\n
address_offset : 0x0 Bytes (0x0)
size : 0x410 byte (0x0)
mem_usage : registers
protection : not protected
Module Configuration Register
address_offset : 0x0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
SWRSTSD : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
No action
#1 : 1
Serial Flash domain flops are reset. Does not reset configuration registers. It is advisable to reset both the serial flash domain and AHB domain at the same time. Resetting only one domain might lead to side effects.
End of enumeration elements list.
SWRSTHD : no description available
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
No action
#1 : 1
AHB domain flops are reset. Does not reset configuration registers. It is advisable to reset both the serial flash domain and AHB domain at the same time. Resetting only one domain might lead to side effects.
End of enumeration elements list.
END_CFG : no description available
bits : 2 - 3 (2 bit)
access : read-write
RESERVED : no description available
bits : 4 - 5 (2 bit)
access : read-only
DQS_EN : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
DQS disabled.
#1 : 1
DQS enabled- When enabled, the incoming data is sampled on both the edges of DQS input. The QSPI_SMPR[DDR_SMP] values are ignored.
End of enumeration elements list.
DDR_EN : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
2x and 4x clocks are disabled for SDR instructions only
#1 : 1
2x and 4x clocks are enabled supports both SDR and DDR instruction.
End of enumeration elements list.
RESERVED : no description available
bits : 8 - 9 (2 bit)
access : read-only
CLR_RXF : no description available
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
No action.
#1 : 1
Read and write pointers of the RX Buffer are reset to 0. QSPI_RBSR[RDBFL] is reset to 0.
End of enumeration elements list.
CLR_TXF : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
No action.
#1 : 1
Read and write pointers of the TX Buffer are reset to 0. QSPI_TBSR[TRCTR] is reset to 0.
End of enumeration elements list.
RESERVED : no description available
bits : 12 - 13 (2 bit)
access : read-only
MDIS : no description available
bits : 14 - 14 (1 bit)
access : read-write
Enumeration:
#0 : 0
Enable QuadSPI clocks.
#1 : 1
Allow external logic to disable QuadSPI clocks.
End of enumeration elements list.
RESERVED : no description available
bits : 15 - 15 (1 bit)
access : read-write
RESERVED : no description available
bits : 16 - 19 (4 bit)
access : read-write
RESERVED : no description available
bits : 20 - 23 (4 bit)
access : read-only
RESERVED : no description available
bits : 24 - 31 (8 bit)
access : read-write
Buffer0 Configuration Register
address_offset : 0x10 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MSTRID : no description available
bits : 0 - 3 (4 bit)
access : read-write
RESERVED : no description available
bits : 4 - 7 (4 bit)
access : read-only
ADATSZ : no description available
bits : 8 - 15 (8 bit)
access : read-write
RESERVED : no description available
bits : 16 - 30 (15 bit)
access : read-only
HP_EN : no description available
bits : 31 - 31 (1 bit)
access : read-write
Serial Flash Address Register
address_offset : 0x100 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
SFADR : no description available
bits : 0 - 31 (32 bit)
access : read-write
RX Buffer Data Register
address_offset : 0x1054 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RXDATA : no description available
bits : 0 - 31 (32 bit)
access : read-write
Sampling Register
address_offset : 0x108 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
HSENA : Half Speed serial flash clock Enable: This bit enables the divide by 2 of the clock to the external serial flash device for all commands,both SDR and DDR. Refer to Serial Flash Clock Frequency Limitations for details.
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disable divide by 2 of serial flash clock for half speed commands
#1 : 1
Enable divide by 2 of serial flash clock for half speed commands
End of enumeration elements list.
HSPHS : Half Speed Phase selection for SDR instructions.
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Select sampling at non-inverted clock
#1 : 1
Select sampling at inverted clock
End of enumeration elements list.
HSDLY : Half Speed Delay selection for SDR instructions.
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
One clock cycle delay
#1 : 1
Two clock cycle delay
End of enumeration elements list.
RESERVED : no description available
bits : 3 - 4 (2 bit)
access : read-only
FSPHS : Full Speed Phase selection for SDR instructions.
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
Select sampling at non-inverted clock
#1 : 1
Select sampling at inverted clock. This bit is ignored when using DDR instructions.
End of enumeration elements list.
FSDLY : Full Speed Delay selection for SDR instructions. Select the delay with respect to the reference edge for the sample point valid for full speed commands:
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
One clock cycle delay
#1 : 1
Two clock cycles delay. This bit is ignored when using DDR instructions
End of enumeration elements list.
RESERVED : no description available
bits : 7 - 15 (9 bit)
access : read-only
DDRSMP : no description available
bits : 16 - 18 (3 bit)
access : read-write
RESERVED : no description available
bits : 19 - 31 (13 bit)
access : read-only
RX Buffer Status Register
address_offset : 0x10C Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
RESERVED : no description available
bits : 0 - 7 (8 bit)
access : read-only
RDBFL : no description available
bits : 8 - 13 (6 bit)
access : read-only
RESERVED : no description available
bits : 14 - 15 (2 bit)
access : read-only
RDCTR : no description available
bits : 16 - 31 (16 bit)
access : read-only
RX Buffer Control Register
address_offset : 0x110 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
WMRK : no description available
bits : 0 - 4 (5 bit)
access : read-write
RESERVED : no description available
bits : 5 - 7 (3 bit)
access : read-only
RXBRD : no description available
bits : 8 - 8 (1 bit)
access : read-write
Enumeration:
#0 : 0
RX Buffer content is read using the AHB Bus registers QSPI_ARDB0 to QSPI_ARDB31. For details, refer to Exclusive Access to Serial Flash for AHB Commands.
#1 : 1
RX Buffer content is read using the IP Bus registers QSPI_RBDR0 to QSPI_RBDR31.
End of enumeration elements list.
RESERVED : no description available
bits : 9 - 31 (23 bit)
access : read-only
RX Buffer Data Register
address_offset : 0x1270 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RXDATA : no description available
bits : 0 - 31 (32 bit)
access : read-write
Look-up Table register
address_offset : 0x12B8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OPRND0 : Operand for INSTR0.
bits : 0 - 7 (8 bit)
access : read-write
PAD0 : Pad information for INSTR0.
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR0 : Instruction 0
bits : 10 - 15 (6 bit)
access : read-write
OPRND1 : Operand for INSTR1.
bits : 16 - 23 (8 bit)
access : read-write
PAD1 : Pad information for INSTR1.
