Embeetle, an IDE designed from scratch for embedded software developers.address_offset : 0x0 Bytes (0x0)
size : 0xB4 byte (0x0)
mem_usage : registers
protection : not protected
USB0 VBUS Detect control register
address_offset : 0x0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
VBUSVALID_THRESH : no description available
bits : 0 - 2 (3 bit)
access : read-write
Enumeration:
#000 : 000
4.0 V
#001 : 001
4.1 V
#010 : 010
4.2 V
#011 : 011
4.3 V
#100 : 100
4.4 V (default)
#101 : 101
4.5 V
#110 : 110
4.6 V
#111 : 111
4.7 V
End of enumeration elements list.
VBUS_OVERRIDE_EN : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Use hardware generated values
#1 : 1
Use the software controlled values.
End of enumeration elements list.
SESSEND_OVERRIDE : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
SESSEND hardware signal is not overrided
#1 : 1
Override value for the SESSEND hardware signal
End of enumeration elements list.
BVALID_OVERRIDE : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
BVALID hardware signal is not overrided
#1 : 1
Override value for the BVALID hardware signal
End of enumeration elements list.
AVALID_OVERRIDE : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
AVALID hardware signal is not overrided
#1 : 1
Override value for the AVALID hardware signal
End of enumeration elements list.
VBUSVALID_OVERRIDE : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
Value for the VBUSVALID hardware signal is not overrided
#1 : 1
Override value for the VBUSVALID hardware signal.
End of enumeration elements list.
RESERVED : no description available
bits : 8 - 17 (10 bit)
access : read-only
VBUSVALID_TO_B : no description available
bits : 18 - 18 (1 bit)
access : read-write
Enumeration:
#0 : 0
Multiplexing of the Bvalid comparator to the VBUSVALID comparator is not enabled
#1 : 1
Enable multiplexing of the Bvalid comparator to the VBUSVALID comparator
End of enumeration elements list.
RESERVED : no description available
bits : 19 - 19 (1 bit)
access : read-only
VBUSVALID_PWRUP_CMPS : no description available
bits : 20 - 20 (1 bit)
access : read-write
Enumeration:
#0 : 0
Powering up comparators for VBUS_valid detector is not enabled
#1 : 1
Enable powering up comparators for VBUS_valid detector.
End of enumeration elements list.
RESERVED : no description available
bits : 21 - 25 (5 bit)
access : read-only
DISCHARGE_VBUS : no description available
bits : 26 - 26 (1 bit)
access : read-write
Enumeration:
#0 : 0
Discharging of the VBUS is not enabled
#1 : 1
Enable discharging of the VBUS
End of enumeration elements list.
CHARGE_VBUS : USB OTG charge VBUS.
bits : 27 - 27 (1 bit)
access : read-write
Enumeration:
#0 : 0
Charging of the VBUS is not enabled
#1 : 1
Enable charging of the VBUS
End of enumeration elements list.
RESERVED : no description available
bits : 28 - 30 (3 bit)
access : read-only
EN_CHARGER_RESISTOR : no description available
bits : 31 - 31 (1 bit)
access : read-write
Enumeration:
#0 : 0
125k pullup on USB_DP and 375k on USB_DM to provide USB_CHARGER functionality for USB is not enabled
#1 : 1
Enable 125k pullup on USB_DP and 375k on USB_DM to provide USB_CHARGER functionality for USB
End of enumeration elements list.
USB0 Charger Detect control register
address_offset : 0x10 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FORCE_DETECT : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
The charger detector circuit is not forced to signal the presence of a charger.
#1 : 1
Force the charger detector circuit to signal the presence of a charger.
End of enumeration elements list.
RESERVED : no description available
bits : 1 - 17 (17 bit)
access : read-only
CHK_CONTACT : This bit checks whether the USB plug has been in contact with each other.
bits : 18 - 18 (1 bit)
access : read-write
Enumeration:
#0 : 0
Do not check the contact of USB plug.
#1 : 1
Check whether the USB plug has been in contact with each other.
