\n
address_offset : 0x0 Bytes (0x0)
size : 0x3B0 byte (0x0)
mem_usage : registers
protection : not protected
DSPI1_IPP_IND_SCK_SELECT_INPUT
DSPI1_IPP_IND_SIN_SELECT_INPUT
DSPI1_IPP_IND_SS_B_SELECT_INPUT
ENET_SWIAHB_IPP_IND_MAC0_TIMER_0_SELECT_INPUT
ENET_SWIAHB_IPP_IND_MAC0_TIMER_1_SELECT_INPUT
ESAI_IPP_IND_SCKT_SELECT_INPUT
ESAI_IPP_IND_SDO0_SELECT_INPUT
ESAI_IPP_IND_SDO1_SELECT_INPUT
ESAI_IPP_IND_SDO2_SDI3_SELECT_INPUT
ESAI_IPP_IND_SDO3_SDI2_SELECT_INPUT
ESAI_IPP_IND_SDO4_SDI1_SELECT_INPUT
ESAI_IPP_IND_SDO5_SDI0_SELECT_INPUT
FLEXTIMER1_IPP_IND_FTM_CH_0_SELECT_INPUT
FLEXTIMER1_IPP_IND_FTM_CH_1_SELECT_INPUT
FLEXTIMER1_IPP_IND_FTM_PHA_SELECT_INPUT
FLEXTIMER1_IPP_IND_FTM_PHB_SELECT_INPUT
MLB_TOP_MLBCLK_IN_SELECT_INPUT
MLB_TOP_MLBDAT_IN_SELECT_INPUT
MLB_TOP_MLBSIG_IN_SELECT_INPUT
SAI1_IPP_IND_SAI_TXSYNC_SELECT_INPUT
SAI2_IPP_IND_SAI_RXBCLK_SELECT_INPUT
SAI2_IPP_IND_SAI_RXDATA_0_SELECT_INPUT
SAI2_IPP_IND_SAI_RXSYNC_SELECT_INPUT
SAI2_IPP_IND_SAI_TXBCLK_SELECT_INPUT
SAI2_IPP_IND_SAI_TXSYNC_SELECT_INPUT
SCI_FLX1_IPP_IND_CTS_B_SELECT_INPUT
SCI_FLX1_IPP_IND_SCI_RX_SELECT_INPUT
SCI_FLX1_IPP_IND_SCI_TX_SELECT_INPUT
SCI_FLX2_IPP_IND_CTS_B_SELECT_INPUT
SCI_FLX2_IPP_IND_SCI_RX_SELECT_INPUT
SCI_FLX2_IPP_IND_SCI_TX_SELECT_INPUT
SCI_FLX3_IPP_IND_SCI_RX_SELECT_INPUT
SCI_FLX3_IPP_IND_SCI_TX_SELECT_INPUT
SRC_IPP_BOOT_CFG_18_SELECT_INPUT
SRC_IPP_BOOT_CFG_19_SELECT_INPUT
SRC_IPP_BOOT_CFG_20_SELECT_INPUT
VIDEO_IN0_IPP_IND_DE_SELECT_INPUT
VIDEO_IN0_IPP_IND_FID_SELECT_INPUT
VIDEO_IN0_IPP_IND_PIX_CLK_SELECT_INPUT
Software MUX Pad Control Register 0
address_offset : 0x0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 0
address_offset : 0x0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
medium (100MHz)
#10 : 10
medium (100MHz)
#11 : 11
high (200MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[0] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: RMII_CLKOUT of instance: ccm.
#010 : 010
Select mux mode: ALT2 mux port: RMII_CLKIN of instance: ccm. Used as MAC0-TXCLK when MAC0-MII is enabled.
#100 : 100
Select mux mode: ALT4 mux port: TCON[11] of instance: tcon1.
#111 : 111
Select mux mode: ALT7 mux port: DATA_OUT[20] of instance: tcon1.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 4
address_offset : 0x10 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[4] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: TMS of instance: debug.
#100 : 100
Select mux mode: ALT4 mux port: DATA_OUT[11] of instance: tcon0.
#111 : 111
Select mux mode: ALT7 mux port: MLBDATA of instance: mlb_top.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 4
address_offset : 0x10 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 64
address_offset : 0x100 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 64
address_offset : 0x100 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[64] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: FB_AD[30] of instance: platform.
#010 : 010
Select mux mode: ALT2 mux port: NF_IO[14] of instance: nfc_mlc.
#100 : 100
Select mux mode: ALT4 mux port: CH[1] of instance: flextimer3.
#101 : 101
Select mux mode: ALT5 mux port: CS0 of instance: dspi2.
#111 : 111
Select mux mode: ALT7 mux port: debug_out[10] of instance: viu_mux.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 65
address_offset : 0x104 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[65] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: FB_AD[29] of instance: platform.
#010 : 010
Select mux mode: ALT2 mux port: NF_IO[13] of instance: nfc_mlc.
#100 : 100
Select mux mode: ALT4 mux port: CH[2] of instance: flextimer3.
#101 : 101
Select mux mode: ALT5 mux port: SIN of instance: dspi2.
#111 : 111
Select mux mode: ALT7 mux port: debug_out[11] of instance: viu_mux.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 65
address_offset : 0x104 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 66
address_offset : 0x108 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 66
address_offset : 0x108 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[66] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: FB_AD[28] of instance: platform.
#010 : 010
Select mux mode: ALT2 mux port: NF_IO[12] of instance: nfc_mlc.
#011 : 011
Select mux mode: ALT3 mux port: SCL of instance: i2c2.
#100 : 100
Select mux mode: ALT4 mux port: CH[3] of instance: flextimer3.
#101 : 101
Select mux mode: ALT5 mux port: SOUT of instance: dspi2.
#111 : 111
Select mux mode: ALT7 mux port: debug_out[12] of instance: viu_mux.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 67
address_offset : 0x10C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 67
address_offset : 0x10C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[67] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: FB_AD[27] of instance: platform.
#010 : 010
Select mux mode: ALT2 mux port: NF_IO[11] of instance: nfc_mlc.
#011 : 011
Select mux mode: ALT3 mux port: SDA of instance: i2c2.
#100 : 100
Select mux mode: ALT4 mux port: CH[4] of instance: flextimer3.
#101 : 101
Select mux mode: ALT5 mux port: SCK of instance: dspi2.
#111 : 111
Select mux mode: ALT7 mux port: debug_out[13] of instance: viu_mux.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 68
address_offset : 0x110 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 68
address_offset : 0x110 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[68] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: FB_AD[26] of instance: platform.
#010 : 010
Select mux mode: ALT2 mux port: NF_IO[10] of instance: nfc_mlc.
#100 : 100
Select mux mode: ALT4 mux port: CH[5] of instance: flextimer3.
#101 : 101
Select mux mode: ALT5 mux port: WP of instance: esdhc1.
#111 : 111
Select mux mode: ALT7 mux port: debug_out[14] of instance: viu_mux.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 69
address_offset : 0x114 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 69
address_offset : 0x114 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[69] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: FB_AD[25] of instance: platform.
#010 : 010
Select mux mode: ALT2 mux port: NF_IO[9] of instance: nfc_mlc.
#100 : 100
Select mux mode: ALT4 mux port: CH[6] of instance: flextimer3.
#111 : 111
Select mux mode: ALT7 mux port: debug_out[15] of instance: viu_mux.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 70
address_offset : 0x118 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[70] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: FB_AD[24] of instance: platform.
#010 : 010
Select mux mode: ALT2 mux port: NF_IO[8] of instance: nfc_mlc.
#100 : 100
Select mux mode: ALT4 mux port: CH[7] of instance: flextimer3.
#111 : 111
Select mux mode: ALT7 mux port: debug_out[16] of instance: viu_mux.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 70
address_offset : 0x118 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 71
address_offset : 0x11C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[71] of instance: rgpioc. Also, RXDATA[3] for MAC0 is enabled in this mux mode so ensure obe is disabled if this pin is used for MAC0-MII instead of GPIO.
#001 : 001
Select mux mode: ALT1 mux port: FB_AD[23] of instance: platform.
#010 : 010
Select mux mode: ALT2 mux port: NF_IO[7] of instance: nfc_mlc.
#011 : 011
Select mux mode: ALT3 mux port: CH[0] of instance: flextimer2.
#100 : 100
Select mux mode: ALT4 mux port: MAC0_TMR0 of instance: enet_swiahb.
#101 : 101
Select mux mode: ALT5 mux port: DAT4 of instance: esdhc0.
#110 : 110
Select mux mode: ALT6 mux port: TX of instance: sci_flx2.
#111 : 111
Select mux mode: ALT7 mux port: DATA_OUT[21] of instance: tcon1.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 71
address_offset : 0x11C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 72
address_offset : 0x120 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[72] of instance: rgpioc. Also, RXDATA[2] for MAC0 is enabled in this mux mode so ensure obe is disabled if this pin is used for MAC0-MII instead of GPIO.
#001 : 001
Select mux mode: ALT1 mux port: FB_AD[22] of instance: platform.
#010 : 010
Select mux mode: ALT2 mux port: NF_IO[6] of instance: nfc_mlc.
#011 : 011
Select mux mode: ALT3 mux port: CH[1] of instance: flextimer2.
#100 : 100
Select mux mode: ALT4 mux port: MAC0_TMR1 of instance: enet_swiahb.
#101 : 101
Select mux mode: ALT5 mux port: DAT5 of instance: esdhc0.
#110 : 110
Select mux mode: ALT6 mux port: RX of instance: sci_flx2.
#111 : 111
Select mux mode: ALT7 mux port: DATA_OUT[22] of instance: tcon1.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 72
address_offset : 0x120 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 73
address_offset : 0x124 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 73
address_offset : 0x124 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[73] of instance: rgpioc. Also, CRS for MAC0 is enabled in this mux mode so ensure obe is disabled if this pin is used for MAC0-MII instead of GPIO.
#001 : 001
Select mux mode: ALT1 mux port: FB_AD[21] of instance: platform.
#010 : 010
Select mux mode: ALT2 mux port: NF_IO[5] of instance: nfc_mlc.
#100 : 100
Select mux mode: ALT4 mux port: MAC0_TMR2 of instance: enet_swiahb.
#101 : 101
Select mux mode: ALT5 mux port: DAT6 of instance: esdhc0.
#110 : 110
Select mux mode: ALT6 mux port: RTS of instance: sci_flx2.
#111 : 111
Select mux mode: ALT7 mux port: DATA_OUT[23] of instance: tcon1.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 74
address_offset : 0x128 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 74
address_offset : 0x128 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[74] of instance: rgpioc. Also, COL for MAC0 is enabled in this mux mode so ensure obe is disabled if this pin is used for MAC0-MII instead of GPIO.
#001 : 001
Select mux mode: ALT1 mux port: FB_AD[20] of instance: platform.
#010 : 010
Select mux mode: ALT2 mux port: NF_IO[4] of instance: nfc_mlc.
#100 : 100
Select mux mode: ALT4 mux port: MAC0_TMR3 of instance: enet_swiahb.
#101 : 101
Select mux mode: ALT5 mux port: DAT7 of instance: esdhc0.
#110 : 110
Select mux mode: ALT6 mux port: CTS of instance: sci_flx2.
#111 : 111
Select mux mode: ALT7 mux port: DATA_OUT[18] of instance: tcon1.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 75
address_offset : 0x12C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[75] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: FB_AD[19] of instance: platform.
#010 : 010
Select mux mode: ALT2 mux port: NF_IO[3] of instance: nfc_mlc.
#011 : 011
Select mux mode: ALT3 mux port: SCKR of instance: esai.
#100 : 100
Select mux mode: ALT4 mux port: SCL of instance: i2c0.
#101 : 101
Select mux mode: ALT5 mux port: QD_PHA of instance: flextimer2.
#110 : 110
Select mux mode: ALT6 mux port: TXDATA[3] for MAC0-MII
#111 : 111
Select mux mode: ALT7 mux port: DATA_OUT[19] of instance: tcon1.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 75
address_offset : 0x12C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 76
address_offset : 0x130 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[76] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: FB_AD[18] of instance: platform.
#010 : 010
Select mux mode: ALT2 mux port: NF_IO[2] of instance: nfc_mlc.
#011 : 011
Select mux mode: ALT3 mux port: FSR of instance: esai.
#100 : 100
Select mux mode: ALT4 mux port: SDA of instance: i2c0.
#101 : 101
Select mux mode: ALT5 mux port: QD_PHB of instance: flextimer2.
#111 : 111
Select mux mode: ALT7 mux port: DATA_OUT[10] of instance: tcon1.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 76
address_offset : 0x130 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 77
address_offset : 0x134 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 77
address_offset : 0x134 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[77] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: FB_AD[17] of instance: platform.
#010 : 010
Select mux mode: ALT2 mux port: NF_IO[1] of instance: nfc_mlc.
#011 : 011
Select mux mode: ALT3 mux port: HCKR of instance: esai.
#100 : 100
Select mux mode: ALT4 mux port: SCL of instance: i2c1.
#110 : 110
Select mux mode: ALT6 mux port: TXERR of MAC0-MII
#111 : 111
Select mux mode: ALT7 mux port: DATA_OUT[11] of instance: tcon1.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 78
address_offset : 0x138 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 78
address_offset : 0x138 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[78] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: FB_AD[16] of instance: platform.
#010 : 010
Select mux mode: ALT2 mux port: NF_IO[0] of instance: nfc_mlc.
#011 : 011
Select mux mode: ALT3 mux port: HCKT of instance: esai.
#100 : 100
Select mux mode: ALT4 mux port: SDA of instance: i2c1.
#111 : 111
Select mux mode: ALT7 mux port: DATA_OUT[12] of instance: tcon1.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 79
address_offset : 0x13C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 79
address_offset : 0x13C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[79] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: QSCK_A of instance: quadspi0.
#010 : 010
Select mux mode: ALT2 mux port: TX of instance: sci_flx2.
#100 : 100
Select mux mode: ALT4 mux port: FB_AD[15] of instance: platform.
#101 : 101
Select mux mode: ALT5 mux port: EXTCLK of instance: spdif.
#111 : 111
Select mux mode: ALT7 mux port: debug_out[17] of instance: viu_mux.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 5
address_offset : 0x14 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[5] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: TRACECK of instance: platform.
#010 : 010
Select mux mode: ALT2 mux port: EXT_AUDIO_MCLK of instance: ccm.
#110 : 110
Select mux mode: ALT6 mux port: DATA[13] of instance: video_in0.
#111 : 111
Select mux mode: ALT7 mux port: SCL of instance: i2c0.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 5
address_offset : 0x14 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 80
address_offset : 0x140 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 80
address_offset : 0x140 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[80] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: QPCS0_A of instance: quadspi0.
#010 : 010
Select mux mode: ALT2 mux port: RX of instance: sci_flx2.
#100 : 100
Select mux mode: ALT4 mux port: FB_AD[14] of instance: platform.
#101 : 101
Select mux mode: ALT5 mux port: IN1 of instance: spdif.
#111 : 111
Select mux mode: ALT7 mux port: debug_out[18] of instance: viu_mux.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 81
address_offset : 0x144 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 81
address_offset : 0x144 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[81] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: QSPI_IO3_A of instance: quadspi0.
#010 : 010
Select mux mode: ALT2 mux port: RTS of instance: sci_flx2.
#011 : 011
Select mux mode: ALT3 mux port: CS3 of instance: dspi1.
#100 : 100
Select mux mode: ALT4 mux port: FB_AD[13] of instance: platform.
#101 : 101
Select mux mode: ALT5 mux port: OUT1 of instance: spdif.
#111 : 111
Select mux mode: ALT7 mux port: debug_out[19] of instance: viu_mux.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 82
address_offset : 0x148 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[82] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: QSPI_IO2_A of instance: quadspi0.
#010 : 010
Select mux mode: ALT2 mux port: CTS of instance: sci_flx2.
#011 : 011
Select mux mode: ALT3 mux port: CS2 of instance: dspi1.
#100 : 100
Select mux mode: ALT4 mux port: FB_AD[12] of instance: platform.
#101 : 101
Select mux mode: ALT5 mux port: PLOCK of instance: spdif.
