Embeetle, an IDE designed from scratch for embedded software developers.address_offset : 0x0 Bytes (0x0)
size : 0xB00 byte (0x0)
mem_usage : registers
protection : not protected
Module Configuration Register
address_offset : 0x0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MAXMB : Number Of The Last Message Buffer
bits : 0 - 6 (7 bit)
access : read-write
RESERVED : no description available
bits : 7 - 7 (1 bit)
access : read-only
IDAM : ID Acceptance Mode
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
#00 : 00
Format A: One full ID (standard and extended) per ID Filter Table element.
#01 : 01
Format B: Two full standard IDs or two partial 14-bit (standard and extended) IDs per ID Filter Table element.
#10 : 10
Format C: Four partial 8-bit Standard IDs per ID Filter Table element.
#11 : 11
Format D: All frames rejected.
End of enumeration elements list.
RESERVED : no description available
bits : 10 - 11 (2 bit)
access : read-only
AEN : Abort Enable
bits : 12 - 12 (1 bit)
access : read-write
Enumeration:
#0 : 0
Abort disabled.
#1 : 1
Abort enabled.
End of enumeration elements list.
LPRIOEN : Local Priority Enable
bits : 13 - 13 (1 bit)
access : read-write
Enumeration:
#0 : 0
Local Priority disabled.
#1 : 1
Local Priority enabled.
End of enumeration elements list.
RESERVED : no description available
bits : 14 - 14 (1 bit)
access : read-write
RESERVED : no description available
bits : 15 - 15 (1 bit)
access : read-write
IRMQ : Individual Rx Masking And Queue Enable
bits : 16 - 16 (1 bit)
access : read-write
Enumeration:
#0 : 0
Individual Rx masking and queue feature are disabled. For backward compatibility with legacy applications, the reading of C/S word locks the MB even if it is EMPTY.
#1 : 1
Individual Rx masking and queue feature are enabled.
End of enumeration elements list.
SRXDIS : Self Reception Disable
bits : 17 - 17 (1 bit)
access : read-write
Enumeration:
#0 : 0
Self reception enabled.
#1 : 1
Self reception disabled.
End of enumeration elements list.
RESERVED : no description available
bits : 18 - 18 (1 bit)
access : read-only
RESERVED : no description available
bits : 19 - 19 (1 bit)
access : read-only
LPMACK : Low-Power Mode Acknowledge
bits : 20 - 20 (1 bit)
access : read-only
Enumeration:
#0 : 0
FlexCAN is not in a low-power mode.
#1 : 1
FlexCAN is in a low-power mode.
End of enumeration elements list.
WRNEN : Warning Interrupt Enable
bits : 21 - 21 (1 bit)
access : read-write
Enumeration:
#0 : 0
TWRNINT and RWRNINT bits are zero, independent of the values in the error counters.
#1 : 1
TWRNINT and RWRNINT bits are set when the respective error counter transitions from less than 96 to greater than or equal to 96.
End of enumeration elements list.
RESERVED : no description available
bits : 22 - 22 (1 bit)
access : read-only
SUPV : Supervisor Mode
bits : 23 - 23 (1 bit)
access : read-write
Enumeration:
#0 : 0
FlexCAN is in User mode. Affected registers allow both Supervisor and Unrestricted accesses .
#1 : 1
FlexCAN is in Supervisor mode. Affected registers allow only Supervisor access. Unrestricted access behaves as though the access was done to an unimplemented register location .
End of enumeration elements list.
FRZACK : Freeze Mode Acknowledge
bits : 24 - 24 (1 bit)
access : read-only
Enumeration:
#0 : 0
FlexCAN not in Freeze mode, prescaler running.
#1 : 1
FlexCAN in Freeze mode, prescaler stopped.
End of enumeration elements list.
SOFTRST : Soft Reset
bits : 25 - 25 (1 bit)
access : read-write
Enumeration:
#0 : 0
No reset request.
#1 : 1
Resets the registers affected by soft reset.
End of enumeration elements list.
RESERVED : no description available
bits : 26 - 26 (1 bit)
access : read-only
NOTRDY : FlexCAN Not Ready
bits : 27 - 27 (1 bit)
access : read-only
Enumeration:
#0 : 0
FlexCAN module is either in Normal mode, Listen-Only mode or Loop-Back mode.
#1 : 1
FlexCAN module is either in Disable mode , Stop mode or Freeze mode.
End of enumeration elements list.
HALT : Halt FlexCAN
bits : 28 - 28 (1 bit)
access : read-write
Enumeration:
#0 : 0
No Freeze mode request.
#1 : 1
Enters Freeze mode if the FRZ bit is asserted.
End of enumeration elements list.
RFEN : Rx FIFO Enable
bits : 29 - 29 (1 bit)
access : read-write
Enumeration:
#0 : 0
Rx FIFO not enabled.
#1 : 1
Rx FIFO enabled.
End of enumeration elements list.
FRZ : Freeze Enable
bits : 30 - 30 (1 bit)
access : read-write
Enumeration:
#0 : 0
Not enabled to enter Freeze mode.
#1 : 1
Enabled to enter Freeze mode.
End of enumeration elements list.
MDIS : Module Disable
bits : 31 - 31 (1 bit)
access : read-write
Enumeration:
#0 : 0
Enable the FlexCAN module.
#1 : 1
Disable the FlexCAN module.
End of enumeration elements list.
Rx Mailboxes Global Mask Register
address_offset : 0x10 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MG : Rx Mailboxes Global Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Message Buffer 8 CS Register
address_offset : 0x100 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TIME_STAMP : Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer, captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus.
bits : 0 - 15 (16 bit)
access : read-write
DLC : Length of the data to be stored/transmitted.
bits : 16 - 19 (4 bit)
access : read-write
RTR : Remote Transmission Request. One/zero for remote/data frame.
bits : 20 - 20 (1 bit)
access : read-write
IDE : ID Extended. One/zero for extended/standard format frame.
bits : 21 - 21 (1 bit)
access : read-write
SRR : Substitute Remote Request. Contains a fixed recessive bit.
bits : 22 - 22 (1 bit)
access : read-write
RESERVED : Reserved
bits : 23 - 23 (1 bit)
access : read-only
CODE : Reserved
bits : 24 - 27 (4 bit)
access : read-write
RESERVED : Reserved
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : Reserved
bits : 29 - 29 (1 bit)
access : read-only
RESERVED : Reserved
bits : 30 - 30 (1 bit)
access : read-only
RESERVED : Reserved
bits : 31 - 31 (1 bit)
access : read-only
Message Buffer 8 ID Register
address_offset : 0x104 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXT : Contains extended (LOW word) identifier of message buffer.
bits : 0 - 17 (18 bit)
access : read-write
STD : Contains standard/extended (HIGH word) identifier of message buffer.
bits : 18 - 28 (11 bit)
access : read-write
PRIO : Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority.
bits : 29 - 31 (3 bit)
access : read-write
Rx Individual Mask Registers
address_offset : 0x10558 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MI : Individual Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Message Buffer 8 WORD0 Register
address_offset : 0x108 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_3 : Data byte 3 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_2 : Data byte 2 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_1 : Data byte 1 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_0 : Data byte 0 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 8 WORD1 Register
address_offset : 0x10C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_7 : Data byte 7 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_6 : Data byte 6 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_5 : Data byte 5 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_4 : Data byte 4 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Rx Individual Mask Registers
address_offset : 0x10E4C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MI : Individual Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Message Buffer 9 CS Register
address_offset : 0x110 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TIME_STAMP : Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer, captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus.
bits : 0 - 15 (16 bit)
access : read-write
DLC : Length of the data to be stored/transmitted.
bits : 16 - 19 (4 bit)
access : read-write
RTR : Remote Transmission Request. One/zero for remote/data frame.
bits : 20 - 20 (1 bit)
access : read-write
IDE : ID Extended. One/zero for extended/standard format frame.
bits : 21 - 21 (1 bit)
access : read-write
SRR : Substitute Remote Request. Contains a fixed recessive bit.
bits : 22 - 22 (1 bit)
access : read-write
RESERVED : Reserved
bits : 23 - 23 (1 bit)
access : read-only
CODE : Reserved
bits : 24 - 27 (4 bit)
access : read-write
RESERVED : Reserved
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : Reserved
bits : 29 - 29 (1 bit)
access : read-only
RESERVED : Reserved
bits : 30 - 30 (1 bit)
access : read-only
RESERVED : Reserved
bits : 31 - 31 (1 bit)
access : read-only
Rx Individual Mask Registers
address_offset : 0x1100 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MI : Individual Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Message Buffer 9 ID Register
address_offset : 0x114 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXT : Contains extended (LOW word) identifier of message buffer.
bits : 0 - 17 (18 bit)
access : read-write
STD : Contains standard/extended (HIGH word) identifier of message buffer.
bits : 18 - 28 (11 bit)
access : read-write
PRIO : Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority.
bits : 29 - 31 (3 bit)
access : read-write
Rx Individual Mask Registers
address_offset : 0x11744 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MI : Individual Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Message Buffer 9 WORD0 Register
address_offset : 0x118 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_3 : Data byte 3 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_2 : Data byte 2 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_1 : Data byte 1 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_0 : Data byte 0 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 9 WORD1 Register
address_offset : 0x11C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_7 : Data byte 7 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_6 : Data byte 6 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_5 : Data byte 5 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_4 : Data byte 4 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 10 CS Register
address_offset : 0x120 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TIME_STAMP : Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer, captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus.
bits : 0 - 15 (16 bit)
access : read-write
DLC : Length of the data to be stored/transmitted.
bits : 16 - 19 (4 bit)
access : read-write
RTR : Remote Transmission Request. One/zero for remote/data frame.
bits : 20 - 20 (1 bit)
access : read-write
IDE : ID Extended. One/zero for extended/standard format frame.
bits : 21 - 21 (1 bit)
access : read-write
SRR : Substitute Remote Request. Contains a fixed recessive bit.
bits : 22 - 22 (1 bit)
access : read-write
RESERVED : Reserved
bits : 23 - 23 (1 bit)
access : read-only
CODE : Reserved
bits : 24 - 27 (4 bit)
access : read-write
RESERVED : Reserved
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : Reserved
bits : 29 - 29 (1 bit)
access : read-only
RESERVED : Reserved
bits : 30 - 30 (1 bit)
access : read-only
RESERVED : Reserved
bits : 31 - 31 (1 bit)
access : read-only
Rx Individual Mask Registers
address_offset : 0x12040 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MI : Individual Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Message Buffer 10 ID Register
address_offset : 0x124 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXT : Contains extended (LOW word) identifier of message buffer.
bits : 0 - 17 (18 bit)
access : read-write
STD : Contains standard/extended (HIGH word) identifier of message buffer.
bits : 18 - 28 (11 bit)
access : read-write
PRIO : Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority.
bits : 29 - 31 (3 bit)
access : read-write
Message Buffer 10 WORD0 Register
address_offset : 0x128 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_3 : Data byte 3 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_2 : Data byte 2 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_1 : Data byte 1 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_0 : Data byte 0 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Rx Individual Mask Registers
address_offset : 0x12940 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MI : Individual Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Message Buffer 10 WORD1 Register
address_offset : 0x12C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_7 : Data byte 7 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_6 : Data byte 6 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_5 : Data byte 5 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_4 : Data byte 4 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 11 CS Register
address_offset : 0x130 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TIME_STAMP : Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer, captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus.
bits : 0 - 15 (16 bit)
access : read-write
DLC : Length of the data to be stored/transmitted.
bits : 16 - 19 (4 bit)
access : read-write
RTR : Remote Transmission Request. One/zero for remote/data frame.
bits : 20 - 20 (1 bit)
access : read-write
IDE : ID Extended. One/zero for extended/standard format frame.
bits : 21 - 21 (1 bit)
access : read-write
SRR : Substitute Remote Request. Contains a fixed recessive bit.
bits : 22 - 22 (1 bit)
access : read-write
RESERVED : Reserved
bits : 23 - 23 (1 bit)
access : read-only
CODE : Reserved
bits : 24 - 27 (4 bit)
access : read-write
RESERVED : Reserved
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : Reserved
bits : 29 - 29 (1 bit)
access : read-only
RESERVED : Reserved
bits : 30 - 30 (1 bit)
access : read-only
RESERVED : Reserved
bits : 31 - 31 (1 bit)
access : read-only
Rx Individual Mask Registers
address_offset : 0x13244 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MI : Individual Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Message Buffer 11 ID Register
address_offset : 0x134 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXT : Contains extended (LOW word) identifier of message buffer.
bits : 0 - 17 (18 bit)
access : read-write
STD : Contains standard/extended (HIGH word) identifier of message buffer.
bits : 18 - 28 (11 bit)
access : read-write
PRIO : Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority.
bits : 29 - 31 (3 bit)
access : read-write
Message Buffer 11 WORD0 Register
address_offset : 0x138 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_3 : Data byte 3 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_2 : Data byte 2 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_1 : Data byte 1 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_0 : Data byte 0 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Rx Individual Mask Registers
address_offset : 0x13B4C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MI : Individual Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Message Buffer 11 WORD1 Register
address_offset : 0x13C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_7 : Data byte 7 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_6 : Data byte 6 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_5 : Data byte 5 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_4 : Data byte 4 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Rx 14 Mask register
address_offset : 0x14 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RX14M : Rx Buffer 14 Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Message Buffer 12 CS Register
address_offset : 0x140 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TIME_STAMP : Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer, captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus.
bits : 0 - 15 (16 bit)
access : read-write
DLC : Length of the data to be stored/transmitted.
bits : 16 - 19 (4 bit)
access : read-write
RTR : Remote Transmission Request. One/zero for remote/data frame.
bits : 20 - 20 (1 bit)
access : read-write
IDE : ID Extended. One/zero for extended/standard format frame.
bits : 21 - 21 (1 bit)
access : read-write
SRR : Substitute Remote Request. Contains a fixed recessive bit.
bits : 22 - 22 (1 bit)
access : read-write
RESERVED : Reserved
bits : 23 - 23 (1 bit)
access : read-only
CODE : Reserved
bits : 24 - 27 (4 bit)
access : read-write
RESERVED : Reserved
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : Reserved
bits : 29 - 29 (1 bit)
access : read-only
RESERVED : Reserved
bits : 30 - 30 (1 bit)
access : read-only
RESERVED : Reserved
bits : 31 - 31 (1 bit)
access : read-only
Message Buffer 12 ID Register
address_offset : 0x144 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXT : Contains extended (LOW word) identifier of message buffer.
bits : 0 - 17 (18 bit)
access : read-write
STD : Contains standard/extended (HIGH word) identifier of message buffer.
bits : 18 - 28 (11 bit)
access : read-write
PRIO : Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority.
bits : 29 - 31 (3 bit)
access : read-write
Rx Individual Mask Registers
address_offset : 0x14458 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MI : Individual Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Message Buffer 12 WORD0 Register
address_offset : 0x148 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_3 : Data byte 3 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_2 : Data byte 2 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_1 : Data byte 1 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_0 : Data byte 0 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 12 WORD1 Register
address_offset : 0x14C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_7 : Data byte 7 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_6 : Data byte 6 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_5 : Data byte 5 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_4 : Data byte 4 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Rx Individual Mask Registers
address_offset : 0x14D68 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MI : Individual Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Message Buffer 13 CS Register
address_offset : 0x150 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TIME_STAMP : Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer, captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus.
bits : 0 - 15 (16 bit)
access : read-write
DLC : Length of the data to be stored/transmitted.
bits : 16 - 19 (4 bit)
access : read-write
RTR : Remote Transmission Request. One/zero for remote/data frame.
bits : 20 - 20 (1 bit)
access : read-write
IDE : ID Extended. One/zero for extended/standard format frame.
bits : 21 - 21 (1 bit)
access : read-write
SRR : Substitute Remote Request. Contains a fixed recessive bit.
bits : 22 - 22 (1 bit)
access : read-write
RESERVED : Reserved
bits : 23 - 23 (1 bit)
access : read-only
CODE : Reserved
bits : 24 - 27 (4 bit)
access : read-write
RESERVED : Reserved
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : Reserved
bits : 29 - 29 (1 bit)
access : read-only
RESERVED : Reserved
bits : 30 - 30 (1 bit)
access : read-only
RESERVED : Reserved
bits : 31 - 31 (1 bit)
access : read-only
Message Buffer 13 ID Register
address_offset : 0x154 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXT : Contains extended (LOW word) identifier of message buffer.
bits : 0 - 17 (18 bit)
access : read-write
STD : Contains standard/extended (HIGH word) identifier of message buffer.
bits : 18 - 28 (11 bit)
access : read-write
PRIO : Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority.
bits : 29 - 31 (3 bit)
access : read-write
Rx Individual Mask Registers
address_offset : 0x1567C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MI : Individual Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Message Buffer 13 WORD0 Register
address_offset : 0x158 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_3 : Data byte 3 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_2 : Data byte 2 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_1 : Data byte 1 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_0 : Data byte 0 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 13 WORD1 Register
address_offset : 0x15C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_7 : Data byte 7 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_6 : Data byte 6 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_5 : Data byte 5 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_4 : Data byte 4 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Rx Individual Mask Registers
address_offset : 0x15F94 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MI : Individual Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Message Buffer 14 CS Register
address_offset : 0x160 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TIME_STAMP : Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer, captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus.
bits : 0 - 15 (16 bit)
access : read-write
DLC : Length of the data to be stored/transmitted.
bits : 16 - 19 (4 bit)
access : read-write
RTR : Remote Transmission Request. One/zero for remote/data frame.
bits : 20 - 20 (1 bit)
access : read-write
IDE : ID Extended. One/zero for extended/standard format frame.
bits : 21 - 21 (1 bit)
access : read-write
SRR : Substitute Remote Request. Contains a fixed recessive bit.
bits : 22 - 22 (1 bit)
access : read-write
RESERVED : Reserved
bits : 23 - 23 (1 bit)
access : read-only
CODE : Reserved
bits : 24 - 27 (4 bit)
access : read-write
RESERVED : Reserved
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : Reserved
bits : 29 - 29 (1 bit)
access : read-only
RESERVED : Reserved
bits : 30 - 30 (1 bit)
access : read-only
RESERVED : Reserved
bits : 31 - 31 (1 bit)
access : read-only
Message Buffer 14 ID Register
address_offset : 0x164 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXT : Contains extended (LOW word) identifier of message buffer.
bits : 0 - 17 (18 bit)
access : read-write
STD : Contains standard/extended (HIGH word) identifier of message buffer.
bits : 18 - 28 (11 bit)
access : read-write
PRIO : Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority.
