\n
address_offset : 0x0 Bytes (0x0)
size : 0x2304 byte (0x0)
mem_usage : registers
protection : not protected
Byte pin registers for all port 0 and 1 GPIO pins
address_offset : 0x0 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PBYTE : Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 0 (1 bit)
access : read-write
Byte pin registers for all port 0 and 1 GPIO pins
address_offset : 0x1 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PBYTE : Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 0 (1 bit)
access : read-write
Byte pin registers for all port 0 and 1 GPIO pins
address_offset : 0x10 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PBYTE : Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 0 (1 bit)
access : read-write
Word pin registers for all port 0 and 1 GPIO pins
address_offset : 0x1000 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PWORD : Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 31 (32 bit)
access : read-write
Word pin registers for all port 0 and 1 GPIO pins
address_offset : 0x1004 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PWORD : Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 31 (32 bit)
access : read-write
Word pin registers for all port 0 and 1 GPIO pins
address_offset : 0x1008 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PWORD : Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 31 (32 bit)
access : read-write
Word pin registers for all port 0 and 1 GPIO pins
address_offset : 0x100C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PWORD : Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 31 (32 bit)
access : read-write
Word pin registers for all port 0 and 1 GPIO pins
address_offset : 0x1010 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PWORD : Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 31 (32 bit)
access : read-write
Word pin registers for all port 0 and 1 GPIO pins
address_offset : 0x1014 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PWORD : Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 31 (32 bit)
access : read-write
Word pin registers for all port 0 and 1 GPIO pins
address_offset : 0x1018 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PWORD : Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 31 (32 bit)
access : read-write
Word pin registers for all port 0 and 1 GPIO pins
address_offset : 0x101C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PWORD : Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 31 (32 bit)
access : read-write
Word pin registers for all port 0 and 1 GPIO pins
address_offset : 0x1020 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PWORD : Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 31 (32 bit)
access : read-write
Word pin registers for all port 0 and 1 GPIO pins
address_offset : 0x1024 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PWORD : Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 31 (32 bit)
access : read-write
Word pin registers for all port 0 and 1 GPIO pins
address_offset : 0x1028 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PWORD : Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 31 (32 bit)
access : read-write
Word pin registers for all port 0 and 1 GPIO pins
address_offset : 0x102C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PWORD : Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 31 (32 bit)
access : read-write
Word pin registers for all port 0 and 1 GPIO pins
address_offset : 0x1030 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PWORD : Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 31 (32 bit)
access : read-write
Word pin registers for all port 0 and 1 GPIO pins
address_offset : 0x1034 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PWORD : Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 31 (32 bit)
access : read-write
Word pin registers for all port 0 and 1 GPIO pins
address_offset : 0x1038 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PWORD : Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 31 (32 bit)
access : read-write
Word pin registers for all port 0 and 1 GPIO pins
address_offset : 0x103C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PWORD : Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 31 (32 bit)
access : read-write
Word pin registers for all port 0 and 1 GPIO pins
address_offset : 0x1040 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PWORD : Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 31 (32 bit)
access : read-write
Word pin registers for all port 0 and 1 GPIO pins
address_offset : 0x1044 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PWORD : Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 31 (32 bit)
access : read-write
Byte pin registers for all port 0 and 1 GPIO pins
address_offset : 0x11 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PBYTE : Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 0 (1 bit)
access : read-write
Byte pin registers for all port 0 and 1 GPIO pins
address_offset : 0x2 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PBYTE : Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 0 (1 bit)
access : read-write
Direction registers
address_offset : 0x2000 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DIRP : Selects pin direction for pin PIOm_n (bit 0 = PIOn_0, bit 1 = PIOn_1, etc.). Supported pins depends on the specific device and package. 0 = input. 1 = output.
bits : 0 - 17 (18 bit)
access : read-write
Mask register
address_offset : 0x2080 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MASKP : Controls which bits corresponding to PIOm_n are active in the MPORT register (bit 0 = PIOn_0, bit 1 = PIOn_1, etc.). Supported pins depends on the specific device and package. 0 = Read MPORT: pin state; write MPORT: load output bit. 1 = Read MPORT: 0; write MPORT: output bit not affected.