#111 : 111
Select mux mode: ALT7 mux port: debug_out[20] of instance: viu_mux.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 82
address_offset : 0x148 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 83
address_offset : 0x14C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 83
address_offset : 0x14C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[83] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: QSPI_IO1_A of instance: quadspi0.
#011 : 011
Select mux mode: ALT3 mux port: CS1 of instance: dspi1.
#100 : 100
Select mux mode: ALT4 mux port: FB_AD[11] of instance: platform.
#101 : 101
Select mux mode: ALT5 mux port: SRCLK of instance: spdif.
#111 : 111
Select mux mode: ALT7 mux port: debug_out[21] of instance: viu_mux.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 84
address_offset : 0x150 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[84] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: QSPI_IO0_A of instance: quadspi0.
#011 : 011
Select mux mode: ALT3 mux port: CS0 of instance: dspi1.
#100 : 100
Select mux mode: ALT4 mux port: FB_AD[10] of instance: platform.
#111 : 111
Select mux mode: ALT7 mux port: debug_out[22] of instance: viu_mux.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 84
address_offset : 0x150 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 85
address_offset : 0x154 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 85
address_offset : 0x154 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[85] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: DQS_A of instance: quadspi0.
#011 : 011
Select mux mode: ALT3 mux port: SIN of instance: dspi1.
#100 : 100
Select mux mode: ALT4 mux port: FB_AD[9] of instance: platform.
#111 : 111
Select mux mode: ALT7 mux port: debug_out[23] of instance: viu_mux.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 86
address_offset : 0x158 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 86
address_offset : 0x158 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[86] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: QSCK_B of instance: quadspi0.
#011 : 011
Select mux mode: ALT3 mux port: SOUT of instance: dspi1.
#100 : 100
Select mux mode: ALT4 mux port: FB_AD[8] of instance: platform.
#111 : 111
Select mux mode: ALT7 mux port: debug_out[24] of instance: viu_mux.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 87
address_offset : 0x15C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[87] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: QPCS0_B of instance: quadspi0.
#010 : 010
Select mux mode: ALT2 mux port: FB_CLKOUT of instance: lpcg0.
#011 : 011
Select mux mode: ALT3 mux port: SCK of instance: dspi1.
#100 : 100
Select mux mode: ALT4 mux port: FB_AD[7] of instance: platform.
#111 : 111
Select mux mode: ALT7 mux port: debug_out[25] of instance: viu_mux.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 87
address_offset : 0x15C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 88
address_offset : 0x160 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[88] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: QSPI_IO3_B of instance: quadspi0.
#010 : 010
Select mux mode: ALT2 mux port: CS1 of instance: dspi3.
#100 : 100
Select mux mode: ALT4 mux port: FB_AD[6] of instance: platform.
#110 : 110
Select mux mode: ALT6 mux port: TX_SYNC of instance: sai1.
#111 : 111
Select mux mode: ALT7 mux port: DATA_OUT[2] of instance: tcon1.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 88
address_offset : 0x160 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 89
address_offset : 0x164 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 89
address_offset : 0x164 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[89] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: QSPI_IO2_B of instance: quadspi0.
#010 : 010
Select mux mode: ALT2 mux port: CS0 of instance: dspi3.
#100 : 100
Select mux mode: ALT4 mux port: FB_AD[5] of instance: platform.
#111 : 111
Select mux mode: ALT7 mux port: DATA_OUT[3] of instance: tcon1.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 90
address_offset : 0x168 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 90
address_offset : 0x168 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[90] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: QSPI_IO1_B of instance: quadspi0.
#010 : 010
Select mux mode: ALT2 mux port: SIN of instance: dspi3.
#100 : 100
Select mux mode: ALT4 mux port: FB_AD[4] of instance: platform.
#111 : 111
Select mux mode: ALT7 mux port: debug_out[26] of instance: viu_mux.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 91
address_offset : 0x16C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 91
address_offset : 0x16C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[91] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: QSPI_IO0_B of instance: quadspi0.
#010 : 010
Select mux mode: ALT2 mux port: SOUT of instance: dspi3.
#100 : 100
Select mux mode: ALT4 mux port: FB_AD[3] of instance: platform.
#111 : 111
Select mux mode: ALT7 mux port: debug_out[27] of instance: viu_mux.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 92
address_offset : 0x170 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 92
address_offset : 0x170 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[92] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: DQS_B of instance: quadspi0.
#010 : 010
Select mux mode: ALT2 mux port: SCK of instance: dspi3.
#100 : 100
Select mux mode: ALT4 mux port: FB_AD[2] of instance: platform.
#111 : 111
Select mux mode: ALT7 mux port: debug_out[28] of instance: viu_mux.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 93
address_offset : 0x174 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 93
address_offset : 0x174 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[93] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: TX_BCLK of instance: sai0.
#010 : 010
Select mux mode: ALT2 mux port: TX of instance: sci_flx1.
#100 : 100
Select mux mode: ALT4 mux port: FB_MUXED_ALE of instance: platform.
#101 : 101
Select mux mode: ALT5 mux port: FB_TS_b of instance: platform.
#110 : 110
Select mux mode: ALT6 mux port: RTS of instance: sci_flx3.
#111 : 111
Select mux mode: ALT7 mux port: DATA_OUT[13] of instance: tcon1.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 94
address_offset : 0x178 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[94] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: RX_BCLK of instance: sai0.
#010 : 010
Select mux mode: ALT2 mux port: RX of instance: sci_flx1.
#100 : 100
Select mux mode: ALT4 mux port: FB_MUXED_TSIZ0 of instance: platform.
#101 : 101
Select mux mode: ALT5 mux port: NF_WE_b of instance: nfc_mlc.
#110 : 110
Select mux mode: ALT6 mux port: CTS of instance: sci_flx3.
#111 : 111
Select mux mode: ALT7 mux port: DATA_OUT[14] of instance: tcon1.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 94
address_offset : 0x178 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 95
address_offset : 0x17C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[95] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: RX_DATA of instance: sai0.
#010 : 010
Select mux mode: ALT2 mux port: RTS of instance: sci_flx1.
#100 : 100
Select mux mode: ALT4 mux port: FB_CS1_b of instance: platform.
#101 : 101
Select mux mode: ALT5 mux port: NF_CE0_b of instance: nfc_mlc.
#111 : 111
Select mux mode: ALT7 mux port: DATA_OUT[15] of instance: tcon1.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 95
address_offset : 0x17C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 6
address_offset : 0x18 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[6] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: TRACED[0] of instance: platform.
#010 : 010
Select mux mode: ALT2 mux port: VBUS_EN_OTG of instance: usb.
#011 : 011
Select mux mode: ALT3 mux port: ADC1SE0 of instance: adc1_da.
#100 : 100
Select mux mode: ALT4 mux port: LCD29 of instance: lcd_64f6b.
#101 : 101
Select mux mode: ALT5 mux port: TX_BCLK of instance: sai2.
#110 : 110
Select mux mode: ALT6 mux port: DATA[14] of instance: video_in0.
#111 : 111
Select mux mode: ALT7 mux port: SDA of instance: i2c0.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 6
address_offset : 0x18 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 96
address_offset : 0x180 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 96
address_offset : 0x180 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[96] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: TX_DATA of instance: sai0.
#010 : 010
Select mux mode: ALT2 mux port: CTS of instance: sci_flx1.
#011 : 011
Select mux mode: ALT3 mux port: RCON21 of instance: src.
#100 : 100
Select mux mode: ALT4 mux port: FB_CS0_b of instance: platform.
#101 : 101
Select mux mode: ALT5 mux port: NF_CE1_b of instance: nfc_mlc.
#111 : 111
Select mux mode: ALT7 mux port: DATA_OUT[16] of instance: tcon1.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 97
address_offset : 0x184 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[97] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: RX_SYNC of instance: sai0.
#011 : 011
Select mux mode: ALT3 mux port: RCON22 of instance: src.
#100 : 100
Select mux mode: ALT4 mux port: FB_OE_b of instance: platform.
#101 : 101
Select mux mode: ALT5 mux port: FB_MUXED_TBST_b of instance: platform.
#110 : 110
Select mux mode: ALT6 mux port: NF_RE_b of instance: nfc_mlc.
#111 : 111
Select mux mode: ALT7 mux port: DATA_OUT[17] of instance: tcon1.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 97
address_offset : 0x184 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 98
address_offset : 0x188 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 98
address_offset : 0x188 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[98] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: TX_SYNC of instance: sai0.
#011 : 011
Select mux mode: ALT3 mux port: RCON23 of instance: src.
#100 : 100
Select mux mode: ALT4 mux port: FB_RW_b of instance: platform.
#111 : 111
Select mux mode: ALT7 mux port: DATA_OUT[8] of instance: tcon1.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 99
address_offset : 0x18C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 99
address_offset : 0x18C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[99] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: TX_BCLK of instance: sai1.
#010 : 010
Select mux mode: ALT2 mux port: CS5 of instance: dspi0.
#011 : 011
Select mux mode: ALT3 mux port: RCON24 of instance: src.
#100 : 100
Select mux mode: ALT4 mux port: FB_TA_b of instance: platform.
#101 : 101
Select mux mode: ALT5 mux port: NF_RB_b of instance: nfc_mlc.
#111 : 111
Select mux mode: ALT7 mux port: DATA_OUT[9] of instance: tcon1.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 100
address_offset : 0x190 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 100
address_offset : 0x190 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[100] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: RX_BCLK of instance: sai1.
#010 : 010
Select mux mode: ALT2 mux port: CS4 of instance: dspi0.
#011 : 011
Select mux mode: ALT3 mux port: RCON25 of instance: src.
#100 : 100
Select mux mode: ALT4 mux port: FB_BE3_b of instance: platform.
#101 : 101
Select mux mode: ALT5 mux port: FB_CS3_b of instance: platform.
#110 : 110
Select mux mode: ALT6 mux port: NF_ALE of instance: nfc_mlc.
#111 : 111
Select mux mode: ALT7 mux port: DATA_OUT[4] of instance: tcon1.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 101
address_offset : 0x194 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[101] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: RX_DATA of instance: sai1.
#010 : 010
Select mux mode: ALT2 mux port: CS3 of instance: dspi0.
#011 : 011
Select mux mode: ALT3 mux port: RCON26 of instance: src.
#100 : 100
Select mux mode: ALT4 mux port: FB_BE2_b of instance: platform.
#101 : 101
Select mux mode: ALT5 mux port: FB_CS2_b of instance: platform.
#110 : 110
Select mux mode: ALT6 mux port: NF_CLE of instance: nfc_mlc.
#111 : 111
Select mux mode: ALT7 mux port: DATA_OUT[5] of instance: tcon1.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 101
address_offset : 0x194 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 102
address_offset : 0x198 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 102
address_offset : 0x198 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[102] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: TX_DATA of instance: sai1.
#010 : 010
Select mux mode: ALT2 mux port: CS2 of instance: dspi0.
#011 : 011
Select mux mode: ALT3 mux port: RCON27 of instance: src.
#100 : 100
Select mux mode: ALT4 mux port: FB_BE1_b of instance: platform.
#101 : 101
Select mux mode: ALT5 mux port: FB_MUXED_TSIZ1 of instance: platform.
#111 : 111
Select mux mode: ALT7 mux port: DATA_OUT[6] of instance: tcon1.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 103
address_offset : 0x19C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 103
address_offset : 0x19C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[103] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: RX_SYNC of instance: sai1.
#010 : 010
Select mux mode: ALT2 mux port: CS2 of instance: dspi1.
#011 : 011
Select mux mode: ALT3 mux port: RCON28 of instance: src.
#100 : 100
Select mux mode: ALT4 mux port: FB_MUXED_BE0_b of instance: platform.
#101 : 101
Select mux mode: ALT5 mux port: FB_TSIZ0 of instance: platform.
#110 : 110
Select mux mode: ALT6 mux port: ADC0SE5 of instance: adc0_da.
#111 : 111
Select mux mode: ALT7 mux port: DATA_OUT[7] of instance: tcon1.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 104
address_offset : 0x1A0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 104
address_offset : 0x1A0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[104] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: TX_SYNC of instance: sai1.
#011 : 011
Select mux mode: ALT3 mux port: RCON29 of instance: src.
#110 : 110
Select mux mode: ALT6 mux port: ADC1SE5 of instance: adc1_da.
#111 : 111
Select mux mode: ALT7 mux port: DATA_OUT[8] of instance: tcon1.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 105
address_offset : 0x1A4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[105] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: TCON[1] of instance: tcon0.
#010 : 010
Select mux mode: ALT2 mux port: BOOTMODE[1] of instance: src.
#100 : 100
Select mux mode: ALT4 mux port: LCD0 of instance: lcd_64f6b.
#111 : 111
Select mux mode: ALT7 mux port: debug_out[29] of instance: viu_mux.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 105
address_offset : 0x1A4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 106
address_offset : 0x1A8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[106] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: TCON[2] of instance: tcon0.
#010 : 010
Select mux mode: ALT2 mux port: BOOTMODE[0] of instance: src.
#100 : 100
Select mux mode: ALT4 mux port: LCD1 of instance: lcd_64f6b.
#111 : 111
Select mux mode: ALT7 mux port: debug_out[30] of instance: viu_mux.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 106
address_offset : 0x1A8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 107
address_offset : 0x1AC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 107
address_offset : 0x1AC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[107] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: DATA_OUT[1] of instance: tcon0.
#100 : 100
Select mux mode: ALT4 mux port: LCD2 of instance: lcd_64f6b.
#111 : 111
Select mux mode: ALT7 mux port: debug_out[31] of instance: viu_mux.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 108
address_offset : 0x1B0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 108
address_offset : 0x1B0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[108] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: TCON[0] of instance: tcon0.
#100 : 100
Select mux mode: ALT4 mux port: LCD3 of instance: lcd_64f6b.
#111 : 111
Select mux mode: ALT7 mux port: debug_out[32] of instance: viu_mux.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 109
address_offset : 0x1B4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 109
address_offset : 0x1B4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[109] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: TCON[3] of instance: tcon0.
#100 : 100
Select mux mode: ALT4 mux port: LCD4 of instance: lcd_64f6b.
#111 : 111
Select mux mode: ALT7 mux port: debug_out[33] of instance: viu_mux.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 110
address_offset : 0x1B8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 110
address_offset : 0x1B8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[110] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: DATA_OUT[18] of instance: tcon0.
#100 : 100
Select mux mode: ALT4 mux port: LCD5 of instance: lcd_64f6b.
#111 : 111
Select mux mode: ALT7 mux port: debug_out[34] of instance: viu_mux.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 111
address_offset : 0x1BC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[111] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: DATA_OUT[19] of instance: tcon0.
#100 : 100
Select mux mode: ALT4 mux port: LCD6 of instance: lcd_64f6b.
#111 : 111
Select mux mode: ALT7 mux port: debug_out[35] of instance: viu_mux.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 111
address_offset : 0x1BC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 7
address_offset : 0x1C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[7] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: TRACED[1] of instance: platform.
#010 : 010
Select mux mode: ALT2 mux port: VBUS_OC_OTG of instance: usb.
#011 : 011
Select mux mode: ALT3 mux port: ADC1SE1 of instance: adc1_da.
#100 : 100
Select mux mode: ALT4 mux port: LCD30 of instance: lcd_64f6b.
#101 : 101
Select mux mode: ALT5 mux port: USB0_SOF_PULSE of instance: usb.
#110 : 110
Select mux mode: ALT6 mux port: DATA[15] of instance: video_in0.
#111 : 111
Select mux mode: ALT7 mux port: SCL of instance: i2c1.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 7
address_offset : 0x1C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 112
address_offset : 0x1C0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[112] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: DATA_OUT[20] of instance: tcon0.
#011 : 011
Select mux mode: ALT3 mux port: RCON0 of instance: src.
#100 : 100
Select mux mode: ALT4 mux port: LCD7 of instance: lcd_64f6b.
#111 : 111
Select mux mode: ALT7 mux port: debug_out[36] of instance: viu_mux.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 112
address_offset : 0x1C0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 113
address_offset : 0x1C4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[113] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: DATA_OUT[21] of instance: tcon0.