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR1 : Instruction 1
bits : 26 - 31 (6 bit)
access : read-write
Buffer1 Configuration Register
address_offset : 0x14 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MSTRID : no description available
bits : 0 - 3 (4 bit)
access : read-write
RESERVED : no description available
bits : 4 - 7 (4 bit)
access : read-only
ADATSZ : no description available
bits : 8 - 15 (8 bit)
access : read-write
RESERVED : no description available
bits : 16 - 31 (16 bit)
access : read-only
RX Buffer Data Register
address_offset : 0x1490 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RXDATA : no description available
bits : 0 - 31 (32 bit)
access : read-write
TX Buffer Status Register
address_offset : 0x150 Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
RESERVED : no description available
bits : 0 - 7 (8 bit)
access : read-only
TRBFL : no description available
bits : 8 - 12 (5 bit)
access : read-only
RESERVED : no description available
bits : 13 - 15 (3 bit)
access : read-only
TRCTR : no description available
bits : 16 - 31 (16 bit)
access : read-only
TX Buffer Data Register
address_offset : 0x154 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TXDATA : no description available
bits : 0 - 31 (32 bit)
access : read-write
Status Register
address_offset : 0x15C Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
BUSY : no description available
bits : 0 - 0 (1 bit)
access : read-only
IP_ACC : no description available
bits : 1 - 1 (1 bit)
access : read-only
AHB_ACC : no description available
bits : 2 - 2 (1 bit)
access : read-only
RESERVED : no description available
bits : 3 - 3 (1 bit)
access : read-only
RESERVED : no description available
bits : 4 - 4 (1 bit)
access : read-only
AHBGNT : no description available
bits : 5 - 5 (1 bit)
access : read-only
AHBTRN : no description available
bits : 6 - 6 (1 bit)
access : read-only
AHB0NE : no description available
bits : 7 - 7 (1 bit)
access : read-only
AHB1NE : no description available
bits : 8 - 8 (1 bit)
access : read-only
AHB2NE : no description available
bits : 9 - 9 (1 bit)
access : read-only
AHB3NE : no description available
bits : 10 - 10 (1 bit)
access : read-only
AHB0FUL : no description available
bits : 11 - 11 (1 bit)
access : read-only
AHB1FUL : no description available
bits : 12 - 12 (1 bit)
access : read-only
AHB2FUL : no description available
bits : 13 - 13 (1 bit)
access : read-only
AHB3FUL : no description available
bits : 14 - 14 (1 bit)
access : read-only
RESERVED : no description available
bits : 15 - 15 (1 bit)
access : read-only
RXWE : no description available
bits : 16 - 16 (1 bit)
access : read-only
RESERVED : no description available
bits : 17 - 18 (2 bit)
access : read-only
RXFULL : no description available
bits : 19 - 19 (1 bit)
access : read-only
RESERVED : no description available
bits : 20 - 22 (3 bit)
access : read-only
RXDMA : no description available
bits : 23 - 23 (1 bit)
access : read-only
TXNE : no description available
bits : 24 - 24 (1 bit)
access : read-only
RESERVED : no description available
bits : 25 - 26 (2 bit)
access : read-only
TXFULL : no description available
bits : 27 - 27 (1 bit)
access : read-only
RESERVED : no description available
bits : 28 - 28 (1 bit)
access : read-only
DLPSMP : no description available
bits : 29 - 31 (3 bit)
access : read-only
Look-up Table register
address_offset : 0x15E4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OPRND0 : Operand for INSTR0.
bits : 0 - 7 (8 bit)
access : read-write
PAD0 : Pad information for INSTR0.
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR0 : Instruction 0
bits : 10 - 15 (6 bit)
access : read-write
OPRND1 : Operand for INSTR1.
bits : 16 - 23 (8 bit)
access : read-write
PAD1 : Pad information for INSTR1.
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR1 : Instruction 1
bits : 26 - 31 (6 bit)
access : read-write
Flag Register
address_offset : 0x160 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TFF : no description available
bits : 0 - 0 (1 bit)
access : read-write
RESERVED : no description available
bits : 1 - 3 (3 bit)
access : read-only
IPGEF : no description available
bits : 4 - 4 (1 bit)
access : read-write
RESERVED : no description available
bits : 5 - 5 (1 bit)
access : read-only
IPIEF : no description available
bits : 6 - 6 (1 bit)
access : read-write
IPAEF : no description available
bits : 7 - 7 (1 bit)
access : read-write
RESERVED : no description available
bits : 8 - 10 (3 bit)
access : read-only
IUEF : no description available
bits : 11 - 11 (1 bit)
access : read-write
ABOF : no description available
bits : 12 - 12 (1 bit)
access : read-write
AIBSEF : no description available
bits : 13 - 13 (1 bit)
access : read-write
AITEF : no description available
bits : 14 - 14 (1 bit)
access : read-write
ABSEF : no description available
bits : 15 - 15 (1 bit)
access : read-write
RBDF : no description available
bits : 16 - 16 (1 bit)
access : read-write
RBOF : no description available
bits : 17 - 17 (1 bit)
access : read-write
RESERVED : no description available
bits : 18 - 22 (5 bit)
access : read-only
ILLINE : no description available
bits : 23 - 23 (1 bit)
access : read-write
RESERVED : no description available
bits : 24 - 25 (2 bit)
access : read-only
TBUF : no description available
bits : 26 - 26 (1 bit)
access : read-write
TBFF : no description available
bits : 27 - 27 (1 bit)
access : read-write
RESERVED : no description available
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : no description available
bits : 29 - 30 (2 bit)
access : read-only
DLPFF : no description available
bits : 31 - 31 (1 bit)
access : read-write
Interrupt and DMA Request Select and Enable Register
address_offset : 0x164 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TFIE : no description available
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
No TFF interrupt will be generated
#1 : 1
TFF interrupt will be generated
End of enumeration elements list.
RESERVED : no description available
bits : 1 - 3 (3 bit)
access : read-only
IPGEIE : no description available
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
No IPGEF interrupt will be generated
#1 : 1
IPGEF interrupt will be generated
End of enumeration elements list.
RESERVED : no description available
bits : 5 - 5 (1 bit)
access : read-only
IPIEIE : no description available
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
No IPIEF interrupt will be generated
#0 : 0
IPIEF interrupt will be generated
End of enumeration elements list.
IPAEIE : no description available
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
No IPAEF interrupt will be generated
#1 : 1
IPAEF interrupt will be generated
End of enumeration elements list.
RESERVED : no description available
bits : 8 - 10 (3 bit)
access : read-only
IUEIE : no description available
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
No IUEF interrupt will be generated
#1 : 1
IUEF interrupt will be generated
End of enumeration elements list.
ABOIE : no description available
bits : 12 - 12 (1 bit)
access : read-write
Enumeration:
#0 : 0
No ABOF interrupt will be generated
#1 : 1
ABOF interrupt will be generated
End of enumeration elements list.
AIBSIE : no description available
bits : 13 - 13 (1 bit)
access : read-write
Enumeration:
#0 : 0
No AIBSEF interrupt will be generated
#1 : 1
AIBSEF interrupt will be generated
End of enumeration elements list.
AITIE : no description available
bits : 14 - 14 (1 bit)
access : read-write
Enumeration:
#0 : 0
No AITEF interrupt will be generated
#1 : 1
AITEF interrupt will be generated
End of enumeration elements list.
ABSEIE : no description available
bits : 15 - 15 (1 bit)
access : read-write
Enumeration:
#0 : 0
No ABSEF interrupt will be generated
#1 : 1
ABSEF interrupt will be generated
End of enumeration elements list.
RBDIE : no description available
bits : 16 - 16 (1 bit)
access : read-write
Enumeration:
#0 : 0
No RBDF interrupt will be generated
#1 : 1
RBDF Interrupt will be generated
End of enumeration elements list.
