\n
address_offset : 0x0 Bytes (0x0)
size : 0x400 byte (0x0)
mem_usage : registers
protection : not protected
Control Register
address_offset : 0x0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
SCANMODE : Configure Scan Mode
bits : 0 - 1 (2 bit)
access : read-write
Enumeration:
0x00000000 : PERIODIC
A new scan is started each time the period counter overflows
0x00000001 : ONESHOT
A single scan is performed when START in CMD is set
0x00000002 : PRS
Pulse on PRS channel
End of enumeration elements list.
PRSSEL : Scan Start PRS Select
bits : 2 - 5 (4 bit)
access : read-write
Enumeration:
0x00000000 : PRSCH0
PRS Channel 0 selected as input
0x00000001 : PRSCH1
PRS Channel 1 selected as input
0x00000002 : PRSCH2
PRS Channel 2 selected as input
0x00000003 : PRSCH3
PRS Channel 3 selected as input
0x00000004 : PRSCH4
PRS Channel 4 selected as input
0x00000005 : PRSCH5
PRS Channel 5 selected as input
0x00000006 : PRSCH6
PRS Channel 6 selected as input
0x00000007 : PRSCH7
PRS Channel 7 selected as input
0x00000008 : PRSCH8
PRS Channel 8 selected as input
0x00000009 : PRSCH9
PRS Channel 9 selected as input
0x0000000A : PRSCH10
PRS Channel 10 selected as input
0x0000000B : PRSCH11
PRS Channel 11 selected as input
End of enumeration elements list.
SCANCONF : Select Scan Configuration
bits : 7 - 8 (2 bit)
access : read-write
Enumeration:
0x00000000 : DIRMAP
The channel configuration register registers used are directly mapped to the channel number.
0x00000001 : INVMAP
The channel configuration register registers used are CHX+8_CONF for channels 0-7 and CHX-8_CONF for channels 8-15.
0x00000002 : TOGGLE
The channel configuration register registers used toggles between CHX_CONF and CHX+8_CONF when channel x triggers
0x00000003 : DECDEF
The decoder state defines the CONF registers to be used.
End of enumeration elements list.
ALTEXMAP : Alternative Excitation Map
bits : 11 - 11 (1 bit)
access : read-write
DUALSAMPLE : Enable Dual Sample Mode
bits : 13 - 13 (1 bit)
access : read-write
BUFOW : Result Buffer Overwrite
bits : 16 - 16 (1 bit)
access : read-write
STRSCANRES : Enable Storing of SCANRES
bits : 17 - 17 (1 bit)
access : read-write
BUFIDL : Result Buffer Interrupt and DMA Trigger Level
bits : 19 - 19 (1 bit)
access : read-write
DMAWU : DMA Wake-up From EM2
bits : 20 - 21 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
No DMA wake-up from EM2
0x00000001 : BUFDATAV
DMA wake-up from EM2 when data is valid in the result buffer
0x00000002 : BUFLEVEL
DMA wake-up from EM2 when the result buffer is full/half-full depending on BUFIDL configuration
End of enumeration elements list.
DEBUGRUN : Debug Mode Run Enable
bits : 22 - 22 (1 bit)
access : read-write
Bias Control Register
address_offset : 0x10 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
BIASMODE : Select Bias Mode
bits : 0 - 1 (2 bit)
access : read-write
Enumeration:
0x00000000 : DONTTOUCH
Bias module is controlled by the EMU and is not affected by LESENSE
0x00000001 : DUTYCYCLE
Bias module duty cycled between low power and high accuracy mode
0x00000002 : HIGHACC
Bias module always in high accuracy mode
End of enumeration elements list.
State Transition Configuration a
address_offset : 0x100 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
CHAIN : Enable State Descriptor Chaining
bits : 14 - 14 (1 bit)
access : read-write
SETIF : Set Interrupt Flag Enable
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration B
address_offset : 0x104 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
SETIF : Set Interrupt Flag
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration a
address_offset : 0x108 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
CHAIN : Enable State Descriptor Chaining
bits : 14 - 14 (1 bit)
access : read-write
SETIF : Set Interrupt Flag Enable
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration B
address_offset : 0x10C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
SETIF : Set Interrupt Flag
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration a
address_offset : 0x110 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
CHAIN : Enable State Descriptor Chaining
bits : 14 - 14 (1 bit)
access : read-write
SETIF : Set Interrupt Flag Enable
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration B
address_offset : 0x114 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
SETIF : Set Interrupt Flag
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration a
address_offset : 0x118 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
CHAIN : Enable State Descriptor Chaining
bits : 14 - 14 (1 bit)
access : read-write
SETIF : Set Interrupt Flag Enable
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration B
address_offset : 0x11C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
SETIF : Set Interrupt Flag
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration a
address_offset : 0x120 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
CHAIN : Enable State Descriptor Chaining
bits : 14 - 14 (1 bit)
access : read-write
SETIF : Set Interrupt Flag Enable
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration B
address_offset : 0x124 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
SETIF : Set Interrupt Flag
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration a
address_offset : 0x128 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
CHAIN : Enable State Descriptor Chaining
bits : 14 - 14 (1 bit)
access : read-write
SETIF : Set Interrupt Flag Enable
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration B
address_offset : 0x12C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
SETIF : Set Interrupt Flag
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration a
address_offset : 0x130 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
CHAIN : Enable State Descriptor Chaining
bits : 14 - 14 (1 bit)
access : read-write
SETIF : Set Interrupt Flag Enable
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration B
address_offset : 0x134 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
SETIF : Set Interrupt Flag
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration a
address_offset : 0x138 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
CHAIN : Enable State Descriptor Chaining
bits : 14 - 14 (1 bit)
access : read-write
SETIF : Set Interrupt Flag Enable
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration B
address_offset : 0x13C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
SETIF : Set Interrupt Flag
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
LESENSE Evaluation Control
address_offset : 0x14 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
WINSIZE : Sliding Window and Step Detection Size
bits : 0 - 15 (16 bit)
access : read-write
State Transition Configuration a
address_offset : 0x140 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
CHAIN : Enable State Descriptor Chaining
bits : 14 - 14 (1 bit)
access : read-write
SETIF : Set Interrupt Flag Enable
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration B
address_offset : 0x144 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
SETIF : Set Interrupt Flag
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration a
address_offset : 0x148 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
CHAIN : Enable State Descriptor Chaining
bits : 14 - 14 (1 bit)
access : read-write
SETIF : Set Interrupt Flag Enable
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration B
address_offset : 0x14C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
SETIF : Set Interrupt Flag
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration a
address_offset : 0x150 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
CHAIN : Enable State Descriptor Chaining
bits : 14 - 14 (1 bit)
access : read-write
SETIF : Set Interrupt Flag Enable
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration B
address_offset : 0x154 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
SETIF : Set Interrupt Flag
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration a
address_offset : 0x158 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
CHAIN : Enable State Descriptor Chaining
bits : 14 - 14 (1 bit)
access : read-write
SETIF : Set Interrupt Flag Enable
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration B
address_offset : 0x15C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
SETIF : Set Interrupt Flag
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration a
address_offset : 0x160 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
CHAIN : Enable State Descriptor Chaining
bits : 14 - 14 (1 bit)
access : read-write
SETIF : Set Interrupt Flag Enable
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration B
address_offset : 0x164 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
SETIF : Set Interrupt Flag
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration a
address_offset : 0x168 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
CHAIN : Enable State Descriptor Chaining
bits : 14 - 14 (1 bit)
access : read-write
SETIF : Set Interrupt Flag Enable
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration B
address_offset : 0x16C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
SETIF : Set Interrupt Flag
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration a
address_offset : 0x170 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
CHAIN : Enable State Descriptor Chaining
bits : 14 - 14 (1 bit)
access : read-write
SETIF : Set Interrupt Flag Enable
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration B
address_offset : 0x174 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
SETIF : Set Interrupt Flag
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration a
address_offset : 0x178 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
CHAIN : Enable State Descriptor Chaining
bits : 14 - 14 (1 bit)
access : read-write
SETIF : Set Interrupt Flag Enable
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration B
address_offset : 0x17C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
SETIF : Set Interrupt Flag
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
PRS Control Register
address_offset : 0x18 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DECCMPVAL : Decoder State Compare Value
bits : 0 - 4 (5 bit)
access : read-write
DECCMPMASK : Decoder State Compare Value Mask
bits : 8 - 12 (5 bit)
access : read-write
DECCMPEN : Enable PRS Output DECCMP
bits : 16 - 16 (1 bit)
access : read-write
State Transition Configuration a
address_offset : 0x180 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
CHAIN : Enable State Descriptor Chaining
bits : 14 - 14 (1 bit)
access : read-write
SETIF : Set Interrupt Flag Enable
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration B
address_offset : 0x184 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
SETIF : Set Interrupt Flag
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration a
address_offset : 0x188 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
CHAIN : Enable State Descriptor Chaining
bits : 14 - 14 (1 bit)
access : read-write
SETIF : Set Interrupt Flag Enable
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration B
address_offset : 0x18C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