#011 : 011
Select mux mode: ALT3 mux port: RCON1 of instance: src.
#100 : 100
Select mux mode: ALT4 mux port: LCD8 of instance: lcd_64f6b.
#111 : 111
Select mux mode: ALT7 mux port: debug_out[37] of instance: viu_mux.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 113
address_offset : 0x1C4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 114
address_offset : 0x1C8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[114] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: DATA_OUT[22] of instance: tcon0.
#011 : 011
Select mux mode: ALT3 mux port: RCON2 of instance: src.
#100 : 100
Select mux mode: ALT4 mux port: LCD9 of instance: lcd_64f6b.
#111 : 111
Select mux mode: ALT7 mux port: debug_out[38] of instance: viu_mux.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 114
address_offset : 0x1C8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 115
address_offset : 0x1CC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 115
address_offset : 0x1CC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[115] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: DATA_OUT[23] of instance: tcon0.
#011 : 011
Select mux mode: ALT3 mux port: RCON3 of instance: src.
#100 : 100
Select mux mode: ALT4 mux port: LCD10 of instance: lcd_64f6b.
#111 : 111
Select mux mode: ALT7 mux port: debug_out[39] of instance: viu_mux.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 116
address_offset : 0x1D0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 116
address_offset : 0x1D0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[116] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: DATA_OUT[24] of instance: tcon0.
#011 : 011
Select mux mode: ALT3 mux port: RCON4 of instance: src.
#100 : 100
Select mux mode: ALT4 mux port: LCD11 of instance: lcd_64f6b.
#111 : 111
Select mux mode: ALT7 mux port: debug_out[40] of instance: viu_mux.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 117
address_offset : 0x1D4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[117] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: DATA_OUT[25] of instance: tcon0.
#010 : 010
Select mux mode: ALT2 mux port: CS3 of instance: dspi1.
#011 : 011
Select mux mode: ALT3 mux port: RCON5 of instance: src.
#100 : 100
Select mux mode: ALT4 mux port: LCD12 of instance: lcd_64f6b.
#111 : 111
Select mux mode: ALT7 mux port: LP_IN of instance: lptimer.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 117
address_offset : 0x1D4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 118
address_offset : 0x1D8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[118] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: DATA_OUT[10] of instance: tcon0.
#100 : 100
Select mux mode: ALT4 mux port: LCD13 of instance: lcd_64f6b.
#111 : 111
Select mux mode: ALT7 mux port: debug_out[41] of instance: viu_mux.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 118
address_offset : 0x1D8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 119
address_offset : 0x1DC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[119] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: DATA_OUT[11] of instance: tcon0.
#100 : 100
Select mux mode: ALT4 mux port: LCD14 of instance: lcd_64f6b.
#111 : 111
Select mux mode: ALT7 mux port: debug_out[42] of instance: viu_mux.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 119
address_offset : 0x1DC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 120
address_offset : 0x1E0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[120] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: DATA_OUT[12] of instance: tcon0.
#011 : 011
Select mux mode: ALT3 mux port: RCON6 of instance: src.
#100 : 100
Select mux mode: ALT4 mux port: LCD15 of instance: lcd_64f6b.
#111 : 111
Select mux mode: ALT7 mux port: debug_out[43] of instance: viu_mux.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 120
address_offset : 0x1E0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 121
address_offset : 0x1E4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 121
address_offset : 0x1E4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[121] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: DATA_OUT[13] of instance: tcon0.
#011 : 011
Select mux mode: ALT3 mux port: RCON7 of instance: src.
#100 : 100
Select mux mode: ALT4 mux port: LCD16 of instance: lcd_64f6b.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 122
address_offset : 0x1E8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[122] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: DATA_OUT[14] of instance: tcon0.
#011 : 011
Select mux mode: ALT3 mux port: RCON8 of instance: src.
#100 : 100
Select mux mode: ALT4 mux port: LCD17 of instance: lcd_64f6b.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 122
address_offset : 0x1E8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 123
address_offset : 0x1EC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[123] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: DATA_OUT[15] of instance: tcon0.
#011 : 011
Select mux mode: ALT3 mux port: RCON9 of instance: src.
#100 : 100
Select mux mode: ALT4 mux port: LCD18 of instance: lcd_64f6b.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 123
address_offset : 0x1EC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 124
address_offset : 0x1F0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[124] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: DATA_OUT[16] of instance: tcon0.
#011 : 011
Select mux mode: ALT3 mux port: RCON10 of instance: src.
#100 : 100
Select mux mode: ALT4 mux port: LCD19 of instance: lcd_64f6b.
#101 : 101
Select mux mode: ALT5 mux port: SCL of instance: i2c0.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 124
address_offset : 0x1F0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 125
address_offset : 0x1F4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[125] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: DATA_OUT[17] of instance: tcon0.
#011 : 011
Select mux mode: ALT3 mux port: RCON11 of instance: src.
#100 : 100
Select mux mode: ALT4 mux port: LCD20 of instance: lcd_64f6b.
#101 : 101
Select mux mode: ALT5 mux port: SDA of instance: i2c0.
#111 : 111
Select mux mode: ALT7 mux port: in of instance: ewm.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 125
address_offset : 0x1F4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 126
address_offset : 0x1F8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[126] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: DATA_OUT[2] of instance: tcon0.
#100 : 100
Select mux mode: ALT4 mux port: LCD21 of instance: lcd_64f6b.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 126
address_offset : 0x1F8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 127
address_offset : 0x1FC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 127
address_offset : 0x1FC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[127] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: DATA_OUT[3] of instance: tcon0.
#100 : 100
Select mux mode: ALT4 mux port: LCD22 of instance: lcd_64f6b.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 8
address_offset : 0x20 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 8
address_offset : 0x20 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[8] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: TRACED[2] of instance: platform.
#010 : 010
Select mux mode: ALT2 mux port: ADC0SE0 of instance: adc0_da.
#011 : 011
Select mux mode: ALT3 mux port: QD_PHA of instance: flextimer1.
#100 : 100
Select mux mode: ALT4 mux port: LCD31 of instance: lcd_64f6b.
#101 : 101
Select mux mode: ALT5 mux port: TX_DATA of instance: sai2.
#110 : 110
Select mux mode: ALT6 mux port: DATA[16] of instance: video_in0.
#111 : 111
Select mux mode: ALT7 mux port: SDA of instance: i2c1.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 128
address_offset : 0x200 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[128] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: DATA_OUT[4] of instance: tcon0.
#011 : 011
Select mux mode: ALT3 mux port: RCON12 of instance: src.
#100 : 100
Select mux mode: ALT4 mux port: LCD23 of instance: lcd_64f6b.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 128
address_offset : 0x200 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 129
address_offset : 0x204 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[129] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: DATA_OUT[5] of instance: tcon0.
#011 : 011
Select mux mode: ALT3 mux port: RCON13 of instance: src.
#100 : 100
Select mux mode: ALT4 mux port: LCD24 of instance: lcd_64f6b.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 129
address_offset : 0x204 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 130
address_offset : 0x208 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[130] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: DATA_OUT[6] of instance: tcon0.
#011 : 011
Select mux mode: ALT3 mux port: RCON14 of instance: src.
#100 : 100
Select mux mode: ALT4 mux port: LCD25 of instance: lcd_64f6b.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 130
address_offset : 0x208 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 131
address_offset : 0x20C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[131] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: DATA_OUT[7] of instance: tcon0.
#011 : 011
Select mux mode: ALT3 mux port: RCON15 of instance: src.
#100 : 100
Select mux mode: ALT4 mux port: LCD26 of instance: lcd_64f6b.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 131
address_offset : 0x20C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 132
address_offset : 0x210 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[132] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: DATA_OUT[8] of instance: tcon0.
#011 : 011
Select mux mode: ALT3 mux port: RCON16 of instance: src.
#100 : 100
Select mux mode: ALT4 mux port: LCD27 of instance: lcd_64f6b.
#101 : 101
Select mux mode: ALT5 mux port: SCL of instance: i2c1.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 132
address_offset : 0x210 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 133
address_offset : 0x214 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 133
address_offset : 0x214 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[133] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: DATA_OUT[9] of instance: tcon0.
#011 : 011
Select mux mode: ALT3 mux port: RCON17 of instance: src.
#100 : 100
Select mux mode: ALT4 mux port: LCD28 of instance: lcd_64f6b.
#101 : 101
Select mux mode: ALT5 mux port: SDA of instance: i2c1.
#111 : 111
Select mux mode: ALT7 mux port: out of instance: ewm.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 134
address_offset : 0x218 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#00 : 00
Select mux mode: ALT0 mux port: GPIO[134] of instance: rgpioc.
#01 : 01
Select mux mode: ALT1 mux port: PIX_CLK of instance: video_in0.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 134
address_offset : 0x218 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX DDR RESET Pad Configuration Register
address_offset : 0x21C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RESERVED : no description available
bits : 0 - 1 (2 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
RESERVED : no description available
bits : 10 - 13 (4 bit)
access : read-write
DDR_TRIM : no description available
bits : 14 - 15 (2 bit)
access : read-write
Enumeration:
#00 : 00
Minimum do->pad delay
#01 : 01
50 ps do->pad delay
#10 : 10
100 ps do->pad delay
#11 : 11
150 ps do->pad delay
End of enumeration elements list.
DDR_INPUT : no description available
bits : 16 - 16 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input type
#1 : 1
Differential input mode
End of enumeration elements list.
RESERVED : no description available
bits : 17 - 31 (15 bit)
access : read-write
Software MUX DDR A15 Pad Control Register
address_offset : 0x220 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RESERVED : no description available
bits : 0 - 1 (2 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
RESERVED : no description available
bits : 10 - 13 (4 bit)
access : read-write
DDR_TRIM : no description available
bits : 14 - 15 (2 bit)
access : read-write
Enumeration:
#00 : 00
Minimum do->pad delay
#01 : 01
50 ps do->pad delay
#10 : 10
100 ps do->pad delay
#11 : 11
150 ps do->pad delay
End of enumeration elements list.
DDR_INPUT : no description available
bits : 16 - 16 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input type
#1 : 1
Differential input mode
End of enumeration elements list.
RESERVED : no description available
bits : 17 - 31 (15 bit)
access : read-write
Software MUX DDR A14 Pad Control Register
address_offset : 0x224 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RESERVED : no description available
bits : 0 - 1 (2 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
RESERVED : no description available
bits : 10 - 13 (4 bit)
access : read-write
DDR_TRIM : no description available
bits : 14 - 15 (2 bit)
access : read-write
Enumeration:
#00 : 00
Minimum do->pad delay
#01 : 01
50 ps do->pad delay
#10 : 10
100 ps do->pad delay
#11 : 11
150 ps do->pad delay
End of enumeration elements list.
DDR_INPUT : no description available
bits : 16 - 16 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input type
#1 : 1
Differential input mode
End of enumeration elements list.
RESERVED : no description available
bits : 17 - 31 (15 bit)
access : read-write
Software MUX DDR A13 Pad Control Register
address_offset : 0x228 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RESERVED : no description available
bits : 0 - 1 (2 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
RESERVED : no description available
bits : 10 - 13 (4 bit)
access : read-write
DDR_TRIM : no description available
bits : 14 - 15 (2 bit)
access : read-write
Enumeration:
#00 : 00
Minimum do->pad delay
#01 : 01
50 ps do->pad delay
#10 : 10
100 ps do->pad delay
#11 : 11
150 ps do->pad delay
End of enumeration elements list.
DDR_INPUT : no description available
bits : 16 - 16 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input type
#1 : 1
Differential input mode
End of enumeration elements list.
RESERVED : no description available
bits : 17 - 31 (15 bit)
access : read-write
Software MUX DDR A12 Pad Control Register
address_offset : 0x22C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RESERVED : no description available
bits : 0 - 1 (2 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
RESERVED : no description available
bits : 10 - 13 (4 bit)
access : read-write
DDR_TRIM : no description available
bits : 14 - 15 (2 bit)
access : read-write
Enumeration:
#00 : 00
Minimum do->pad delay
#01 : 01
50 ps do->pad delay
#10 : 10
100 ps do->pad delay
#11 : 11
150 ps do->pad delay
End of enumeration elements list.
DDR_INPUT : no description available
bits : 16 - 16 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input type
#1 : 1
Differential input mode
End of enumeration elements list.
RESERVED : no description available
bits : 17 - 31 (15 bit)
access : read-write
Software MUX DDR A11 Pad Control Register
address_offset : 0x230 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RESERVED : no description available
bits : 0 - 1 (2 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
RESERVED : no description available
bits : 10 - 13 (4 bit)
access : read-write
DDR_TRIM : no description available
bits : 14 - 15 (2 bit)
access : read-write
Enumeration:
#00 : 00
Minimum do->pad delay
#01 : 01
50 ps do->pad delay
#10 : 10
100 ps do->pad delay
#11 : 11
150 ps do->pad delay
End of enumeration elements list.
DDR_INPUT : no description available
bits : 16 - 16 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input type
#1 : 1
Differential input mode
End of enumeration elements list.
RESERVED : no description available
bits : 17 - 31 (15 bit)
access : read-write
Software MUX DDR A10 Pad Control Register
address_offset : 0x234 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RESERVED : no description available
bits : 0 - 1 (2 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
RESERVED : no description available
bits : 10 - 13 (4 bit)
access : read-write
DDR_TRIM : no description available
bits : 14 - 15 (2 bit)
access : read-write
Enumeration:
#00 : 00
Minimum do->pad delay
#01 : 01
50 ps do->pad delay
#10 : 10
100 ps do->pad delay
#11 : 11
150 ps do->pad delay
End of enumeration elements list.
DDR_INPUT : no description available
bits : 16 - 16 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input type
#1 : 1
Differential input mode
End of enumeration elements list.
RESERVED : no description available
bits : 17 - 31 (15 bit)
access : read-write
Software MUX DDR A9 Pad Control Register
address_offset : 0x238 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RESERVED : no description available
bits : 0 - 1 (2 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
RESERVED : no description available
bits : 10 - 13 (4 bit)
access : read-write
DDR_TRIM : no description available
bits : 14 - 15 (2 bit)
access : read-write
Enumeration:
#00 : 00
Minimum do->pad delay
#01 : 01
50 ps do->pad delay
#10 : 10
100 ps do->pad delay
#11 : 11
150 ps do->pad delay
End of enumeration elements list.
DDR_INPUT : no description available
bits : 16 - 16 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input type
#1 : 1
Differential input mode
End of enumeration elements list.
RESERVED : no description available
bits : 17 - 31 (15 bit)
access : read-write
Software MUX DDR A8 Pad Control Register
address_offset : 0x23C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RESERVED : no description available
bits : 0 - 1 (2 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
RESERVED : no description available
bits : 10 - 13 (4 bit)
access : read-write
DDR_TRIM : no description available
bits : 14 - 15 (2 bit)
access : read-write
Enumeration:
#00 : 00
Minimum do->pad delay
#01 : 01
50 ps do->pad delay
#10 : 10
100 ps do->pad delay
#11 : 11
150 ps do->pad delay
End of enumeration elements list.
DDR_INPUT : no description available
bits : 16 - 16 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input type
#1 : 1
Differential input mode
End of enumeration elements list.
RESERVED : no description available
bits : 17 - 31 (15 bit)
access : read-write
Software MUX Pad Control Register 9
address_offset : 0x24 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[9] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: TRACED[3] of instance: platform.
#010 : 010
Select mux mode: ALT2 mux port: ADC0SE1 of instance: adc0_da.
#011 : 011
Select mux mode: ALT3 mux port: QD_PHB of instance: flextimer1.
#100 : 100
Select mux mode: ALT4 mux port: LCD32 of instance: lcd_64f6b.
#101 : 101
Select mux mode: ALT5 mux port: TX_SYNC of instance: sai2.
#110 : 110
Select mux mode: ALT6 mux port: DATA[17] of instance: video_in0.
