Embeetle, an IDE designed from scratch for embedded software developers.address_offset : 0x0 Bytes (0x0)
size : 0xC00 byte (0x0)
mem_usage : registers
protection : not protected
Out Of Range Comparator Control Register
address_offset : 0x0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
ENORC0 : Enable Out of Range Comparator 0
bits : 0 - -1 (0 bit)
access : read-write
Enumeration:
#0 : value1
Out of range comparator disabled.
#1 : value2
Out of range comparator enabled.
End of enumeration elements list.
ENORC1 : Enable Out of Range Comparator 1
bits : 1 - 0 (0 bit)
access : read-write
Enumeration:
#0 : value1
Out of range comparator disabled.
#1 : value2
Out of range comparator enabled.
End of enumeration elements list.
ENORC2 : Enable Out of Range Comparator 2
bits : 2 - 1 (0 bit)
access : read-write
Enumeration:
#0 : value1
Out of range comparator disabled.
#1 : value2
Out of range comparator enabled.
End of enumeration elements list.
ENORC3 : Enable Out of Range Comparator 3
bits : 3 - 2 (0 bit)
access : read-write
Enumeration:
#0 : value1
Out of range comparator disabled.
#1 : value2
Out of range comparator enabled.
End of enumeration elements list.
ENORC4 : Enable Out of Range Comparator 4
bits : 4 - 3 (0 bit)
access : read-write
Enumeration:
#0 : value1
Out of range comparator disabled.
#1 : value2
Out of range comparator enabled.
End of enumeration elements list.
ENORC5 : Enable Out of Range Comparator 5
bits : 5 - 4 (0 bit)
access : read-write
Enumeration:
#0 : value1
Out of range comparator disabled.
#1 : value2
Out of range comparator enabled.
End of enumeration elements list.
ENORC6 : Enable Out of Range Comparator 6
bits : 6 - 5 (0 bit)
access : read-write
Enumeration:
#0 : value1
Out of range comparator disabled.
#1 : value2
Out of range comparator enabled.
End of enumeration elements list.
ENORC7 : Enable Out of Range Comparator 7
bits : 7 - 6 (0 bit)
access : read-write
Enumeration:
#0 : value1
Out of range comparator disabled.
#1 : value2
Out of range comparator enabled.
End of enumeration elements list.
CNF0 : Out of Range Comparator Flag 0
bits : 16 - 15 (0 bit)
access : read-write
Enumeration:
#0 : value1
Falling edge trigger out of range event register.
#1 : value2
Rising edge trigger out of range event register.
End of enumeration elements list.
CNF1 : Out of Range Comparator Flag 1
bits : 17 - 16 (0 bit)
access : read-write
Enumeration:
#0 : value1
Falling edge trigger out of range event register.
#1 : value2
Rising edge trigger out of range event register.
End of enumeration elements list.
CNF2 : Out of Range Comparator Flag 2
bits : 18 - 17 (0 bit)
access : read-write
Enumeration:
#0 : value1
Falling edge trigger out of range event register.
#1 : value2
Rising edge trigger out of range event register.
End of enumeration elements list.
CNF3 : Out of Range Comparator Flag 3
bits : 19 - 18 (0 bit)
access : read-write
Enumeration:
#0 : value1
Falling edge trigger out of range event register.
#1 : value2
Rising edge trigger out of range event register.
End of enumeration elements list.
CNF4 : Out of Range Comparator Flag 4
bits : 20 - 19 (0 bit)
access : read-write
Enumeration:
#0 : value1
Falling edge trigger out of range event register.
#1 : value2
Rising edge trigger out of range event register.
End of enumeration elements list.
CNF5 : Out of Range Comparator Flag 5
bits : 21 - 20 (0 bit)
access : read-write
Enumeration:
#0 : value1
Falling edge trigger out of range event register.
#1 : value2
Rising edge trigger out of range event register.
End of enumeration elements list.
CNF6 : Out of Range Comparator Flag 6
bits : 22 - 21 (0 bit)
access : read-write
Enumeration:
#0 : value1
Falling edge trigger out of range event register.
#1 : value2
Rising edge trigger out of range event register.
End of enumeration elements list.
CNF7 : Out of Range Comparator Flag 7
bits : 23 - 22 (0 bit)
access : read-write
Enumeration:
#0 : value1
Falling edge trigger out of range event register.
#1 : value2
Rising edge trigger out of range event register.
End of enumeration elements list.
Analog Comparator 0 Control Register
address_offset : 0xB5C Bytes (0x0)
size : 16 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
CMP_EN : Comparator enable
bits : 0 - -1 (0 bit)
access : read-write
Enumeration:
#0 : value1
Comparator is disabled
#1 : value2
Comparator is enabled
End of enumeration elements list.
CMP_FLT_OFF : Disables comparator filter
bits : 1 - 0 (0 bit)
access : read-write
Enumeration:
#0 : value1
filter is active
#1 : value2
filter is switched off (to prevent a filter delay)
End of enumeration elements list.