RBOIE : no description available
bits : 17 - 17 (1 bit)
access : read-write
Enumeration:
#0 : 0
No RBOF interrupt will be generated
#1 : 1
RBOF interrupt will be generated
End of enumeration elements list.
RESERVED : no description available
bits : 18 - 20 (3 bit)
access : read-only
RBDDE : no description available
bits : 21 - 21 (1 bit)
access : read-write
Enumeration:
#0 : 0
No DMA request will be generated
#1 : 1
DMA request will be generated
End of enumeration elements list.
RESERVED : no description available
bits : 22 - 22 (1 bit)
access : read-only
ILLINIE : no description available
bits : 23 - 23 (1 bit)
access : read-write
Enumeration:
#0 : 0
No ILLINE interrupt will be generated
#1 : 1
ILLINE interrupt will be generated
End of enumeration elements list.
RESERVED : no description available
bits : 24 - 25 (2 bit)
access : read-only
TBUIE : no description available
bits : 26 - 26 (1 bit)
access : read-write
Enumeration:
#0 : 0
No TBUF interrupt will be generated
#1 : 1
TBUF interrupt will be generated
End of enumeration elements list.
TBFIE : no description available
bits : 27 - 27 (1 bit)
access : read-write
Enumeration:
#0 : 0
No TBFF interrupt will be generated
#1 : 1
TBFF interrupt will be generated
End of enumeration elements list.
RESERVED : no description available
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : no description available
bits : 29 - 30 (2 bit)
access : read-only
DLPFIE : no description available
bits : 31 - 31 (1 bit)
access : read-write
Enumeration:
#0 : 0
No DLPFF interrupt will be generated
#1 : 1
DLPFF interrupt will be generated
End of enumeration elements list.
Sequence Suspend Status Register
address_offset : 0x168 Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
SUSPND : no description available
bits : 0 - 0 (1 bit)
access : read-only
RESERVED : no description available
bits : 1 - 5 (5 bit)
access : read-only
SPDBUF : no description available
bits : 6 - 7 (2 bit)
access : read-only
RESERVED : no description available
bits : 8 - 8 (1 bit)
access : read-only
DATLFT : no description available
bits : 9 - 15 (7 bit)
access : read-only
RESERVED : no description available
bits : 16 - 31 (16 bit)
access : read-only
RX Buffer Data Register
address_offset : 0x16B4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RXDATA : no description available
bits : 0 - 31 (32 bit)
access : read-write
Sequence Pointer Clear Register
address_offset : 0x16C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
BFPTRC : no description available
bits : 0 - 0 (1 bit)
access : read-write
RESERVED : no description available
bits : 1 - 7 (7 bit)
access : read-only
IPPTRC : no description available
bits : 8 - 8 (1 bit)
access : read-write
RESERVED : no description available
bits : 9 - 31 (23 bit)
access : read-only
Buffer2 Configuration Register
address_offset : 0x18 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MSTRID : no description available
bits : 0 - 3 (4 bit)
access : read-write
RESERVED : no description available
bits : 4 - 7 (4 bit)
access : read-only
ADATSZ : no description available
bits : 8 - 15 (8 bit)
access : read-write
RESERVED : no description available
bits : 16 - 31 (16 bit)
access : read-only
Serial Flash A1 Top Address
address_offset : 0x180 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RESERVED : no description available
bits : 0 - 9 (10 bit)
access : read-only
TPADA1 : no description available
bits : 10 - 31 (22 bit)
access : read-write
Serial Flash A2 Top Address
address_offset : 0x184 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RESERVED : no description available
bits : 0 - 9 (10 bit)
access : read-only
TPADA2 : no description available
bits : 10 - 31 (22 bit)
access : read-write
Serial Flash B1Top Address
address_offset : 0x188 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RESERVED : no description available
bits : 0 - 9 (10 bit)
access : read-only
TPADB1 : no description available
bits : 10 - 31 (22 bit)
access : read-write
Serial Flash B2Top Address
address_offset : 0x18C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RESERVED : no description available
bits : 0 - 9 (10 bit)
access : read-only
TPADB2 : no description available
bits : 10 - 31 (22 bit)
access : read-write
RX Buffer Data Register
address_offset : 0x18DC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RXDATA : no description available
bits : 0 - 31 (32 bit)
access : read-write
Look-up Table register
address_offset : 0x1914 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OPRND0 : Operand for INSTR0.
bits : 0 - 7 (8 bit)
access : read-write
PAD0 : Pad information for INSTR0.
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR0 : Instruction 0
bits : 10 - 15 (6 bit)
access : read-write
OPRND1 : Operand for INSTR1.
bits : 16 - 23 (8 bit)
access : read-write
PAD1 : Pad information for INSTR1.
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR1 : Instruction 1
bits : 26 - 31 (6 bit)
access : read-write
RX Buffer Data Register
address_offset : 0x1B08 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RXDATA : no description available
bits : 0 - 31 (32 bit)
access : read-write
Buffer3 Configuration Register
address_offset : 0x1C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MSTRID : no description available
bits : 0 - 3 (4 bit)
access : read-write
RESERVED : no description available
bits : 4 - 7 (4 bit)
access : read-only
ADATSZ : no description available
bits : 8 - 15 (8 bit)
access : read-write
RESERVED : no description available
bits : 16 - 30 (15 bit)
access : read-only
ALLMST : no description available
bits : 31 - 31 (1 bit)
access : read-write
Look-up Table register
address_offset : 0x1C48 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OPRND0 : Operand for INSTR0.
bits : 0 - 7 (8 bit)
access : read-write
PAD0 : Pad information for INSTR0.
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR0 : Instruction 0
bits : 10 - 15 (6 bit)
access : read-write
OPRND1 : Operand for INSTR1.
bits : 16 - 23 (8 bit)
access : read-write
PAD1 : Pad information for INSTR1.
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR1 : Instruction 1
bits : 26 - 31 (6 bit)
access : read-write
RX Buffer Data Register
address_offset : 0x1D38 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RXDATA : no description available
bits : 0 - 31 (32 bit)
access : read-write
RX Buffer Data Register
address_offset : 0x1F6C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RXDATA : no description available
bits : 0 - 31 (32 bit)
access : read-write
Look-up Table register
address_offset : 0x1F80 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OPRND0 : Operand for INSTR0.
bits : 0 - 7 (8 bit)
access : read-write
PAD0 : Pad information for INSTR0.
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR0 : Instruction 0
bits : 10 - 15 (6 bit)
access : read-write
OPRND1 : Operand for INSTR1.
bits : 16 - 23 (8 bit)
access : read-write
PAD1 : Pad information for INSTR1.
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR1 : Instruction 1
bits : 26 - 31 (6 bit)
access : read-write
Buffer Generic Configuration Register
address_offset : 0x20 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RESERVED : no description available
bits : 0 - 11 (12 bit)
access : read-only
SEQID : no description available
bits : 12 - 15 (4 bit)
access : read-write
PAR_EN : no description available
bits : 16 - 16 (1 bit)
access : read-write
RESERVED : no description available
bits : 17 - 31 (15 bit)
access : read-only
RX Buffer Data Register
address_offset : 0x21A4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RXDATA : no description available
bits : 0 - 31 (32 bit)
access : read-write
Look-up Table register
address_offset : 0x22BC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OPRND0 : Operand for INSTR0.
bits : 0 - 7 (8 bit)
access : read-write
PAD0 : Pad information for INSTR0.