#111 : 111
Select mux mode: ALT7 mux port: QSCK_A of instance: quadspi1.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 9
address_offset : 0x24 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX DDR A7 Pad Control Register
address_offset : 0x240 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RESERVED : no description available
bits : 0 - 1 (2 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
RESERVED : no description available
bits : 10 - 13 (4 bit)
access : read-write
DDR_TRIM : no description available
bits : 14 - 15 (2 bit)
access : read-write
Enumeration:
#00 : 00
Minimum do->pad delay
#01 : 01
50 ps do->pad delay
#10 : 10
100 ps do->pad delay
#11 : 11
150 ps do->pad delay
End of enumeration elements list.
DDR_INPUT : no description available
bits : 16 - 16 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input type
#1 : 1
Differential input mode
End of enumeration elements list.
RESERVED : no description available
bits : 17 - 31 (15 bit)
access : read-write
Software MUX DDR A6 Pad Control Register
address_offset : 0x244 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RESERVED : no description available
bits : 0 - 1 (2 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
RESERVED : no description available
bits : 10 - 13 (4 bit)
access : read-write
DDR_TRIM : no description available
bits : 14 - 15 (2 bit)
access : read-write
Enumeration:
#00 : 00
Minimum do->pad delay
#01 : 01
50 ps do->pad delay
#10 : 10
100 ps do->pad delay
#11 : 11
150 ps do->pad delay
End of enumeration elements list.
DDR_INPUT : no description available
bits : 16 - 16 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input type
#1 : 1
Differential input mode
End of enumeration elements list.
RESERVED : no description available
bits : 17 - 31 (15 bit)
access : read-write
Software MUX DDR A5 Pad Control Register
address_offset : 0x248 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RESERVED : no description available
bits : 0 - 1 (2 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
RESERVED : no description available
bits : 10 - 13 (4 bit)
access : read-write
DDR_TRIM : no description available
bits : 14 - 15 (2 bit)
access : read-write
Enumeration:
#00 : 00
Minimum do->pad delay
#01 : 01
50 ps do->pad delay
#10 : 10
100 ps do->pad delay
#11 : 11
150 ps do->pad delay
End of enumeration elements list.
DDR_INPUT : no description available
bits : 16 - 16 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input type
#1 : 1
Differential input mode
End of enumeration elements list.
RESERVED : no description available
bits : 17 - 31 (15 bit)
access : read-write
Software MUX DDR A4 Pad Control Register
address_offset : 0x24C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RESERVED : no description available
bits : 0 - 1 (2 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
RESERVED : no description available
bits : 10 - 13 (4 bit)
access : read-write
DDR_TRIM : no description available
bits : 14 - 15 (2 bit)
access : read-write
Enumeration:
#00 : 00
Minimum do->pad delay
#01 : 01
50 ps do->pad delay
#10 : 10
100 ps do->pad delay
#11 : 11
150 ps do->pad delay
End of enumeration elements list.
DDR_INPUT : no description available
bits : 16 - 16 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input type
#1 : 1
Differential input mode
End of enumeration elements list.
RESERVED : no description available
bits : 17 - 31 (15 bit)
access : read-write
Software MUX DDR Pad A3 Control Register
address_offset : 0x250 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RESERVED : no description available
bits : 0 - 1 (2 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
RESERVED : no description available
bits : 10 - 13 (4 bit)
access : read-write
DDR_TRIM : no description available
bits : 14 - 15 (2 bit)
access : read-write
Enumeration:
#00 : 00
Minimum do->pad delay
#01 : 01
50 ps do->pad delay
#10 : 10
100 ps do->pad delay
#11 : 11
150 ps do->pad delay
End of enumeration elements list.
DDR_INPUT : no description available
bits : 16 - 16 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input type
#1 : 1
Differential input mode
End of enumeration elements list.
RESERVED : no description available
bits : 17 - 31 (15 bit)
access : read-write
Software MUX DDR A2 Pad Control Register
address_offset : 0x254 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RESERVED : no description available
bits : 0 - 1 (2 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
RESERVED : no description available
bits : 10 - 13 (4 bit)
access : read-write
DDR_TRIM : no description available
bits : 14 - 15 (2 bit)
access : read-write
Enumeration:
#00 : 00
Minimum do->pad delay
#01 : 01
50 ps do->pad delay
#10 : 10
100 ps do->pad delay
#11 : 11
150 ps do->pad delay
End of enumeration elements list.
DDR_INPUT : no description available
bits : 16 - 16 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input type
#1 : 1
Differential input mode
End of enumeration elements list.
RESERVED : no description available
bits : 17 - 31 (15 bit)
access : read-write
Software MUX DDR A1 Pad Control Register
address_offset : 0x258 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RESERVED : no description available
bits : 0 - 1 (2 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
RESERVED : no description available
bits : 10 - 13 (4 bit)
access : read-write
DDR_TRIM : no description available
bits : 14 - 15 (2 bit)
access : read-write
Enumeration:
#00 : 00
Minimum do->pad delay
#01 : 01
50 ps do->pad delay
#10 : 10
100 ps do->pad delay
#11 : 11
150 ps do->pad delay
End of enumeration elements list.
DDR_INPUT : no description available
bits : 16 - 16 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input type
#1 : 1
Differential input mode
End of enumeration elements list.
RESERVED : no description available
bits : 17 - 31 (15 bit)
access : read-write
Software MUX DDR A0 Pad Control Register
address_offset : 0x25C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RESERVED : no description available
bits : 0 - 1 (2 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
RESERVED : no description available
bits : 10 - 13 (4 bit)
access : read-write
DDR_TRIM : no description available
bits : 14 - 15 (2 bit)
access : read-write
Enumeration:
#00 : 00
Minimum do->pad delay
#01 : 01
50 ps do->pad delay
#10 : 10
100 ps do->pad delay
#11 : 11
150 ps do->pad delay
End of enumeration elements list.
DDR_INPUT : no description available
bits : 16 - 16 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input type
#1 : 1
Differential input mode
End of enumeration elements list.
RESERVED : no description available
bits : 17 - 31 (15 bit)
access : read-write
Software MUX DDR BA2 Pad Control Register
address_offset : 0x260 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RESERVED : no description available
bits : 0 - 1 (2 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
RESERVED : no description available
bits : 10 - 13 (4 bit)
access : read-write
DDR_TRIM : no description available
bits : 14 - 15 (2 bit)
access : read-write
Enumeration:
#00 : 00
Minimum do->pad delay
#01 : 01
50 ps do->pad delay
#10 : 10
100 ps do->pad delay
#11 : 11
150 ps do->pad delay
End of enumeration elements list.
DDR_INPUT : no description available
bits : 16 - 16 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input type
#1 : 1
Differential input mode
End of enumeration elements list.
RESERVED : no description available
bits : 17 - 31 (15 bit)
access : read-write
Software MUX DDR BA1 Pad Control Register
address_offset : 0x264 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RESERVED : no description available
bits : 0 - 1 (2 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
RESERVED : no description available
bits : 10 - 13 (4 bit)
access : read-write
DDR_TRIM : no description available
bits : 14 - 15 (2 bit)
access : read-write
Enumeration:
#00 : 00
Minimum do->pad delay
#01 : 01
50 ps do->pad delay
#10 : 10
100 ps do->pad delay
#11 : 11
150 ps do->pad delay
End of enumeration elements list.
DDR_INPUT : no description available
bits : 16 - 16 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input type
#1 : 1
Differential input mode
End of enumeration elements list.
RESERVED : no description available
bits : 17 - 31 (15 bit)
access : read-write
Software MUX DDR BA0 Pad Control Register
address_offset : 0x268 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RESERVED : no description available
bits : 0 - 1 (2 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
RESERVED : no description available
bits : 10 - 13 (4 bit)
access : read-write
DDR_TRIM : no description available
bits : 14 - 15 (2 bit)
access : read-write
Enumeration:
#00 : 00
Minimum do->pad delay
#01 : 01
50 ps do->pad delay
#10 : 10
100 ps do->pad delay
#11 : 11
150 ps do->pad delay
End of enumeration elements list.
DDR_INPUT : no description available
bits : 16 - 16 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input type
#1 : 1
Differential input mode
End of enumeration elements list.
RESERVED : no description available
bits : 17 - 31 (15 bit)
access : read-write
Software MUX DDR CAS Pad Control Register
address_offset : 0x26C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RESERVED : no description available
bits : 0 - 1 (2 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
RESERVED : no description available
bits : 10 - 13 (4 bit)
access : read-write
DDR_TRIM : no description available
bits : 14 - 15 (2 bit)
access : read-write
Enumeration:
#00 : 00
Minimum do->pad delay
#01 : 01
50 ps do->pad delay
#10 : 10
100 ps do->pad delay
#11 : 11
150 ps do->pad delay
End of enumeration elements list.
DDR_INPUT : no description available
bits : 16 - 16 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input type
#1 : 1
Differential input mode
End of enumeration elements list.
RESERVED : no description available
bits : 17 - 31 (15 bit)
access : read-write
Software MUX DDR CKE0 Pad Control Register
address_offset : 0x270 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RESERVED : no description available
bits : 0 - 1 (2 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
RESERVED : no description available
bits : 10 - 13 (4 bit)
access : read-write
DDR_TRIM : no description available
bits : 14 - 15 (2 bit)
access : read-write
Enumeration:
#00 : 00
Minimum do->pad delay
#01 : 01
50 ps do->pad delay
#10 : 10
100 ps do->pad delay
#11 : 11
150 ps do->pad delay
End of enumeration elements list.
DDR_INPUT : no description available
bits : 16 - 16 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input type
#1 : 1
Differential input mode
End of enumeration elements list.
RESERVED : no description available
bits : 17 - 31 (15 bit)
access : read-write
Software MUX DDR CLK0 Pad Control Register
address_offset : 0x274 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RESERVED : no description available
bits : 0 - 1 (2 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
RESERVED : no description available
bits : 10 - 13 (4 bit)
access : read-write
DDR_TRIM : no description available
bits : 14 - 15 (2 bit)
access : read-write
Enumeration:
#00 : 00
Minimum do->pad delay
#01 : 01
50 ps do->pad delay
#10 : 10
100 ps do->pad delay
#11 : 11
150 ps do->pad delay
End of enumeration elements list.
DDR_INPUT : no description available
bits : 16 - 16 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input type
#1 : 1
Differential input mode
End of enumeration elements list.
RESERVED : no description available
bits : 17 - 31 (15 bit)
access : read-write
Software MUX DDR CS B0 Pad Control Register
address_offset : 0x278 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RESERVED : no description available
bits : 0 - 1 (2 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
RESERVED : no description available
bits : 10 - 13 (4 bit)
access : read-write
DDR_TRIM : no description available
bits : 14 - 15 (2 bit)
access : read-write
Enumeration:
#00 : 00
Minimum do->pad delay
#01 : 01
50 ps do->pad delay
#10 : 10
100 ps do->pad delay
#11 : 11
150 ps do->pad delay
End of enumeration elements list.
DDR_INPUT : no description available
bits : 16 - 16 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input type
#1 : 1
Differential input mode
End of enumeration elements list.
RESERVED : no description available
bits : 17 - 31 (15 bit)
access : read-write
Software MUX DDR CS D15 Pad Control Register
address_offset : 0x27C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RESERVED : no description available
bits : 0 - 1 (2 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
RESERVED : no description available
bits : 10 - 13 (4 bit)
access : read-write
DDR_TRIM : no description available
bits : 14 - 15 (2 bit)
access : read-write
Enumeration:
#00 : 00
Minimum do->pad delay
#01 : 01
50 ps do->pad delay
#10 : 10
100 ps do->pad delay
#11 : 11
150 ps do->pad delay
End of enumeration elements list.
DDR_INPUT : no description available
bits : 16 - 16 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input type
#1 : 1
Differential input mode
End of enumeration elements list.
RESERVED : no description available
bits : 17 - 31 (15 bit)
access : read-write
Software MUX Pad Control Register 10
address_offset : 0x28 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 10
address_offset : 0x28 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[10] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: TRACED[4] of instance: platform.
#100 : 100
Select mux mode: ALT4 mux port: LCD33 of instance: lcd_64f6b.
#110 : 110
Select mux mode: ALT6 mux port: TX of instance: sci_flx3.
#111 : 111
Select mux mode: ALT7 mux port: TCON[1] of instance: tcon1.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX DDR CS D14 Pad Control Register
address_offset : 0x280 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RESERVED : no description available
bits : 0 - 1 (2 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
RESERVED : no description available
bits : 10 - 13 (4 bit)
access : read-write
DDR_TRIM : no description available
bits : 14 - 15 (2 bit)
access : read-write
Enumeration:
#00 : 00
Minimum do->pad delay
#01 : 01
50 ps do->pad delay
#10 : 10
100 ps do->pad delay
#11 : 11
150 ps do->pad delay
End of enumeration elements list.
DDR_INPUT : no description available
bits : 16 - 16 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input type
#1 : 1
Differential input mode
End of enumeration elements list.
RESERVED : no description available
bits : 17 - 31 (15 bit)
access : read-write
Software MUX DDR CS D13 Pad Control Register
address_offset : 0x284 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RESERVED : no description available
bits : 0 - 1 (2 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
RESERVED : no description available
bits : 10 - 13 (4 bit)
access : read-write
DDR_TRIM : no description available
bits : 14 - 15 (2 bit)
access : read-write
Enumeration:
#00 : 00
Minimum do->pad delay
#01 : 01
50 ps do->pad delay
#10 : 10
100 ps do->pad delay
#11 : 11
150 ps do->pad delay
End of enumeration elements list.
DDR_INPUT : no description available
bits : 16 - 16 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input type
#1 : 1
Differential input mode
End of enumeration elements list.
RESERVED : no description available
bits : 17 - 31 (15 bit)
access : read-write
Software MUX DDR CS D12 Pad Control Register
address_offset : 0x288 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RESERVED : no description available
bits : 0 - 1 (2 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
RESERVED : no description available
bits : 10 - 13 (4 bit)
access : read-write
DDR_TRIM : no description available
bits : 14 - 15 (2 bit)
access : read-write
Enumeration:
#00 : 00
Minimum do->pad delay
#01 : 01
50 ps do->pad delay
#10 : 10
100 ps do->pad delay
#11 : 11
150 ps do->pad delay
End of enumeration elements list.
DDR_INPUT : no description available
bits : 16 - 16 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input type
#1 : 1
Differential input mode
End of enumeration elements list.
RESERVED : no description available
bits : 17 - 31 (15 bit)
access : read-write
Software MUX DDR CS D11 Pad Control Register
address_offset : 0x28C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RESERVED : no description available
bits : 0 - 1 (2 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
RESERVED : no description available
bits : 10 - 13 (4 bit)
access : read-write
DDR_TRIM : no description available
bits : 14 - 15 (2 bit)
access : read-write
Enumeration:
#00 : 00
Minimum do->pad delay
#01 : 01
50 ps do->pad delay
#10 : 10
100 ps do->pad delay
#11 : 11
150 ps do->pad delay
End of enumeration elements list.
DDR_INPUT : no description available
bits : 16 - 16 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input type
#1 : 1
Differential input mode
End of enumeration elements list.
RESERVED : no description available
bits : 17 - 31 (15 bit)
access : read-write
Software MUX DDR CS D10 Pad Control Register
address_offset : 0x290 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RESERVED : no description available
bits : 0 - 1 (2 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
RESERVED : no description available
bits : 10 - 13 (4 bit)
access : read-write
DDR_TRIM : no description available
bits : 14 - 15 (2 bit)
access : read-write
Enumeration:
#00 : 00
Minimum do->pad delay
#01 : 01
50 ps do->pad delay
#10 : 10
100 ps do->pad delay
#11 : 11
150 ps do->pad delay
End of enumeration elements list.
DDR_INPUT : no description available
bits : 16 - 16 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input type
#1 : 1
Differential input mode
End of enumeration elements list.
RESERVED : no description available
bits : 17 - 31 (15 bit)
access : read-write
Software MUX DDR CS D9 Pad Control Register
address_offset : 0x294 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RESERVED : no description available
bits : 0 - 1 (2 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
RESERVED : no description available
bits : 10 - 13 (4 bit)
access : read-write
DDR_TRIM : no description available
bits : 14 - 15 (2 bit)
access : read-write
Enumeration:
#00 : 00
Minimum do->pad delay
#01 : 01
50 ps do->pad delay
#10 : 10
100 ps do->pad delay
#11 : 11
150 ps do->pad delay
End of enumeration elements list.