SETIF : Set Interrupt Flag
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration a
address_offset : 0x190 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
CHAIN : Enable State Descriptor Chaining
bits : 14 - 14 (1 bit)
access : read-write
SETIF : Set Interrupt Flag Enable
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration B
address_offset : 0x194 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
SETIF : Set Interrupt Flag
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration a
address_offset : 0x198 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
CHAIN : Enable State Descriptor Chaining
bits : 14 - 14 (1 bit)
access : read-write
SETIF : Set Interrupt Flag Enable
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration B
address_offset : 0x19C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
SETIF : Set Interrupt Flag
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration a
address_offset : 0x1A0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
CHAIN : Enable State Descriptor Chaining
bits : 14 - 14 (1 bit)
access : read-write
SETIF : Set Interrupt Flag Enable
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration B
address_offset : 0x1A4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
SETIF : Set Interrupt Flag
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration a
address_offset : 0x1A8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
CHAIN : Enable State Descriptor Chaining
bits : 14 - 14 (1 bit)
access : read-write
SETIF : Set Interrupt Flag Enable
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration B
address_offset : 0x1AC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
SETIF : Set Interrupt Flag
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration a
address_offset : 0x1B0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
CHAIN : Enable State Descriptor Chaining
bits : 14 - 14 (1 bit)
access : read-write
SETIF : Set Interrupt Flag Enable
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration B
address_offset : 0x1B4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
SETIF : Set Interrupt Flag
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration a
address_offset : 0x1B8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
CHAIN : Enable State Descriptor Chaining
bits : 14 - 14 (1 bit)
access : read-write
SETIF : Set Interrupt Flag Enable
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration B
address_offset : 0x1BC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
SETIF : Set Interrupt Flag
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
Command Register
address_offset : 0x1C Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
START : Start Scanning of Sensors
bits : 0 - 0 (1 bit)
access : write-only
STOP : Stop Scanning of Sensors
bits : 1 - 1 (1 bit)
access : write-only
DECODE : Start Decoder
bits : 2 - 2 (1 bit)
access : write-only
CLEARBUF : Clear Result Buffer
bits : 3 - 3 (1 bit)
access : write-only
State Transition Configuration a
address_offset : 0x1C0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
CHAIN : Enable State Descriptor Chaining
bits : 14 - 14 (1 bit)
access : read-write
SETIF : Set Interrupt Flag Enable
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration B
address_offset : 0x1C4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
SETIF : Set Interrupt Flag
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration a
address_offset : 0x1C8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
CHAIN : Enable State Descriptor Chaining
bits : 14 - 14 (1 bit)
access : read-write
SETIF : Set Interrupt Flag Enable
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration B
address_offset : 0x1CC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
SETIF : Set Interrupt Flag
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration a
address_offset : 0x1D0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
CHAIN : Enable State Descriptor Chaining
bits : 14 - 14 (1 bit)
access : read-write
SETIF : Set Interrupt Flag Enable
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration B
address_offset : 0x1D4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
SETIF : Set Interrupt Flag
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration a
address_offset : 0x1D8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
CHAIN : Enable State Descriptor Chaining
bits : 14 - 14 (1 bit)
access : read-write
SETIF : Set Interrupt Flag Enable
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration B
address_offset : 0x1DC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
SETIF : Set Interrupt Flag
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration a
address_offset : 0x1E0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
CHAIN : Enable State Descriptor Chaining
bits : 14 - 14 (1 bit)
access : read-write
SETIF : Set Interrupt Flag Enable
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration B
address_offset : 0x1E4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
SETIF : Set Interrupt Flag
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration a
address_offset : 0x1E8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
CHAIN : Enable State Descriptor Chaining
bits : 14 - 14 (1 bit)
access : read-write
SETIF : Set Interrupt Flag Enable
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration B
address_offset : 0x1EC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
SETIF : Set Interrupt Flag
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration a
address_offset : 0x1F0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
CHAIN : Enable State Descriptor Chaining
bits : 14 - 14 (1 bit)
access : read-write
SETIF : Set Interrupt Flag Enable
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration B
address_offset : 0x1F4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
SETIF : Set Interrupt Flag
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration a
address_offset : 0x1F8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
CHAIN : Enable State Descriptor Chaining
bits : 14 - 14 (1 bit)
access : read-write
SETIF : Set Interrupt Flag Enable
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration B
address_offset : 0x1FC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
SETIF : Set Interrupt Flag
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
Channel Enable Register
address_offset : 0x20 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
CHEN : Enable Scan Channel
bits : 0 - 15 (16 bit)
access : read-write
Scan Results
address_offset : 0x200 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA : Scan Result Buffer
bits : 0 - 15 (16 bit)
access : read-write
DATASRC : Result Data Source
bits : 16 - 19 (4 bit)
access : read-only
Scan Results
address_offset : 0x204 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA : Scan Result Buffer
bits : 0 - 15 (16 bit)
access : read-write
DATASRC : Result Data Source
bits : 16 - 19 (4 bit)
access : read-only
Scan Results
address_offset : 0x208 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA : Scan Result Buffer
bits : 0 - 15 (16 bit)
access : read-write
DATASRC : Result Data Source
bits : 16 - 19 (4 bit)
access : read-only
Scan Results
address_offset : 0x20C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA : Scan Result Buffer
bits : 0 - 15 (16 bit)
access : read-write
DATASRC : Result Data Source
bits : 16 - 19 (4 bit)
access : read-only
Scan Results
address_offset : 0x210 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA : Scan Result Buffer
bits : 0 - 15 (16 bit)
access : read-write
DATASRC : Result Data Source
bits : 16 - 19 (4 bit)
access : read-only
Scan Results
address_offset : 0x214 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA : Scan Result Buffer
bits : 0 - 15 (16 bit)
access : read-write
DATASRC : Result Data Source
bits : 16 - 19 (4 bit)
access : read-only
Scan Results
address_offset : 0x218 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA : Scan Result Buffer
bits : 0 - 15 (16 bit)
access : read-write
DATASRC : Result Data Source
bits : 16 - 19 (4 bit)
access : read-only
Scan Results
address_offset : 0x21C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA : Scan Result Buffer
bits : 0 - 15 (16 bit)
access : read-write
DATASRC : Result Data Source
bits : 16 - 19 (4 bit)
access : read-only
Scan Results
address_offset : 0x220 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA : Scan Result Buffer
bits : 0 - 15 (16 bit)
access : read-write
DATASRC : Result Data Source
bits : 16 - 19 (4 bit)
access : read-only
Scan Results
address_offset : 0x224 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA : Scan Result Buffer
bits : 0 - 15 (16 bit)
access : read-write
DATASRC : Result Data Source
bits : 16 - 19 (4 bit)
access : read-only
Scan Results
address_offset : 0x228 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA : Scan Result Buffer
bits : 0 - 15 (16 bit)
access : read-write
DATASRC : Result Data Source
bits : 16 - 19 (4 bit)
access : read-only
Scan Results
address_offset : 0x22C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA : Scan Result Buffer
bits : 0 - 15 (16 bit)
access : read-write
DATASRC : Result Data Source
bits : 16 - 19 (4 bit)
access : read-only
Scan Results
address_offset : 0x230 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA : Scan Result Buffer
bits : 0 - 15 (16 bit)
access : read-write
DATASRC : Result Data Source
bits : 16 - 19 (4 bit)
access : read-only
Scan Results
address_offset : 0x234 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA : Scan Result Buffer
bits : 0 - 15 (16 bit)
access : read-write
DATASRC : Result Data Source
bits : 16 - 19 (4 bit)
access : read-only
Scan Results
address_offset : 0x238 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA : Scan Result Buffer
bits : 0 - 15 (16 bit)
access : read-write
DATASRC : Result Data Source
bits : 16 - 19 (4 bit)
access : read-only
Scan Results
address_offset : 0x23C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA : Scan Result Buffer
bits : 0 - 15 (16 bit)
access : read-write
DATASRC : Result Data Source
bits : 16 - 19 (4 bit)
access : read-only
Scan Result Register
address_offset : 0x24 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
SCANRES : Scan Results
bits : 0 - 15 (16 bit)
access : read-write
STEPDIR : Direction of Previous Step Detection
bits : 16 - 31 (16 bit)
access : read-write
Scan Configuration
address_offset : 0x240 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXTIME : Set Excitation Time
bits : 0 - 5 (6 bit)
access : read-write
SAMPLEDLY : Set Sample Delay
bits : 6 - 13 (8 bit)
access : read-write
MEASUREDLY : Set Measure Delay
bits : 14 - 23 (10 bit)
access : read-write
Scan Configuration
address_offset : 0x244 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
THRES : ACMP Threshold or VDAC Data
bits : 0 - 11 (12 bit)
access : read-write
SAMPLE : Select Sample Mode
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
0x00000000 : ACMPCOUNT
Counter output will be used in evaluation
0x00000001 : ACMP
ACMP output will be used in evaluation
0x00000002 : ADC
ADC output will be used in evaluation
0x00000003 : ADCDIFF
Differential ADC output will be used in evaluation
End of enumeration elements list.
