\n
address_offset : 0x0 Bytes (0x0)
size : 0x400 byte (0x0)
mem_usage : registers
protection : not protected
Software Pulse Register
address_offset : 0x0 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
CH0PULSE : Channel 0 Pulse Generation
bits : 0 - 0 (1 bit)
access : write-only
CH1PULSE : Channel 1 Pulse Generation
bits : 1 - 1 (1 bit)
access : write-only
CH2PULSE : Channel 2 Pulse Generation
bits : 2 - 2 (1 bit)
access : write-only
CH3PULSE : Channel 3 Pulse Generation
bits : 3 - 3 (1 bit)
access : write-only
CH4PULSE : Channel 4 Pulse Generation
bits : 4 - 4 (1 bit)
access : write-only
CH5PULSE : Channel 5 Pulse Generation
bits : 5 - 5 (1 bit)
access : write-only
CH6PULSE : Channel 6 Pulse Generation
bits : 6 - 6 (1 bit)
access : write-only
CH7PULSE : Channel 7 Pulse Generation
bits : 7 - 7 (1 bit)
access : write-only
CH8PULSE : Channel 8 Pulse Generation
bits : 8 - 8 (1 bit)
access : write-only
CH9PULSE : Channel 9 Pulse Generation
bits : 9 - 9 (1 bit)
access : write-only
CH10PULSE : Channel 10 Pulse Generation
bits : 10 - 10 (1 bit)
access : write-only
CH11PULSE : Channel 11 Pulse Generation
bits : 11 - 11 (1 bit)
access : write-only
Channel Control Register
address_offset : 0x10 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
SIGSEL : Signal Select
bits : 0 - 2 (3 bit)
access : read-write
SOURCESEL : Source Select
bits : 16 - 21 (6 bit)
access : read-write
Enumeration:
0x00000000 : NONE
No source selected
0x00000001 : VCMP
Voltage Comparator
0x00000002 : ACMP0
Analog Comparator 0
0x00000003 : ACMP1
Analog Comparator 1
0x00000006 : DAC0
Digital to Analog Converter 0
0x00000008 : ADC0
Analog to Digital Converter 0
0x00000010 : USART0
Universal Synchronous/Asynchronous Receiver/Transmitter 0
0x00000011 : USART1
Universal Synchronous/Asynchronous Receiver/Transmitter 1
0x00000012 : USART2
Universal Synchronous/Asynchronous Receiver/Transmitter 2
0x0000001C : TIMER0
Timer 0
0x0000001D : TIMER1
Timer 1
0x0000001E : TIMER2
Timer 2
0x0000001F : TIMER3
Timer 3
0x00000028 : RTC
Real-Time Counter
0x00000029 : UART0
Universal Asynchronous Receiver/Transmitter 0
0x0000002A : UART1
Universal Asynchronous Receiver/Transmitter 1
0x00000030 : GPIOL
General purpose Input/Output
0x00000031 : GPIOH
General purpose Input/Output
0x00000034 : LETIMER0
Low Energy Timer 0
0x00000037 : BURTC
Backup RTC
0x00000039 : LESENSEL
Low Energy Sensor Interface
0x0000003A : LESENSEH
Low Energy Sensor Interface
0x0000003B : LESENSED
Low Energy Sensor Interface
End of enumeration elements list.
EDSEL : Edge Detect Select
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
0x00000000 : OFF
Signal is left as it is
0x00000001 : POSEDGE
A one HFPERCLK cycle pulse is generated for every positive edge of the incoming signal
0x00000002 : NEGEDGE
A one HFPERCLK clock cycle pulse is generated for every negative edge of the incoming signal
0x00000003 : BOTHEDGES
A one HFPERCLK clock cycle pulse is generated for every edge of the incoming signal
End of enumeration elements list.
