Embeetle, an IDE designed from scratch for embedded software developers.address_offset : 0x0 Bytes (0x0)
size : 0x50 byte (0x0)
mem_usage : registers
protection : not protected
Port 2 ADC Selection Control Register
address_offset : 0x0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
P2_0_ADC_SEL : Port 2.0 Input Selection
bits : 0 - -1 (0 bit)
access : read-write
Enumeration:
0b0 : ADC10B
Port 2.0 is connected to Channel 0 of ADC10B
0b1 : ADC3
Port 2.0 is connected to IN_P of ADC3
End of enumeration elements list.
P2_2_ADC_SEL : Port 2.2 Input Selection
bits : 1 - 0 (0 bit)
access : read-write
Enumeration:
0b0 : ADC10B
Port 2.2 is connected to Channel 2 of ADC10B
0b1 : ADC3
Port 2.2 is connected to IN_N of ADC3
End of enumeration elements list.
P2_3_ADC_SEL : Port 2.3 Input Selection
bits : 2 - 1 (0 bit)
access : read-write
Enumeration:
0b0 : ADC1.Ch3
Port 2.3 is connected to ADC1.Ch3
0b1 : none
ADC1.Ch3 disconnected from P2.3
End of enumeration elements list.
P2_4_ADC_SEL : Port 2.4 Input Selection
bits : 3 - 2 (0 bit)
access : read-write
Enumeration:
0b0 : ADC10B
Port 2.4 is connected to Channel 4 of ADC10B
0b1 : ADC4
.
End of enumeration elements list.
P2_5_ADC_SEL : Port 2.5 Input Selection
bits : 4 - 3 (0 bit)
access : read-write
Enumeration:
0b0 : ADC10B
Port 2.5 is connected to Channel 5 of ADC10B
0b1 : ADC4
.
End of enumeration elements list.
ADC3_INP_SEL : ADC3 Positive Input Selection
bits : 8 - 7 (0 bit)
access : read-write
Enumeration:
0b0 : none
ADC3.P input disconnected
0b1 : Mux-Port 2.0
Port 2.0 multiplexer is connected to ADC3.P
End of enumeration elements list.
ADC3_INN_SEL : ADC3 Negative Input Selection
bits : 9 - 8 (0 bit)
access : read-write
Enumeration:
0b0 : none
ADC3.N input disconnected
0b1 : Mux-Port 2.2
Port 2.2 multiplexer is connected to ADC2.N
End of enumeration elements list.
ADC1_CH1_SEL : ADC1 Channel 1 Input Selection
bits : 10 - 9 (0 bit)
access : read-write
Enumeration:
0b0 : none
Current Sense Amplifier disconnected from ADC1.Ch1
0b1 : CS_AMP
Current Sense Amplifier is conncted to Ch1 of ADC1
End of enumeration elements list.
Temperature Sensor Control Register
address_offset : 0x10 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PMU_OTWARN_STS : PMU Regulator Overtemperature Warning (MU) Status
bits : 4 - 3 (0 bit)
access : read-only
Enumeration:
0b0 : INACTIVE
write clears status
0b1 : ACTIVE
interrupt status set
End of enumeration elements list.
PMU_OT_STS : PMU Regulator Overtemperature (MU) Status
bits : 5 - 4 (0 bit)
access : read-only
Enumeration:
0b0 : INACTIVE
write clears status
0b1 : ACTIVE
interrupt status set
End of enumeration elements list.
SYS_OTWARN_STS : System Overtemperature Warning (MU) Status
bits : 6 - 5 (0 bit)
access : read-only
Enumeration:
0b0 : INACTIVE
write clears status
0b1 : ACTIVE
interrupt status set
End of enumeration elements list.
SYS_OT_STS : System Overtemperature (MU) Status
bits : 7 - 6 (0 bit)
access : read-only
Enumeration:
0b0 : INACTIVE
write clears status
0b1 : ACTIVE
interrupt status set
End of enumeration elements list.
Reference 1 Status Register
address_offset : 0x14 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
REFBG_LOTHWARN_STS : Status for Undervoltage Threshold Measurement of internal VAREF
bits : 4 - 3 (0 bit)
access : read-only
Enumeration:
0b0 : UPPER_TRIG_RESET
write clears status
0b1 : UPPER_TRIG_SET
trigger status set
End of enumeration elements list.