SETIF : Enable Interrupt Generation
bits : 14 - 16 (3 bit)
access : read-write
Enumeration:
0x00000000 : NONE
No interrupt is generated
0x00000001 : LEVEL
Set interrupt flag if the sensor triggers.
0x00000002 : POSEDGE
Set interrupt flag on positive edge of the sensor state
0x00000003 : NEGEDGE
Set interrupt flag on negative edge of the sensor state
0x00000004 : BOTHEDGES
Set interrupt flag on both edges of the sensor state
End of enumeration elements list.
EXMODE : Set GPIO Mode
bits : 17 - 18 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
Disabled
0x00000001 : HIGH
Push Pull, GPIO is driven high
0x00000002 : LOW
Push Pull, GPIO is driven low
0x00000003 : DACOUT
VDAC output
End of enumeration elements list.
EXCLK : Select Clock Used for Excitation Timing
bits : 19 - 19 (1 bit)
access : read-write
SAMPLECLK : Select Clock Used for Timing of Sample Delay
bits : 20 - 20 (1 bit)
access : read-write
ALTEX : Use Alternative Excite Pin
bits : 21 - 21 (1 bit)
access : read-write
Scan Configuration
address_offset : 0x248 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMPTHRES : Decision Threshold for Sensor Data
bits : 0 - 15 (16 bit)
access : read-write
COMP : Select Mode for Threshold Comparison
bits : 16 - 16 (1 bit)
access : read-write
DECODE : Send Result to Decoder
bits : 17 - 17 (1 bit)
access : read-write
STRSAMPLE : Enable Storing of Sensor Sample in Result Buffer
bits : 18 - 19 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
Nothing will be stored in the result buffer.
0x00000001 : DATA
The sensor sample data will be stored in the result buffer.
0x00000002 : DATASRC
The data source (i.e., the channel) will be stored alongside the sensor sample data.
End of enumeration elements list.
SCANRESINV : Enable Inversion of Result
bits : 20 - 20 (1 bit)
access : read-write
MODE : Configure Evaluation Mode
bits : 21 - 22 (2 bit)
access : read-write
Enumeration:
0x00000000 : THRES
Threshold comparison is used to evaluate sensor result
0x00000001 : SLIDINGWIN
Sliding window is used to evaluate sensor result
0x00000002 : STEPDET
Step detection is used to evaluate sensor result
End of enumeration elements list.
Scan Configuration
address_offset : 0x250 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXTIME : Set Excitation Time
bits : 0 - 5 (6 bit)
access : read-write
SAMPLEDLY : Set Sample Delay
bits : 6 - 13 (8 bit)
access : read-write
MEASUREDLY : Set Measure Delay
bits : 14 - 23 (10 bit)
access : read-write
Scan Configuration
address_offset : 0x254 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
THRES : ACMP Threshold or VDAC Data
bits : 0 - 11 (12 bit)
access : read-write
SAMPLE : Select Sample Mode
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
0x00000000 : ACMPCOUNT
Counter output will be used in evaluation
0x00000001 : ACMP
ACMP output will be used in evaluation
0x00000002 : ADC
ADC output will be used in evaluation
0x00000003 : ADCDIFF
Differential ADC output will be used in evaluation
End of enumeration elements list.
SETIF : Enable Interrupt Generation
bits : 14 - 16 (3 bit)
access : read-write
Enumeration:
0x00000000 : NONE
No interrupt is generated
0x00000001 : LEVEL
Set interrupt flag if the sensor triggers.
0x00000002 : POSEDGE
Set interrupt flag on positive edge of the sensor state
0x00000003 : NEGEDGE
Set interrupt flag on negative edge of the sensor state
0x00000004 : BOTHEDGES
Set interrupt flag on both edges of the sensor state
End of enumeration elements list.
EXMODE : Set GPIO Mode
bits : 17 - 18 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
Disabled
0x00000001 : HIGH
Push Pull, GPIO is driven high
0x00000002 : LOW
Push Pull, GPIO is driven low
0x00000003 : DACOUT
VDAC output
End of enumeration elements list.
EXCLK : Select Clock Used for Excitation Timing
bits : 19 - 19 (1 bit)
access : read-write
SAMPLECLK : Select Clock Used for Timing of Sample Delay
bits : 20 - 20 (1 bit)
access : read-write
ALTEX : Use Alternative Excite Pin
bits : 21 - 21 (1 bit)
access : read-write
Scan Configuration
address_offset : 0x258 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMPTHRES : Decision Threshold for Sensor Data
bits : 0 - 15 (16 bit)
access : read-write
COMP : Select Mode for Threshold Comparison
bits : 16 - 16 (1 bit)
access : read-write
DECODE : Send Result to Decoder
bits : 17 - 17 (1 bit)
access : read-write
STRSAMPLE : Enable Storing of Sensor Sample in Result Buffer
bits : 18 - 19 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
Nothing will be stored in the result buffer.
0x00000001 : DATA
The sensor sample data will be stored in the result buffer.
0x00000002 : DATASRC
The data source (i.e., the channel) will be stored alongside the sensor sample data.
End of enumeration elements list.
SCANRESINV : Enable Inversion of Result
bits : 20 - 20 (1 bit)
access : read-write
MODE : Configure Evaluation Mode
bits : 21 - 22 (2 bit)
access : read-write
Enumeration:
0x00000000 : THRES
Threshold comparison is used to evaluate sensor result
0x00000001 : SLIDINGWIN
Sliding window is used to evaluate sensor result
0x00000002 : STEPDET
Step detection is used to evaluate sensor result
End of enumeration elements list.
Scan Configuration
address_offset : 0x260 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXTIME : Set Excitation Time
bits : 0 - 5 (6 bit)
access : read-write
SAMPLEDLY : Set Sample Delay
bits : 6 - 13 (8 bit)
access : read-write
MEASUREDLY : Set Measure Delay
bits : 14 - 23 (10 bit)
access : read-write
Scan Configuration
address_offset : 0x264 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
THRES : ACMP Threshold or VDAC Data
bits : 0 - 11 (12 bit)
access : read-write
SAMPLE : Select Sample Mode
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
0x00000000 : ACMPCOUNT
Counter output will be used in evaluation
0x00000001 : ACMP
ACMP output will be used in evaluation
0x00000002 : ADC
ADC output will be used in evaluation
0x00000003 : ADCDIFF
Differential ADC output will be used in evaluation
End of enumeration elements list.
SETIF : Enable Interrupt Generation
bits : 14 - 16 (3 bit)
access : read-write
Enumeration:
0x00000000 : NONE
No interrupt is generated
0x00000001 : LEVEL
Set interrupt flag if the sensor triggers.
0x00000002 : POSEDGE
Set interrupt flag on positive edge of the sensor state
0x00000003 : NEGEDGE
Set interrupt flag on negative edge of the sensor state
0x00000004 : BOTHEDGES
Set interrupt flag on both edges of the sensor state
End of enumeration elements list.
EXMODE : Set GPIO Mode
bits : 17 - 18 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
Disabled
0x00000001 : HIGH
Push Pull, GPIO is driven high
0x00000002 : LOW
Push Pull, GPIO is driven low
0x00000003 : DACOUT
VDAC output
End of enumeration elements list.
EXCLK : Select Clock Used for Excitation Timing
bits : 19 - 19 (1 bit)
access : read-write
SAMPLECLK : Select Clock Used for Timing of Sample Delay
bits : 20 - 20 (1 bit)
access : read-write
ALTEX : Use Alternative Excite Pin
bits : 21 - 21 (1 bit)
access : read-write
Scan Configuration
address_offset : 0x268 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMPTHRES : Decision Threshold for Sensor Data
bits : 0 - 15 (16 bit)
access : read-write
COMP : Select Mode for Threshold Comparison
bits : 16 - 16 (1 bit)
access : read-write
DECODE : Send Result to Decoder
bits : 17 - 17 (1 bit)
access : read-write
STRSAMPLE : Enable Storing of Sensor Sample in Result Buffer
bits : 18 - 19 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
Nothing will be stored in the result buffer.
0x00000001 : DATA
The sensor sample data will be stored in the result buffer.
0x00000002 : DATASRC
The data source (i.e., the channel) will be stored alongside the sensor sample data.
