\n
address_offset : 0x0 Bytes (0x0)
size : 0x2488 byte (0x0)
mem_usage : registers
protection : not protected
Byte pin registers for all port GPIO pins
address_offset : 0x0 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PBYTE : Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 0 (1 bit)
access : read-write
Byte pin registers for all port GPIO pins
address_offset : 0x1 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PBYTE : Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 0 (1 bit)
access : read-write
Word pin registers for all port GPIO pins
address_offset : 0x101A4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PWORD : Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 31 (32 bit)
access : read-write
Word pin registers for all port GPIO pins
address_offset : 0x111E0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PWORD : Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 31 (32 bit)
access : read-write
Byte pin registers for all port GPIO pins
address_offset : 0x114 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PBYTE : Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 0 (1 bit)
access : read-write
Word pin registers for all port GPIO pins
address_offset : 0x12220 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PWORD : Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 31 (32 bit)
access : read-write
Byte pin registers for all port GPIO pins
address_offset : 0x12C Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PBYTE : Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 0 (1 bit)
access : read-write
Word pin registers for all port GPIO pins
address_offset : 0x13264 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PWORD : Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 31 (32 bit)
access : read-write
Word pin registers for all port GPIO pins
address_offset : 0x142AC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PWORD : Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 31 (32 bit)
access : read-write
Byte pin registers for all port GPIO pins
address_offset : 0x145 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PBYTE : Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 0 (1 bit)
access : read-write
Byte pin registers for all port GPIO pins
address_offset : 0x15 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PBYTE : Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 0 (1 bit)
access : read-write
Word pin registers for all port GPIO pins
address_offset : 0x152F8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PWORD : Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 31 (32 bit)
access : read-write
Byte pin registers for all port GPIO pins
address_offset : 0x15F Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PBYTE : Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 0 (1 bit)
access : read-write
Word pin registers for all port GPIO pins
address_offset : 0x16348 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PWORD : Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 31 (32 bit)
access : read-write
Word pin registers for all port GPIO pins
address_offset : 0x1739C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PWORD : Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 31 (32 bit)
access : read-write
Byte pin registers for all port GPIO pins
address_offset : 0x17A Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PBYTE : Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 0 (1 bit)
access : read-write
Word pin registers for all port GPIO pins
address_offset : 0x183F4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PWORD : Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 31 (32 bit)
access : read-write
Word pin registers for all port GPIO pins
address_offset : 0x19450 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PWORD : Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 31 (32 bit)
access : read-write
Byte pin registers for all port GPIO pins
address_offset : 0x196 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PBYTE : Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 0 (1 bit)
access : read-write
Word pin registers for all port GPIO pins
address_offset : 0x1A4B0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PWORD : Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 31 (32 bit)
access : read-write
Byte pin registers for all port GPIO pins
address_offset : 0x1B3 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PBYTE : Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 0 (1 bit)
access : read-write
Word pin registers for all port GPIO pins
address_offset : 0x1B514 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PWORD : Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 31 (32 bit)
access : read-write
Byte pin registers for all port GPIO pins
address_offset : 0x1C Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PBYTE : Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 0 (1 bit)
access : read-write
Word pin registers for all port GPIO pins
address_offset : 0x1C57C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PWORD : Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 31 (32 bit)
access : read-write
Byte pin registers for all port GPIO pins
address_offset : 0x1D1 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PBYTE : Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 0 (1 bit)
access : read-write
Word pin registers for all port GPIO pins
address_offset : 0x1D5E8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PWORD : Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 31 (32 bit)
access : read-write
Word pin registers for all port GPIO pins
address_offset : 0x1E658 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PWORD : Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 31 (32 bit)
