\n
address_offset : 0x0 Bytes (0x0)
size : 0x10 byte (0x0)
mem_usage : registers
protection : not protected
Crossbar B Select Register 0
address_offset : 0x0 Bytes (0x0)
size : 16 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
SEL0 : Input (XBARB_INn) to be muxed to XBARB_OUT0 (refer to Functional Description section for input/output assignment)
bits : 0 - 5 (6 bit)
access : read-write
SEL1 : Input (XBARB_INn) to be muxed to XBARB_OUT1 (refer to Functional Description section for input/output assignment)
bits : 8 - 13 (6 bit)
access : read-write
Crossbar B Select Register 1
address_offset : 0x2 Bytes (0x0)
size : 16 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
SEL2 : Input (XBARB_INn) to be muxed to XBARB_OUT2 (refer to Functional Description section for input/output assignment)
bits : 0 - 5 (6 bit)
access : read-write
SEL3 : Input (XBARB_INn) to be muxed to XBARB_OUT3 (refer to Functional Description section for input/output assignment)
bits : 8 - 13 (6 bit)
access : read-write
Crossbar B Select Register 2
address_offset : 0x4 Bytes (0x0)
size : 16 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
SEL4 : Input (XBARB_INn) to be muxed to XBARB_OUT4 (refer to Functional Description section for input/output assignment)
bits : 0 - 5 (6 bit)
access : read-write
SEL5 : Input (XBARB_INn) to be muxed to XBARB_OUT5 (refer to Functional Description section for input/output assignment)
bits : 8 - 13 (6 bit)
access : read-write
Crossbar B Select Register 3
address_offset : 0x6 Bytes (0x0)
size : 16 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
SEL6 : Input (XBARB_INn) to be muxed to XBARB_OUT6 (refer to Functional Description section for input/output assignment)
bits : 0 - 5 (6 bit)
access : read-write
SEL7 : Input (XBARB_INn) to be muxed to XBARB_OUT7 (refer to Functional Description section for input/output assignment)
bits : 8 - 13 (6 bit)
access : read-write
Crossbar B Select Register 4
address_offset : 0x8 Bytes (0x0)
size : 16 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
SEL8 : Input (XBARB_INn) to be muxed to XBARB_OUT8 (refer to Functional Description section for input/output assignment)
bits : 0 - 5 (6 bit)
access : read-write
SEL9 : Input (XBARB_INn) to be muxed to XBARB_OUT9 (refer to Functional Description section for input/output assignment)
bits : 8 - 13 (6 bit)
access : read-write
Crossbar B Select Register 5
address_offset : 0xA Bytes (0x0)
size : 16 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
SEL10 : Input (XBARB_INn) to be muxed to XBARB_OUT10 (refer to Functional Description section for input/output assignment)
bits : 0 - 5 (6 bit)
access : read-write
SEL11 : Input (XBARB_INn) to be muxed to XBARB_OUT11 (refer to Functional Description section for input/output assignment)
bits : 8 - 13 (6 bit)
access : read-write
Crossbar B Select Register 6
address_offset : 0xC Bytes (0x0)
size : 16 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
SEL12 : Input (XBARB_INn) to be muxed to XBARB_OUT12 (refer to Functional Description section for input/output assignment)
bits : 0 - 5 (6 bit)
access : read-write
SEL13 : Input (XBARB_INn) to be muxed to XBARB_OUT13 (refer to Functional Description section for input/output assignment)
bits : 8 - 13 (6 bit)
access : read-write
Crossbar B Select Register 7
address_offset : 0xE Bytes (0x0)
size : 16 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
SEL14 : Input (XBARB_INn) to be muxed to XBARB_OUT14 (refer to Functional Description section for input/output assignment)
bits : 0 - 5 (6 bit)
access : read-write
SEL15 : Input (XBARB_INn) to be muxed to XBARB_OUT15 (refer to Functional Description section for input/output assignment)
bits : 8 - 13 (6 bit)
access : read-write
Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !
This website is sponsored by Embeetle, an IDE designed from scratch for embedded software developers.