End of enumeration elements list.
SCANRESINV : Enable Inversion of Result
bits : 20 - 20 (1 bit)
access : read-write
MODE : Configure Evaluation Mode
bits : 21 - 22 (2 bit)
access : read-write
Enumeration:
0x00000000 : THRES
Threshold comparison is used to evaluate sensor result
0x00000001 : SLIDINGWIN
Sliding window is used to evaluate sensor result
0x00000002 : STEPDET
Step detection is used to evaluate sensor result
End of enumeration elements list.
Scan Configuration
address_offset : 0x270 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXTIME : Set Excitation Time
bits : 0 - 5 (6 bit)
access : read-write
SAMPLEDLY : Set Sample Delay
bits : 6 - 13 (8 bit)
access : read-write
MEASUREDLY : Set Measure Delay
bits : 14 - 23 (10 bit)
access : read-write
Scan Configuration
address_offset : 0x274 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
THRES : ACMP Threshold or VDAC Data
bits : 0 - 11 (12 bit)
access : read-write
SAMPLE : Select Sample Mode
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
0x00000000 : ACMPCOUNT
Counter output will be used in evaluation
0x00000001 : ACMP
ACMP output will be used in evaluation
0x00000002 : ADC
ADC output will be used in evaluation
0x00000003 : ADCDIFF
Differential ADC output will be used in evaluation
End of enumeration elements list.
SETIF : Enable Interrupt Generation
bits : 14 - 16 (3 bit)
access : read-write
Enumeration:
0x00000000 : NONE
No interrupt is generated
0x00000001 : LEVEL
Set interrupt flag if the sensor triggers.
0x00000002 : POSEDGE
Set interrupt flag on positive edge of the sensor state
0x00000003 : NEGEDGE
Set interrupt flag on negative edge of the sensor state
0x00000004 : BOTHEDGES
Set interrupt flag on both edges of the sensor state
End of enumeration elements list.
EXMODE : Set GPIO Mode
bits : 17 - 18 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
Disabled
0x00000001 : HIGH
Push Pull, GPIO is driven high
0x00000002 : LOW
Push Pull, GPIO is driven low
0x00000003 : DACOUT
VDAC output
End of enumeration elements list.
EXCLK : Select Clock Used for Excitation Timing
bits : 19 - 19 (1 bit)
access : read-write
SAMPLECLK : Select Clock Used for Timing of Sample Delay
bits : 20 - 20 (1 bit)
access : read-write
ALTEX : Use Alternative Excite Pin
bits : 21 - 21 (1 bit)
access : read-write
Scan Configuration
address_offset : 0x278 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMPTHRES : Decision Threshold for Sensor Data
bits : 0 - 15 (16 bit)
access : read-write
COMP : Select Mode for Threshold Comparison
bits : 16 - 16 (1 bit)
access : read-write
DECODE : Send Result to Decoder
bits : 17 - 17 (1 bit)
access : read-write
STRSAMPLE : Enable Storing of Sensor Sample in Result Buffer
bits : 18 - 19 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
Nothing will be stored in the result buffer.
0x00000001 : DATA
The sensor sample data will be stored in the result buffer.
0x00000002 : DATASRC
The data source (i.e., the channel) will be stored alongside the sensor sample data.
End of enumeration elements list.
SCANRESINV : Enable Inversion of Result
bits : 20 - 20 (1 bit)
access : read-write
MODE : Configure Evaluation Mode
bits : 21 - 22 (2 bit)
access : read-write
Enumeration:
0x00000000 : THRES
Threshold comparison is used to evaluate sensor result
0x00000001 : SLIDINGWIN
Sliding window is used to evaluate sensor result
0x00000002 : STEPDET
Step detection is used to evaluate sensor result
End of enumeration elements list.
Status Register
address_offset : 0x28 Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
BUFDATAV : Result Data Valid
bits : 0 - 0 (1 bit)
access : read-only
BUFHALFFULL : Result Buffer Half Full
bits : 1 - 1 (1 bit)
access : read-only
BUFFULL : Result Buffer Full
bits : 2 - 2 (1 bit)
access : read-only
RUNNING : LESENSE Periodic Counter Running
bits : 3 - 3 (1 bit)
access : read-only
SCANACTIVE : LESENSE Scan Active
bits : 4 - 4 (1 bit)
access : read-only
DACACTIVE : LESENSE VDAC Interface is Active
bits : 5 - 5 (1 bit)
access : read-only
Scan Configuration
address_offset : 0x280 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXTIME : Set Excitation Time
bits : 0 - 5 (6 bit)
access : read-write
SAMPLEDLY : Set Sample Delay
bits : 6 - 13 (8 bit)
access : read-write
MEASUREDLY : Set Measure Delay
bits : 14 - 23 (10 bit)
access : read-write
Scan Configuration
address_offset : 0x284 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
THRES : ACMP Threshold or VDAC Data
bits : 0 - 11 (12 bit)
access : read-write
SAMPLE : Select Sample Mode
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
0x00000000 : ACMPCOUNT
Counter output will be used in evaluation
0x00000001 : ACMP
ACMP output will be used in evaluation
0x00000002 : ADC
ADC output will be used in evaluation
0x00000003 : ADCDIFF
Differential ADC output will be used in evaluation
End of enumeration elements list.
SETIF : Enable Interrupt Generation
bits : 14 - 16 (3 bit)
access : read-write
Enumeration:
0x00000000 : NONE
No interrupt is generated
0x00000001 : LEVEL
Set interrupt flag if the sensor triggers.
0x00000002 : POSEDGE
Set interrupt flag on positive edge of the sensor state
0x00000003 : NEGEDGE
Set interrupt flag on negative edge of the sensor state
0x00000004 : BOTHEDGES
Set interrupt flag on both edges of the sensor state
End of enumeration elements list.
EXMODE : Set GPIO Mode
bits : 17 - 18 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
Disabled
0x00000001 : HIGH
Push Pull, GPIO is driven high
0x00000002 : LOW
Push Pull, GPIO is driven low
0x00000003 : DACOUT
VDAC output
End of enumeration elements list.
EXCLK : Select Clock Used for Excitation Timing
bits : 19 - 19 (1 bit)
access : read-write
SAMPLECLK : Select Clock Used for Timing of Sample Delay
bits : 20 - 20 (1 bit)
access : read-write
ALTEX : Use Alternative Excite Pin
bits : 21 - 21 (1 bit)
access : read-write
Scan Configuration
address_offset : 0x288 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMPTHRES : Decision Threshold for Sensor Data
bits : 0 - 15 (16 bit)
access : read-write
COMP : Select Mode for Threshold Comparison
bits : 16 - 16 (1 bit)
access : read-write
DECODE : Send Result to Decoder
bits : 17 - 17 (1 bit)
access : read-write
STRSAMPLE : Enable Storing of Sensor Sample in Result Buffer
bits : 18 - 19 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
Nothing will be stored in the result buffer.
0x00000001 : DATA
The sensor sample data will be stored in the result buffer.
0x00000002 : DATASRC
The data source (i.e., the channel) will be stored alongside the sensor sample data.
End of enumeration elements list.
SCANRESINV : Enable Inversion of Result
bits : 20 - 20 (1 bit)
access : read-write
MODE : Configure Evaluation Mode
bits : 21 - 22 (2 bit)
access : read-write
Enumeration:
0x00000000 : THRES
Threshold comparison is used to evaluate sensor result
0x00000001 : SLIDINGWIN
Sliding window is used to evaluate sensor result
0x00000002 : STEPDET
Step detection is used to evaluate sensor result
End of enumeration elements list.
Scan Configuration
address_offset : 0x290 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXTIME : Set Excitation Time
bits : 0 - 5 (6 bit)
access : read-write
SAMPLEDLY : Set Sample Delay
bits : 6 - 13 (8 bit)
access : read-write
MEASUREDLY : Set Measure Delay
bits : 14 - 23 (10 bit)
access : read-write
Scan Configuration
address_offset : 0x294 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
THRES : ACMP Threshold or VDAC Data
bits : 0 - 11 (12 bit)
access : read-write
SAMPLE : Select Sample Mode
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
0x00000000 : ACMPCOUNT
Counter output will be used in evaluation
0x00000001 : ACMP
ACMP output will be used in evaluation
0x00000002 : ADC
ADC output will be used in evaluation
0x00000003 : ADCDIFF
Differential ADC output will be used in evaluation
End of enumeration elements list.
SETIF : Enable Interrupt Generation
bits : 14 - 16 (3 bit)
access : read-write
Enumeration:
0x00000000 : NONE
No interrupt is generated
0x00000001 : LEVEL
Set interrupt flag if the sensor triggers.
0x00000002 : POSEDGE
Set interrupt flag on positive edge of the sensor state
0x00000003 : NEGEDGE
Set interrupt flag on negative edge of the sensor state
0x00000004 : BOTHEDGES
Set interrupt flag on both edges of the sensor state
End of enumeration elements list.
