\n

IOCON

Peripheral Memory Blocks

address_offset : 0x0 Bytes (0x0)
size : 0x100 byte (0x0)
mem_usage : registers
protection : not protected

Registers

PIO0_0

PIO0_4

PIO0_5

PIO0_6

PIO0_7

PIO0_8

PIO0_9

PIO0_10

PIO0_11

PIO0_12

PIO0_13

PIO0_14

PIO0_15

PIO0_1

PIO0_16

PIO0_17

PIO0_18

PIO0_19

PIO0_20

PIO0_21

PIO0_22

PIO0_23

PIO0_24

PIO0_25

PIO0_26

PIO0_27

PIO0_28

PIO0_29

PIO0_30

PIO0_31

PIO0_2

PIO1_0

PIO1_1

PIO1_2

PIO1_3

PIO1_4

PIO1_5

PIO1_6

PIO1_7

PIO1_8

PIO1_9

PIO1_10

PIO1_11

PIO1_12

PIO1_13

PIO1_14

PIO1_15

PIO0_3

PIO1_16

PIO1_17

PIO1_18

PIO1_19

PIO1_20

PIO1_21

PIO1_22

PIO1_23

PIO1_24

PIO1_25

PIO1_26

PIO1_27

PIO1_28

PIO1_29

PIO1_30

PIO1_31


PIO0_0

Digital I/O control for port 0 pins PIO0_0
address_offset : 0x0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO0_0 PIO0_0 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE SLEW INVERT DIGIMODE OD ASW

FUNC : Selects pin function.
bits : 0 - 3 (4 bit)
access : read-write

Enumeration:

0 : ALT0

Alternative connection 0.

0x1 : ALT1

Alternative connection 1.

0x2 : ALT2

Alternative connection 2.

0x3 : ALT3

Alternative connection 3.

0x4 : ALT4

Alternative connection 4.

0x5 : ALT5

Alternative connection 5.

0x6 : ALT6

Alternative connection 6.

0x7 : ALT7

Alternative connection 7.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : INACTIVE

Inactive. Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN

Pull-down. Pull-down resistor enabled.

0x2 : PULL_UP

Pull-up. Pull-up resistor enabled.

0x3 : REPEATER

Repeater. Repeater mode.

End of enumeration elements list.

SLEW : Driver slew rate.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

0 : STANDARD

Standard-mode, output slew rate is slower. More outputs can be switched simultaneously.

0x1 : FAST

Fast-mode, output slew rate is faster. Refer to the appropriate specific device data sheet for details.

End of enumeration elements list.

INVERT : Input polarity.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

0 : DISABLED

Disabled. Input function is not inverted.

0x1 : ENABLED

Enabled. Input is function inverted.

End of enumeration elements list.

DIGIMODE : Select Digital mode.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

0 : ANALOG

Disable digital mode. Digital input set to 0.

0x1 : DIGITAL

Enable Digital mode. Digital input is enabled.

End of enumeration elements list.

OD : Controls open-drain mode.
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

0 : NORMAL

Normal. Normal push-pull output

0x1 : OPEN_DRAIN

Open-drain. Simulated open-drain output (high drive disabled).

End of enumeration elements list.

ASW : Analog switch input control.
bits : 10 - 10 (1 bit)
access : read-write

Enumeration:

0 : VALUE0

For pins PIO0_9, PIO0_11, PIO0_12, PIO0_15, PIO0_18, PIO0_31, PIO1_0 and PIO1_9, analog switch is closed (enabled). For the other pins, analog switch is open (disabled).

0x1 : VALUE1

For all pins except PIO0_9, PIO0_11, PIO0_12, PIO0_15, PIO0_18, PIO0_31, PIO1_0 and PIO1_9 analog switch is closed (enabled)

End of enumeration elements list.


PIO0_4

Digital I/O control for port 0 pins PIO0_4
address_offset : 0x10 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO0_4 PIO0_4 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE SLEW INVERT DIGIMODE OD

FUNC : Selects pin function.
bits : 0 - 3 (4 bit)
access : read-write

Enumeration:

0 : ALT0

Alternative connection 0.

0x1 : ALT1

Alternative connection 1.

0x2 : ALT2

Alternative connection 2.

0x3 : ALT3

Alternative connection 3.

0x4 : ALT4

Alternative connection 4.

0x5 : ALT5

Alternative connection 5.

0x6 : ALT6

Alternative connection 6.

0x7 : ALT7

Alternative connection 7.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : INACTIVE

Inactive. Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN

Pull-down. Pull-down resistor enabled.

0x2 : PULL_UP

Pull-up. Pull-up resistor enabled.

0x3 : REPEATER

Repeater. Repeater mode.

End of enumeration elements list.

SLEW : Driver slew rate.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

0 : STANDARD

Standard-mode, output slew rate is slower. More outputs can be switched simultaneously.

0x1 : FAST

Fast-mode, output slew rate is faster. Refer to the appropriate specific device data sheet for details.

End of enumeration elements list.

INVERT : Input polarity.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

0 : DISABLED

Disabled. Input function is not inverted.

0x1 : ENABLED

Enabled. Input is function inverted.

End of enumeration elements list.

DIGIMODE : Select Digital mode.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

0 : ANALOG

Disable digital mode. Digital input set to 0.

0x1 : DIGITAL

Enable Digital mode. Digital input is enabled.

End of enumeration elements list.

OD : Controls open-drain mode.
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

0 : NORMAL

Normal. Normal push-pull output

0x1 : OPEN_DRAIN

Open-drain. Simulated open-drain output (high drive disabled).

End of enumeration elements list.


PIO0_5

Digital I/O control for port 0 pins PIO0_5
address_offset : 0x14 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO0_5 PIO0_5 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE SLEW INVERT DIGIMODE OD

FUNC : Selects pin function.
bits : 0 - 3 (4 bit)
access : read-write

Enumeration:

0 : ALT0

Alternative connection 0.

0x1 : ALT1

Alternative connection 1.

0x2 : ALT2

Alternative connection 2.

0x3 : ALT3

Alternative connection 3.

0x4 : ALT4

Alternative connection 4.

0x5 : ALT5

Alternative connection 5.

0x6 : ALT6

Alternative connection 6.

0x7 : ALT7

Alternative connection 7.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : INACTIVE

Inactive. Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN

Pull-down. Pull-down resistor enabled.

0x2 : PULL_UP

Pull-up. Pull-up resistor enabled.

0x3 : REPEATER

Repeater. Repeater mode.

End of enumeration elements list.

SLEW : Driver slew rate.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

0 : STANDARD

Standard-mode, output slew rate is slower. More outputs can be switched simultaneously.

0x1 : FAST

Fast-mode, output slew rate is faster. Refer to the appropriate specific device data sheet for details.

End of enumeration elements list.

INVERT : Input polarity.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

0 : DISABLED

Disabled. Input function is not inverted.

0x1 : ENABLED

Enabled. Input is function inverted.

End of enumeration elements list.

DIGIMODE : Select Digital mode.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

0 : ANALOG

Disable digital mode. Digital input set to 0.

0x1 : DIGITAL

Enable Digital mode. Digital input is enabled.

End of enumeration elements list.

OD : Controls open-drain mode.
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

0 : NORMAL

Normal. Normal push-pull output

0x1 : OPEN_DRAIN

Open-drain. Simulated open-drain output (high drive disabled).

End of enumeration elements list.


PIO0_6

Digital I/O control for port 0 pins PIO0_6
address_offset : 0x18 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO0_6 PIO0_6 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE SLEW INVERT DIGIMODE OD

FUNC : Selects pin function.
bits : 0 - 3 (4 bit)
access : read-write

Enumeration:

0 : ALT0

Alternative connection 0.

0x1 : ALT1

Alternative connection 1.

0x2 : ALT2

Alternative connection 2.

0x3 : ALT3

Alternative connection 3.

0x4 : ALT4

Alternative connection 4.

0x5 : ALT5

Alternative connection 5.

0x6 : ALT6

Alternative connection 6.

0x7 : ALT7

Alternative connection 7.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : INACTIVE

Inactive. Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN

Pull-down. Pull-down resistor enabled.

0x2 : PULL_UP

Pull-up. Pull-up resistor enabled.

0x3 : REPEATER

Repeater. Repeater mode.

End of enumeration elements list.

SLEW : Driver slew rate.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

0 : STANDARD

Standard-mode, output slew rate is slower. More outputs can be switched simultaneously.

0x1 : FAST

Fast-mode, output slew rate is faster. Refer to the appropriate specific device data sheet for details.

End of enumeration elements list.

INVERT : Input polarity.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

0 : DISABLED

Disabled. Input function is not inverted.

0x1 : ENABLED

Enabled. Input is function inverted.

End of enumeration elements list.

DIGIMODE : Select Digital mode.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

0 : ANALOG

Disable digital mode. Digital input set to 0.

0x1 : DIGITAL

Enable Digital mode. Digital input is enabled.

End of enumeration elements list.

OD : Controls open-drain mode.
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

0 : NORMAL

Normal. Normal push-pull output

0x1 : OPEN_DRAIN

Open-drain. Simulated open-drain output (high drive disabled).

End of enumeration elements list.


PIO0_7

Digital I/O control for port 0 pins PIO0_7
address_offset : 0x1C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO0_7 PIO0_7 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE SLEW INVERT DIGIMODE OD

FUNC : Selects pin function.
bits : 0 - 3 (4 bit)
access : read-write

Enumeration:

0 : ALT0

Alternative connection 0.

0x1 : ALT1

Alternative connection 1.

0x2 : ALT2

Alternative connection 2.

0x3 : ALT3

Alternative connection 3.

0x4 : ALT4

Alternative connection 4.

0x5 : ALT5

Alternative connection 5.

0x6 : ALT6

Alternative connection 6.

0x7 : ALT7

Alternative connection 7.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : INACTIVE

Inactive. Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN

Pull-down. Pull-down resistor enabled.

0x2 : PULL_UP

Pull-up. Pull-up resistor enabled.

0x3 : REPEATER

Repeater. Repeater mode.

End of enumeration elements list.

SLEW : Driver slew rate.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

0 : STANDARD

Standard-mode, output slew rate is slower. More outputs can be switched simultaneously.

0x1 : FAST

Fast-mode, output slew rate is faster. Refer to the appropriate specific device data sheet for details.

End of enumeration elements list.

INVERT : Input polarity.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

0 : DISABLED

Disabled. Input function is not inverted.

0x1 : ENABLED

Enabled. Input is function inverted.

End of enumeration elements list.

DIGIMODE : Select Digital mode.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

0 : ANALOG

Disable digital mode. Digital input set to 0.

0x1 : DIGITAL

Enable Digital mode. Digital input is enabled.

End of enumeration elements list.

OD : Controls open-drain mode.
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

0 : NORMAL

Normal. Normal push-pull output

0x1 : OPEN_DRAIN

Open-drain. Simulated open-drain output (high drive disabled).

End of enumeration elements list.


PIO0_8

Digital I/O control for port 0 pins PIO0_8
address_offset : 0x20 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO0_8 PIO0_8 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE SLEW INVERT DIGIMODE OD

FUNC : Selects pin function.
bits : 0 - 3 (4 bit)
access : read-write

Enumeration:

0 : ALT0

Alternative connection 0.

0x1 : ALT1

Alternative connection 1.

0x2 : ALT2

Alternative connection 2.

0x3 : ALT3

Alternative connection 3.

0x4 : ALT4

Alternative connection 4.

0x5 : ALT5

Alternative connection 5.

0x6 : ALT6

Alternative connection 6.

0x7 : ALT7

Alternative connection 7.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : INACTIVE

Inactive. Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN

Pull-down. Pull-down resistor enabled.

0x2 : PULL_UP

Pull-up. Pull-up resistor enabled.

0x3 : REPEATER

Repeater. Repeater mode.

End of enumeration elements list.

SLEW : Driver slew rate.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

0 : STANDARD

Standard-mode, output slew rate is slower. More outputs can be switched simultaneously.

0x1 : FAST

Fast-mode, output slew rate is faster. Refer to the appropriate specific device data sheet for details.

End of enumeration elements list.

INVERT : Input polarity.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

0 : DISABLED

Disabled. Input function is not inverted.

0x1 : ENABLED

Enabled. Input is function inverted.

End of enumeration elements list.

DIGIMODE : Select Digital mode.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

0 : ANALOG

Disable digital mode. Digital input set to 0.

0x1 : DIGITAL

Enable Digital mode. Digital input is enabled.

End of enumeration elements list.

OD : Controls open-drain mode.
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

0 : NORMAL

Normal. Normal push-pull output

0x1 : OPEN_DRAIN

Open-drain. Simulated open-drain output (high drive disabled).

End of enumeration elements list.


PIO0_9

Digital I/O control for port 0 pins PIO0_9
address_offset : 0x24 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO0_9 PIO0_9 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE SLEW INVERT DIGIMODE OD ASW

FUNC : Selects pin function.
bits : 0 - 3 (4 bit)
access : read-write

Enumeration:

0 : ALT0

Alternative connection 0.

0x1 : ALT1

Alternative connection 1.

0x2 : ALT2

Alternative connection 2.

0x3 : ALT3

Alternative connection 3.

0x4 : ALT4

Alternative connection 4.

0x5 : ALT5

Alternative connection 5.

0x6 : ALT6

Alternative connection 6.

0x7 : ALT7

Alternative connection 7.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : INACTIVE

Inactive. Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN

Pull-down. Pull-down resistor enabled.

0x2 : PULL_UP

Pull-up. Pull-up resistor enabled.

0x3 : REPEATER

Repeater. Repeater mode.

End of enumeration elements list.

SLEW : Driver slew rate.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

0 : STANDARD

Standard-mode, output slew rate is slower. More outputs can be switched simultaneously.

0x1 : FAST

Fast-mode, output slew rate is faster. Refer to the appropriate specific device data sheet for details.

End of enumeration elements list.

INVERT : Input polarity.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

0 : DISABLED

Disabled. Input function is not inverted.

0x1 : ENABLED

Enabled. Input is function inverted.

End of enumeration elements list.

DIGIMODE : Select Digital mode.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

0 : ANALOG

Disable digital mode. Digital input set to 0.

0x1 : DIGITAL

Enable Digital mode. Digital input is enabled.

End of enumeration elements list.

OD : Controls open-drain mode.
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

0 : NORMAL

Normal. Normal push-pull output

0x1 : OPEN_DRAIN

Open-drain. Simulated open-drain output (high drive disabled).

End of enumeration elements list.

ASW : Analog switch input control.
bits : 10 - 10 (1 bit)
access : read-write

Enumeration:

0 : VALUE0

For pins PIO0_9, PIO0_11, PIO0_12, PIO0_15, PIO0_18, PIO0_31, PIO1_0 and PIO1_9, analog switch is closed (enabled). For the other pins, analog switch is open (disabled).

0x1 : VALUE1

For all pins except PIO0_9, PIO0_11, PIO0_12, PIO0_15, PIO0_18, PIO0_31, PIO1_0 and PIO1_9 analog switch is closed (enabled)

End of enumeration elements list.


PIO0_10

Digital I/O control for port 0 pins PIO0_10
address_offset : 0x28 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO0_10 PIO0_10 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE SLEW INVERT DIGIMODE OD ASW

FUNC : Selects pin function.
bits : 0 - 3 (4 bit)
access : read-write

Enumeration:

0 : ALT0

Alternative connection 0.

0x1 : ALT1

Alternative connection 1.

0x2 : ALT2

Alternative connection 2.

0x3 : ALT3

Alternative connection 3.

0x4 : ALT4

Alternative connection 4.

0x5 : ALT5

Alternative connection 5.

0x6 : ALT6

Alternative connection 6.

0x7 : ALT7

Alternative connection 7.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : INACTIVE

Inactive. Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN

Pull-down. Pull-down resistor enabled.

0x2 : PULL_UP

Pull-up. Pull-up resistor enabled.

0x3 : REPEATER

Repeater. Repeater mode.

End of enumeration elements list.

SLEW : Driver slew rate.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

0 : STANDARD

Standard-mode, output slew rate is slower. More outputs can be switched simultaneously.

