read-write
PIO_SOD : Set/Clear the I/O Line when configured in Output Mode (OUTPUT =1)
bits : 9 - 9 (1 bit)
access : read-write
PIO_PDS : Level on the Pin in Input Mode (OUTPUT = 0) (Read-only)
bits : 10 - 10 (1 bit)
access : read-write
PULLUP : Programmable Pull-up State
bits : 12 - 13 (2 bit)
access : read-write
SCHEDULE : Pull-up/Down Scheduled
bits : 14 - 14 (1 bit)
access : read-write
SWITCH : Switch State for Intrusion Detection
bits : 15 - 15 (1 bit)
access : read-write
PIO Backup Register
address_offset : 0x24 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
PIOBU_AFV : PIOBU Alarm Filter Value
bits : 0 - 3 (4 bit)
access : read-write
PIOBU_RFV : PIOBUx Reset Filter Value
bits : 4 - 7 (4 bit)
access : read-write
OUTPUT : Configure I/O Line in Input/Output
bits : 8 - 8 (1 bit)
access : read-write
PIO_SOD : Set/Clear the I/O Line when configured in Output Mode (OUTPUT =1)
bits : 9 - 9 (1 bit)
access : read-write
PIO_PDS : Level on the Pin in Input Mode (OUTPUT = 0) (Read-only)
bits : 10 - 10 (1 bit)
access : read-write
PULLUP : Programmable Pull-up State
bits : 12 - 13 (2 bit)
access : read-write
SCHEDULE : Pull-up/Down Scheduled
bits : 14 - 14 (1 bit)
access : read-write
SWITCH : Switch State for Intrusion Detection
bits : 15 - 15 (1 bit)
access : read-write
PIO Backup Register
address_offset : 0x28 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
PIOBU_AFV : PIOBU Alarm Filter Value
bits : 0 - 3 (4 bit)
access : read-write
PIOBU_RFV : PIOBUx Reset Filter Value
bits : 4 - 7 (4 bit)
access : read-write
OUTPUT : Configure I/O Line in Input/Output
bits : 8 - 8 (1 bit)
access : read-write
PIO_SOD : Set/Clear the I/O Line when configured in Output Mode (OUTPUT =1)
bits : 9 - 9 (1 bit)
access : read-write
PIO_PDS : Level on the Pin in Input Mode (OUTPUT = 0) (Read-only)
bits : 10 - 10 (1 bit)
access : read-write
PULLUP : Programmable Pull-up State
bits : 12 - 13 (2 bit)
access : read-write
SCHEDULE : Pull-up/Down Scheduled
bits : 14 - 14 (1 bit)
access : read-write
SWITCH : Switch State for Intrusion Detection
bits : 15 - 15 (1 bit)
access : read-write
PIO Backup Register
address_offset : 0x2C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
PIOBU_AFV : PIOBU Alarm Filter Value
bits : 0 - 3 (4 bit)
access : read-write
PIOBU_RFV : PIOBUx Reset Filter Value
bits : 4 - 7 (4 bit)
access : read-write
OUTPUT : Configure I/O Line in Input/Output
bits : 8 - 8 (1 bit)
access : read-write
PIO_SOD : Set/Clear the I/O Line when configured in Output Mode (OUTPUT =1)
bits : 9 - 9 (1 bit)
access : read-write
PIO_PDS : Level on the Pin in Input Mode (OUTPUT = 0) (Read-only)
bits : 10 - 10 (1 bit)
access : read-write
PULLUP : Programmable Pull-up State
bits : 12 - 13 (2 bit)
access : read-write
SCHEDULE : Pull-up/Down Scheduled
bits : 14 - 14 (1 bit)
access : read-write
SWITCH : Switch State for Intrusion Detection
bits : 15 - 15 (1 bit)
access : read-write
PIO Backup Register
address_offset : 0x30 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PIOBU_AFV : PIOBU Alarm Filter Value
bits : 0 - 3 (4 bit)
access : read-write
PIOBU_RFV : PIOBUx Reset Filter Value
bits : 4 - 7 (4 bit)
access : read-write
OUTPUT : Configure I/O Line in Input/Output
bits : 8 - 8 (1 bit)
access : read-write
PIO_SOD : Set/Clear the I/O Line when configured in Output Mode (OUTPUT =1)
bits : 9 - 9 (1 bit)
access : read-write
PIO_PDS : Level on the Pin in Input Mode (OUTPUT = 0) (Read-only)
bits : 10 - 10 (1 bit)
access : read-write
PULLUP : Programmable Pull-up State
bits : 12 - 13 (2 bit)
access : read-write
SCHEDULE : Pull-up/Down Scheduled
