TCSR2

TCAP2

TEXCON2

TEXISR2

TCSR3

TCMPR3

TISR3

TDR3

TCAP3

TEXCON3

TEXISR3

TCMPR2

TISR2

TDR2

PRESCALE : Pre-scale Counter
bits : 0 - 7 (8 bit)
access : read-write

TDR_EN : Data Load Enable\nWhen this bit is set, timer counter value (TDR) will be updated continuously to monitor internal 24-bit up counter value as the counter is counting.
bits : 16 - 16 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

CTB : Counter Mode Enable Bit \nThis bit is for external counting pin function enabled. When timer is used as an event counter, this bit should be set to 1 and select HCLK as timer clock source. Please refer to 10.4.5 for detail description.
bits : 24 - 24 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

CACT : Timer Active Status Bit (Read Only)\nThis bit indicates the 24-bit up counter status.
bits : 25 - 25 (1 bit)
access : read-only

Enumeration:

End of enumeration elements list.

CRST : Timer Reset Bit\nSetting this bit will reset the 24-bit up counter value (TDR) and also force CEN (TCSR[30] timer enable bit) to 0 if CACT (TCSR[25] timer active status bit) is 1.
bits : 26 - 26 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

MODE : Timer Operating Mode
bits : 27 - 28 (2 bit)
access : read-write

IE : Interrupt Enable Bit\nIf this bit is enabled, when the timer interrupt flag (TISR[0] TIF) is set to 1, the timer interrupt signal is generated and inform to CPU.
bits : 29 - 29 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

CEN : Timer Enable Bit
bits : 30 - 30 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

DBGACK_TMR : ICE Debug Mode Acknowledge Disable (Write-protection Bit)\nTIMER counter will keep going no matter CPU is held by ICE or not.
bits : 31 - 31 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

TCAP : Timer Capture Data Register When TEXEN (TEXCON[3] timer external pin enable) bit is set, RSTCAPSEL (TEXCON[4] timer external reset counter/capture mode select) bit is 0, and a transition on TMx pin matched the TEX_EDGE (TEXCON[2:1] timer external pin edge detect) setting, TEXIF (TEXISR[0] timer external interrupt flag) will set to 1 and the current timer counter value (TDR value) will be auto-loaded into this TCAP field.
bits : 0 - 23 (24 bit)
access : read-only

TX_PHASE : Timer External Count Phase \nThis bit indicates the detection phase of external counting pin.
bits : 0 - 0 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

TEX_EDGE : Timer External Pin Edge Detect
bits : 1 - 2 (2 bit)
access : read-write

Enumeration:

End of enumeration elements list.

TEXEN : Timer External Pin Enable\nThis bit enables the RSTCAPSEL (TEXCON[4] timer external reset counter/capture mode select ) function on the TMx pin.
bits : 3 - 3 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

RSTCAPSEL : Timer External Reset Counter / Capture Mode Select
bits : 4 - 4 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

TEXIEN : Timer External interrupt Enable
bits : 5 - 5 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

TEXDB : Timer External Capture pin De-bounce Enable \nIf this bit is enabled, the edge detection of TMx pin is detected with de-bounce circuit.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

TCDB : Timer Counter pin De-bounce Enable\nIf this bit is enabled, the edge detection of TMx pin is detected with de-bounce circuit.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

TEXIF : Timer External Interrupt Flag This bit indicates the timer external interrupt flag status. When TEXEN (TEXCON[3] timer external pin enable) bit is set, RSTCAPSEL (TEXCON[4] timer external reset counter/capture mode select) bit is 0, and a transition on TMx pin matched the TEX_EDGE (TEXCON[2:1] timer external pin edge detect) setting, this bit will set to 1 by hardware. And it is cleared by software writing 1 to this bit.
bits : 0 - 0 (1 bit)
access : read-write

TCMP : Timer Compared Value\nTCMP is a 24-bit compared value register. When the internal 24-bit up counter value is equal to TCMP value, the TIF (TISR[0] timet interrupt flag) will set to 1.\nNote1: Never write 0x0 or 0x1 in TCMP field, or the core will run into unknown state.\nNote2: When timer is operating at continuous counting mode, the 24-bit up counter will keep counting continuously even if software writes a new value into TCMP field. But if timer is operating at other modes, the 24-bit up counter will restart counting and using newest TCMP value to be the timer compared value if software writes a new value into TCMP field.
bits : 0 - 23 (24 bit)
access : read-write

TIF : Timer Interrupt Flag\nThis bit indicates the interrupt flag status of Timer.\nAnd this bit is set by hardware when the timer counter value) matches the timer compared value (TCMP value). It is cleared by software writing 1 to this bit.
bits : 0 - 0 (1 bit)
access : read-write

TDR : Timer Data Register\nIf TDR_EN (TCSR[16]) is set to 1, TDR will be updated continuously to monitor 24-bit timer counter value.
bits : 0 - 23 (24 bit)
access : read-only