0x1 : FAST

Fast-mode, output slew rate is faster. Refer to the appropriate specific device data sheet for details.

End of enumeration elements list.

INVERT : Input polarity.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

0 : DISABLED

Disabled. Input function is not inverted.

0x1 : ENABLED

Enabled. Input is function inverted.

End of enumeration elements list.

DIGIMODE : Select Digital mode.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

0 : ANALOG

Disable digital mode. Digital input set to 0.

0x1 : DIGITAL

Enable Digital mode. Digital input is enabled.

End of enumeration elements list.

OD : Controls open-drain mode.
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

0 : NORMAL

Normal. Normal push-pull output

0x1 : OPEN_DRAIN

Open-drain. Simulated open-drain output (high drive disabled).

End of enumeration elements list.

ASW : Analog switch input control.
bits : 10 - 10 (1 bit)
access : read-write

Enumeration:

0 : VALUE0

For pins PIO0_9, PIO0_11, PIO0_12, PIO0_15, PIO0_18, PIO0_31, PIO1_0 and PIO1_9, analog switch is closed (enabled). For the other pins, analog switch is open (disabled).

0x1 : VALUE1

For all pins except PIO0_9, PIO0_11, PIO0_12, PIO0_15, PIO0_18, PIO0_31, PIO1_0 and PIO1_9 analog switch is closed (enabled)

End of enumeration elements list.


PIO0_11

Digital I/O control for port 0 pins PIO0_11
address_offset : 0x2C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO0_11 PIO0_11 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE SLEW INVERT DIGIMODE OD ASW

FUNC : Selects pin function.
bits : 0 - 3 (4 bit)
access : read-write

Enumeration:

0 : ALT0

Alternative connection 0.

0x1 : ALT1

Alternative connection 1.

0x2 : ALT2

Alternative connection 2.

0x3 : ALT3

Alternative connection 3.

0x4 : ALT4

Alternative connection 4.

0x5 : ALT5

Alternative connection 5.

0x6 : ALT6

Alternative connection 6.

0x7 : ALT7

Alternative connection 7.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : INACTIVE

Inactive. Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN

Pull-down. Pull-down resistor enabled.

0x2 : PULL_UP

Pull-up. Pull-up resistor enabled.

0x3 : REPEATER

Repeater. Repeater mode.

End of enumeration elements list.

SLEW : Driver slew rate.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

0 : STANDARD

Standard-mode, output slew rate is slower. More outputs can be switched simultaneously.

0x1 : FAST

Fast-mode, output slew rate is faster. Refer to the appropriate specific device data sheet for details.

End of enumeration elements list.

INVERT : Input polarity.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

0 : DISABLED

Disabled. Input function is not inverted.

0x1 : ENABLED

Enabled. Input is function inverted.

End of enumeration elements list.

DIGIMODE : Select Digital mode.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

0 : ANALOG

Disable digital mode. Digital input set to 0.

0x1 : DIGITAL

Enable Digital mode. Digital input is enabled.

End of enumeration elements list.

OD : Controls open-drain mode.
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

0 : NORMAL

Normal. Normal push-pull output

0x1 : OPEN_DRAIN

Open-drain. Simulated open-drain output (high drive disabled).

End of enumeration elements list.

ASW : Analog switch input control.
bits : 10 - 10 (1 bit)
access : read-write

Enumeration:

0 : VALUE0

For pins PIO0_9, PIO0_11, PIO0_12, PIO0_15, PIO0_18, PIO0_31, PIO1_0 and PIO1_9, analog switch is closed (enabled). For the other pins, analog switch is open (disabled).

0x1 : VALUE1

For all pins except PIO0_9, PIO0_11, PIO0_12, PIO0_15, PIO0_18, PIO0_31, PIO1_0 and PIO1_9 analog switch is closed (enabled)

End of enumeration elements list.


PIO0_12

Digital I/O control for port 0 pins PIO0_12
address_offset : 0x30 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO0_12 PIO0_12 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE SLEW INVERT DIGIMODE OD ASW

FUNC : Selects pin function.
bits : 0 - 3 (4 bit)
access : read-write

Enumeration:

0 : ALT0

Alternative connection 0.

0x1 : ALT1

Alternative connection 1.

0x2 : ALT2

Alternative connection 2.

0x3 : ALT3

Alternative connection 3.

0x4 : ALT4

Alternative connection 4.

0x5 : ALT5

Alternative connection 5.

0x6 : ALT6

Alternative connection 6.

0x7 : ALT7

Alternative connection 7.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : INACTIVE

Inactive. Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN

Pull-down. Pull-down resistor enabled.

0x2 : PULL_UP

Pull-up. Pull-up resistor enabled.

0x3 : REPEATER

Repeater. Repeater mode.

End of enumeration elements list.

SLEW : Driver slew rate.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

0 : STANDARD

Standard-mode, output slew rate is slower. More outputs can be switched simultaneously.

0x1 : FAST

Fast-mode, output slew rate is faster. Refer to the appropriate specific device data sheet for details.

End of enumeration elements list.

INVERT : Input polarity.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

0 : DISABLED

Disabled. Input function is not inverted.

0x1 : ENABLED

Enabled. Input is function inverted.

End of enumeration elements list.

DIGIMODE : Select Digital mode.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

0 : ANALOG

Disable digital mode. Digital input set to 0.

0x1 : DIGITAL

Enable Digital mode. Digital input is enabled.

End of enumeration elements list.

OD : Controls open-drain mode.
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

0 : NORMAL

Normal. Normal push-pull output

0x1 : OPEN_DRAIN

Open-drain. Simulated open-drain output (high drive disabled).

End of enumeration elements list.

ASW : Analog switch input control.
bits : 10 - 10 (1 bit)
access : read-write

Enumeration:

0 : VALUE0

For pins PIO0_9, PIO0_11, PIO0_12, PIO0_15, PIO0_18, PIO0_31, PIO1_0 and PIO1_9, analog switch is closed (enabled). For the other pins, analog switch is open (disabled).

0x1 : VALUE1

For all pins except PIO0_9, PIO0_11, PIO0_12, PIO0_15, PIO0_18, PIO0_31, PIO1_0 and PIO1_9 analog switch is closed (enabled)

End of enumeration elements list.


PIO0_13

Digital I/O control for port 0 pins PIO0_13
address_offset : 0x34 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO0_13 PIO0_13 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE SLEW INVERT DIGIMODE OD SSEL FILTEROFF ECS EGP I2CFILTER

FUNC : Selects pin function.
bits : 0 - 3 (4 bit)
access : read-write

Enumeration:

0 : ALT0

Alternative connection 0.

0x1 : ALT1

Alternative connection 1.

0x2 : ALT2

Alternative connection 2.

0x3 : ALT3

Alternative connection 3.

0x4 : ALT4

Alternative connection 4.

0x5 : ALT5

Alternative connection 5.

0x6 : ALT6

Alternative connection 6.

0x7 : ALT7

Alternative connection 7.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : INACTIVE

Inactive. Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN

Pull-down. Pull-down resistor enabled.

0x2 : PULL_UP

Pull-up. Pull-up resistor enabled.

0x3 : REPEATER

Repeater. Repeater mode.

End of enumeration elements list.

SLEW : Driver slew rate.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

0 : STANDARD

Standard-mode, output slew rate is slower. More outputs can be switched simultaneously.

0x1 : FAST

Fast-mode, output slew rate is faster. Refer to the appropriate specific device data sheet for details.

End of enumeration elements list.

INVERT : Input polarity.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

0 : DISABLED

Disabled. Input function is not inverted.

0x1 : ENABLED

Enabled. Input is function inverted.

End of enumeration elements list.

DIGIMODE : Select Digital mode.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

0 : ANALOG

Disable digital mode. Digital input set to 0.

0x1 : DIGITAL

Enable Digital mode. Digital input is enabled.

End of enumeration elements list.

OD : Controls open-drain mode in standard GPIO mode (EGP = 1). This bit has no effect in I2C mode (EGP=0).
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

0 : NORMAL

Normal. Normal push-pull output

0x1 : OPEN_DRAIN

Open-drain. Simulated open-drain output (high drive disabled).

End of enumeration elements list.

SSEL : Supply Selection bit.
bits : 11 - 11 (1 bit)
access : read-write

Enumeration:

0 : SEL3V3

3V3 Signaling in I2C Mode.

0x1 : SEL1V8

1V8 Signaling in I2C Mode.

End of enumeration elements list.

FILTEROFF : Controls input glitch filter.
bits : 12 - 12 (1 bit)
access : read-write

Enumeration:

0 : ENABLED

Filter enabled.

0x1 : DISABLED

Filter disabled.

End of enumeration elements list.

ECS : Pull-up current source enable in I2C mode.
bits : 13 - 13 (1 bit)
access : read-write

Enumeration:

0 : DISABLED

Disabled. IO is in open drain cell.

0x1 : ENABLED

Enabled. Pull resistor is conencted.

End of enumeration elements list.

EGP : Switch between GPIO mode and I2C mode.
bits : 14 - 14 (1 bit)
access : read-write

Enumeration:

0 : I2C_MODE

I2C mode.

0x1 : GPIO_MODE

GPIO mode.

End of enumeration elements list.

I2CFILTER : Configures I2C features for standard mode, fast mode, and Fast Mode Plus operation and High-Speed mode operation.
bits : 15 - 15 (1 bit)
access : read-write

Enumeration:

0 : FAST_MODE

I2C 50 ns glitch filter enabled. Typically used for Standard-mode, Fast-mode and Fast-mode Plus I2C.

0x1 : STANDARD_MODE

I2C 10 ns glitch filter enabled. Typically used for High-speed mode I2C.

End of enumeration elements list.


PIO0_14

Digital I/O control for port 0 pins PIO0_14
address_offset : 0x38 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO0_14 PIO0_14 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE SLEW INVERT DIGIMODE OD SSEL FILTEROFF ECS EGP I2CFILTER

FUNC : Selects pin function.
bits : 0 - 3 (4 bit)
access : read-write

Enumeration:

0 : ALT0

Alternative connection 0.

0x1 : ALT1

Alternative connection 1.

0x2 : ALT2

Alternative connection 2.

0x3 : ALT3

Alternative connection 3.

0x4 : ALT4

Alternative connection 4.

0x5 : ALT5

Alternative connection 5.

0x6 : ALT6

Alternative connection 6.

0x7 : ALT7

Alternative connection 7.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : INACTIVE

Inactive. Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN

Pull-down. Pull-down resistor enabled.

0x2 : PULL_UP

Pull-up. Pull-up resistor enabled.

0x3 : REPEATER

Repeater. Repeater mode.

End of enumeration elements list.

SLEW : Driver slew rate.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

0 : STANDARD

Standard-mode, output slew rate is slower. More outputs can be switched simultaneously.

0x1 : FAST

Fast-mode, output slew rate is faster. Refer to the appropriate specific device data sheet for details.

End of enumeration elements list.

INVERT : Input polarity.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

0 : DISABLED

Disabled. Input function is not inverted.

0x1 : ENABLED

Enabled. Input is function inverted.

End of enumeration elements list.

DIGIMODE : Select Digital mode.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

0 : ANALOG

Disable digital mode. Digital input set to 0.

0x1 : DIGITAL

Enable Digital mode. Digital input is enabled.

End of enumeration elements list.

OD : Controls open-drain mode in standard GPIO mode (EGP = 1). This bit has no effect in I2C mode (EGP=0).
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

0 : NORMAL

Normal. Normal push-pull output

0x1 : OPEN_DRAIN

Open-drain. Simulated open-drain output (high drive disabled).

End of enumeration elements list.

SSEL : Supply Selection bit.
bits : 11 - 11 (1 bit)
access : read-write

Enumeration:

0 : SEL3V3

3V3 Signaling in I2C Mode.

0x1 : SEL1V8

1V8 Signaling in I2C Mode.

End of enumeration elements list.

FILTEROFF : Controls input glitch filter.
bits : 12 - 12 (1 bit)
access : read-write

Enumeration:

0 : ENABLED

Filter enabled.

0x1 : DISABLED

Filter disabled.

End of enumeration elements list.

ECS : Pull-up current source enable in I2C mode.
bits : 13 - 13 (1 bit)
access : read-write

Enumeration:

0 : DISABLED

Disabled. IO is in open drain cell.

0x1 : ENABLED

Enabled. Pull resistor is conencted.

End of enumeration elements list.

EGP : Switch between GPIO mode and I2C mode.
bits : 14 - 14 (1 bit)
access : read-write

Enumeration:

0 : I2C_MODE

I2C mode.

0x1 : GPIO_MODE

GPIO mode.

End of enumeration elements list.

I2CFILTER : Configures I2C features for standard mode, fast mode, and Fast Mode Plus operation and High-Speed mode operation.
bits : 15 - 15 (1 bit)
access : read-write

Enumeration:

0 : FAST_MODE

I2C 50 ns glitch filter enabled. Typically used for Standard-mode, Fast-mode and Fast-mode Plus I2C.

0x1 : STANDARD_MODE

I2C 10 ns glitch filter enabled. Typically used for High-speed mode I2C.

End of enumeration elements list.


PIO0_15

Digital I/O control for port 0 pins PIO0_15
address_offset : 0x3C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO0_15 PIO0_15 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE SLEW INVERT DIGIMODE OD ASW

FUNC : Selects pin function.
bits : 0 - 3 (4 bit)
access : read-write

Enumeration:

0 : ALT0

Alternative connection 0.

0x1 : ALT1

Alternative connection 1.

0x2 : ALT2

Alternative connection 2.

0x3 : ALT3

Alternative connection 3.

0x4 : ALT4

Alternative connection 4.

0x5 : ALT5

Alternative connection 5.

0x6 : ALT6

Alternative connection 6.

0x7 : ALT7

Alternative connection 7.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : INACTIVE

Inactive. Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN

Pull-down. Pull-down resistor enabled.

0x2 : PULL_UP

Pull-up. Pull-up resistor enabled.

0x3 : REPEATER

Repeater. Repeater mode.

End of enumeration elements list.

SLEW : Driver slew rate.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

0 : STANDARD

Standard-mode, output slew rate is slower. More outputs can be switched simultaneously.

0x1 : FAST

Fast-mode, output slew rate is faster. Refer to the appropriate specific device data sheet for details.

End of enumeration elements list.

INVERT : Input polarity.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

0 : DISABLED

Disabled. Input function is not inverted.

0x1 : ENABLED

Enabled. Input is function inverted.

End of enumeration elements list.

DIGIMODE : Select Digital mode.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

0 : ANALOG

Disable digital mode. Digital input set to 0.

0x1 : DIGITAL

Enable Digital mode. Digital input is enabled.

End of enumeration elements list.

OD : Controls open-drain mode.
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

0 : NORMAL

Normal. Normal push-pull output

0x1 : OPEN_DRAIN

Open-drain. Simulated open-drain output (high drive disabled).

End of enumeration elements list.

ASW : Analog switch input control.
bits : 10 - 10 (1 bit)
access : read-write

Enumeration:

0 : VALUE0

For pins PIO0_9, PIO0_11, PIO0_12, PIO0_15, PIO0_18, PIO0_31, PIO1_0 and PIO1_9, analog switch is closed (enabled). For the other pins, analog switch is open (disabled).

0x1 : VALUE1

For all pins except PIO0_9, PIO0_11, PIO0_12, PIO0_15, PIO0_18, PIO0_31, PIO1_0 and PIO1_9 analog switch is closed (enabled)

End of enumeration elements list.


PIO0_1

Digital I/O control for port 0 pins PIO0_1
address_offset : 0x4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO0_1 PIO0_1 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE SLEW INVERT DIGIMODE OD

FUNC : Selects pin function.
bits : 0 - 3 (4 bit)
access : read-write

Enumeration:

0 : ALT0

Alternative connection 0.

0x1 : ALT1

Alternative connection 1.

0x2 : ALT2

Alternative connection 2.

0x3 : ALT3

Alternative connection 3.

0x4 : ALT4

Alternative connection 4.

0x5 : ALT5

Alternative connection 5.

0x6 : ALT6

Alternative connection 6.