EXMODE : Set GPIO Mode
bits : 17 - 18 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
Disabled
0x00000001 : HIGH
Push Pull, GPIO is driven high
0x00000002 : LOW
Push Pull, GPIO is driven low
0x00000003 : DACOUT
VDAC output
End of enumeration elements list.
EXCLK : Select Clock Used for Excitation Timing
bits : 19 - 19 (1 bit)
access : read-write
SAMPLECLK : Select Clock Used for Timing of Sample Delay
bits : 20 - 20 (1 bit)
access : read-write
ALTEX : Use Alternative Excite Pin
bits : 21 - 21 (1 bit)
access : read-write
Scan Configuration
address_offset : 0x298 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMPTHRES : Decision Threshold for Sensor Data
bits : 0 - 15 (16 bit)
access : read-write
COMP : Select Mode for Threshold Comparison
bits : 16 - 16 (1 bit)
access : read-write
DECODE : Send Result to Decoder
bits : 17 - 17 (1 bit)
access : read-write
STRSAMPLE : Enable Storing of Sensor Sample in Result Buffer
bits : 18 - 19 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
Nothing will be stored in the result buffer.
0x00000001 : DATA
The sensor sample data will be stored in the result buffer.
0x00000002 : DATASRC
The data source (i.e., the channel) will be stored alongside the sensor sample data.
End of enumeration elements list.
SCANRESINV : Enable Inversion of Result
bits : 20 - 20 (1 bit)
access : read-write
MODE : Configure Evaluation Mode
bits : 21 - 22 (2 bit)
access : read-write
Enumeration:
0x00000000 : THRES
Threshold comparison is used to evaluate sensor result
0x00000001 : SLIDINGWIN
Sliding window is used to evaluate sensor result
0x00000002 : STEPDET
Step detection is used to evaluate sensor result
End of enumeration elements list.
Scan Configuration
address_offset : 0x2A0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXTIME : Set Excitation Time
bits : 0 - 5 (6 bit)
access : read-write
SAMPLEDLY : Set Sample Delay
bits : 6 - 13 (8 bit)
access : read-write
MEASUREDLY : Set Measure Delay
bits : 14 - 23 (10 bit)
access : read-write
Scan Configuration
address_offset : 0x2A4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
THRES : ACMP Threshold or VDAC Data
bits : 0 - 11 (12 bit)
access : read-write
SAMPLE : Select Sample Mode
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
0x00000000 : ACMPCOUNT
Counter output will be used in evaluation
0x00000001 : ACMP
ACMP output will be used in evaluation
0x00000002 : ADC
ADC output will be used in evaluation
0x00000003 : ADCDIFF
Differential ADC output will be used in evaluation
End of enumeration elements list.
SETIF : Enable Interrupt Generation
bits : 14 - 16 (3 bit)
access : read-write
Enumeration:
0x00000000 : NONE
No interrupt is generated
0x00000001 : LEVEL
Set interrupt flag if the sensor triggers.
0x00000002 : POSEDGE
Set interrupt flag on positive edge of the sensor state
0x00000003 : NEGEDGE
Set interrupt flag on negative edge of the sensor state
0x00000004 : BOTHEDGES
Set interrupt flag on both edges of the sensor state
End of enumeration elements list.
EXMODE : Set GPIO Mode
bits : 17 - 18 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
Disabled
0x00000001 : HIGH
Push Pull, GPIO is driven high
0x00000002 : LOW
Push Pull, GPIO is driven low
0x00000003 : DACOUT
VDAC output
End of enumeration elements list.
EXCLK : Select Clock Used for Excitation Timing
bits : 19 - 19 (1 bit)
access : read-write
SAMPLECLK : Select Clock Used for Timing of Sample Delay
bits : 20 - 20 (1 bit)
access : read-write
ALTEX : Use Alternative Excite Pin
bits : 21 - 21 (1 bit)
access : read-write
Scan Configuration
address_offset : 0x2A8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMPTHRES : Decision Threshold for Sensor Data
bits : 0 - 15 (16 bit)
access : read-write
COMP : Select Mode for Threshold Comparison
bits : 16 - 16 (1 bit)
access : read-write
DECODE : Send Result to Decoder
bits : 17 - 17 (1 bit)
access : read-write
STRSAMPLE : Enable Storing of Sensor Sample in Result Buffer
bits : 18 - 19 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
Nothing will be stored in the result buffer.
0x00000001 : DATA
The sensor sample data will be stored in the result buffer.
0x00000002 : DATASRC
The data source (i.e., the channel) will be stored alongside the sensor sample data.
End of enumeration elements list.
SCANRESINV : Enable Inversion of Result
bits : 20 - 20 (1 bit)
access : read-write
MODE : Configure Evaluation Mode
bits : 21 - 22 (2 bit)
access : read-write
Enumeration:
0x00000000 : THRES
Threshold comparison is used to evaluate sensor result
0x00000001 : SLIDINGWIN
Sliding window is used to evaluate sensor result
0x00000002 : STEPDET
Step detection is used to evaluate sensor result
End of enumeration elements list.
Scan Configuration
address_offset : 0x2B0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXTIME : Set Excitation Time
bits : 0 - 5 (6 bit)
access : read-write
SAMPLEDLY : Set Sample Delay
bits : 6 - 13 (8 bit)
access : read-write
MEASUREDLY : Set Measure Delay
bits : 14 - 23 (10 bit)
access : read-write
Scan Configuration
address_offset : 0x2B4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
THRES : ACMP Threshold or VDAC Data
bits : 0 - 11 (12 bit)
access : read-write
SAMPLE : Select Sample Mode
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
0x00000000 : ACMPCOUNT
Counter output will be used in evaluation
0x00000001 : ACMP
ACMP output will be used in evaluation
0x00000002 : ADC
ADC output will be used in evaluation
0x00000003 : ADCDIFF
Differential ADC output will be used in evaluation
End of enumeration elements list.
SETIF : Enable Interrupt Generation
bits : 14 - 16 (3 bit)
access : read-write
Enumeration:
0x00000000 : NONE
No interrupt is generated
0x00000001 : LEVEL
Set interrupt flag if the sensor triggers.
0x00000002 : POSEDGE
Set interrupt flag on positive edge of the sensor state
0x00000003 : NEGEDGE
Set interrupt flag on negative edge of the sensor state
0x00000004 : BOTHEDGES
Set interrupt flag on both edges of the sensor state
End of enumeration elements list.
EXMODE : Set GPIO Mode
bits : 17 - 18 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
Disabled
0x00000001 : HIGH
Push Pull, GPIO is driven high
0x00000002 : LOW
Push Pull, GPIO is driven low
0x00000003 : DACOUT
VDAC output
End of enumeration elements list.
EXCLK : Select Clock Used for Excitation Timing
bits : 19 - 19 (1 bit)
access : read-write
SAMPLECLK : Select Clock Used for Timing of Sample Delay
bits : 20 - 20 (1 bit)
access : read-write
ALTEX : Use Alternative Excite Pin
bits : 21 - 21 (1 bit)
access : read-write
Scan Configuration
address_offset : 0x2B8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMPTHRES : Decision Threshold for Sensor Data
bits : 0 - 15 (16 bit)
access : read-write
COMP : Select Mode for Threshold Comparison
bits : 16 - 16 (1 bit)
access : read-write
DECODE : Send Result to Decoder
bits : 17 - 17 (1 bit)
access : read-write
STRSAMPLE : Enable Storing of Sensor Sample in Result Buffer
bits : 18 - 19 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
Nothing will be stored in the result buffer.
0x00000001 : DATA
The sensor sample data will be stored in the result buffer.
0x00000002 : DATASRC
The data source (i.e., the channel) will be stored alongside the sensor sample data.
End of enumeration elements list.
SCANRESINV : Enable Inversion of Result
bits : 20 - 20 (1 bit)
access : read-write
MODE : Configure Evaluation Mode
bits : 21 - 22 (2 bit)
access : read-write
Enumeration:
0x00000000 : THRES
Threshold comparison is used to evaluate sensor result
0x00000001 : SLIDINGWIN
Sliding window is used to evaluate sensor result
0x00000002 : STEPDET
Step detection is used to evaluate sensor result
End of enumeration elements list.