bits : 14 - 14 (1 bit)
access : read-write
SWITCH : Switch State for Intrusion Detection
bits : 15 - 15 (1 bit)
access : read-write
PIO Backup Register
address_offset : 0x30 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
PIOBU_AFV : PIOBU Alarm Filter Value
bits : 0 - 3 (4 bit)
access : read-write
PIOBU_RFV : PIOBUx Reset Filter Value
bits : 4 - 7 (4 bit)
access : read-write
OUTPUT : Configure I/O Line in Input/Output
bits : 8 - 8 (1 bit)
access : read-write
PIO_SOD : Set/Clear the I/O Line when configured in Output Mode (OUTPUT =1)
bits : 9 - 9 (1 bit)
access : read-write
PIO_PDS : Level on the Pin in Input Mode (OUTPUT = 0) (Read-only)
bits : 10 - 10 (1 bit)
access : read-write
PULLUP : Programmable Pull-up State
bits : 12 - 13 (2 bit)
access : read-write
SCHEDULE : Pull-up/Down Scheduled
bits : 14 - 14 (1 bit)
access : read-write
SWITCH : Switch State for Intrusion Detection
bits : 15 - 15 (1 bit)
access : read-write
PIO Backup Register
address_offset : 0x34 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
PIOBU_AFV : PIOBU Alarm Filter Value
bits : 0 - 3 (4 bit)
access : read-write
PIOBU_RFV : PIOBUx Reset Filter Value
bits : 4 - 7 (4 bit)
access : read-write
OUTPUT : Configure I/O Line in Input/Output
bits : 8 - 8 (1 bit)
access : read-write
PIO_SOD : Set/Clear the I/O Line when configured in Output Mode (OUTPUT =1)
bits : 9 - 9 (1 bit)
access : read-write
PIO_PDS : Level on the Pin in Input Mode (OUTPUT = 0) (Read-only)
bits : 10 - 10 (1 bit)
access : read-write
PULLUP : Programmable Pull-up State
bits : 12 - 13 (2 bit)
access : read-write
SCHEDULE : Pull-up/Down Scheduled
bits : 14 - 14 (1 bit)
access : read-write
SWITCH : Switch State for Intrusion Detection
bits : 15 - 15 (1 bit)
access : read-write
System Status Register
address_offset : 0x4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
ERASE_DONE : Erasable Memories State (RW)
bits : 0 - 0 (1 bit)
access : read-write
ERASE_ON : Erase Process Ongoing (RO)
bits : 1 - 1 (1 bit)
access : read-write
BACKUP : Backup Mode (RO)
bits : 2 - 2 (1 bit)
access : read-write
SWKUP : SWKUP State (RO)
bits : 3 - 3 (1 bit)
access : read-write
AUTOBKP : Automatic Backup Mode Enabled (RO)
bits : 6 - 6 (1 bit)
access : read-write
SCRAMB : Scrambling Enabled (RO)
bits : 7 - 7 (1 bit)
access : read-write
PIO Backup Register
address_offset : 0x4C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PIOBU_AFV : PIOBU Alarm Filter Value
bits : 0 - 3 (4 bit)
access : read-write
PIOBU_RFV : PIOBUx Reset Filter Value
bits : 4 - 7 (4 bit)
access : read-write
OUTPUT : Configure I/O Line in Input/Output
bits : 8 - 8 (1 bit)
access : read-write
PIO_SOD : Set/Clear the I/O Line when configured in Output Mode (OUTPUT =1)
bits : 9 - 9 (1 bit)
access : read-write
PIO_PDS : Level on the Pin in Input Mode (OUTPUT = 0) (Read-only)
bits : 10 - 10 (1 bit)
access : read-write
PULLUP : Programmable Pull-up State
bits : 12 - 13 (2 bit)
access : read-write
SCHEDULE : Pull-up/Down Scheduled
bits : 14 - 14 (1 bit)
access : read-write
SWITCH : Switch State for Intrusion Detection
bits : 15 - 15 (1 bit)
access : read-write
JTAG Protection Control Register
address_offset : 0x68 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FNTRST : Force NTRST
bits : 0 - 0 (1 bit)
access : read-write
CA5_DEBUG_MODE : Cortex-A5 Invasive/Non-Invasive Secure/Non-Secure Debug Permissions
bits : 1 - 3 (3 bit)
access : read-write
WZO : Write ZERO
bits : 4 - 4 (1 bit)
access : read-write
PIO Backup Register
address_offset : 0x6C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PIOBU_AFV : PIOBU Alarm Filter Value