ASYNC : Asynchronous reflex
bits : 28 - 28 (1 bit)
access : read-write
Channel Control Register
address_offset : 0x14 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
SIGSEL : Signal Select
bits : 0 - 2 (3 bit)
access : read-write
SOURCESEL : Source Select
bits : 16 - 21 (6 bit)
access : read-write
Enumeration:
0x00000000 : NONE
No source selected
0x00000001 : VCMP
Voltage Comparator
0x00000002 : ACMP0
Analog Comparator 0
0x00000003 : ACMP1
Analog Comparator 1
0x00000006 : DAC0
Digital to Analog Converter 0
0x00000008 : ADC0
Analog to Digital Converter 0
0x00000010 : USART0
Universal Synchronous/Asynchronous Receiver/Transmitter 0
0x00000011 : USART1
Universal Synchronous/Asynchronous Receiver/Transmitter 1
0x00000012 : USART2
Universal Synchronous/Asynchronous Receiver/Transmitter 2
0x0000001C : TIMER0
Timer 0
0x0000001D : TIMER1
Timer 1
0x0000001E : TIMER2
Timer 2
0x0000001F : TIMER3
Timer 3
0x00000028 : RTC
Real-Time Counter
0x00000029 : UART0
Universal Asynchronous Receiver/Transmitter 0
0x0000002A : UART1
Universal Asynchronous Receiver/Transmitter 1
0x00000030 : GPIOL
General purpose Input/Output
0x00000031 : GPIOH
General purpose Input/Output
0x00000034 : LETIMER0
Low Energy Timer 0
0x00000037 : BURTC
Backup RTC
0x00000039 : LESENSEL
Low Energy Sensor Interface
0x0000003A : LESENSEH
Low Energy Sensor Interface
0x0000003B : LESENSED
Low Energy Sensor Interface
End of enumeration elements list.
EDSEL : Edge Detect Select
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
0x00000000 : OFF
Signal is left as it is
0x00000001 : POSEDGE
A one HFPERCLK cycle pulse is generated for every positive edge of the incoming signal
0x00000002 : NEGEDGE
A one HFPERCLK clock cycle pulse is generated for every negative edge of the incoming signal
0x00000003 : BOTHEDGES
A one HFPERCLK clock cycle pulse is generated for every edge of the incoming signal
End of enumeration elements list.
ASYNC : Asynchronous reflex
bits : 28 - 28 (1 bit)
access : read-write
Channel Control Register
address_offset : 0x18 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
SIGSEL : Signal Select
bits : 0 - 2 (3 bit)
access : read-write
SOURCESEL : Source Select
bits : 16 - 21 (6 bit)
access : read-write
Enumeration:
0x00000000 : NONE
No source selected
0x00000001 : VCMP
Voltage Comparator
0x00000002 : ACMP0
Analog Comparator 0
0x00000003 : ACMP1
Analog Comparator 1
0x00000006 : DAC0
Digital to Analog Converter 0
0x00000008 : ADC0
Analog to Digital Converter 0
0x00000010 : USART0
Universal Synchronous/Asynchronous Receiver/Transmitter 0
0x00000011 : USART1
Universal Synchronous/Asynchronous Receiver/Transmitter 1
0x00000012 : USART2
Universal Synchronous/Asynchronous Receiver/Transmitter 2
0x0000001C : TIMER0
Timer 0
0x0000001D : TIMER1
Timer 1
0x0000001E : TIMER2
Timer 2
0x0000001F : TIMER3
Timer 3
0x00000028 : RTC
Real-Time Counter
0x00000029 : UART0
Universal Asynchronous Receiver/Transmitter 0
0x0000002A : UART1
Universal Asynchronous Receiver/Transmitter 1
0x00000030 : GPIOL
General purpose Input/Output
0x00000031 : GPIOH
General purpose Input/Output
0x00000034 : LETIMER0
Low Energy Timer 0
0x00000037 : BURTC
Backup RTC
0x00000039 : LESENSEL
Low Energy Sensor Interface
0x0000003A : LESENSEH
Low Energy Sensor Interface
0x0000003B : LESENSED
Low Energy Sensor Interface
End of enumeration elements list.