Result Buffer Pointers
address_offset : 0x2C Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
RD : Result Buffer Read Pointer
bits : 0 - 3 (4 bit)
access : read-only
WR : Result Buffer Write Pointer
bits : 4 - 7 (4 bit)
access : read-only
Scan Configuration
address_offset : 0x2C0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXTIME : Set Excitation Time
bits : 0 - 5 (6 bit)
access : read-write
SAMPLEDLY : Set Sample Delay
bits : 6 - 13 (8 bit)
access : read-write
MEASUREDLY : Set Measure Delay
bits : 14 - 23 (10 bit)
access : read-write
Scan Configuration
address_offset : 0x2C4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
THRES : ACMP Threshold or VDAC Data
bits : 0 - 11 (12 bit)
access : read-write
SAMPLE : Select Sample Mode
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
0x00000000 : ACMPCOUNT
Counter output will be used in evaluation
0x00000001 : ACMP
ACMP output will be used in evaluation
0x00000002 : ADC
ADC output will be used in evaluation
0x00000003 : ADCDIFF
Differential ADC output will be used in evaluation
End of enumeration elements list.
SETIF : Enable Interrupt Generation
bits : 14 - 16 (3 bit)
access : read-write
Enumeration:
0x00000000 : NONE
No interrupt is generated
0x00000001 : LEVEL
Set interrupt flag if the sensor triggers.
0x00000002 : POSEDGE
Set interrupt flag on positive edge of the sensor state
0x00000003 : NEGEDGE
Set interrupt flag on negative edge of the sensor state
0x00000004 : BOTHEDGES
Set interrupt flag on both edges of the sensor state
End of enumeration elements list.
EXMODE : Set GPIO Mode
bits : 17 - 18 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
Disabled
0x00000001 : HIGH
Push Pull, GPIO is driven high
0x00000002 : LOW
Push Pull, GPIO is driven low
0x00000003 : DACOUT
VDAC output
End of enumeration elements list.
EXCLK : Select Clock Used for Excitation Timing
bits : 19 - 19 (1 bit)
access : read-write
SAMPLECLK : Select Clock Used for Timing of Sample Delay
bits : 20 - 20 (1 bit)
access : read-write
ALTEX : Use Alternative Excite Pin
bits : 21 - 21 (1 bit)
access : read-write
Scan Configuration
address_offset : 0x2C8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMPTHRES : Decision Threshold for Sensor Data
bits : 0 - 15 (16 bit)
access : read-write
COMP : Select Mode for Threshold Comparison
bits : 16 - 16 (1 bit)
access : read-write
DECODE : Send Result to Decoder
bits : 17 - 17 (1 bit)
access : read-write
STRSAMPLE : Enable Storing of Sensor Sample in Result Buffer
bits : 18 - 19 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
Nothing will be stored in the result buffer.
0x00000001 : DATA
The sensor sample data will be stored in the result buffer.
0x00000002 : DATASRC
The data source (i.e., the channel) will be stored alongside the sensor sample data.
End of enumeration elements list.
SCANRESINV : Enable Inversion of Result
bits : 20 - 20 (1 bit)
access : read-write
MODE : Configure Evaluation Mode
bits : 21 - 22 (2 bit)
access : read-write
Enumeration:
0x00000000 : THRES
Threshold comparison is used to evaluate sensor result
0x00000001 : SLIDINGWIN
Sliding window is used to evaluate sensor result
0x00000002 : STEPDET
Step detection is used to evaluate sensor result
End of enumeration elements list.
Scan Configuration
address_offset : 0x2D0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXTIME : Set Excitation Time
bits : 0 - 5 (6 bit)
access : read-write
SAMPLEDLY : Set Sample Delay
bits : 6 - 13 (8 bit)
access : read-write
MEASUREDLY : Set Measure Delay
bits : 14 - 23 (10 bit)
access : read-write
Scan Configuration
address_offset : 0x2D4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
THRES : ACMP Threshold or VDAC Data
bits : 0 - 11 (12 bit)
access : read-write
SAMPLE : Select Sample Mode
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
0x00000000 : ACMPCOUNT
Counter output will be used in evaluation
0x00000001 : ACMP
ACMP output will be used in evaluation
0x00000002 : ADC
ADC output will be used in evaluation
0x00000003 : ADCDIFF
Differential ADC output will be used in evaluation
End of enumeration elements list.
SETIF : Enable Interrupt Generation
bits : 14 - 16 (3 bit)
access : read-write
Enumeration:
0x00000000 : NONE
No interrupt is generated
0x00000001 : LEVEL
Set interrupt flag if the sensor triggers.
0x00000002 : POSEDGE
Set interrupt flag on positive edge of the sensor state
0x00000003 : NEGEDGE
Set interrupt flag on negative edge of the sensor state
0x00000004 : BOTHEDGES
Set interrupt flag on both edges of the sensor state
End of enumeration elements list.
EXMODE : Set GPIO Mode
bits : 17 - 18 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
Disabled
0x00000001 : HIGH
Push Pull, GPIO is driven high
0x00000002 : LOW
Push Pull, GPIO is driven low
0x00000003 : DACOUT
VDAC output
End of enumeration elements list.
EXCLK : Select Clock Used for Excitation Timing
bits : 19 - 19 (1 bit)
access : read-write
SAMPLECLK : Select Clock Used for Timing of Sample Delay
bits : 20 - 20 (1 bit)
access : read-write
ALTEX : Use Alternative Excite Pin
bits : 21 - 21 (1 bit)
access : read-write
Scan Configuration
address_offset : 0x2D8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMPTHRES : Decision Threshold for Sensor Data
bits : 0 - 15 (16 bit)
access : read-write
COMP : Select Mode for Threshold Comparison
bits : 16 - 16 (1 bit)
access : read-write
DECODE : Send Result to Decoder
bits : 17 - 17 (1 bit)
access : read-write
STRSAMPLE : Enable Storing of Sensor Sample in Result Buffer
bits : 18 - 19 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
Nothing will be stored in the result buffer.
0x00000001 : DATA
The sensor sample data will be stored in the result buffer.
0x00000002 : DATASRC
The data source (i.e., the channel) will be stored alongside the sensor sample data.
End of enumeration elements list.
SCANRESINV : Enable Inversion of Result
bits : 20 - 20 (1 bit)
access : read-write
MODE : Configure Evaluation Mode
bits : 21 - 22 (2 bit)
access : read-write
Enumeration:
0x00000000 : THRES
Threshold comparison is used to evaluate sensor result
0x00000001 : SLIDINGWIN
Sliding window is used to evaluate sensor result
0x00000002 : STEPDET
Step detection is used to evaluate sensor result
End of enumeration elements list.
Scan Configuration
address_offset : 0x2E0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXTIME : Set Excitation Time
bits : 0 - 5 (6 bit)
access : read-write
SAMPLEDLY : Set Sample Delay
bits : 6 - 13 (8 bit)
access : read-write
MEASUREDLY : Set Measure Delay
bits : 14 - 23 (10 bit)
access : read-write
Scan Configuration
address_offset : 0x2E4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
THRES : ACMP Threshold or VDAC Data
bits : 0 - 11 (12 bit)
access : read-write
SAMPLE : Select Sample Mode
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
0x00000000 : ACMPCOUNT
Counter output will be used in evaluation
0x00000001 : ACMP
ACMP output will be used in evaluation
0x00000002 : ADC
ADC output will be used in evaluation
0x00000003 : ADCDIFF
Differential ADC output will be used in evaluation
End of enumeration elements list.
SETIF : Enable Interrupt Generation
bits : 14 - 16 (3 bit)
access : read-write
Enumeration:
0x00000000 : NONE
No interrupt is generated
0x00000001 : LEVEL
Set interrupt flag if the sensor triggers.
0x00000002 : POSEDGE
Set interrupt flag on positive edge of the sensor state
0x00000003 : NEGEDGE
Set interrupt flag on negative edge of the sensor state
0x00000004 : BOTHEDGES
Set interrupt flag on both edges of the sensor state
End of enumeration elements list.
EXMODE : Set GPIO Mode
bits : 17 - 18 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
Disabled
0x00000001 : HIGH
Push Pull, GPIO is driven high
0x00000002 : LOW
Push Pull, GPIO is driven low
0x00000003 : DACOUT
VDAC output
End of enumeration elements list.
EXCLK : Select Clock Used for Excitation Timing
bits : 19 - 19 (1 bit)
access : read-write
SAMPLECLK : Select Clock Used for Timing of Sample Delay
bits : 20 - 20 (1 bit)
access : read-write
ALTEX : Use Alternative Excite Pin
bits : 21 - 21 (1 bit)
access : read-write
Scan Configuration
address_offset : 0x2E8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMPTHRES : Decision Threshold for Sensor Data
bits : 0 - 15 (16 bit)
access : read-write
COMP : Select Mode for Threshold Comparison
bits : 16 - 16 (1 bit)
access : read-write
DECODE : Send Result to Decoder
bits : 17 - 17 (1 bit)
access : read-write
STRSAMPLE : Enable Storing of Sensor Sample in Result Buffer
bits : 18 - 19 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
Nothing will be stored in the result buffer.
0x00000001 : DATA
The sensor sample data will be stored in the result buffer.
0x00000002 : DATASRC
The data source (i.e., the channel) will be stored alongside the sensor sample data.