bits : 0 - 3 (4 bit)
access : read-write
PIOBU_RFV : PIOBUx Reset Filter Value
bits : 4 - 7 (4 bit)
access : read-write
OUTPUT : Configure I/O Line in Input/Output
bits : 8 - 8 (1 bit)
access : read-write
PIO_SOD : Set/Clear the I/O Line when configured in Output Mode (OUTPUT =1)
bits : 9 - 9 (1 bit)
access : read-write
PIO_PDS : Level on the Pin in Input Mode (OUTPUT = 0) (Read-only)
bits : 10 - 10 (1 bit)
access : read-write
PULLUP : Programmable Pull-up State
bits : 12 - 13 (2 bit)
access : read-write
SCHEDULE : Pull-up/Down Scheduled
bits : 14 - 14 (1 bit)
access : read-write
SWITCH : Switch State for Intrusion Detection
bits : 15 - 15 (1 bit)
access : read-write
Scrambling Key Register
address_offset : 0x70 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
SCRKEY : Scrambling Key Value
bits : 0 - 31 (32 bit)
access : read-write
RAM Access Rights Register
address_offset : 0x74 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RW0 : Access right for RAM region [0; 1 Kbyte]
bits : 0 - 1 (2 bit)
access : read-write
RW1 : Access right for RAM region [1 Kbyte; 2 Kbytes]
bits : 2 - 3 (2 bit)
access : read-write
RW2 : Access right for RAM region [2 Kbytes; 3 Kbytes]
bits : 4 - 5 (2 bit)
access : read-write
RW3 : Access right for RAM region [3 Kbytes; 4 Kbytes]
bits : 6 - 7 (2 bit)
access : read-write
RW4 : Access right for RAM region [4 Kbytes; 5 Kbytes]
bits : 8 - 9 (2 bit)
access : read-write
RW5 : Access right for RAM region [5 Kbytes; 6 Kbytes] (register bank BUREG256b)
bits : 10 - 11 (2 bit)
access : read-write
RAM Access Rights Status Register
address_offset : 0x78 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RW0 : Access right status for RAM region [0; 1 Kbyte]
bits : 0 - 1 (2 bit)
access : read-write
RW1 : Access right status for RAM region [1 Kbytes; 2 Kbytes]
bits : 2 - 3 (2 bit)
access : read-write
RW2 : Access right status for RAM region [2 Kbytes; 3 Kbytes]
bits : 4 - 5 (2 bit)
access : read-write
RW3 : Access right status for RAM region [3 Kbytes; 4 Kbytes]
bits : 6 - 7 (2 bit)
access : read-write
RW4 : Access right status for RAM region [4 Kbytes; 5 Kbytes]
bits : 8 - 9 (2 bit)
access : read-write
RW5 : Access right status for RAM region [5 Kbytes; 6 Kbytes] (register bank BUREG256b)
bits : 10 - 11 (2 bit)
access : read-write
Backup Mode Protection Register
address_offset : 0x7C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DET0 : PIOBU Intrusion Detector Protection
bits : 16 - 16 (1 bit)
access : read-write
DET1 : PIOBU Intrusion Detector Protection
bits : 17 - 17 (1 bit)
access : read-write
DET2 : PIOBU Intrusion Detector Protection
bits : 18 - 18 (1 bit)
access : read-write
DET3 : PIOBU Intrusion Detector Protection
bits : 19 - 19 (1 bit)
access : read-write
DET4 : PIOBU Intrusion Detector Protection
bits : 20 - 20 (1 bit)
access : read-write
DET5 : PIOBU Intrusion Detector Protection
bits : 21 - 21 (1 bit)
access : read-write
DET6 : PIOBU Intrusion Detector Protection
bits : 22 - 22 (1 bit)
access : read-write
DET7 : PIOBU Intrusion Detector Protection
bits : 23 - 23 (1 bit)
access : read-write
Status Register
address_offset : 0x8 Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
DET0 : PIOBU Intrusion Detector
bits : 16 - 16 (1 bit)
access : read-only
DET1 : PIOBU Intrusion Detector
bits : 17 - 17 (1 bit)
access : read-only
DET2 : PIOBU Intrusion Detector
bits : 18 - 18 (1 bit)
access : read-only
DET3 : PIOBU Intrusion Detector
bits : 19 - 19 (1 bit)
access : read-only
DET4 : PIOBU Intrusion Detector
bits : 20 - 20 (1 bit)
access : read-only
DET5 : PIOBU Intrusion Detector
