Embeetle, an IDE designed from scratch for embedded software developers.address_offset : 0x0 Bytes (0x0)
size : 0x50 byte (0x0)
mem_usage : registers
protection : not protected
High Side Driver Interrupt Enable Register
address_offset : 0x10 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
HS1_OT_IEN : High Side 1 Overtemperature interrupt enable
bits : 5 - 4 (0 bit)
access : read-write
Enumeration:
0b0 : disabled
None
0b1 : enable
None
End of enumeration elements list.
HS1_OL_IEN : High Side 1 Open Load interrupt enable
bits : 6 - 5 (0 bit)
access : read-write
Enumeration:
0b0 : disable
None
0b1 : enable
None
End of enumeration elements list.
HS1_OC_IEN : High Side 1 Overcurrent interrupt enable
bits : 7 - 6 (0 bit)
access : read-write
Enumeration:
0b0 : disable
None
0b1 : enable
None
End of enumeration elements list.
HS2_OT_IEN : High Side 2 Overtemperature interrupt enable
bits : 21 - 20 (0 bit)
access : read-write
Enumeration:
0b0 : disabled
None
0b1 : enable
None
End of enumeration elements list.
HS2_OL_IEN : High Side 2 Open Load interrupt enable
bits : 22 - 21 (0 bit)
access : read-write
Enumeration:
0b0 : disable
None
0b1 : enable
None
End of enumeration elements list.
HS2_OC_IEN : High Side 2 Overcurrent interrupt enable
bits : 23 - 22 (0 bit)
access : read-write
Enumeration:
0b0 : disable
None
0b1 : enable
None
End of enumeration elements list.
High Side Driver 1 TRIM
address_offset : 0x1C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
HS1_OL_BTFILT_SEL : Blanking Time Filter Select for HS1 Open Load Detection
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
0b00 : 2_us
4 us filter time
0b01 : 4_us
8 us filter time
0b10 : 8_us
16 us filter time
0b11 : 16_us
32 us filter time
End of enumeration elements list.
HS1_OC_OT_BTFILT_SEL : Blanking Time Filter Select for HS1 Overcurrent / Overtemperature Detection
bits : 8 - 8 (1 bit)
access : read-write
Enumeration:
0b00 : 4_us
4 us filter time
0b01 : 8_us
8 us filter time
0b10 : 16_us
16 us filter time
0b11 : 32_us
32 us filter time
End of enumeration elements list.
High Side Driver 2 TRIM
address_offset : 0x20 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
HS2_OL_BTFILT_SEL : Blanking Time Filter Select for HS2 Open Load Detection
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
0b00 : 2_us
4 us filter time
0b01 : 4_us
8 us filter time
0b10 : 8_us
16 us filter time
0b11 : 16_us
32 us filter time
End of enumeration elements list.
HS2_OC_OT_BTFILT_SEL : Blanking Time Filter Select for HS2 Overcurrent / Overtemperature Detection
bits : 8 - 8 (1 bit)
access : read-write
Enumeration:
0b00 : 4_us
4 us filter time
0b01 : 8_us
8 us filter time
0b10 : 16_us
16 us filter time
0b11 : 32_us
32 us filter time
End of enumeration elements list.
High Side PWM Source Selection Register
address_offset : 0x24 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
HS2_SRC_SEL : HS2 PWM Source Selection
bits : 0 - 1 (2 bit)
access : read-write
Enumeration:
0b0000 : CC60
PWM output of CCU6
0b0001 : CC61
PWM output of CCU6
0b0010 : CC62
PWM output of CCU6
0b0011 : COUT60
PWM output of CCU6
0b0100 : COUT61
PWM output of CCU6
0b0101 : COUT62
PWM output of CCU6
0b0110 : T3OUT
PWM output of GPT12
End of enumeration elements list.
HS1_SRC_SEL : HS1 PWM Source Selection
bits : 3 - 4 (2 bit)
access : read-write
Enumeration:
0b0000 : CC60
PWM output of CCU6
0b0001 : CC61
PWM output of CCU6
0b0010 : CC62
PWM output of CCU6
0b0011 : COUT60
PWM output of CCU6
0b0100 : COUT61
PWM output of CCU6
0b0101 : COUT62
PWM output of CCU6
0b0110 : T3OUT
PWM output of GPT12
End of enumeration elements list.
High Side Driver Control
address_offset : 0x4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
HS1_EN : High Side 1 Enable
bits : 0 - -1 (0 bit)
access : read-write
Enumeration:
0b0 : DISABLE
HS circuit power off
0b1 : ENABLE
HS circuit power on
End of enumeration elements list.