bits : 29 - 31 (3 bit)
access : read-write
Message Buffer 14 WORD0 Register
address_offset : 0x168 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_3 : Data byte 3 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_2 : Data byte 2 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_1 : Data byte 1 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_0 : Data byte 0 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Rx Individual Mask Registers
address_offset : 0x168B0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MI : Individual Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Message Buffer 14 WORD1 Register
address_offset : 0x16C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_7 : Data byte 7 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_6 : Data byte 6 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_5 : Data byte 5 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_4 : Data byte 4 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 15 CS Register
address_offset : 0x170 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TIME_STAMP : Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer, captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus.
bits : 0 - 15 (16 bit)
access : read-write
DLC : Length of the data to be stored/transmitted.
bits : 16 - 19 (4 bit)
access : read-write
RTR : Remote Transmission Request. One/zero for remote/data frame.
bits : 20 - 20 (1 bit)
access : read-write
IDE : ID Extended. One/zero for extended/standard format frame.
bits : 21 - 21 (1 bit)
access : read-write
SRR : Substitute Remote Request. Contains a fixed recessive bit.
bits : 22 - 22 (1 bit)
access : read-write
RESERVED : Reserved
bits : 23 - 23 (1 bit)
access : read-only
CODE : Reserved
bits : 24 - 27 (4 bit)
access : read-write
RESERVED : Reserved
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : Reserved
bits : 29 - 29 (1 bit)
access : read-only
RESERVED : Reserved
bits : 30 - 30 (1 bit)
access : read-only
RESERVED : Reserved
bits : 31 - 31 (1 bit)
access : read-only
Rx Individual Mask Registers
address_offset : 0x171D0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MI : Individual Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Message Buffer 15 ID Register
address_offset : 0x174 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXT : Contains extended (LOW word) identifier of message buffer.
bits : 0 - 17 (18 bit)
access : read-write
STD : Contains standard/extended (HIGH word) identifier of message buffer.
bits : 18 - 28 (11 bit)
access : read-write
PRIO : Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority.
bits : 29 - 31 (3 bit)
access : read-write
Message Buffer 15 WORD0 Register
address_offset : 0x178 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_3 : Data byte 3 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_2 : Data byte 2 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_1 : Data byte 1 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_0 : Data byte 0 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Rx Individual Mask Registers
address_offset : 0x17AF4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MI : Individual Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Message Buffer 15 WORD1 Register
address_offset : 0x17C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_7 : Data byte 7 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_6 : Data byte 6 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_5 : Data byte 5 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_4 : Data byte 4 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Rx 15 Mask register
address_offset : 0x18 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RX15M : Rx Buffer 15 Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Message Buffer 16 CS Register
address_offset : 0x180 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TIME_STAMP : Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer, captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus.
bits : 0 - 15 (16 bit)
access : read-write
DLC : Length of the data to be stored/transmitted.
bits : 16 - 19 (4 bit)
access : read-write
RTR : Remote Transmission Request. One/zero for remote/data frame.
bits : 20 - 20 (1 bit)
access : read-write
IDE : ID Extended. One/zero for extended/standard format frame.
bits : 21 - 21 (1 bit)
access : read-write
SRR : Substitute Remote Request. Contains a fixed recessive bit.
bits : 22 - 22 (1 bit)
access : read-write
RESERVED : Reserved
bits : 23 - 23 (1 bit)
access : read-only
CODE : Reserved
bits : 24 - 27 (4 bit)
access : read-write
RESERVED : Reserved
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : Reserved
bits : 29 - 29 (1 bit)
access : read-only
RESERVED : Reserved
bits : 30 - 30 (1 bit)
access : read-only
RESERVED : Reserved
bits : 31 - 31 (1 bit)
access : read-only
Message Buffer 16 ID Register
address_offset : 0x184 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXT : Contains extended (LOW word) identifier of message buffer.
bits : 0 - 17 (18 bit)
access : read-write
STD : Contains standard/extended (HIGH word) identifier of message buffer.
bits : 18 - 28 (11 bit)
access : read-write
PRIO : Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority.
bits : 29 - 31 (3 bit)
access : read-write
Rx Individual Mask Registers
address_offset : 0x1841C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MI : Individual Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Message Buffer 16 WORD0 Register
address_offset : 0x188 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_3 : Data byte 3 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_2 : Data byte 2 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_1 : Data byte 1 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_0 : Data byte 0 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 16 WORD1 Register
address_offset : 0x18C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_7 : Data byte 7 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_6 : Data byte 6 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_5 : Data byte 5 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_4 : Data byte 4 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Rx Individual Mask Registers
address_offset : 0x18D48 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MI : Individual Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Message Buffer 17 CS Register
address_offset : 0x190 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TIME_STAMP : Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer, captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus.
bits : 0 - 15 (16 bit)
access : read-write
DLC : Length of the data to be stored/transmitted.
bits : 16 - 19 (4 bit)
access : read-write
RTR : Remote Transmission Request. One/zero for remote/data frame.
bits : 20 - 20 (1 bit)
access : read-write
IDE : ID Extended. One/zero for extended/standard format frame.
bits : 21 - 21 (1 bit)
access : read-write
SRR : Substitute Remote Request. Contains a fixed recessive bit.
bits : 22 - 22 (1 bit)
access : read-write
RESERVED : Reserved
bits : 23 - 23 (1 bit)
access : read-only
CODE : Reserved
bits : 24 - 27 (4 bit)
access : read-write
RESERVED : Reserved
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : Reserved
bits : 29 - 29 (1 bit)
access : read-only
RESERVED : Reserved
bits : 30 - 30 (1 bit)
access : read-only
RESERVED : Reserved
bits : 31 - 31 (1 bit)
access : read-only
Message Buffer 17 ID Register
address_offset : 0x194 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXT : Contains extended (LOW word) identifier of message buffer.
bits : 0 - 17 (18 bit)
access : read-write
STD : Contains standard/extended (HIGH word) identifier of message buffer.
bits : 18 - 28 (11 bit)
access : read-write
PRIO : Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority.
bits : 29 - 31 (3 bit)
access : read-write
Rx Individual Mask Registers
address_offset : 0x19678 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MI : Individual Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Message Buffer 17 WORD0 Register
address_offset : 0x198 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_3 : Data byte 3 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_2 : Data byte 2 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_1 : Data byte 1 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_0 : Data byte 0 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Rx Individual Mask Registers
address_offset : 0x1984 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MI : Individual Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Message Buffer 17 WORD1 Register
address_offset : 0x19C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_7 : Data byte 7 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_6 : Data byte 6 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_5 : Data byte 5 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_4 : Data byte 4 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Rx Individual Mask Registers
address_offset : 0x19FAC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MI : Individual Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Message Buffer 18 CS Register
address_offset : 0x1A0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TIME_STAMP : Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer, captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus.
bits : 0 - 15 (16 bit)
access : read-write
DLC : Length of the data to be stored/transmitted.
bits : 16 - 19 (4 bit)
access : read-write
RTR : Remote Transmission Request. One/zero for remote/data frame.
bits : 20 - 20 (1 bit)
access : read-write
IDE : ID Extended. One/zero for extended/standard format frame.
bits : 21 - 21 (1 bit)
access : read-write
SRR : Substitute Remote Request. Contains a fixed recessive bit.
bits : 22 - 22 (1 bit)
access : read-write
RESERVED : Reserved
bits : 23 - 23 (1 bit)
access : read-only
CODE : Reserved
bits : 24 - 27 (4 bit)
access : read-write
RESERVED : Reserved
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : Reserved
bits : 29 - 29 (1 bit)
access : read-only
RESERVED : Reserved
bits : 30 - 30 (1 bit)
access : read-only
RESERVED : Reserved
bits : 31 - 31 (1 bit)
access : read-only
Message Buffer 18 ID Register
address_offset : 0x1A4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXT : Contains extended (LOW word) identifier of message buffer.
bits : 0 - 17 (18 bit)
access : read-write
STD : Contains standard/extended (HIGH word) identifier of message buffer.
bits : 18 - 28 (11 bit)
access : read-write
PRIO : Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority.
bits : 29 - 31 (3 bit)
access : read-write
Message Buffer 18 WORD0 Register
address_offset : 0x1A8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_3 : Data byte 3 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_2 : Data byte 2 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_1 : Data byte 1 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_0 : Data byte 0 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Rx Individual Mask Registers
address_offset : 0x1A8E4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MI : Individual Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Message Buffer 18 WORD1 Register
address_offset : 0x1AC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_7 : Data byte 7 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_6 : Data byte 6 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_5 : Data byte 5 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_4 : Data byte 4 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 19 CS Register
address_offset : 0x1B0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TIME_STAMP : Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer, captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus.
bits : 0 - 15 (16 bit)
access : read-write
DLC : Length of the data to be stored/transmitted.
bits : 16 - 19 (4 bit)
access : read-write
RTR : Remote Transmission Request. One/zero for remote/data frame.
bits : 20 - 20 (1 bit)
access : read-write
IDE : ID Extended. One/zero for extended/standard format frame.
bits : 21 - 21 (1 bit)
access : read-write
SRR : Substitute Remote Request. Contains a fixed recessive bit.
bits : 22 - 22 (1 bit)
access : read-write
RESERVED : Reserved
bits : 23 - 23 (1 bit)
access : read-only
CODE : Reserved
bits : 24 - 27 (4 bit)
access : read-write
RESERVED : Reserved
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : Reserved
bits : 29 - 29 (1 bit)
access : read-only
RESERVED : Reserved
bits : 30 - 30 (1 bit)
access : read-only
RESERVED : Reserved
bits : 31 - 31 (1 bit)
access : read-only
Rx Individual Mask Registers
address_offset : 0x1B220 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MI : Individual Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Message Buffer 19 ID Register
address_offset : 0x1B4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXT : Contains extended (LOW word) identifier of message buffer.
bits : 0 - 17 (18 bit)
access : read-write
STD : Contains standard/extended (HIGH word) identifier of message buffer.
bits : 18 - 28 (11 bit)
access : read-write
PRIO : Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority.
bits : 29 - 31 (3 bit)
access : read-write
Message Buffer 19 WORD0 Register
address_offset : 0x1B8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_3 : Data byte 3 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_2 : Data byte 2 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_1 : Data byte 1 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_0 : Data byte 0 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Rx Individual Mask Registers
address_offset : 0x1BB60 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MI : Individual Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Message Buffer 19 WORD1 Register
address_offset : 0x1BC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_7 : Data byte 7 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_6 : Data byte 6 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_5 : Data byte 5 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_4 : Data byte 4 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Error Counter
address_offset : 0x1C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TXERRCNT : Transmit Error Counter
bits : 0 - 7 (8 bit)
access : read-write
RXERRCNT : Receive Error Counter
bits : 8 - 15 (8 bit)
access : read-write
RESERVED : no description available
bits : 16 - 31 (16 bit)
access : read-only
Message Buffer 20 CS Register
address_offset : 0x1C0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TIME_STAMP : Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer, captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus.
bits : 0 - 15 (16 bit)
access : read-write
DLC : Length of the data to be stored/transmitted.
bits : 16 - 19 (4 bit)
access : read-write
RTR : Remote Transmission Request. One/zero for remote/data frame.
bits : 20 - 20 (1 bit)
access : read-write
IDE : ID Extended. One/zero for extended/standard format frame.
bits : 21 - 21 (1 bit)
access : read-write
SRR : Substitute Remote Request. Contains a fixed recessive bit.
bits : 22 - 22 (1 bit)
access : read-write
RESERVED : Reserved
bits : 23 - 23 (1 bit)
access : read-only
CODE : Reserved
bits : 24 - 27 (4 bit)
access : read-write
RESERVED : Reserved
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : Reserved
bits : 29 - 29 (1 bit)
access : read-only
RESERVED : Reserved
bits : 30 - 30 (1 bit)
access : read-only
RESERVED : Reserved
bits : 31 - 31 (1 bit)
access : read-only
Message Buffer 20 ID Register
address_offset : 0x1C4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXT : Contains extended (LOW word) identifier of message buffer.
bits : 0 - 17 (18 bit)
access : read-write
STD : Contains standard/extended (HIGH word) identifier of message buffer.
bits : 18 - 28 (11 bit)
access : read-write
PRIO : Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority.
bits : 29 - 31 (3 bit)
access : read-write
Rx Individual Mask Registers
address_offset : 0x1C4A4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MI : Individual Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Message Buffer 20 WORD0 Register
address_offset : 0x1C8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_3 : Data byte 3 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_2 : Data byte 2 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_1 : Data byte 1 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_0 : Data byte 0 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 20 WORD1 Register
address_offset : 0x1CC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_7 : Data byte 7 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_6 : Data byte 6 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_5 : Data byte 5 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_4 : Data byte 4 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Rx Individual Mask Registers
address_offset : 0x1CDEC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MI : Individual Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Message Buffer 21 CS Register
address_offset : 0x1D0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TIME_STAMP : Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer, captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus.
bits : 0 - 15 (16 bit)
access : read-write
DLC : Length of the data to be stored/transmitted.
bits : 16 - 19 (4 bit)
access : read-write
RTR : Remote Transmission Request. One/zero for remote/data frame.
bits : 20 - 20 (1 bit)
access : read-write
IDE : ID Extended. One/zero for extended/standard format frame.
bits : 21 - 21 (1 bit)
access : read-write
SRR : Substitute Remote Request. Contains a fixed recessive bit.
bits : 22 - 22 (1 bit)
access : read-write
RESERVED : Reserved
bits : 23 - 23 (1 bit)
access : read-only
CODE : Reserved
bits : 24 - 27 (4 bit)
access : read-write
RESERVED : Reserved
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : Reserved
bits : 29 - 29 (1 bit)
access : read-only
RESERVED : Reserved
bits : 30 - 30 (1 bit)
access : read-only
RESERVED : Reserved
bits : 31 - 31 (1 bit)
access : read-only
Message Buffer 21 ID Register
address_offset : 0x1D4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXT : Contains extended (LOW word) identifier of message buffer.
bits : 0 - 17 (18 bit)
access : read-write
STD : Contains standard/extended (HIGH word) identifier of message buffer.
bits : 18 - 28 (11 bit)
access : read-write
PRIO : Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority.
bits : 29 - 31 (3 bit)
access : read-write
Rx Individual Mask Registers
address_offset : 0x1D738 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MI : Individual Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Message Buffer 21 WORD0 Register
address_offset : 0x1D8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_3 : Data byte 3 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_2 : Data byte 2 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_1 : Data byte 1 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_0 : Data byte 0 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 21 WORD1 Register
address_offset : 0x1DC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_7 : Data byte 7 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_6 : Data byte 6 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_5 : Data byte 5 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_4 : Data byte 4 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 22 CS Register
address_offset : 0x1E0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TIME_STAMP : Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer, captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus.
bits : 0 - 15 (16 bit)
access : read-write
DLC : Length of the data to be stored/transmitted.
bits : 16 - 19 (4 bit)
access : read-write
RTR : Remote Transmission Request. One/zero for remote/data frame.
bits : 20 - 20 (1 bit)
access : read-write
IDE : ID Extended. One/zero for extended/standard format frame.
bits : 21 - 21 (1 bit)
access : read-write
SRR : Substitute Remote Request. Contains a fixed recessive bit.
bits : 22 - 22 (1 bit)
access : read-write
RESERVED : Reserved
bits : 23 - 23 (1 bit)
access : read-only
CODE : Reserved
bits : 24 - 27 (4 bit)
access : read-write
RESERVED : Reserved
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : Reserved
bits : 29 - 29 (1 bit)
access : read-only
RESERVED : Reserved
bits : 30 - 30 (1 bit)
access : read-only
RESERVED : Reserved
bits : 31 - 31 (1 bit)
access : read-only
Rx Individual Mask Registers
address_offset : 0x1E088 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MI : Individual Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Message Buffer 22 ID Register
address_offset : 0x1E4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXT : Contains extended (LOW word) identifier of message buffer.
bits : 0 - 17 (18 bit)
access : read-write
STD : Contains standard/extended (HIGH word) identifier of message buffer.
bits : 18 - 28 (11 bit)
access : read-write
PRIO : Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority.
bits : 29 - 31 (3 bit)
access : read-write
Message Buffer 22 WORD0 Register
address_offset : 0x1E8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_3 : Data byte 3 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_2 : Data byte 2 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_1 : Data byte 1 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_0 : Data byte 0 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Rx Individual Mask Registers
address_offset : 0x1E9DC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MI : Individual Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Message Buffer 22 WORD1 Register
address_offset : 0x1EC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_7 : Data byte 7 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_6 : Data byte 6 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_5 : Data byte 5 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_4 : Data byte 4 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 23 CS Register
address_offset : 0x1F0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TIME_STAMP : Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer, captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus.
bits : 0 - 15 (16 bit)
access : read-write
DLC : Length of the data to be stored/transmitted.
bits : 16 - 19 (4 bit)
access : read-write
RTR : Remote Transmission Request. One/zero for remote/data frame.
bits : 20 - 20 (1 bit)
access : read-write
IDE : ID Extended. One/zero for extended/standard format frame.
bits : 21 - 21 (1 bit)
access : read-write
SRR : Substitute Remote Request. Contains a fixed recessive bit.
bits : 22 - 22 (1 bit)
access : read-write
RESERVED : Reserved
bits : 23 - 23 (1 bit)
access : read-only
CODE : Reserved
bits : 24 - 27 (4 bit)
access : read-write
RESERVED : Reserved
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : Reserved
bits : 29 - 29 (1 bit)
access : read-only
RESERVED : Reserved
bits : 30 - 30 (1 bit)
access : read-only
RESERVED : Reserved
bits : 31 - 31 (1 bit)
access : read-only
Rx Individual Mask Registers
address_offset : 0x1F334 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MI : Individual Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Message Buffer 23 ID Register
address_offset : 0x1F4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXT : Contains extended (LOW word) identifier of message buffer.
bits : 0 - 17 (18 bit)
access : read-write
STD : Contains standard/extended (HIGH word) identifier of message buffer.
bits : 18 - 28 (11 bit)
access : read-write
PRIO : Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority.
bits : 29 - 31 (3 bit)
access : read-write
Message Buffer 23 WORD0 Register
address_offset : 0x1F8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_3 : Data byte 3 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_2 : Data byte 2 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_1 : Data byte 1 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_0 : Data byte 0 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 23 WORD1 Register
address_offset : 0x1FC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_7 : Data byte 7 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_6 : Data byte 6 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_5 : Data byte 5 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_4 : Data byte 4 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Rx Individual Mask Registers
address_offset : 0x1FC90 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MI : Individual Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Error and Status 1 register
address_offset : 0x20 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RESERVED : no description available
bits : 0 - 0 (1 bit)
access : read-only
ERRINT : Error Interrupt
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
No such occurrence.