EDSEL : Edge Detect Select
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
0x00000000 : OFF
Signal is left as it is
0x00000001 : POSEDGE
A one HFPERCLK cycle pulse is generated for every positive edge of the incoming signal
0x00000002 : NEGEDGE
A one HFPERCLK clock cycle pulse is generated for every negative edge of the incoming signal
0x00000003 : BOTHEDGES
A one HFPERCLK clock cycle pulse is generated for every edge of the incoming signal
End of enumeration elements list.
ASYNC : Asynchronous reflex
bits : 28 - 28 (1 bit)
access : read-write
Channel Control Register
address_offset : 0x1C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
SIGSEL : Signal Select
bits : 0 - 2 (3 bit)
access : read-write
SOURCESEL : Source Select
bits : 16 - 21 (6 bit)
access : read-write
Enumeration:
0x00000000 : NONE
No source selected
0x00000001 : VCMP
Voltage Comparator
0x00000002 : ACMP0
Analog Comparator 0
0x00000003 : ACMP1
Analog Comparator 1
0x00000006 : DAC0
Digital to Analog Converter 0
0x00000008 : ADC0
Analog to Digital Converter 0
0x00000010 : USART0
Universal Synchronous/Asynchronous Receiver/Transmitter 0
0x00000011 : USART1
Universal Synchronous/Asynchronous Receiver/Transmitter 1
0x00000012 : USART2
Universal Synchronous/Asynchronous Receiver/Transmitter 2
0x0000001C : TIMER0
Timer 0
0x0000001D : TIMER1
Timer 1
0x0000001E : TIMER2
Timer 2
0x0000001F : TIMER3
Timer 3
0x00000028 : RTC
Real-Time Counter
0x00000029 : UART0
Universal Asynchronous Receiver/Transmitter 0
0x0000002A : UART1
Universal Asynchronous Receiver/Transmitter 1
0x00000030 : GPIOL
General purpose Input/Output
0x00000031 : GPIOH
General purpose Input/Output
0x00000034 : LETIMER0
Low Energy Timer 0
0x00000037 : BURTC
Backup RTC
0x00000039 : LESENSEL
Low Energy Sensor Interface
0x0000003A : LESENSEH
Low Energy Sensor Interface
0x0000003B : LESENSED
Low Energy Sensor Interface
End of enumeration elements list.
EDSEL : Edge Detect Select
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
0x00000000 : OFF
Signal is left as it is
0x00000001 : POSEDGE
A one HFPERCLK cycle pulse is generated for every positive edge of the incoming signal
0x00000002 : NEGEDGE
A one HFPERCLK clock cycle pulse is generated for every negative edge of the incoming signal
0x00000003 : BOTHEDGES
A one HFPERCLK clock cycle pulse is generated for every edge of the incoming signal
End of enumeration elements list.
ASYNC : Asynchronous reflex
bits : 28 - 28 (1 bit)
access : read-write
Channel Control Register
address_offset : 0x20 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
SIGSEL : Signal Select
bits : 0 - 2 (3 bit)
access : read-write
SOURCESEL : Source Select
bits : 16 - 21 (6 bit)
access : read-write
Enumeration:
0x00000000 : NONE
No source selected
0x00000001 : VCMP
Voltage Comparator
0x00000002 : ACMP0
Analog Comparator 0
0x00000003 : ACMP1
Analog Comparator 1
0x00000006 : DAC0
Digital to Analog Converter 0
0x00000008 : ADC0
Analog to Digital Converter 0
0x00000010 : USART0
Universal Synchronous/Asynchronous Receiver/Transmitter 0
0x00000011 : USART1
Universal Synchronous/Asynchronous Receiver/Transmitter 1
0x00000012 : USART2
Universal Synchronous/Asynchronous Receiver/Transmitter 2
0x0000001C : TIMER0
Timer 0
0x0000001D : TIMER1
Timer 1
0x0000001E : TIMER2
Timer 2
0x0000001F : TIMER3
Timer 3
0x00000028 : RTC
Real-Time Counter
0x00000029 : UART0
Universal Asynchronous Receiver/Transmitter 0
0x0000002A : UART1
Universal Asynchronous Receiver/Transmitter 1
0x00000030 : GPIOL
General purpose Input/Output
0x00000031 : GPIOH
General purpose Input/Output
0x00000034 : LETIMER0
Low Energy Timer 0
0x00000037 : BURTC
Backup RTC
0x00000039 : LESENSEL
Low Energy Sensor Interface
0x0000003A : LESENSEH
Low Energy Sensor Interface
0x0000003B : LESENSED
Low Energy Sensor Interface
End of enumeration elements list.