REFBG_UPTHWARN_STS : Status for Overvoltage Threshold Measurement of internal VAREF
bits : 5 - 4 (0 bit)
access : read-only
Enumeration:
0b0 : UPPER_TRIG_RESET
write clears status
0b1 : UPPER_TRIG_SET
trigger status set
End of enumeration elements list.
Reference 2 Control Register
address_offset : 0x18 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
VREF5V_PD_N : ADC1 Bit Reference Voltage Generation Power Down Bit
bits : 0 - -1 (0 bit)
access : read-write
Enumeration:
0b0 : DISABLED
Power Down
0b1 : ACTIVE
no Power Down
End of enumeration elements list.
VREF5V_OVL_STS : ADC1 Bit Reference Voltage Generation Over Load Bit
bits : 1 - 0 (0 bit)
access : read-only
Enumeration:
0b0 : no_OVERLOAD
no OVERLOAD detected
0b1 : OVERLOAD
OVERLOAD detected
End of enumeration elements list.
VREF5V_UV_STS : ADC1 Bit Reference Voltage Generation Undervoltage Bit
bits : 2 - 1 (0 bit)
access : read-only
Enumeration:
0b0 : no_Undervoltage
no Undervoltage detected
0b1 : Undervoltage
Undervoltage detected
End of enumeration elements list.
VREF5V_OV_STS : ADC1 Bit Reference Voltage Generation Overvoltage Bit
bits : 3 - 2 (0 bit)
access : read-only
Enumeration:
0b0 : no_Overvoltage
no Overvoltage detected
0b1 : Overvoltage
Overvoltage detected
End of enumeration elements list.
Trimming of Driver
address_offset : 0x20 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
BEMF_BT_TFILT_SEL : Blanking Time for BEMF Comparator Output Signal
bits : 0 - 1 (2 bit)
access : read-write
Enumeration:
0b000 : 6_us
6 us filter time
0b001 : 8_us
8 us filter time
0b010 : 12_us
12 us filter time
0b011 : 16_us
16 us filter time
0b101 : 3_us
3 us filter time
End of enumeration elements list.
BEMF_GPT_CAPIN_SEL : GPT12 CAPIN input selector
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
0b00 : SWTRIG
software trigger
0b01 : Phase_U
trigger from Phase U
0b10 : Phase_V
trigger from Phase V
0b11 : Phase_W
trigger from Phase W
End of enumeration elements list.
BEMF_TFILT_SEL : Filter Time for BEMF Comparator Output Signal
bits : 8 - 8 (1 bit)
access : read-write
Enumeration:
0b00 : 1_us
1 us filter time
0b01 : 2_us
2 us filter time
0b10 : 4_us
4 us filter time
0b11 : 8_us
8 us filter time
End of enumeration elements list.
Supply Sense Control Register
address_offset : 0x4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
VMON_SEN_PD_N : Monitoring Input Attenuator enable
bits : 0 - -1 (0 bit)
access : read-write
Enumeration:
0b0 : DISABLE
Attenuator switched off
0b1 : ENABLE
Attenuator switched on
End of enumeration elements list.
VMON_SEN_HRESO_5V : Monitoring Input Attenuator High Impedance Output Control
bits : 4 - 3 (0 bit)
access : read-write
Enumeration:
0b0 : High_Resistive_Output_Disable
Connection to ADC input low ohmic
0b1 : High_Resistive_Output_Enable
Connection to ADC input high ohmic
End of enumeration elements list.
VMON_SEN_SEL_INRANGE : Monitoring Input Attenuator Select Inputrange
bits : 5 - 4 (0 bit)
access : read-write
Enumeration:
0b0 : range0
0-18V range is selected
0b1 : range1
0-28V range is selected
End of enumeration elements list.
BEMF Comparator Control Status Register
address_offset : 0x8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PHUCOMP_EN : Phase U Comparator enable
bits : 0 - -1 (0 bit)
access : read-write
Enumeration:
0b0 : DISABLE
Comparator is disabled
0b1 : ENABLE
Comparator is enabled
End of enumeration elements list.