access : read-write
Byte pin registers for all port GPIO pins
address_offset : 0x1F0 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PBYTE : Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 0 (1 bit)
access : read-write
Word pin registers for all port GPIO pins
address_offset : 0x1F6CC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PWORD : Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 31 (32 bit)
access : read-write
Word pin registers for all port GPIO pins
address_offset : 0x2000 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PWORD : Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 31 (32 bit)
access : read-write
Word pin registers for all port GPIO pins
address_offset : 0x20744 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PWORD : Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 31 (32 bit)
access : read-write
Byte pin registers for all port GPIO pins
address_offset : 0x210 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PBYTE : Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 0 (1 bit)
access : read-write
Word pin registers for all port GPIO pins
address_offset : 0x217C0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PWORD : Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 31 (32 bit)
access : read-write
Word pin registers for all port GPIO pins
address_offset : 0x22840 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PWORD : Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 31 (32 bit)
access : read-write
Byte pin registers for all port GPIO pins
address_offset : 0x24 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PBYTE : Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 0 (1 bit)
access : read-write
Byte pin registers for all port GPIO pins
address_offset : 0x2D Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PBYTE : Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 0 (1 bit)
access : read-write
Byte pin registers for all port GPIO pins
address_offset : 0x3 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PBYTE : Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 0 (1 bit)
access : read-write
Word pin registers for all port GPIO pins
address_offset : 0x3004 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PWORD : Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 31 (32 bit)
access : read-write
Byte pin registers for all port GPIO pins
address_offset : 0x37 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PBYTE : Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 0 (1 bit)
access : read-write
Direction registers for all port GPIO pins
address_offset : 0x4000 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DIRP : Selects pin direction for pin PIOm_n (bit 0 = PIOn_0, bit 1 = PIOn_1, etc.). Supported pins depends on the specific device and package. 0 = input. 1 = output.
bits : 0 - 31 (32 bit)
access : read-write
Word pin registers for all port GPIO pins
address_offset : 0x400C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PWORD : Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 31 (32 bit)
access : read-write
Mask register for all port GPIO pins
address_offset : 0x4100 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MASKP : Controls which bits corresponding to PIOm_n are active in the MPORT register (bit 0 = PIOn_0, bit 1 = PIOn_1, etc.). Supported pins depends on the specific device and package.0 = Read MPORT: pin state; write MPORT: load output bit. 1 = Read MPORT: 0; write MPORT: output bit not affected.
bits : 0 - 31 (32 bit)
access : read-write
Byte pin registers for all port GPIO pins
address_offset : 0x42 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PBYTE : Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 0 (1 bit)
access : read-write
Port pin register for all port GPIO pins
address_offset : 0x4200 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PORT : Reads pin states or loads output bits (bit 0 = PIOn_0, bit 1 = PIOn_1, etc.). Supported pins depends on the specific device and package. 0 = Read: pin is low; write: clear output bit. 1 = Read: pin is high; write: set output bit.
bits : 0 - 31 (32 bit)
access : read-write
Masked port register for all port GPIO pins
address_offset : 0x4300 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MPORTP : Masked port register (bit 0 = PIOn_0, bit 1 = PIOn_1, etc.). Supported pins depends on the specific device and package. 0 = Read: pin is LOW and/or the corresponding bit in the MASK register is 1; write: clear output bit if the corresponding bit in the MASK register is 0. 1 = Read: pin is HIGH and the corresponding bit in the MASK register is 0; write: set output bit if the corresponding bit in the MASK register is 0.
bits : 0 - 31 (32 bit)
access : read-write
Write: Set register for port. Read: output bits for port
address_offset : 0x4400 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
SETP : Read or set output bits (bit 0 = PIOn_0, bit 1 = PIOn_1, etc.). Supported pins depends on the specific device and package. 0 = Read: output bit: write: no operation. 1 = Read: output bit; write: set output bit.
bits : 0 - 31 (32 bit)
access : read-write
Clear port for all port GPIO pins
address_offset : 0x4500 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
CLRP : Clear output bits (bit 0 = PIOn_0, bit 1 = PIOn_1, etc.). Supported pins depends on the specific device and package. 0 = No operation. 1 = Clear output bit.
bits : 0 - 31 (32 bit)
access : write-only
Toggle port for all port GPIO pins
address_offset : 0x4600 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
NOTP : Toggle output bits (bit 0 = PIOn_0, bit 1 = PIOn_1, etc.). Supported pins depends on the specific device and package. 0 = no operation. 1 = Toggle output bit.