DDR_INPUT : no description available
bits : 16 - 16 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input type
#1 : 1
Differential input mode
End of enumeration elements list.
RESERVED : no description available
bits : 17 - 31 (15 bit)
access : read-write
Software MUX DDR CS D8 Pad Control Register
address_offset : 0x298 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RESERVED : no description available
bits : 0 - 1 (2 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
RESERVED : no description available
bits : 10 - 13 (4 bit)
access : read-write
DDR_TRIM : no description available
bits : 14 - 15 (2 bit)
access : read-write
Enumeration:
#00 : 00
Minimum do->pad delay
#01 : 01
50 ps do->pad delay
#10 : 10
100 ps do->pad delay
#11 : 11
150 ps do->pad delay
End of enumeration elements list.
DDR_INPUT : no description available
bits : 16 - 16 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input type
#1 : 1
Differential input mode
End of enumeration elements list.
RESERVED : no description available
bits : 17 - 31 (15 bit)
access : read-write
Software MUX DDR CS D7 Pad Control Register
address_offset : 0x29C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RESERVED : no description available
bits : 0 - 1 (2 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
RESERVED : no description available
bits : 10 - 13 (4 bit)
access : read-write
DDR_TRIM : no description available
bits : 14 - 15 (2 bit)
access : read-write
Enumeration:
#00 : 00
Minimum do->pad delay
#01 : 01
50 ps do->pad delay
#10 : 10
100 ps do->pad delay
#11 : 11
150 ps do->pad delay
End of enumeration elements list.
DDR_INPUT : no description available
bits : 16 - 16 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input type
#1 : 1
Differential input mode
End of enumeration elements list.
RESERVED : no description available
bits : 17 - 31 (15 bit)
access : read-write
Software MUX DDR CS D6 Pad Control Register
address_offset : 0x2A0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RESERVED : no description available
bits : 0 - 1 (2 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
RESERVED : no description available
bits : 10 - 13 (4 bit)
access : read-write
DDR_TRIM : no description available
bits : 14 - 15 (2 bit)
access : read-write
Enumeration:
#00 : 00
Minimum do->pad delay
#01 : 01
50 ps do->pad delay
#10 : 10
100 ps do->pad delay
#11 : 11
150 ps do->pad delay
End of enumeration elements list.
DDR_INPUT : no description available
bits : 16 - 16 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input type
#1 : 1
Differential input mode
End of enumeration elements list.
RESERVED : no description available
bits : 17 - 31 (15 bit)
access : read-write
Software MUX DDR CS D5 Pad Control Register
address_offset : 0x2A4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RESERVED : no description available
bits : 0 - 1 (2 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
RESERVED : no description available
bits : 10 - 13 (4 bit)
access : read-write
DDR_TRIM : no description available
bits : 14 - 15 (2 bit)
access : read-write
Enumeration:
#00 : 00
Minimum do->pad delay
#01 : 01
50 ps do->pad delay
#10 : 10
100 ps do->pad delay
#11 : 11
150 ps do->pad delay
End of enumeration elements list.
DDR_INPUT : no description available
bits : 16 - 16 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input type
#1 : 1
Differential input mode
End of enumeration elements list.
RESERVED : no description available
bits : 17 - 31 (15 bit)
access : read-write
Software MUX DDR CS D4 Pad Control Register
address_offset : 0x2A8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RESERVED : no description available
bits : 0 - 1 (2 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
RESERVED : no description available
bits : 10 - 13 (4 bit)
access : read-write
DDR_TRIM : no description available
bits : 14 - 15 (2 bit)
access : read-write
Enumeration:
#00 : 00
Minimum do->pad delay
#01 : 01
50 ps do->pad delay
#10 : 10
100 ps do->pad delay
#11 : 11
150 ps do->pad delay
End of enumeration elements list.
DDR_INPUT : no description available
bits : 16 - 16 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input type
#1 : 1
Differential input mode
End of enumeration elements list.
RESERVED : no description available
bits : 17 - 31 (15 bit)
access : read-write
Software MUX DDR CS D3 Pad Control Register
address_offset : 0x2AC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RESERVED : no description available
bits : 0 - 1 (2 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
RESERVED : no description available
bits : 10 - 13 (4 bit)
access : read-write
DDR_TRIM : no description available
bits : 14 - 15 (2 bit)
access : read-write
Enumeration:
#00 : 00
Minimum do->pad delay
#01 : 01
50 ps do->pad delay
#10 : 10
100 ps do->pad delay
#11 : 11
150 ps do->pad delay
End of enumeration elements list.
DDR_INPUT : no description available
bits : 16 - 16 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input type
#1 : 1
Differential input mode
End of enumeration elements list.
RESERVED : no description available
bits : 17 - 31 (15 bit)
access : read-write
Software MUX DDR CS D2 Pad Control Register
address_offset : 0x2B0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RESERVED : no description available
bits : 0 - 1 (2 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
RESERVED : no description available
bits : 10 - 13 (4 bit)
access : read-write
DDR_TRIM : no description available
bits : 14 - 15 (2 bit)
access : read-write
Enumeration:
#00 : 00
Minimum do->pad delay
#01 : 01
50 ps do->pad delay
#10 : 10
100 ps do->pad delay
#11 : 11
150 ps do->pad delay
End of enumeration elements list.
DDR_INPUT : no description available
bits : 16 - 16 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input type
#1 : 1
Differential input mode
End of enumeration elements list.
RESERVED : no description available
bits : 17 - 31 (15 bit)
access : read-write
Software MUX DDR CS D1 Pad Control Register
address_offset : 0x2B4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RESERVED : no description available
bits : 0 - 1 (2 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
RESERVED : no description available
bits : 10 - 13 (4 bit)
access : read-write
DDR_TRIM : no description available
bits : 14 - 15 (2 bit)
access : read-write
Enumeration:
#00 : 00
Minimum do->pad delay
#01 : 01
50 ps do->pad delay
#10 : 10
100 ps do->pad delay
#11 : 11
150 ps do->pad delay
End of enumeration elements list.
DDR_INPUT : no description available
bits : 16 - 16 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input type
#1 : 1
Differential input mode
End of enumeration elements list.
RESERVED : no description available
bits : 17 - 31 (15 bit)
access : read-write
Software MUX DDR CS D0 Pad Control Register
address_offset : 0x2B8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RESERVED : no description available
bits : 0 - 1 (2 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
RESERVED : no description available
bits : 10 - 13 (4 bit)
access : read-write
DDR_TRIM : no description available
bits : 14 - 15 (2 bit)
access : read-write
Enumeration:
#00 : 00
Minimum do->pad delay
#01 : 01
50 ps do->pad delay
#10 : 10
100 ps do->pad delay
#11 : 11
150 ps do->pad delay
End of enumeration elements list.
DDR_INPUT : no description available
bits : 16 - 16 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input type
#1 : 1
Differential input mode
End of enumeration elements list.
RESERVED : no description available
bits : 17 - 31 (15 bit)
access : read-write
Software MUX DDR DQM1 Pad Control Register
address_offset : 0x2BC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RESERVED : no description available
bits : 0 - 1 (2 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
RESERVED : no description available
bits : 10 - 13 (4 bit)
access : read-write
DDR_TRIM : no description available
bits : 14 - 15 (2 bit)
access : read-write
Enumeration:
#00 : 00
Minimum do->pad delay
#01 : 01
50 ps do->pad delay
#10 : 10
100 ps do->pad delay
#11 : 11
150 ps do->pad delay
End of enumeration elements list.
DDR_INPUT : no description available
bits : 16 - 16 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input type
#1 : 1
Differential input mode
End of enumeration elements list.
RESERVED : no description available
bits : 17 - 31 (15 bit)
access : read-write
Software MUX Pad Control Register 11
address_offset : 0x2C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[11] of instance: rgpioc. Also, RXCLK for MAC0 is enabled in this mux mode so ensure obe is disabled if this pin is used for MAC0-MII instead of GPIO.
#001 : 001
Select mux mode: ALT1 mux port: TRACED[5] of instance: platform.
#101 : 101
Select mux mode: ALT5 mux port: RX_BCLK of instance: sai2.
#110 : 110
Select mux mode: ALT6 mux port: RX of instance: sci_flx3.
#111 : 111
Select mux mode: ALT7 mux port: TCON[2] of instance: tcon1.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 11
address_offset : 0x2C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX DDR DQM0 Pad Control Register 0
address_offset : 0x2C0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RESERVED : no description available
bits : 0 - 1 (2 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
RESERVED : no description available
bits : 10 - 13 (4 bit)
access : read-write
DDR_TRIM : no description available
bits : 14 - 15 (2 bit)
access : read-write
Enumeration:
#00 : 00
Minimum do->pad delay
#01 : 01
50 ps do->pad delay
#10 : 10
100 ps do->pad delay
#11 : 11
150 ps do->pad delay
End of enumeration elements list.
DDR_INPUT : no description available
bits : 16 - 16 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input type
#1 : 1
Differential input mode
End of enumeration elements list.
RESERVED : no description available
bits : 17 - 31 (15 bit)
access : read-write
Software MUX DDR DQS1 Pad Control Register 1
address_offset : 0x2C4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RESERVED : no description available
bits : 0 - 1 (2 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
RESERVED : no description available
bits : 10 - 13 (4 bit)
access : read-write
DDR_TRIM : no description available
bits : 14 - 15 (2 bit)
access : read-write
Enumeration:
#00 : 00
Minimum do->pad delay
#01 : 01
50 ps do->pad delay
#10 : 10
100 ps do->pad delay
#11 : 11
150 ps do->pad delay
End of enumeration elements list.
DDR_INPUT : no description available
bits : 16 - 16 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input type
#1 : 1
Differential input mode
End of enumeration elements list.
RESERVED : no description available
bits : 17 - 31 (15 bit)
access : read-write
Software MUX DDR DQS0 Pad Control Register 0
address_offset : 0x2C8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RESERVED : no description available
bits : 0 - 1 (2 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
RESERVED : no description available
bits : 10 - 13 (4 bit)
access : read-write
DDR_TRIM : no description available
bits : 14 - 15 (2 bit)
access : read-write
Enumeration:
#00 : 00
Minimum do->pad delay
#01 : 01
50 ps do->pad delay
#10 : 10
100 ps do->pad delay
#11 : 11
150 ps do->pad delay
End of enumeration elements list.
DDR_INPUT : no description available
bits : 16 - 16 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input type
#1 : 1
Differential input mode
End of enumeration elements list.
RESERVED : no description available
bits : 17 - 31 (15 bit)
access : read-write
Software MUX DDR RAS Pad Control Register
address_offset : 0x2CC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RESERVED : no description available
bits : 0 - 1 (2 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
RESERVED : no description available
bits : 10 - 13 (4 bit)
access : read-write
DDR_TRIM : no description available
bits : 14 - 15 (2 bit)
access : read-write
Enumeration:
#00 : 00
Minimum do->pad delay
#01 : 01
50 ps do->pad delay
#10 : 10
100 ps do->pad delay
#11 : 11
150 ps do->pad delay
End of enumeration elements list.
DDR_INPUT : no description available
bits : 16 - 16 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input type
#1 : 1
Differential input mode
End of enumeration elements list.
RESERVED : no description available
bits : 17 - 31 (15 bit)
access : read-write
Software MUX DDR WE Pad Control Register
address_offset : 0x2D0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RESERVED : no description available
bits : 0 - 1 (2 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
RESERVED : no description available
bits : 10 - 13 (4 bit)
access : read-write
DDR_TRIM : no description available
bits : 14 - 15 (2 bit)
access : read-write
Enumeration:
#00 : 00
Minimum do->pad delay
#01 : 01
50 ps do->pad delay
#10 : 10
100 ps do->pad delay
#11 : 11
150 ps do->pad delay
End of enumeration elements list.
DDR_INPUT : no description available
bits : 16 - 16 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input type
#1 : 1
Differential input mode
End of enumeration elements list.
RESERVED : no description available
bits : 17 - 31 (15 bit)
access : read-write
Software MUX DDR ODT0 Pad Control Register
address_offset : 0x2D4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RESERVED : no description available
bits : 0 - 1 (2 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
RESERVED : no description available
bits : 10 - 13 (4 bit)
access : read-write
DDR_TRIM : no description available
bits : 14 - 15 (2 bit)
access : read-write
Enumeration:
#00 : 00
Minimum do->pad delay
#01 : 01
50 ps do->pad delay
#10 : 10
100 ps do->pad delay
#11 : 11
150 ps do->pad delay
End of enumeration elements list.
DDR_INPUT : no description available
bits : 16 - 16 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input type
#1 : 1
Differential input mode
End of enumeration elements list.
RESERVED : no description available
bits : 17 - 31 (15 bit)
access : read-write
Software MUX DDR ODT1 Pad Control Register
address_offset : 0x2D8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RESERVED : no description available
bits : 0 - 1 (2 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
RESERVED : no description available
bits : 10 - 13 (4 bit)
access : read-write
DDR_TRIM : no description available
bits : 14 - 15 (2 bit)
access : read-write
Enumeration:
#00 : 00
Minimum do->pad delay
#01 : 01
50 ps do->pad delay
#10 : 10
100 ps do->pad delay
#11 : 11
150 ps do->pad delay
End of enumeration elements list.
DDR_INPUT : no description available
bits : 16 - 16 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input type
#1 : 1
Differential input mode
End of enumeration elements list.
RESERVED : no description available
bits : 17 - 31 (15 bit)
access : read-write
Software MUX Dummy DDRBYTE1 Pad Control Register
address_offset : 0x2DC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RESERVED : no description available
bits : 0 - 1 (2 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
RESERVED : no description available
bits : 10 - 13 (4 bit)
access : read-write
DDR_TRIM : no description available
bits : 14 - 15 (2 bit)
access : read-write
Enumeration:
#00 : 00
Minimum do->pad delay
#01 : 01
50 ps do->pad delay
#10 : 10
100 ps do->pad delay
#11 : 11
150 ps do->pad delay
End of enumeration elements list.
DDR_INPUT : no description available
bits : 16 - 16 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input type
#1 : 1
Differential input mode
End of enumeration elements list.
RESERVED : no description available
bits : 17 - 31 (15 bit)
access : read-write
Software MUX Dummy DDRBYTE2 Pad Control Register
address_offset : 0x2E0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RESERVED : no description available
bits : 0 - 1 (2 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
RESERVED : no description available
bits : 10 - 13 (4 bit)
access : read-write
DDR_TRIM : no description available
bits : 14 - 15 (2 bit)
access : read-write
Enumeration:
#00 : 00
Minimum do->pad delay
#01 : 01
50 ps do->pad delay
#10 : 10
100 ps do->pad delay
#11 : 11
150 ps do->pad delay
End of enumeration elements list.
DDR_INPUT : no description available
bits : 16 - 16 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input type
#1 : 1
Differential input mode
End of enumeration elements list.
RESERVED : no description available
bits : 17 - 31 (15 bit)
access : read-write
CCM Audio External Clock Input Select Register
address_offset : 0x2EC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DAISY : no description available
bits : 0 - 1 (2 bit)
access : read-write
Enumeration:
#00 : 00
Selecting Pad: PTA10 for Mode: ALT2.
#01 : 01
Selecting Pad: PTA12 for Mode: ALT2.
#10 : 10
Selecting Pad: PTB18 for Mode: ALT2.
End of enumeration elements list.
RESERVED : no description available
bits : 2 - 31 (30 bit)
access : read-write
CCM Ethernet External Clock Input Select Register
address_offset : 0x2F0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DAISY : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Selecting Pad: PTA6 for Mode: ALT2.
#1 : 1
Selecting Pad: PTA9 for Mode: ALT3.
End of enumeration elements list.
RESERVED : no description available
bits : 1 - 31 (31 bit)
access : read-write
CCM Ethernet TS Clock Input Select Register
address_offset : 0x2F4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DAISY : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Selecting Pad: PTA10 for Mode: ALT6.
#1 : 1
Selecting Pad: PTB10 for Mode: ALT7.
End of enumeration elements list.