PHVCOMP_EN : Phase V Comparator enable
bits : 1 - 0 (0 bit)
access : read-write
Enumeration:
0b0 : DISABLE
Comparator is disabled
0b1 : ENABLE
Comparator is enabled
End of enumeration elements list.
PHWCOMP_EN : Phase W Comparator enable
bits : 2 - 1 (0 bit)
access : read-write
Enumeration:
0b0 : DISABLE
Comparator is disabled
0b1 : ENABLE
Comparator is enabled
End of enumeration elements list.
DEMGFILTDIS : BEMF Comparator Demagnetisation (Demag) Filter Disable
bits : 3 - 2 (0 bit)
access : read-write
Enumeration:
0b0 : ENABLED
BEMF Comparator Demag Filter enabled
0b1 : DISABLED
BEMF Comparator Demag Filter disabled
End of enumeration elements list.
FILTBYPS : BEMF Comparator Output Filter Bypass
bits : 4 - 3 (0 bit)
access : read-write
Enumeration:
0b0 : ENABLED
BEMF Comparator Output Filter enabled
0b1 : DISABLED
BEMF Comparator Output Filter disabled
End of enumeration elements list.
GPT12CAPINSW : GPT12 CAPIN software trigger
bits : 5 - 4 (0 bit)
access : read-write
Enumeration:
0b0 : Value0
software trigger reset
0b1 : Value1
software trigger set
End of enumeration elements list.
PHUCOMP_ON : Phase U Comparator on
bits : 8 - 7 (0 bit)
access : read-write
Enumeration:
0b0 : DISABLE
Comparator is switched off
0b1 : ENABLE
Comparator is switched on
End of enumeration elements list.
PHVCOMP_ON : Phase V Comparator on
bits : 9 - 8 (0 bit)
access : read-write
Enumeration:
0b0 : DISABLE
Comparator is switched off
0b1 : ENABLE
Comparator is switched on
End of enumeration elements list.
PHWCOMP_ON : Phase W Comparator on
bits : 10 - 9 (0 bit)
access : read-write
Enumeration:
0b0 : DISABLE
Comparator is switched off
0b1 : ENABLE
Comparator is switched on
End of enumeration elements list.
CCPOS_INSEL : CCPOSx_3 INSEL select, x = 0,1,2
bits : 12 - 11 (0 bit)
access : read-write
Enumeration:
0b0 : GPIO
GPIO selected
0b1 : BEMF
BEMF selected
End of enumeration elements list.
PHU_ZC_STS : Phase U Comparator zero crossing status
bits : 16 - 15 (0 bit)
access : read-only
Enumeration:
0b0 : Below_Threshold
zero crossing comparator input is below threshold
0b1 : Above_Threshold
zero crossing comparator input is above threshold
End of enumeration elements list.
PHV_ZC_STS : Phase V Comparator zero crossing status
bits : 17 - 16 (0 bit)
access : read-only
Enumeration:
0b0 : Below_Threshold
zero crossing comparator input is below threshold
0b1 : Above_Threshold
zero crossing comparator input is above threshold
End of enumeration elements list.
PHW_ZC_STS : Phase W Comparator zero crossing status
bits : 18 - 17 (0 bit)
access : read-only
Enumeration:
0b0 : Below_Threshold
zero crossing comparator input is below threshold
0b1 : Above_Threshold
zero crossing comparator input is above threshold
End of enumeration elements list.
Current Sense Amplifier Control Register
address_offset : 0xC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EN : OPA enable
bits : 0 - -1 (0 bit)
access : read-write
Enumeration:
0b0 : DISABLE
OPA switched off
0b1 : ENABLE
OPA switched on
End of enumeration elements list.
GAIN : OPA gain setting
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
0x0 : value_0
Gain_10
0x1 : value_1
Gain_20
0x2 : value_2
Gain_40
0x3 : value_3
Gain_60
End of enumeration elements list.
VZERO : Current Sense Output Voltage Level to Ground
bits : 8 - 7 (0 bit)
access : read-write
Enumeration:
0b0 : VOUT
Output Voltage is VOUT of Amplifier
0b1 : GROUND
Output Voltage is Ground of Feedback Network
End of enumeration elements list.
Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !
This website is sponsored by Embeetle, an IDE designed from scratch for embedded software developers.