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR0 : Instruction 0
bits : 10 - 15 (6 bit)
access : read-write
OPRND1 : Operand for INSTR1.
bits : 16 - 23 (8 bit)
access : read-write
PAD1 : Pad information for INSTR1.
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR1 : Instruction 1
bits : 26 - 31 (6 bit)
access : read-write
RX Buffer Data Register
address_offset : 0x23E0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RXDATA : no description available
bits : 0 - 31 (32 bit)
access : read-write
Look-up Table register
address_offset : 0x25FC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OPRND0 : Operand for INSTR0.
bits : 0 - 7 (8 bit)
access : read-write
PAD0 : Pad information for INSTR0.
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR0 : Instruction 0
bits : 10 - 15 (6 bit)
access : read-write
OPRND1 : Operand for INSTR1.
bits : 16 - 23 (8 bit)
access : read-write
PAD1 : Pad information for INSTR1.
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR1 : Instruction 1
bits : 26 - 31 (6 bit)
access : read-write
RX Buffer Data Register
address_offset : 0x2620 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RXDATA : no description available
bits : 0 - 31 (32 bit)
access : read-write
RX Buffer Data Register
address_offset : 0x2864 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RXDATA : no description available
bits : 0 - 31 (32 bit)
access : read-write
Look-up Table register
address_offset : 0x2940 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OPRND0 : Operand for INSTR0.
bits : 0 - 7 (8 bit)
access : read-write
PAD0 : Pad information for INSTR0.
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR0 : Instruction 0
bits : 10 - 15 (6 bit)
access : read-write
OPRND1 : Operand for INSTR1.
bits : 16 - 23 (8 bit)
access : read-write
PAD1 : Pad information for INSTR1.
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR1 : Instruction 1
bits : 26 - 31 (6 bit)
access : read-write
RX Buffer Data Register
address_offset : 0x2AAC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RXDATA : no description available
bits : 0 - 31 (32 bit)
access : read-write
Look-up Table register
address_offset : 0x2C88 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OPRND0 : Operand for INSTR0.
bits : 0 - 7 (8 bit)
access : read-write
PAD0 : Pad information for INSTR0.
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR0 : Instruction 0
bits : 10 - 15 (6 bit)
access : read-write
OPRND1 : Operand for INSTR1.
bits : 16 - 23 (8 bit)
access : read-write
PAD1 : Pad information for INSTR1.
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR1 : Instruction 1
bits : 26 - 31 (6 bit)
access : read-write
RX Buffer Data Register
address_offset : 0x2CF8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RXDATA : no description available
bits : 0 - 31 (32 bit)
access : read-write
RX Buffer Data Register
address_offset : 0x2F48 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RXDATA : no description available
bits : 0 - 31 (32 bit)
access : read-write
Look-up Table register
address_offset : 0x2FD4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OPRND0 : Operand for INSTR0.
bits : 0 - 7 (8 bit)
access : read-write
PAD0 : Pad information for INSTR0.
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR0 : Instruction 0
bits : 10 - 15 (6 bit)
access : read-write
OPRND1 : Operand for INSTR1.
bits : 16 - 23 (8 bit)
access : read-write
PAD1 : Pad information for INSTR1.
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR1 : Instruction 1
bits : 26 - 31 (6 bit)
access : read-write
Buffer0 Top Index Register
address_offset : 0x30 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RESERVED : no description available
bits : 0 - 2 (3 bit)
access : read-only
TPINDX0 : no description available
bits : 3 - 31 (29 bit)
access : read-write
LUT Key Register
address_offset : 0x300 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
KEY : no description available
bits : 0 - 31 (32 bit)
access : read-write
LUT Lock Configuration Register
address_offset : 0x304 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
LOCK : no description available
bits : 0 - 0 (1 bit)
access : read-write
UNLOCK : no description available
bits : 1 - 1 (1 bit)
access : read-write
RESERVED : no description available
bits : 2 - 31 (30 bit)
access : read-only
Look-up Table register
address_offset : 0x310 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OPRND0 : Operand for INSTR0.
bits : 0 - 7 (8 bit)
access : read-write
PAD0 : Pad information for INSTR0.
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR0 : Instruction 0
bits : 10 - 15 (6 bit)
access : read-write
OPRND1 : Operand for INSTR1.
bits : 16 - 23 (8 bit)
access : read-write
PAD1 : Pad information for INSTR1.
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR1 : Instruction 1
bits : 26 - 31 (6 bit)
access : read-write
Look-up Table register
address_offset : 0x314 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OPRND0 : Operand for INSTR0.
bits : 0 - 7 (8 bit)
access : read-write
PAD0 : Pad information for INSTR0.
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR0 : Instruction 0
bits : 10 - 15 (6 bit)
access : read-write
OPRND1 : Operand for INSTR1.
bits : 16 - 23 (8 bit)
access : read-write
PAD1 : Pad information for INSTR1.
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR1 : Instruction 1
bits : 26 - 31 (6 bit)
access : read-write
RX Buffer Data Register
address_offset : 0x319C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RXDATA : no description available
bits : 0 - 31 (32 bit)
access : read-write
Look-up Table register
address_offset : 0x3324 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OPRND0 : Operand for INSTR0.
bits : 0 - 7 (8 bit)
access : read-write
PAD0 : Pad information for INSTR0.
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR0 : Instruction 0
bits : 10 - 15 (6 bit)
access : read-write
OPRND1 : Operand for INSTR1.
bits : 16 - 23 (8 bit)
access : read-write
PAD1 : Pad information for INSTR1.
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR1 : Instruction 1
bits : 26 - 31 (6 bit)
access : read-write
RX Buffer Data Register
address_offset : 0x33F4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RXDATA : no description available
bits : 0 - 31 (32 bit)
access : read-write
Buffer1 Top Index Register
address_offset : 0x34 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RESERVED : no description available
bits : 0 - 2 (3 bit)
access : read-only
TPINDX1 : no description available
bits : 3 - 31 (29 bit)
access : read-write
RX Buffer Data Register
address_offset : 0x3650 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RXDATA : no description available
bits : 0 - 31 (32 bit)
access : read-write
Look-up Table register
address_offset : 0x3678 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OPRND0 : Operand for INSTR0.
bits : 0 - 7 (8 bit)
access : read-write
PAD0 : Pad information for INSTR0.
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR0 : Instruction 0
bits : 10 - 15 (6 bit)
access : read-write
OPRND1 : Operand for INSTR1.
bits : 16 - 23 (8 bit)
access : read-write
PAD1 : Pad information for INSTR1.
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR1 : Instruction 1
bits : 26 - 31 (6 bit)
access : read-write
Buffer2 Top Index Register
address_offset : 0x38 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RESERVED : no description available
bits : 0 - 2 (3 bit)
access : read-only
TPINDX2 : no description available
bits : 3 - 31 (29 bit)
access : read-write
RX Buffer Data Register
address_offset : 0x38B0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RXDATA : no description available
bits : 0 - 31 (32 bit)
access : read-write
Look-up Table register
address_offset : 0x39D0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OPRND0 : Operand for INSTR0.
bits : 0 - 7 (8 bit)
access : read-write
PAD0 : Pad information for INSTR0.