RESERVED : no description available
bits : 1 - 31 (31 bit)
access : read-write
DSPI1 SCK Input Select Register
address_offset : 0x2F8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DAISY : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Selecting Pad: PTC8 for Mode: ALT3.
#1 : 1
Selecting Pad: PTD8 for Mode: ALT3.
End of enumeration elements list.
RESERVED : no description available
bits : 1 - 31 (31 bit)
access : read-write
DSPI1 SIN Input Select Register
address_offset : 0x2FC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DAISY : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Selecting Pad: PTC6 for Mode: ALT3.
#1 : 1
Selecting Pad: PTD6 for Mode: ALT3.
End of enumeration elements list.
RESERVED : no description available
bits : 1 - 31 (31 bit)
access : read-write
Software MUX Pad Control Register 12
address_offset : 0x30 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[12] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: TRACED[6] of instance: platform.
#101 : 101
Select mux mode: ALT5 mux port: RX_DATA of instance: sai2.
#110 : 110
Select mux mode: ALT6 mux port: SCL of instance: i2c2.
#111 : 111
Select mux mode: ALT7 mux port: TCON[0] of instance: tcon1.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 12
address_offset : 0x30 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
DSPI1 SS Input Select Register
address_offset : 0x300 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DAISY : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Selecting Pad: PTC5 for Mode: ALT3.
#1 : 1
Selecting Pad: PTD5 for Mode: ALT3.
End of enumeration elements list.
RESERVED : no description available
bits : 1 - 31 (31 bit)
access : read-write
Ethernet MAC0 TIMER0 Input Select Register
address_offset : 0x304 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DAISY : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Selecting Pad: PTB11 for Mode: ALT7.
#1 : 1
Selecting Pad: PTD23 for Mode: ALT4.
End of enumeration elements list.
RESERVED : no description available
bits : 1 - 31 (31 bit)
access : read-write
Ethernet MAC0 TIMER1 Input Select Register
address_offset : 0x308 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DAISY : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Selecting Pad: PTB12 for Mode: ALT7.
#1 : 1
Selecting Pad: PTD22 for Mode: ALT4.
End of enumeration elements list.
RESERVED : no description available
bits : 1 - 31 (31 bit)
access : read-write
ESAI FST Input Select Register
address_offset : 0x30C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DAISY : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Selecting Pad: PTC1 for Mode: ALT4.
#1 : 1
Selecting Pad: PTC10 for Mode: ALT3.
End of enumeration elements list.
RESERVED : no description available
bits : 1 - 31 (31 bit)
access : read-write
ESAI SCKT Input Select Register
address_offset : 0x310 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DAISY : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Selecting Pad: PTC0 for Mode: ALT4.
#1 : 1
Selecting Pad: PTC9 for Mode: ALT3.
End of enumeration elements list.
RESERVED : no description available
bits : 1 - 31 (31 bit)
access : read-write
ESAI SDO0 Input Select Register
address_offset : 0x314 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DAISY : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Selecting Pad: PTC2 for Mode: ALT4.
#1 : 1
Selecting Pad: PTC11 for Mode: ALT3.
End of enumeration elements list.
RESERVED : no description available
bits : 1 - 31 (31 bit)
access : read-write
ESAI SDO1 Input Select Register
address_offset : 0x318 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DAISY : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Selecting Pad: PTC3 for Mode: ALT4.
#1 : 1
Selecting Pad: PTC12 for Mode: ALT3.
End of enumeration elements list.
RESERVED : no description available
bits : 1 - 31 (31 bit)
access : read-write
ESAI SDO2 Input Select Register
address_offset : 0x31C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DAISY : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Selecting Pad: PTC4 for Mode: ALT4.
#1 : 1
Selecting Pad: PTC13 for Mode: ALT3.
End of enumeration elements list.
RESERVED : no description available
bits : 1 - 31 (31 bit)
access : read-write
ESAI SDO3 Input Select Register
address_offset : 0x320 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DAISY : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Selecting Pad: PTC5 for Mode: ALT4.
#1 : 1
Selecting Pad: PTC14 for Mode: ALT3.
End of enumeration elements list.
RESERVED : no description available
bits : 1 - 31 (31 bit)
access : read-write
ESAI SDO4 Input Select Register
address_offset : 0x324 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DAISY : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Selecting Pad: PTC7 for Mode: ALT4.
#1 : 1
Selecting Pad: PTC16 for Mode: ALT3.
End of enumeration elements list.
RESERVED : no description available
bits : 1 - 31 (31 bit)
access : read-write
ESAI SDO5 Input Select Register
address_offset : 0x328 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DAISY : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Selecting Pad: PTC6 for Mode: ALT4.
#1 : 1
Selecting Pad: PTC15 for Mode: ALT3.
End of enumeration elements list.
RESERVED : no description available
bits : 1 - 31 (31 bit)
access : read-write
FlexTimer1 CH0 Input Select Register
address_offset : 0x32C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DAISY : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Selecting Pad: PTB8 for Mode: ALT1.
#1 : 1
Selecting Pad: PTC0 for Mode: ALT2.
End of enumeration elements list.
RESERVED : no description available
bits : 1 - 31 (31 bit)
access : read-write
FlexTimer1 CH1 Input Select Register
address_offset : 0x330 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DAISY : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Selecting Pad: PTB9 for Mode: ALT1.
#1 : 1
Selecting Pad: PTC1 for Mode: ALT2.
End of enumeration elements list.
RESERVED : no description available
bits : 1 - 31 (31 bit)
access : read-write
FlexTimer1 PHA Input Select Register
address_offset : 0x334 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DAISY : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Selecting Pad: PTA18 for Mode: ALT3.
#1 : 1
Selecting Pad: PTB8 for Mode: ALT3.
End of enumeration elements list.
RESERVED : no description available
bits : 1 - 31 (31 bit)
access : read-write
FlexTimer1 PHB Input Select Register
address_offset : 0x338 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DAISY : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Selecting Pad: PTA19 for Mode: ALT3.
#1 : 1
Selecting Pad: PTB9 for Mode: ALT3.
End of enumeration elements list.
RESERVED : no description available
bits : 1 - 31 (31 bit)
access : read-write
I2C0 SCL Input Select Register
address_offset : 0x33C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DAISY : no description available
bits : 0 - 1 (2 bit)
access : read-write
Enumeration:
#00 : 00
Selecting Pad: PTA12 for Mode: ALT7.
#01 : 01
Selecting Pad: PTB14 for Mode: ALT2.
#10 : 10
Selecting Pad: PTD19 for Mode: ALT4.
#11 : 11
Selecting Pad: PTE19 for Mode: ALT5.
End of enumeration elements list.
RESERVED : no description available
bits : 2 - 31 (30 bit)
access : read-write
Software MUX Pad Control Register 13
address_offset : 0x34 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 13
address_offset : 0x34 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[13] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: TRACED[7] of instance: platform.
#101 : 101
Select mux mode: ALT5 mux port: RX_SYNC of instance: sai2.
#110 : 110
Select mux mode: ALT6 mux port: SDA of instance: i2c2.
#111 : 111
Select mux mode: ALT7 mux port: TCON[3] of instance: tcon1.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
I2C0 SDA Input Select Register
address_offset : 0x340 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DAISY : no description available
bits : 0 - 1 (2 bit)
access : read-write
Enumeration:
#00 : 00
Selecting Pad: PTA16 for Mode: ALT7.
#01 : 01
Selecting Pad: PTB15 for Mode: ALT2.
#10 : 10
Selecting Pad: PTD18 for Mode: ALT4.
#11 : 11
Selecting Pad: PTE20 for Mode: ALT5.
End of enumeration elements list.
RESERVED : no description available
bits : 2 - 31 (30 bit)
access : read-write
I2C1 SCL Input Select Register
address_offset : 0x344 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DAISY : no description available
bits : 0 - 1 (2 bit)
access : read-write
Enumeration:
#00 : 00
Selecting Pad: PTA17 for Mode: ALT7.
#01 : 01
Selecting Pad: PTB16 for Mode: ALT2.
#10 : 10
Selecting Pad: PTD17 for Mode: ALT4.
#11 : 11
Selecting Pad: PTE27 for Mode: ALT5.
End of enumeration elements list.
RESERVED : no description available
bits : 2 - 31 (30 bit)
access : read-write
I2C1 SDA Input Select Register
address_offset : 0x348 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DAISY : no description available
bits : 0 - 1 (2 bit)
access : read-write
Enumeration:
#00 : 00
Selecting Pad: PTA18 for Mode: ALT7.
#01 : 01
Selecting Pad: PTB17 for Mode: ALT2.
#10 : 10
Selecting Pad: PTD16 for Mode: ALT4.
#11 : 11
Selecting Pad: PTE28 for Mode: ALT5.
End of enumeration elements list.
RESERVED : no description available
bits : 2 - 31 (30 bit)
access : read-write
I2C2 SCL Input Select Register
address_offset : 0x34C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DAISY : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Selecting Pad: PTA22 for Mode: ALT6.
#1 : 1
Selecting Pad: PTD28 for Mode: ALT3.
End of enumeration elements list.
RESERVED : no description available
bits : 1 - 31 (31 bit)
access : read-write
I2C2 SDA Input Select Register
address_offset : 0x350 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DAISY : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Selecting Pad: PTA23 for Mode: ALT6.
#1 : 1
Selecting Pad: PTD27 for Mode: ALT3.
End of enumeration elements list.
RESERVED : no description available
bits : 1 - 31 (31 bit)
access : read-write
MediaLB Clock Input Select Register
address_offset : 0x354 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DAISY : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Selecting Pad: PTA8 for Mode: ALT7.
#1 : 1
Selecting Pad: PTC9 for Mode: ALT6.
End of enumeration elements list.
RESERVED : no description available
bits : 1 - 31 (31 bit)
access : read-write
MediaLB Data Input Select Register
address_offset : 0x358 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DAISY : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Selecting Pad: PTA11 for Mode: ALT7.
#1 : 1
Selecting Pad: PTC11 for Mode: ALT6.
End of enumeration elements list.
RESERVED : no description available
bits : 1 - 31 (31 bit)
access : read-write
MediaLB Signal Input Select Register
address_offset : 0x35C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DAISY : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Selecting Pad: PTA10 for Mode: ALT7.
#1 : 1
Selecting Pad: PTC10 for Mode: ALT6.
End of enumeration elements list.
RESERVED : no description available
bits : 1 - 31 (31 bit)
access : read-write
SAI1 TXSYNC Input Select Register
address_offset : 0x360 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DAISY : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Selecting Pad: PTD9 for Mode: ALT6.
#1 : 1
Selecting Pad: PTC31 for Mode: ALT1.
End of enumeration elements list.
RESERVED : no description available
bits : 1 - 31 (31 bit)
access : read-write
SAI2 RXBCLK Input Select Register
address_offset : 0x364 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DAISY : no description available
bits : 0 - 1 (2 bit)
access : read-write
Enumeration:
#00 : 00
Selecting Pad: PTA21 for Mode: ALT5.
#01 : 01
Selecting Pad: PTB0 for Mode: ALT5.
#10 : 10
Selecting Pad: PTC13 for Mode: ALT5.
End of enumeration elements list.
RESERVED : no description available
bits : 2 - 31 (30 bit)
access : read-write
SAI2 RXDATA0 Input Select Register
address_offset : 0x368 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DAISY : no description available
bits : 0 - 1 (2 bit)
access : read-write
Enumeration:
#00 : 00
Selecting Pad: PTA22 for Mode: ALT5.
#01 : 01
Selecting Pad: PTB1 for Mode: ALT5.
#10 : 10
Selecting Pad: PTC14 for Mode: ALT5.
End of enumeration elements list.
RESERVED : no description available
bits : 2 - 31 (30 bit)
access : read-write
SAI2 RXSYNC Input Select Register
address_offset : 0x36C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DAISY : no description available
bits : 0 - 1 (2 bit)
access : read-write
Enumeration:
#00 : 00
Selecting Pad: PTA23 for Mode: ALT5.
#01 : 01
Selecting Pad: PTB2 for Mode: ALT5.
#10 : 10
Selecting Pad: PTC16 for Mode: ALT5.
End of enumeration elements list.
RESERVED : no description available
bits : 2 - 31 (30 bit)
access : read-write
SAI2 TXBLCK Input Select Register
address_offset : 0x370 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DAISY : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Selecting Pad: PTA16 for Mode: ALT5.
#1 : 1
Selecting Pad: PTC12 for Mode: ALT5.
End of enumeration elements list.
RESERVED : no description available
bits : 1 - 31 (31 bit)
access : read-write
SAI2 TXSYNC Input Select Register
address_offset : 0x374 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DAISY : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Selecting Pad: PTA19 for Mode: ALT5.
#1 : 1
Selecting Pad: PTC17 for Mode: ALT5.
End of enumeration elements list.
RESERVED : no description available
bits : 1 - 31 (31 bit)
access : read-write
UART FLX1 CTS Input Select Register
address_offset : 0x378 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DAISY : no description available
bits : 0 - 1 (2 bit)
access : read-write
Enumeration:
#00 : 00
Selecting Pad: PTB7 for Mode: ALT2.
#01 : 01
Selecting Pad: PTC5 for Mode: ALT2.
#10 : 10
Selecting Pad: PTB26 for Mode: ALT2.
End of enumeration elements list.
RESERVED : no description available
bits : 2 - 31 (30 bit)
access : read-write
UART FLX1 RX Input Select Register
address_offset : 0x37C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DAISY : no description available
bits : 0 - 1 (2 bit)
access : read-write
Enumeration:
#00 : 00
Selecting Pad: PTB5 for Mode: ALT2.
#01 : 01
Selecting Pad: PTC3 for Mode: ALT2.
#10 : 10
Selecting Pad: PTB24 for Mode: ALT2.
End of enumeration elements list.
RESERVED : no description available
bits : 2 - 31 (30 bit)
access : read-write
Software MUX Pad Control Register 14
address_offset : 0x38 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 14
address_offset : 0x38 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[14] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: TRACED[8] of instance: platform.
#010 : 010
Select mux mode: ALT2 mux port: VBUS_EN of instance: usb.
#101 : 101
Select mux mode: ALT5 mux port: CLK of instance: esdhc1.
#110 : 110
Select mux mode: ALT6 mux port: TCON[4] of instance: tcon1.
#111 : 111
Select mux mode: ALT7 mux port: PAD_CTRL of instance: ddr_test_logic.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
UART FLX1 TX Input Select Register
address_offset : 0x380 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DAISY : no description available
bits : 0 - 1 (2 bit)
access : read-write
Enumeration:
#00 : 00
Selecting Pad: PTB4 for Mode: ALT2.
#01 : 01
Selecting Pad: PTC2 for Mode: ALT2.
#10 : 10
Selecting Pad: PTB23 for Mode: ALT2.
End of enumeration elements list.
RESERVED : no description available
bits : 2 - 31 (30 bit)
access : read-write
UART FLX2 CTS Input Select Register
address_offset : 0x384 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DAISY : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Selecting Pad: PTD20 for Mode: ALT6.
#1 : 1
Selecting Pad: PTD3 for Mode: ALT2.
End of enumeration elements list.
RESERVED : no description available
bits : 1 - 31 (31 bit)
access : read-write
UART FLX2 RX Input Select Register
address_offset : 0x388 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DAISY : no description available
bits : 0 - 1 (2 bit)
access : read-write
Enumeration:
#00 : 00
Selecting Pad: PTB7 for Mode: ALT7.
#01 : 01
Selecting Pad: PTD22 for Mode: ALT6.
#10 : 10
Selecting Pad: PTD1 for Mode: ALT2.
End of enumeration elements list.
RESERVED : no description available
bits : 2 - 31 (30 bit)
access : read-write
UART FLX2 TX Input Select Register
address_offset : 0x38C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DAISY : no description available
bits : 0 - 1 (2 bit)
access : read-write
Enumeration:
#00 : 00
Selecting Pad: PTB6 for Mode: ALT7.
#01 : 01
Selecting Pad: PTD23 for Mode: ALT6.
#10 : 10
Selecting Pad: PTD0 for Mode: ALT2.
End of enumeration elements list.