End of enumeration elements list.
CHK_CHRG_B : This bit checks whether a charger (either a dedicated charger or a host charger) is connected to USB port.
bits : 19 - 19 (1 bit)
access : read-write
Enumeration:
#0 : 0
Check whether a charger (either a dedicated charger or a host charger) is connected to USB port.
#1 : 1
Do not check whether a charger is connected to the USB port.
End of enumeration elements list.
EN_B : This bit enables the charger detector.
bits : 20 - 20 (1 bit)
access : read-write
Enumeration:
#0 : 0
Enable the charger detector.
#1 : 1
Disable the charger detector.
End of enumeration elements list.
CHRG_DET_STATUS : no description available
bits : 21 - 21 (1 bit)
access : read-only
Enumeration:
#0 : 0
Charger not detected.
#1 : 1
Charger detected.
End of enumeration elements list.
CHRG_DET_CTRL : no description available
bits : 22 - 22 (1 bit)
access : read-write
Enumeration:
#0 : 0
USB battery charging v1.1 device charger detection functionality is not enabled
#1 : 1
Enable basic USB battery charging v1.1 device charger detection functionality
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 23 (1 bit)
access : read-only
RESERVED : no description available
bits : 24 - 31 (8 bit)
access : read-only
USB0 VBUS Detect Status definition register
address_offset : 0x20 Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
SESSEND : no description available
bits : 0 - 0 (1 bit)
access : read-only
Enumeration:
#0 : 0
VDD5V is present.
#1 : 1
VDD5V is not present.
End of enumeration elements list.
BVALID : no description available
bits : 1 - 1 (1 bit)
access : read-only
Enumeration:
#0 : 0
VBUS is not valid for USB B-session
#1 : 1
VBUS valid for USB B-session
End of enumeration elements list.
AVALID : no description available
bits : 2 - 2 (1 bit)
access : read-only
Enumeration:
#0 : 0
VBUS is not valid for a A-peripheral
#1 : 1
VBUS is valid for a A-peripheral
End of enumeration elements list.
VBUS_VALID : no description available
bits : 3 - 3 (1 bit)
access : read-only
Enumeration:
#0 : 0
VBUS not valid for USB OTG
#1 : 1
VBUS valid for USB OTG
End of enumeration elements list.
RESERVED : no description available
bits : 4 - 31 (28 bit)
access : read-only
USB0 Charger Detect Status definition register
address_offset : 0x30 Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
PLUG_CONTACT : This bit shows the contact status of the USB plug.
bits : 0 - 0 (1 bit)
access : read-only
Enumeration:
#0 : 0
The USB plug has not been contacted.
#1 : 1
The USB plug has made good contact.
End of enumeration elements list.
CHRG_DETECTED : no description available
bits : 1 - 1 (1 bit)
access : read-only
Enumeration:
#0 : 0
The USB port is not connected to a charger.
#1 : 1
A charger (either a dedicated charger or a host charger) is connected to the USB port.
End of enumeration elements list.
DM_STATE : no description available
bits : 2 - 2 (1 bit)
access : read-only
DP_STATE : no description available
bits : 3 - 3 (1 bit)
access : read-only
RESERVED : no description available
bits : 4 - 31 (28 bit)
access : read-only
USB0 Loopback register
address_offset : 0x40 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
UTMI_TESTSTART : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
USB0 loopback test is not enabled.
#1 : 1
Enable USB0 loopback test.
End of enumeration elements list.
UTMI_DIG_TST0 : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
USB0 loopback test 0 is not enabled.
#1 : 1
Enable USB0 loopback test 0.
End of enumeration elements list.
UTMI_DIG_TST1 : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
USB0 loopback test 1 is not enabled.
#1 : 1
Enable USB0 loopback test 1.
End of enumeration elements list.
TSTI_TX_HS_MODE : Chooses HS or FS mode for USB0.
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
USB0 FS mode.
#1 : 1
USB0 HS mode.
End of enumeration elements list.