HS1_PWM : High Side 1 PWM Enable
bits : 1 - 0 (0 bit)
access : read-write
Enumeration:
0b0 : DISABLE
disables control by PWM input
0b1 : ENABLE
enables control by PWM input
End of enumeration elements list.
HS1_ON : High Side 1 On
bits : 2 - 1 (0 bit)
access : read-write
Enumeration:
0b0 : OFF
HS driver off
0b1 : ON
HS driver on
End of enumeration elements list.
HS1_OL_EN : High Side 1 Open Load Detection Enable
bits : 3 - 2 (0 bit)
access : read-write
Enumeration:
0b0 : DISABLE
disable open load detection
0b1 : ENABLE
enable open load detection
End of enumeration elements list.
HS1_CYC_ON_ACTIVE : High Side 1 Cyclic ON Driver
bits : 7 - 6 (0 bit)
access : read-write
Enumeration:
0b0 : OFF
Cyclic ON Driver OFF
0b1 : ON
Cyclic ON Driver ON
End of enumeration elements list.
HS1_SRCTL_SEL : High Side 1 Slew Rate Control select
bits : 8 - 7 (0 bit)
access : read-write
Enumeration:
0b0 : Slew Rate 1
Slew Rate 10V/us is enabled
0b1 : Slew Rate 2
Slew Rate 30V/us is enabled
End of enumeration elements list.
HS1_OC_SEL : High Side 1 Overcurrent Threshold Selection
bits : 12 - 12 (1 bit)
access : read-write
Enumeration:
0x0 : IOCTH0
25 mA min.
0x1 : IOCTH1
50 mA min.
0x2 : IOCTH2
100 mA min.
0x3 : IOCTH3
150 mA min.
End of enumeration elements list.
HS2_EN : High Side 2 Enable
bits : 16 - 15 (0 bit)
access : read-write
Enumeration:
0b0 : DISABLE
HS circuit power off
0b1 : ENABLE
HS circuit power on
End of enumeration elements list.
HS2_PWM : High Side 2 PWM Enable
bits : 17 - 16 (0 bit)
access : read-write
Enumeration:
0b0 : DISABLE
disables control by PWM input
0b1 : ENABLE
enables control by PWM input
End of enumeration elements list.
HS2_ON : High Side 2 On
bits : 18 - 17 (0 bit)
access : read-write
Enumeration:
0b0 : OFF
HS driver off
0b1 : ON
HS driver on
End of enumeration elements list.
HS2_OL_EN : High Side 2 Open Load Detection Enable
bits : 19 - 18 (0 bit)
access : read-write
Enumeration:
0b0 : DISABLE
disable open load detection
0b1 : ENABLE
enable open load detection
End of enumeration elements list.
HS2_CYC_ON_ACTIVE : High Side 2 Cyclic ON Driver
bits : 23 - 22 (0 bit)
access : read-write
Enumeration:
0b0 : OFF
Cyclic ON Driver OFF
0b1 : ON
Cyclic ON Driver ON
End of enumeration elements list.
HS2_SRCTL_SEL : High Side 2 Slew Rate Control select
bits : 24 - 23 (0 bit)
access : read-write
Enumeration:
0b0 : Slew Rate 1
Slew Rate 10V/us is enabled
0b1 : Slew Rate 2
Slew Rate 30V/us is enabled
End of enumeration elements list.
HS2_OC_SEL : High Side 2 Overcurrent Threshold Selection
bits : 28 - 28 (1 bit)
access : read-write
Enumeration:
0x0 : IOCTH0
25 mA min.
0x1 : IOCTH1
50 mA min.
0x2 : IOCTH2
100 mA min.
0x3 : IOCTH3
150 mA min.
End of enumeration elements list.
High Side Driver Interrupt Status
address_offset : 0x8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
HS1_OT_IS : High Side 1 Overtemperature Interrupt Status
bits : 5 - 4 (0 bit)
access : read-write
Enumeration:
0b0 : no Overtemperature
no overtemperature occurred.
0b1 : Overtemperature
overtemperature occurred switch is automatically shutdown. Write sets status
End of enumeration elements list.
HS1_OL_IS : High Side 1 Open Load Interrupt Status
bits : 6 - 5 (0 bit)
access : read-write
Enumeration:
0b0 : NORMAL
normal load
0b1 : OPEN LOAD
open load detected, write sets status
End of enumeration elements list.
HS1_OC_IS : High Side 1 Overcurrent Interrupt Status
bits : 7 - 6 (0 bit)
access : read-write
Enumeration:
0b0 : no Overcurrent
no overcurrent Condition occurred.
0b1 : Overcurrent
overcurrent occurred switch is automatically shutdown. Write sets status.
End of enumeration elements list.
