\n
address_offset : 0x0 Bytes (0x0)
size : 0x48 byte (0x0)
mem_usage : registers
protection : not protected
PMC 1 Version register
address_offset : 0x0 Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
FEATURE : Feature Specification Number
bits : 0 - 15 (16 bit)
access : read-only
Enumeration:
0 : FEATURE_0
Standard features implemented
End of enumeration elements list.
MINOR : Minor Version Number
bits : 16 - 23 (8 bit)
access : read-only
MAJOR : Major Version Number
bits : 24 - 31 (8 bit)
access : read-only
PMC 1 STOP mode register
address_offset : 0x10 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
LDOVL : LDO Regulator Voltage Level
bits : 16 - 21 (6 bit)
access : read-write
Enumeration:
0 : LDOVL_0
LDO Voltage Level is 0.60V
0x1 : LDOVL_1
LDO Voltage Level is 0.61V
0x31 : LDOVL_49
LDO Voltage Level is 1.09V
0x32 : LDOVL_50
LDO Voltage Level is 1.10V
End of enumeration elements list.
PMC 1 VLPS mode register
address_offset : 0x14 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
LDOM : LDO Regulator Mode
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
0 : LDOM_0
Linear LDO LP Regulator is enabled.
0x1 : LDOM_1
Linear LDO HP Regulator is enabled.
End of enumeration elements list.
MONLVD : Low-Voltage Detector
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
0 : MONLVD_0
LP monitor is enabled.
0x1 : MONLVD_1
HP monitor is enabled.
End of enumeration elements list.
MONHVD : 1.2V HP High-Voltage Detector
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
0 : MONHVD_0
The monitor is disabled.
0x1 : MONHVD_1
The monitor is enabled.
End of enumeration elements list.
LDOVL : LDO Regulator Voltage Level
bits : 16 - 21 (6 bit)
access : read-write
Enumeration:
0 : LDOVL_0
LDO Voltage Level is 0.60V
0x1 : LDOVL_1
LDO Voltage Level is 0.61V
0x31 : LDOVL_49
LDO Voltage Level is 1.09V
0x32 : LDOVL_50
LDO Voltage Level is 1.10V
End of enumeration elements list.
RBBEN : Reverse Back Bias Enable
bits : 28 - 28 (1 bit)
access : read-write
Enumeration:
0 : RBBEN_0
RBB is disabled
0x1 : RBBEN_1
RBB is enabled
End of enumeration elements list.
PMC 1 LLS mode register
address_offset : 0x18 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
LDOM : LDO Regulator Mode
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
0 : LDOM_0
Linear LDO LP Regulator is enabled.
0x1 : LDOM_1
Linear LDO HP Regulator is enabled.
End of enumeration elements list.
MONLVD : Low-Voltage Detector
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
0 : MONLVD_0
LP monitor is enabled.
0x1 : MONLVD_1
HP monitor is enabled.
End of enumeration elements list.
MONHVD : 1.2V HP High-Voltage Detector
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
0 : MONHVD_0
The monitor is disabled.
0x1 : MONHVD_1
The monitor is enabled.
End of enumeration elements list.
LDOVL : Linear LDO Regulator Voltage Level
bits : 16 - 21 (6 bit)
access : read-write
Enumeration:
0 : LDOVL_0
LDO Voltage Level is 0.60V
0x1 : LDOVL_1
LDO Voltage Level is 0.61V
0x31 : LDOVL_49
LDO Voltage Level is 1.09V
0x32 : LDOVL_50
LDO Voltage Level is 1.10V
End of enumeration elements list.
RBBEN : Reverse Back Bias Enable
bits : 28 - 28 (1 bit)
access : read-write
Enumeration:
0 : RBBEN_0
RBB is disabled
0x1 : RBBEN_1
RBB is enabled
End of enumeration elements list.
PMC 1 VLLS mode register
address_offset : 0x1C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
LDOM : LDO Regulator Mode
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
0 : LDOM_0
Linear LDO LP Regulator is enabled.
0x1 : LDOM_1
Linear LDO HP Regulator is enabled.
End of enumeration elements list.
MONLVD : Low-Voltage Detector
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
0 : MONLVD_0
LP monitor is enabled.
0x1 : MONLVD_1
HP monitor is enabled.
End of enumeration elements list.
MONHVD : 1.2V HP High-Voltage Detector
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
0 : MONHVD_0
The monitor is disabled.
0x1 : MONHVD_1
The monitor is enabled.
End of enumeration elements list.