bits : 0 - 31 (32 bit)
access : write-only
Set pin direction bits for port
address_offset : 0x4700 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
DIRSETP : Set direction bits (bit 0 = PIOn_0, bit 1 = PIOn_1, etc.). Supported pins depends on the specific device and package. 0 = No operation. 1 = Set direction bit.
bits : 0 - 31 (32 bit)
access : write-only
Clear pin direction bits for port
address_offset : 0x4800 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
DIRCLRP : Clear direction bits (bit 0 = PIOn_0, bit 1 = PIOn_1, etc.). Supported pins depends on the specific device and package. 0 = No operation. 1 = Clear direction bit.
bits : 0 - 31 (32 bit)
access : write-only
Toggle pin direction bits for port
address_offset : 0x4900 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
DIRNOTP : Toggle direction bits (bit 0 = PIOn_0, bit 1 = PIOn_1, etc.). Supported pins depends on the specific device and package. 0 = no operation. 1 = Toggle direction bit.
bits : 0 - 31 (32 bit)
access : write-only
Byte pin registers for all port GPIO pins
address_offset : 0x4E Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PBYTE : Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 0 (1 bit)
access : read-write
Word pin registers for all port GPIO pins
address_offset : 0x5018 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PWORD : Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 31 (32 bit)
access : read-write
Byte pin registers for all port GPIO pins
address_offset : 0x5B Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PBYTE : Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 0 (1 bit)
access : read-write
Byte pin registers for all port GPIO pins
address_offset : 0x6 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PBYTE : Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 0 (1 bit)
access : read-write
Direction registers for all port GPIO pins
address_offset : 0x6004 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DIRP : Selects pin direction for pin PIOm_n (bit 0 = PIOn_0, bit 1 = PIOn_1, etc.). Supported pins depends on the specific device and package. 0 = input. 1 = output.
bits : 0 - 31 (32 bit)
access : read-write
Word pin registers for all port GPIO pins
address_offset : 0x6028 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PWORD : Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 31 (32 bit)
access : read-write
Mask register for all port GPIO pins
address_offset : 0x6184 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MASKP : Controls which bits corresponding to PIOm_n are active in the MPORT register (bit 0 = PIOn_0, bit 1 = PIOn_1, etc.). Supported pins depends on the specific device and package.0 = Read MPORT: pin state; write MPORT: load output bit. 1 = Read MPORT: 0; write MPORT: output bit not affected.
bits : 0 - 31 (32 bit)
access : read-write
Port pin register for all port GPIO pins
address_offset : 0x6304 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PORT : Reads pin states or loads output bits (bit 0 = PIOn_0, bit 1 = PIOn_1, etc.). Supported pins depends on the specific device and package. 0 = Read: pin is low; write: clear output bit. 1 = Read: pin is high; write: set output bit.
bits : 0 - 31 (32 bit)
access : read-write
Masked port register for all port GPIO pins
address_offset : 0x6484 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MPORTP : Masked port register (bit 0 = PIOn_0, bit 1 = PIOn_1, etc.). Supported pins depends on the specific device and package. 0 = Read: pin is LOW and/or the corresponding bit in the MASK register is 1; write: clear output bit if the corresponding bit in the MASK register is 0. 1 = Read: pin is HIGH and the corresponding bit in the MASK register is 0; write: set output bit if the corresponding bit in the MASK register is 0.
bits : 0 - 31 (32 bit)
access : read-write
Write: Set register for port. Read: output bits for port
address_offset : 0x6604 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
SETP : Read or set output bits (bit 0 = PIOn_0, bit 1 = PIOn_1, etc.). Supported pins depends on the specific device and package. 0 = Read: output bit: write: no operation. 1 = Read: output bit; write: set output bit.
bits : 0 - 31 (32 bit)
access : read-write
Clear port for all port GPIO pins
address_offset : 0x6784 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
CLRP : Clear output bits (bit 0 = PIOn_0, bit 1 = PIOn_1, etc.). Supported pins depends on the specific device and package. 0 = No operation. 1 = Clear output bit.