#1 : 1
Indicates setting of any Error Bit in the Error and Status Register.
End of enumeration elements list.
BOFFINT : Bus Off Interrupt
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
No such occurrence.
#1 : 1
FlexCAN module entered Bus Off state.
End of enumeration elements list.
RX : FlexCAN In Reception
bits : 3 - 3 (1 bit)
access : read-only
Enumeration:
#0 : 0
FlexCAN is not receiving a message.
#1 : 1
FlexCAN is receiving a message.
End of enumeration elements list.
FLTCONF : Fault Confinement State
bits : 4 - 5 (2 bit)
access : read-only
Enumeration:
#00 : 00
Error Active
#01 : 01
Error Passive
#1x : 1x
Bus Off
End of enumeration elements list.
TX : FlexCAN In Transmission
bits : 6 - 6 (1 bit)
access : read-only
Enumeration:
#0 : 0
FlexCAN is not transmitting a message.
#1 : 1
FlexCAN is transmitting a message.
End of enumeration elements list.
IDLE : no description available
bits : 7 - 7 (1 bit)
access : read-only
Enumeration:
#0 : 0
No such occurrence.
#1 : 1
CAN bus is now IDLE.
End of enumeration elements list.
RXWRN : Rx Error Warning
bits : 8 - 8 (1 bit)
access : read-only
Enumeration:
#0 : 0
No such occurrence.
#1 : 1
RXERRCNT is greater than or equal to 96.
End of enumeration elements list.
TXWRN : TX Error Warning
bits : 9 - 9 (1 bit)
access : read-only
Enumeration:
#0 : 0
No such occurrence.
#1 : 1
TXERRCNT is greater than or equal to 96.
End of enumeration elements list.
STFERR : Stuffing Error
bits : 10 - 10 (1 bit)
access : read-only
Enumeration:
#0 : 0
No such occurrence.
#1 : 1
A Stuffing Error occurred since last read of this register.
End of enumeration elements list.
FRMERR : Form Error
bits : 11 - 11 (1 bit)
access : read-only
Enumeration:
#0 : 0
No such occurrence.
#1 : 1
A Form Error occurred since last read of this register.
End of enumeration elements list.
CRCERR : Cyclic Redundancy Check Error
bits : 12 - 12 (1 bit)
access : read-only
Enumeration:
#0 : 0
No such occurrence.
#1 : 1
A CRC error occurred since last read of this register.
End of enumeration elements list.
ACKERR : Acknowledge Error
bits : 13 - 13 (1 bit)
access : read-only
Enumeration:
#0 : 0
No such occurrence.
#1 : 1
An ACK error occurred since last read of this register.
End of enumeration elements list.
BIT0ERR : Bit0 Error
bits : 14 - 14 (1 bit)
access : read-only
Enumeration:
#0 : 0
No such occurrence.
#1 : 1
At least one bit sent as dominant is received as recessive.
End of enumeration elements list.
BIT1ERR : Bit1 Error
bits : 15 - 15 (1 bit)
access : read-only
Enumeration:
#0 : 0
No such occurrence.
#1 : 1
At least one bit sent as recessive is received as dominant.
End of enumeration elements list.
RWRNINT : Rx Warning Interrupt Flag
bits : 16 - 16 (1 bit)
access : read-write
Enumeration:
#0 : 0
No such occurrence.
#1 : 1
The Rx error counter transitioned from less than 96 to greater than or equal to 96.
End of enumeration elements list.
TWRNINT : Tx Warning Interrupt Flag
bits : 17 - 17 (1 bit)
access : read-write
Enumeration:
#0 : 0
No such occurrence.
#1 : 1
The Tx error counter transitioned from less than 96 to greater than or equal to 96.
End of enumeration elements list.
SYNCH : CAN Synchronization Status
bits : 18 - 18 (1 bit)
access : read-only
Enumeration:
#0 : 0
FlexCAN is not synchronized to the CAN bus.
#1 : 1
FlexCAN is synchronized to the CAN bus.
End of enumeration elements list.
RESERVED : no description available
bits : 19 - 31 (13 bit)
access : read-only
Message Buffer 24 CS Register
address_offset : 0x200 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TIME_STAMP : Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer, captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus.
bits : 0 - 15 (16 bit)
access : read-write
DLC : Length of the data to be stored/transmitted.
bits : 16 - 19 (4 bit)
access : read-write
RTR : Remote Transmission Request. One/zero for remote/data frame.
bits : 20 - 20 (1 bit)
access : read-write
IDE : ID Extended. One/zero for extended/standard format frame.
bits : 21 - 21 (1 bit)
access : read-write
SRR : Substitute Remote Request. Contains a fixed recessive bit.
bits : 22 - 22 (1 bit)
access : read-write
RESERVED : Reserved
bits : 23 - 23 (1 bit)
access : read-only
CODE : Reserved
bits : 24 - 27 (4 bit)
access : read-write
RESERVED : Reserved
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : Reserved
bits : 29 - 29 (1 bit)
access : read-only
RESERVED : Reserved
bits : 30 - 30 (1 bit)
access : read-only
RESERVED : Reserved
bits : 31 - 31 (1 bit)
access : read-only
Message Buffer 24 ID Register
address_offset : 0x204 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXT : Contains extended (LOW word) identifier of message buffer.
bits : 0 - 17 (18 bit)
access : read-write
STD : Contains standard/extended (HIGH word) identifier of message buffer.
bits : 18 - 28 (11 bit)
access : read-write
PRIO : Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority.
bits : 29 - 31 (3 bit)
access : read-write
Rx Individual Mask Registers
address_offset : 0x205F0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MI : Individual Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Message Buffer 24 WORD0 Register
address_offset : 0x208 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_3 : Data byte 3 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_2 : Data byte 2 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_1 : Data byte 1 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_0 : Data byte 0 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 24 WORD1 Register
address_offset : 0x20C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_7 : Data byte 7 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_6 : Data byte 6 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_5 : Data byte 5 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_4 : Data byte 4 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Rx Individual Mask Registers
address_offset : 0x20F54 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MI : Individual Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Message Buffer 25 CS Register
address_offset : 0x210 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TIME_STAMP : Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer, captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus.
bits : 0 - 15 (16 bit)
access : read-write
DLC : Length of the data to be stored/transmitted.
bits : 16 - 19 (4 bit)
access : read-write
RTR : Remote Transmission Request. One/zero for remote/data frame.
bits : 20 - 20 (1 bit)
access : read-write
IDE : ID Extended. One/zero for extended/standard format frame.
bits : 21 - 21 (1 bit)
access : read-write
SRR : Substitute Remote Request. Contains a fixed recessive bit.
bits : 22 - 22 (1 bit)
access : read-write
RESERVED : Reserved
bits : 23 - 23 (1 bit)
access : read-only
CODE : Reserved
bits : 24 - 27 (4 bit)
access : read-write
RESERVED : Reserved
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : Reserved
bits : 29 - 29 (1 bit)
access : read-only
RESERVED : Reserved
bits : 30 - 30 (1 bit)
access : read-only
RESERVED : Reserved
bits : 31 - 31 (1 bit)
access : read-only
Message Buffer 25 ID Register
address_offset : 0x214 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXT : Contains extended (LOW word) identifier of message buffer.
bits : 0 - 17 (18 bit)
access : read-write
STD : Contains standard/extended (HIGH word) identifier of message buffer.
bits : 18 - 28 (11 bit)
access : read-write
PRIO : Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority.
bits : 29 - 31 (3 bit)
access : read-write
Message Buffer 25 WORD0 Register
address_offset : 0x218 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_3 : Data byte 3 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_2 : Data byte 2 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_1 : Data byte 1 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_0 : Data byte 0 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Rx Individual Mask Registers
address_offset : 0x218BC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MI : Individual Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Message Buffer 25 WORD1 Register
address_offset : 0x21C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_7 : Data byte 7 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_6 : Data byte 6 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_5 : Data byte 5 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_4 : Data byte 4 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 26 CS Register
address_offset : 0x220 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TIME_STAMP : Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer, captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus.
bits : 0 - 15 (16 bit)
access : read-write
DLC : Length of the data to be stored/transmitted.
bits : 16 - 19 (4 bit)
access : read-write
RTR : Remote Transmission Request. One/zero for remote/data frame.
bits : 20 - 20 (1 bit)
access : read-write
IDE : ID Extended. One/zero for extended/standard format frame.
bits : 21 - 21 (1 bit)
access : read-write
SRR : Substitute Remote Request. Contains a fixed recessive bit.
bits : 22 - 22 (1 bit)
access : read-write
RESERVED : Reserved
bits : 23 - 23 (1 bit)
access : read-only
CODE : Reserved
bits : 24 - 27 (4 bit)
access : read-write
RESERVED : Reserved
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : Reserved
bits : 29 - 29 (1 bit)
access : read-only
RESERVED : Reserved
bits : 30 - 30 (1 bit)
access : read-only
RESERVED : Reserved
bits : 31 - 31 (1 bit)
access : read-only
Rx Individual Mask Registers
address_offset : 0x220C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MI : Individual Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Rx Individual Mask Registers
address_offset : 0x22228 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MI : Individual Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Message Buffer 26 ID Register
address_offset : 0x224 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXT : Contains extended (LOW word) identifier of message buffer.
bits : 0 - 17 (18 bit)
access : read-write
STD : Contains standard/extended (HIGH word) identifier of message buffer.
bits : 18 - 28 (11 bit)
access : read-write
PRIO : Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority.
bits : 29 - 31 (3 bit)
access : read-write
Message Buffer 26 WORD0 Register
address_offset : 0x228 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_3 : Data byte 3 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_2 : Data byte 2 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_1 : Data byte 1 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_0 : Data byte 0 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Rx Individual Mask Registers
address_offset : 0x22B98 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MI : Individual Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Message Buffer 26 WORD1 Register
address_offset : 0x22C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_7 : Data byte 7 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_6 : Data byte 6 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_5 : Data byte 5 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_4 : Data byte 4 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 27 CS Register
address_offset : 0x230 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TIME_STAMP : Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer, captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus.
bits : 0 - 15 (16 bit)
access : read-write
DLC : Length of the data to be stored/transmitted.
bits : 16 - 19 (4 bit)
access : read-write
RTR : Remote Transmission Request. One/zero for remote/data frame.
bits : 20 - 20 (1 bit)
access : read-write
IDE : ID Extended. One/zero for extended/standard format frame.
bits : 21 - 21 (1 bit)
access : read-write
SRR : Substitute Remote Request. Contains a fixed recessive bit.
bits : 22 - 22 (1 bit)
access : read-write
RESERVED : Reserved
bits : 23 - 23 (1 bit)
access : read-only
CODE : Reserved
bits : 24 - 27 (4 bit)
access : read-write
RESERVED : Reserved
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : Reserved
bits : 29 - 29 (1 bit)
access : read-only
RESERVED : Reserved
bits : 30 - 30 (1 bit)
access : read-only
RESERVED : Reserved
bits : 31 - 31 (1 bit)
access : read-only
Message Buffer 27 ID Register
address_offset : 0x234 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXT : Contains extended (LOW word) identifier of message buffer.
bits : 0 - 17 (18 bit)
access : read-write
STD : Contains standard/extended (HIGH word) identifier of message buffer.
bits : 18 - 28 (11 bit)
access : read-write
PRIO : Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority.
bits : 29 - 31 (3 bit)
access : read-write
Rx Individual Mask Registers
address_offset : 0x2350C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MI : Individual Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Message Buffer 27 WORD0 Register
address_offset : 0x238 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_3 : Data byte 3 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_2 : Data byte 2 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_1 : Data byte 1 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_0 : Data byte 0 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 27 WORD1 Register
address_offset : 0x23C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_7 : Data byte 7 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_6 : Data byte 6 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_5 : Data byte 5 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_4 : Data byte 4 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Rx Individual Mask Registers
address_offset : 0x23E84 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MI : Individual Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Interrupt Masks 2 register
address_offset : 0x24 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
BUFHM : Buffer MB i Mask
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding buffer Interrupt is disabled.
#1 : 1
The corresponding buffer Interrupt is enabled.
End of enumeration elements list.
Message Buffer 28 CS Register
address_offset : 0x240 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TIME_STAMP : Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer, captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus.
bits : 0 - 15 (16 bit)
access : read-write
DLC : Length of the data to be stored/transmitted.
bits : 16 - 19 (4 bit)
access : read-write
RTR : Remote Transmission Request. One/zero for remote/data frame.
bits : 20 - 20 (1 bit)
access : read-write
IDE : ID Extended. One/zero for extended/standard format frame.
bits : 21 - 21 (1 bit)
access : read-write
SRR : Substitute Remote Request. Contains a fixed recessive bit.
bits : 22 - 22 (1 bit)
access : read-write
RESERVED : Reserved
bits : 23 - 23 (1 bit)
access : read-only
CODE : Reserved
bits : 24 - 27 (4 bit)
access : read-write
RESERVED : Reserved
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : Reserved
bits : 29 - 29 (1 bit)
access : read-only
RESERVED : Reserved
bits : 30 - 30 (1 bit)
access : read-only
RESERVED : Reserved
bits : 31 - 31 (1 bit)
access : read-only
Message Buffer 28 ID Register
address_offset : 0x244 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXT : Contains extended (LOW word) identifier of message buffer.
bits : 0 - 17 (18 bit)
access : read-write
STD : Contains standard/extended (HIGH word) identifier of message buffer.
bits : 18 - 28 (11 bit)
access : read-write
PRIO : Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority.
bits : 29 - 31 (3 bit)
access : read-write
Message Buffer 28 WORD0 Register
address_offset : 0x248 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_3 : Data byte 3 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_2 : Data byte 2 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_1 : Data byte 1 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_0 : Data byte 0 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Rx Individual Mask Registers
address_offset : 0x24800 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MI : Individual Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Message Buffer 28 WORD1 Register
address_offset : 0x24C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_7 : Data byte 7 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_6 : Data byte 6 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_5 : Data byte 5 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_4 : Data byte 4 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 29 CS Register
address_offset : 0x250 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TIME_STAMP : Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer, captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus.
bits : 0 - 15 (16 bit)
access : read-write
DLC : Length of the data to be stored/transmitted.
bits : 16 - 19 (4 bit)
access : read-write
RTR : Remote Transmission Request. One/zero for remote/data frame.
bits : 20 - 20 (1 bit)
access : read-write
IDE : ID Extended. One/zero for extended/standard format frame.
bits : 21 - 21 (1 bit)
access : read-write
SRR : Substitute Remote Request. Contains a fixed recessive bit.
bits : 22 - 22 (1 bit)
access : read-write
RESERVED : Reserved
bits : 23 - 23 (1 bit)
access : read-only
CODE : Reserved
bits : 24 - 27 (4 bit)
access : read-write
RESERVED : Reserved
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : Reserved
bits : 29 - 29 (1 bit)
access : read-only
RESERVED : Reserved
bits : 30 - 30 (1 bit)
access : read-only
RESERVED : Reserved
bits : 31 - 31 (1 bit)
access : read-only
Message Buffer 29 ID Register
address_offset : 0x254 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXT : Contains extended (LOW word) identifier of message buffer.
bits : 0 - 17 (18 bit)
access : read-write
STD : Contains standard/extended (HIGH word) identifier of message buffer.
bits : 18 - 28 (11 bit)
access : read-write
PRIO : Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority.
bits : 29 - 31 (3 bit)
access : read-write
Message Buffer 29 WORD0 Register
address_offset : 0x258 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_3 : Data byte 3 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_2 : Data byte 2 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_1 : Data byte 1 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_0 : Data byte 0 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 29 WORD1 Register
address_offset : 0x25C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_7 : Data byte 7 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_6 : Data byte 6 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_5 : Data byte 5 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_4 : Data byte 4 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 30 CS Register
address_offset : 0x260 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TIME_STAMP : Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer, captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus.
bits : 0 - 15 (16 bit)
access : read-write
DLC : Length of the data to be stored/transmitted.
bits : 16 - 19 (4 bit)
access : read-write
RTR : Remote Transmission Request. One/zero for remote/data frame.
bits : 20 - 20 (1 bit)
access : read-write
IDE : ID Extended. One/zero for extended/standard format frame.
bits : 21 - 21 (1 bit)
access : read-write
SRR : Substitute Remote Request. Contains a fixed recessive bit.
bits : 22 - 22 (1 bit)
access : read-write
RESERVED : Reserved
bits : 23 - 23 (1 bit)
access : read-only
CODE : Reserved
bits : 24 - 27 (4 bit)
access : read-write
RESERVED : Reserved
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : Reserved
bits : 29 - 29 (1 bit)
access : read-only
RESERVED : Reserved
bits : 30 - 30 (1 bit)
access : read-only
RESERVED : Reserved
bits : 31 - 31 (1 bit)
access : read-only
Message Buffer 30 ID Register
address_offset : 0x264 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXT : Contains extended (LOW word) identifier of message buffer.
bits : 0 - 17 (18 bit)
access : read-write
STD : Contains standard/extended (HIGH word) identifier of message buffer.
bits : 18 - 28 (11 bit)
access : read-write
PRIO : Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority.
bits : 29 - 31 (3 bit)
access : read-write
Message Buffer 30 WORD0 Register
address_offset : 0x268 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_3 : Data byte 3 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_2 : Data byte 2 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_1 : Data byte 1 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_0 : Data byte 0 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 30 WORD1 Register
address_offset : 0x26C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_7 : Data byte 7 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_6 : Data byte 6 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_5 : Data byte 5 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_4 : Data byte 4 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 31 CS Register
address_offset : 0x270 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TIME_STAMP : Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer, captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus.
bits : 0 - 15 (16 bit)
access : read-write
DLC : Length of the data to be stored/transmitted.
bits : 16 - 19 (4 bit)
access : read-write
RTR : Remote Transmission Request. One/zero for remote/data frame.
bits : 20 - 20 (1 bit)
access : read-write
IDE : ID Extended. One/zero for extended/standard format frame.
bits : 21 - 21 (1 bit)
access : read-write
SRR : Substitute Remote Request. Contains a fixed recessive bit.
bits : 22 - 22 (1 bit)
access : read-write
RESERVED : Reserved
bits : 23 - 23 (1 bit)
access : read-only
CODE : Reserved
bits : 24 - 27 (4 bit)
access : read-write
RESERVED : Reserved
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : Reserved
bits : 29 - 29 (1 bit)
access : read-only
RESERVED : Reserved
bits : 30 - 30 (1 bit)
access : read-only
RESERVED : Reserved
bits : 31 - 31 (1 bit)
access : read-only
Message Buffer 31 ID Register
address_offset : 0x274 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXT : Contains extended (LOW word) identifier of message buffer.
bits : 0 - 17 (18 bit)
access : read-write
STD : Contains standard/extended (HIGH word) identifier of message buffer.
bits : 18 - 28 (11 bit)
access : read-write
PRIO : Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority.
bits : 29 - 31 (3 bit)
access : read-write
Message Buffer 31 WORD0 Register
address_offset : 0x278 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_3 : Data byte 3 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_2 : Data byte 2 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_1 : Data byte 1 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_0 : Data byte 0 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 31 WORD1 Register
address_offset : 0x27C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_7 : Data byte 7 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_6 : Data byte 6 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_5 : Data byte 5 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_4 : Data byte 4 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Interrupt Masks 1 register
address_offset : 0x28 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
BUFLM : Buffer MB i Mask
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding buffer Interrupt is disabled.
