Embeetle, an IDE designed from scratch for embedded software developers.address_offset : 0x0 Bytes (0x0)
size : 0x10 byte (0x0)
mem_usage : registers
protection : not protected
Analog Comparator 0 Control Register
address_offset : 0x0 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
ACMP0_EN : Analog Comparator 0 Enable\nComparator output need wait stable 10 us after ACMP0_EN is set.
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
ACMPIE0 : Analog Comparator 0 Interrupt Enable
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Interrupt function Disabled
#1 : 1
Interrupt function Enabled
End of enumeration elements list.
ACMP0_HYS_EN : CMP Hysteresis Enable
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Hysteresis function Disabled (Default).
#1 : 1
Hysteresis function Enabled. The typical range is 20mV
End of enumeration elements list.
CP0 : Analog Comparator 0 positive input select
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
The comparator reference pin P8.4/CPP0 is selected as the positive comparator input
#1 : 1
The internal OP amplifier 0 output is selected as the positive comparator input
End of enumeration elements list.
CN0 : Analog Comparator 0 negative input select
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
The comparator reference pin P8.3/CPN0 is selected as the negative comparator input
#1 : 1
The internal comparator reference voltage (Vref=1.2V) is selected as the negative comparator input
End of enumeration elements list.
ACMP0INV : Analog Comparator 0 output inverse select
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
The comparator output inverse function Disabled
#1 : 1
The comparator output inverse function Enabled
End of enumeration elements list.
Analog Comparator 1 Control Register
address_offset : 0x4 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
ACMP1_EN : Analog Comparator 1 Enable\nComparator output need wait stable 10 us after ACMP1_EN is set.
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
ACMPIE1 : Analog Comparator 1 Interrupt Enable
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Interrupt function Disabled
#1 : 1
Interrupt function Enabled
End of enumeration elements list.
ACMP1_HYS_EN : CMP Hysteresis Enable
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Hysteresis function Disabled (Default).
#1 : 1
Hysteresis function Enabled. The typical range is 20mV
End of enumeration elements list.
CP1 : Analog Comparator 1 positive input select
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
The comparator reference pin P6.5/CPP1 is selected as the positive comparator input
#1 : 1
The internal OP amplifier 1 output is selected as the positive comparator input
End of enumeration elements list.
CN1 : Analog Comparator 1 negative input select
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
The comparator reference pin P6.4/CPN1 is selected as the negative comparator input
#1 : 1
The internal comparator reference voltage (Vref=1.2V) is selected as the negative comparator input
End of enumeration elements list.
ACMP1INV : Analog Comparator 1 output inverse select
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
The comparator output inverse function Disabled
#1 : 1
The comparator output inverse function Enabled
End of enumeration elements list.
Analog Comparator 2 Control Register
address_offset : 0x8 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
ACMP2_EN : Analog Comparator 2 Enable\nComparator output need wait stable 10 us after ACMP2_EN is first set.
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
ACMPIE2 : Analog Comparator 2 Interrupt Enable
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Interrupt function Disabled
#1 : 1
Interrupt function Enabled
End of enumeration elements list.
ACMP2_HYS_EN : CMP Hysteresis Enable
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Hysteresis function Disabled (Default).
#1 : 1
Hysteresis function Enabled. The typical range is 20mV
End of enumeration elements list.
CN2 : Analog Comparator 2 negative input select
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
The comparator reference pin P7.4/CPN2 is selected as the negative comparator input
#1 : 1
The internal comparator reference voltage (Vref=1.2V) is selected as the negative comparator input
End of enumeration elements list.
ACMP2INV : Analog Comparator 2 output inverse select
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
The comparator output inverse function Disabled
#1 : 1
The comparator output inverse function Enabled
End of enumeration elements list.
Analog Comparator Status Register
address_offset : 0xC Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
ACMPF0 : Compare 0 Flag\nThis bit is set by hardware whenever the comparator 0 output changes state. This will cause an interrupt if ACMPCR0[1] is set to 1.\nWrite 1 to clear this bit to 0.
bits : 0 - 0 (1 bit)
access : read-write
ACMPF1 : Compare 1 Flag\nThis bit is set by hardware whenever the comparator 1 output changes state. This will cause an interrupt if ACMPCR1[1] is set to 1.\nWrite 1 to clear this bit to 0.
bits : 1 - 1 (1 bit)
access : read-write
ACMPF2 : Compare 2 Flag\nThis bit is set by hardware whenever the comparator 2 output changes state. This will cause an interrupt if ACMPCR2[1] is set to 1.\nWrite 1 to clear this bit to 0.
bits : 2 - 2 (1 bit)
access : read-write
CO0 : Compare 0 Output
bits : 8 - 8 (1 bit)
access : read-write
CO1 : Compare 1 Output
bits : 9 - 9 (1 bit)
access : read-write
CO2 : Compare 2 Output
bits : 10 - 10 (1 bit)
access : read-write
Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !
This website is sponsored by Embeetle, an IDE designed from scratch for embedded software developers.