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR0 : Instruction 0
bits : 10 - 15 (6 bit)
access : read-write
OPRND1 : Operand for INSTR1.
bits : 16 - 23 (8 bit)
access : read-write
PAD1 : Pad information for INSTR1.
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR1 : Instruction 1
bits : 26 - 31 (6 bit)
access : read-write
RX Buffer Data Register
address_offset : 0x3B14 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RXDATA : no description available
bits : 0 - 31 (32 bit)
access : read-write
Look-up Table register
address_offset : 0x3D2C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OPRND0 : Operand for INSTR0.
bits : 0 - 7 (8 bit)
access : read-write
PAD0 : Pad information for INSTR0.
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR0 : Instruction 0
bits : 10 - 15 (6 bit)
access : read-write
OPRND1 : Operand for INSTR1.
bits : 16 - 23 (8 bit)
access : read-write
PAD1 : Pad information for INSTR1.
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR1 : Instruction 1
bits : 26 - 31 (6 bit)
access : read-write
RX Buffer Data Register
address_offset : 0x3D7C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RXDATA : no description available
bits : 0 - 31 (32 bit)
access : read-write
RX Buffer Data Register
address_offset : 0x3FE8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RXDATA : no description available
bits : 0 - 31 (32 bit)
access : read-write
RX Buffer Data Register
address_offset : 0x400 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RXDATA : no description available
bits : 0 - 31 (32 bit)
access : read-write
Look-up Table register
address_offset : 0x408C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OPRND0 : Operand for INSTR0.
bits : 0 - 7 (8 bit)
access : read-write
PAD0 : Pad information for INSTR0.
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR0 : Instruction 0
bits : 10 - 15 (6 bit)
access : read-write
OPRND1 : Operand for INSTR1.
bits : 16 - 23 (8 bit)
access : read-write
PAD1 : Pad information for INSTR1.
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR1 : Instruction 1
bits : 26 - 31 (6 bit)
access : read-write
RX Buffer Data Register
address_offset : 0x4258 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RXDATA : no description available
bits : 0 - 31 (32 bit)
access : read-write
Look-up Table register
address_offset : 0x43F0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OPRND0 : Operand for INSTR0.
bits : 0 - 7 (8 bit)
access : read-write
PAD0 : Pad information for INSTR0.
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR0 : Instruction 0
bits : 10 - 15 (6 bit)
access : read-write
OPRND1 : Operand for INSTR1.
bits : 16 - 23 (8 bit)
access : read-write
PAD1 : Pad information for INSTR1.
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR1 : Instruction 1
bits : 26 - 31 (6 bit)
access : read-write
RX Buffer Data Register
address_offset : 0x44CC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RXDATA : no description available
bits : 0 - 31 (32 bit)
access : read-write
RX Buffer Data Register
address_offset : 0x4744 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RXDATA : no description available
bits : 0 - 31 (32 bit)
access : read-write
Look-up Table register
address_offset : 0x4758 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OPRND0 : Operand for INSTR0.
bits : 0 - 7 (8 bit)
access : read-write
PAD0 : Pad information for INSTR0.
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR0 : Instruction 0
bits : 10 - 15 (6 bit)
access : read-write
OPRND1 : Operand for INSTR1.
bits : 16 - 23 (8 bit)
access : read-write
PAD1 : Pad information for INSTR1.
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR1 : Instruction 1
bits : 26 - 31 (6 bit)
access : read-write
RX Buffer Data Register
address_offset : 0x49C0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RXDATA : no description available
bits : 0 - 31 (32 bit)
access : read-write
Look-up Table register
address_offset : 0x4AC4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OPRND0 : Operand for INSTR0.
bits : 0 - 7 (8 bit)
access : read-write
PAD0 : Pad information for INSTR0.
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR0 : Instruction 0
bits : 10 - 15 (6 bit)
access : read-write
OPRND1 : Operand for INSTR1.
bits : 16 - 23 (8 bit)
access : read-write
PAD1 : Pad information for INSTR1.
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR1 : Instruction 1
bits : 26 - 31 (6 bit)
access : read-write
Look-up Table register
address_offset : 0x4E34 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OPRND0 : Operand for INSTR0.
bits : 0 - 7 (8 bit)
access : read-write
PAD0 : Pad information for INSTR0.
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR0 : Instruction 0
bits : 10 - 15 (6 bit)
access : read-write
OPRND1 : Operand for INSTR1.
bits : 16 - 23 (8 bit)
access : read-write
PAD1 : Pad information for INSTR1.
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR1 : Instruction 1
bits : 26 - 31 (6 bit)
access : read-write
Look-up Table register
address_offset : 0x51A8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OPRND0 : Operand for INSTR0.
bits : 0 - 7 (8 bit)
access : read-write
PAD0 : Pad information for INSTR0.
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR0 : Instruction 0
bits : 10 - 15 (6 bit)
access : read-write
OPRND1 : Operand for INSTR1.
bits : 16 - 23 (8 bit)
access : read-write
PAD1 : Pad information for INSTR1.
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR1 : Instruction 1
bits : 26 - 31 (6 bit)
access : read-write
Look-up Table register
address_offset : 0x5520 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OPRND0 : Operand for INSTR0.
bits : 0 - 7 (8 bit)
access : read-write
PAD0 : Pad information for INSTR0.
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR0 : Instruction 0
bits : 10 - 15 (6 bit)
access : read-write
OPRND1 : Operand for INSTR1.
bits : 16 - 23 (8 bit)
access : read-write
PAD1 : Pad information for INSTR1.
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR1 : Instruction 1
bits : 26 - 31 (6 bit)
access : read-write
Look-up Table register
address_offset : 0x589C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OPRND0 : Operand for INSTR0.
bits : 0 - 7 (8 bit)
access : read-write
PAD0 : Pad information for INSTR0.
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR0 : Instruction 0
bits : 10 - 15 (6 bit)
access : read-write
OPRND1 : Operand for INSTR1.
bits : 16 - 23 (8 bit)
access : read-write
PAD1 : Pad information for INSTR1.
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR1 : Instruction 1
bits : 26 - 31 (6 bit)
access : read-write
Look-up Table register
address_offset : 0x5C1C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OPRND0 : Operand for INSTR0.
bits : 0 - 7 (8 bit)
access : read-write
PAD0 : Pad information for INSTR0.
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR0 : Instruction 0
bits : 10 - 15 (6 bit)
access : read-write
OPRND1 : Operand for INSTR1.
bits : 16 - 23 (8 bit)
access : read-write
PAD1 : Pad information for INSTR1.
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR1 : Instruction 1
bits : 26 - 31 (6 bit)
access : read-write
Look-up Table register
address_offset : 0x5FA0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OPRND0 : Operand for INSTR0.
bits : 0 - 7 (8 bit)
access : read-write
PAD0 : Pad information for INSTR0.
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR0 : Instruction 0
bits : 10 - 15 (6 bit)
access : read-write
OPRND1 : Operand for INSTR1.
bits : 16 - 23 (8 bit)
access : read-write
PAD1 : Pad information for INSTR1.