#1 : 1
The corresponding buffer Interrupt is enabled.
End of enumeration elements list.
Message Buffer 32 CS Register
address_offset : 0x280 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TIME_STAMP : Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer, captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus.
bits : 0 - 15 (16 bit)
access : read-write
DLC : Length of the data to be stored/transmitted.
bits : 16 - 19 (4 bit)
access : read-write
RTR : Remote Transmission Request. One/zero for remote/data frame.
bits : 20 - 20 (1 bit)
access : read-write
IDE : ID Extended. One/zero for extended/standard format frame.
bits : 21 - 21 (1 bit)
access : read-write
SRR : Substitute Remote Request. Contains a fixed recessive bit.
bits : 22 - 22 (1 bit)
access : read-write
RESERVED : Reserved
bits : 23 - 23 (1 bit)
access : read-only
CODE : Reserved
bits : 24 - 27 (4 bit)
access : read-write
RESERVED : Reserved
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : Reserved
bits : 29 - 29 (1 bit)
access : read-only
RESERVED : Reserved
bits : 30 - 30 (1 bit)
access : read-only
RESERVED : Reserved
bits : 31 - 31 (1 bit)
access : read-only
Message Buffer 32 ID Register
address_offset : 0x284 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXT : Contains extended (LOW word) identifier of message buffer.
bits : 0 - 17 (18 bit)
access : read-write
STD : Contains standard/extended (HIGH word) identifier of message buffer.
bits : 18 - 28 (11 bit)
access : read-write
PRIO : Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority.
bits : 29 - 31 (3 bit)
access : read-write
Message Buffer 32 WORD0 Register
address_offset : 0x288 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_3 : Data byte 3 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_2 : Data byte 2 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_1 : Data byte 1 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_0 : Data byte 0 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 32 WORD1 Register
address_offset : 0x28C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_7 : Data byte 7 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_6 : Data byte 6 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_5 : Data byte 5 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_4 : Data byte 4 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 33 CS Register
address_offset : 0x290 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TIME_STAMP : Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer, captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus.
bits : 0 - 15 (16 bit)
access : read-write
DLC : Length of the data to be stored/transmitted.
bits : 16 - 19 (4 bit)
access : read-write
RTR : Remote Transmission Request. One/zero for remote/data frame.
bits : 20 - 20 (1 bit)
access : read-write
IDE : ID Extended. One/zero for extended/standard format frame.
bits : 21 - 21 (1 bit)
access : read-write
SRR : Substitute Remote Request. Contains a fixed recessive bit.
bits : 22 - 22 (1 bit)
access : read-write
RESERVED : Reserved
bits : 23 - 23 (1 bit)
access : read-only
CODE : Reserved
bits : 24 - 27 (4 bit)
access : read-write
RESERVED : Reserved
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : Reserved
bits : 29 - 29 (1 bit)
access : read-only
RESERVED : Reserved
bits : 30 - 30 (1 bit)
access : read-only
RESERVED : Reserved
bits : 31 - 31 (1 bit)
access : read-only
Message Buffer 33 ID Register
address_offset : 0x294 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXT : Contains extended (LOW word) identifier of message buffer.
bits : 0 - 17 (18 bit)
access : read-write
STD : Contains standard/extended (HIGH word) identifier of message buffer.
bits : 18 - 28 (11 bit)
access : read-write
PRIO : Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority.
bits : 29 - 31 (3 bit)
access : read-write
Message Buffer 33 WORD0 Register
address_offset : 0x298 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_3 : Data byte 3 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_2 : Data byte 2 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_1 : Data byte 1 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_0 : Data byte 0 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 33 WORD1 Register
address_offset : 0x29C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_7 : Data byte 7 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_6 : Data byte 6 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_5 : Data byte 5 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_4 : Data byte 4 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 34 CS Register
address_offset : 0x2A0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TIME_STAMP : Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer, captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus.
bits : 0 - 15 (16 bit)
access : read-write
DLC : Length of the data to be stored/transmitted.
bits : 16 - 19 (4 bit)
access : read-write
RTR : Remote Transmission Request. One/zero for remote/data frame.
bits : 20 - 20 (1 bit)
access : read-write
IDE : ID Extended. One/zero for extended/standard format frame.
bits : 21 - 21 (1 bit)
access : read-write
SRR : Substitute Remote Request. Contains a fixed recessive bit.
bits : 22 - 22 (1 bit)
access : read-write
RESERVED : Reserved
bits : 23 - 23 (1 bit)
access : read-only
CODE : Reserved
bits : 24 - 27 (4 bit)
access : read-write
RESERVED : Reserved
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : Reserved
bits : 29 - 29 (1 bit)
access : read-only
RESERVED : Reserved
bits : 30 - 30 (1 bit)
access : read-only
RESERVED : Reserved
bits : 31 - 31 (1 bit)
access : read-only
Message Buffer 34 ID Register
address_offset : 0x2A4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXT : Contains extended (LOW word) identifier of message buffer.
bits : 0 - 17 (18 bit)
access : read-write
STD : Contains standard/extended (HIGH word) identifier of message buffer.
bits : 18 - 28 (11 bit)
access : read-write
PRIO : Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority.
bits : 29 - 31 (3 bit)
access : read-write
Message Buffer 34 WORD0 Register
address_offset : 0x2A8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_3 : Data byte 3 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_2 : Data byte 2 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_1 : Data byte 1 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_0 : Data byte 0 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Rx Individual Mask Registers
address_offset : 0x2A98 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MI : Individual Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Message Buffer 34 WORD1 Register
address_offset : 0x2AC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_7 : Data byte 7 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_6 : Data byte 6 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_5 : Data byte 5 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_4 : Data byte 4 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 35 CS Register
address_offset : 0x2B0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TIME_STAMP : Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer, captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus.
bits : 0 - 15 (16 bit)
access : read-write
DLC : Length of the data to be stored/transmitted.
bits : 16 - 19 (4 bit)
access : read-write
RTR : Remote Transmission Request. One/zero for remote/data frame.
bits : 20 - 20 (1 bit)
access : read-write
IDE : ID Extended. One/zero for extended/standard format frame.
bits : 21 - 21 (1 bit)
access : read-write
SRR : Substitute Remote Request. Contains a fixed recessive bit.
bits : 22 - 22 (1 bit)
access : read-write
RESERVED : Reserved
bits : 23 - 23 (1 bit)
access : read-only
CODE : Reserved
bits : 24 - 27 (4 bit)
access : read-write
RESERVED : Reserved
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : Reserved
bits : 29 - 29 (1 bit)
access : read-only
RESERVED : Reserved
bits : 30 - 30 (1 bit)
access : read-only
RESERVED : Reserved
bits : 31 - 31 (1 bit)
access : read-only
Message Buffer 35 ID Register
address_offset : 0x2B4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXT : Contains extended (LOW word) identifier of message buffer.
bits : 0 - 17 (18 bit)
access : read-write
STD : Contains standard/extended (HIGH word) identifier of message buffer.
bits : 18 - 28 (11 bit)
access : read-write
PRIO : Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority.
bits : 29 - 31 (3 bit)
access : read-write
Message Buffer 35 WORD0 Register
address_offset : 0x2B8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_3 : Data byte 3 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_2 : Data byte 2 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_1 : Data byte 1 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_0 : Data byte 0 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 35 WORD1 Register
address_offset : 0x2BC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_7 : Data byte 7 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_6 : Data byte 6 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_5 : Data byte 5 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_4 : Data byte 4 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Interrupt Flags 2 register
address_offset : 0x2C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
BUFHI : Buffer MB i Interrupt
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding buffer has no occurrence of successfully completed transmission or reception.
#1 : 1
The corresponding buffer has successfully completed transmission or reception.
End of enumeration elements list.
Message Buffer 36 CS Register
address_offset : 0x2C0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TIME_STAMP : Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer, captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus.
bits : 0 - 15 (16 bit)
access : read-write
DLC : Length of the data to be stored/transmitted.
bits : 16 - 19 (4 bit)
access : read-write
RTR : Remote Transmission Request. One/zero for remote/data frame.
bits : 20 - 20 (1 bit)
access : read-write
IDE : ID Extended. One/zero for extended/standard format frame.
bits : 21 - 21 (1 bit)
access : read-write
SRR : Substitute Remote Request. Contains a fixed recessive bit.
bits : 22 - 22 (1 bit)
access : read-write
RESERVED : Reserved
bits : 23 - 23 (1 bit)
access : read-only
CODE : Reserved
bits : 24 - 27 (4 bit)
access : read-write
RESERVED : Reserved
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : Reserved
bits : 29 - 29 (1 bit)
access : read-only
RESERVED : Reserved
bits : 30 - 30 (1 bit)
access : read-only
RESERVED : Reserved
bits : 31 - 31 (1 bit)
access : read-only
Message Buffer 36 ID Register
address_offset : 0x2C4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXT : Contains extended (LOW word) identifier of message buffer.
bits : 0 - 17 (18 bit)
access : read-write
STD : Contains standard/extended (HIGH word) identifier of message buffer.
bits : 18 - 28 (11 bit)
access : read-write
PRIO : Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority.
bits : 29 - 31 (3 bit)
access : read-write
Message Buffer 36 WORD0 Register
address_offset : 0x2C8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_3 : Data byte 3 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_2 : Data byte 2 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_1 : Data byte 1 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_0 : Data byte 0 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 36 WORD1 Register
address_offset : 0x2CC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_7 : Data byte 7 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_6 : Data byte 6 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_5 : Data byte 5 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_4 : Data byte 4 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 37 CS Register
address_offset : 0x2D0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TIME_STAMP : Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer, captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus.
bits : 0 - 15 (16 bit)
access : read-write
DLC : Length of the data to be stored/transmitted.
bits : 16 - 19 (4 bit)
access : read-write
RTR : Remote Transmission Request. One/zero for remote/data frame.
bits : 20 - 20 (1 bit)
access : read-write
IDE : ID Extended. One/zero for extended/standard format frame.
bits : 21 - 21 (1 bit)
access : read-write
SRR : Substitute Remote Request. Contains a fixed recessive bit.
bits : 22 - 22 (1 bit)
access : read-write
RESERVED : Reserved
bits : 23 - 23 (1 bit)
access : read-only
CODE : Reserved
bits : 24 - 27 (4 bit)
access : read-write
RESERVED : Reserved
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : Reserved
bits : 29 - 29 (1 bit)
access : read-only
RESERVED : Reserved
bits : 30 - 30 (1 bit)
access : read-only
RESERVED : Reserved
bits : 31 - 31 (1 bit)
access : read-only
Message Buffer 37 ID Register
address_offset : 0x2D4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXT : Contains extended (LOW word) identifier of message buffer.
bits : 0 - 17 (18 bit)
access : read-write
STD : Contains standard/extended (HIGH word) identifier of message buffer.
bits : 18 - 28 (11 bit)
access : read-write
PRIO : Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority.
bits : 29 - 31 (3 bit)
access : read-write
Message Buffer 37 WORD0 Register
address_offset : 0x2D8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_3 : Data byte 3 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_2 : Data byte 2 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_1 : Data byte 1 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_0 : Data byte 0 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 37 WORD1 Register
address_offset : 0x2DC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_7 : Data byte 7 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_6 : Data byte 6 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_5 : Data byte 5 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_4 : Data byte 4 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 38 CS Register
address_offset : 0x2E0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TIME_STAMP : Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer, captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus.
bits : 0 - 15 (16 bit)
access : read-write
DLC : Length of the data to be stored/transmitted.
bits : 16 - 19 (4 bit)
access : read-write
RTR : Remote Transmission Request. One/zero for remote/data frame.
bits : 20 - 20 (1 bit)
access : read-write
IDE : ID Extended. One/zero for extended/standard format frame.
bits : 21 - 21 (1 bit)
access : read-write
SRR : Substitute Remote Request. Contains a fixed recessive bit.
bits : 22 - 22 (1 bit)
access : read-write
RESERVED : Reserved
bits : 23 - 23 (1 bit)
access : read-only
CODE : Reserved
bits : 24 - 27 (4 bit)
access : read-write
RESERVED : Reserved
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : Reserved
bits : 29 - 29 (1 bit)
access : read-only
RESERVED : Reserved
bits : 30 - 30 (1 bit)
access : read-only
RESERVED : Reserved
bits : 31 - 31 (1 bit)
access : read-only
Message Buffer 38 ID Register
address_offset : 0x2E4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXT : Contains extended (LOW word) identifier of message buffer.
bits : 0 - 17 (18 bit)
access : read-write
STD : Contains standard/extended (HIGH word) identifier of message buffer.
bits : 18 - 28 (11 bit)
access : read-write
PRIO : Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority.
bits : 29 - 31 (3 bit)
access : read-write
Message Buffer 38 WORD0 Register
address_offset : 0x2E8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_3 : Data byte 3 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_2 : Data byte 2 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_1 : Data byte 1 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_0 : Data byte 0 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 38 WORD1 Register
address_offset : 0x2EC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_7 : Data byte 7 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_6 : Data byte 6 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_5 : Data byte 5 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_4 : Data byte 4 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 39 CS Register
address_offset : 0x2F0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TIME_STAMP : Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer, captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus.
bits : 0 - 15 (16 bit)
access : read-write
DLC : Length of the data to be stored/transmitted.
bits : 16 - 19 (4 bit)
access : read-write
RTR : Remote Transmission Request. One/zero for remote/data frame.
bits : 20 - 20 (1 bit)
access : read-write
IDE : ID Extended. One/zero for extended/standard format frame.
bits : 21 - 21 (1 bit)
access : read-write
SRR : Substitute Remote Request. Contains a fixed recessive bit.
bits : 22 - 22 (1 bit)
access : read-write
RESERVED : Reserved
bits : 23 - 23 (1 bit)
access : read-only
CODE : Reserved
bits : 24 - 27 (4 bit)
access : read-write
RESERVED : Reserved
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : Reserved
bits : 29 - 29 (1 bit)
access : read-only
RESERVED : Reserved
bits : 30 - 30 (1 bit)
access : read-only
RESERVED : Reserved
bits : 31 - 31 (1 bit)
access : read-only
Message Buffer 39 ID Register
address_offset : 0x2F4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXT : Contains extended (LOW word) identifier of message buffer.
bits : 0 - 17 (18 bit)
access : read-write
STD : Contains standard/extended (HIGH word) identifier of message buffer.
bits : 18 - 28 (11 bit)
access : read-write
PRIO : Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority.
bits : 29 - 31 (3 bit)
access : read-write
Message Buffer 39 WORD0 Register
address_offset : 0x2F8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_3 : Data byte 3 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_2 : Data byte 2 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_1 : Data byte 1 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_0 : Data byte 0 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 39 WORD1 Register
address_offset : 0x2FC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_7 : Data byte 7 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_6 : Data byte 6 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_5 : Data byte 5 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_4 : Data byte 4 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Interrupt Flags 1 register
address_offset : 0x30 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
BUF0I : Buffer MB0 Interrupt Or "reserved"
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding buffer has no occurrence of successfully completed transmission or reception when MCR[RFEN]=0.
#1 : 1
The corresponding buffer has successfully completed transmission or reception when MCR[RFEN]=0.
End of enumeration elements list.
BUF4TO1I : Buffer MB i Interrupt Or "reserved"
bits : 1 - 4 (4 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding buffer has no occurrence of successfully completed transmission or reception when MCR[RFEN]=0.
#1 : 1
The corresponding buffer has successfully completed transmission or reception when MCR[RFEN]=0.
End of enumeration elements list.
BUF5I : Buffer MB5 Interrupt Or "Frames available in Rx FIFO"
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
No occurrence of MB5 completing transmission/reception when MCR[RFEN]=0, or of frame(s) available in the FIFO, when MCR[RFEN]=1
#1 : 1
MB5 completed transmission/reception when MCR[RFEN]=0, or frame(s) available in the Rx FIFO when MCR[RFEN]=1
End of enumeration elements list.
BUF6I : Buffer MB6 Interrupt Or "Rx FIFO Warning"
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
No occurrence of MB6 completing transmission/reception when MCR[RFEN]=0, or of Rx FIFO almost full when MCR[RFEN]=1
#1 : 1
MB6 completed transmission/reception when MCR[RFEN]=0, or Rx FIFO almost full when MCR[RFEN]=1
End of enumeration elements list.
BUF7I : Buffer MB7 Interrupt Or "Rx FIFO Overflow"
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
No occurrence of MB7 completing transmission/reception when MCR[RFEN]=0, or of Rx FIFO overflow when MCR[RFEN]=1
#1 : 1
MB7 completed transmission/reception when MCR[RFEN]=0, or Rx FIFO overflow when MCR[RFEN]=1
End of enumeration elements list.
BUF31TO8I : Buffer MBi Interrupt
bits : 8 - 31 (24 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding buffer has no occurrence of successfully completed transmission or reception.
#1 : 1
The corresponding buffer has successfully completed transmission or reception.
End of enumeration elements list.