TSTI_TX_LS_MODE : Chooses LS mode for USB0.
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
Choose HS or FS mode which is defined by TSTI1_TX_HS.
#1 : 1
Choose LS for USB0.
End of enumeration elements list.
TSTI_TX_EN : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
TX for USB0 is not enabled.
#1 : 1
Enable TX for USB0.
End of enumeration elements list.
TSTI_TX_HIZ : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
TX is not HIZ for USB0.
#1 : 1
Make TX HIZ for USB0.
End of enumeration elements list.
UTMO_DIG_TST0 : no description available
bits : 7 - 7 (1 bit)
access : read-only
Enumeration:
#0 : 0
Not pass
#1 : 1
Pass
End of enumeration elements list.
UTMO_DIG_TST1 : no description available
bits : 8 - 8 (1 bit)
access : read-only
Enumeration:
#0 : 0
Pass
#1 : 1
Not pass
End of enumeration elements list.
RESERVED : no description available
bits : 9 - 31 (23 bit)
access : read-only
USB0 Miscellaneous definition register
address_offset : 0x50 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
HS_USE_EXTERNAL_R : no description available
bits : 0 - 0 (1 bit)
access : read-write
EN_DEGLITCH : no description available
bits : 1 - 1 (1 bit)
access : read-write
RESERVED : no description available
bits : 2 - 23 (22 bit)
access : read-only
RESERVED : no description available
bits : 24 - 24 (1 bit)
access : read-only
RESERVED : no description available
bits : 25 - 25 (1 bit)
access : read-only
RESERVED : no description available
bits : 26 - 26 (1 bit)
access : read-only
RESERVED : no description available
bits : 27 - 27 (1 bit)
access : read-only
RESERVED : no description available
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : no description available
bits : 29 - 29 (1 bit)
access : read-only
EN_CLK_TO_UTMI : no description available
bits : 30 - 30 (1 bit)
access : read-write
RESERVED : no description available
bits : 31 - 31 (1 bit)
access : read-only
USB1 VBUS Detect control register
address_offset : 0x60 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
VBUSVALID_THRESH : no description available
bits : 0 - 2 (3 bit)
access : read-write
Enumeration:
#000 : 000
4.0 V
#001 : 001
4.1 V
#010 : 010
4.2 V
#011 : 011
4.3 V
#100 : 100
4.4 V (default)
#101 : 101
4.5 V
#110 : 110
4.6 V
#111 : 111
4.7 V
End of enumeration elements list.
VBUS_OVERRIDE_EN : no description available
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Use hardware generated values
#1 : 1
Use the software controlled values.
End of enumeration elements list.
SESSEND_OVERRIDE : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
SESSEND hardware signal is not overrided
#1 : 1
Override value for the SESSEND hardware signal
End of enumeration elements list.
BVALID_OVERRIDE : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
BVALID hardware signal is not overrided
#1 : 1
Override value for the BVALID hardware signal
End of enumeration elements list.
AVALID_OVERRIDE : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
AVALID hardware signal is not overrided
#1 : 1
Override value for the AVALID hardware signal
End of enumeration elements list.
VBUSVALID_OVERRIDE : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
Value for the VBUSVALID hardware signal is not overrided
#1 : 1
Override value for the VBUSVALID hardware signal.
End of enumeration elements list.
RESERVED : no description available
bits : 8 - 17 (10 bit)
access : read-only
VBUSVALID_TO_B : no description available
bits : 18 - 18 (1 bit)
access : read-write
Enumeration:
#0 : 0
Multiplexing of the Bvalid comparator to the VBUSVALID comparator is not enabled
#1 : 1
Enable multiplexing of the Bvalid comparator to the VBUSVALID comparator
End of enumeration elements list.
RESERVED : no description available
bits : 19 - 19 (1 bit)
access : read-only
VBUSVALID_PWRUP_CMPS : no description available
bits : 20 - 20 (1 bit)
access : read-write
Enumeration:
#0 : 0
Powering up comparators for VBUS_valid detector is not enabled
#1 : 1
Enable powering up comparators for VBUS_valid detector.