0x7 : ALT7

Alternative connection 7.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : INACTIVE

Inactive. Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN

Pull-down. Pull-down resistor enabled.

0x2 : PULL_UP

Pull-up. Pull-up resistor enabled.

0x3 : REPEATER

Repeater. Repeater mode.

End of enumeration elements list.

SLEW : Driver slew rate.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

0 : STANDARD

Standard-mode, output slew rate is slower. More outputs can be switched simultaneously.

0x1 : FAST

Fast-mode, output slew rate is faster. Refer to the appropriate specific device data sheet for details.

End of enumeration elements list.

INVERT : Input polarity.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

0 : DISABLED

Disabled. Input function is not inverted.

0x1 : ENABLED

Enabled. Input is function inverted.

End of enumeration elements list.

DIGIMODE : Select Digital mode.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

0 : ANALOG

Disable digital mode. Digital input set to 0.

0x1 : DIGITAL

Enable Digital mode. Digital input is enabled.

End of enumeration elements list.

OD : Controls open-drain mode.
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

0 : NORMAL

Normal. Normal push-pull output

0x1 : OPEN_DRAIN

Open-drain. Simulated open-drain output (high drive disabled).

End of enumeration elements list.


PIO0_16

Digital I/O control for port 0 pins PIO0_16
address_offset : 0x40 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO0_16 PIO0_16 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE SLEW INVERT DIGIMODE OD ASW

FUNC : Selects pin function.
bits : 0 - 3 (4 bit)
access : read-write

Enumeration:

0 : ALT0

Alternative connection 0.

0x1 : ALT1

Alternative connection 1.

0x2 : ALT2

Alternative connection 2.

0x3 : ALT3

Alternative connection 3.

0x4 : ALT4

Alternative connection 4.

0x5 : ALT5

Alternative connection 5.

0x6 : ALT6

Alternative connection 6.

0x7 : ALT7

Alternative connection 7.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : INACTIVE

Inactive. Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN

Pull-down. Pull-down resistor enabled.

0x2 : PULL_UP

Pull-up. Pull-up resistor enabled.

0x3 : REPEATER

Repeater. Repeater mode.

End of enumeration elements list.

SLEW : Driver slew rate.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

0 : STANDARD

Standard-mode, output slew rate is slower. More outputs can be switched simultaneously.

0x1 : FAST

Fast-mode, output slew rate is faster. Refer to the appropriate specific device data sheet for details.

End of enumeration elements list.

INVERT : Input polarity.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

0 : DISABLED

Disabled. Input function is not inverted.

0x1 : ENABLED

Enabled. Input is function inverted.

End of enumeration elements list.

DIGIMODE : Select Digital mode.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

0 : ANALOG

Disable digital mode. Digital input set to 0.

0x1 : DIGITAL

Enable Digital mode. Digital input is enabled.

End of enumeration elements list.

OD : Controls open-drain mode.
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

0 : NORMAL

Normal. Normal push-pull output

0x1 : OPEN_DRAIN

Open-drain. Simulated open-drain output (high drive disabled).

End of enumeration elements list.

ASW : Analog switch input control.
bits : 10 - 10 (1 bit)
access : read-write

Enumeration:

0 : VALUE0

For pins PIO0_9, PIO0_11, PIO0_12, PIO0_15, PIO0_18, PIO0_31, PIO1_0 and PIO1_9, analog switch is closed (enabled). For the other pins, analog switch is open (disabled).

0x1 : VALUE1

For all pins except PIO0_9, PIO0_11, PIO0_12, PIO0_15, PIO0_18, PIO0_31, PIO1_0 and PIO1_9 analog switch is closed (enabled)

End of enumeration elements list.


PIO0_17

Digital I/O control for port 0 pins PIO0_17
address_offset : 0x44 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO0_17 PIO0_17 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE SLEW INVERT DIGIMODE OD

FUNC : Selects pin function.
bits : 0 - 3 (4 bit)
access : read-write

Enumeration:

0 : ALT0

Alternative connection 0.

0x1 : ALT1

Alternative connection 1.

0x2 : ALT2

Alternative connection 2.

0x3 : ALT3

Alternative connection 3.

0x4 : ALT4

Alternative connection 4.

0x5 : ALT5

Alternative connection 5.

0x6 : ALT6

Alternative connection 6.

0x7 : ALT7

Alternative connection 7.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : INACTIVE

Inactive. Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN

Pull-down. Pull-down resistor enabled.

0x2 : PULL_UP

Pull-up. Pull-up resistor enabled.

0x3 : REPEATER

Repeater. Repeater mode.

End of enumeration elements list.

SLEW : Driver slew rate.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

0 : STANDARD

Standard-mode, output slew rate is slower. More outputs can be switched simultaneously.

0x1 : FAST

Fast-mode, output slew rate is faster. Refer to the appropriate specific device data sheet for details.

End of enumeration elements list.

INVERT : Input polarity.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

0 : DISABLED

Disabled. Input function is not inverted.

0x1 : ENABLED

Enabled. Input is function inverted.

End of enumeration elements list.

DIGIMODE : Select Digital mode.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

0 : ANALOG

Disable digital mode. Digital input set to 0.

0x1 : DIGITAL

Enable Digital mode. Digital input is enabled.

End of enumeration elements list.

OD : Controls open-drain mode.
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

0 : NORMAL

Normal. Normal push-pull output

0x1 : OPEN_DRAIN

Open-drain. Simulated open-drain output (high drive disabled).

End of enumeration elements list.


PIO0_18

Digital I/O control for port 0 pins PIO0_18
address_offset : 0x48 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO0_18 PIO0_18 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE SLEW INVERT DIGIMODE OD ASW

FUNC : Selects pin function.
bits : 0 - 3 (4 bit)
access : read-write

Enumeration:

0 : ALT0

Alternative connection 0.

0x1 : ALT1

Alternative connection 1.

0x2 : ALT2

Alternative connection 2.

0x3 : ALT3

Alternative connection 3.

0x4 : ALT4

Alternative connection 4.

0x5 : ALT5

Alternative connection 5.

0x6 : ALT6

Alternative connection 6.

0x7 : ALT7

Alternative connection 7.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : INACTIVE

Inactive. Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN

Pull-down. Pull-down resistor enabled.

0x2 : PULL_UP

Pull-up. Pull-up resistor enabled.

0x3 : REPEATER

Repeater. Repeater mode.

End of enumeration elements list.

SLEW : Driver slew rate.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

0 : STANDARD

Standard-mode, output slew rate is slower. More outputs can be switched simultaneously.

0x1 : FAST

Fast-mode, output slew rate is faster. Refer to the appropriate specific device data sheet for details.

End of enumeration elements list.

INVERT : Input polarity.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

0 : DISABLED

Disabled. Input function is not inverted.

0x1 : ENABLED

Enabled. Input is function inverted.

End of enumeration elements list.

DIGIMODE : Select Digital mode.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

0 : ANALOG

Disable digital mode. Digital input set to 0.

0x1 : DIGITAL

Enable Digital mode. Digital input is enabled.

End of enumeration elements list.

OD : Controls open-drain mode.
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

0 : NORMAL

Normal. Normal push-pull output

0x1 : OPEN_DRAIN

Open-drain. Simulated open-drain output (high drive disabled).

End of enumeration elements list.

ASW : Analog switch input control.
bits : 10 - 10 (1 bit)
access : read-write

Enumeration:

0 : VALUE0

For pins PIO0_9, PIO0_11, PIO0_12, PIO0_15, PIO0_18, PIO0_31, PIO1_0 and PIO1_9, analog switch is closed (enabled). For the other pins, analog switch is open (disabled).

0x1 : VALUE1

For all pins except PIO0_9, PIO0_11, PIO0_12, PIO0_15, PIO0_18, PIO0_31, PIO1_0 and PIO1_9 analog switch is closed (enabled)

End of enumeration elements list.


PIO0_19

Digital I/O control for port 0 pins PIO0_19
address_offset : 0x4C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO0_19 PIO0_19 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE SLEW INVERT DIGIMODE OD

FUNC : Selects pin function.
bits : 0 - 3 (4 bit)
access : read-write

Enumeration:

0 : ALT0

Alternative connection 0.

0x1 : ALT1

Alternative connection 1.

0x2 : ALT2

Alternative connection 2.

0x3 : ALT3

Alternative connection 3.

0x4 : ALT4

Alternative connection 4.

0x5 : ALT5

Alternative connection 5.

0x6 : ALT6

Alternative connection 6.

0x7 : ALT7

Alternative connection 7.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : INACTIVE

Inactive. Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN

Pull-down. Pull-down resistor enabled.

0x2 : PULL_UP

Pull-up. Pull-up resistor enabled.

0x3 : REPEATER

Repeater. Repeater mode.

End of enumeration elements list.

SLEW : Driver slew rate.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

0 : STANDARD

Standard-mode, output slew rate is slower. More outputs can be switched simultaneously.

0x1 : FAST

Fast-mode, output slew rate is faster. Refer to the appropriate specific device data sheet for details.

End of enumeration elements list.

INVERT : Input polarity.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

0 : DISABLED

Disabled. Input function is not inverted.

0x1 : ENABLED

Enabled. Input is function inverted.

End of enumeration elements list.

DIGIMODE : Select Digital mode.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

0 : ANALOG

Disable digital mode. Digital input set to 0.

0x1 : DIGITAL

Enable Digital mode. Digital input is enabled.

End of enumeration elements list.

OD : Controls open-drain mode.
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

0 : NORMAL

Normal. Normal push-pull output

0x1 : OPEN_DRAIN

Open-drain. Simulated open-drain output (high drive disabled).

End of enumeration elements list.


PIO0_20

Digital I/O control for port 0 pins PIO0_20
address_offset : 0x50 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO0_20 PIO0_20 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE SLEW INVERT DIGIMODE OD

FUNC : Selects pin function.
bits : 0 - 3 (4 bit)
access : read-write

Enumeration:

0 : ALT0

Alternative connection 0.

0x1 : ALT1

Alternative connection 1.

0x2 : ALT2

Alternative connection 2.

0x3 : ALT3

Alternative connection 3.

0x4 : ALT4

Alternative connection 4.

0x5 : ALT5

Alternative connection 5.

0x6 : ALT6

Alternative connection 6.

0x7 : ALT7

Alternative connection 7.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : INACTIVE

Inactive. Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN

Pull-down. Pull-down resistor enabled.

0x2 : PULL_UP

Pull-up. Pull-up resistor enabled.

0x3 : REPEATER

Repeater. Repeater mode.

End of enumeration elements list.

SLEW : Driver slew rate.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

0 : STANDARD

Standard-mode, output slew rate is slower. More outputs can be switched simultaneously.

0x1 : FAST

Fast-mode, output slew rate is faster. Refer to the appropriate specific device data sheet for details.

End of enumeration elements list.

INVERT : Input polarity.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

0 : DISABLED

Disabled. Input function is not inverted.

0x1 : ENABLED

Enabled. Input is function inverted.

End of enumeration elements list.

DIGIMODE : Select Digital mode.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

0 : ANALOG

Disable digital mode. Digital input set to 0.

0x1 : DIGITAL

Enable Digital mode. Digital input is enabled.

End of enumeration elements list.

OD : Controls open-drain mode.
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

0 : NORMAL

Normal. Normal push-pull output

0x1 : OPEN_DRAIN

Open-drain. Simulated open-drain output (high drive disabled).

End of enumeration elements list.


PIO0_21

Digital I/O control for port 0 pins PIO0_21
address_offset : 0x54 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO0_21 PIO0_21 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE SLEW INVERT DIGIMODE OD

FUNC : Selects pin function.
bits : 0 - 3 (4 bit)
access : read-write

Enumeration:

0 : ALT0

Alternative connection 0.

0x1 : ALT1

Alternative connection 1.

0x2 : ALT2

Alternative connection 2.

0x3 : ALT3

Alternative connection 3.

0x4 : ALT4

Alternative connection 4.

0x5 : ALT5

Alternative connection 5.

0x6 : ALT6

Alternative connection 6.

0x7 : ALT7

Alternative connection 7.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : INACTIVE

Inactive. Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN

Pull-down. Pull-down resistor enabled.

0x2 : PULL_UP

Pull-up. Pull-up resistor enabled.

0x3 : REPEATER

Repeater. Repeater mode.

End of enumeration elements list.

SLEW : Driver slew rate.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

0 : STANDARD

Standard-mode, output slew rate is slower. More outputs can be switched simultaneously.

0x1 : FAST

Fast-mode, output slew rate is faster. Refer to the appropriate specific device data sheet for details.

End of enumeration elements list.

INVERT : Input polarity.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

0 : DISABLED

Disabled. Input function is not inverted.

0x1 : ENABLED

Enabled. Input is function inverted.

End of enumeration elements list.

DIGIMODE : Select Digital mode.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

0 : ANALOG

Disable digital mode. Digital input set to 0.

0x1 : DIGITAL

Enable Digital mode. Digital input is enabled.

End of enumeration elements list.

OD : Controls open-drain mode.
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

0 : NORMAL

Normal. Normal push-pull output

0x1 : OPEN_DRAIN

Open-drain. Simulated open-drain output (high drive disabled).

End of enumeration elements list.


PIO0_22

Digital I/O control for port 0 pins PIO0_22
address_offset : 0x58 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO0_22 PIO0_22 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE SLEW INVERT DIGIMODE OD

FUNC : Selects pin function.
bits : 0 - 3 (4 bit)
access : read-write

Enumeration:

0 : ALT0

Alternative connection 0.

0x1 : ALT1

Alternative connection 1.

0x2 : ALT2

Alternative connection 2.

0x3 : ALT3

Alternative connection 3.

0x4 : ALT4

Alternative connection 4.

0x5 : ALT5

Alternative connection 5.

0x6 : ALT6

Alternative connection 6.

0x7 : ALT7

Alternative connection 7.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : INACTIVE

Inactive. Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN

Pull-down. Pull-down resistor enabled.

0x2 : PULL_UP

Pull-up. Pull-up resistor enabled.

0x3 : REPEATER

Repeater. Repeater mode.

End of enumeration elements list.

SLEW : Driver slew rate.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

0 : STANDARD

Standard-mode, output slew rate is slower. More outputs can be switched simultaneously.

0x1 : FAST

Fast-mode, output slew rate is faster. Refer to the appropriate specific device data sheet for details.

End of enumeration elements list.

INVERT : Input polarity.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

0 : DISABLED

Disabled. Input function is not inverted.

0x1 : ENABLED

Enabled. Input is function inverted.

End of enumeration elements list.

DIGIMODE : Select Digital mode.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

0 : ANALOG

Disable digital mode. Digital input set to 0.

0x1 : DIGITAL

Enable Digital mode. Digital input is enabled.

End of enumeration elements list.

OD : Controls open-drain mode.
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

0 : NORMAL

Normal. Normal push-pull output

0x1 : OPEN_DRAIN

Open-drain. Simulated open-drain output (high drive disabled).

End of enumeration elements list.


PIO0_23

Digital I/O control for port 0 pins PIO0_23
address_offset : 0x5C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO0_23 PIO0_23 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE SLEW INVERT DIGIMODE OD ASW

FUNC : Selects pin function.
bits : 0 - 3 (4 bit)
access : read-write

Enumeration:

0 : ALT0

Alternative connection 0.

0x1 : ALT1

Alternative connection 1.

0x2 : ALT2

Alternative connection 2.

0x3 : ALT3

Alternative connection 3.

0x4 : ALT4

Alternative connection 4.

0x5 : ALT5

Alternative connection 5.

0x6 : ALT6

Alternative connection 6.

0x7 : ALT7

Alternative connection 7.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : INACTIVE

Inactive. Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN

Pull-down. Pull-down resistor enabled.

0x2 : PULL_UP

Pull-up. Pull-up resistor enabled.

0x3 : REPEATER

Repeater. Repeater mode.

End of enumeration elements list.

SLEW : Driver slew rate.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

0 : STANDARD

Standard-mode, output slew rate is slower. More outputs can be switched simultaneously.

0x1 : FAST

Fast-mode, output slew rate is faster. Refer to the appropriate specific device data sheet for details.

End of enumeration elements list.