EDSEL : Edge Detect Select
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
0x00000000 : OFF
Signal is left as it is
0x00000001 : POSEDGE
A one HFPERCLK cycle pulse is generated for every positive edge of the incoming signal
0x00000002 : NEGEDGE
A one HFPERCLK clock cycle pulse is generated for every negative edge of the incoming signal
0x00000003 : BOTHEDGES
A one HFPERCLK clock cycle pulse is generated for every edge of the incoming signal
End of enumeration elements list.
ASYNC : Asynchronous reflex
bits : 28 - 28 (1 bit)
access : read-write
Channel Control Register
address_offset : 0x24 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
SIGSEL : Signal Select
bits : 0 - 2 (3 bit)
access : read-write
SOURCESEL : Source Select
bits : 16 - 21 (6 bit)
access : read-write
Enumeration:
0x00000000 : NONE
No source selected
0x00000001 : VCMP
Voltage Comparator
0x00000002 : ACMP0
Analog Comparator 0
0x00000003 : ACMP1
Analog Comparator 1
0x00000006 : DAC0
Digital to Analog Converter 0
0x00000008 : ADC0
Analog to Digital Converter 0
0x00000010 : USART0
Universal Synchronous/Asynchronous Receiver/Transmitter 0
0x00000011 : USART1
Universal Synchronous/Asynchronous Receiver/Transmitter 1
0x00000012 : USART2
Universal Synchronous/Asynchronous Receiver/Transmitter 2
0x0000001C : TIMER0
Timer 0
0x0000001D : TIMER1
Timer 1
0x0000001E : TIMER2
Timer 2
0x0000001F : TIMER3
Timer 3
0x00000028 : RTC
Real-Time Counter
0x00000029 : UART0
Universal Asynchronous Receiver/Transmitter 0
0x0000002A : UART1
Universal Asynchronous Receiver/Transmitter 1
0x00000030 : GPIOL
General purpose Input/Output
0x00000031 : GPIOH
General purpose Input/Output
0x00000034 : LETIMER0
Low Energy Timer 0
0x00000037 : BURTC
Backup RTC
0x00000039 : LESENSEL
Low Energy Sensor Interface
0x0000003A : LESENSEH
Low Energy Sensor Interface
0x0000003B : LESENSED
Low Energy Sensor Interface
End of enumeration elements list.
EDSEL : Edge Detect Select
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
0x00000000 : OFF
Signal is left as it is
0x00000001 : POSEDGE
A one HFPERCLK cycle pulse is generated for every positive edge of the incoming signal
0x00000002 : NEGEDGE
A one HFPERCLK clock cycle pulse is generated for every negative edge of the incoming signal
0x00000003 : BOTHEDGES
A one HFPERCLK clock cycle pulse is generated for every edge of the incoming signal
End of enumeration elements list.