End of enumeration elements list.
RESERVED : no description available
bits : 21 - 25 (5 bit)
access : read-only
DISCHARGE_VBUS : no description available
bits : 26 - 26 (1 bit)
access : read-write
Enumeration:
#0 : 0
Discharging of the VBUS is not enabled
#1 : 1
Enable discharging of the VBUS
End of enumeration elements list.
CHARGE_VBUS : USB OTG charge VBUS.
bits : 27 - 27 (1 bit)
access : read-write
Enumeration:
#0 : 0
Charging of the VBUS is not enabled
#1 : 1
Enable charging of the VBUS
End of enumeration elements list.
RESERVED : no description available
bits : 28 - 30 (3 bit)
access : read-only
EN_CHARGER_RESISTOR : no description available
bits : 31 - 31 (1 bit)
access : read-write
Enumeration:
#0 : 0
125k pullup on USB_DP and 375k on USB_DM to provide USB_CHARGER functionality for USB is not enabled
#1 : 1
Enable 125k pullup on USB_DP and 375k on USB_DM to provide USB_CHARGER functionality for USB
End of enumeration elements list.
USB1 Charger Detect control register
address_offset : 0x70 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FORCE_DETECT : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
The charger detector circuit is not forced to signal the presence of a charger.
#1 : 1
Force the charger detector circuit to signal the presence of a charger.
End of enumeration elements list.
RESERVED : no description available
bits : 1 - 17 (17 bit)
access : read-only
CHK_CONTACT : This bit checks whether the USB plug has been in contact with each other.
bits : 18 - 18 (1 bit)
access : read-write
Enumeration:
#0 : 0
Do not check the contact of USB plug.
#1 : 1
Check whether the USB plug has been in contact with each other.
End of enumeration elements list.
CHK_CHRG_B : This bit checks whether a charger (either a dedicated charger or a host charger) is connected to USB port.
bits : 19 - 19 (1 bit)
access : read-write
Enumeration:
#0 : 0
Check whether a charger (either a dedicated charger or a host charger) is connected to USB port.
#1 : 1
Do not check whether a charger is connected to the USB port.
End of enumeration elements list.
EN_B : This bit enables the charger detector.
bits : 20 - 20 (1 bit)
access : read-write
Enumeration:
#0 : 0
Enable the charger detector.
#1 : 1
Disable the charger detector.
End of enumeration elements list.
CHRG_DET_STATUS : no description available
bits : 21 - 21 (1 bit)
access : read-only
Enumeration:
#0 : 0
Charger not detected.
#1 : 1
Charger detected.
End of enumeration elements list.
CHRG_DET_CTRL : no description available
bits : 22 - 22 (1 bit)
access : read-write
Enumeration:
#0 : 0
USB battery charging v1.1 device charger detection functionality is not enabled
#1 : 1
Enable basic USB battery charging v1.1 device charger detection functionality
End of enumeration elements list.
RESERVED : no description available
bits : 23 - 23 (1 bit)
access : read-only
RESERVED : no description available
bits : 24 - 31 (8 bit)
access : read-only
USB1 VBUS Detect STS definition register
address_offset : 0x80 Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
SESSEND : no description available
bits : 0 - 0 (1 bit)
access : read-only
Enumeration:
#0 : 0
VDD5V is present.
#1 : 1
VDD5V is not present.
End of enumeration elements list.
BVALID : no description available
bits : 1 - 1 (1 bit)
access : read-only
Enumeration:
#0 : 0
VBUS is not valid for USB B-session
#1 : 1
VBUS valid for USB B-session
End of enumeration elements list.
AVALID : no description available
bits : 2 - 2 (1 bit)
access : read-only
Enumeration:
#0 : 0
VBUS is not valid for a A-peripheral
#1 : 1
VBUS is valid for a A-peripheral
End of enumeration elements list.