HS1_OT_STS : High Side 1 Overtemperature Status
bits : 13 - 12 (0 bit)
access : read-write
Enumeration:
0b0 : no Overtemperature
no overtemperature occurred.
0b1 : Overtemperature
overtemperature occurred switch is automatically shutdown. Write sets status.
End of enumeration elements list.
HS1_OL_STS : High Side 1 Open Load Interrupt Status
bits : 14 - 13 (0 bit)
access : read-write
Enumeration:
0b0 : no Open Load
no open load Condition occurred.
0b1 : Open Load
open load occurred switch is not automatically shutdown. Write sets status.
End of enumeration elements list.
HS2_OT_IS : High Side 2 Overtemperature Interrupt Status
bits : 21 - 20 (0 bit)
access : read-write
Enumeration:
0b0 : no Overtemperature
no overtemperature occurred.
0b1 : Overtemperature
overtemperature occurred switch is automatically shutdown. Write sets status
End of enumeration elements list.
HS2_OL_IS : High Side 2 Open Load Interrupt Status
bits : 22 - 21 (0 bit)
access : read-write
Enumeration:
0b0 : NORMAL
normal load
0b1 : OPEN LOAD
open load detected, write sets status
End of enumeration elements list.
HS2_OC_IS : High Side 2 Overcurrent Interrupt Status
bits : 23 - 22 (0 bit)
access : read-write
Enumeration:
0b0 : no Overcurrent
no overcurrent Condition occurred.
0b1 : Overcurrent
overcurrent occurred switch is automatically shutdown. Write sets status.
End of enumeration elements list.
HS2_OT_STS : High Side 2 Overtemperature Status
bits : 29 - 28 (0 bit)
access : read-write
Enumeration:
0b0 : no Overtemperature
no overtemperature occurred.
0b1 : Overtemperature
overtemperature occurred switch is automatically shutdown. Write sets status.
End of enumeration elements list.
HS2_OL_STS : High Side 2 Open Load Interrupt Status
bits : 30 - 29 (0 bit)
access : read-write
Enumeration:
0b0 : no Open Load
no open load Condition occurred.
0b1 : Open Load
open load occurred switch is not automatically shutdown. Write sets status.
End of enumeration elements list.
High Side Driver Interrupt Status Clear Register
address_offset : 0xC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
HS1_OT_ISC : High Side 1 Overtemperature Interrupt Status Clear
bits : 5 - 4 (0 bit)
access : write-only
Enumeration:
0b0 : no Clear
None
0b1 : Clear
None
End of enumeration elements list.
HS1_OL_ISC : High Side 1 Open Load Interrupt Status Clear
bits : 6 - 5 (0 bit)
access : write-only
Enumeration:
0b0 : no Clear
None
0b1 : Clear
None
End of enumeration elements list.
HS1_OC_ISC : High Side 1 Overcurrent Interrupt Status Clear
bits : 7 - 6 (0 bit)
access : write-only
Enumeration:
0b0 : no Clear
None
0b1 : Clear
None
End of enumeration elements list.
HS1_OT_SC : High Side 1 Overtemperature Status Clear
bits : 13 - 12 (0 bit)
access : write-only
Enumeration:
0b0 : no Clear
None
0b1 : Clear
None
End of enumeration elements list.
HS1_OL_SC : High Side 1 Open Load Status Clear
bits : 14 - 13 (0 bit)
access : write-only
Enumeration:
0b0 : no Clear
None
0b1 : Clear
None
End of enumeration elements list.
HS2_OT_ISC : High Side 2 Overtemperature Interrupt Status Clear
bits : 21 - 20 (0 bit)
access : write-only
Enumeration:
0b0 : no Clear
None
0b1 : Clear
None
End of enumeration elements list.
HS2_OL_ISC : High Side 2 Open Load Interrupt Status Clear
bits : 22 - 21 (0 bit)
access : write-only
Enumeration:
0b0 : no Clear
None
0b1 : Clear
None
End of enumeration elements list.
HS2_OC_ISC : High Side 2 Overcurrent Interrupt Status Clear
bits : 23 - 22 (0 bit)
access : write-only
Enumeration:
0b0 : no Clear
None
0b1 : Clear
None
End of enumeration elements list.
HS2_OT_SC : High Side 2 Overtemperature Status Clear
bits : 29 - 28 (0 bit)
access : write-only
Enumeration:
0b0 : no Clear
None
0b1 : Clear
None
End of enumeration elements list.
HS2_OL_SC : High Side 2 Open Load Status Clear
bits : 30 - 29 (0 bit)
access : write-only
Enumeration:
0b0 : no Clear
None
0b1 : Clear
None
End of enumeration elements list.
Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !
This website is sponsored by Embeetle, an IDE designed from scratch for embedded software developers.