ASYNC : Asynchronous reflex
bits : 28 - 28 (1 bit)
access : read-write
Channel Control Register
address_offset : 0x28 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
SIGSEL : Signal Select
bits : 0 - 2 (3 bit)
access : read-write
SOURCESEL : Source Select
bits : 16 - 21 (6 bit)
access : read-write
Enumeration:
0x00000000 : NONE
No source selected
0x00000001 : VCMP
Voltage Comparator
0x00000002 : ACMP0
Analog Comparator 0
0x00000003 : ACMP1
Analog Comparator 1
0x00000006 : DAC0
Digital to Analog Converter 0
0x00000008 : ADC0
Analog to Digital Converter 0
0x00000010 : USART0
Universal Synchronous/Asynchronous Receiver/Transmitter 0
0x00000011 : USART1
Universal Synchronous/Asynchronous Receiver/Transmitter 1
0x00000012 : USART2
Universal Synchronous/Asynchronous Receiver/Transmitter 2
0x0000001C : TIMER0
Timer 0
0x0000001D : TIMER1
Timer 1
0x0000001E : TIMER2
Timer 2
0x0000001F : TIMER3
Timer 3
0x00000028 : RTC
Real-Time Counter
0x00000029 : UART0
Universal Asynchronous Receiver/Transmitter 0
0x0000002A : UART1
Universal Asynchronous Receiver/Transmitter 1
0x00000030 : GPIOL
General purpose Input/Output
0x00000031 : GPIOH
General purpose Input/Output
0x00000034 : LETIMER0
Low Energy Timer 0
0x00000037 : BURTC
Backup RTC
0x00000039 : LESENSEL
Low Energy Sensor Interface
0x0000003A : LESENSEH
Low Energy Sensor Interface
0x0000003B : LESENSED
Low Energy Sensor Interface
End of enumeration elements list.
EDSEL : Edge Detect Select
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
0x00000000 : OFF
Signal is left as it is
0x00000001 : POSEDGE
A one HFPERCLK cycle pulse is generated for every positive edge of the incoming signal
0x00000002 : NEGEDGE
A one HFPERCLK clock cycle pulse is generated for every negative edge of the incoming signal
0x00000003 : BOTHEDGES
A one HFPERCLK clock cycle pulse is generated for every edge of the incoming signal
End of enumeration elements list.
ASYNC : Asynchronous reflex
bits : 28 - 28 (1 bit)
access : read-write
Channel Control Register
address_offset : 0x2C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
SIGSEL : Signal Select
bits : 0 - 2 (3 bit)
access : read-write
SOURCESEL : Source Select
bits : 16 - 21 (6 bit)
access : read-write
Enumeration:
0x00000000 : NONE
No source selected
0x00000001 : VCMP
Voltage Comparator
0x00000002 : ACMP0
Analog Comparator 0
0x00000003 : ACMP1
Analog Comparator 1
0x00000006 : DAC0
Digital to Analog Converter 0
0x00000008 : ADC0
Analog to Digital Converter 0
0x00000010 : USART0
Universal Synchronous/Asynchronous Receiver/Transmitter 0
0x00000011 : USART1
Universal Synchronous/Asynchronous Receiver/Transmitter 1
0x00000012 : USART2
Universal Synchronous/Asynchronous Receiver/Transmitter 2
0x0000001C : TIMER0
Timer 0
0x0000001D : TIMER1
Timer 1
0x0000001E : TIMER2
Timer 2
0x0000001F : TIMER3
Timer 3
0x00000028 : RTC
Real-Time Counter
0x00000029 : UART0
Universal Asynchronous Receiver/Transmitter 0
0x0000002A : UART1
Universal Asynchronous Receiver/Transmitter 1
0x00000030 : GPIOL
General purpose Input/Output
0x00000031 : GPIOH
General purpose Input/Output
0x00000034 : LETIMER0
Low Energy Timer 0
0x00000037 : BURTC
Backup RTC
0x00000039 : LESENSEL
Low Energy Sensor Interface
0x0000003A : LESENSEH
Low Energy Sensor Interface
0x0000003B : LESENSED
Low Energy Sensor Interface
End of enumeration elements list.