End of enumeration elements list.
SCANRESINV : Enable Inversion of Result
bits : 20 - 20 (1 bit)
access : read-write
MODE : Configure Evaluation Mode
bits : 21 - 22 (2 bit)
access : read-write
Enumeration:
0x00000000 : THRES
Threshold comparison is used to evaluate sensor result
0x00000001 : SLIDINGWIN
Sliding window is used to evaluate sensor result
0x00000002 : STEPDET
Step detection is used to evaluate sensor result
End of enumeration elements list.
Scan Configuration
address_offset : 0x2F0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXTIME : Set Excitation Time
bits : 0 - 5 (6 bit)
access : read-write
SAMPLEDLY : Set Sample Delay
bits : 6 - 13 (8 bit)
access : read-write
MEASUREDLY : Set Measure Delay
bits : 14 - 23 (10 bit)
access : read-write
Scan Configuration
address_offset : 0x2F4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
THRES : ACMP Threshold or VDAC Data
bits : 0 - 11 (12 bit)
access : read-write
SAMPLE : Select Sample Mode
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
0x00000000 : ACMPCOUNT
Counter output will be used in evaluation
0x00000001 : ACMP
ACMP output will be used in evaluation
0x00000002 : ADC
ADC output will be used in evaluation
0x00000003 : ADCDIFF
Differential ADC output will be used in evaluation
End of enumeration elements list.
SETIF : Enable Interrupt Generation
bits : 14 - 16 (3 bit)
access : read-write
Enumeration:
0x00000000 : NONE
No interrupt is generated
0x00000001 : LEVEL
Set interrupt flag if the sensor triggers.
0x00000002 : POSEDGE
Set interrupt flag on positive edge of the sensor state
0x00000003 : NEGEDGE
Set interrupt flag on negative edge of the sensor state
0x00000004 : BOTHEDGES
Set interrupt flag on both edges of the sensor state
End of enumeration elements list.
EXMODE : Set GPIO Mode
bits : 17 - 18 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
Disabled
0x00000001 : HIGH
Push Pull, GPIO is driven high
0x00000002 : LOW
Push Pull, GPIO is driven low
0x00000003 : DACOUT
VDAC output
End of enumeration elements list.
EXCLK : Select Clock Used for Excitation Timing
bits : 19 - 19 (1 bit)
access : read-write
SAMPLECLK : Select Clock Used for Timing of Sample Delay
bits : 20 - 20 (1 bit)
access : read-write
ALTEX : Use Alternative Excite Pin
bits : 21 - 21 (1 bit)
access : read-write
Scan Configuration
address_offset : 0x2F8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMPTHRES : Decision Threshold for Sensor Data
bits : 0 - 15 (16 bit)
access : read-write
COMP : Select Mode for Threshold Comparison
bits : 16 - 16 (1 bit)
access : read-write
DECODE : Send Result to Decoder
bits : 17 - 17 (1 bit)
access : read-write
STRSAMPLE : Enable Storing of Sensor Sample in Result Buffer
bits : 18 - 19 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
Nothing will be stored in the result buffer.
0x00000001 : DATA
The sensor sample data will be stored in the result buffer.
0x00000002 : DATASRC
The data source (i.e., the channel) will be stored alongside the sensor sample data.
End of enumeration elements list.
SCANRESINV : Enable Inversion of Result
bits : 20 - 20 (1 bit)
access : read-write
MODE : Configure Evaluation Mode
bits : 21 - 22 (2 bit)
access : read-write
Enumeration:
0x00000000 : THRES
Threshold comparison is used to evaluate sensor result
0x00000001 : SLIDINGWIN
Sliding window is used to evaluate sensor result
0x00000002 : STEPDET
Step detection is used to evaluate sensor result
End of enumeration elements list.
Result Buffer Data Register
address_offset : 0x30 Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
BUFDATA : Result Data
bits : 0 - 15 (16 bit)
access : read-only
BUFDATASRC : Result Data Source
bits : 16 - 19 (4 bit)
access : read-only
Scan Configuration
address_offset : 0x300 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXTIME : Set Excitation Time
bits : 0 - 5 (6 bit)
access : read-write
SAMPLEDLY : Set Sample Delay
bits : 6 - 13 (8 bit)
access : read-write
MEASUREDLY : Set Measure Delay
bits : 14 - 23 (10 bit)
access : read-write
Scan Configuration
address_offset : 0x304 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
THRES : ACMP Threshold or VDAC Data
bits : 0 - 11 (12 bit)
access : read-write
SAMPLE : Select Sample Mode
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
0x00000000 : ACMPCOUNT
Counter output will be used in evaluation
0x00000001 : ACMP
ACMP output will be used in evaluation
0x00000002 : ADC
ADC output will be used in evaluation
0x00000003 : ADCDIFF
Differential ADC output will be used in evaluation
End of enumeration elements list.
SETIF : Enable Interrupt Generation
bits : 14 - 16 (3 bit)
access : read-write
Enumeration:
0x00000000 : NONE
No interrupt is generated
0x00000001 : LEVEL
Set interrupt flag if the sensor triggers.
0x00000002 : POSEDGE
Set interrupt flag on positive edge of the sensor state
0x00000003 : NEGEDGE
Set interrupt flag on negative edge of the sensor state
0x00000004 : BOTHEDGES
Set interrupt flag on both edges of the sensor state
End of enumeration elements list.
EXMODE : Set GPIO Mode
bits : 17 - 18 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
Disabled
0x00000001 : HIGH
Push Pull, GPIO is driven high
0x00000002 : LOW
Push Pull, GPIO is driven low
0x00000003 : DACOUT
VDAC output
End of enumeration elements list.
EXCLK : Select Clock Used for Excitation Timing
bits : 19 - 19 (1 bit)
access : read-write
SAMPLECLK : Select Clock Used for Timing of Sample Delay
bits : 20 - 20 (1 bit)
access : read-write
ALTEX : Use Alternative Excite Pin
bits : 21 - 21 (1 bit)
access : read-write
Scan Configuration
address_offset : 0x308 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMPTHRES : Decision Threshold for Sensor Data
bits : 0 - 15 (16 bit)
access : read-write
COMP : Select Mode for Threshold Comparison
bits : 16 - 16 (1 bit)
access : read-write
DECODE : Send Result to Decoder
bits : 17 - 17 (1 bit)
access : read-write
STRSAMPLE : Enable Storing of Sensor Sample in Result Buffer
bits : 18 - 19 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
Nothing will be stored in the result buffer.
0x00000001 : DATA
The sensor sample data will be stored in the result buffer.
0x00000002 : DATASRC
The data source (i.e., the channel) will be stored alongside the sensor sample data.
End of enumeration elements list.
SCANRESINV : Enable Inversion of Result
bits : 20 - 20 (1 bit)
access : read-write
MODE : Configure Evaluation Mode
bits : 21 - 22 (2 bit)
access : read-write
Enumeration:
0x00000000 : THRES
Threshold comparison is used to evaluate sensor result
0x00000001 : SLIDINGWIN
Sliding window is used to evaluate sensor result
0x00000002 : STEPDET
Step detection is used to evaluate sensor result
End of enumeration elements list.
Scan Configuration
address_offset : 0x310 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXTIME : Set Excitation Time
bits : 0 - 5 (6 bit)
access : read-write
SAMPLEDLY : Set Sample Delay
bits : 6 - 13 (8 bit)
access : read-write
MEASUREDLY : Set Measure Delay
bits : 14 - 23 (10 bit)
access : read-write
Scan Configuration
address_offset : 0x314 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
THRES : ACMP Threshold or VDAC Data
bits : 0 - 11 (12 bit)
access : read-write
SAMPLE : Select Sample Mode
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
0x00000000 : ACMPCOUNT
Counter output will be used in evaluation
0x00000001 : ACMP
ACMP output will be used in evaluation
0x00000002 : ADC
ADC output will be used in evaluation
0x00000003 : ADCDIFF
Differential ADC output will be used in evaluation
End of enumeration elements list.
SETIF : Enable Interrupt Generation
bits : 14 - 16 (3 bit)
access : read-write
Enumeration:
0x00000000 : NONE
No interrupt is generated
0x00000001 : LEVEL
Set interrupt flag if the sensor triggers.
0x00000002 : POSEDGE
Set interrupt flag on positive edge of the sensor state
0x00000003 : NEGEDGE
Set interrupt flag on negative edge of the sensor state
0x00000004 : BOTHEDGES
Set interrupt flag on both edges of the sensor state
End of enumeration elements list.
EXMODE : Set GPIO Mode
bits : 17 - 18 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
Disabled
0x00000001 : HIGH
Push Pull, GPIO is driven high
0x00000002 : LOW
Push Pull, GPIO is driven low
0x00000003 : DACOUT
VDAC output
End of enumeration elements list.
