\n
address_offset : 0x0 Bytes (0x0)
size : 0x8 byte (0x0)
mem_usage : registers
protection : not protected
Port Filter Control Register 0
address_offset : 0x0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FLTRST : Filter Selection for Input from RESET
bits : 0 - 1 (2 bit)
access : read-write
Enumeration:
#00 : 00
No filter.
#01 : 01
Selects FLTDIV1, and will switch to FLTDIV3 in Stop mode automatically.
#10 : 10
Selects FLTDIV2, and will switch to FLTDIV3 in Stop mode automatically.
#11 : 11
FLTDIV3
End of enumeration elements list.
FLTDIV1 : Filter Division Set 1
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
#00 : 00
BUSCLK/2
#01 : 01
BUSCLK/4
#10 : 10
BUSCLK/8
#11 : 11
BUSCLK/16
End of enumeration elements list.
FLTDIV2 : Filter Division Set 2
bits : 26 - 28 (3 bit)
access : read-write
Enumeration:
#000 : 000
BUSCLK/32
#001 : 001
BUSCLK/64
#010 : 010
BUSCLK/128
#011 : 011
BUSCLK/256
#100 : 100
BUSCLK/512
#101 : 101
BUSCLK/1024
#110 : 110
BUSCLK/2048
#111 : 111
BUSCLK/4096
End of enumeration elements list.
FLTDIV3 : Filter Division Set 3
bits : 29 - 31 (3 bit)
access : read-write
Enumeration:
#000 : 000
LPOCLK
#001 : 001
LPOCLK/2
#010 : 010
LPOCLK/4
#011 : 011
LPOCLK/8
#100 : 100
LPOCLK/16
#101 : 101
LPOCLK/32
#110 : 110
LPOCLK/64
#111 : 111
LPOCLK/128
End of enumeration elements list.
Port Pullup Enable Register 0
address_offset : 0x4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PTAPE0 : Pull Enable for Port A Bit 0
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pullup is disabled for port A bit 0.
#1 : 1
Pullup is enabled for port A bit 0.
End of enumeration elements list.
PTAPE1 : Pull Enable for Port A Bit 1
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pullup is disabled for port A bit 1.
#1 : 1
Pullup is enabled for port A bit 1.
End of enumeration elements list.
PTAPE2 : Pull Enable for Port A Bit 2
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pullup is disabled for port A bit 2.
#1 : 1
Pullup is enabled for port A bit 2.
End of enumeration elements list.
PTAPE3 : Pull Enable for Port A Bit 3
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pullup is disabled for port A bit 3.
#1 : 1
Pullup is enabled for port A bit 3.
End of enumeration elements list.
PTAPE4 : Pull Enable for Port A Bit 4
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pullup is disabled for port A bit 4.
#1 : 1
Pullup is enabled for port A bit 4.
End of enumeration elements list.
PTAPE5 : Pull Enable for Port A Bit 5
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pullup is disabled for port A bit 5.
#1 : 1
Pullup is enabled for port A bit 5.
End of enumeration elements list.
PTAPE6 : Pull Enable for Port A Bit 6
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pullup is disabled for port A bit 6.
#1 : 1
Pullup is enabled for port A bit 6.
End of enumeration elements list.
PTAPE7 : Pull Enable for Port A Bit 7
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pullup is disabled for port A bit 7.
#1 : 1
Pullup is enabled for port A bit 7.
End of enumeration elements list.
PTBPE0 : Pull Enable for Port B Bit 0
bits : 8 - 8 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pullup is disabled for port B bit 0.
#1 : 1
Pullup is enabled for port B bit 0.
End of enumeration elements list.
PTBPE1 : Pull Enable for Port B Bit 1
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pullup is disabled for port B bit 1.
#1 : 1
Pullup is enabled for port B bit 1.
End of enumeration elements list.
PTBPE2 : Pull Enable for Port B Bit 2
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pullup is disabled for port B bit 2.
#1 : 1
Pullup is enabled for port B bit 2.
End of enumeration elements list.
PTBPE3 : Pull Enable for Port B Bit 3
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pullup is disabled for port B bit 3.
#1 : 1
Pullup is enabled for port B bit 3.
End of enumeration elements list.
PTBPE4 : Pull Enable for Port B Bit 4
bits : 12 - 12 (1 bit)
access : read-write
Enumeration:
#0 : 0
Pullup is disabled for port B bit 4.
#1 : 1
Pullup is enabled for port B bit 4.
End of enumeration elements list.
Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !
This website is sponsored by Embeetle, an IDE designed from scratch for embedded software developers.