Message Buffer 40 CS Register
address_offset : 0x300 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TIME_STAMP : Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer, captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus.
bits : 0 - 15 (16 bit)
access : read-write
DLC : Length of the data to be stored/transmitted.
bits : 16 - 19 (4 bit)
access : read-write
RTR : Remote Transmission Request. One/zero for remote/data frame.
bits : 20 - 20 (1 bit)
access : read-write
IDE : ID Extended. One/zero for extended/standard format frame.
bits : 21 - 21 (1 bit)
access : read-write
SRR : Substitute Remote Request. Contains a fixed recessive bit.
bits : 22 - 22 (1 bit)
access : read-write
RESERVED : Reserved
bits : 23 - 23 (1 bit)
access : read-only
CODE : Reserved
bits : 24 - 27 (4 bit)
access : read-write
RESERVED : Reserved
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : Reserved
bits : 29 - 29 (1 bit)
access : read-only
RESERVED : Reserved
bits : 30 - 30 (1 bit)
access : read-only
RESERVED : Reserved
bits : 31 - 31 (1 bit)
access : read-only
Message Buffer 40 ID Register
address_offset : 0x304 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXT : Contains extended (LOW word) identifier of message buffer.
bits : 0 - 17 (18 bit)
access : read-write
STD : Contains standard/extended (HIGH word) identifier of message buffer.
bits : 18 - 28 (11 bit)
access : read-write
PRIO : Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority.
bits : 29 - 31 (3 bit)
access : read-write
Message Buffer 40 WORD0 Register
address_offset : 0x308 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_3 : Data byte 3 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_2 : Data byte 2 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_1 : Data byte 1 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_0 : Data byte 0 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 40 WORD1 Register
address_offset : 0x30C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_7 : Data byte 7 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_6 : Data byte 6 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_5 : Data byte 5 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_4 : Data byte 4 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 41 CS Register
address_offset : 0x310 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TIME_STAMP : Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer, captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus.
bits : 0 - 15 (16 bit)
access : read-write
DLC : Length of the data to be stored/transmitted.
bits : 16 - 19 (4 bit)
access : read-write
RTR : Remote Transmission Request. One/zero for remote/data frame.
bits : 20 - 20 (1 bit)
access : read-write
IDE : ID Extended. One/zero for extended/standard format frame.
bits : 21 - 21 (1 bit)
access : read-write
SRR : Substitute Remote Request. Contains a fixed recessive bit.
bits : 22 - 22 (1 bit)
access : read-write
RESERVED : Reserved
bits : 23 - 23 (1 bit)
access : read-only
CODE : Reserved
bits : 24 - 27 (4 bit)
access : read-write
RESERVED : Reserved
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : Reserved
bits : 29 - 29 (1 bit)
access : read-only
RESERVED : Reserved
bits : 30 - 30 (1 bit)
access : read-only
RESERVED : Reserved
bits : 31 - 31 (1 bit)
access : read-only
Message Buffer 41 ID Register
address_offset : 0x314 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXT : Contains extended (LOW word) identifier of message buffer.
bits : 0 - 17 (18 bit)
access : read-write
STD : Contains standard/extended (HIGH word) identifier of message buffer.
bits : 18 - 28 (11 bit)
access : read-write
PRIO : Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority.
bits : 29 - 31 (3 bit)
access : read-write
Message Buffer 41 WORD0 Register
address_offset : 0x318 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_3 : Data byte 3 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_2 : Data byte 2 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_1 : Data byte 1 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_0 : Data byte 0 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 41 WORD1 Register
address_offset : 0x31C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_7 : Data byte 7 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_6 : Data byte 6 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_5 : Data byte 5 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_4 : Data byte 4 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 42 CS Register
address_offset : 0x320 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TIME_STAMP : Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer, captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus.
bits : 0 - 15 (16 bit)
access : read-write
DLC : Length of the data to be stored/transmitted.
bits : 16 - 19 (4 bit)
access : read-write
RTR : Remote Transmission Request. One/zero for remote/data frame.
bits : 20 - 20 (1 bit)
access : read-write
IDE : ID Extended. One/zero for extended/standard format frame.
bits : 21 - 21 (1 bit)
access : read-write
SRR : Substitute Remote Request. Contains a fixed recessive bit.
bits : 22 - 22 (1 bit)
access : read-write
RESERVED : Reserved
bits : 23 - 23 (1 bit)
access : read-only
CODE : Reserved
bits : 24 - 27 (4 bit)
access : read-write
RESERVED : Reserved
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : Reserved
bits : 29 - 29 (1 bit)
access : read-only
RESERVED : Reserved
bits : 30 - 30 (1 bit)
access : read-only
RESERVED : Reserved
bits : 31 - 31 (1 bit)
access : read-only
Message Buffer 42 ID Register
address_offset : 0x324 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXT : Contains extended (LOW word) identifier of message buffer.
bits : 0 - 17 (18 bit)
access : read-write
STD : Contains standard/extended (HIGH word) identifier of message buffer.
bits : 18 - 28 (11 bit)
access : read-write
PRIO : Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority.
bits : 29 - 31 (3 bit)
access : read-write
Message Buffer 42 WORD0 Register
address_offset : 0x328 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_3 : Data byte 3 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_2 : Data byte 2 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_1 : Data byte 1 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_0 : Data byte 0 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 42 WORD1 Register
address_offset : 0x32C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_7 : Data byte 7 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_6 : Data byte 6 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_5 : Data byte 5 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_4 : Data byte 4 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 43 CS Register
address_offset : 0x330 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TIME_STAMP : Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer, captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus.
bits : 0 - 15 (16 bit)
access : read-write
DLC : Length of the data to be stored/transmitted.
bits : 16 - 19 (4 bit)
access : read-write
RTR : Remote Transmission Request. One/zero for remote/data frame.
bits : 20 - 20 (1 bit)
access : read-write
IDE : ID Extended. One/zero for extended/standard format frame.
bits : 21 - 21 (1 bit)
access : read-write
SRR : Substitute Remote Request. Contains a fixed recessive bit.
bits : 22 - 22 (1 bit)
access : read-write
RESERVED : Reserved
bits : 23 - 23 (1 bit)
access : read-only
CODE : Reserved
bits : 24 - 27 (4 bit)
access : read-write
RESERVED : Reserved
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : Reserved
bits : 29 - 29 (1 bit)
access : read-only
RESERVED : Reserved
bits : 30 - 30 (1 bit)
access : read-only
RESERVED : Reserved
bits : 31 - 31 (1 bit)
access : read-only
Rx Individual Mask Registers
address_offset : 0x3328 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MI : Individual Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Message Buffer 43 ID Register
address_offset : 0x334 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXT : Contains extended (LOW word) identifier of message buffer.
bits : 0 - 17 (18 bit)
access : read-write
STD : Contains standard/extended (HIGH word) identifier of message buffer.
bits : 18 - 28 (11 bit)
access : read-write
PRIO : Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority.
bits : 29 - 31 (3 bit)
access : read-write
Message Buffer 43 WORD0 Register
address_offset : 0x338 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_3 : Data byte 3 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_2 : Data byte 2 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_1 : Data byte 1 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_0 : Data byte 0 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 43 WORD1 Register
address_offset : 0x33C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_7 : Data byte 7 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_6 : Data byte 6 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_5 : Data byte 5 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_4 : Data byte 4 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Control 2 register
address_offset : 0x34 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RESERVED : no description available
bits : 0 - 15 (16 bit)
access : read-only
EACEN : Entire Frame Arbitration Field Comparison Enable For Rx Mailboxes
bits : 16 - 16 (1 bit)
access : read-write
Enumeration:
#0 : 0
Rx Mailbox filter's IDE bit is always compared and RTR is never compared despite mask bits.
#1 : 1
Enables the comparison of both Rx Mailbox filter's IDE and RTR bit with their corresponding bits within the incoming frame. Mask bits do apply.
End of enumeration elements list.
RRS : Remote Request Storing
bits : 17 - 17 (1 bit)
access : read-write
Enumeration:
#0 : 0
Remote Response Frame is generated.
#1 : 1
Remote Request Frame is stored.
End of enumeration elements list.
MRP : Mailboxes Reception Priority
bits : 18 - 18 (1 bit)
access : read-write
Enumeration:
#0 : 0
Matching starts from Rx FIFO and continues on Mailboxes.
#1 : 1
Matching starts from Mailboxes and continues on Rx FIFO.
End of enumeration elements list.
TASD : Tx Arbitration Start Delay
bits : 19 - 23 (5 bit)
access : read-write
RFFN : Number Of Rx FIFO Filters
bits : 24 - 27 (4 bit)
access : read-write
WRMFRZ : Write-Access To Memory In Freeze Mode
bits : 28 - 28 (1 bit)
access : read-write
Enumeration:
#0 : 0
Maintain the write access restrictions.
#1 : 1
Enable unrestricted write access to FlexCAN memory.
End of enumeration elements list.
ECRWRE : Error-correction Configuration Register Write Enable
bits : 29 - 29 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disable update.
#1 : 1
Enable update.
End of enumeration elements list.
RESERVED : no description available
bits : 30 - 31 (2 bit)
access : read-only
Message Buffer 44 CS Register
address_offset : 0x340 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TIME_STAMP : Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer, captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus.
bits : 0 - 15 (16 bit)
access : read-write
DLC : Length of the data to be stored/transmitted.
bits : 16 - 19 (4 bit)
access : read-write
RTR : Remote Transmission Request. One/zero for remote/data frame.
bits : 20 - 20 (1 bit)
access : read-write
IDE : ID Extended. One/zero for extended/standard format frame.
bits : 21 - 21 (1 bit)
access : read-write
SRR : Substitute Remote Request. Contains a fixed recessive bit.
bits : 22 - 22 (1 bit)
access : read-write
RESERVED : Reserved
bits : 23 - 23 (1 bit)
access : read-only
CODE : Reserved
bits : 24 - 27 (4 bit)
access : read-write
RESERVED : Reserved
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : Reserved
bits : 29 - 29 (1 bit)
access : read-only
RESERVED : Reserved
bits : 30 - 30 (1 bit)
access : read-only
RESERVED : Reserved
bits : 31 - 31 (1 bit)
access : read-only
Message Buffer 44 ID Register
address_offset : 0x344 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXT : Contains extended (LOW word) identifier of message buffer.
bits : 0 - 17 (18 bit)
access : read-write
STD : Contains standard/extended (HIGH word) identifier of message buffer.
bits : 18 - 28 (11 bit)
access : read-write
PRIO : Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority.
bits : 29 - 31 (3 bit)
access : read-write
Message Buffer 44 WORD0 Register
address_offset : 0x348 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_3 : Data byte 3 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_2 : Data byte 2 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_1 : Data byte 1 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_0 : Data byte 0 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 44 WORD1 Register
address_offset : 0x34C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_7 : Data byte 7 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_6 : Data byte 6 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_5 : Data byte 5 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_4 : Data byte 4 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 45 CS Register
address_offset : 0x350 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TIME_STAMP : Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer, captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus.
bits : 0 - 15 (16 bit)
access : read-write
DLC : Length of the data to be stored/transmitted.
bits : 16 - 19 (4 bit)
access : read-write
RTR : Remote Transmission Request. One/zero for remote/data frame.
bits : 20 - 20 (1 bit)
access : read-write
IDE : ID Extended. One/zero for extended/standard format frame.
bits : 21 - 21 (1 bit)
access : read-write
SRR : Substitute Remote Request. Contains a fixed recessive bit.
bits : 22 - 22 (1 bit)
access : read-write
RESERVED : Reserved
bits : 23 - 23 (1 bit)
access : read-only
CODE : Reserved
bits : 24 - 27 (4 bit)
access : read-write
RESERVED : Reserved
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : Reserved
bits : 29 - 29 (1 bit)
access : read-only
RESERVED : Reserved
bits : 30 - 30 (1 bit)
access : read-only
RESERVED : Reserved
bits : 31 - 31 (1 bit)
access : read-only
Message Buffer 45 ID Register
address_offset : 0x354 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXT : Contains extended (LOW word) identifier of message buffer.
bits : 0 - 17 (18 bit)
access : read-write
STD : Contains standard/extended (HIGH word) identifier of message buffer.
bits : 18 - 28 (11 bit)
access : read-write
PRIO : Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority.
bits : 29 - 31 (3 bit)
access : read-write
Message Buffer 45 WORD0 Register
address_offset : 0x358 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_3 : Data byte 3 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_2 : Data byte 2 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_1 : Data byte 1 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_0 : Data byte 0 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 45 WORD1 Register
address_offset : 0x35C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_7 : Data byte 7 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_6 : Data byte 6 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_5 : Data byte 5 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_4 : Data byte 4 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 46 CS Register
address_offset : 0x360 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TIME_STAMP : Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer, captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus.
bits : 0 - 15 (16 bit)
access : read-write
DLC : Length of the data to be stored/transmitted.
bits : 16 - 19 (4 bit)
access : read-write
RTR : Remote Transmission Request. One/zero for remote/data frame.
bits : 20 - 20 (1 bit)
access : read-write
IDE : ID Extended. One/zero for extended/standard format frame.
bits : 21 - 21 (1 bit)
access : read-write
SRR : Substitute Remote Request. Contains a fixed recessive bit.
bits : 22 - 22 (1 bit)
access : read-write
RESERVED : Reserved
bits : 23 - 23 (1 bit)
access : read-only
CODE : Reserved
bits : 24 - 27 (4 bit)
access : read-write
RESERVED : Reserved
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : Reserved
bits : 29 - 29 (1 bit)
access : read-only
RESERVED : Reserved
bits : 30 - 30 (1 bit)
access : read-only
RESERVED : Reserved
bits : 31 - 31 (1 bit)
access : read-only
Message Buffer 46 ID Register
address_offset : 0x364 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXT : Contains extended (LOW word) identifier of message buffer.
bits : 0 - 17 (18 bit)
access : read-write
STD : Contains standard/extended (HIGH word) identifier of message buffer.
bits : 18 - 28 (11 bit)
access : read-write
PRIO : Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority.
bits : 29 - 31 (3 bit)
access : read-write
Message Buffer 46 WORD0 Register
address_offset : 0x368 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_3 : Data byte 3 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_2 : Data byte 2 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_1 : Data byte 1 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_0 : Data byte 0 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 46 WORD1 Register
address_offset : 0x36C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_7 : Data byte 7 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_6 : Data byte 6 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_5 : Data byte 5 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_4 : Data byte 4 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 47 CS Register
address_offset : 0x370 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TIME_STAMP : Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer, captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus.
bits : 0 - 15 (16 bit)
access : read-write
DLC : Length of the data to be stored/transmitted.
bits : 16 - 19 (4 bit)
access : read-write
RTR : Remote Transmission Request. One/zero for remote/data frame.
bits : 20 - 20 (1 bit)
access : read-write
IDE : ID Extended. One/zero for extended/standard format frame.
bits : 21 - 21 (1 bit)
access : read-write
SRR : Substitute Remote Request. Contains a fixed recessive bit.
bits : 22 - 22 (1 bit)
access : read-write
RESERVED : Reserved
bits : 23 - 23 (1 bit)
access : read-only
CODE : Reserved
bits : 24 - 27 (4 bit)
access : read-write
RESERVED : Reserved
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : Reserved
bits : 29 - 29 (1 bit)
access : read-only
RESERVED : Reserved
bits : 30 - 30 (1 bit)
access : read-only
RESERVED : Reserved
bits : 31 - 31 (1 bit)
access : read-only
Message Buffer 47 ID Register
address_offset : 0x374 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXT : Contains extended (LOW word) identifier of message buffer.
bits : 0 - 17 (18 bit)
access : read-write
STD : Contains standard/extended (HIGH word) identifier of message buffer.
bits : 18 - 28 (11 bit)
access : read-write
PRIO : Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority.
bits : 29 - 31 (3 bit)
access : read-write
Message Buffer 47 WORD0 Register
address_offset : 0x378 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_3 : Data byte 3 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_2 : Data byte 2 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_1 : Data byte 1 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_0 : Data byte 0 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 47 WORD1 Register
address_offset : 0x37C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_7 : Data byte 7 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_6 : Data byte 6 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_5 : Data byte 5 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_4 : Data byte 4 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Error and Status 2 register
address_offset : 0x38 Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
RESERVED : no description available
bits : 0 - 12 (13 bit)
access : read-only
IMB : Inactive Mailbox
bits : 13 - 13 (1 bit)
access : read-only
Enumeration:
#0 : 0
If ESR2[VPS] is asserted, the ESR2[LPTM] is not an inactive Mailbox.
#1 : 1
If ESR2[VPS] is asserted, there is at least one inactive Mailbox. LPTM content is the number of the first one.
End of enumeration elements list.
VPS : Valid Priority Status
bits : 14 - 14 (1 bit)
access : read-only
Enumeration:
#0 : 0
Contents of IMB and LPTM are invalid.
#1 : 1
Contents of IMB and LPTM are valid.
End of enumeration elements list.