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR1 : Instruction 1
bits : 26 - 31 (6 bit)
access : read-write
RX Buffer Data Register
address_offset : 0x604 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RXDATA : no description available
bits : 0 - 31 (32 bit)
access : read-write
Look-up Table register
address_offset : 0x630 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OPRND0 : Operand for INSTR0.
bits : 0 - 7 (8 bit)
access : read-write
PAD0 : Pad information for INSTR0.
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR0 : Instruction 0
bits : 10 - 15 (6 bit)
access : read-write
OPRND1 : Operand for INSTR1.
bits : 16 - 23 (8 bit)
access : read-write
PAD1 : Pad information for INSTR1.
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR1 : Instruction 1
bits : 26 - 31 (6 bit)
access : read-write
Look-up Table register
address_offset : 0x6328 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OPRND0 : Operand for INSTR0.
bits : 0 - 7 (8 bit)
access : read-write
PAD0 : Pad information for INSTR0.
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR0 : Instruction 0
bits : 10 - 15 (6 bit)
access : read-write
OPRND1 : Operand for INSTR1.
bits : 16 - 23 (8 bit)
access : read-write
PAD1 : Pad information for INSTR1.
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR1 : Instruction 1
bits : 26 - 31 (6 bit)
access : read-write
Look-up Table register
address_offset : 0x66B4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OPRND0 : Operand for INSTR0.
bits : 0 - 7 (8 bit)
access : read-write
PAD0 : Pad information for INSTR0.
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR0 : Instruction 0
bits : 10 - 15 (6 bit)
access : read-write
OPRND1 : Operand for INSTR1.
bits : 16 - 23 (8 bit)
access : read-write
PAD1 : Pad information for INSTR1.
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR1 : Instruction 1
bits : 26 - 31 (6 bit)
access : read-write
Look-up Table register
address_offset : 0x6A44 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OPRND0 : Operand for INSTR0.
bits : 0 - 7 (8 bit)
access : read-write
PAD0 : Pad information for INSTR0.
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR0 : Instruction 0
bits : 10 - 15 (6 bit)
access : read-write
OPRND1 : Operand for INSTR1.
bits : 16 - 23 (8 bit)
access : read-write
PAD1 : Pad information for INSTR1.
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR1 : Instruction 1
bits : 26 - 31 (6 bit)
access : read-write
Look-up Table register
address_offset : 0x6DD8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OPRND0 : Operand for INSTR0.
bits : 0 - 7 (8 bit)
access : read-write
PAD0 : Pad information for INSTR0.
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR0 : Instruction 0
bits : 10 - 15 (6 bit)
access : read-write
OPRND1 : Operand for INSTR1.
bits : 16 - 23 (8 bit)
access : read-write
PAD1 : Pad information for INSTR1.
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR1 : Instruction 1
bits : 26 - 31 (6 bit)
access : read-write
Look-up Table register
address_offset : 0x7170 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OPRND0 : Operand for INSTR0.
bits : 0 - 7 (8 bit)
access : read-write
PAD0 : Pad information for INSTR0.
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR0 : Instruction 0
bits : 10 - 15 (6 bit)
access : read-write
OPRND1 : Operand for INSTR1.
bits : 16 - 23 (8 bit)
access : read-write
PAD1 : Pad information for INSTR1.
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR1 : Instruction 1
bits : 26 - 31 (6 bit)
access : read-write
Look-up Table register
address_offset : 0x750C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OPRND0 : Operand for INSTR0.
bits : 0 - 7 (8 bit)
access : read-write
PAD0 : Pad information for INSTR0.
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR0 : Instruction 0
bits : 10 - 15 (6 bit)
access : read-write
OPRND1 : Operand for INSTR1.
bits : 16 - 23 (8 bit)
access : read-write
PAD1 : Pad information for INSTR1.
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR1 : Instruction 1
bits : 26 - 31 (6 bit)
access : read-write
Look-up Table register
address_offset : 0x78AC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OPRND0 : Operand for INSTR0.
bits : 0 - 7 (8 bit)
access : read-write
PAD0 : Pad information for INSTR0.
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR0 : Instruction 0
bits : 10 - 15 (6 bit)
access : read-write
OPRND1 : Operand for INSTR1.
bits : 16 - 23 (8 bit)
access : read-write
PAD1 : Pad information for INSTR1.
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR1 : Instruction 1
bits : 26 - 31 (6 bit)
access : read-write
Look-up Table register
address_offset : 0x7C50 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OPRND0 : Operand for INSTR0.
bits : 0 - 7 (8 bit)
access : read-write
PAD0 : Pad information for INSTR0.
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR0 : Instruction 0
bits : 10 - 15 (6 bit)
access : read-write
OPRND1 : Operand for INSTR1.
bits : 16 - 23 (8 bit)
access : read-write
PAD1 : Pad information for INSTR1.
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR1 : Instruction 1
bits : 26 - 31 (6 bit)
access : read-write
Look-up Table register
address_offset : 0x7FF8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OPRND0 : Operand for INSTR0.
bits : 0 - 7 (8 bit)
access : read-write
PAD0 : Pad information for INSTR0.
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR0 : Instruction 0
bits : 10 - 15 (6 bit)
access : read-write
OPRND1 : Operand for INSTR1.
bits : 16 - 23 (8 bit)
access : read-write
PAD1 : Pad information for INSTR1.
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR1 : Instruction 1
bits : 26 - 31 (6 bit)
access : read-write
IP Configuration Register
address_offset : 0x8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
IDATSZ : no description available
bits : 0 - 15 (16 bit)
access : read-write
PAR_EN : no description available
bits : 16 - 16 (1 bit)
access : read-write
RESERVED : no description available
bits : 17 - 23 (7 bit)
access : read-only
SEQID : no description available
bits : 24 - 27 (4 bit)
access : read-write
RESERVED : no description available
bits : 28 - 31 (4 bit)
access : read-only
RX Buffer Data Register
address_offset : 0x80C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RXDATA : no description available
bits : 0 - 31 (32 bit)
access : read-write
Look-up Table register
address_offset : 0x83A4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OPRND0 : Operand for INSTR0.
bits : 0 - 7 (8 bit)
access : read-write
PAD0 : Pad information for INSTR0.
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR0 : Instruction 0
bits : 10 - 15 (6 bit)
access : read-write
OPRND1 : Operand for INSTR1.
bits : 16 - 23 (8 bit)
access : read-write
PAD1 : Pad information for INSTR1.
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR1 : Instruction 1
bits : 26 - 31 (6 bit)
access : read-write
Look-up Table register
address_offset : 0x8754 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OPRND0 : Operand for INSTR0.
bits : 0 - 7 (8 bit)
access : read-write
PAD0 : Pad information for INSTR0.
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR0 : Instruction 0
bits : 10 - 15 (6 bit)
access : read-write
OPRND1 : Operand for INSTR1.
bits : 16 - 23 (8 bit)
access : read-write
PAD1 : Pad information for INSTR1.
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR1 : Instruction 1
bits : 26 - 31 (6 bit)
access : read-write
Look-up Table register
address_offset : 0x8B08 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OPRND0 : Operand for INSTR0.
bits : 0 - 7 (8 bit)
access : read-write
PAD0 : Pad information for INSTR0.