EDSEL : Edge Detect Select
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
0x00000000 : OFF
Signal is left as it is
0x00000001 : POSEDGE
A one HFPERCLK cycle pulse is generated for every positive edge of the incoming signal
0x00000002 : NEGEDGE
A one HFPERCLK clock cycle pulse is generated for every negative edge of the incoming signal
0x00000003 : BOTHEDGES
A one HFPERCLK clock cycle pulse is generated for every edge of the incoming signal
End of enumeration elements list.
ASYNC : Asynchronous reflex
bits : 28 - 28 (1 bit)
access : read-write
Channel Control Register
address_offset : 0x30 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
SIGSEL : Signal Select
bits : 0 - 2 (3 bit)
access : read-write
SOURCESEL : Source Select
bits : 16 - 21 (6 bit)
access : read-write
Enumeration:
0x00000000 : NONE
No source selected
0x00000001 : VCMP
Voltage Comparator
0x00000002 : ACMP0
Analog Comparator 0
0x00000003 : ACMP1
Analog Comparator 1
0x00000006 : DAC0
Digital to Analog Converter 0
0x00000008 : ADC0
Analog to Digital Converter 0
0x00000010 : USART0
Universal Synchronous/Asynchronous Receiver/Transmitter 0
0x00000011 : USART1
Universal Synchronous/Asynchronous Receiver/Transmitter 1
0x00000012 : USART2
Universal Synchronous/Asynchronous Receiver/Transmitter 2
0x0000001C : TIMER0
Timer 0
0x0000001D : TIMER1
Timer 1
0x0000001E : TIMER2
Timer 2
0x0000001F : TIMER3
Timer 3
0x00000028 : RTC
Real-Time Counter
0x00000029 : UART0
Universal Asynchronous Receiver/Transmitter 0
0x0000002A : UART1
Universal Asynchronous Receiver/Transmitter 1
0x00000030 : GPIOL
General purpose Input/Output
0x00000031 : GPIOH
General purpose Input/Output
0x00000034 : LETIMER0
Low Energy Timer 0
0x00000037 : BURTC
Backup RTC
0x00000039 : LESENSEL
Low Energy Sensor Interface
0x0000003A : LESENSEH
Low Energy Sensor Interface
0x0000003B : LESENSED
Low Energy Sensor Interface
End of enumeration elements list.
EDSEL : Edge Detect Select
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
0x00000000 : OFF
Signal is left as it is
0x00000001 : POSEDGE
A one HFPERCLK cycle pulse is generated for every positive edge of the incoming signal
0x00000002 : NEGEDGE
A one HFPERCLK clock cycle pulse is generated for every negative edge of the incoming signal
0x00000003 : BOTHEDGES
A one HFPERCLK clock cycle pulse is generated for every edge of the incoming signal
End of enumeration elements list.
ASYNC : Asynchronous reflex
bits : 28 - 28 (1 bit)
access : read-write
Channel Control Register
address_offset : 0x34 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
SIGSEL : Signal Select
bits : 0 - 2 (3 bit)
access : read-write
SOURCESEL : Source Select
bits : 16 - 21 (6 bit)
access : read-write
Enumeration:
0x00000000 : NONE
No source selected
0x00000001 : VCMP
Voltage Comparator
0x00000002 : ACMP0
Analog Comparator 0
0x00000003 : ACMP1
Analog Comparator 1
0x00000006 : DAC0
Digital to Analog Converter 0
0x00000008 : ADC0
Analog to Digital Converter 0
0x00000010 : USART0
Universal Synchronous/Asynchronous Receiver/Transmitter 0
0x00000011 : USART1
Universal Synchronous/Asynchronous Receiver/Transmitter 1
0x00000012 : USART2
Universal Synchronous/Asynchronous Receiver/Transmitter 2
0x0000001C : TIMER0
Timer 0
0x0000001D : TIMER1
Timer 1
0x0000001E : TIMER2
Timer 2
0x0000001F : TIMER3
Timer 3
0x00000028 : RTC
Real-Time Counter
0x00000029 : UART0
Universal Asynchronous Receiver/Transmitter 0
0x0000002A : UART1
Universal Asynchronous Receiver/Transmitter 1
0x00000030 : GPIOL
General purpose Input/Output
0x00000031 : GPIOH
General purpose Input/Output
0x00000034 : LETIMER0
Low Energy Timer 0
0x00000037 : BURTC
Backup RTC
0x00000039 : LESENSEL
Low Energy Sensor Interface
0x0000003A : LESENSEH
Low Energy Sensor Interface
0x0000003B : LESENSED
Low Energy Sensor Interface
End of enumeration elements list.