bits : 0 - 17 (18 bit)
access : read-write
Port pin register
address_offset : 0x2100 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PORT : Reads pin states or loads output bits (bit 0 = PIOn_0, bit 1 = PIOn_1, etc.). Supported pins depends on the specific device and package. 0 = Read: pin is low; write: clear output bit. 1 = Read: pin is high; write: set output bit.
bits : 0 - 17 (18 bit)
access : read-write
Masked port register
address_offset : 0x2180 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MPORTP : Masked port register (bit 0 = PIOn_0, bit 1 = PIOn_1, etc.). Supported pins depends on the specific device and package. 0 = Read: pin is LOW and/or the corresponding bit in the MASK register is 1; write: clear output bit if the corresponding bit in the MASK register is 0. 1 = Read: pin is HIGH and the corresponding bit in the MASK register is 0; write: set output bit if the corresponding bit in the MASK register is 0.
bits : 0 - 17 (18 bit)
access : read-write
Write: Set register for port Read: output bits for port
address_offset : 0x2200 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
SETP : Read or set output bits (bit 0 = PIOn_0, bit 1 = PIOn_1, etc.). Supported pins depends on the specific device and package. 0 = Read: output bit: write: no operation. 1 = Read: output bit; write: set output bit.
bits : 0 - 17 (18 bit)
access : read-write
Clear port
address_offset : 0x2280 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
CLRP : Clear output bits (bit 0 = PIOn_0, bit 1 = PIOn_1, etc.). Supported pins depends on the specific device and package. 0 = No operation. 1 = Clear output bit.
bits : 0 - 17 (18 bit)
access : write-only
Toggle port
address_offset : 0x2300 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
NOTP : Toggle output bits (bit 0 = PIOn_0, bit 1 = PIOn_1, etc.). Supported pins depends on the specific device and package. 0 = no operation. 1 = Toggle output bit.
bits : 0 - 17 (18 bit)
access : write-only
Byte pin registers for all port 0 and 1 GPIO pins
address_offset : 0x3 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PBYTE : Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 0 (1 bit)
access : read-write
Byte pin registers for all port 0 and 1 GPIO pins
address_offset : 0x4 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PBYTE : Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 0 (1 bit)
access : read-write
Byte pin registers for all port 0 and 1 GPIO pins
address_offset : 0x5 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PBYTE : Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 0 (1 bit)
access : read-write
Byte pin registers for all port 0 and 1 GPIO pins
address_offset : 0x6 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PBYTE : Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 0 (1 bit)
access : read-write
Byte pin registers for all port 0 and 1 GPIO pins
address_offset : 0x7 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PBYTE : Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 0 (1 bit)
access : read-write
Byte pin registers for all port 0 and 1 GPIO pins
address_offset : 0x8 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PBYTE : Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 0 (1 bit)
access : read-write
Byte pin registers for all port 0 and 1 GPIO pins
address_offset : 0x9 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PBYTE : Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 0 (1 bit)
access : read-write
Byte pin registers for all port 0 and 1 GPIO pins
address_offset : 0xA Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PBYTE : Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 0 (1 bit)
access : read-write
Byte pin registers for all port 0 and 1 GPIO pins
address_offset : 0xB Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PBYTE : Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 0 (1 bit)
access : read-write
Byte pin registers for all port 0 and 1 GPIO pins
address_offset : 0xC Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PBYTE : Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 0 (1 bit)
access : read-write
Byte pin registers for all port 0 and 1 GPIO pins
address_offset : 0xD Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PBYTE : Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 0 (1 bit)
access : read-write
Byte pin registers for all port 0 and 1 GPIO pins
address_offset : 0xE Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PBYTE : Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 0 (1 bit)
access : read-write
Byte pin registers for all port 0 and 1 GPIO pins
address_offset : 0xF Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PBYTE : Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package.
bits : 0 - 0 (1 bit)
access : read-write
Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !
This website is sponsored by Embeetle, an IDE designed from scratch for embedded software developers.