bits : 0 - 31 (32 bit)
access : write-only
Byte pin registers for all port GPIO pins
address_offset : 0x69 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PBYTE : Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 0 (1 bit)
access : read-write
Toggle port for all port GPIO pins
address_offset : 0x6904 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
NOTP : Toggle output bits (bit 0 = PIOn_0, bit 1 = PIOn_1, etc.). Supported pins depends on the specific device and package. 0 = no operation. 1 = Toggle output bit.
bits : 0 - 31 (32 bit)
access : write-only
Set pin direction bits for port
address_offset : 0x6A84 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
DIRSETP : Set direction bits (bit 0 = PIOn_0, bit 1 = PIOn_1, etc.). Supported pins depends on the specific device and package. 0 = No operation. 1 = Set direction bit.
bits : 0 - 31 (32 bit)
access : write-only
Clear pin direction bits for port
address_offset : 0x6C04 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
DIRCLRP : Clear direction bits (bit 0 = PIOn_0, bit 1 = PIOn_1, etc.). Supported pins depends on the specific device and package. 0 = No operation. 1 = Clear direction bit.
bits : 0 - 31 (32 bit)
access : write-only
Toggle pin direction bits for port
address_offset : 0x6D84 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
DIRNOTP : Toggle direction bits (bit 0 = PIOn_0, bit 1 = PIOn_1, etc.). Supported pins depends on the specific device and package. 0 = no operation. 1 = Toggle direction bit.
bits : 0 - 31 (32 bit)
access : write-only
Word pin registers for all port GPIO pins
address_offset : 0x703C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PWORD : Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 31 (32 bit)
access : read-write
Byte pin registers for all port GPIO pins
address_offset : 0x78 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PBYTE : Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 0 (1 bit)
access : read-write
Word pin registers for all port GPIO pins
address_offset : 0x8054 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PWORD : Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 31 (32 bit)
access : read-write
Byte pin registers for all port GPIO pins
address_offset : 0x88 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PBYTE : Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 0 (1 bit)
access : read-write
Word pin registers for all port GPIO pins
address_offset : 0x9070 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PWORD : Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 31 (32 bit)
access : read-write
Byte pin registers for all port GPIO pins
address_offset : 0x99 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PBYTE : Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 0 (1 bit)
access : read-write
Byte pin registers for all port GPIO pins
address_offset : 0xA Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PBYTE : Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 0 (1 bit)
access : read-write
Word pin registers for all port GPIO pins
address_offset : 0xA090 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PWORD : Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 31 (32 bit)
access : read-write
Byte pin registers for all port GPIO pins
address_offset : 0xAB Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PBYTE : Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 0 (1 bit)
access : read-write
Word pin registers for all port GPIO pins
address_offset : 0xB0B4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PWORD : Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 31 (32 bit)
access : read-write
Byte pin registers for all port GPIO pins
address_offset : 0xBE Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PBYTE : Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 0 (1 bit)
access : read-write
Word pin registers for all port GPIO pins
address_offset : 0xC0DC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PWORD : Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 31 (32 bit)
access : read-write
Word pin registers for all port GPIO pins
address_offset : 0xD108 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PWORD : Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 31 (32 bit)
access : read-write
Byte pin registers for all port GPIO pins
address_offset : 0xD2 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PBYTE : Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 0 (1 bit)
access : read-write
Word pin registers for all port GPIO pins
address_offset : 0xE138 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PWORD : Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 31 (32 bit)
access : read-write
Byte pin registers for all port GPIO pins
address_offset : 0xE7 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PBYTE : Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 0 (1 bit)
access : read-write
Byte pin registers for all port GPIO pins
address_offset : 0xF Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PBYTE : Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 0 (1 bit)
access : read-write
Word pin registers for all port GPIO pins
address_offset : 0xF16C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PWORD : Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 31 (32 bit)
access : read-write
Byte pin registers for all port GPIO pins
address_offset : 0xFD Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PBYTE : Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 0 (1 bit)
access : read-write
Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !
This website is sponsored by Embeetle, an IDE designed from scratch for embedded software developers.