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR0 : Instruction 0
bits : 10 - 15 (6 bit)
access : read-write
OPRND1 : Operand for INSTR1.
bits : 16 - 23 (8 bit)
access : read-write
PAD1 : Pad information for INSTR1.
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR1 : Instruction 1
bits : 26 - 31 (6 bit)
access : read-write
Look-up Table register
address_offset : 0x8EC0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OPRND0 : Operand for INSTR0.
bits : 0 - 7 (8 bit)
access : read-write
PAD0 : Pad information for INSTR0.
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR0 : Instruction 0
bits : 10 - 15 (6 bit)
access : read-write
OPRND1 : Operand for INSTR1.
bits : 16 - 23 (8 bit)
access : read-write
PAD1 : Pad information for INSTR1.
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR1 : Instruction 1
bits : 26 - 31 (6 bit)
access : read-write
Look-up Table register
address_offset : 0x927C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OPRND0 : Operand for INSTR0.
bits : 0 - 7 (8 bit)
access : read-write
PAD0 : Pad information for INSTR0.
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR0 : Instruction 0
bits : 10 - 15 (6 bit)
access : read-write
OPRND1 : Operand for INSTR1.
bits : 16 - 23 (8 bit)
access : read-write
PAD1 : Pad information for INSTR1.
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR1 : Instruction 1
bits : 26 - 31 (6 bit)
access : read-write
Look-up Table register
address_offset : 0x94C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OPRND0 : Operand for INSTR0.
bits : 0 - 7 (8 bit)
access : read-write
PAD0 : Pad information for INSTR0.
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR0 : Instruction 0
bits : 10 - 15 (6 bit)
access : read-write
OPRND1 : Operand for INSTR1.
bits : 16 - 23 (8 bit)
access : read-write
PAD1 : Pad information for INSTR1.
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR1 : Instruction 1
bits : 26 - 31 (6 bit)
access : read-write
Look-up Table register
address_offset : 0x963C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OPRND0 : Operand for INSTR0.
bits : 0 - 7 (8 bit)
access : read-write
PAD0 : Pad information for INSTR0.
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR0 : Instruction 0
bits : 10 - 15 (6 bit)
access : read-write
OPRND1 : Operand for INSTR1.
bits : 16 - 23 (8 bit)
access : read-write
PAD1 : Pad information for INSTR1.
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR1 : Instruction 1
bits : 26 - 31 (6 bit)
access : read-write
Look-up Table register
address_offset : 0x9A00 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OPRND0 : Operand for INSTR0.
bits : 0 - 7 (8 bit)
access : read-write
PAD0 : Pad information for INSTR0.
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR0 : Instruction 0
bits : 10 - 15 (6 bit)
access : read-write
OPRND1 : Operand for INSTR1.
bits : 16 - 23 (8 bit)
access : read-write
PAD1 : Pad information for INSTR1.
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR1 : Instruction 1
bits : 26 - 31 (6 bit)
access : read-write
Look-up Table register
address_offset : 0x9DC8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OPRND0 : Operand for INSTR0.
bits : 0 - 7 (8 bit)
access : read-write
PAD0 : Pad information for INSTR0.
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR0 : Instruction 0
bits : 10 - 15 (6 bit)
access : read-write
OPRND1 : Operand for INSTR1.
bits : 16 - 23 (8 bit)
access : read-write
PAD1 : Pad information for INSTR1.
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR1 : Instruction 1
bits : 26 - 31 (6 bit)
access : read-write
RX Buffer Data Register
address_offset : 0xA18 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RXDATA : no description available
bits : 0 - 31 (32 bit)
access : read-write
Look-up Table register
address_offset : 0xA194 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OPRND0 : Operand for INSTR0.
bits : 0 - 7 (8 bit)
access : read-write
PAD0 : Pad information for INSTR0.
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR0 : Instruction 0
bits : 10 - 15 (6 bit)
access : read-write
OPRND1 : Operand for INSTR1.
bits : 16 - 23 (8 bit)
access : read-write
PAD1 : Pad information for INSTR1.
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR1 : Instruction 1
bits : 26 - 31 (6 bit)
access : read-write
Look-up Table register
address_offset : 0xA564 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OPRND0 : Operand for INSTR0.
bits : 0 - 7 (8 bit)
access : read-write
PAD0 : Pad information for INSTR0.
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR0 : Instruction 0
bits : 10 - 15 (6 bit)
access : read-write
OPRND1 : Operand for INSTR1.
bits : 16 - 23 (8 bit)
access : read-write
PAD1 : Pad information for INSTR1.
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR1 : Instruction 1
bits : 26 - 31 (6 bit)
access : read-write
Look-up Table register
address_offset : 0xA938 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OPRND0 : Operand for INSTR0.
bits : 0 - 7 (8 bit)
access : read-write
PAD0 : Pad information for INSTR0.
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR0 : Instruction 0
bits : 10 - 15 (6 bit)
access : read-write
OPRND1 : Operand for INSTR1.
bits : 16 - 23 (8 bit)
access : read-write
PAD1 : Pad information for INSTR1.
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR1 : Instruction 1
bits : 26 - 31 (6 bit)
access : read-write
Look-up Table register
address_offset : 0xAD10 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OPRND0 : Operand for INSTR0.
bits : 0 - 7 (8 bit)
access : read-write
PAD0 : Pad information for INSTR0.
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR0 : Instruction 0
bits : 10 - 15 (6 bit)
access : read-write
OPRND1 : Operand for INSTR1.
bits : 16 - 23 (8 bit)
access : read-write
PAD1 : Pad information for INSTR1.
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR1 : Instruction 1
bits : 26 - 31 (6 bit)
access : read-write
Look-up Table register
address_offset : 0xB0EC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OPRND0 : Operand for INSTR0.
bits : 0 - 7 (8 bit)
access : read-write
PAD0 : Pad information for INSTR0.
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR0 : Instruction 0
bits : 10 - 15 (6 bit)
access : read-write
OPRND1 : Operand for INSTR1.
bits : 16 - 23 (8 bit)
access : read-write
PAD1 : Pad information for INSTR1.
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR1 : Instruction 1
bits : 26 - 31 (6 bit)
access : read-write
Look-up Table register
address_offset : 0xB4CC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OPRND0 : Operand for INSTR0.
bits : 0 - 7 (8 bit)
access : read-write
PAD0 : Pad information for INSTR0.
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR0 : Instruction 0
bits : 10 - 15 (6 bit)
access : read-write
OPRND1 : Operand for INSTR1.
bits : 16 - 23 (8 bit)
access : read-write
PAD1 : Pad information for INSTR1.
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR1 : Instruction 1
bits : 26 - 31 (6 bit)
access : read-write
Look-up Table register
address_offset : 0xB8B0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OPRND0 : Operand for INSTR0.
bits : 0 - 7 (8 bit)
access : read-write
PAD0 : Pad information for INSTR0.
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR0 : Instruction 0
bits : 10 - 15 (6 bit)
access : read-write
OPRND1 : Operand for INSTR1.
bits : 16 - 23 (8 bit)
access : read-write
PAD1 : Pad information for INSTR1.