bits : 21 - 21 (1 bit)
access : read-only
DET6 : PIOBU Intrusion Detector
bits : 22 - 22 (1 bit)
access : read-only
DET7 : PIOBU Intrusion Detector
bits : 23 - 23 (1 bit)
access : read-only
Normal Mode Protection Register
address_offset : 0x80 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DET0 : PIOBU Intrusion Detector Protection
bits : 16 - 16 (1 bit)
access : read-write
DET1 : PIOBU Intrusion Detector Protection
bits : 17 - 17 (1 bit)
access : read-write
DET2 : PIOBU Intrusion Detector Protection
bits : 18 - 18 (1 bit)
access : read-write
DET3 : PIOBU Intrusion Detector Protection
bits : 19 - 19 (1 bit)
access : read-write
DET4 : PIOBU Intrusion Detector Protection
bits : 20 - 20 (1 bit)
access : read-write
DET5 : PIOBU Intrusion Detector Protection
bits : 21 - 21 (1 bit)
access : read-write
DET6 : PIOBU Intrusion Detector Protection
bits : 22 - 22 (1 bit)
access : read-write
DET7 : PIOBU Intrusion Detector Protection
bits : 23 - 23 (1 bit)
access : read-write
Normal Interrupt Enable Protection Register
address_offset : 0x84 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
DET0 : PIOBU Intrusion Detector Protection Interrupt Enable
bits : 16 - 16 (1 bit)
access : write-only
DET1 : PIOBU Intrusion Detector Protection Interrupt Enable
bits : 17 - 17 (1 bit)
access : write-only
DET2 : PIOBU Intrusion Detector Protection Interrupt Enable
bits : 18 - 18 (1 bit)
access : write-only
DET3 : PIOBU Intrusion Detector Protection Interrupt Enable
bits : 19 - 19 (1 bit)
access : write-only
DET4 : PIOBU Intrusion Detector Protection Interrupt Enable
bits : 20 - 20 (1 bit)
access : write-only
DET5 : PIOBU Intrusion Detector Protection Interrupt Enable
bits : 21 - 21 (1 bit)
access : write-only
DET6 : PIOBU Intrusion Detector Protection Interrupt Enable
bits : 22 - 22 (1 bit)
access : write-only
DET7 : PIOBU Intrusion Detector Protection Interrupt Enable
bits : 23 - 23 (1 bit)
access : write-only
Normal Interrupt Disable Protection Register
address_offset : 0x88 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
DET0 : PIOBU Intrusion Detector Protection Interrupt Disable
bits : 16 - 16 (1 bit)
access : write-only
DET1 : PIOBU Intrusion Detector Protection Interrupt Disable
bits : 17 - 17 (1 bit)
access : write-only
DET2 : PIOBU Intrusion Detector Protection Interrupt Disable
bits : 18 - 18 (1 bit)
access : write-only
DET3 : PIOBU Intrusion Detector Protection Interrupt Disable
bits : 19 - 19 (1 bit)
access : write-only
DET4 : PIOBU Intrusion Detector Protection Interrupt Disable
bits : 20 - 20 (1 bit)
access : write-only
DET5 : PIOBU Intrusion Detector Protection Interrupt Disable
bits : 21 - 21 (1 bit)
access : write-only
DET6 : PIOBU Intrusion Detector Protection Interrupt Disable
bits : 22 - 22 (1 bit)
access : write-only
DET7 : PIOBU Intrusion Detector Protection Interrupt Disable
bits : 23 - 23 (1 bit)
access : write-only
Normal Interrupt Mask Protection Register
address_offset : 0x8C Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
DET0 : PIOBU Intrusion Detector Protection Interrupt Mask
bits : 16 - 16 (1 bit)
access : read-only
DET1 : PIOBU Intrusion Detector Protection Interrupt Mask
bits : 17 - 17 (1 bit)
access : read-only
DET2 : PIOBU Intrusion Detector Protection Interrupt Mask
bits : 18 - 18 (1 bit)
access : read-only
DET3 : PIOBU Intrusion Detector Protection Interrupt Mask
bits : 19 - 19 (1 bit)
access : read-only
DET4 : PIOBU Intrusion Detector Protection Interrupt Mask
bits : 20 - 20 (1 bit)
access : read-only
DET5 : PIOBU Intrusion Detector Protection Interrupt Mask
bits : 21 - 21 (1 bit)