INVERT : Input polarity.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

0 : DISABLED

Disabled. Input function is not inverted.

0x1 : ENABLED

Enabled. Input is function inverted.

End of enumeration elements list.

DIGIMODE : Select Digital mode.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

0 : ANALOG

Disable digital mode. Digital input set to 0.

0x1 : DIGITAL

Enable Digital mode. Digital input is enabled.

End of enumeration elements list.

OD : Controls open-drain mode.
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

0 : NORMAL

Normal. Normal push-pull output

0x1 : OPEN_DRAIN

Open-drain. Simulated open-drain output (high drive disabled).

End of enumeration elements list.

ASW : Analog switch input control.
bits : 10 - 10 (1 bit)
access : read-write

Enumeration:

0 : VALUE0

For pins PIO0_9, PIO0_11, PIO0_12, PIO0_15, PIO0_18, PIO0_31, PIO1_0 and PIO1_9, analog switch is closed (enabled). For the other pins, analog switch is open (disabled).

0x1 : VALUE1

For all pins except PIO0_9, PIO0_11, PIO0_12, PIO0_15, PIO0_18, PIO0_31, PIO1_0 and PIO1_9 analog switch is closed (enabled)

End of enumeration elements list.


PIO0_24

Digital I/O control for port 0 pins PIO0_24
address_offset : 0x60 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO0_24 PIO0_24 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE SLEW INVERT DIGIMODE OD

FUNC : Selects pin function.
bits : 0 - 3 (4 bit)
access : read-write

Enumeration:

0 : ALT0

Alternative connection 0.

0x1 : ALT1

Alternative connection 1.

0x2 : ALT2

Alternative connection 2.

0x3 : ALT3

Alternative connection 3.

0x4 : ALT4

Alternative connection 4.

0x5 : ALT5

Alternative connection 5.

0x6 : ALT6

Alternative connection 6.

0x7 : ALT7

Alternative connection 7.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : INACTIVE

Inactive. Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN

Pull-down. Pull-down resistor enabled.

0x2 : PULL_UP

Pull-up. Pull-up resistor enabled.

0x3 : REPEATER

Repeater. Repeater mode.

End of enumeration elements list.

SLEW : Driver slew rate.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

0 : STANDARD

Standard-mode, output slew rate is slower. More outputs can be switched simultaneously.

0x1 : FAST

Fast-mode, output slew rate is faster. Refer to the appropriate specific device data sheet for details.

End of enumeration elements list.

INVERT : Input polarity.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

0 : DISABLED

Disabled. Input function is not inverted.

0x1 : ENABLED

Enabled. Input is function inverted.

End of enumeration elements list.

DIGIMODE : Select Digital mode.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

0 : ANALOG

Disable digital mode. Digital input set to 0.

0x1 : DIGITAL

Enable Digital mode. Digital input is enabled.

End of enumeration elements list.

OD : Controls open-drain mode.
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

0 : NORMAL

Normal. Normal push-pull output

0x1 : OPEN_DRAIN

Open-drain. Simulated open-drain output (high drive disabled).

End of enumeration elements list.


PIO0_25

Digital I/O control for port 0 pins PIO0_25
address_offset : 0x64 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO0_25 PIO0_25 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE SLEW INVERT DIGIMODE OD

FUNC : Selects pin function.
bits : 0 - 3 (4 bit)
access : read-write

Enumeration:

0 : ALT0

Alternative connection 0.

0x1 : ALT1

Alternative connection 1.

0x2 : ALT2

Alternative connection 2.

0x3 : ALT3

Alternative connection 3.

0x4 : ALT4

Alternative connection 4.

0x5 : ALT5

Alternative connection 5.

0x6 : ALT6

Alternative connection 6.

0x7 : ALT7

Alternative connection 7.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : INACTIVE

Inactive. Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN

Pull-down. Pull-down resistor enabled.

0x2 : PULL_UP

Pull-up. Pull-up resistor enabled.

0x3 : REPEATER

Repeater. Repeater mode.

End of enumeration elements list.

SLEW : Driver slew rate.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

0 : STANDARD

Standard-mode, output slew rate is slower. More outputs can be switched simultaneously.

0x1 : FAST

Fast-mode, output slew rate is faster. Refer to the appropriate specific device data sheet for details.

End of enumeration elements list.

INVERT : Input polarity.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

0 : DISABLED

Disabled. Input function is not inverted.

0x1 : ENABLED

Enabled. Input is function inverted.

End of enumeration elements list.

DIGIMODE : Select Digital mode.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

0 : ANALOG

Disable digital mode. Digital input set to 0.

0x1 : DIGITAL

Enable Digital mode. Digital input is enabled.

End of enumeration elements list.

OD : Controls open-drain mode.
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

0 : NORMAL

Normal. Normal push-pull output

0x1 : OPEN_DRAIN

Open-drain. Simulated open-drain output (high drive disabled).

End of enumeration elements list.


PIO0_26

Digital I/O control for port 0 pins PIO0_26
address_offset : 0x68 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO0_26 PIO0_26 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE SLEW INVERT DIGIMODE OD

FUNC : Selects pin function.
bits : 0 - 3 (4 bit)
access : read-write

Enumeration:

0 : ALT0

Alternative connection 0.

0x1 : ALT1

Alternative connection 1.

0x2 : ALT2

Alternative connection 2.

0x3 : ALT3

Alternative connection 3.

0x4 : ALT4

Alternative connection 4.

0x5 : ALT5

Alternative connection 5.

0x6 : ALT6

Alternative connection 6.

0x7 : ALT7

Alternative connection 7.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : INACTIVE

Inactive. Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN

Pull-down. Pull-down resistor enabled.

0x2 : PULL_UP

Pull-up. Pull-up resistor enabled.

0x3 : REPEATER

Repeater. Repeater mode.

End of enumeration elements list.

SLEW : Driver slew rate.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

0 : STANDARD

Standard-mode, output slew rate is slower. More outputs can be switched simultaneously.

0x1 : FAST

Fast-mode, output slew rate is faster. Refer to the appropriate specific device data sheet for details.

End of enumeration elements list.

INVERT : Input polarity.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

0 : DISABLED

Disabled. Input function is not inverted.

0x1 : ENABLED

Enabled. Input is function inverted.

End of enumeration elements list.

DIGIMODE : Select Digital mode.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

0 : ANALOG

Disable digital mode. Digital input set to 0.

0x1 : DIGITAL

Enable Digital mode. Digital input is enabled.

End of enumeration elements list.

OD : Controls open-drain mode.
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

0 : NORMAL

Normal. Normal push-pull output

0x1 : OPEN_DRAIN

Open-drain. Simulated open-drain output (high drive disabled).

End of enumeration elements list.


PIO0_27

Digital I/O control for port 0 pins PIO0_27
address_offset : 0x6C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO0_27 PIO0_27 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE SLEW INVERT DIGIMODE OD

FUNC : Selects pin function.
bits : 0 - 3 (4 bit)
access : read-write

Enumeration:

0 : ALT0

Alternative connection 0.

0x1 : ALT1

Alternative connection 1.

0x2 : ALT2

Alternative connection 2.

0x3 : ALT3

Alternative connection 3.

0x4 : ALT4

Alternative connection 4.

0x5 : ALT5

Alternative connection 5.

0x6 : ALT6

Alternative connection 6.

0x7 : ALT7

Alternative connection 7.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : INACTIVE

Inactive. Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN

Pull-down. Pull-down resistor enabled.

0x2 : PULL_UP

Pull-up. Pull-up resistor enabled.

0x3 : REPEATER

Repeater. Repeater mode.

End of enumeration elements list.

SLEW : Driver slew rate.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

0 : STANDARD

Standard-mode, output slew rate is slower. More outputs can be switched simultaneously.

0x1 : FAST

Fast-mode, output slew rate is faster. Refer to the appropriate specific device data sheet for details.

End of enumeration elements list.

INVERT : Input polarity.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

0 : DISABLED

Disabled. Input function is not inverted.

0x1 : ENABLED

Enabled. Input is function inverted.

End of enumeration elements list.

DIGIMODE : Select Digital mode.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

0 : ANALOG

Disable digital mode. Digital input set to 0.

0x1 : DIGITAL

Enable Digital mode. Digital input is enabled.

End of enumeration elements list.

OD : Controls open-drain mode.
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

0 : NORMAL

Normal. Normal push-pull output

0x1 : OPEN_DRAIN

Open-drain. Simulated open-drain output (high drive disabled).

End of enumeration elements list.


PIO0_28

Digital I/O control for port 0 pins PIO0_28
address_offset : 0x70 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO0_28 PIO0_28 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE SLEW INVERT DIGIMODE OD

FUNC : Selects pin function.
bits : 0 - 3 (4 bit)
access : read-write

Enumeration:

0 : ALT0

Alternative connection 0.

0x1 : ALT1

Alternative connection 1.

0x2 : ALT2

Alternative connection 2.

0x3 : ALT3

Alternative connection 3.

0x4 : ALT4

Alternative connection 4.

0x5 : ALT5

Alternative connection 5.

0x6 : ALT6

Alternative connection 6.

0x7 : ALT7

Alternative connection 7.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : INACTIVE

Inactive. Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN

Pull-down. Pull-down resistor enabled.

0x2 : PULL_UP

Pull-up. Pull-up resistor enabled.

0x3 : REPEATER

Repeater. Repeater mode.

End of enumeration elements list.

SLEW : Driver slew rate.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

0 : STANDARD

Standard-mode, output slew rate is slower. More outputs can be switched simultaneously.

0x1 : FAST

Fast-mode, output slew rate is faster. Refer to the appropriate specific device data sheet for details.

End of enumeration elements list.

INVERT : Input polarity.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

0 : DISABLED

Disabled. Input function is not inverted.

0x1 : ENABLED

Enabled. Input is function inverted.

End of enumeration elements list.

DIGIMODE : Select Digital mode.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

0 : ANALOG

Disable digital mode. Digital input set to 0.

0x1 : DIGITAL

Enable Digital mode. Digital input is enabled.

End of enumeration elements list.

OD : Controls open-drain mode.
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

0 : NORMAL

Normal. Normal push-pull output

0x1 : OPEN_DRAIN

Open-drain. Simulated open-drain output (high drive disabled).

End of enumeration elements list.


PIO0_29

Digital I/O control for port 0 pins PIO0_29
address_offset : 0x74 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO0_29 PIO0_29 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE SLEW INVERT DIGIMODE OD

FUNC : Selects pin function.
bits : 0 - 3 (4 bit)
access : read-write

Enumeration:

0 : ALT0

Alternative connection 0.

0x1 : ALT1

Alternative connection 1.

0x2 : ALT2

Alternative connection 2.

0x3 : ALT3

Alternative connection 3.

0x4 : ALT4

Alternative connection 4.

0x5 : ALT5

Alternative connection 5.

0x6 : ALT6

Alternative connection 6.

0x7 : ALT7

Alternative connection 7.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : INACTIVE

Inactive. Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN

Pull-down. Pull-down resistor enabled.

0x2 : PULL_UP

Pull-up. Pull-up resistor enabled.

0x3 : REPEATER

Repeater. Repeater mode.

End of enumeration elements list.

SLEW : Driver slew rate.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

0 : STANDARD

Standard-mode, output slew rate is slower. More outputs can be switched simultaneously.

0x1 : FAST

Fast-mode, output slew rate is faster. Refer to the appropriate specific device data sheet for details.

End of enumeration elements list.

INVERT : Input polarity.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

0 : DISABLED

Disabled. Input function is not inverted.

0x1 : ENABLED

Enabled. Input is function inverted.

End of enumeration elements list.

DIGIMODE : Select Digital mode.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

0 : ANALOG

Disable digital mode. Digital input set to 0.

0x1 : DIGITAL

Enable Digital mode. Digital input is enabled.

End of enumeration elements list.

OD : Controls open-drain mode.
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

0 : NORMAL

Normal. Normal push-pull output

0x1 : OPEN_DRAIN

Open-drain. Simulated open-drain output (high drive disabled).

End of enumeration elements list.


PIO0_30

Digital I/O control for port 0 pins PIO0_30
address_offset : 0x78 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO0_30 PIO0_30 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE SLEW INVERT DIGIMODE OD

FUNC : Selects pin function.
bits : 0 - 3 (4 bit)
access : read-write

Enumeration:

0 : ALT0

Alternative connection 0.

0x1 : ALT1

Alternative connection 1.

0x2 : ALT2

Alternative connection 2.

0x3 : ALT3

Alternative connection 3.

0x4 : ALT4

Alternative connection 4.

0x5 : ALT5

Alternative connection 5.

0x6 : ALT6

Alternative connection 6.

0x7 : ALT7

Alternative connection 7.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : INACTIVE

Inactive. Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN

Pull-down. Pull-down resistor enabled.

0x2 : PULL_UP

Pull-up. Pull-up resistor enabled.

0x3 : REPEATER

Repeater. Repeater mode.

End of enumeration elements list.

SLEW : Driver slew rate.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

0 : STANDARD

Standard-mode, output slew rate is slower. More outputs can be switched simultaneously.

0x1 : FAST

Fast-mode, output slew rate is faster. Refer to the appropriate specific device data sheet for details.

End of enumeration elements list.

INVERT : Input polarity.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

0 : DISABLED

Disabled. Input function is not inverted.

0x1 : ENABLED

Enabled. Input is function inverted.

End of enumeration elements list.

DIGIMODE : Select Digital mode.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

0 : ANALOG

Disable digital mode. Digital input set to 0.

0x1 : DIGITAL

Enable Digital mode. Digital input is enabled.

End of enumeration elements list.

OD : Controls open-drain mode.
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

0 : NORMAL

Normal. Normal push-pull output

0x1 : OPEN_DRAIN

Open-drain. Simulated open-drain output (high drive disabled).

End of enumeration elements list.


PIO0_31

Digital I/O control for port 0 pins PIO0_31
address_offset : 0x7C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO0_31 PIO0_31 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE SLEW INVERT DIGIMODE OD ASW

FUNC : Selects pin function.
bits : 0 - 3 (4 bit)
access : read-write

Enumeration:

0 : ALT0

Alternative connection 0.

0x1 : ALT1

Alternative connection 1.

0x2 : ALT2

Alternative connection 2.

0x3 : ALT3

Alternative connection 3.

0x4 : ALT4

Alternative connection 4.

0x5 : ALT5

Alternative connection 5.

0x6 : ALT6

Alternative connection 6.

0x7 : ALT7

Alternative connection 7.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : INACTIVE

Inactive. Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN

Pull-down. Pull-down resistor enabled.

0x2 : PULL_UP

Pull-up. Pull-up resistor enabled.

0x3 : REPEATER

Repeater. Repeater mode.

End of enumeration elements list.

SLEW : Driver slew rate.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

0 : STANDARD

Standard-mode, output slew rate is slower. More outputs can be switched simultaneously.

0x1 : FAST

Fast-mode, output slew rate is faster. Refer to the appropriate specific device data sheet for details.

End of enumeration elements list.

INVERT : Input polarity.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

0 : DISABLED

Disabled. Input function is not inverted.

0x1 : ENABLED

Enabled. Input is function inverted.

End of enumeration elements list.

DIGIMODE : Select Digital mode.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

0 : ANALOG

Disable digital mode. Digital input set to 0.

0x1 : DIGITAL

Enable Digital mode. Digital input is enabled.

End of enumeration elements list.

OD : Controls open-drain mode.
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

0 : NORMAL

Normal. Normal push-pull output

0x1 : OPEN_DRAIN

Open-drain. Simulated open-drain output (high drive disabled).

End of enumeration elements list.

ASW : Analog switch input control.
bits : 10 - 10 (1 bit)
access : read-write

Enumeration:

0 : VALUE0

For pins PIO0_9, PIO0_11, PIO0_12, PIO0_15, PIO0_18, PIO0_31, PIO1_0 and PIO1_9, analog switch is closed (enabled). For the other pins, analog switch is open (disabled).

0x1 : VALUE1

For all pins except PIO0_9, PIO0_11, PIO0_12, PIO0_15, PIO0_18, PIO0_31, PIO1_0 and PIO1_9 analog switch is closed (enabled)

End of enumeration elements list.