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR1 : Instruction 1
bits : 26 - 31 (6 bit)
access : read-write
Look-up Table register
address_offset : 0xBC98 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OPRND0 : Operand for INSTR0.
bits : 0 - 7 (8 bit)
access : read-write
PAD0 : Pad information for INSTR0.
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR0 : Instruction 0
bits : 10 - 15 (6 bit)
access : read-write
OPRND1 : Operand for INSTR1.
bits : 16 - 23 (8 bit)
access : read-write
PAD1 : Pad information for INSTR1.
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR1 : Instruction 1
bits : 26 - 31 (6 bit)
access : read-write
Flash Configuration Register
address_offset : 0xC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TCSS : no description available
bits : 0 - 3 (4 bit)
access : read-write
RESERVED : no description available
bits : 4 - 7 (4 bit)
access : read-only
TCSH : no description available
bits : 8 - 11 (4 bit)
access : read-write
RESERVED : no description available
bits : 12 - 31 (20 bit)
access : read-only
Look-up Table register
address_offset : 0xC084 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OPRND0 : Operand for INSTR0.
bits : 0 - 7 (8 bit)
access : read-write
PAD0 : Pad information for INSTR0.
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR0 : Instruction 0
bits : 10 - 15 (6 bit)
access : read-write
OPRND1 : Operand for INSTR1.
bits : 16 - 23 (8 bit)
access : read-write
PAD1 : Pad information for INSTR1.
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR1 : Instruction 1
bits : 26 - 31 (6 bit)
access : read-write
RX Buffer Data Register
address_offset : 0xC28 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RXDATA : no description available
bits : 0 - 31 (32 bit)
access : read-write
Look-up Table register
address_offset : 0xC474 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OPRND0 : Operand for INSTR0.
bits : 0 - 7 (8 bit)
access : read-write
PAD0 : Pad information for INSTR0.
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR0 : Instruction 0
bits : 10 - 15 (6 bit)
access : read-write
OPRND1 : Operand for INSTR1.
bits : 16 - 23 (8 bit)
access : read-write
PAD1 : Pad information for INSTR1.
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR1 : Instruction 1
bits : 26 - 31 (6 bit)
access : read-write
Look-up Table register
address_offset : 0xC6C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OPRND0 : Operand for INSTR0.
bits : 0 - 7 (8 bit)
access : read-write
PAD0 : Pad information for INSTR0.
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR0 : Instruction 0
bits : 10 - 15 (6 bit)
access : read-write
OPRND1 : Operand for INSTR1.
bits : 16 - 23 (8 bit)
access : read-write
PAD1 : Pad information for INSTR1.
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR1 : Instruction 1
bits : 26 - 31 (6 bit)
access : read-write
Look-up Table register
address_offset : 0xC868 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OPRND0 : Operand for INSTR0.
bits : 0 - 7 (8 bit)
access : read-write
PAD0 : Pad information for INSTR0.
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR0 : Instruction 0
bits : 10 - 15 (6 bit)
access : read-write
OPRND1 : Operand for INSTR1.
bits : 16 - 23 (8 bit)
access : read-write
PAD1 : Pad information for INSTR1.
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR1 : Instruction 1
bits : 26 - 31 (6 bit)
access : read-write
Look-up Table register
address_offset : 0xCC60 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OPRND0 : Operand for INSTR0.
bits : 0 - 7 (8 bit)
access : read-write
PAD0 : Pad information for INSTR0.
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR0 : Instruction 0
bits : 10 - 15 (6 bit)
access : read-write
OPRND1 : Operand for INSTR1.
bits : 16 - 23 (8 bit)
access : read-write
PAD1 : Pad information for INSTR1.
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR1 : Instruction 1
bits : 26 - 31 (6 bit)
access : read-write
Look-up Table register
address_offset : 0xD05C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OPRND0 : Operand for INSTR0.
bits : 0 - 7 (8 bit)
access : read-write
PAD0 : Pad information for INSTR0.
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR0 : Instruction 0
bits : 10 - 15 (6 bit)
access : read-write
OPRND1 : Operand for INSTR1.
bits : 16 - 23 (8 bit)
access : read-write
PAD1 : Pad information for INSTR1.
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR1 : Instruction 1
bits : 26 - 31 (6 bit)
access : read-write
Look-up Table register
address_offset : 0xD45C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OPRND0 : Operand for INSTR0.
bits : 0 - 7 (8 bit)
access : read-write
PAD0 : Pad information for INSTR0.
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR0 : Instruction 0
bits : 10 - 15 (6 bit)
access : read-write
OPRND1 : Operand for INSTR1.
bits : 16 - 23 (8 bit)
access : read-write
PAD1 : Pad information for INSTR1.
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR1 : Instruction 1
bits : 26 - 31 (6 bit)
access : read-write
Look-up Table register
address_offset : 0xD860 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OPRND0 : Operand for INSTR0.
bits : 0 - 7 (8 bit)
access : read-write
PAD0 : Pad information for INSTR0.
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR0 : Instruction 0
bits : 10 - 15 (6 bit)
access : read-write
OPRND1 : Operand for INSTR1.
bits : 16 - 23 (8 bit)
access : read-write
PAD1 : Pad information for INSTR1.
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR1 : Instruction 1
bits : 26 - 31 (6 bit)
access : read-write
Look-up Table register
address_offset : 0xDC68 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OPRND0 : Operand for INSTR0.
bits : 0 - 7 (8 bit)
access : read-write
PAD0 : Pad information for INSTR0.
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR0 : Instruction 0
bits : 10 - 15 (6 bit)
access : read-write
OPRND1 : Operand for INSTR1.
bits : 16 - 23 (8 bit)
access : read-write
PAD1 : Pad information for INSTR1.
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR1 : Instruction 1
bits : 26 - 31 (6 bit)
access : read-write
Look-up Table register
address_offset : 0xE074 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OPRND0 : Operand for INSTR0.
bits : 0 - 7 (8 bit)
access : read-write
PAD0 : Pad information for INSTR0.
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR0 : Instruction 0
bits : 10 - 15 (6 bit)
access : read-write
OPRND1 : Operand for INSTR1.
bits : 16 - 23 (8 bit)
access : read-write
PAD1 : Pad information for INSTR1.
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR1 : Instruction 1
bits : 26 - 31 (6 bit)
access : read-write
RX Buffer Data Register
address_offset : 0xE3C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RXDATA : no description available
bits : 0 - 31 (32 bit)
access : read-write
Look-up Table register
address_offset : 0xF90 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OPRND0 : Operand for INSTR0.
bits : 0 - 7 (8 bit)
access : read-write
PAD0 : Pad information for INSTR0.
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR0 : Instruction 0
bits : 10 - 15 (6 bit)
access : read-write
OPRND1 : Operand for INSTR1.
bits : 16 - 23 (8 bit)
access : read-write
PAD1 : Pad information for INSTR1.
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
#00 : 00
1 Pad
#01 : 01
2 Pads
#10 : 10
4 Pads
#11 : 11
NA
End of enumeration elements list.
INSTR1 : Instruction 1
bits : 26 - 31 (6 bit)
access : read-write
Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !
This website is sponsored by Embeetle, an IDE designed from scratch for embedded software developers.