EDSEL : Edge Detect Select
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
0x00000000 : OFF
Signal is left as it is
0x00000001 : POSEDGE
A one HFPERCLK cycle pulse is generated for every positive edge of the incoming signal
0x00000002 : NEGEDGE
A one HFPERCLK clock cycle pulse is generated for every negative edge of the incoming signal
0x00000003 : BOTHEDGES
A one HFPERCLK clock cycle pulse is generated for every edge of the incoming signal
End of enumeration elements list.
ASYNC : Asynchronous reflex
bits : 28 - 28 (1 bit)
access : read-write
Channel Control Register
address_offset : 0x38 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
SIGSEL : Signal Select
bits : 0 - 2 (3 bit)
access : read-write
SOURCESEL : Source Select
bits : 16 - 21 (6 bit)
access : read-write
Enumeration:
0x00000000 : NONE
No source selected
0x00000001 : VCMP
Voltage Comparator
0x00000002 : ACMP0
Analog Comparator 0
0x00000003 : ACMP1
Analog Comparator 1
0x00000006 : DAC0
Digital to Analog Converter 0
0x00000008 : ADC0
Analog to Digital Converter 0
0x00000010 : USART0
Universal Synchronous/Asynchronous Receiver/Transmitter 0
0x00000011 : USART1
Universal Synchronous/Asynchronous Receiver/Transmitter 1
0x00000012 : USART2
Universal Synchronous/Asynchronous Receiver/Transmitter 2
0x0000001C : TIMER0
Timer 0
0x0000001D : TIMER1
Timer 1
0x0000001E : TIMER2
Timer 2
0x0000001F : TIMER3
Timer 3
0x00000028 : RTC
Real-Time Counter
0x00000029 : UART0
Universal Asynchronous Receiver/Transmitter 0
0x0000002A : UART1
Universal Asynchronous Receiver/Transmitter 1
0x00000030 : GPIOL
General purpose Input/Output
0x00000031 : GPIOH
General purpose Input/Output
0x00000034 : LETIMER0
Low Energy Timer 0
0x00000037 : BURTC
Backup RTC
0x00000039 : LESENSEL
Low Energy Sensor Interface
0x0000003A : LESENSEH
Low Energy Sensor Interface
0x0000003B : LESENSED
Low Energy Sensor Interface
End of enumeration elements list.
EDSEL : Edge Detect Select
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
0x00000000 : OFF
Signal is left as it is
0x00000001 : POSEDGE
A one HFPERCLK cycle pulse is generated for every positive edge of the incoming signal
0x00000002 : NEGEDGE
A one HFPERCLK clock cycle pulse is generated for every negative edge of the incoming signal
0x00000003 : BOTHEDGES
A one HFPERCLK clock cycle pulse is generated for every edge of the incoming signal
End of enumeration elements list.