access : read-only
DET6 : PIOBU Intrusion Detector Protection Interrupt Mask
bits : 22 - 22 (1 bit)
access : read-only
DET7 : PIOBU Intrusion Detector Protection Interrupt Mask
bits : 23 - 23 (1 bit)
access : read-only
PIO Backup Register
address_offset : 0x90 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PIOBU_AFV : PIOBU Alarm Filter Value
bits : 0 - 3 (4 bit)
access : read-write
PIOBU_RFV : PIOBUx Reset Filter Value
bits : 4 - 7 (4 bit)
access : read-write
OUTPUT : Configure I/O Line in Input/Output
bits : 8 - 8 (1 bit)
access : read-write
PIO_SOD : Set/Clear the I/O Line when configured in Output Mode (OUTPUT =1)
bits : 9 - 9 (1 bit)
access : read-write
PIO_PDS : Level on the Pin in Input Mode (OUTPUT = 0) (Read-only)
bits : 10 - 10 (1 bit)
access : read-write
PULLUP : Programmable Pull-up State
bits : 12 - 13 (2 bit)
access : read-write
SCHEDULE : Pull-up/Down Scheduled
bits : 14 - 14 (1 bit)
access : read-write
SWITCH : Switch State for Intrusion Detection
bits : 15 - 15 (1 bit)
access : read-write
Wakeup Protection Register
address_offset : 0x90 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DET0 : PIOBU Intrusion Detector Protection
bits : 16 - 16 (1 bit)
access : read-write
DET1 : PIOBU Intrusion Detector Protection
bits : 17 - 17 (1 bit)
access : read-write
DET2 : PIOBU Intrusion Detector Protection
bits : 18 - 18 (1 bit)
access : read-write
DET3 : PIOBU Intrusion Detector Protection
bits : 19 - 19 (1 bit)
access : read-write
DET4 : PIOBU Intrusion Detector Protection
bits : 20 - 20 (1 bit)
access : read-write
DET5 : PIOBU Intrusion Detector Protection
bits : 21 - 21 (1 bit)
access : read-write
DET6 : PIOBU Intrusion Detector Protection
bits : 22 - 22 (1 bit)
access : read-write
DET7 : PIOBU Intrusion Detector Protection
bits : 23 - 23 (1 bit)
access : read-write
PIO Backup Register
address_offset : 0xB8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PIOBU_AFV : PIOBU Alarm Filter Value
bits : 0 - 3 (4 bit)
access : read-write
PIOBU_RFV : PIOBUx Reset Filter Value
bits : 4 - 7 (4 bit)
access : read-write
OUTPUT : Configure I/O Line in Input/Output
bits : 8 - 8 (1 bit)
access : read-write
PIO_SOD : Set/Clear the I/O Line when configured in Output Mode (OUTPUT =1)
bits : 9 - 9 (1 bit)
access : read-write
PIO_PDS : Level on the Pin in Input Mode (OUTPUT = 0) (Read-only)
bits : 10 - 10 (1 bit)
access : read-write
PULLUP : Programmable Pull-up State
bits : 12 - 13 (2 bit)
access : read-write
SCHEDULE : Pull-up/Down Scheduled
bits : 14 - 14 (1 bit)
access : read-write
SWITCH : Switch State for Intrusion Detection
bits : 15 - 15 (1 bit)
access : read-write
PIO Backup Register
address_offset : 0xE4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PIOBU_AFV : PIOBU Alarm Filter Value
bits : 0 - 3 (4 bit)
access : read-write
PIOBU_RFV : PIOBUx Reset Filter Value
bits : 4 - 7 (4 bit)
access : read-write
OUTPUT : Configure I/O Line in Input/Output
bits : 8 - 8 (1 bit)
access : read-write
PIO_SOD : Set/Clear the I/O Line when configured in Output Mode (OUTPUT =1)
bits : 9 - 9 (1 bit)
access : read-write
PIO_PDS : Level on the Pin in Input Mode (OUTPUT = 0) (Read-only)
bits : 10 - 10 (1 bit)
access : read-write
PULLUP : Programmable Pull-up State
bits : 12 - 13 (2 bit)
access : read-write
SCHEDULE : Pull-up/Down Scheduled
bits : 14 - 14 (1 bit)
access : read-write
SWITCH : Switch State for Intrusion Detection
bits : 15 - 15 (1 bit)
access : read-write
Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !
This website is sponsored by Embeetle, an IDE designed from scratch for embedded software developers.