Embeetle, an IDE designed from scratch for embedded software developers.address_offset : 0x0 Bytes (0x0)
size : 0xC byte (0x0)
mem_usage : registers
protection : not protected
no description available
address_offset : 0x0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
ADP_WAIT : Delay between 2 ADP probe, default value is about 1.5 s in 32 KHz.
bits : 0 - 17 (18 bit)
access : read-write
Enumeration:
0xC000 : ADP_WAIT_49152
Default
End of enumeration elements list.
TIMER_EN : ADP Timer Test Enable
bits : 20 - 20 (1 bit)
access : read-write
Enumeration:
0 : TIMER_EN_0
Default
End of enumeration elements list.
ADP_SNS_INT_EN : ADP Sense Interrupt Enable
bits : 21 - 21 (1 bit)
access : read-write
Enumeration:
0 : ADP_SNS_INT_EN_0
Default
End of enumeration elements list.
ADP_PRB_INT_EN : ADP probe interrupt enable
bits : 22 - 22 (1 bit)
access : read-write
Enumeration:
0 : ADP_PRB_INT_EN_0
Default
End of enumeration elements list.
ADP_PRB_EN : Set to enable the ADP probe sequence
bits : 23 - 23 (1 bit)
access : read-write
Enumeration:
0 : ADP_PRB_EN_0
Default
End of enumeration elements list.
no description available
address_offset : 0x4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
ADP_CHRG_DELTA : ADP charge time compare If diffence is larger than ADP_CHG_DELTA, it generates ADP_PROBE interrupt.
bits : 0 - 6 (7 bit)
access : read-write
Enumeration:
0x10 : ADP_CHRG_DELTA_16
Default
End of enumeration elements list.
ADP_CHRG_SWCMP : If set, HW uses ADP_CHRG_SWTIME to compare
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
0 : ADP_CHRG_SWCMP_0
Default
End of enumeration elements list.
ADP_CHRG_SWTIME : ADP charge time assigned by software
bits : 8 - 15 (8 bit)
access : read-write
Enumeration:
0x40 : ADP_CHRG_SWTIME_64
Default
End of enumeration elements list.
ADP_DISCHG_TIME : ADP Discharge time
bits : 16 - 23 (8 bit)
access : read-write
Enumeration:
0x46 : ADP_DISCHG_TIME_70
Default
End of enumeration elements list.
no description available
address_offset : 0x8 Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
ADP_PRB_TIMR : ADP Probe Time
bits : 0 - 7 (8 bit)
access : read-only
Enumeration:
0 : ADP_PRB_TIMR_0
Default
End of enumeration elements list.
ADP_CNT : ADP Internal 18-bit Counter
bits : 8 - 25 (18 bit)
access : read-only
ADP_SNS_INT : ADP Sense Interrupt Status
bits : 26 - 26 (1 bit)
access : read-only
Enumeration:
0 : ADP_SNS_INT_0
Default
End of enumeration elements list.
ADP_PRB_INT : ADP Probe Interrupt Status
bits : 27 - 27 (1 bit)
access : read-only
Enumeration:
0 : ADP_PRB_INT_0
Default
End of enumeration elements list.
Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !
This website is sponsored by Embeetle, an IDE designed from scratch for embedded software developers.