RESERVED : no description available
bits : 2 - 31 (30 bit)
access : read-write
UART FLX3 RX Input Select Register
address_offset : 0x390 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DAISY : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Selecting Pad: PTA21 for Mode: ALT6.
#1 : 1
Selecting Pad: PTA31 for Mode: ALT7.
End of enumeration elements list.
RESERVED : no description available
bits : 1 - 31 (31 bit)
access : read-write
UART FLX3 TX Input Select Register
address_offset : 0x394 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DAISY : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Selecting Pad: PTA20 for Mode: ALT6.
#1 : 1
Selecting Pad: PTA30 for Mode: ALT7.
End of enumeration elements list.
RESERVED : no description available
bits : 1 - 31 (31 bit)
access : read-write
BOOTCFG18 Input Select Register
address_offset : 0x398 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DAISY : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Selecting Pad: PTC0 for Mode: ALT7.
#1 : 1
Selecting Pad: PTB23 for Mode: ALT3.
End of enumeration elements list.
RESERVED : no description available
bits : 1 - 31 (31 bit)
access : read-write
BOOTCFG19 Input Select Register
address_offset : 0x39C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DAISY : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Selecting Pad: PTC1 for Mode: ALT7.
#1 : 1
Selecting Pad: PTB24 for Mode: ALT3.
End of enumeration elements list.
RESERVED : no description available
bits : 1 - 31 (31 bit)
access : read-write
BOOTCFG20 Input Select Register
address_offset : 0x3A0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DAISY : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Selecting Pad: PTC2 for Mode: ALT7.
#1 : 1
Selecting Pad: PTB25 for Mode: ALT3.
End of enumeration elements list.
RESERVED : no description available
bits : 1 - 31 (31 bit)
access : read-write
Video Decoder Input Select Register
address_offset : 0x3A4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DAISY : no description available
bits : 0 - 1 (2 bit)
access : read-write
Enumeration:
#00 : 00
Selecting Pad: PTB5 for Mode: ALT5.
#01 : 01
Selecting Pad: PTB8 for Mode: ALT5.
#10 : 10
Selecting Pad: PTB10 for Mode: ALT5.
End of enumeration elements list.
RESERVED : no description available
bits : 2 - 31 (30 bit)
access : read-write
Video IN0 Input Select Register
address_offset : 0x3A8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DAISY : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Selecting Pad: PTB4 for Mode: ALT5.
#1 : 1
Selecting Pad: PTB22 for Mode: ALT5.
End of enumeration elements list.
RESERVED : no description available
bits : 1 - 31 (31 bit)
access : read-write
Video PIXCLK Input Select Register
address_offset : 0x3AC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DAISY : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Selecting Pad: PTB15 for Mode: ALT7.
#1 : 1
Selecting Pad: PTA7 for Mode: ALT1.
End of enumeration elements list.
RESERVED : no description available
bits : 1 - 31 (31 bit)
access : read-write
Software MUX Pad Control Register 15
address_offset : 0x3C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[15] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: TRACED[9] of instance: platform.
#010 : 010
Select mux mode: ALT2 mux port: VBUS_OC of instance: usb.
#101 : 101
Select mux mode: ALT5 mux port: CMD of instance: esdhc1.
#110 : 110
Select mux mode: ALT6 mux port: TCON[5] of instance: tcon1.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 15
address_offset : 0x3C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 1
address_offset : 0x4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 1
address_offset : 0x4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[1] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: TCLK of instance: debug.
#100 : 100
Select mux mode: ALT4 mux port: DATA_OUT[18] of instance: tcon0.
#111 : 111
Select mux mode: ALT7 mux port: MLBCLK of instance: mlb_top.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 16
address_offset : 0x40 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 16
address_offset : 0x40 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[16] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: TRACED[10] of instance: platform.
#010 : 010
Select mux mode: ALT2 mux port: TX_BCLK of instance: sai3.
#101 : 101
Select mux mode: ALT5 mux port: DAT0 of instance: esdhc1.
#110 : 110
Select mux mode: ALT6 mux port: TCON[6] of instance: tcon1.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 17
address_offset : 0x44 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 17
address_offset : 0x44 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[17] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: TRACED[11] of instance: platform.
#010 : 010
Select mux mode: ALT2 mux port: RX_BCLK of instance: sai3.
#101 : 101
Select mux mode: ALT5 mux port: DAT1 of instance: esdhc1.
#110 : 110
Select mux mode: ALT6 mux port: TCON[7] of instance: tcon1.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 18
address_offset : 0x48 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 18
address_offset : 0x48 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[18] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: TRACED[12] of instance: platform.
#010 : 010
Select mux mode: ALT2 mux port: RX_DATA of instance: sai3.
#011 : 011
Select mux mode: ALT3 mux port: MAC1_TMR0 of instance: enet_swiahb.
#100 : 100
Select mux mode: ALT4 mux port: TX of instance: sci_flx4.
#101 : 101
Select mux mode: ALT5 mux port: DAT2 of instance: esdhc1.
#110 : 110
Select mux mode: ALT6 mux port: TCON[8] of instance: tcon1.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 19
address_offset : 0x4C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[19] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: TRACED[13] of instance: platform.
#010 : 010
Select mux mode: ALT2 mux port: TX_DATA of instance: sai3.
#011 : 011
Select mux mode: ALT3 mux port: MAC1_TMR1 of instance: enet_swiahb.
#100 : 100
Select mux mode: ALT4 mux port: RX of instance: sci_flx4.
#101 : 101
Select mux mode: ALT5 mux port: DAT3 of instance: esdhc1.
#110 : 110
Select mux mode: ALT6 mux port: TCON[9] of instance: tcon1.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 19
address_offset : 0x4C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 20
address_offset : 0x50 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[20] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: TRACED[14] of instance: platform.
#010 : 010
Select mux mode: ALT2 mux port: RX_SYNC of instance: sai3.
#011 : 011
Select mux mode: ALT3 mux port: MAC1_TMR2 of instance: enet_swiahb.
#100 : 100
Select mux mode: ALT4 mux port: RTS of instance: sci_flx4.
#101 : 101
Select mux mode: ALT5 mux port: SCL of instance: i2c3.
#111 : 111
Select mux mode: ALT7 mux port: TX of instance: sci_flx3.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 20
address_offset : 0x50 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 21
address_offset : 0x54 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 21
address_offset : 0x54 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[21] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: TRACED[15] of instance: platform.
#010 : 010
Select mux mode: ALT2 mux port: TX_SYNC of instance: sai3.
#100 : 100
Select mux mode: ALT4 mux port: CTS of instance: sci_flx4.
#101 : 101
Select mux mode: ALT5 mux port: SDA of instance: i2c3.
#111 : 111
Select mux mode: ALT7 mux port: RX of instance: sci_flx3.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 22
address_offset : 0x58 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 22
address_offset : 0x58 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[22] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: CH[0] of instance: flextimer0.
#010 : 010
Select mux mode: ALT2 mux port: ADC0SE2 of instance: adc0_da.
#011 : 011
Select mux mode: ALT3 mux port: TRACECTL of instance: platform.
#100 : 100
Select mux mode: ALT4 mux port: LCD34 of instance: lcd_64f6b.
#101 : 101
Select mux mode: ALT5 mux port: RX_BCLK of instance: sai2.
#110 : 110
Select mux mode: ALT6 mux port: DATA[18] of instance: video_in0.
#111 : 111
Select mux mode: ALT7 mux port: QPCS0_A of instance: quadspi1.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 23
address_offset : 0x5C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 23
address_offset : 0x5C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[23] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: CH[1] of instance: flextimer0.
#010 : 010
Select mux mode: ALT2 mux port: ADC0SE3 of instance: adc0_da.
#011 : 011
Select mux mode: ALT3 mux port: RCON30 of instance: src.
#100 : 100
Select mux mode: ALT4 mux port: LCD35 of instance: lcd_64f6b.
#101 : 101
Select mux mode: ALT5 mux port: RX_DATA of instance: sai2.
#110 : 110
Select mux mode: ALT6 mux port: DATA[19] of instance: video_in0.
#111 : 111
Select mux mode: ALT7 mux port: QSPI_IO3_A of instance: quadspi1.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 24
address_offset : 0x60 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 24
address_offset : 0x60 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[24] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: CH[2] of instance: flextimer0.
#010 : 010
Select mux mode: ALT2 mux port: ADC1SE2 of instance: adc1_da.
#011 : 011
Select mux mode: ALT3 mux port: RCON31 of instance: src.
#100 : 100
Select mux mode: ALT4 mux port: LCD36 of instance: lcd_64f6b.
#101 : 101
Select mux mode: ALT5 mux port: RX_SYNC of instance: sai2.
#110 : 110
Select mux mode: ALT6 mux port: DATA[20] of instance: video_in0.
#111 : 111
Select mux mode: ALT7 mux port: QSPI_IO2_A of instance: quadspi1.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 25
address_offset : 0x64 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 25
address_offset : 0x64 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[25] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: CH[3] of instance: flextimer0.
#010 : 010
Select mux mode: ALT2 mux port: ADC1SE3 of instance: adc1_da.
#011 : 011
Select mux mode: ALT3 mux port: EXTRIG of instance: pdb.
#100 : 100
Select mux mode: ALT4 mux port: LCD37 of instance: lcd_64f6b.
#110 : 110
Select mux mode: ALT6 mux port: DATA[21] of instance: video_in0.
#111 : 111
Select mux mode: ALT7 mux port: QSPI_IO1_A of instance: quadspi1.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 26
address_offset : 0x68 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 26
address_offset : 0x68 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[26] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: CH[4] of instance: flextimer0.
#010 : 010
Select mux mode: ALT2 mux port: TX of instance: sci_flx1.
#011 : 011
Select mux mode: ALT3 mux port: ADC0SE4 of instance: adc0_da.
#100 : 100
Select mux mode: ALT4 mux port: LCD38 of instance: lcd_64f6b.
#101 : 101
Select mux mode: ALT5 mux port: VIU_FID of instance: video_in0.
#110 : 110
Select mux mode: ALT6 mux port: DATA[22] of instance: video_in0.
#111 : 111
Select mux mode: ALT7 mux port: QSPI_IO0_A of instance: quadspi1.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 27
address_offset : 0x6C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 27
address_offset : 0x6C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[27] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: CH[5] of instance: flextimer0.
#010 : 010
Select mux mode: ALT2 mux port: RX of instance: sci_flx1.
#011 : 011
Select mux mode: ALT3 mux port: ADC1SE4 of instance: adc1_da.
#100 : 100
Select mux mode: ALT4 mux port: LCD39 of instance: lcd_64f6b.
#101 : 101
Select mux mode: ALT5 mux port: VIU_DE of instance: video_in0.
#110 : 110
Reserved
#111 : 111
Select mux mode: ALT7 mux port: DQS_A of instance: quadspi1.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 28
address_offset : 0x70 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[28] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: CH[6] of instance: flextimer0.
#010 : 010
Select mux mode: ALT2 mux port: RTS of instance: sci_flx1.
#011 : 011
Select mux mode: ALT3 mux port: QPCS1_A of instance: quadspi0.
#100 : 100
Select mux mode: ALT4 mux port: LCD40 of instance: lcd_64f6b.
#101 : 101
Select mux mode: ALT5 mux port: FB_CLKOUT of instance: lpcg0.
#110 : 110
Select mux mode: ALT6 mux port: HSYNC of instance: video_in0.
#111 : 111
Select mux mode: ALT7 mux port: TX of instance: sci_flx2.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 28
address_offset : 0x70 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 29
address_offset : 0x74 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 29
address_offset : 0x74 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[29] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: CH[7] of instance: flextimer0.
#010 : 010
Select mux mode: ALT2 mux port: CTS of instance: sci_flx1.
#011 : 011
Select mux mode: ALT3 mux port: QPCS1_B of instance: quadspi0.
#100 : 100
Select mux mode: ALT4 mux port: LCD41 of instance: lcd_64f6b.
#110 : 110
Select mux mode: ALT6 mux port: VSYNC of instance: video_in0.
#111 : 111
Select mux mode: ALT7 mux port: RX of instance: sci_flx2.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 30
address_offset : 0x78 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[30] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: CH[0] of instance: flextimer1.
#011 : 011
Select mux mode: ALT3 mux port: QD_PHA of instance: flextimer1.
#101 : 101
Select mux mode: ALT5 mux port: VIU_DE of instance: video_in0.
#111 : 111
Select mux mode: ALT7 mux port: DATA_OUT[24] of instance: tcon1.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 30
address_offset : 0x78 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 31
address_offset : 0x7C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 31
address_offset : 0x7C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[31] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: CH[1] of instance: flextimer1.
#011 : 011
Select mux mode: ALT3 mux port: QD_PHB of instance: flextimer1.
#111 : 111
Select mux mode: ALT7 mux port: DATA_OUT[25] of instance: tcon1.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 2
address_offset : 0x8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 2
address_offset : 0x8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[2] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: TDI of instance: debug.
#010 : 010
Select mux mode: ALT2 mux port: RMII_CLKOUT of instance: ccm.
#011 : 011
Select mux mode: ALT3 mux port: RMII_CLKIN of instance: ccm. Used as MAC0-TXCLK when MAC0-MII is enabled.
#100 : 100
Select mux mode: ALT4 mux port: DATA_OUT[19] of instance: tcon0.
#110 : 110
Select mux mode: ALT6 mux port: IPP_WDOG_CA5_CM4_B of instance: wdog_glue.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 32
address_offset : 0x80 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[32] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: TX of instance: sci_flx0.
#100 : 100
Select mux mode: ALT4 mux port: TCON[4] of instance: tcon0.
#101 : 101
Select mux mode: ALT5 mux port: VIU_DE of instance: video_in0.
#110 : 110
CKO1
#111 : 111
Select mux mode: ALT7 mux port: ENET_TS_CLKIN of instance: ccm.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 32
address_offset : 0x80 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 33
address_offset : 0x84 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[33] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: RX of instance: sci_flx0.
#100 : 100
Select mux mode: ALT4 mux port: TCON[5] of instance: tcon0.
#101 : 101
Select mux mode: ALT5 mux port: SNVS_ALARM_OUT_B of instance: snvs_lp_wrapper.
#110 : 110
CKO2
#111 : 111
Select mux mode: ALT7 mux port: MAC0_TMR0 of instance: enet_swiahb.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 33
address_offset : 0x84 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 34
address_offset : 0x88 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 34
address_offset : 0x88 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[34] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: RTS of instance: sci_flx0.
#011 : 011
Select mux mode: ALT3 mux port: CS5 of instance: dspi0.
#100 : 100
Select mux mode: ALT4 mux port: TCON[6] of instance: tcon0.
#101 : 101
Select mux mode: ALT5 mux port: FB_AD[1] of instance: platform.
#111 : 111
Select mux mode: ALT7 mux port: MAC0_TMR1 of instance: enet_swiahb.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 35
address_offset : 0x8C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[35] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: CTS of instance: sci_flx0.
#011 : 011
Select mux mode: ALT3 mux port: CS4 of instance: dspi0.
#100 : 100
Select mux mode: ALT4 mux port: TCON[7] of instance: tcon0.
#101 : 101
Select mux mode: ALT5 mux port: FB_AD[0] of instance: platform.
#110 : 110
Select mux mode: ALT6 mux port: TRACECTL of instance: platform.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 35
address_offset : 0x8C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 36
address_offset : 0x90 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[36] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: RXD of instance: can0.
#010 : 010
Select mux mode: ALT2 mux port: SCL of instance: i2c0.
#100 : 100
Select mux mode: ALT4 mux port: TCON[8] of instance: tcon0.
#111 : 111
Select mux mode: ALT7 mux port: DATA_OUT[1] of instance: tcon1.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 36
address_offset : 0x90 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 37
address_offset : 0x94 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 37
address_offset : 0x94 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[37] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: TXD of instance: can0.
#010 : 010
Select mux mode: ALT2 mux port: SDA of instance: i2c0.
#100 : 100
Select mux mode: ALT4 mux port: TCON[9] of instance: tcon0.
#111 : 111
Select mux mode: ALT7 mux port: PIX_CLK of instance: video_in0.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 38
address_offset : 0x98 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 38
address_offset : 0x98 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[38] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: RXD of instance: can1.