PIO0_2

Digital I/O control for port 0 pins PIO0_2
address_offset : 0x8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO0_2 PIO0_2 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE SLEW INVERT DIGIMODE OD

FUNC : Selects pin function.
bits : 0 - 3 (4 bit)
access : read-write

Enumeration:

0 : ALT0

Alternative connection 0.

0x1 : ALT1

Alternative connection 1.

0x2 : ALT2

Alternative connection 2.

0x3 : ALT3

Alternative connection 3.

0x4 : ALT4

Alternative connection 4.

0x5 : ALT5

Alternative connection 5.

0x6 : ALT6

Alternative connection 6.

0x7 : ALT7

Alternative connection 7.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : INACTIVE

Inactive. Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN

Pull-down. Pull-down resistor enabled.

0x2 : PULL_UP

Pull-up. Pull-up resistor enabled.

0x3 : REPEATER

Repeater. Repeater mode.

End of enumeration elements list.

SLEW : Driver slew rate.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

0 : STANDARD

Standard-mode, output slew rate is slower. More outputs can be switched simultaneously.

0x1 : FAST

Fast-mode, output slew rate is faster. Refer to the appropriate specific device data sheet for details.

End of enumeration elements list.

INVERT : Input polarity.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

0 : DISABLED

Disabled. Input function is not inverted.

0x1 : ENABLED

Enabled. Input is function inverted.

End of enumeration elements list.

DIGIMODE : Select Digital mode.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

0 : ANALOG

Disable digital mode. Digital input set to 0.

0x1 : DIGITAL

Enable Digital mode. Digital input is enabled.

End of enumeration elements list.

OD : Controls open-drain mode.
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

0 : NORMAL

Normal. Normal push-pull output

0x1 : OPEN_DRAIN

Open-drain. Simulated open-drain output (high drive disabled).

End of enumeration elements list.


PIO1_0

Digital I/O control for port 1 pins PIO1_0
address_offset : 0x80 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO1_0 PIO1_0 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE SLEW INVERT DIGIMODE OD ASW

FUNC : Selects pin function.
bits : 0 - 3 (4 bit)
access : read-write

Enumeration:

0 : ALT0

Alternative connection 0.

0x1 : ALT1

Alternative connection 1.

0x2 : ALT2

Alternative connection 2.

0x3 : ALT3

Alternative connection 3.

0x4 : ALT4

Alternative connection 4.

0x5 : ALT5

Alternative connection 5.

0x6 : ALT6

Alternative connection 6.

0x7 : ALT7

Alternative connection 7.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : INACTIVE

Inactive. Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN

Pull-down. Pull-down resistor enabled.

0x2 : PULL_UP

Pull-up. Pull-up resistor enabled.

0x3 : REPEATER

Repeater. Repeater mode.

End of enumeration elements list.

SLEW : Driver slew rate.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

0 : STANDARD

Standard-mode, output slew rate is slower. More outputs can be switched simultaneously.

0x1 : FAST

Fast-mode, output slew rate is faster. Refer to the appropriate specific device data sheet for details.

End of enumeration elements list.

INVERT : Input polarity.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

0 : DISABLED

Disabled. Input function is not inverted.

0x1 : ENABLED

Enabled. Input is function inverted.

End of enumeration elements list.

DIGIMODE : Select Digital mode.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

0 : ANALOG

Disable digital mode. Digital input set to 0.

0x1 : DIGITAL

Enable Digital mode. Digital input is enabled.

End of enumeration elements list.

OD : Controls open-drain mode.
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

0 : NORMAL

Normal. Normal push-pull output

0x1 : OPEN_DRAIN

Open-drain. Simulated open-drain output (high drive disabled).

End of enumeration elements list.

ASW : Analog switch input control.
bits : 10 - 10 (1 bit)
access : read-write

Enumeration:

0 : VALUE0

For pins PIO0_9, PIO0_11, PIO0_12, PIO0_15, PIO0_18, PIO0_31, PIO1_0 and PIO1_9, analog switch is closed (enabled). For the other pins, analog switch is open (disabled).

0x1 : VALUE1

For all pins except PIO0_9, PIO0_11, PIO0_12, PIO0_15, PIO0_18, PIO0_31, PIO1_0 and PIO1_9 analog switch is closed (enabled)

End of enumeration elements list.


PIO1_1

Digital I/O control for port 1 pins PIO1_1
address_offset : 0x84 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO1_1 PIO1_1 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE SLEW INVERT DIGIMODE OD

FUNC : Selects pin function.
bits : 0 - 3 (4 bit)
access : read-write

Enumeration:

0 : ALT0

Alternative connection 0.

0x1 : ALT1

Alternative connection 1.

0x2 : ALT2

Alternative connection 2.

0x3 : ALT3

Alternative connection 3.

0x4 : ALT4

Alternative connection 4.

0x5 : ALT5

Alternative connection 5.

0x6 : ALT6

Alternative connection 6.

0x7 : ALT7

Alternative connection 7.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : INACTIVE

Inactive. Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN

Pull-down. Pull-down resistor enabled.

0x2 : PULL_UP

Pull-up. Pull-up resistor enabled.

0x3 : REPEATER

Repeater. Repeater mode.

End of enumeration elements list.

SLEW : Driver slew rate.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

0 : STANDARD

Standard-mode, output slew rate is slower. More outputs can be switched simultaneously.

0x1 : FAST

Fast-mode, output slew rate is faster. Refer to the appropriate specific device data sheet for details.

End of enumeration elements list.

INVERT : Input polarity.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

0 : DISABLED

Disabled. Input function is not inverted.

0x1 : ENABLED

Enabled. Input is function inverted.

End of enumeration elements list.

DIGIMODE : Select Digital mode.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

0 : ANALOG

Disable digital mode. Digital input set to 0.

0x1 : DIGITAL

Enable Digital mode. Digital input is enabled.

End of enumeration elements list.

OD : Controls open-drain mode.
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

0 : NORMAL

Normal. Normal push-pull output

0x1 : OPEN_DRAIN

Open-drain. Simulated open-drain output (high drive disabled).

End of enumeration elements list.


PIO1_2

Digital I/O control for port 1 pins PIO1_2
address_offset : 0x88 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO1_2 PIO1_2 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE SLEW INVERT DIGIMODE OD

FUNC : Selects pin function.
bits : 0 - 3 (4 bit)
access : read-write

Enumeration:

0 : ALT0

Alternative connection 0.

0x1 : ALT1

Alternative connection 1.

0x2 : ALT2

Alternative connection 2.

0x3 : ALT3

Alternative connection 3.

0x4 : ALT4

Alternative connection 4.

0x5 : ALT5

Alternative connection 5.

0x6 : ALT6

Alternative connection 6.

0x7 : ALT7

Alternative connection 7.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : INACTIVE

Inactive. Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN

Pull-down. Pull-down resistor enabled.

0x2 : PULL_UP

Pull-up. Pull-up resistor enabled.

0x3 : REPEATER

Repeater. Repeater mode.

End of enumeration elements list.

SLEW : Driver slew rate.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

0 : STANDARD

Standard-mode, output slew rate is slower. More outputs can be switched simultaneously.

0x1 : FAST

Fast-mode, output slew rate is faster. Refer to the appropriate specific device data sheet for details.

End of enumeration elements list.

INVERT : Input polarity.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

0 : DISABLED

Disabled. Input function is not inverted.

0x1 : ENABLED

Enabled. Input is function inverted.

End of enumeration elements list.

DIGIMODE : Select Digital mode.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

0 : ANALOG

Disable digital mode. Digital input set to 0.

0x1 : DIGITAL

Enable Digital mode. Digital input is enabled.

End of enumeration elements list.

OD : Controls open-drain mode.
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

0 : NORMAL

Normal. Normal push-pull output

0x1 : OPEN_DRAIN

Open-drain. Simulated open-drain output (high drive disabled).

End of enumeration elements list.


PIO1_3

Digital I/O control for port 1 pins PIO1_3
address_offset : 0x8C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO1_3 PIO1_3 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE SLEW INVERT DIGIMODE OD

FUNC : Selects pin function.
bits : 0 - 3 (4 bit)
access : read-write

Enumeration:

0 : ALT0

Alternative connection 0.

0x1 : ALT1

Alternative connection 1.

0x2 : ALT2

Alternative connection 2.

0x3 : ALT3

Alternative connection 3.

0x4 : ALT4

Alternative connection 4.

0x5 : ALT5

Alternative connection 5.

0x6 : ALT6

Alternative connection 6.

0x7 : ALT7

Alternative connection 7.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : INACTIVE

Inactive. Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN

Pull-down. Pull-down resistor enabled.

0x2 : PULL_UP

Pull-up. Pull-up resistor enabled.

0x3 : REPEATER

Repeater. Repeater mode.

End of enumeration elements list.

SLEW : Driver slew rate.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

0 : STANDARD

Standard-mode, output slew rate is slower. More outputs can be switched simultaneously.

0x1 : FAST

Fast-mode, output slew rate is faster. Refer to the appropriate specific device data sheet for details.

End of enumeration elements list.

INVERT : Input polarity.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

0 : DISABLED

Disabled. Input function is not inverted.

0x1 : ENABLED

Enabled. Input is function inverted.

End of enumeration elements list.

DIGIMODE : Select Digital mode.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

0 : ANALOG

Disable digital mode. Digital input set to 0.

0x1 : DIGITAL

Enable Digital mode. Digital input is enabled.

End of enumeration elements list.

OD : Controls open-drain mode.
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

0 : NORMAL

Normal. Normal push-pull output

0x1 : OPEN_DRAIN

Open-drain. Simulated open-drain output (high drive disabled).

End of enumeration elements list.


PIO1_4

Digital I/O control for port 1 pins PIO1_4
address_offset : 0x90 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO1_4 PIO1_4 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE SLEW INVERT DIGIMODE OD

FUNC : Selects pin function.
bits : 0 - 3 (4 bit)
access : read-write

Enumeration:

0 : ALT0

Alternative connection 0.

0x1 : ALT1

Alternative connection 1.

0x2 : ALT2

Alternative connection 2.

0x3 : ALT3

Alternative connection 3.

0x4 : ALT4

Alternative connection 4.

0x5 : ALT5

Alternative connection 5.

0x6 : ALT6

Alternative connection 6.

0x7 : ALT7

Alternative connection 7.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : INACTIVE

Inactive. Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN

Pull-down. Pull-down resistor enabled.

0x2 : PULL_UP

Pull-up. Pull-up resistor enabled.

0x3 : REPEATER

Repeater. Repeater mode.

End of enumeration elements list.

SLEW : Driver slew rate.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

0 : STANDARD

Standard-mode, output slew rate is slower. More outputs can be switched simultaneously.

0x1 : FAST

Fast-mode, output slew rate is faster. Refer to the appropriate specific device data sheet for details.

End of enumeration elements list.

INVERT : Input polarity.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

0 : DISABLED

Disabled. Input function is not inverted.

0x1 : ENABLED

Enabled. Input is function inverted.

End of enumeration elements list.

DIGIMODE : Select Digital mode.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

0 : ANALOG

Disable digital mode. Digital input set to 0.

0x1 : DIGITAL

Enable Digital mode. Digital input is enabled.

End of enumeration elements list.

OD : Controls open-drain mode.
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

0 : NORMAL

Normal. Normal push-pull output

0x1 : OPEN_DRAIN

Open-drain. Simulated open-drain output (high drive disabled).

End of enumeration elements list.


PIO1_5

Digital I/O control for port 1 pins PIO1_5
address_offset : 0x94 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO1_5 PIO1_5 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE SLEW INVERT DIGIMODE OD

FUNC : Selects pin function.
bits : 0 - 3 (4 bit)
access : read-write

Enumeration:

0 : ALT0

Alternative connection 0.

0x1 : ALT1

Alternative connection 1.

0x2 : ALT2

Alternative connection 2.

0x3 : ALT3

Alternative connection 3.

0x4 : ALT4

Alternative connection 4.

0x5 : ALT5

Alternative connection 5.

0x6 : ALT6

Alternative connection 6.

0x7 : ALT7

Alternative connection 7.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : INACTIVE

Inactive. Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN

Pull-down. Pull-down resistor enabled.

0x2 : PULL_UP

Pull-up. Pull-up resistor enabled.

0x3 : REPEATER

Repeater. Repeater mode.

End of enumeration elements list.

SLEW : Driver slew rate.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

0 : STANDARD

Standard-mode, output slew rate is slower. More outputs can be switched simultaneously.

0x1 : FAST

Fast-mode, output slew rate is faster. Refer to the appropriate specific device data sheet for details.

End of enumeration elements list.

INVERT : Input polarity.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

0 : DISABLED

Disabled. Input function is not inverted.

0x1 : ENABLED

Enabled. Input is function inverted.

End of enumeration elements list.

DIGIMODE : Select Digital mode.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

0 : ANALOG

Disable digital mode. Digital input set to 0.

0x1 : DIGITAL

Enable Digital mode. Digital input is enabled.

End of enumeration elements list.

OD : Controls open-drain mode.
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

0 : NORMAL

Normal. Normal push-pull output

0x1 : OPEN_DRAIN

Open-drain. Simulated open-drain output (high drive disabled).

End of enumeration elements list.


PIO1_6

Digital I/O control for port 1 pins PIO1_6
address_offset : 0x98 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO1_6 PIO1_6 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE SLEW INVERT DIGIMODE OD

FUNC : Selects pin function.
bits : 0 - 3 (4 bit)
access : read-write

Enumeration:

0 : ALT0

Alternative connection 0.

0x1 : ALT1

Alternative connection 1.

0x2 : ALT2

Alternative connection 2.

0x3 : ALT3

Alternative connection 3.

0x4 : ALT4

Alternative connection 4.

0x5 : ALT5

Alternative connection 5.

0x6 : ALT6

Alternative connection 6.

0x7 : ALT7

Alternative connection 7.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : INACTIVE

Inactive. Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN

Pull-down. Pull-down resistor enabled.

0x2 : PULL_UP

Pull-up. Pull-up resistor enabled.

0x3 : REPEATER

Repeater. Repeater mode.

End of enumeration elements list.

SLEW : Driver slew rate.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

0 : STANDARD

Standard-mode, output slew rate is slower. More outputs can be switched simultaneously.

0x1 : FAST

Fast-mode, output slew rate is faster. Refer to the appropriate specific device data sheet for details.

End of enumeration elements list.

INVERT : Input polarity.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

0 : DISABLED

Disabled. Input function is not inverted.

0x1 : ENABLED

Enabled. Input is function inverted.

End of enumeration elements list.

DIGIMODE : Select Digital mode.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

0 : ANALOG

Disable digital mode. Digital input set to 0.

0x1 : DIGITAL

Enable Digital mode. Digital input is enabled.

End of enumeration elements list.

OD : Controls open-drain mode.
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

0 : NORMAL

Normal. Normal push-pull output

0x1 : OPEN_DRAIN

Open-drain. Simulated open-drain output (high drive disabled).

End of enumeration elements list.


PIO1_7

Digital I/O control for port 1 pins PIO1_7
address_offset : 0x9C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO1_7 PIO1_7 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE SLEW INVERT DIGIMODE OD

FUNC : Selects pin function.
bits : 0 - 3 (4 bit)
access : read-write

Enumeration:

0 : ALT0

Alternative connection 0.

0x1 : ALT1

Alternative connection 1.

0x2 : ALT2

Alternative connection 2.

0x3 : ALT3

Alternative connection 3.

0x4 : ALT4

Alternative connection 4.

0x5 : ALT5

Alternative connection 5.

0x6 : ALT6

Alternative connection 6.

0x7 : ALT7

Alternative connection 7.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : INACTIVE

Inactive. Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN

Pull-down. Pull-down resistor enabled.

0x2 : PULL_UP

Pull-up. Pull-up resistor enabled.

0x3 : REPEATER

Repeater. Repeater mode.

End of enumeration elements list.

SLEW : Driver slew rate.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

0 : STANDARD

Standard-mode, output slew rate is slower. More outputs can be switched simultaneously.