VBUS_VALID : no description available
bits : 3 - 3 (1 bit)
access : read-only
Enumeration:
#0 : 0
VBUS not valid for USB OTG
#1 : 1
VBUS valid for USB OTG
End of enumeration elements list.
RESERVED : no description available
bits : 4 - 31 (28 bit)
access : read-only
USB1 Charger Detect Status definition register
address_offset : 0x90 Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
PLUG_CONTACT : This bit shows the contact status of the USB plug.
bits : 0 - 0 (1 bit)
access : read-only
Enumeration:
#0 : 0
The USB plug has not been contacted.
#1 : 1
The USB plug has made good contact.
End of enumeration elements list.
CHRG_DETECTED : no description available
bits : 1 - 1 (1 bit)
access : read-only
Enumeration:
#0 : 0
The USB port is not connected to a charger.
#1 : 1
A charger (either a dedicated charger or a host charger) is connected to the USB port.
End of enumeration elements list.
DM_STATE : no description available
bits : 2 - 2 (1 bit)
access : read-only
DP_STATE : no description available
bits : 3 - 3 (1 bit)
access : read-only
RESERVED : no description available
bits : 4 - 31 (28 bit)
access : read-only
USB1 Loopback register
address_offset : 0xA0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
UTMI_TESTSTART : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
USB1 loopback test is not enabled.
#1 : 1
Enable USB1 loopback test.
End of enumeration elements list.
UTMI_DIG_TST0 : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
USB1 loopback test 0 is not enabled.
#1 : 1
Enable USB1 loopback test 0.
End of enumeration elements list.
UTMI_DIG_TST1 : no description available
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
USB1 loopback test 1 is not enabled.
#1 : 1
Enable USB1 loopback test 1.
End of enumeration elements list.
TSTI_TX_HS_MODE : Chooses HS or FS mode for USB1.
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
USB1 FS mode.
#1 : 1
USB1 HS mode.
End of enumeration elements list.
TSTI_TX_LS_MODE : Chooses LS mode for USB1.
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
Choose HS or FS mode which is defined by TSTI1_TX_HS.
#1 : 1
Choose LS for USB1.
End of enumeration elements list.
TSTI_TX_EN : no description available
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
TX for USB1 is not enabled.
#1 : 1
Enable TX for USB1.
End of enumeration elements list.
TSTI_TX_HIZ : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
TX is not HIZ for USB1.
#1 : 1
Make TX HIZ for USB1.
End of enumeration elements list.
UTM1_DIG_TST0 : no description available
bits : 7 - 7 (1 bit)
access : read-only
Enumeration:
#0 : 0
Not pass
#1 : 1
Pass
End of enumeration elements list.
UTM1_DIG_TST1 : no description available
bits : 8 - 8 (1 bit)
access : read-only
Enumeration:
#0 : 0
Pass
#1 : 1
Not pass
End of enumeration elements list.
RESERVED : no description available
bits : 9 - 31 (23 bit)
access : read-only
USB1 Miscellaneous definition register
address_offset : 0xB0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
HS_USE_EXTERNAL_R : no description available
bits : 0 - 0 (1 bit)
access : read-write
EN_DEGLITCH : no description available
bits : 1 - 1 (1 bit)
access : read-write
RESERVED : no description available
bits : 2 - 23 (22 bit)
access : read-only
RESERVED : no description available
bits : 24 - 24 (1 bit)
access : read-only
RESERVED : no description available
bits : 25 - 25 (1 bit)
access : read-only
RESERVED : no description available
bits : 26 - 26 (1 bit)
access : read-only
RESERVED : no description available
bits : 27 - 27 (1 bit)
access : read-only
RESERVED : no description available
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : no description available
bits : 29 - 29 (1 bit)
access : read-only
EN_CLK_TO_UTMI : no description available
bits : 30 - 30 (1 bit)
access : read-write
RESERVED : no description available
bits : 31 - 31 (1 bit)
access : read-only
Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !
This website is sponsored by Embeetle, an IDE designed from scratch for embedded software developers.