ASYNC : Asynchronous reflex
bits : 28 - 28 (1 bit)
access : read-write
Channel Control Register
address_offset : 0x3C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
SIGSEL : Signal Select
bits : 0 - 2 (3 bit)
access : read-write
SOURCESEL : Source Select
bits : 16 - 21 (6 bit)
access : read-write
Enumeration:
0x00000000 : NONE
No source selected
0x00000001 : VCMP
Voltage Comparator
0x00000002 : ACMP0
Analog Comparator 0
0x00000003 : ACMP1
Analog Comparator 1
0x00000006 : DAC0
Digital to Analog Converter 0
0x00000008 : ADC0
Analog to Digital Converter 0
0x00000010 : USART0
Universal Synchronous/Asynchronous Receiver/Transmitter 0
0x00000011 : USART1
Universal Synchronous/Asynchronous Receiver/Transmitter 1
0x00000012 : USART2
Universal Synchronous/Asynchronous Receiver/Transmitter 2
0x0000001C : TIMER0
Timer 0
0x0000001D : TIMER1
Timer 1
0x0000001E : TIMER2
Timer 2
0x0000001F : TIMER3
Timer 3
0x00000028 : RTC
Real-Time Counter
0x00000029 : UART0
Universal Asynchronous Receiver/Transmitter 0
0x0000002A : UART1
Universal Asynchronous Receiver/Transmitter 1
0x00000030 : GPIOL
General purpose Input/Output
0x00000031 : GPIOH
General purpose Input/Output
0x00000034 : LETIMER0
Low Energy Timer 0
0x00000037 : BURTC
Backup RTC
0x00000039 : LESENSEL
Low Energy Sensor Interface
0x0000003A : LESENSEH
Low Energy Sensor Interface
0x0000003B : LESENSED
Low Energy Sensor Interface
End of enumeration elements list.
EDSEL : Edge Detect Select
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
0x00000000 : OFF
Signal is left as it is
0x00000001 : POSEDGE
A one HFPERCLK cycle pulse is generated for every positive edge of the incoming signal
0x00000002 : NEGEDGE
A one HFPERCLK clock cycle pulse is generated for every negative edge of the incoming signal
0x00000003 : BOTHEDGES
A one HFPERCLK clock cycle pulse is generated for every edge of the incoming signal
End of enumeration elements list.
ASYNC : Asynchronous reflex
bits : 28 - 28 (1 bit)
access : read-write
Software Level Register
address_offset : 0x4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
CH0LEVEL : Channel 0 Software Level
bits : 0 - 0 (1 bit)
access : read-write
CH1LEVEL : Channel 1 Software Level
bits : 1 - 1 (1 bit)
access : read-write
CH2LEVEL : Channel 2 Software Level
bits : 2 - 2 (1 bit)
access : read-write
CH3LEVEL : Channel 3 Software Level
bits : 3 - 3 (1 bit)
access : read-write
CH4LEVEL : Channel 4 Software Level
bits : 4 - 4 (1 bit)
access : read-write
CH5LEVEL : Channel 5 Software Level
bits : 5 - 5 (1 bit)
access : read-write
CH6LEVEL : Channel 6 Software Level
bits : 6 - 6 (1 bit)
access : read-write
CH7LEVEL : Channel 7 Software Level
bits : 7 - 7 (1 bit)
access : read-write
CH8LEVEL : Channel 8 Software Level
bits : 8 - 8 (1 bit)
access : read-write
CH9LEVEL : Channel 9 Software Level
bits : 9 - 9 (1 bit)
access : read-write
CH10LEVEL : Channel 10 Software Level
bits : 10 - 10 (1 bit)
access : read-write
CH11LEVEL : Channel 11 Software Level
bits : 11 - 11 (1 bit)
access : read-write
I/O Routing Register
address_offset : 0x8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
CH0PEN : CH0 Pin Enable
bits : 0 - 0 (1 bit)
access : read-write
CH1PEN : CH1 Pin Enable
bits : 1 - 1 (1 bit)
access : read-write
CH2PEN : CH2 Pin Enable
bits : 2 - 2 (1 bit)
access : read-write
CH3PEN : CH3 Pin Enable
bits : 3 - 3 (1 bit)
access : read-write
LOCATION : I/O Location
bits : 8 - 10 (3 bit)
access : read-write
Enumeration:
0x00000000 : LOC0
Location 0
0x00000001 : LOC1
Location 1
End of enumeration elements list.
Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !
This website is sponsored by Embeetle, an IDE designed from scratch for embedded software developers.