0x1 : FAST

Fast-mode, output slew rate is faster. Refer to the appropriate specific device data sheet for details.

End of enumeration elements list.

INVERT : Input polarity.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

0 : DISABLED

Disabled. Input function is not inverted.

0x1 : ENABLED

Enabled. Input is function inverted.

End of enumeration elements list.

DIGIMODE : Select Digital mode.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

0 : ANALOG

Disable digital mode. Digital input set to 0.

0x1 : DIGITAL

Enable Digital mode. Digital input is enabled.

End of enumeration elements list.

OD : Controls open-drain mode.
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

0 : NORMAL

Normal. Normal push-pull output

0x1 : OPEN_DRAIN

Open-drain. Simulated open-drain output (high drive disabled).

End of enumeration elements list.


PIO1_8

Digital I/O control for port 1 pins PIO1_8
address_offset : 0xA0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO1_8 PIO1_8 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE SLEW INVERT DIGIMODE OD ASW

FUNC : Selects pin function.
bits : 0 - 3 (4 bit)
access : read-write

Enumeration:

0 : ALT0

Alternative connection 0.

0x1 : ALT1

Alternative connection 1.

0x2 : ALT2

Alternative connection 2.

0x3 : ALT3

Alternative connection 3.

0x4 : ALT4

Alternative connection 4.

0x5 : ALT5

Alternative connection 5.

0x6 : ALT6

Alternative connection 6.

0x7 : ALT7

Alternative connection 7.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : INACTIVE

Inactive. Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN

Pull-down. Pull-down resistor enabled.

0x2 : PULL_UP

Pull-up. Pull-up resistor enabled.

0x3 : REPEATER

Repeater. Repeater mode.

End of enumeration elements list.

SLEW : Driver slew rate.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

0 : STANDARD

Standard-mode, output slew rate is slower. More outputs can be switched simultaneously.

0x1 : FAST

Fast-mode, output slew rate is faster. Refer to the appropriate specific device data sheet for details.

End of enumeration elements list.

INVERT : Input polarity.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

0 : DISABLED

Disabled. Input function is not inverted.

0x1 : ENABLED

Enabled. Input is function inverted.

End of enumeration elements list.

DIGIMODE : Select Digital mode.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

0 : ANALOG

Disable digital mode. Digital input set to 0.

0x1 : DIGITAL

Enable Digital mode. Digital input is enabled.

End of enumeration elements list.

OD : Controls open-drain mode.
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

0 : NORMAL

Normal. Normal push-pull output

0x1 : OPEN_DRAIN

Open-drain. Simulated open-drain output (high drive disabled).

End of enumeration elements list.

ASW : Analog switch input control.
bits : 10 - 10 (1 bit)
access : read-write

Enumeration:

0 : VALUE0

For pins PIO0_9, PIO0_11, PIO0_12, PIO0_15, PIO0_18, PIO0_31, PIO1_0 and PIO1_9, analog switch is closed (enabled). For the other pins, analog switch is open (disabled).

0x1 : VALUE1

For all pins except PIO0_9, PIO0_11, PIO0_12, PIO0_15, PIO0_18, PIO0_31, PIO1_0 and PIO1_9 analog switch is closed (enabled)

End of enumeration elements list.


PIO1_9

Digital I/O control for port 1 pins PIO1_9
address_offset : 0xA4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO1_9 PIO1_9 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE SLEW INVERT DIGIMODE OD ASW

FUNC : Selects pin function.
bits : 0 - 3 (4 bit)
access : read-write

Enumeration:

0 : ALT0

Alternative connection 0.

0x1 : ALT1

Alternative connection 1.

0x2 : ALT2

Alternative connection 2.

0x3 : ALT3

Alternative connection 3.

0x4 : ALT4

Alternative connection 4.

0x5 : ALT5

Alternative connection 5.

0x6 : ALT6

Alternative connection 6.

0x7 : ALT7

Alternative connection 7.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : INACTIVE

Inactive. Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN

Pull-down. Pull-down resistor enabled.

0x2 : PULL_UP

Pull-up. Pull-up resistor enabled.

0x3 : REPEATER

Repeater. Repeater mode.

End of enumeration elements list.

SLEW : Driver slew rate.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

0 : STANDARD

Standard-mode, output slew rate is slower. More outputs can be switched simultaneously.

0x1 : FAST

Fast-mode, output slew rate is faster. Refer to the appropriate specific device data sheet for details.

End of enumeration elements list.

INVERT : Input polarity.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

0 : DISABLED

Disabled. Input function is not inverted.

0x1 : ENABLED

Enabled. Input is function inverted.

End of enumeration elements list.

DIGIMODE : Select Digital mode.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

0 : ANALOG

Disable digital mode. Digital input set to 0.

0x1 : DIGITAL

Enable Digital mode. Digital input is enabled.

End of enumeration elements list.

OD : Controls open-drain mode.
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

0 : NORMAL

Normal. Normal push-pull output

0x1 : OPEN_DRAIN

Open-drain. Simulated open-drain output (high drive disabled).

End of enumeration elements list.

ASW : Analog switch input control.
bits : 10 - 10 (1 bit)
access : read-write

Enumeration:

0 : VALUE0

For pins PIO0_9, PIO0_11, PIO0_12, PIO0_15, PIO0_18, PIO0_31, PIO1_0 and PIO1_9, analog switch is closed (enabled). For the other pins, analog switch is open (disabled).

0x1 : VALUE1

For all pins except PIO0_9, PIO0_11, PIO0_12, PIO0_15, PIO0_18, PIO0_31, PIO1_0 and PIO1_9 analog switch is closed (enabled)

End of enumeration elements list.


PIO1_10

Digital I/O control for port 1 pins PIO1_10
address_offset : 0xA8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO1_10 PIO1_10 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE SLEW INVERT DIGIMODE OD

FUNC : Selects pin function.
bits : 0 - 3 (4 bit)
access : read-write

Enumeration:

0 : ALT0

Alternative connection 0.

0x1 : ALT1

Alternative connection 1.

0x2 : ALT2

Alternative connection 2.

0x3 : ALT3

Alternative connection 3.

0x4 : ALT4

Alternative connection 4.

0x5 : ALT5

Alternative connection 5.

0x6 : ALT6

Alternative connection 6.

0x7 : ALT7

Alternative connection 7.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : INACTIVE

Inactive. Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN

Pull-down. Pull-down resistor enabled.

0x2 : PULL_UP

Pull-up. Pull-up resistor enabled.

0x3 : REPEATER

Repeater. Repeater mode.

End of enumeration elements list.

SLEW : Driver slew rate.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

0 : STANDARD

Standard-mode, output slew rate is slower. More outputs can be switched simultaneously.

0x1 : FAST

Fast-mode, output slew rate is faster. Refer to the appropriate specific device data sheet for details.

End of enumeration elements list.

INVERT : Input polarity.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

0 : DISABLED

Disabled. Input function is not inverted.

0x1 : ENABLED

Enabled. Input is function inverted.

End of enumeration elements list.

DIGIMODE : Select Digital mode.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

0 : ANALOG

Disable digital mode. Digital input set to 0.

0x1 : DIGITAL

Enable Digital mode. Digital input is enabled.

End of enumeration elements list.

OD : Controls open-drain mode.
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

0 : NORMAL

Normal. Normal push-pull output

0x1 : OPEN_DRAIN

Open-drain. Simulated open-drain output (high drive disabled).

End of enumeration elements list.


PIO1_11

Digital I/O control for port 1 pins PIO1_11
address_offset : 0xAC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO1_11 PIO1_11 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE SLEW INVERT DIGIMODE OD

FUNC : Selects pin function.
bits : 0 - 3 (4 bit)
access : read-write

Enumeration:

0 : ALT0

Alternative connection 0.

0x1 : ALT1

Alternative connection 1.

0x2 : ALT2

Alternative connection 2.

0x3 : ALT3

Alternative connection 3.

0x4 : ALT4

Alternative connection 4.

0x5 : ALT5

Alternative connection 5.

0x6 : ALT6

Alternative connection 6.

0x7 : ALT7

Alternative connection 7.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : INACTIVE

Inactive. Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN

Pull-down. Pull-down resistor enabled.

0x2 : PULL_UP

Pull-up. Pull-up resistor enabled.

0x3 : REPEATER

Repeater. Repeater mode.

End of enumeration elements list.

SLEW : Driver slew rate.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

0 : STANDARD

Standard-mode, output slew rate is slower. More outputs can be switched simultaneously.

0x1 : FAST

Fast-mode, output slew rate is faster. Refer to the appropriate specific device data sheet for details.

End of enumeration elements list.

INVERT : Input polarity.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

0 : DISABLED

Disabled. Input function is not inverted.

0x1 : ENABLED

Enabled. Input is function inverted.

End of enumeration elements list.

DIGIMODE : Select Digital mode.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

0 : ANALOG

Disable digital mode. Digital input set to 0.

0x1 : DIGITAL

Enable Digital mode. Digital input is enabled.

End of enumeration elements list.

OD : Controls open-drain mode.
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

0 : NORMAL

Normal. Normal push-pull output

0x1 : OPEN_DRAIN

Open-drain. Simulated open-drain output (high drive disabled).

End of enumeration elements list.


PIO1_12

Digital I/O control for port 1 pins PIO1_12
address_offset : 0xB0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO1_12 PIO1_12 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE SLEW INVERT DIGIMODE OD

FUNC : Selects pin function.
bits : 0 - 3 (4 bit)
access : read-write

Enumeration:

0 : ALT0

Alternative connection 0.

0x1 : ALT1

Alternative connection 1.

0x2 : ALT2

Alternative connection 2.

0x3 : ALT3

Alternative connection 3.

0x4 : ALT4

Alternative connection 4.

0x5 : ALT5

Alternative connection 5.

0x6 : ALT6

Alternative connection 6.

0x7 : ALT7

Alternative connection 7.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : INACTIVE

Inactive. Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN

Pull-down. Pull-down resistor enabled.

0x2 : PULL_UP

Pull-up. Pull-up resistor enabled.

0x3 : REPEATER

Repeater. Repeater mode.

End of enumeration elements list.

SLEW : Driver slew rate.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

0 : STANDARD

Standard-mode, output slew rate is slower. More outputs can be switched simultaneously.

0x1 : FAST

Fast-mode, output slew rate is faster. Refer to the appropriate specific device data sheet for details.

End of enumeration elements list.

INVERT : Input polarity.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

0 : DISABLED

Disabled. Input function is not inverted.

0x1 : ENABLED

Enabled. Input is function inverted.

End of enumeration elements list.

DIGIMODE : Select Digital mode.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

0 : ANALOG

Disable digital mode. Digital input set to 0.

0x1 : DIGITAL

Enable Digital mode. Digital input is enabled.

End of enumeration elements list.

OD : Controls open-drain mode.
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

0 : NORMAL

Normal. Normal push-pull output

0x1 : OPEN_DRAIN

Open-drain. Simulated open-drain output (high drive disabled).

End of enumeration elements list.


PIO1_13

Digital I/O control for port 1 pins PIO1_13
address_offset : 0xB4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO1_13 PIO1_13 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE SLEW INVERT DIGIMODE OD

FUNC : Selects pin function.
bits : 0 - 3 (4 bit)
access : read-write

Enumeration:

0 : ALT0

Alternative connection 0.

0x1 : ALT1

Alternative connection 1.

0x2 : ALT2

Alternative connection 2.

0x3 : ALT3

Alternative connection 3.

0x4 : ALT4

Alternative connection 4.

0x5 : ALT5

Alternative connection 5.

0x6 : ALT6

Alternative connection 6.

0x7 : ALT7

Alternative connection 7.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : INACTIVE

Inactive. Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN

Pull-down. Pull-down resistor enabled.

0x2 : PULL_UP

Pull-up. Pull-up resistor enabled.

0x3 : REPEATER

Repeater. Repeater mode.

End of enumeration elements list.

SLEW : Driver slew rate.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

0 : STANDARD

Standard-mode, output slew rate is slower. More outputs can be switched simultaneously.

0x1 : FAST

Fast-mode, output slew rate is faster. Refer to the appropriate specific device data sheet for details.

End of enumeration elements list.

INVERT : Input polarity.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

0 : DISABLED

Disabled. Input function is not inverted.

0x1 : ENABLED

Enabled. Input is function inverted.

End of enumeration elements list.

DIGIMODE : Select Digital mode.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

0 : ANALOG

Disable digital mode. Digital input set to 0.

0x1 : DIGITAL

Enable Digital mode. Digital input is enabled.

End of enumeration elements list.

OD : Controls open-drain mode.
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

0 : NORMAL

Normal. Normal push-pull output

0x1 : OPEN_DRAIN

Open-drain. Simulated open-drain output (high drive disabled).

End of enumeration elements list.


PIO1_14

Digital I/O control for port 1 pins PIO1_14
address_offset : 0xB8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO1_14 PIO1_14 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE SLEW INVERT DIGIMODE OD ASW

FUNC : Selects pin function.
bits : 0 - 3 (4 bit)
access : read-write

Enumeration:

0 : ALT0

Alternative connection 0.

0x1 : ALT1

Alternative connection 1.

0x2 : ALT2

Alternative connection 2.

0x3 : ALT3

Alternative connection 3.

0x4 : ALT4

Alternative connection 4.

0x5 : ALT5

Alternative connection 5.

0x6 : ALT6

Alternative connection 6.

0x7 : ALT7

Alternative connection 7.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : INACTIVE

Inactive. Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN

Pull-down. Pull-down resistor enabled.

0x2 : PULL_UP

Pull-up. Pull-up resistor enabled.

0x3 : REPEATER

Repeater. Repeater mode.

End of enumeration elements list.

SLEW : Driver slew rate.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

0 : STANDARD

Standard-mode, output slew rate is slower. More outputs can be switched simultaneously.

0x1 : FAST

Fast-mode, output slew rate is faster. Refer to the appropriate specific device data sheet for details.

End of enumeration elements list.

INVERT : Input polarity.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

0 : DISABLED

Disabled. Input function is not inverted.

0x1 : ENABLED

Enabled. Input is function inverted.

End of enumeration elements list.

DIGIMODE : Select Digital mode.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

0 : ANALOG

Disable digital mode. Digital input set to 0.

0x1 : DIGITAL

Enable Digital mode. Digital input is enabled.

End of enumeration elements list.

OD : Controls open-drain mode.
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

0 : NORMAL

Normal. Normal push-pull output

0x1 : OPEN_DRAIN

Open-drain. Simulated open-drain output (high drive disabled).

End of enumeration elements list.

ASW : Analog switch input control.
bits : 10 - 10 (1 bit)
access : read-write

Enumeration:

0 : VALUE0

For pins PIO0_9, PIO0_11, PIO0_12, PIO0_15, PIO0_18, PIO0_31, PIO1_0 and PIO1_9, analog switch is closed (enabled). For the other pins, analog switch is open (disabled).

0x1 : VALUE1

For all pins except PIO0_9, PIO0_11, PIO0_12, PIO0_15, PIO0_18, PIO0_31, PIO1_0 and PIO1_9 analog switch is closed (enabled)

End of enumeration elements list.


PIO1_15

Digital I/O control for port 1 pins PIO1_15
address_offset : 0xBC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO1_15 PIO1_15 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE SLEW INVERT DIGIMODE OD

FUNC : Selects pin function.
bits : 0 - 3 (4 bit)
access : read-write

Enumeration:

0 : ALT0

Alternative connection 0.

0x1 : ALT1

Alternative connection 1.

0x2 : ALT2

Alternative connection 2.

0x3 : ALT3

Alternative connection 3.

0x4 : ALT4

Alternative connection 4.

0x5 : ALT5

Alternative connection 5.

0x6 : ALT6

Alternative connection 6.

0x7 : ALT7

Alternative connection 7.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : INACTIVE

Inactive. Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN

Pull-down. Pull-down resistor enabled.

0x2 : PULL_UP

Pull-up. Pull-up resistor enabled.

0x3 : REPEATER

Repeater. Repeater mode.

End of enumeration elements list.

SLEW : Driver slew rate.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

0 : STANDARD

Standard-mode, output slew rate is slower. More outputs can be switched simultaneously.