#010 : 010
Select mux mode: ALT2 mux port: SCL of instance: i2c1.
#100 : 100
Select mux mode: ALT4 mux port: TCON[10] of instance: tcon0.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 39
address_offset : 0x9C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 39
address_offset : 0x9C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[39] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: TXD of instance: can1.
#010 : 010
Select mux mode: ALT2 mux port: SDA of instance: i2c1.
#100 : 100
Select mux mode: ALT4 mux port: TCON[11] of instance: tcon0.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 40
address_offset : 0xA0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[40] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: CS1 of instance: dspi0.
#010 : 010
Select mux mode: ALT2 mux port: EXT_AUDIO_MCLK of instance: ccm.
#100 : 100
CKO1
#110 : 110
Select mux mode: ALT6 mux port: DATA[9] of instance: video_in0.
#111 : 111
Reserved
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 40
address_offset : 0xA0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 41
address_offset : 0xA4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[41] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: CS0 of instance: dspi0.
#110 : 110
Select mux mode: ALT6 mux port: DATA[10] of instance: video_in0.
#111 : 111
Reserved
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 41
address_offset : 0xA4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 42
address_offset : 0xA8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[42] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: SIN of instance: dspi0.
#100 : 100
Select mux mode: ALT4 mux port: LCD42 of instance: lcd_64f6b.
#110 : 110
Select mux mode: ALT6 mux port: DATA[11] of instance: video_in0.
#111 : 111
Reserved
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 42
address_offset : 0xA8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 43
address_offset : 0xAC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[43] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: SOUT of instance: dspi0.
#100 : 100
Select mux mode: ALT4 mux port: LCD43 of instance: lcd_64f6b.
#110 : 110
Select mux mode: ALT6 mux port: DATA[12] of instance: video_in0.
#111 : 111
Select mux mode: ALT7 mux port: DATA_OUT[1] of instance: tcon1.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 43
address_offset : 0xAC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 44
address_offset : 0xB0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[44] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: SCK of instance: dspi0.
#101 : 101
Select mux mode: ALT5 mux port: VIU_FID of instance: video_in0.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 44
address_offset : 0xB0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 45
address_offset : 0xB4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[45] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: RMII0_MDC/MII0_MDC of instance: enet_swiahb.
#010 : 010
Select mux mode: ALT2 mux port: CH[0] of instance: flextimer1.
#011 : 011
Select mux mode: ALT3 mux port: CS3 of instance: dspi0.
#100 : 100
Select mux mode: ALT4 mux port: SCKT of instance: esai.
#101 : 101
Select mux mode: ALT5 mux port: CLK of instance: esdhc0.
#110 : 110
Select mux mode: ALT6 mux port: DATA[0] of instance: video_in0.
#111 : 111
Select mux mode: ALT7 mux port: RCON18 of instance: src.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 45
address_offset : 0xB4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 46
address_offset : 0xB8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[46] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: RMII0_MDIO/MII0_MDIO of instance: enet_swiahb.
#010 : 010
Select mux mode: ALT2 mux port: CH[1] of instance: flextimer1.
#011 : 011
Select mux mode: ALT3 mux port: CS2 of instance: dspi0.
#100 : 100
Select mux mode: ALT4 mux port: FST of instance: esai.
#101 : 101
Select mux mode: ALT5 mux port: CMD of instance: esdhc0.
#110 : 110
Select mux mode: ALT6 mux port: DATA[1] of instance: video_in0.
#111 : 111
Select mux mode: ALT7 mux port: RCON19 of instance: src.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 46
address_offset : 0xB8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 47
address_offset : 0xBC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 47
address_offset : 0xBC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[47] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: RMII0_RX_EN of instance: enet_swiahb.
#010 : 010
Select mux mode: ALT2 mux port: TX of instance: sci_flx1.
#100 : 100
Select mux mode: ALT4 mux port: SDO0 of instance: esai.
#101 : 101
Select mux mode: ALT5 mux port: DAT0 of instance: esdhc0.
#110 : 110
Select mux mode: ALT6 mux port: DATA[2] of instance: video_in0.
#111 : 111
Select mux mode: ALT7 mux port: RCON20 of instance: src.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 3
address_offset : 0xC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[3] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: TDO of instance: debug.
#010 : 010
Select mux mode: ALT2 mux port: EXT_AUDIO_MCLK of instance: ccm.
#100 : 100
Select mux mode: ALT4 mux port: DATA_OUT[10] of instance: tcon0.
#110 : 110
Select mux mode: ALT6 mux port: ENET_TS_CLKIN of instance: ccm.
#111 : 111
Select mux mode: ALT7 mux port: MLBSIGNAL of instance: mlb_top.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 3
address_offset : 0xC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 48
address_offset : 0xC0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 48
address_offset : 0xC0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[48] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: RMII0_RXD[1]//MII0_RXD[1] of instance: enet_swiahb.
#010 : 010
Select mux mode: ALT2 mux port: RX of instance: sci_flx1.
#100 : 100
Select mux mode: ALT4 mux port: SDO1 of instance: esai.
#101 : 101
Select mux mode: ALT5 mux port: DAT1 of instance: esdhc0.
#110 : 110
Select mux mode: ALT6 mux port: DATA[3] of instance: video_in0.
#111 : 111
Select mux mode: ALT7 mux port: DATA_OUT[18] of instance: tcon0.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 49
address_offset : 0xC4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[49] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: RMII0_RXD[0]/MII0_RXD[0] of instance: enet_swiahb.
#010 : 010
Select mux mode: ALT2 mux port: RTS of instance: sci_flx1.
#011 : 011
Select mux mode: ALT3 mux port: CS1 of instance: dspi1.
#100 : 100
Select mux mode: ALT4 mux port: SDO2 of instance: esai.
#101 : 101
Select mux mode: ALT5 mux port: DAT2 of instance: esdhc0.
#110 : 110
Select mux mode: ALT6 mux port: DATA[4] of instance: video_in0.
#111 : 111
Select mux mode: ALT7 mux port: DATA_OUT[19] of instance: tcon0.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 49
address_offset : 0xC4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 50
address_offset : 0xC8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 50
address_offset : 0xC8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[50] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: RMII0_RXER/MII0_RXER of instance: enet_swiahb.
#010 : 010
Select mux mode: ALT2 mux port: CTS of instance: sci_flx1.
#011 : 011
Select mux mode: ALT3 mux port: CS0 of instance: dspi1.
#100 : 100
Select mux mode: ALT4 mux port: SDO3 of instance: esai.
#101 : 101
Select mux mode: ALT5 mux port: DAT3 of instance: esdhc0.
#110 : 110
Select mux mode: ALT6 mux port: DATA[5] of instance: video_in0.
#111 : 111
Select mux mode: ALT7 mux port: DATA_OUT[10] of instance: tcon0.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 51
address_offset : 0xCC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 51
address_offset : 0xCC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[51] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: RMII0_TXD[1]/MII0_TXD[1] of instance: enet_swiahb.
#011 : 011
Select mux mode: ALT3 mux port: SIN of instance: dspi1.
#100 : 100
Select mux mode: ALT4 mux port: SDI0 of instance: esai.
#101 : 101
Select mux mode: ALT5 mux port: WP of instance: esdhc0.
#110 : 110
Select mux mode: ALT6 mux port: DATA[6] of instance: video_in0.
#111 : 111
Select mux mode: ALT7 mux port: DATA_OUT[11] of instance: tcon0.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 52
address_offset : 0xD0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 52
address_offset : 0xD0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[52] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: RMII0_TXD[0]/MII0_TXD[0] of instance: enet_swiahb.
#011 : 011
Select mux mode: ALT3 mux port: SOUT of instance: dspi1.
#100 : 100
Select mux mode: ALT4 mux port: SDI1 of instance: esai.
#110 : 110
Select mux mode: ALT6 mux port: DATA[7] of instance: video_in0.
#111 : 111
Select mux mode: ALT7 mux port: DATA_OUT[2] of instance: tcon0.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 53
address_offset : 0xD4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[53] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: RMII0_TXEN/MII0_TXEN of instance: enet_swiahb.
#011 : 011
Select mux mode: ALT3 mux port: SCK of instance: dspi1.
#110 : 110
Select mux mode: ALT6 mux port: DATA[8] of instance: video_in0.
#111 : 111
Select mux mode: ALT7 mux port: DATA_OUT[3] of instance: tcon0.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 53
address_offset : 0xD4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 54
address_offset : 0xD8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 54
address_offset : 0xD8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[54] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: RMII1_MDC of instance: enet_swiahb.
#011 : 011
Select mux mode: ALT3 mux port: SCKT of instance: esai.
#110 : 110
Select mux mode: ALT6 mux port: MLBCLK of instance: mlb_top.
#111 : 111
Select mux mode: ALT7 mux port: debug_out[0] of instance: viu_mux.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 55
address_offset : 0xDC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 55
address_offset : 0xDC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[55] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: RMII1_MDIO of instance: enet_swiahb.
#011 : 011
Select mux mode: ALT3 mux port: FST of instance: esai.
#110 : 110
Select mux mode: ALT6 mux port: MLBSIGNAL of instance: mlb_top.
#111 : 111
Select mux mode: ALT7 mux port: debug_out[1] of instance: viu_mux.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 56
address_offset : 0xE0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[56] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: RMII1_CRS_DV of instance: enet_swiahb.
#011 : 011
Select mux mode: ALT3 mux port: SDO0 of instance: esai.
#110 : 110
Select mux mode: ALT6 mux port: MLBDATA of instance: mlb_top.
#111 : 111
Select mux mode: ALT7 mux port: debug_out[2] of instance: viu_mux.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 56
address_offset : 0xE0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 57
address_offset : 0xE4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 57
address_offset : 0xE4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[57] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: RMII1_RXD[1] of instance: enet_swiahb.
#011 : 011
Select mux mode: ALT3 mux port: SDO1 of instance: esai.
#101 : 101
Select mux mode: ALT5 mux port: TX_BCLK of instance: sai2.
#111 : 111
Select mux mode: ALT7 mux port: debug_out[3] of instance: viu_mux.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 58
address_offset : 0xE8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 58
address_offset : 0xE8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[58] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: RMII1_RXD[0] of instance: enet_swiahb.
#011 : 011
Select mux mode: ALT3 mux port: SDO2 of instance: esai.
#101 : 101
Select mux mode: ALT5 mux port: RX_BCLK of instance: sai2.
#111 : 111
Select mux mode: ALT7 mux port: debug_out[4] of instance: viu_mux.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 59
address_offset : 0xEC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 59
address_offset : 0xEC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[59] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: RMII1_RXER of instance: enet_swiahb.
#011 : 011
Select mux mode: ALT3 mux port: SDO3 of instance: esai.
#100 : 100
Select mux mode: ALT4 mux port: TX of instance: sci_flx5.
#101 : 101
Select mux mode: ALT5 mux port: RX_DATA of instance: sai2.
#110 : 110
Select mux mode: ALT6 mux port: ADC0SE6 of instance: adc0_da.
#111 : 111
Select mux mode: ALT7 mux port: debug_out[5] of instance: viu_mux.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 60
address_offset : 0xF0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[60] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: RMII1_TXD[1] of instance: enet_swiahb.
#011 : 011
Select mux mode: ALT3 mux port: SDI0 of instance: esai.
#100 : 100
Select mux mode: ALT4 mux port: RX of instance: sci_flx5.
#101 : 101
Select mux mode: ALT5 mux port: TX_DATA of instance: sai2.
#110 : 110
Select mux mode: ALT6 mux port: ADC0SE7 of instance: adc0_da.
#111 : 111
Select mux mode: ALT7 mux port: debug_out[6] of instance: viu_mux.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 60
address_offset : 0xF0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 61
address_offset : 0xF4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[61] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: RMII1_TXD[0] of instance: enet_swiahb.
#011 : 011
Select mux mode: ALT3 mux port: SDI1 of instance: esai.
#100 : 100
Select mux mode: ALT4 mux port: RTS of instance: sci_flx5.
#101 : 101
Select mux mode: ALT5 mux port: RX_SYNC of instance: sai2.
#110 : 110
Select mux mode: ALT6 mux port: ADC1SE6 of instance: adc1_da.
#111 : 111
Select mux mode: ALT7 mux port: debug_out[7] of instance: viu_mux.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 61
address_offset : 0xF4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 62
address_offset : 0xF8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 62
address_offset : 0xF8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[62] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: RMII1_TXEN of instance: enet_swiahb.
#011 : 011
Select mux mode: ALT3 mux port: ADC1SE7 of instance: adc1_da.
#100 : 100
Select mux mode: ALT4 mux port: CTS of instance: sci_flx5.
#101 : 101
Select mux mode: ALT5 mux port: TX_SYNC of instance: sai2.
#110 : 110
Select mux mode: ALT6 mux port: USB1_SOF_PULSE of instance: usb.
#111 : 111
Select mux mode: ALT7 mux port: debug_out[8] of instance: viu_mux.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 63
address_offset : 0xFC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keeper enable
#1 : 1
Pull enable
End of enumeration elements list.
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pull/Keeper Disabled
#1 : 1
Pull/Keeper Enabled
End of enumeration elements list.
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#00 : 00
100 kOhm Pull Down
#01 : 01
47 kOhm Pull Up
#10 : 10
100 kOhm Pull Up
#11 : 11
22 kOhm Pull Up
End of enumeration elements list.
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
#000 : 000
output driver disabled;
#001 : 001
150 Ohm (240 Ohm if pad is DDR)
#010 : 010
75 Ohm (120 Ohm if pad is DDR)
#011 : 011
50 Ohm (80 Ohm if pad is DDR)
#100 : 100
37 Ohm (60 Ohm if pad is DDR)
#101 : 101
30 Ohm (48 Ohm if pad is DDR)
#110 : 110
25 Ohm
#111 : 111
20 Ohm (34 Ohm if pad is DDR)
End of enumeration elements list.
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
CMOS input
#1 : 1
Schmitt trigger input
End of enumeration elements list.
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Output is CMOS
#1 : 1
Output is open drain
End of enumeration elements list.
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Slow Slew Rate
#1 : 1
Fast Slew Rate
End of enumeration elements list.
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
#00 : 00
Low (50 MHz)
#01 : 01
Medium (100 MHz)
#10 : 10
Medium (100 MHz)
#11 : 11
High (200 MHz)
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
Enumeration:
#000 : 000
Select mux mode: ALT0 mux port: GPIO[63] of instance: rgpioc.
#001 : 001
Select mux mode: ALT1 mux port: FB_AD[31] of instance: platform.
#010 : 010
Select mux mode: ALT2 mux port: NF_IO[15] of instance: nfc_mlc.
#100 : 100
Select mux mode: ALT4 mux port: CH[0] of instance: flextimer3.
#101 : 101
Select mux mode: ALT5 mux port: CS1 of instance: dspi2.
#111 : 111
Select mux mode: ALT7 mux port: debug_out[9] of instance: viu_mux.
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Software MUX Pad Control Register 63
address_offset : 0xFC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
alternate_register : IOMUXC
reset_Mask : 0x0
IBE : no description available
bits : 0 - 0 (1 bit)
access : read-write
OBE : no description available
bits : 1 - 1 (1 bit)
access : read-write
PUE : no description available
bits : 2 - 2 (1 bit)
access : read-write
PKE : no description available
bits : 3 - 3 (1 bit)
access : read-write
PUS : no description available
bits : 4 - 5 (2 bit)
access : read-write
DSE : no description available
bits : 6 - 8 (3 bit)
access : read-write
HYS : no description available
bits : 9 - 9 (1 bit)
access : read-write
ODE : no description available
bits : 10 - 10 (1 bit)
access : read-write
SRE : no description available
bits : 11 - 11 (1 bit)
access : read-write
SPEED : no description available
bits : 12 - 13 (2 bit)
access : read-write
RESERVED : no description available
bits : 14 - 19 (6 bit)
access : read-write
MUX_MODE : no description available
bits : 20 - 22 (3 bit)
access : read-write
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-write
Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !
This website is sponsored by Embeetle, an IDE designed from scratch for embedded software developers.