CMP_INV_OUT : Inverted Comparator output
bits : 3 - 2 (0 bit)
access : read-write
Enumeration:
#0 : value1
no inversion of comparator signal
#1 : value2
comparator signal is inverted
End of enumeration elements list.
CMP_HYST_ADJ : Comparator hysteresis adjust
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#00 : value1
Comparator hysteresis is switched off
#01 : value2
Hysteresis_typ = 10mV
#10 : value3
Hysteresis_typ = 15mV
#11 : value4
Hysteresis_typ = 20mV
End of enumeration elements list.
ACMP0_SEL : Connect ACMP0.INP to ACMP1.INP
bits : 6 - 5 (0 bit)
access : read-write
Enumeration:
#0 : value1
ACMP0.INP is not connected
#1 : value2
ACMP0.INP is connected to ACMP1.INP
End of enumeration elements list.
CMP_LPWR : Low Power Mode
bits : 8 - 7 (0 bit)
access : read-write
Enumeration:
#0 : value1
High Power Mode
#1 : value2
Low Power Mode
End of enumeration elements list.
CMP_OUT : Comparator output monitor bit
bits : 15 - 14 (0 bit)
access : read-only
Enumeration:
#0 : value1
state "Vminus > Vplus"
#1 : value2
state "Vminus < Vplus"
End of enumeration elements list.
Analog Comparator 1 Control Register
address_offset : 0xB60 Bytes (0x0)
size : 16 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
CMP_EN : Comparator enable
bits : 0 - -1 (0 bit)
access : read-write
Enumeration:
#0 : value1
Comparator is disabled
#1 : value2
Comparator is enabled
End of enumeration elements list.
CMP_FLT_OFF : Disables comparator filter
bits : 1 - 0 (0 bit)
access : read-write
Enumeration:
#0 : value1
filter is active
#1 : value2
filter is switched off (to prevent a filter delay)
End of enumeration elements list.
CMP_INV_OUT : Inverted Comparator output
bits : 3 - 2 (0 bit)
access : read-write
Enumeration:
#0 : value1
no inversion of comparator signal
#1 : value2
comparator signal is inverted
End of enumeration elements list.
CMP_HYST_ADJ : Comparator hysteresis adjust
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#00 : value1
Comparator hysteresis is switched off
#01 : value2
Hysteresis_typ = 10mV
#10 : value3
Hysteresis_typ = 15mV
#11 : value4
Hysteresis_typ = 20mV
End of enumeration elements list.
REF_DIV_EN : Resistor Divider is enabled and Reference Voltage is applied to ACMP1
bits : 6 - 5 (0 bit)
access : read-write
Enumeration:
#0 : value1
no resistor is connected
#1 : value2
the divider resistor is enabled and the voltage is applied to ACMP1.INP
End of enumeration elements list.
CMP_OUT : Comparator output monitor bit
bits : 15 - 14 (0 bit)
access : read-only
Enumeration:
#0 : value1
state "Vminus > Vplus"
#1 : value2
state "Vminus < Vplus"
End of enumeration elements list.
Analog Comparator 2 Control Register
address_offset : 0xB64 Bytes (0x0)
size : 16 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
CMP_EN : Comparator enable
bits : 0 - -1 (0 bit)
access : read-write
Enumeration:
#0 : value1
Comparator is disabled
#1 : value2
Comparator is enabled
End of enumeration elements list.
CMP_FLT_OFF : Disables comparator filter
bits : 1 - 0 (0 bit)
access : read-write
Enumeration:
#0 : value1
filter is active
#1 : value2
filter is switched off (to prevent a filter delay)
End of enumeration elements list.
CMP_INV_OUT : Inverted Comparator output
bits : 3 - 2 (0 bit)
access : read-write
Enumeration:
#0 : value1
no inversion of comparator signal
#1 : value2
comparator signal is inverted
End of enumeration elements list.
CMP_HYST_ADJ : Comparator hysteresis adjust
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#00 : value1
Comparator hysteresis is switched off
#01 : value2
Hysteresis_typ = 10mV
#10 : value3
Hysteresis_typ = 15mV
#11 : value4
Hysteresis_typ = 20mV
End of enumeration elements list.
ACMP2_SEL : Connect ACMP2.INP to ACMP1.INP
bits : 6 - 5 (0 bit)
access : read-write
Enumeration:
#0 : value1
ACMP2.INP is not connected
#1 : value2
ACMP2.INP is connected to ACMP1.INP
End of enumeration elements list.
CMP_OUT : Comparator output monitor bit
bits : 15 - 14 (0 bit)
access : read-only
Enumeration:
#0 : value1
state "Vminus > Vplus"
#1 : value2
state "Vminus < Vplus"
End of enumeration elements list.
Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !
This website is sponsored by Embeetle, an IDE designed from scratch for embedded software developers.