0x1 : FAST

Fast-mode, output slew rate is faster. Refer to the appropriate specific device data sheet for details.

End of enumeration elements list.

INVERT : Input polarity.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

0 : DISABLED

Disabled. Input function is not inverted.

0x1 : ENABLED

Enabled. Input is function inverted.

End of enumeration elements list.

DIGIMODE : Select Digital mode.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

0 : ANALOG

Disable digital mode. Digital input set to 0.

0x1 : DIGITAL

Enable Digital mode. Digital input is enabled.

End of enumeration elements list.

OD : Controls open-drain mode.
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

0 : NORMAL

Normal. Normal push-pull output

0x1 : OPEN_DRAIN

Open-drain. Simulated open-drain output (high drive disabled).

End of enumeration elements list.


PIO0_3

Digital I/O control for port 0 pins PIO0_3
address_offset : 0xC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO0_3 PIO0_3 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE SLEW INVERT DIGIMODE OD

FUNC : Selects pin function.
bits : 0 - 3 (4 bit)
access : read-write

Enumeration:

0 : ALT0

Alternative connection 0.

0x1 : ALT1

Alternative connection 1.

0x2 : ALT2

Alternative connection 2.

0x3 : ALT3

Alternative connection 3.

0x4 : ALT4

Alternative connection 4.

0x5 : ALT5

Alternative connection 5.

0x6 : ALT6

Alternative connection 6.

0x7 : ALT7

Alternative connection 7.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : INACTIVE

Inactive. Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN

Pull-down. Pull-down resistor enabled.

0x2 : PULL_UP

Pull-up. Pull-up resistor enabled.

0x3 : REPEATER

Repeater. Repeater mode.

End of enumeration elements list.

SLEW : Driver slew rate.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

0 : STANDARD

Standard-mode, output slew rate is slower. More outputs can be switched simultaneously.

0x1 : FAST

Fast-mode, output slew rate is faster. Refer to the appropriate specific device data sheet for details.

End of enumeration elements list.

INVERT : Input polarity.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

0 : DISABLED

Disabled. Input function is not inverted.

0x1 : ENABLED

Enabled. Input is function inverted.

End of enumeration elements list.

DIGIMODE : Select Digital mode.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

0 : ANALOG

Disable digital mode. Digital input set to 0.

0x1 : DIGITAL

Enable Digital mode. Digital input is enabled.

End of enumeration elements list.

OD : Controls open-drain mode.
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

0 : NORMAL

Normal. Normal push-pull output

0x1 : OPEN_DRAIN

Open-drain. Simulated open-drain output (high drive disabled).

End of enumeration elements list.


PIO1_16

Digital I/O control for port 1 pins PIO1_16
address_offset : 0xC0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO1_16 PIO1_16 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE SLEW INVERT DIGIMODE OD

FUNC : Selects pin function.
bits : 0 - 3 (4 bit)
access : read-write

Enumeration:

0 : ALT0

Alternative connection 0.

0x1 : ALT1

Alternative connection 1.

0x2 : ALT2

Alternative connection 2.

0x3 : ALT3

Alternative connection 3.

0x4 : ALT4

Alternative connection 4.

0x5 : ALT5

Alternative connection 5.

0x6 : ALT6

Alternative connection 6.

0x7 : ALT7

Alternative connection 7.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : INACTIVE

Inactive. Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN

Pull-down. Pull-down resistor enabled.

0x2 : PULL_UP

Pull-up. Pull-up resistor enabled.

0x3 : REPEATER

Repeater. Repeater mode.

End of enumeration elements list.

SLEW : Driver slew rate.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

0 : STANDARD

Standard-mode, output slew rate is slower. More outputs can be switched simultaneously.

0x1 : FAST

Fast-mode, output slew rate is faster. Refer to the appropriate specific device data sheet for details.

End of enumeration elements list.

INVERT : Input polarity.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

0 : DISABLED

Disabled. Input function is not inverted.

0x1 : ENABLED

Enabled. Input is function inverted.

End of enumeration elements list.

DIGIMODE : Select Digital mode.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

0 : ANALOG

Disable digital mode. Digital input set to 0.

0x1 : DIGITAL

Enable Digital mode. Digital input is enabled.

End of enumeration elements list.

OD : Controls open-drain mode.
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

0 : NORMAL

Normal. Normal push-pull output

0x1 : OPEN_DRAIN

Open-drain. Simulated open-drain output (high drive disabled).

End of enumeration elements list.


PIO1_17

Digital I/O control for port 1 pins PIO1_17
address_offset : 0xC4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO1_17 PIO1_17 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE SLEW INVERT DIGIMODE OD

FUNC : Selects pin function.
bits : 0 - 3 (4 bit)
access : read-write

Enumeration:

0 : ALT0

Alternative connection 0.

0x1 : ALT1

Alternative connection 1.

0x2 : ALT2

Alternative connection 2.

0x3 : ALT3

Alternative connection 3.

0x4 : ALT4

Alternative connection 4.

0x5 : ALT5

Alternative connection 5.

0x6 : ALT6

Alternative connection 6.

0x7 : ALT7

Alternative connection 7.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : INACTIVE

Inactive. Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN

Pull-down. Pull-down resistor enabled.

0x2 : PULL_UP

Pull-up. Pull-up resistor enabled.

0x3 : REPEATER

Repeater. Repeater mode.

End of enumeration elements list.

SLEW : Driver slew rate.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

0 : STANDARD

Standard-mode, output slew rate is slower. More outputs can be switched simultaneously.

0x1 : FAST

Fast-mode, output slew rate is faster. Refer to the appropriate specific device data sheet for details.

End of enumeration elements list.

INVERT : Input polarity.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

0 : DISABLED

Disabled. Input function is not inverted.

0x1 : ENABLED

Enabled. Input is function inverted.

End of enumeration elements list.

DIGIMODE : Select Digital mode.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

0 : ANALOG

Disable digital mode. Digital input set to 0.

0x1 : DIGITAL

Enable Digital mode. Digital input is enabled.

End of enumeration elements list.

OD : Controls open-drain mode.
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

0 : NORMAL

Normal. Normal push-pull output

0x1 : OPEN_DRAIN

Open-drain. Simulated open-drain output (high drive disabled).

End of enumeration elements list.


PIO1_18

Digital I/O control for port 1 pins PIO1_18
address_offset : 0xC8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO1_18 PIO1_18 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE SLEW INVERT DIGIMODE OD

FUNC : Selects pin function.
bits : 0 - 3 (4 bit)
access : read-write

Enumeration:

0 : ALT0

Alternative connection 0.

0x1 : ALT1

Alternative connection 1.

0x2 : ALT2

Alternative connection 2.

0x3 : ALT3

Alternative connection 3.

0x4 : ALT4

Alternative connection 4.

0x5 : ALT5

Alternative connection 5.

0x6 : ALT6

Alternative connection 6.

0x7 : ALT7

Alternative connection 7.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : INACTIVE

Inactive. Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN

Pull-down. Pull-down resistor enabled.

0x2 : PULL_UP

Pull-up. Pull-up resistor enabled.

0x3 : REPEATER

Repeater. Repeater mode.

End of enumeration elements list.

SLEW : Driver slew rate.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

0 : STANDARD

Standard-mode, output slew rate is slower. More outputs can be switched simultaneously.

0x1 : FAST

Fast-mode, output slew rate is faster. Refer to the appropriate specific device data sheet for details.

End of enumeration elements list.

INVERT : Input polarity.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

0 : DISABLED

Disabled. Input function is not inverted.

0x1 : ENABLED

Enabled. Input is function inverted.

End of enumeration elements list.

DIGIMODE : Select Digital mode.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

0 : ANALOG

Disable digital mode. Digital input set to 0.

0x1 : DIGITAL

Enable Digital mode. Digital input is enabled.

End of enumeration elements list.

OD : Controls open-drain mode.
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

0 : NORMAL

Normal. Normal push-pull output

0x1 : OPEN_DRAIN

Open-drain. Simulated open-drain output (high drive disabled).

End of enumeration elements list.


PIO1_19

Digital I/O control for port 1 pins PIO1_19
address_offset : 0xCC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO1_19 PIO1_19 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE SLEW INVERT DIGIMODE OD ASW

FUNC : Selects pin function.
bits : 0 - 3 (4 bit)
access : read-write

Enumeration:

0 : ALT0

Alternative connection 0.

0x1 : ALT1

Alternative connection 1.

0x2 : ALT2

Alternative connection 2.

0x3 : ALT3

Alternative connection 3.

0x4 : ALT4

Alternative connection 4.

0x5 : ALT5

Alternative connection 5.

0x6 : ALT6

Alternative connection 6.

0x7 : ALT7

Alternative connection 7.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : INACTIVE

Inactive. Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN

Pull-down. Pull-down resistor enabled.

0x2 : PULL_UP

Pull-up. Pull-up resistor enabled.

0x3 : REPEATER

Repeater. Repeater mode.

End of enumeration elements list.

SLEW : Driver slew rate.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

0 : STANDARD

Standard-mode, output slew rate is slower. More outputs can be switched simultaneously.

0x1 : FAST

Fast-mode, output slew rate is faster. Refer to the appropriate specific device data sheet for details.

End of enumeration elements list.

INVERT : Input polarity.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

0 : DISABLED

Disabled. Input function is not inverted.

0x1 : ENABLED

Enabled. Input is function inverted.

End of enumeration elements list.

DIGIMODE : Select Digital mode.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

0 : ANALOG

Disable digital mode. Digital input set to 0.

0x1 : DIGITAL

Enable Digital mode. Digital input is enabled.

End of enumeration elements list.

OD : Controls open-drain mode.
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

0 : NORMAL

Normal. Normal push-pull output

0x1 : OPEN_DRAIN

Open-drain. Simulated open-drain output (high drive disabled).

End of enumeration elements list.

ASW : Analog switch input control.
bits : 10 - 10 (1 bit)
access : read-write

Enumeration:

0 : VALUE0

For pins PIO0_9, PIO0_11, PIO0_12, PIO0_15, PIO0_18, PIO0_31, PIO1_0 and PIO1_9, analog switch is closed (enabled). For the other pins, analog switch is open (disabled).

0x1 : VALUE1

For all pins except PIO0_9, PIO0_11, PIO0_12, PIO0_15, PIO0_18, PIO0_31, PIO1_0 and PIO1_9 analog switch is closed (enabled)

End of enumeration elements list.


PIO1_20

Digital I/O control for port 1 pins PIO1_20
address_offset : 0xD0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO1_20 PIO1_20 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE SLEW INVERT DIGIMODE OD

FUNC : Selects pin function.
bits : 0 - 3 (4 bit)
access : read-write

Enumeration:

0 : ALT0

Alternative connection 0.

0x1 : ALT1

Alternative connection 1.

0x2 : ALT2

Alternative connection 2.

0x3 : ALT3

Alternative connection 3.

0x4 : ALT4

Alternative connection 4.

0x5 : ALT5

Alternative connection 5.

0x6 : ALT6

Alternative connection 6.

0x7 : ALT7

Alternative connection 7.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : INACTIVE

Inactive. Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN

Pull-down. Pull-down resistor enabled.

0x2 : PULL_UP

Pull-up. Pull-up resistor enabled.

0x3 : REPEATER

Repeater. Repeater mode.

End of enumeration elements list.

SLEW : Driver slew rate.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

0 : STANDARD

Standard-mode, output slew rate is slower. More outputs can be switched simultaneously.

0x1 : FAST

Fast-mode, output slew rate is faster. Refer to the appropriate specific device data sheet for details.

End of enumeration elements list.

INVERT : Input polarity.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

0 : DISABLED

Disabled. Input function is not inverted.

0x1 : ENABLED

Enabled. Input is function inverted.

End of enumeration elements list.

DIGIMODE : Select Digital mode.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

0 : ANALOG

Disable digital mode. Digital input set to 0.

0x1 : DIGITAL

Enable Digital mode. Digital input is enabled.

End of enumeration elements list.

OD : Controls open-drain mode.
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

0 : NORMAL

Normal. Normal push-pull output

0x1 : OPEN_DRAIN

Open-drain. Simulated open-drain output (high drive disabled).

End of enumeration elements list.


PIO1_21

Digital I/O control for port 1 pins PIO1_21
address_offset : 0xD4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO1_21 PIO1_21 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE SLEW INVERT DIGIMODE OD

FUNC : Selects pin function.
bits : 0 - 3 (4 bit)
access : read-write

Enumeration:

0 : ALT0

Alternative connection 0.

0x1 : ALT1

Alternative connection 1.

0x2 : ALT2

Alternative connection 2.

0x3 : ALT3

Alternative connection 3.

0x4 : ALT4

Alternative connection 4.

0x5 : ALT5

Alternative connection 5.

0x6 : ALT6

Alternative connection 6.

0x7 : ALT7

Alternative connection 7.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : INACTIVE

Inactive. Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN

Pull-down. Pull-down resistor enabled.

0x2 : PULL_UP

Pull-up. Pull-up resistor enabled.

0x3 : REPEATER

Repeater. Repeater mode.

End of enumeration elements list.

SLEW : Driver slew rate.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

0 : STANDARD

Standard-mode, output slew rate is slower. More outputs can be switched simultaneously.

0x1 : FAST

Fast-mode, output slew rate is faster. Refer to the appropriate specific device data sheet for details.

End of enumeration elements list.

INVERT : Input polarity.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

0 : DISABLED

Disabled. Input function is not inverted.

0x1 : ENABLED

Enabled. Input is function inverted.

End of enumeration elements list.

DIGIMODE : Select Digital mode.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

0 : ANALOG

Disable digital mode. Digital input set to 0.

0x1 : DIGITAL

Enable Digital mode. Digital input is enabled.

End of enumeration elements list.

OD : Controls open-drain mode.
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

0 : NORMAL

Normal. Normal push-pull output

0x1 : OPEN_DRAIN

Open-drain. Simulated open-drain output (high drive disabled).

End of enumeration elements list.


PIO1_22

Digital I/O control for port 1 pins PIO1_22
address_offset : 0xD8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO1_22 PIO1_22 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE SLEW INVERT DIGIMODE OD

FUNC : Selects pin function.
bits : 0 - 3 (4 bit)
access : read-write

Enumeration:

0 : ALT0

Alternative connection 0.

0x1 : ALT1

Alternative connection 1.

0x2 : ALT2

Alternative connection 2.

0x3 : ALT3

Alternative connection 3.

0x4 : ALT4

Alternative connection 4.

0x5 : ALT5

Alternative connection 5.

0x6 : ALT6

Alternative connection 6.

0x7 : ALT7

Alternative connection 7.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : INACTIVE

Inactive. Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN

Pull-down. Pull-down resistor enabled.

0x2 : PULL_UP

Pull-up. Pull-up resistor enabled.

0x3 : REPEATER

Repeater. Repeater mode.

End of enumeration elements list.

SLEW : Driver slew rate.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

0 : STANDARD

Standard-mode, output slew rate is slower. More outputs can be switched simultaneously.

0x1 : FAST

Fast-mode, output slew rate is faster. Refer to the appropriate specific device data sheet for details.

End of enumeration elements list.

INVERT : Input polarity.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

0 : DISABLED

Disabled. Input function is not inverted.

0x1 : ENABLED

Enabled. Input is function inverted.

End of enumeration elements list.

DIGIMODE : Select Digital mode.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

0 : ANALOG

Disable digital mode. Digital input set to 0.

0x1 : DIGITAL

Enable Digital mode. Digital input is enabled.

End of enumeration elements list.

OD : Controls open-drain mode.
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

0 : NORMAL

Normal. Normal push-pull output

0x1 : OPEN_DRAIN

Open-drain. Simulated open-drain output (high drive disabled).

End of enumeration elements list.


PIO1_23

Digital I/O control for port 1 pins PIO1_23
address_offset : 0xDC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO1_23 PIO1_23 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE SLEW INVERT DIGIMODE OD

FUNC : Selects pin function.
bits : 0 - 3 (4 bit)
access : read-write

Enumeration:

0 : ALT0

Alternative connection 0.

0x1 : ALT1

Alternative connection 1.