PMC 1 Status register
address_offset : 0x20 Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
LVDF : 1.2V Low-Voltage Detector Flag
bits : 0 - 0 (1 bit)
access : read-only
Enumeration:
0 : LVDF_0
Low-voltage event was not detected by the 1.2V LVD monitor in the PMC 1
0x1 : LVDF_1
Low-voltage event was detected by the 1.2V LVD monitor in the PMC 1
End of enumeration elements list.
LVDV : 1.2V Low-Voltage Detector Value
bits : 1 - 1 (1 bit)
access : read-only
Enumeration:
0 : LVDV_0
Low-voltage event was not detected by the 1.2V LVD monitor in the PMC 1
0x1 : LVDV_1
Low-voltage event was detected by the 1.2V LVD monitor in the PMC 1
End of enumeration elements list.
HVDF : 1.2V High-Voltage Detector Flag
bits : 4 - 4 (1 bit)
access : read-only
Enumeration:
0 : HVDF_0
High-voltage event was not detected by the 1.2V HVD monitor in PMC 1
0x1 : HVDF_1
High-voltage event was detected by the 1.2V HVD monitor in PMC 1
End of enumeration elements list.
HVDV : 1.2V High-Voltage Detector Value
bits : 5 - 5 (1 bit)
access : read-only
Enumeration:
0 : HVDV_0
High-voltage event was not detected by the 1.2V HVD monitor in PMC 1
0x1 : HVDV_1
High-voltage event was detected by the 1.2V HVD monitor in PMC 1
End of enumeration elements list.
LDOVLF : LDO Voltage Level Flag
bits : 8 - 8 (1 bit)
access : read-only
Enumeration:
0 : LDOVLF_0
LDO Voltage Level is stable
0x1 : LDOVLF_1
LDO Voltage Level is changing
End of enumeration elements list.
SRAMF : SRAM Flag
bits : 24 - 24 (1 bit)
access : read-only
Enumeration:
0 : SRAMF_0
No change request in the SRAMs.
0x1 : SRAMF_1
A change mode request is being processed in the SRAMs.
End of enumeration elements list.
PMC 1 Control register
address_offset : 0x24 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
LVDIE : Low-Voltage Detector Interrupt Enable
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
0 : LVDIE_0
Low-voltage detector interrupt is disabled
0x1 : LVDIE_1
Low-voltage detector interrupt is enabled
End of enumeration elements list.
LVDACK : 1.2V Low-Voltage Detector Acknowledge
bits : 1 - 1 (1 bit)
access : write-only
HVDIE : 1.2V High-Voltage Detector Interrupt Enable
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
0 : HVDIE_0
1.2V high-voltage detector interrupt is disabled
0x1 : HVDIE_1
1.2V high-voltage detector interrupt is enabled
End of enumeration elements list.
HVDACK : 1.2V High-Voltage Detector Acknowledge
bits : 3 - 3 (1 bit)
access : write-only
LVDRE : Low-Voltage Detector Reset Enable
bits : 8 - 8 (1 bit)
access : read-write
Enumeration:
0 : LVDRE_0
Low-voltage detector reset is disabled
0x1 : LVDRE_1
Low-voltage detector reset is enabled
End of enumeration elements list.
HVDRE : 1.2V High-Voltage Detector Reset Enable
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
0 : HVDRE_0
1.2V high-voltage detector reset is disabled
0x1 : HVDRE_1
1.2V high-voltage detector reset is enabled
End of enumeration elements list.
ISOACK : Isolation Acknowledge
bits : 14 - 14 (1 bit)
access : write-only
PMC 1 Biasing Control register
address_offset : 0x34 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RBBNLEVEL : RBB N-Well Voltage Level
bits : 0 - 3 (4 bit)
access : read-write
Enumeration:
0 : RBBNLEVEL_0
Voltage level at 0.5V.
0x1 : RBBNLEVEL_1
Voltage level at 0.6V.
0x2 : RBBNLEVEL_2
Voltage level at 0.7V.
0x3 : RBBNLEVEL_3
Voltage level at 0.8V.
0x4 : RBBNLEVEL_4
Voltage level at 0.9V.
0x5 : RBBNLEVEL_5
Voltage level at 1.0V.
0x6 : RBBNLEVEL_6
Voltage level at 1.1V.
0x7 : RBBNLEVEL_7
Voltage level at 1.2V.
0x8 : RBBNLEVEL_8
Voltage level at 1.3V.
End of enumeration elements list.
RBBPLEVEL : RBB P-Well Voltage Level
bits : 8 - 11 (4 bit)
access : read-write
Enumeration:
0 : RBBPLEVEL_0
Voltage level at -0.5V.
0x1 : RBBPLEVEL_1
Voltage level at -0.6V.
0x2 : RBBPLEVEL_2
Voltage level at -0.7V.