RESERVED : no description available
bits : 15 - 15 (1 bit)
access : read-only
LPTM : Lowest Priority Tx Mailbox
bits : 16 - 22 (7 bit)
access : read-only
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-only
Message Buffer 48 CS Register
address_offset : 0x380 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TIME_STAMP : Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer, captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus.
bits : 0 - 15 (16 bit)
access : read-write
DLC : Length of the data to be stored/transmitted.
bits : 16 - 19 (4 bit)
access : read-write
RTR : Remote Transmission Request. One/zero for remote/data frame.
bits : 20 - 20 (1 bit)
access : read-write
IDE : ID Extended. One/zero for extended/standard format frame.
bits : 21 - 21 (1 bit)
access : read-write
SRR : Substitute Remote Request. Contains a fixed recessive bit.
bits : 22 - 22 (1 bit)
access : read-write
RESERVED : Reserved
bits : 23 - 23 (1 bit)
access : read-only
CODE : Reserved
bits : 24 - 27 (4 bit)
access : read-write
RESERVED : Reserved
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : Reserved
bits : 29 - 29 (1 bit)
access : read-only
RESERVED : Reserved
bits : 30 - 30 (1 bit)
access : read-only
RESERVED : Reserved
bits : 31 - 31 (1 bit)
access : read-only
Message Buffer 48 ID Register
address_offset : 0x384 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXT : Contains extended (LOW word) identifier of message buffer.
bits : 0 - 17 (18 bit)
access : read-write
STD : Contains standard/extended (HIGH word) identifier of message buffer.
bits : 18 - 28 (11 bit)
access : read-write
PRIO : Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority.
bits : 29 - 31 (3 bit)
access : read-write
Message Buffer 48 WORD0 Register
address_offset : 0x388 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_3 : Data byte 3 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_2 : Data byte 2 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_1 : Data byte 1 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_0 : Data byte 0 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 48 WORD1 Register
address_offset : 0x38C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_7 : Data byte 7 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_6 : Data byte 6 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_5 : Data byte 5 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_4 : Data byte 4 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 49 CS Register
address_offset : 0x390 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TIME_STAMP : Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer, captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus.
bits : 0 - 15 (16 bit)
access : read-write
DLC : Length of the data to be stored/transmitted.
bits : 16 - 19 (4 bit)
access : read-write
RTR : Remote Transmission Request. One/zero for remote/data frame.
bits : 20 - 20 (1 bit)
access : read-write
IDE : ID Extended. One/zero for extended/standard format frame.
bits : 21 - 21 (1 bit)
access : read-write
SRR : Substitute Remote Request. Contains a fixed recessive bit.
bits : 22 - 22 (1 bit)
access : read-write
RESERVED : Reserved
bits : 23 - 23 (1 bit)
access : read-only
CODE : Reserved
bits : 24 - 27 (4 bit)
access : read-write
RESERVED : Reserved
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : Reserved
bits : 29 - 29 (1 bit)
access : read-only
RESERVED : Reserved
bits : 30 - 30 (1 bit)
access : read-only
RESERVED : Reserved
bits : 31 - 31 (1 bit)
access : read-only
Message Buffer 49 ID Register
address_offset : 0x394 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXT : Contains extended (LOW word) identifier of message buffer.
bits : 0 - 17 (18 bit)
access : read-write
STD : Contains standard/extended (HIGH word) identifier of message buffer.
bits : 18 - 28 (11 bit)
access : read-write
PRIO : Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority.
bits : 29 - 31 (3 bit)
access : read-write
Message Buffer 49 WORD0 Register
address_offset : 0x398 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_3 : Data byte 3 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_2 : Data byte 2 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_1 : Data byte 1 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_0 : Data byte 0 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 49 WORD1 Register
address_offset : 0x39C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_7 : Data byte 7 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_6 : Data byte 6 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_5 : Data byte 5 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_4 : Data byte 4 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 50 CS Register
address_offset : 0x3A0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TIME_STAMP : Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer, captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus.
bits : 0 - 15 (16 bit)
access : read-write
DLC : Length of the data to be stored/transmitted.
bits : 16 - 19 (4 bit)
access : read-write
RTR : Remote Transmission Request. One/zero for remote/data frame.
bits : 20 - 20 (1 bit)
access : read-write
IDE : ID Extended. One/zero for extended/standard format frame.
bits : 21 - 21 (1 bit)
access : read-write
SRR : Substitute Remote Request. Contains a fixed recessive bit.
bits : 22 - 22 (1 bit)
access : read-write
RESERVED : Reserved
bits : 23 - 23 (1 bit)
access : read-only
CODE : Reserved
bits : 24 - 27 (4 bit)
access : read-write
RESERVED : Reserved
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : Reserved
bits : 29 - 29 (1 bit)
access : read-only
RESERVED : Reserved
bits : 30 - 30 (1 bit)
access : read-only
RESERVED : Reserved
bits : 31 - 31 (1 bit)
access : read-only
Message Buffer 50 ID Register
address_offset : 0x3A4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXT : Contains extended (LOW word) identifier of message buffer.
bits : 0 - 17 (18 bit)
access : read-write
STD : Contains standard/extended (HIGH word) identifier of message buffer.
bits : 18 - 28 (11 bit)
access : read-write
PRIO : Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority.
bits : 29 - 31 (3 bit)
access : read-write
Message Buffer 50 WORD0 Register
address_offset : 0x3A8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_3 : Data byte 3 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_2 : Data byte 2 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_1 : Data byte 1 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_0 : Data byte 0 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 50 WORD1 Register
address_offset : 0x3AC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_7 : Data byte 7 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_6 : Data byte 6 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_5 : Data byte 5 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_4 : Data byte 4 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 51 CS Register
address_offset : 0x3B0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TIME_STAMP : Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer, captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus.
bits : 0 - 15 (16 bit)
access : read-write
DLC : Length of the data to be stored/transmitted.
bits : 16 - 19 (4 bit)
access : read-write
RTR : Remote Transmission Request. One/zero for remote/data frame.
bits : 20 - 20 (1 bit)
access : read-write
IDE : ID Extended. One/zero for extended/standard format frame.
bits : 21 - 21 (1 bit)
access : read-write
SRR : Substitute Remote Request. Contains a fixed recessive bit.
bits : 22 - 22 (1 bit)
access : read-write
RESERVED : Reserved
bits : 23 - 23 (1 bit)
access : read-only
CODE : Reserved
bits : 24 - 27 (4 bit)
access : read-write
RESERVED : Reserved
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : Reserved
bits : 29 - 29 (1 bit)
access : read-only
RESERVED : Reserved
bits : 30 - 30 (1 bit)
access : read-only
RESERVED : Reserved
bits : 31 - 31 (1 bit)
access : read-only
Message Buffer 51 ID Register
address_offset : 0x3B4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXT : Contains extended (LOW word) identifier of message buffer.
bits : 0 - 17 (18 bit)
access : read-write
STD : Contains standard/extended (HIGH word) identifier of message buffer.
bits : 18 - 28 (11 bit)
access : read-write
PRIO : Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority.
bits : 29 - 31 (3 bit)
access : read-write
Message Buffer 51 WORD0 Register
address_offset : 0x3B8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_3 : Data byte 3 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_2 : Data byte 2 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_1 : Data byte 1 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_0 : Data byte 0 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Rx Individual Mask Registers
address_offset : 0x3BBC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MI : Individual Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Message Buffer 51 WORD1 Register
address_offset : 0x3BC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_7 : Data byte 7 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_6 : Data byte 6 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_5 : Data byte 5 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_4 : Data byte 4 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 52 CS Register
address_offset : 0x3C0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TIME_STAMP : Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer, captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus.
bits : 0 - 15 (16 bit)
access : read-write
DLC : Length of the data to be stored/transmitted.
bits : 16 - 19 (4 bit)
access : read-write
RTR : Remote Transmission Request. One/zero for remote/data frame.
bits : 20 - 20 (1 bit)
access : read-write
IDE : ID Extended. One/zero for extended/standard format frame.
bits : 21 - 21 (1 bit)
access : read-write
SRR : Substitute Remote Request. Contains a fixed recessive bit.
bits : 22 - 22 (1 bit)
access : read-write
RESERVED : Reserved
bits : 23 - 23 (1 bit)
access : read-only
CODE : Reserved
bits : 24 - 27 (4 bit)
access : read-write
RESERVED : Reserved
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : Reserved
bits : 29 - 29 (1 bit)
access : read-only
RESERVED : Reserved
bits : 30 - 30 (1 bit)
access : read-only
RESERVED : Reserved
bits : 31 - 31 (1 bit)
access : read-only
Message Buffer 52 ID Register
address_offset : 0x3C4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXT : Contains extended (LOW word) identifier of message buffer.
bits : 0 - 17 (18 bit)
access : read-write
STD : Contains standard/extended (HIGH word) identifier of message buffer.
bits : 18 - 28 (11 bit)
access : read-write
PRIO : Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority.
bits : 29 - 31 (3 bit)
access : read-write
Message Buffer 52 WORD0 Register
address_offset : 0x3C8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_3 : Data byte 3 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_2 : Data byte 2 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_1 : Data byte 1 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_0 : Data byte 0 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 52 WORD1 Register
address_offset : 0x3CC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_7 : Data byte 7 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_6 : Data byte 6 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_5 : Data byte 5 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_4 : Data byte 4 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 53 CS Register
address_offset : 0x3D0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TIME_STAMP : Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer, captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus.
bits : 0 - 15 (16 bit)
access : read-write
DLC : Length of the data to be stored/transmitted.
bits : 16 - 19 (4 bit)
access : read-write
RTR : Remote Transmission Request. One/zero for remote/data frame.
bits : 20 - 20 (1 bit)
access : read-write
IDE : ID Extended. One/zero for extended/standard format frame.
bits : 21 - 21 (1 bit)
access : read-write
SRR : Substitute Remote Request. Contains a fixed recessive bit.
bits : 22 - 22 (1 bit)
access : read-write
RESERVED : Reserved
bits : 23 - 23 (1 bit)
access : read-only
CODE : Reserved
bits : 24 - 27 (4 bit)
access : read-write
RESERVED : Reserved
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : Reserved
bits : 29 - 29 (1 bit)
access : read-only
RESERVED : Reserved
bits : 30 - 30 (1 bit)
access : read-only
RESERVED : Reserved
bits : 31 - 31 (1 bit)
access : read-only
Message Buffer 53 ID Register
address_offset : 0x3D4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXT : Contains extended (LOW word) identifier of message buffer.
bits : 0 - 17 (18 bit)
access : read-write
STD : Contains standard/extended (HIGH word) identifier of message buffer.
bits : 18 - 28 (11 bit)
access : read-write
PRIO : Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority.
bits : 29 - 31 (3 bit)
access : read-write
Message Buffer 53 WORD0 Register
address_offset : 0x3D8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_3 : Data byte 3 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_2 : Data byte 2 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_1 : Data byte 1 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_0 : Data byte 0 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 53 WORD1 Register
address_offset : 0x3DC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_7 : Data byte 7 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_6 : Data byte 6 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_5 : Data byte 5 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_4 : Data byte 4 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 54 CS Register
address_offset : 0x3E0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TIME_STAMP : Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer, captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus.
bits : 0 - 15 (16 bit)
access : read-write
DLC : Length of the data to be stored/transmitted.
bits : 16 - 19 (4 bit)
access : read-write
RTR : Remote Transmission Request. One/zero for remote/data frame.
bits : 20 - 20 (1 bit)
access : read-write
IDE : ID Extended. One/zero for extended/standard format frame.
bits : 21 - 21 (1 bit)
access : read-write
SRR : Substitute Remote Request. Contains a fixed recessive bit.
bits : 22 - 22 (1 bit)
access : read-write
RESERVED : Reserved
bits : 23 - 23 (1 bit)
access : read-only
CODE : Reserved
bits : 24 - 27 (4 bit)
access : read-write
RESERVED : Reserved
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : Reserved
bits : 29 - 29 (1 bit)
access : read-only
RESERVED : Reserved
bits : 30 - 30 (1 bit)
access : read-only
RESERVED : Reserved
bits : 31 - 31 (1 bit)
access : read-only
Message Buffer 54 ID Register
address_offset : 0x3E4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXT : Contains extended (LOW word) identifier of message buffer.
bits : 0 - 17 (18 bit)
access : read-write
STD : Contains standard/extended (HIGH word) identifier of message buffer.
bits : 18 - 28 (11 bit)
access : read-write
PRIO : Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority.
bits : 29 - 31 (3 bit)
access : read-write
Message Buffer 54 WORD0 Register
address_offset : 0x3E8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_3 : Data byte 3 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_2 : Data byte 2 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_1 : Data byte 1 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_0 : Data byte 0 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 54 WORD1 Register
address_offset : 0x3EC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_7 : Data byte 7 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_6 : Data byte 6 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_5 : Data byte 5 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_4 : Data byte 4 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 55 CS Register
address_offset : 0x3F0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TIME_STAMP : Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer, captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus.
bits : 0 - 15 (16 bit)
access : read-write
DLC : Length of the data to be stored/transmitted.
bits : 16 - 19 (4 bit)
access : read-write
RTR : Remote Transmission Request. One/zero for remote/data frame.
bits : 20 - 20 (1 bit)
access : read-write
IDE : ID Extended. One/zero for extended/standard format frame.
bits : 21 - 21 (1 bit)
access : read-write
SRR : Substitute Remote Request. Contains a fixed recessive bit.
bits : 22 - 22 (1 bit)
access : read-write
RESERVED : Reserved
bits : 23 - 23 (1 bit)
access : read-only
CODE : Reserved
bits : 24 - 27 (4 bit)
access : read-write
RESERVED : Reserved
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : Reserved
bits : 29 - 29 (1 bit)
access : read-only
RESERVED : Reserved
bits : 30 - 30 (1 bit)
access : read-only
RESERVED : Reserved
bits : 31 - 31 (1 bit)
access : read-only
Message Buffer 55 ID Register
address_offset : 0x3F4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXT : Contains extended (LOW word) identifier of message buffer.
bits : 0 - 17 (18 bit)
access : read-write
STD : Contains standard/extended (HIGH word) identifier of message buffer.
bits : 18 - 28 (11 bit)
access : read-write
PRIO : Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority.
bits : 29 - 31 (3 bit)
access : read-write
Message Buffer 55 WORD0 Register
address_offset : 0x3F8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_3 : Data byte 3 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_2 : Data byte 2 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_1 : Data byte 1 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_0 : Data byte 0 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 55 WORD1 Register
address_offset : 0x3FC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_7 : Data byte 7 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_6 : Data byte 6 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_5 : Data byte 5 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_4 : Data byte 4 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Control 1 register
address_offset : 0x4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PROPSEG : Propagation Segment
bits : 0 - 2 (3 bit)
access : read-write
LOM : Listen-Only Mode
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Listen-Only mode is deactivated.
#1 : 1
FlexCAN module operates in Listen-Only mode.
End of enumeration elements list.
LBUF : Lowest Buffer Transmitted First
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
Buffer with highest priority is transmitted first.
#1 : 1
Lowest number buffer is transmitted first.
End of enumeration elements list.
TSYN : Timer Sync
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
Timer Sync feature disabled
#1 : 1
Timer Sync feature enabled
End of enumeration elements list.
BOFFREC : Bus Off Recovery
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
Automatic recovering from Bus Off state enabled, according to CAN Spec 2.0 part B.
#1 : 1
Automatic recovering from Bus Off state disabled.
End of enumeration elements list.
SMP : CAN Bit Sampling
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
Just one sample is used to determine the bit value.
#1 : 1
Three samples are used to determine the value of the received bit: the regular one (sample point) and 2 preceding samples; a majority rule is used.
End of enumeration elements list.
RESERVED : no description available
bits : 8 - 9 (2 bit)
access : read-only
RWRNMSK : Rx Warning Interrupt Mask
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Rx Warning Interrupt disabled.
#1 : 1
Rx Warning Interrupt enabled.
End of enumeration elements list.
TWRNMSK : Tx Warning Interrupt Mask
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Tx Warning Interrupt disabled.
#1 : 1
Tx Warning Interrupt enabled.
End of enumeration elements list.
LPB : Loop Back Mode
bits : 12 - 12 (1 bit)
access : read-write
Enumeration:
#0 : 0
Loop Back disabled.
#1 : 1
Loop Back enabled.
End of enumeration elements list.
CLKSRC : CAN Engine Clock Source
bits : 13 - 13 (1 bit)
access : read-write
Enumeration:
#0 : 0
The CAN engine clock source is the oscillator clock. Under this condition, the oscillator clock frequency must be lower than the bus clock.
#1 : 1
The CAN engine clock source is the peripheral clock.
End of enumeration elements list.
ERRMSK : Error Mask
bits : 14 - 14 (1 bit)
access : read-write
Enumeration:
#0 : 0
Error interrupt disabled.
#1 : 1
Error interrupt enabled.
End of enumeration elements list.
BOFFMSK : Bus Off Mask
bits : 15 - 15 (1 bit)
access : read-write
Enumeration:
#0 : 0
Bus Off interrupt disabled.
#1 : 1
Bus Off interrupt enabled.
End of enumeration elements list.
PSEG2 : Phase Segment 2
bits : 16 - 18 (3 bit)
access : read-write
PSEG1 : Phase Segment 1
bits : 19 - 21 (3 bit)
access : read-write
RJW : Resync Jump Width
bits : 22 - 23 (2 bit)
access : read-write
PRESDIV : Prescaler Division Factor
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 56 CS Register
address_offset : 0x400 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TIME_STAMP : Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer, captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus.
bits : 0 - 15 (16 bit)
access : read-write
DLC : Length of the data to be stored/transmitted.
bits : 16 - 19 (4 bit)
access : read-write
RTR : Remote Transmission Request. One/zero for remote/data frame.
bits : 20 - 20 (1 bit)
access : read-write
IDE : ID Extended. One/zero for extended/standard format frame.
bits : 21 - 21 (1 bit)
access : read-write
SRR : Substitute Remote Request. Contains a fixed recessive bit.
bits : 22 - 22 (1 bit)
access : read-write
RESERVED : Reserved
bits : 23 - 23 (1 bit)
access : read-only
CODE : Reserved
bits : 24 - 27 (4 bit)
access : read-write
RESERVED : Reserved
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : Reserved
bits : 29 - 29 (1 bit)
access : read-only
RESERVED : Reserved
bits : 30 - 30 (1 bit)
access : read-only
RESERVED : Reserved
bits : 31 - 31 (1 bit)
access : read-only
Message Buffer 56 ID Register
address_offset : 0x404 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXT : Contains extended (LOW word) identifier of message buffer.
bits : 0 - 17 (18 bit)
access : read-write
STD : Contains standard/extended (HIGH word) identifier of message buffer.
bits : 18 - 28 (11 bit)
access : read-write
PRIO : Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority.
bits : 29 - 31 (3 bit)
access : read-write
Message Buffer 56 WORD0 Register
address_offset : 0x408 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_3 : Data byte 3 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_2 : Data byte 2 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_1 : Data byte 1 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_0 : Data byte 0 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 56 WORD1 Register
address_offset : 0x40C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_7 : Data byte 7 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_6 : Data byte 6 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_5 : Data byte 5 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_4 : Data byte 4 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 57 CS Register
address_offset : 0x410 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TIME_STAMP : Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer, captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus.
bits : 0 - 15 (16 bit)
access : read-write
DLC : Length of the data to be stored/transmitted.
bits : 16 - 19 (4 bit)
access : read-write
RTR : Remote Transmission Request. One/zero for remote/data frame.
bits : 20 - 20 (1 bit)
access : read-write
IDE : ID Extended. One/zero for extended/standard format frame.
bits : 21 - 21 (1 bit)
access : read-write
SRR : Substitute Remote Request. Contains a fixed recessive bit.
bits : 22 - 22 (1 bit)
access : read-write
RESERVED : Reserved
bits : 23 - 23 (1 bit)
access : read-only
CODE : Reserved
bits : 24 - 27 (4 bit)
access : read-write
RESERVED : Reserved
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : Reserved
bits : 29 - 29 (1 bit)
access : read-only
RESERVED : Reserved
bits : 30 - 30 (1 bit)
access : read-only
RESERVED : Reserved
bits : 31 - 31 (1 bit)
access : read-only
Message Buffer 57 ID Register
address_offset : 0x414 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXT : Contains extended (LOW word) identifier of message buffer.
bits : 0 - 17 (18 bit)
access : read-write
STD : Contains standard/extended (HIGH word) identifier of message buffer.
bits : 18 - 28 (11 bit)
access : read-write
PRIO : Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority.
