DSI_HOST_CFG_DPI_PIXEL_PAYLOAD_SIZE

DSI_HOST_CFG_DPI_VSYNC_POLARITY

DSI_HOST_CFG_DPI_HSYNC_POLARITY

DSI_HOST_CFG_DPI_VIDEO_MODE

DSI_HOST_CFG_DPI_HFP

DSI_HOST_CFG_DPI_HBP

DSI_HOST_CFG_DPI_HSA

DSI_HOST_CFG_DPI_ENABLE_MULT_PKTS

DSI_HOST_CFG_DPI_VBP

DSI_HOST_CFG_DPI_VFP

DSI_HOST_CFG_DPI_BLLP_MODE

DSI_HOST_CFG_DPI_USE_NULL_PKT_BLLP

DSI_HOST_CFG_DPI_VACTIVE

DSI_HOST_CFG_DPI_PIXEL_FIFO_SEND_LEVEL

DSI_HOST_CFG_DPI_VC

DSI_HOST_CFG_DPI_INTERFACE_COLOR_CODING

DSI_HOST_CFG_DPI_PIXEL_FORMAT

dsi_host_cfg_dpi_pixel_payload_size : Maximum number of pixels that should be sent as one DSI packet. Recommended that the line size (in pixels) is evenly divisible by this parameter (packet payload size in pixels).
bits : 0 - 15 (16 bit)
access : read-write

dsi_host_cfg_dpi_vsync_polarity : Sets polarity of dpi_vsync_input 0 - active low 1 - active high
bits : 0 - 0 (1 bit)
access : read-write

dsi_host_cfg_dpi_hsync_polarity : Sets polarity of dpi_hsync_input 0 - active low 1 - active high
bits : 0 - 0 (1 bit)
access : read-write

dsi_host_cfg_dpi_video_mode : Select DSI video mode that the host DPI module should generate packets for. 2'b00 - Non-Burst mode with Sync Pulses 2'b01 - Non-Burst mode with Sync Events 2'b10 - Burst mode 2'b11 - Reserved, not valid
bits : 0 - 1 (2 bit)
access : read-write

dsi_host_cfg_dpi_hfp : Sets the DSI packet payload size, in bytes, of the horizontal front porch blanking packet.
bits : 0 - 15 (16 bit)
access : read-write

dsi_host_cfg_dpi_hbp : Sets the DSI packet payload size, in bytes, of the horizontal back porch blanking packet.
bits : 0 - 15 (16 bit)
access : read-write

dsi_host_cfg_dpi_hsa : Sets the DSI packet payload size, in bytes, of the horizontal sync width filler blanking packet.
bits : 0 - 15 (16 bit)
access : read-write

dsi_host_cfg_dpi_enable_mult_pkts : Enable Multiple packets per video line. When enabled, cfg_dpi_pixel_payload_size must be set to exactly half the size of the video line. 0 - Video Line is sent in a single packet 1 - Video Line is sent in two packets
bits : 0 - 0 (1 bit)
access : read-write

dsi_host_cfg_dpi_vbp : Sets the number of lines in the vertical back porch.
bits : 0 - 7 (8 bit)
access : read-write

dsi_host_cfg_dpi_vfp : Sets the number of lines in the vertical front porch.
bits : 0 - 7 (8 bit)
access : read-write

dsi_host_cfg_dpi_bllp_mode : Optimize bllp periods to Low Power mode when possible 0 - blanking packets are sent during BLLP periods 1 - LP mode is used for BLLP periods
bits : 0 - 0 (1 bit)
access : read-write

dsi_host_cfg_dpi_use_null_pkt_bllp : Selects type of blanking packet to be sent during bllp region 0 - Blanking packet used in bllp region 1 - Null packet used in bllp region
bits : 0 - 0 (1 bit)
access : read-write

dsi_host_cfg_dpi_vactive : Sets the number of lines in the vertical active area. This field is equivalent to (real vertical size) - 1. For example, for an image of size 640x480, the bit field should be set as 479.
bits : 0 - 13 (14 bit)
access : read-write

dsi_host_cfg_dpi_pixel_fifo_send_level : In order to optimize DSI utility, the DPI bridge buffers a cerntain number of DPI pixels before initiating a DSI packet. This configuration port controls the level at which the DPI Host bridge begins sending pixels.
bits : 0 - 15 (16 bit)
access : read-write

dsi_host_cfg_dpi_vc : Sets the Virtual Channel (VC) of packets that will be sent to the receive packet interface. Packets with VC not equal to this value are discarded and the "DSI VC ID Invalid" bit (bit 12) in the DSI error report is set.
bits : 0 - 1 (2 bit)
access : read-write

dsi_host_cfg_dpi_interface_color_coding : Sets the distribution of RGB bits within the 24-bit d bus, as specified by the DPI specification. 0= 16-bit Configuration 1 1= 16-bit Configuration 2 2= 16-bit Configuration 3 3= 18-bit Configuration 1 4= 18-bit Configuration 2 5= 24-bit
bits : 0 - 2 (3 bit)
access : read-write

dsi_host_cfg_dpi_pixel_format : Sets the DSI packet type of the pixels. 0 - 16 bit 1 - 18 bit 2 - 18 bit loosely packed 3 - 24 bit
bits : 0 - 1 (2 bit)
access : read-write