0x2 : ALT2

Alternative connection 2.

0x3 : ALT3

Alternative connection 3.

0x4 : ALT4

Alternative connection 4.

0x5 : ALT5

Alternative connection 5.

0x6 : ALT6

Alternative connection 6.

0x7 : ALT7

Alternative connection 7.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : INACTIVE

Inactive. Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN

Pull-down. Pull-down resistor enabled.

0x2 : PULL_UP

Pull-up. Pull-up resistor enabled.

0x3 : REPEATER

Repeater. Repeater mode.

End of enumeration elements list.

SLEW : Driver slew rate.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

0 : STANDARD

Standard-mode, output slew rate is slower. More outputs can be switched simultaneously.

0x1 : FAST

Fast-mode, output slew rate is faster. Refer to the appropriate specific device data sheet for details.

End of enumeration elements list.

INVERT : Input polarity.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

0 : DISABLED

Disabled. Input function is not inverted.

0x1 : ENABLED

Enabled. Input is function inverted.

End of enumeration elements list.

DIGIMODE : Select Digital mode.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

0 : ANALOG

Disable digital mode. Digital input set to 0.

0x1 : DIGITAL

Enable Digital mode. Digital input is enabled.

End of enumeration elements list.

OD : Controls open-drain mode.
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

0 : NORMAL

Normal. Normal push-pull output

0x1 : OPEN_DRAIN

Open-drain. Simulated open-drain output (high drive disabled).

End of enumeration elements list.


PIO1_24

Digital I/O control for port 1 pins PIO1_24
address_offset : 0xE0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO1_24 PIO1_24 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE SLEW INVERT DIGIMODE OD

FUNC : Selects pin function.
bits : 0 - 3 (4 bit)
access : read-write

Enumeration:

0 : ALT0

Alternative connection 0.

0x1 : ALT1

Alternative connection 1.

0x2 : ALT2

Alternative connection 2.

0x3 : ALT3

Alternative connection 3.

0x4 : ALT4

Alternative connection 4.

0x5 : ALT5

Alternative connection 5.

0x6 : ALT6

Alternative connection 6.

0x7 : ALT7

Alternative connection 7.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : INACTIVE

Inactive. Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN

Pull-down. Pull-down resistor enabled.

0x2 : PULL_UP

Pull-up. Pull-up resistor enabled.

0x3 : REPEATER

Repeater. Repeater mode.

End of enumeration elements list.

SLEW : Driver slew rate.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

0 : STANDARD

Standard-mode, output slew rate is slower. More outputs can be switched simultaneously.

0x1 : FAST

Fast-mode, output slew rate is faster. Refer to the appropriate specific device data sheet for details.

End of enumeration elements list.

INVERT : Input polarity.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

0 : DISABLED

Disabled. Input function is not inverted.

0x1 : ENABLED

Enabled. Input is function inverted.

End of enumeration elements list.

DIGIMODE : Select Digital mode.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

0 : ANALOG

Disable digital mode. Digital input set to 0.

0x1 : DIGITAL

Enable Digital mode. Digital input is enabled.

End of enumeration elements list.

OD : Controls open-drain mode.
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

0 : NORMAL

Normal. Normal push-pull output

0x1 : OPEN_DRAIN

Open-drain. Simulated open-drain output (high drive disabled).

End of enumeration elements list.


PIO1_25

Digital I/O control for port 1 pins PIO1_25
address_offset : 0xE4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO1_25 PIO1_25 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE SLEW INVERT DIGIMODE OD

FUNC : Selects pin function.
bits : 0 - 3 (4 bit)
access : read-write

Enumeration:

0 : ALT0

Alternative connection 0.

0x1 : ALT1

Alternative connection 1.

0x2 : ALT2

Alternative connection 2.

0x3 : ALT3

Alternative connection 3.

0x4 : ALT4

Alternative connection 4.

0x5 : ALT5

Alternative connection 5.

0x6 : ALT6

Alternative connection 6.

0x7 : ALT7

Alternative connection 7.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : INACTIVE

Inactive. Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN

Pull-down. Pull-down resistor enabled.

0x2 : PULL_UP

Pull-up. Pull-up resistor enabled.

0x3 : REPEATER

Repeater. Repeater mode.

End of enumeration elements list.

SLEW : Driver slew rate.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

0 : STANDARD

Standard-mode, output slew rate is slower. More outputs can be switched simultaneously.

0x1 : FAST

Fast-mode, output slew rate is faster. Refer to the appropriate specific device data sheet for details.

End of enumeration elements list.

INVERT : Input polarity.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

0 : DISABLED

Disabled. Input function is not inverted.

0x1 : ENABLED

Enabled. Input is function inverted.

End of enumeration elements list.

DIGIMODE : Select Digital mode.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

0 : ANALOG

Disable digital mode. Digital input set to 0.

0x1 : DIGITAL

Enable Digital mode. Digital input is enabled.

End of enumeration elements list.

OD : Controls open-drain mode.
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

0 : NORMAL

Normal. Normal push-pull output

0x1 : OPEN_DRAIN

Open-drain. Simulated open-drain output (high drive disabled).

End of enumeration elements list.


PIO1_26

Digital I/O control for port 1 pins PIO1_26
address_offset : 0xE8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO1_26 PIO1_26 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE SLEW INVERT DIGIMODE OD

FUNC : Selects pin function.
bits : 0 - 3 (4 bit)
access : read-write

Enumeration:

0 : ALT0

Alternative connection 0.

0x1 : ALT1

Alternative connection 1.

0x2 : ALT2

Alternative connection 2.

0x3 : ALT3

Alternative connection 3.

0x4 : ALT4

Alternative connection 4.

0x5 : ALT5

Alternative connection 5.

0x6 : ALT6

Alternative connection 6.

0x7 : ALT7

Alternative connection 7.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : INACTIVE

Inactive. Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN

Pull-down. Pull-down resistor enabled.

0x2 : PULL_UP

Pull-up. Pull-up resistor enabled.

0x3 : REPEATER

Repeater. Repeater mode.

End of enumeration elements list.

SLEW : Driver slew rate.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

0 : STANDARD

Standard-mode, output slew rate is slower. More outputs can be switched simultaneously.

0x1 : FAST

Fast-mode, output slew rate is faster. Refer to the appropriate specific device data sheet for details.

End of enumeration elements list.

INVERT : Input polarity.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

0 : DISABLED

Disabled. Input function is not inverted.

0x1 : ENABLED

Enabled. Input is function inverted.

End of enumeration elements list.

DIGIMODE : Select Digital mode.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

0 : ANALOG

Disable digital mode. Digital input set to 0.

0x1 : DIGITAL

Enable Digital mode. Digital input is enabled.

End of enumeration elements list.

OD : Controls open-drain mode.
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

0 : NORMAL

Normal. Normal push-pull output

0x1 : OPEN_DRAIN

Open-drain. Simulated open-drain output (high drive disabled).

End of enumeration elements list.


PIO1_27

Digital I/O control for port 1 pins PIO1_27
address_offset : 0xEC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO1_27 PIO1_27 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE SLEW INVERT DIGIMODE OD

FUNC : Selects pin function.
bits : 0 - 3 (4 bit)
access : read-write

Enumeration:

0 : ALT0

Alternative connection 0.

0x1 : ALT1

Alternative connection 1.

0x2 : ALT2

Alternative connection 2.

0x3 : ALT3

Alternative connection 3.

0x4 : ALT4

Alternative connection 4.

0x5 : ALT5

Alternative connection 5.

0x6 : ALT6

Alternative connection 6.

0x7 : ALT7

Alternative connection 7.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : INACTIVE

Inactive. Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN

Pull-down. Pull-down resistor enabled.

0x2 : PULL_UP

Pull-up. Pull-up resistor enabled.

0x3 : REPEATER

Repeater. Repeater mode.

End of enumeration elements list.

SLEW : Driver slew rate.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

0 : STANDARD

Standard-mode, output slew rate is slower. More outputs can be switched simultaneously.

0x1 : FAST

Fast-mode, output slew rate is faster. Refer to the appropriate specific device data sheet for details.

End of enumeration elements list.

INVERT : Input polarity.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

0 : DISABLED

Disabled. Input function is not inverted.

0x1 : ENABLED

Enabled. Input is function inverted.

End of enumeration elements list.

DIGIMODE : Select Digital mode.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

0 : ANALOG

Disable digital mode. Digital input set to 0.

0x1 : DIGITAL

Enable Digital mode. Digital input is enabled.

End of enumeration elements list.

OD : Controls open-drain mode.
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

0 : NORMAL

Normal. Normal push-pull output

0x1 : OPEN_DRAIN

Open-drain. Simulated open-drain output (high drive disabled).

End of enumeration elements list.


PIO1_28

Digital I/O control for port 1 pins PIO1_28
address_offset : 0xF0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO1_28 PIO1_28 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE SLEW INVERT DIGIMODE OD

FUNC : Selects pin function.
bits : 0 - 3 (4 bit)
access : read-write

Enumeration:

0 : ALT0

Alternative connection 0.

0x1 : ALT1

Alternative connection 1.

0x2 : ALT2

Alternative connection 2.

0x3 : ALT3

Alternative connection 3.

0x4 : ALT4

Alternative connection 4.

0x5 : ALT5

Alternative connection 5.

0x6 : ALT6

Alternative connection 6.

0x7 : ALT7

Alternative connection 7.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : INACTIVE

Inactive. Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN

Pull-down. Pull-down resistor enabled.

0x2 : PULL_UP

Pull-up. Pull-up resistor enabled.

0x3 : REPEATER

Repeater. Repeater mode.

End of enumeration elements list.

SLEW : Driver slew rate.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

0 : STANDARD

Standard-mode, output slew rate is slower. More outputs can be switched simultaneously.

0x1 : FAST

Fast-mode, output slew rate is faster. Refer to the appropriate specific device data sheet for details.

End of enumeration elements list.

INVERT : Input polarity.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

0 : DISABLED

Disabled. Input function is not inverted.

0x1 : ENABLED

Enabled. Input is function inverted.

End of enumeration elements list.

DIGIMODE : Select Digital mode.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

0 : ANALOG

Disable digital mode. Digital input set to 0.

0x1 : DIGITAL

Enable Digital mode. Digital input is enabled.

End of enumeration elements list.

OD : Controls open-drain mode.
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

0 : NORMAL

Normal. Normal push-pull output

0x1 : OPEN_DRAIN

Open-drain. Simulated open-drain output (high drive disabled).

End of enumeration elements list.


PIO1_29

Digital I/O control for port 1 pins PIO1_29
address_offset : 0xF4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO1_29 PIO1_29 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE SLEW INVERT DIGIMODE OD

FUNC : Selects pin function.
bits : 0 - 3 (4 bit)
access : read-write

Enumeration:

0 : ALT0

Alternative connection 0.

0x1 : ALT1

Alternative connection 1.

0x2 : ALT2

Alternative connection 2.

0x3 : ALT3

Alternative connection 3.

0x4 : ALT4

Alternative connection 4.

0x5 : ALT5

Alternative connection 5.

0x6 : ALT6

Alternative connection 6.

0x7 : ALT7

Alternative connection 7.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : INACTIVE

Inactive. Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN

Pull-down. Pull-down resistor enabled.

0x2 : PULL_UP

Pull-up. Pull-up resistor enabled.

0x3 : REPEATER

Repeater. Repeater mode.

End of enumeration elements list.

SLEW : Driver slew rate.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

0 : STANDARD

Standard-mode, output slew rate is slower. More outputs can be switched simultaneously.

0x1 : FAST

Fast-mode, output slew rate is faster. Refer to the appropriate specific device data sheet for details.

End of enumeration elements list.

INVERT : Input polarity.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

0 : DISABLED

Disabled. Input function is not inverted.

0x1 : ENABLED

Enabled. Input is function inverted.

End of enumeration elements list.

DIGIMODE : Select Digital mode.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

0 : ANALOG

Disable digital mode. Digital input set to 0.

0x1 : DIGITAL

Enable Digital mode. Digital input is enabled.

End of enumeration elements list.

OD : Controls open-drain mode.
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

0 : NORMAL

Normal. Normal push-pull output

0x1 : OPEN_DRAIN

Open-drain. Simulated open-drain output (high drive disabled).

End of enumeration elements list.


PIO1_30

Digital I/O control for port 1 pins PIO1_30
address_offset : 0xF8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO1_30 PIO1_30 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE SLEW INVERT DIGIMODE OD

FUNC : Selects pin function.
bits : 0 - 3 (4 bit)
access : read-write

Enumeration:

0 : ALT0

Alternative connection 0.

0x1 : ALT1

Alternative connection 1.

0x2 : ALT2

Alternative connection 2.

0x3 : ALT3

Alternative connection 3.

0x4 : ALT4

Alternative connection 4.

0x5 : ALT5

Alternative connection 5.

0x6 : ALT6

Alternative connection 6.

0x7 : ALT7

Alternative connection 7.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : INACTIVE

Inactive. Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN

Pull-down. Pull-down resistor enabled.

0x2 : PULL_UP

Pull-up. Pull-up resistor enabled.

0x3 : REPEATER

Repeater. Repeater mode.

End of enumeration elements list.

SLEW : Driver slew rate.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

0 : STANDARD

Standard-mode, output slew rate is slower. More outputs can be switched simultaneously.

0x1 : FAST

Fast-mode, output slew rate is faster. Refer to the appropriate specific device data sheet for details.

End of enumeration elements list.

INVERT : Input polarity.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

0 : DISABLED

Disabled. Input function is not inverted.

0x1 : ENABLED

Enabled. Input is function inverted.

End of enumeration elements list.

DIGIMODE : Select Digital mode.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

0 : ANALOG

Disable digital mode. Digital input set to 0.

0x1 : DIGITAL

Enable Digital mode. Digital input is enabled.

End of enumeration elements list.

OD : Controls open-drain mode.
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

0 : NORMAL

Normal. Normal push-pull output

0x1 : OPEN_DRAIN

Open-drain. Simulated open-drain output (high drive disabled).

End of enumeration elements list.


PIO1_31

Digital I/O control for port 1 pins PIO1_31
address_offset : 0xFC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PIO1_31 PIO1_31 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FUNC MODE SLEW INVERT DIGIMODE OD

FUNC : Selects pin function.
bits : 0 - 3 (4 bit)
access : read-write

Enumeration:

0 : ALT0

Alternative connection 0.

0x1 : ALT1

Alternative connection 1.

0x2 : ALT2

Alternative connection 2.

0x3 : ALT3

Alternative connection 3.

0x4 : ALT4

Alternative connection 4.

0x5 : ALT5

Alternative connection 5.

0x6 : ALT6

Alternative connection 6.

0x7 : ALT7

Alternative connection 7.

End of enumeration elements list.

MODE : Selects function mode (on-chip pull-up/pull-down resistor control).
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : INACTIVE

Inactive. Inactive (no pull-down/pull-up resistor enabled).

0x1 : PULL_DOWN

Pull-down. Pull-down resistor enabled.

0x2 : PULL_UP

Pull-up. Pull-up resistor enabled.

0x3 : REPEATER

Repeater. Repeater mode.

End of enumeration elements list.

SLEW : Driver slew rate.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

0 : STANDARD

Standard-mode, output slew rate is slower. More outputs can be switched simultaneously.

0x1 : FAST

Fast-mode, output slew rate is faster. Refer to the appropriate specific device data sheet for details.

End of enumeration elements list.

INVERT : Input polarity.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

0 : DISABLED

Disabled. Input function is not inverted.

0x1 : ENABLED

Enabled. Input is function inverted.

End of enumeration elements list.

DIGIMODE : Select Digital mode.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

0 : ANALOG

Disable digital mode. Digital input set to 0.

0x1 : DIGITAL

Enable Digital mode. Digital input is enabled.

End of enumeration elements list.

OD : Controls open-drain mode.
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

0 : NORMAL

Normal. Normal push-pull output

0x1 : OPEN_DRAIN

Open-drain. Simulated open-drain output (high drive disabled).

End of enumeration elements list.



Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !

This website is sponsored by EmbeetleEmbeetle, an IDE designed from scratch for embedded software developers.