bits : 29 - 31 (3 bit)
access : read-write
Message Buffer 57 WORD0 Register
address_offset : 0x418 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_3 : Data byte 3 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_2 : Data byte 2 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_1 : Data byte 1 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_0 : Data byte 0 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 57 WORD1 Register
address_offset : 0x41C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_7 : Data byte 7 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_6 : Data byte 6 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_5 : Data byte 5 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_4 : Data byte 4 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 58 CS Register
address_offset : 0x420 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TIME_STAMP : Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer, captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus.
bits : 0 - 15 (16 bit)
access : read-write
DLC : Length of the data to be stored/transmitted.
bits : 16 - 19 (4 bit)
access : read-write
RTR : Remote Transmission Request. One/zero for remote/data frame.
bits : 20 - 20 (1 bit)
access : read-write
IDE : ID Extended. One/zero for extended/standard format frame.
bits : 21 - 21 (1 bit)
access : read-write
SRR : Substitute Remote Request. Contains a fixed recessive bit.
bits : 22 - 22 (1 bit)
access : read-write
RESERVED : Reserved
bits : 23 - 23 (1 bit)
access : read-only
CODE : Reserved
bits : 24 - 27 (4 bit)
access : read-write
RESERVED : Reserved
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : Reserved
bits : 29 - 29 (1 bit)
access : read-only
RESERVED : Reserved
bits : 30 - 30 (1 bit)
access : read-only
RESERVED : Reserved
bits : 31 - 31 (1 bit)
access : read-only
Message Buffer 58 ID Register
address_offset : 0x424 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXT : Contains extended (LOW word) identifier of message buffer.
bits : 0 - 17 (18 bit)
access : read-write
STD : Contains standard/extended (HIGH word) identifier of message buffer.
bits : 18 - 28 (11 bit)
access : read-write
PRIO : Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority.
bits : 29 - 31 (3 bit)
access : read-write
Message Buffer 58 WORD0 Register
address_offset : 0x428 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_3 : Data byte 3 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_2 : Data byte 2 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_1 : Data byte 1 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_0 : Data byte 0 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 58 WORD1 Register
address_offset : 0x42C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_7 : Data byte 7 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_6 : Data byte 6 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_5 : Data byte 5 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_4 : Data byte 4 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 59 CS Register
address_offset : 0x430 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TIME_STAMP : Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer, captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus.
bits : 0 - 15 (16 bit)
access : read-write
DLC : Length of the data to be stored/transmitted.
bits : 16 - 19 (4 bit)
access : read-write
RTR : Remote Transmission Request. One/zero for remote/data frame.
bits : 20 - 20 (1 bit)
access : read-write
IDE : ID Extended. One/zero for extended/standard format frame.
bits : 21 - 21 (1 bit)
access : read-write
SRR : Substitute Remote Request. Contains a fixed recessive bit.
bits : 22 - 22 (1 bit)
access : read-write
RESERVED : Reserved
bits : 23 - 23 (1 bit)
access : read-only
CODE : Reserved
bits : 24 - 27 (4 bit)
access : read-write
RESERVED : Reserved
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : Reserved
bits : 29 - 29 (1 bit)
access : read-only
RESERVED : Reserved
bits : 30 - 30 (1 bit)
access : read-only
RESERVED : Reserved
bits : 31 - 31 (1 bit)
access : read-only
Message Buffer 59 ID Register
address_offset : 0x434 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXT : Contains extended (LOW word) identifier of message buffer.
bits : 0 - 17 (18 bit)
access : read-write
STD : Contains standard/extended (HIGH word) identifier of message buffer.
bits : 18 - 28 (11 bit)
access : read-write
PRIO : Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority.
bits : 29 - 31 (3 bit)
access : read-write
Message Buffer 59 WORD0 Register
address_offset : 0x438 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_3 : Data byte 3 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_2 : Data byte 2 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_1 : Data byte 1 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_0 : Data byte 0 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 59 WORD1 Register
address_offset : 0x43C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_7 : Data byte 7 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_6 : Data byte 6 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_5 : Data byte 5 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_4 : Data byte 4 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
CRC Register
address_offset : 0x44 Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
TXCRC : CRC Transmitted
bits : 0 - 14 (15 bit)
access : read-only
RESERVED : no description available
bits : 15 - 15 (1 bit)
access : read-only
MBCRC : CRC Mailbox
bits : 16 - 22 (7 bit)
access : read-only
RESERVED : no description available
bits : 23 - 31 (9 bit)
access : read-only
Message Buffer 60 CS Register
address_offset : 0x440 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TIME_STAMP : Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer, captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus.
bits : 0 - 15 (16 bit)
access : read-write
DLC : Length of the data to be stored/transmitted.
bits : 16 - 19 (4 bit)
access : read-write
RTR : Remote Transmission Request. One/zero for remote/data frame.
bits : 20 - 20 (1 bit)
access : read-write
IDE : ID Extended. One/zero for extended/standard format frame.
bits : 21 - 21 (1 bit)
access : read-write
SRR : Substitute Remote Request. Contains a fixed recessive bit.
bits : 22 - 22 (1 bit)
access : read-write
RESERVED : Reserved
bits : 23 - 23 (1 bit)
access : read-only
CODE : Reserved
bits : 24 - 27 (4 bit)
access : read-write
RESERVED : Reserved
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : Reserved
bits : 29 - 29 (1 bit)
access : read-only
RESERVED : Reserved
bits : 30 - 30 (1 bit)
access : read-only
RESERVED : Reserved
bits : 31 - 31 (1 bit)
access : read-only
Message Buffer 60 ID Register
address_offset : 0x444 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXT : Contains extended (LOW word) identifier of message buffer.
bits : 0 - 17 (18 bit)
access : read-write
STD : Contains standard/extended (HIGH word) identifier of message buffer.
bits : 18 - 28 (11 bit)
access : read-write
PRIO : Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority.
bits : 29 - 31 (3 bit)
access : read-write
Rx Individual Mask Registers
address_offset : 0x4454 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MI : Individual Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Message Buffer 60 WORD0 Register
address_offset : 0x448 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_3 : Data byte 3 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_2 : Data byte 2 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_1 : Data byte 1 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_0 : Data byte 0 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 60 WORD1 Register
address_offset : 0x44C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_7 : Data byte 7 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_6 : Data byte 6 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_5 : Data byte 5 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_4 : Data byte 4 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 61 CS Register
address_offset : 0x450 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TIME_STAMP : Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer, captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus.
bits : 0 - 15 (16 bit)
access : read-write
DLC : Length of the data to be stored/transmitted.
bits : 16 - 19 (4 bit)
access : read-write
RTR : Remote Transmission Request. One/zero for remote/data frame.
bits : 20 - 20 (1 bit)
access : read-write
IDE : ID Extended. One/zero for extended/standard format frame.
bits : 21 - 21 (1 bit)
access : read-write
SRR : Substitute Remote Request. Contains a fixed recessive bit.
bits : 22 - 22 (1 bit)
access : read-write
RESERVED : Reserved
bits : 23 - 23 (1 bit)
access : read-only
CODE : Reserved
bits : 24 - 27 (4 bit)
access : read-write
RESERVED : Reserved
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : Reserved
bits : 29 - 29 (1 bit)
access : read-only
RESERVED : Reserved
bits : 30 - 30 (1 bit)
access : read-only
RESERVED : Reserved
bits : 31 - 31 (1 bit)
access : read-only
Message Buffer 61 ID Register
address_offset : 0x454 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXT : Contains extended (LOW word) identifier of message buffer.
bits : 0 - 17 (18 bit)
access : read-write
STD : Contains standard/extended (HIGH word) identifier of message buffer.
bits : 18 - 28 (11 bit)
access : read-write
PRIO : Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority.
bits : 29 - 31 (3 bit)
access : read-write
Message Buffer 61 WORD0 Register
address_offset : 0x458 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_3 : Data byte 3 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_2 : Data byte 2 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_1 : Data byte 1 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_0 : Data byte 0 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 61 WORD1 Register
address_offset : 0x45C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_7 : Data byte 7 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_6 : Data byte 6 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_5 : Data byte 5 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_4 : Data byte 4 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 62 CS Register
address_offset : 0x460 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TIME_STAMP : Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer, captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus.
bits : 0 - 15 (16 bit)
access : read-write
DLC : Length of the data to be stored/transmitted.
bits : 16 - 19 (4 bit)
access : read-write
RTR : Remote Transmission Request. One/zero for remote/data frame.
bits : 20 - 20 (1 bit)
access : read-write
IDE : ID Extended. One/zero for extended/standard format frame.
bits : 21 - 21 (1 bit)
access : read-write
SRR : Substitute Remote Request. Contains a fixed recessive bit.
bits : 22 - 22 (1 bit)
access : read-write
RESERVED : Reserved
bits : 23 - 23 (1 bit)
access : read-only
CODE : Reserved
bits : 24 - 27 (4 bit)
access : read-write
RESERVED : Reserved
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : Reserved
bits : 29 - 29 (1 bit)
access : read-only
RESERVED : Reserved
bits : 30 - 30 (1 bit)
access : read-only
RESERVED : Reserved
bits : 31 - 31 (1 bit)
access : read-only
Message Buffer 62 ID Register
address_offset : 0x464 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXT : Contains extended (LOW word) identifier of message buffer.
bits : 0 - 17 (18 bit)
access : read-write
STD : Contains standard/extended (HIGH word) identifier of message buffer.
bits : 18 - 28 (11 bit)
access : read-write
PRIO : Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority.
bits : 29 - 31 (3 bit)
access : read-write
Message Buffer 62 WORD0 Register
address_offset : 0x468 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_3 : Data byte 3 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_2 : Data byte 2 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_1 : Data byte 1 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_0 : Data byte 0 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 62 WORD1 Register
address_offset : 0x46C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_7 : Data byte 7 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_6 : Data byte 6 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_5 : Data byte 5 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_4 : Data byte 4 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 63 CS Register
address_offset : 0x470 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TIME_STAMP : Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer, captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus.
bits : 0 - 15 (16 bit)
access : read-write
DLC : Length of the data to be stored/transmitted.
bits : 16 - 19 (4 bit)
access : read-write
RTR : Remote Transmission Request. One/zero for remote/data frame.
bits : 20 - 20 (1 bit)
access : read-write
IDE : ID Extended. One/zero for extended/standard format frame.
bits : 21 - 21 (1 bit)
access : read-write
SRR : Substitute Remote Request. Contains a fixed recessive bit.
bits : 22 - 22 (1 bit)
access : read-write
RESERVED : Reserved
bits : 23 - 23 (1 bit)
access : read-only
CODE : Reserved
bits : 24 - 27 (4 bit)
access : read-write
RESERVED : Reserved
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : Reserved
bits : 29 - 29 (1 bit)
access : read-only
RESERVED : Reserved
bits : 30 - 30 (1 bit)
access : read-only
RESERVED : Reserved
bits : 31 - 31 (1 bit)
access : read-only
Message Buffer 63 ID Register
address_offset : 0x474 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXT : Contains extended (LOW word) identifier of message buffer.
bits : 0 - 17 (18 bit)
access : read-write
STD : Contains standard/extended (HIGH word) identifier of message buffer.
bits : 18 - 28 (11 bit)
access : read-write
PRIO : Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority.
bits : 29 - 31 (3 bit)
access : read-write
Message Buffer 63 WORD0 Register
address_offset : 0x478 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_3 : Data byte 3 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_2 : Data byte 2 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_1 : Data byte 1 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_0 : Data byte 0 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 63 WORD1 Register
address_offset : 0x47C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_7 : Data byte 7 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_6 : Data byte 6 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_5 : Data byte 5 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_4 : Data byte 4 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Rx FIFO Global Mask register
address_offset : 0x48 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FGM : Rx FIFO Global Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Rx FIFO Information Register
address_offset : 0x4C Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
IDHIT : Identifier Acceptance Filter Hit Indicator
bits : 0 - 8 (9 bit)
access : read-only
RESERVED : no description available
bits : 9 - 31 (23 bit)
access : read-only
Rx Individual Mask Registers
address_offset : 0x4CF0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MI : Individual Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Rx Individual Mask Registers
address_offset : 0x5590 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MI : Individual Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Rx Individual Mask Registers
address_offset : 0x5E34 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MI : Individual Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Rx Individual Mask Registers
address_offset : 0x66DC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MI : Individual Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Rx Individual Mask Registers
address_offset : 0x6F88 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MI : Individual Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Rx Individual Mask Registers
address_offset : 0x7838 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MI : Individual Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Free Running Timer
address_offset : 0x8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TIMER : Timer Value
bits : 0 - 15 (16 bit)
access : read-write
RESERVED : no description available
bits : 16 - 31 (16 bit)
access : read-only
Message Buffer 0 CS Register
address_offset : 0x80 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TIME_STAMP : Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer, captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus.
bits : 0 - 15 (16 bit)
access : read-write
DLC : Length of the data to be stored/transmitted.
bits : 16 - 19 (4 bit)
access : read-write
RTR : Remote Transmission Request. One/zero for remote/data frame.
bits : 20 - 20 (1 bit)
access : read-write
IDE : ID Extended. One/zero for extended/standard format frame.
bits : 21 - 21 (1 bit)
access : read-write
SRR : Substitute Remote Request. Contains a fixed recessive bit.
bits : 22 - 22 (1 bit)
access : read-write
RESERVED : Reserved
bits : 23 - 23 (1 bit)
access : read-only
CODE : Reserved
bits : 24 - 27 (4 bit)
access : read-write
RESERVED : Reserved
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : Reserved
bits : 29 - 29 (1 bit)
access : read-only
RESERVED : Reserved
bits : 30 - 30 (1 bit)
access : read-only
RESERVED : Reserved
bits : 31 - 31 (1 bit)
access : read-only
Rx Individual Mask Registers
address_offset : 0x80EC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MI : Individual Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Message Buffer 0 ID Register
address_offset : 0x84 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXT : Contains extended (LOW word) identifier of message buffer.
bits : 0 - 17 (18 bit)
access : read-write
STD : Contains standard/extended (HIGH word) identifier of message buffer.
bits : 18 - 28 (11 bit)
access : read-write
PRIO : Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority.
bits : 29 - 31 (3 bit)
access : read-write
Message Buffer 0 WORD0 Register
address_offset : 0x88 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_3 : Data byte 3 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_2 : Data byte 2 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_1 : Data byte 1 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_0 : Data byte 0 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Rx Individual Mask Registers
address_offset : 0x89A4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MI : Individual Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Message Buffer 0 WORD1 Register
address_offset : 0x8C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_7 : Data byte 7 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_6 : Data byte 6 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_5 : Data byte 5 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_4 : Data byte 4 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 1 CS Register
address_offset : 0x90 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TIME_STAMP : Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer, captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus.
bits : 0 - 15 (16 bit)
access : read-write
DLC : Length of the data to be stored/transmitted.
bits : 16 - 19 (4 bit)
access : read-write
RTR : Remote Transmission Request. One/zero for remote/data frame.
bits : 20 - 20 (1 bit)
access : read-write
IDE : ID Extended. One/zero for extended/standard format frame.
bits : 21 - 21 (1 bit)
access : read-write
SRR : Substitute Remote Request. Contains a fixed recessive bit.
bits : 22 - 22 (1 bit)
access : read-write
RESERVED : Reserved
bits : 23 - 23 (1 bit)
access : read-only
CODE : Reserved
bits : 24 - 27 (4 bit)
access : read-write
RESERVED : Reserved
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : Reserved
bits : 29 - 29 (1 bit)
access : read-only
RESERVED : Reserved
bits : 30 - 30 (1 bit)
access : read-only
RESERVED : Reserved
bits : 31 - 31 (1 bit)
access : read-only
Rx Individual Mask Registers
address_offset : 0x9260 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MI : Individual Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Message Buffer 1 ID Register
address_offset : 0x94 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXT : Contains extended (LOW word) identifier of message buffer.
bits : 0 - 17 (18 bit)
access : read-write
STD : Contains standard/extended (HIGH word) identifier of message buffer.
bits : 18 - 28 (11 bit)
access : read-write
PRIO : Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority.
bits : 29 - 31 (3 bit)
access : read-write
Message Buffer 1 WORD0 Register
address_offset : 0x98 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_3 : Data byte 3 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_2 : Data byte 2 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_1 : Data byte 1 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_0 : Data byte 0 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Rx Individual Mask Registers
address_offset : 0x9B20 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MI : Individual Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Message Buffer 1 WORD1 Register
address_offset : 0x9C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_7 : Data byte 7 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_6 : Data byte 6 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_5 : Data byte 5 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_4 : Data byte 4 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 2 CS Register
address_offset : 0xA0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TIME_STAMP : Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer, captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus.
bits : 0 - 15 (16 bit)
access : read-write
DLC : Length of the data to be stored/transmitted.
bits : 16 - 19 (4 bit)
access : read-write
RTR : Remote Transmission Request. One/zero for remote/data frame.
bits : 20 - 20 (1 bit)
access : read-write
IDE : ID Extended. One/zero for extended/standard format frame.
bits : 21 - 21 (1 bit)
access : read-write
SRR : Substitute Remote Request. Contains a fixed recessive bit.
bits : 22 - 22 (1 bit)
access : read-write
RESERVED : Reserved
bits : 23 - 23 (1 bit)
access : read-only
CODE : Reserved
bits : 24 - 27 (4 bit)
access : read-write
RESERVED : Reserved
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : Reserved
bits : 29 - 29 (1 bit)
access : read-only
RESERVED : Reserved
bits : 30 - 30 (1 bit)
access : read-only
RESERVED : Reserved
bits : 31 - 31 (1 bit)
access : read-only
Rx Individual Mask Registers
address_offset : 0xA3E4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MI : Individual Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Message Buffer 2 ID Register
address_offset : 0xA4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXT : Contains extended (LOW word) identifier of message buffer.
bits : 0 - 17 (18 bit)
access : read-write
STD : Contains standard/extended (HIGH word) identifier of message buffer.
bits : 18 - 28 (11 bit)
access : read-write
PRIO : Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority.
bits : 29 - 31 (3 bit)
access : read-write
Message Buffer 2 WORD0 Register
address_offset : 0xA8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_3 : Data byte 3 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_2 : Data byte 2 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_1 : Data byte 1 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_0 : Data byte 0 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 2 WORD1 Register
address_offset : 0xAC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_7 : Data byte 7 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_6 : Data byte 6 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_5 : Data byte 5 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_4 : Data byte 4 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Rx Individual Mask Registers
address_offset : 0xACAC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MI : Individual Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Memory Error Control Register
address_offset : 0xAE0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RESERVED : no description available
bits : 0 - 6 (7 bit)
access : read-only
NCEFAFRZ : Non-Correctable Errors In FlexCAN Access Put Device In Freeze Mode
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
Keep normal operation.