0x3 : RBBPLEVEL_3
Voltage level at -0.8V.
0x4 : RBBPLEVEL_4
Voltage level at -0.9V.
0x5 : RBBPLEVEL_5
Voltage level at -1.0V.
0x6 : RBBPLEVEL_6
Voltage level at -1.1V.
0x7 : RBBPLEVEL_7
Voltage level at -1.2V.
0x8 : RBBPLEVEL_8
Voltage level at -1.3V.
End of enumeration elements list.
FBBNLEVEL : FBB N-Well Voltage Level
bits : 16 - 19 (4 bit)
access : read-write
Enumeration:
0 : FBBNLEVEL_0
No BIAS condition.
0x1 : FBBNLEVEL_1
Voltage level at -50mV.
0x2 : FBBNLEVEL_2
Voltage level at -150mV.
0x3 : FBBNLEVEL_3
Voltage level at -100mV.
0x4 : FBBNLEVEL_4
Voltage level at -350mV.
0x5 : FBBNLEVEL_5
Voltage level at -300mV.
0x6 : FBBNLEVEL_6
Voltage level at -200mV.
0x7 : FBBNLEVEL_7
Voltage level at -250mV.
End of enumeration elements list.
FBBPLEVEL : FBB P-Well Voltage Level
bits : 24 - 27 (4 bit)
access : read-write
Enumeration:
0 : FBBPLEVEL_0
No BIAS condition.
0x1 : FBBPLEVEL_1
Voltage level at 50mV.
0x2 : FBBPLEVEL_2
Voltage level at 150mV.
0x3 : FBBPLEVEL_3
Voltage level at 100mV.
0x4 : FBBPLEVEL_4
Voltage level at 350mV.
0x5 : FBBPLEVEL_5
Voltage level at 300mV.
0x6 : FBBPLEVEL_6
Voltage level at 200mV.
0x7 : FBBPLEVEL_7
Voltage level at 250mV.
End of enumeration elements list.
PMC 1 HSRUN mode register
address_offset : 0x4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
LDOVL : LDO Regulator Voltage Level
bits : 16 - 21 (6 bit)
access : read-write
Enumeration:
0 : LDOVL_0
LDO Voltage Level is 0.60V
0x1 : LDOVL_1
LDO Voltage Level is 0.61V
0x31 : LDOVL_49
LDO Voltage Level is 1.09V
0x32 : LDOVL_50
LDO Voltage Level is 1.10V
End of enumeration elements list.
FBBEN : Forward Back Bias Enable
bits : 24 - 24 (1 bit)
access : read-write
Enumeration:
0 : FBBEN_0
FBB is disabled
0x1 : FBBEN_1
FBB is enabled
End of enumeration elements list.
PMC 1 SRAMs Control register
address_offset : 0x44 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
SRAM_STDY : PMC 1 SRAM Bank in Standby Mode
bits : 0 - 7 (8 bit)
access : read-write
PMC 1 RUN mode register
address_offset : 0x8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
LDOVL : LDO Regulator Voltage Level
bits : 16 - 21 (6 bit)
access : read-write
Enumeration:
0 : LDOVL_0
LDO Voltage Level is 0.60V
0x1 : LDOVL_1
LDO Voltage Level is 0.61V
0x31 : LDOVL_49
LDO Voltage Level is 1.09V
0x32 : LDOVL_50
LDO Voltage Level is 1.10V
End of enumeration elements list.
PMC 1 VLPR mode register
address_offset : 0xC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
LDOM : LDO Regulator Mode
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
0 : LDOM_0
Linear LDO LP Regulator is enabled.
0x1 : LDOM_1
Linear LDO HP Regulator is enabled.
End of enumeration elements list.
MONLVD : Low-Voltage Detector
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
0 : MONLVD_0
LP monitor is enabled.
0x1 : MONLVD_1
HP monitor is enabled.
End of enumeration elements list.
MONHVD : 1.2V HP High-Voltage Detector
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
0 : MONHVD_0
The monitor is disabled.
0x1 : MONHVD_1
The monitor is enabled.
End of enumeration elements list.
LDOVL : LDO Regulator Voltage Level
bits : 16 - 21 (6 bit)
access : read-write
Enumeration:
0 : LDOVL_0
LDO Voltage Level is 0.60V
0x1 : LDOVL_1
LDO Voltage Level is 0.61V
0x31 : LDOVL_49
LDO Voltage Level is 1.09V
0x32 : LDOVL_50
LDO Voltage Level is 1.10V
End of enumeration elements list.
Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !
This website is sponsored by Embeetle, an IDE designed from scratch for embedded software developers.