#1 : 1
Put FlexCAN in Freeze mode (according to the "Freeze mode" section).
End of enumeration elements list.
ECCDIS : Error Correction Disable
bits : 8 - 8 (1 bit)
access : read-write
Enumeration:
#0 : 0
Enable memory error correction.
#1 : 1
Disable memory error correction.
End of enumeration elements list.
RERRDIS : Error Report Disable
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
Enable updates of the error report registers.
#1 : 1
Disable updates of the error report registers.
End of enumeration elements list.
RESERVED : no description available
bits : 10 - 12 (3 bit)
access : read-only
EXTERRIE : Extended Error Injection Enable
bits : 13 - 13 (1 bit)
access : read-write
Enumeration:
#0 : 0
Error injection is applied only to the 32-bit word.
#1 : 1
Error injection is applied to the 64-bit word.
End of enumeration elements list.
FAERRIE : FlexCAN Access Error Injection Enable
bits : 14 - 14 (1 bit)
access : read-write
Enumeration:
#0 : 0
Injection is disabled.
#1 : 1
Injection is enabled.
End of enumeration elements list.
HAERRIE : Host Access Error Injection Enable
bits : 15 - 15 (1 bit)
access : read-write
Enumeration:
#0 : 0
Injection is disabled.
#1 : 1
Injection is enabled.
End of enumeration elements list.
CEI_MSK : Correctable Errors Interrupt Mask
bits : 16 - 16 (1 bit)
access : read-write
Enumeration:
#0 : 0
Interrupt is disabled.
#1 : 1
Interrupt is enabled.
End of enumeration elements list.
RESERVED : no description available
bits : 17 - 17 (1 bit)
access : read-only
FANCEI_MSK : FlexCAN Access With Non-Correctable Errors Interrupt Mask
bits : 18 - 18 (1 bit)
access : read-write
Enumeration:
#0 : 0
Interrupt is disabled.
#1 : 1
Interrupt is enabled.
End of enumeration elements list.
HANCEI_MSK : Host Access With Non-Correctable Errors Interrupt Mask
bits : 19 - 19 (1 bit)
access : read-write
Enumeration:
#0 : 0
Interrupt is disabled.
#1 : 1
Interrupt is enabled.
End of enumeration elements list.
RESERVED : no description available
bits : 20 - 30 (11 bit)
access : read-only
ECRWRDIS : Error Configuration Register Write Disable
bits : 31 - 31 (1 bit)
access : read-write
Enumeration:
#0 : 0
Write is enabled.
#1 : 1
Write is disabled.
End of enumeration elements list.
Error Injection Address Register
address_offset : 0xAE4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
INJADDR : Address Where Error Is To Be Injected
bits : 0 - 13 (14 bit)
access : read-write
RESERVED : no description available
bits : 14 - 31 (18 bit)
access : read-only
Error Injection Data Pattern Register
address_offset : 0xAE8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DFLIP : Data flip pattern
bits : 0 - 31 (32 bit)
access : read-write
Error Injection Parity Pattern Register
address_offset : 0xAEC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PFLIP0 : Parity Flip Pattern For Byte 0 (Least Significant)
bits : 0 - 4 (5 bit)
access : read-write
RESERVED : no description available
bits : 5 - 7 (3 bit)
access : read-only
PFLIP1 : Parity Flip Pattern For Byte 1
bits : 8 - 12 (5 bit)
access : read-write
RESERVED : no description available
bits : 13 - 15 (3 bit)
access : read-only
PFLIP2 : Parity Flip Pattern For Byte 2
bits : 16 - 20 (5 bit)
access : read-write
RESERVED : no description available
bits : 21 - 23 (3 bit)
access : read-only
PFLIP3 : Parity Flip Pattern For Byte 3 (most significant)
bits : 24 - 28 (5 bit)
access : read-write
RESERVED : no description available
bits : 29 - 31 (3 bit)
access : read-only
Error Report Address Register
address_offset : 0xAF0 Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
ERRADDR : Address Where The Error Was Detected
bits : 0 - 13 (14 bit)
access : read-only
RESERVED : no description available
bits : 14 - 15 (2 bit)
access : read-only
SAID : no description available
bits : 16 - 18 (3 bit)
access : read-only
RESERVED : no description available
bits : 19 - 23 (5 bit)
access : read-only
NCE : Non-Correctable Error
bits : 24 - 24 (1 bit)
access : read-only
Enumeration:
#0 : 0
Reporting a correctable-error
#1 : 1
Reporting a non-correctable error
End of enumeration elements list.
RESERVED : no description available
bits : 25 - 31 (7 bit)
access : read-only
Error Report Data Register
address_offset : 0xAF4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RDATA : Raw data word read from memory with error
bits : 0 - 31 (32 bit)
access : read-write
Error Report Syndrome Register
address_offset : 0xAF8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
SYND0 : Error Syndrome For Byte 0 (least significant)
bits : 0 - 4 (5 bit)
access : read-write
RESERVED : no description available
bits : 5 - 6 (2 bit)
access : read-only
BE0 : Byte Enabled For Byte 0 (least significant)
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
The byte was not read.
#1 : 1
The byte was read.
End of enumeration elements list.
SYND1 : Error Syndrome for Byte 1
bits : 8 - 12 (5 bit)
access : read-write
RESERVED : no description available
bits : 13 - 14 (2 bit)
access : read-only
BE1 : Byte Enabled For Byte 1
bits : 15 - 15 (1 bit)
access : read-write
Enumeration:
#0 : 0
The byte was not read.
#1 : 1
The byte was read.
End of enumeration elements list.
SYND2 : Error Syndrome For Byte 2
bits : 16 - 20 (5 bit)
access : read-write
RESERVED : no description available
bits : 21 - 22 (2 bit)
access : read-only
BE2 : Byte Enabled For Byte 2
bits : 23 - 23 (1 bit)
access : read-write
Enumeration:
#0 : 0
The byte was not read.
#1 : 1
The byte was read.
End of enumeration elements list.
SYND3 : Error Syndrome For Byte 3 (Most Significant)
bits : 24 - 28 (5 bit)
access : read-write
RESERVED : no description available
bits : 29 - 30 (2 bit)
access : read-only
BE3 : Byte Enabled For Byte 3 (Most Significant)
bits : 31 - 31 (1 bit)
access : read-write
Enumeration:
#0 : 0
The byte was not read.
#1 : 1
The byte was read.
End of enumeration elements list.
Error Status Register
address_offset : 0xAFC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
CEIOF : Correctable Error Interrupt Overrun Flag
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
No overrun on correctable errors
#1 : 1
Overrun on correctable errors
End of enumeration elements list.
RESERVED : no description available
bits : 1 - 1 (1 bit)
access : read-only
FANCEIOF : FlexCAN Access With Non-Correctable Error Interrupt Overrun Flag
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
No overrun on non-correctable errors in FlexCAN access
#1 : 1
Overrun on non-correctable errors in FlexCAN access
End of enumeration elements list.
HANCEIOF : Host Access With Non-Correctable Error Interrupt Overrun Flag
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
No overrun on non-correctable errors in Host access
#1 : 1
Overrun on non-correctable errors in Host access
End of enumeration elements list.
RESERVED : no description available
bits : 4 - 15 (12 bit)
access : read-only
CEIF : Correctable Error Interrupt Flag
bits : 16 - 16 (1 bit)
access : read-write
Enumeration:
#0 : 0
No correctable errors were detected so far.
#1 : 1
A correctable error was detected.
End of enumeration elements list.
RESERVED : no description available
bits : 17 - 17 (1 bit)
access : read-only
FANCEIF : FlexCAN Access With Non-Correctable Error Interrupt Flag
bits : 18 - 18 (1 bit)
access : read-write
Enumeration:
#0 : 0
No non-correctable errors were detected in FlexCAN accesses so far.
#1 : 1
A non-correctable error was detected in a FlexCAN access.
End of enumeration elements list.
HANCEIF : Host Access With Non-Correctable Error Interrupt Flag
bits : 19 - 19 (1 bit)
access : read-write
Enumeration:
#0 : 0
No non-correctable errors were detected in Host accesses so far.
#1 : 1
A non-correctable error was detected in a Host access.
End of enumeration elements list.
RESERVED : no description available
bits : 20 - 31 (12 bit)
access : read-only
Message Buffer 3 CS Register
address_offset : 0xB0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TIME_STAMP : Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer, captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus.
bits : 0 - 15 (16 bit)
access : read-write
DLC : Length of the data to be stored/transmitted.
bits : 16 - 19 (4 bit)
access : read-write
RTR : Remote Transmission Request. One/zero for remote/data frame.
bits : 20 - 20 (1 bit)
access : read-write
IDE : ID Extended. One/zero for extended/standard format frame.
bits : 21 - 21 (1 bit)
access : read-write
SRR : Substitute Remote Request. Contains a fixed recessive bit.
bits : 22 - 22 (1 bit)
access : read-write
RESERVED : Reserved
bits : 23 - 23 (1 bit)
access : read-only
CODE : Reserved
bits : 24 - 27 (4 bit)
access : read-write
RESERVED : Reserved
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : Reserved
bits : 29 - 29 (1 bit)
access : read-only
RESERVED : Reserved
bits : 30 - 30 (1 bit)
access : read-only
RESERVED : Reserved
bits : 31 - 31 (1 bit)
access : read-only
Message Buffer 3 ID Register
address_offset : 0xB4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXT : Contains extended (LOW word) identifier of message buffer.
bits : 0 - 17 (18 bit)
access : read-write
STD : Contains standard/extended (HIGH word) identifier of message buffer.
bits : 18 - 28 (11 bit)
access : read-write
PRIO : Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority.
bits : 29 - 31 (3 bit)
access : read-write
Rx Individual Mask Registers
address_offset : 0xB578 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MI : Individual Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Message Buffer 3 WORD0 Register
address_offset : 0xB8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_3 : Data byte 3 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_2 : Data byte 2 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_1 : Data byte 1 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_0 : Data byte 0 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 3 WORD1 Register
address_offset : 0xBC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_7 : Data byte 7 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_6 : Data byte 6 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_5 : Data byte 5 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_4 : Data byte 4 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Rx Individual Mask Registers
address_offset : 0xBE48 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MI : Individual Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Message Buffer 4 CS Register
address_offset : 0xC0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TIME_STAMP : Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer, captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus.
bits : 0 - 15 (16 bit)
access : read-write
DLC : Length of the data to be stored/transmitted.
bits : 16 - 19 (4 bit)
access : read-write
RTR : Remote Transmission Request. One/zero for remote/data frame.
bits : 20 - 20 (1 bit)
access : read-write
IDE : ID Extended. One/zero for extended/standard format frame.
bits : 21 - 21 (1 bit)
access : read-write
SRR : Substitute Remote Request. Contains a fixed recessive bit.
bits : 22 - 22 (1 bit)
access : read-write
RESERVED : Reserved
bits : 23 - 23 (1 bit)
access : read-only
CODE : Reserved
bits : 24 - 27 (4 bit)
access : read-write
RESERVED : Reserved
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : Reserved
bits : 29 - 29 (1 bit)
access : read-only
RESERVED : Reserved
bits : 30 - 30 (1 bit)
access : read-only
RESERVED : Reserved
bits : 31 - 31 (1 bit)
access : read-only
Message Buffer 4 ID Register
address_offset : 0xC4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXT : Contains extended (LOW word) identifier of message buffer.
bits : 0 - 17 (18 bit)
access : read-write
STD : Contains standard/extended (HIGH word) identifier of message buffer.
bits : 18 - 28 (11 bit)
access : read-write
PRIO : Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority.
bits : 29 - 31 (3 bit)
access : read-write
Rx Individual Mask Registers
address_offset : 0xC71C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MI : Individual Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Message Buffer 4 WORD0 Register
address_offset : 0xC8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_3 : Data byte 3 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_2 : Data byte 2 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_1 : Data byte 1 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_0 : Data byte 0 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 4 WORD1 Register
address_offset : 0xCC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_7 : Data byte 7 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_6 : Data byte 6 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_5 : Data byte 5 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_4 : Data byte 4 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Rx Individual Mask Registers
address_offset : 0xCFF4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MI : Individual Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Message Buffer 5 CS Register
address_offset : 0xD0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TIME_STAMP : Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer, captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus.
bits : 0 - 15 (16 bit)
access : read-write
DLC : Length of the data to be stored/transmitted.
bits : 16 - 19 (4 bit)
access : read-write
RTR : Remote Transmission Request. One/zero for remote/data frame.
bits : 20 - 20 (1 bit)
access : read-write
IDE : ID Extended. One/zero for extended/standard format frame.
bits : 21 - 21 (1 bit)
access : read-write
SRR : Substitute Remote Request. Contains a fixed recessive bit.
bits : 22 - 22 (1 bit)
access : read-write
RESERVED : Reserved
bits : 23 - 23 (1 bit)
access : read-only
CODE : Reserved
bits : 24 - 27 (4 bit)
access : read-write
RESERVED : Reserved
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : Reserved
bits : 29 - 29 (1 bit)
access : read-only
RESERVED : Reserved
bits : 30 - 30 (1 bit)
access : read-only
RESERVED : Reserved
bits : 31 - 31 (1 bit)
access : read-only
Message Buffer 5 ID Register
address_offset : 0xD4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXT : Contains extended (LOW word) identifier of message buffer.
bits : 0 - 17 (18 bit)
access : read-write
STD : Contains standard/extended (HIGH word) identifier of message buffer.
bits : 18 - 28 (11 bit)
access : read-write
PRIO : Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority.
bits : 29 - 31 (3 bit)
access : read-write
Message Buffer 5 WORD0 Register
address_offset : 0xD8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_3 : Data byte 3 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_2 : Data byte 2 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_1 : Data byte 1 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_0 : Data byte 0 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Rx Individual Mask Registers
address_offset : 0xD8D0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MI : Individual Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Message Buffer 5 WORD1 Register
address_offset : 0xDC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_7 : Data byte 7 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_6 : Data byte 6 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_5 : Data byte 5 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_4 : Data byte 4 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 6 CS Register
address_offset : 0xE0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TIME_STAMP : Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer, captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus.
bits : 0 - 15 (16 bit)
access : read-write
DLC : Length of the data to be stored/transmitted.
bits : 16 - 19 (4 bit)
access : read-write
RTR : Remote Transmission Request. One/zero for remote/data frame.
bits : 20 - 20 (1 bit)
access : read-write
IDE : ID Extended. One/zero for extended/standard format frame.
bits : 21 - 21 (1 bit)
access : read-write
SRR : Substitute Remote Request. Contains a fixed recessive bit.
bits : 22 - 22 (1 bit)
access : read-write
RESERVED : Reserved
bits : 23 - 23 (1 bit)
access : read-only
CODE : Reserved
bits : 24 - 27 (4 bit)
access : read-write
RESERVED : Reserved
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : Reserved
bits : 29 - 29 (1 bit)
access : read-only
RESERVED : Reserved
bits : 30 - 30 (1 bit)
access : read-only
RESERVED : Reserved
bits : 31 - 31 (1 bit)
access : read-only
Rx Individual Mask Registers
address_offset : 0xE1B0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MI : Individual Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Message Buffer 6 ID Register
address_offset : 0xE4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXT : Contains extended (LOW word) identifier of message buffer.
bits : 0 - 17 (18 bit)
access : read-write
STD : Contains standard/extended (HIGH word) identifier of message buffer.
bits : 18 - 28 (11 bit)
access : read-write
PRIO : Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority.
bits : 29 - 31 (3 bit)
access : read-write
Message Buffer 6 WORD0 Register
address_offset : 0xE8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_3 : Data byte 3 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_2 : Data byte 2 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_1 : Data byte 1 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_0 : Data byte 0 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Rx Individual Mask Registers
address_offset : 0xEA94 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MI : Individual Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Message Buffer 6 WORD1 Register
address_offset : 0xEC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_7 : Data byte 7 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_6 : Data byte 6 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_5 : Data byte 5 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_4 : Data byte 4 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 7 CS Register
address_offset : 0xF0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TIME_STAMP : Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer, captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus.
bits : 0 - 15 (16 bit)
access : read-write
DLC : Length of the data to be stored/transmitted.
bits : 16 - 19 (4 bit)
access : read-write
RTR : Remote Transmission Request. One/zero for remote/data frame.
bits : 20 - 20 (1 bit)
access : read-write
IDE : ID Extended. One/zero for extended/standard format frame.
bits : 21 - 21 (1 bit)
access : read-write
SRR : Substitute Remote Request. Contains a fixed recessive bit.
bits : 22 - 22 (1 bit)
access : read-write
RESERVED : Reserved
bits : 23 - 23 (1 bit)
access : read-only
CODE : Reserved
bits : 24 - 27 (4 bit)
access : read-write
RESERVED : Reserved
bits : 28 - 28 (1 bit)
access : read-only
RESERVED : Reserved
bits : 29 - 29 (1 bit)
access : read-only
RESERVED : Reserved
bits : 30 - 30 (1 bit)
access : read-only
RESERVED : Reserved
bits : 31 - 31 (1 bit)
access : read-only
Rx Individual Mask Registers
address_offset : 0xF37C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MI : Individual Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Message Buffer 7 ID Register
address_offset : 0xF4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXT : Contains extended (LOW word) identifier of message buffer.
bits : 0 - 17 (18 bit)
access : read-write
STD : Contains standard/extended (HIGH word) identifier of message buffer.
bits : 18 - 28 (11 bit)
access : read-write
PRIO : Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority.
bits : 29 - 31 (3 bit)
access : read-write
Message Buffer 7 WORD0 Register
address_offset : 0xF8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_3 : Data byte 3 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_2 : Data byte 2 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_1 : Data byte 1 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_0 : Data byte 0 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Message Buffer 7 WORD1 Register
address_offset : 0xFC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA_BYTE_7 : Data byte 7 of Rx/Tx frame.
bits : 0 - 7 (8 bit)
access : read-write
DATA_BYTE_6 : Data byte 6 of Rx/Tx frame.
bits : 8 - 15 (8 bit)
access : read-write
DATA_BYTE_5 : Data byte 5 of Rx/Tx frame.
bits : 16 - 23 (8 bit)
access : read-write
DATA_BYTE_4 : Data byte 4 of Rx/Tx frame.
bits : 24 - 31 (8 bit)
access : read-write
Rx Individual Mask Registers
address_offset : 0xFC68 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MI : Individual Mask Bits
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
#0 : 0
The corresponding bit in the filter is "don't care."
#1 : 1
The corresponding bit in the filter is checked.
End of enumeration elements list.
Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !
This website is sponsored by Embeetle, an IDE designed from scratch for embedded software developers.