EXCLK : Select Clock Used for Excitation Timing
bits : 19 - 19 (1 bit)
access : read-write
SAMPLECLK : Select Clock Used for Timing of Sample Delay
bits : 20 - 20 (1 bit)
access : read-write
ALTEX : Use Alternative Excite Pin
bits : 21 - 21 (1 bit)
access : read-write
Scan Configuration
address_offset : 0x318 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMPTHRES : Decision Threshold for Sensor Data
bits : 0 - 15 (16 bit)
access : read-write
COMP : Select Mode for Threshold Comparison
bits : 16 - 16 (1 bit)
access : read-write
DECODE : Send Result to Decoder
bits : 17 - 17 (1 bit)
access : read-write
STRSAMPLE : Enable Storing of Sensor Sample in Result Buffer
bits : 18 - 19 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
Nothing will be stored in the result buffer.
0x00000001 : DATA
The sensor sample data will be stored in the result buffer.
0x00000002 : DATASRC
The data source (i.e., the channel) will be stored alongside the sensor sample data.
End of enumeration elements list.
SCANRESINV : Enable Inversion of Result
bits : 20 - 20 (1 bit)
access : read-write
MODE : Configure Evaluation Mode
bits : 21 - 22 (2 bit)
access : read-write
Enumeration:
0x00000000 : THRES
Threshold comparison is used to evaluate sensor result
0x00000001 : SLIDINGWIN
Sliding window is used to evaluate sensor result
0x00000002 : STEPDET
Step detection is used to evaluate sensor result
End of enumeration elements list.
Scan Configuration
address_offset : 0x320 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXTIME : Set Excitation Time
bits : 0 - 5 (6 bit)
access : read-write
SAMPLEDLY : Set Sample Delay
bits : 6 - 13 (8 bit)
access : read-write
MEASUREDLY : Set Measure Delay
bits : 14 - 23 (10 bit)
access : read-write
Scan Configuration
address_offset : 0x324 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
THRES : ACMP Threshold or VDAC Data
bits : 0 - 11 (12 bit)
access : read-write
SAMPLE : Select Sample Mode
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
0x00000000 : ACMPCOUNT
Counter output will be used in evaluation
0x00000001 : ACMP
ACMP output will be used in evaluation
0x00000002 : ADC
ADC output will be used in evaluation
0x00000003 : ADCDIFF
Differential ADC output will be used in evaluation
End of enumeration elements list.
SETIF : Enable Interrupt Generation
bits : 14 - 16 (3 bit)
access : read-write
Enumeration:
0x00000000 : NONE
No interrupt is generated
0x00000001 : LEVEL
Set interrupt flag if the sensor triggers.
0x00000002 : POSEDGE
Set interrupt flag on positive edge of the sensor state
0x00000003 : NEGEDGE
Set interrupt flag on negative edge of the sensor state
0x00000004 : BOTHEDGES
Set interrupt flag on both edges of the sensor state
End of enumeration elements list.
EXMODE : Set GPIO Mode
bits : 17 - 18 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
Disabled
0x00000001 : HIGH
Push Pull, GPIO is driven high
0x00000002 : LOW
Push Pull, GPIO is driven low
0x00000003 : DACOUT
VDAC output
End of enumeration elements list.
EXCLK : Select Clock Used for Excitation Timing
bits : 19 - 19 (1 bit)
access : read-write
SAMPLECLK : Select Clock Used for Timing of Sample Delay
bits : 20 - 20 (1 bit)
access : read-write
ALTEX : Use Alternative Excite Pin
bits : 21 - 21 (1 bit)
access : read-write
Scan Configuration
address_offset : 0x328 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMPTHRES : Decision Threshold for Sensor Data
bits : 0 - 15 (16 bit)
access : read-write
COMP : Select Mode for Threshold Comparison
bits : 16 - 16 (1 bit)
access : read-write
DECODE : Send Result to Decoder
bits : 17 - 17 (1 bit)
access : read-write
STRSAMPLE : Enable Storing of Sensor Sample in Result Buffer
bits : 18 - 19 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
Nothing will be stored in the result buffer.
0x00000001 : DATA
The sensor sample data will be stored in the result buffer.
0x00000002 : DATASRC
The data source (i.e., the channel) will be stored alongside the sensor sample data.
End of enumeration elements list.
SCANRESINV : Enable Inversion of Result
bits : 20 - 20 (1 bit)
access : read-write
MODE : Configure Evaluation Mode
bits : 21 - 22 (2 bit)
access : read-write
Enumeration:
0x00000000 : THRES
Threshold comparison is used to evaluate sensor result
0x00000001 : SLIDINGWIN
Sliding window is used to evaluate sensor result
0x00000002 : STEPDET
Step detection is used to evaluate sensor result
End of enumeration elements list.
Scan Configuration
address_offset : 0x330 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXTIME : Set Excitation Time
bits : 0 - 5 (6 bit)
access : read-write
SAMPLEDLY : Set Sample Delay
bits : 6 - 13 (8 bit)
access : read-write
MEASUREDLY : Set Measure Delay
bits : 14 - 23 (10 bit)
access : read-write
Scan Configuration
address_offset : 0x334 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
THRES : ACMP Threshold or VDAC Data
bits : 0 - 11 (12 bit)
access : read-write
SAMPLE : Select Sample Mode
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
0x00000000 : ACMPCOUNT
Counter output will be used in evaluation
0x00000001 : ACMP
ACMP output will be used in evaluation
0x00000002 : ADC
ADC output will be used in evaluation
0x00000003 : ADCDIFF
Differential ADC output will be used in evaluation
End of enumeration elements list.
SETIF : Enable Interrupt Generation
bits : 14 - 16 (3 bit)
access : read-write
Enumeration:
0x00000000 : NONE
No interrupt is generated
0x00000001 : LEVEL
Set interrupt flag if the sensor triggers.
0x00000002 : POSEDGE
Set interrupt flag on positive edge of the sensor state
0x00000003 : NEGEDGE
Set interrupt flag on negative edge of the sensor state
0x00000004 : BOTHEDGES
Set interrupt flag on both edges of the sensor state
End of enumeration elements list.
EXMODE : Set GPIO Mode
bits : 17 - 18 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
Disabled
0x00000001 : HIGH
Push Pull, GPIO is driven high
0x00000002 : LOW
Push Pull, GPIO is driven low
0x00000003 : DACOUT
VDAC output
End of enumeration elements list.
EXCLK : Select Clock Used for Excitation Timing
bits : 19 - 19 (1 bit)
access : read-write
SAMPLECLK : Select Clock Used for Timing of Sample Delay
bits : 20 - 20 (1 bit)
access : read-write
ALTEX : Use Alternative Excite Pin
bits : 21 - 21 (1 bit)
access : read-write
Scan Configuration
address_offset : 0x338 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMPTHRES : Decision Threshold for Sensor Data
bits : 0 - 15 (16 bit)
access : read-write
COMP : Select Mode for Threshold Comparison
bits : 16 - 16 (1 bit)
access : read-write
DECODE : Send Result to Decoder
bits : 17 - 17 (1 bit)
access : read-write
STRSAMPLE : Enable Storing of Sensor Sample in Result Buffer
bits : 18 - 19 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
Nothing will be stored in the result buffer.
0x00000001 : DATA
The sensor sample data will be stored in the result buffer.
0x00000002 : DATASRC
The data source (i.e., the channel) will be stored alongside the sensor sample data.
End of enumeration elements list.
SCANRESINV : Enable Inversion of Result
bits : 20 - 20 (1 bit)
access : read-write
MODE : Configure Evaluation Mode
bits : 21 - 22 (2 bit)
access : read-write
Enumeration:
0x00000000 : THRES
Threshold comparison is used to evaluate sensor result
0x00000001 : SLIDINGWIN
Sliding window is used to evaluate sensor result
0x00000002 : STEPDET
Step detection is used to evaluate sensor result
End of enumeration elements list.
Current Channel Index
address_offset : 0x34 Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
CURCH : Current Channel Index
bits : 0 - 3 (4 bit)
access : read-only
Current Decoder State
address_offset : 0x38 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DECSTATE : Current Decoder State
bits : 0 - 4 (5 bit)
access : read-write
Decoder Input Register
address_offset : 0x3C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
SENSORSTATE : Decoder Input Register
bits : 0 - 3 (4 bit)
access : read-write
Timing Control Register
address_offset : 0x4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
AUXPRESC : Prescaling Factor for High Frequency Timer
bits : 0 - 1 (2 bit)
access : read-write
Enumeration:
0x00000000 : DIV1
High frequency timer is clocked with AUXHFRCO/1
0x00000001 : DIV2
High frequency timer is clocked with AUXHFRCO/2
0x00000002 : DIV4
High frequency timer is clocked with AUXHFRCO/4
0x00000003 : DIV8
High frequency timer is clocked with AUXHFRCO/8
End of enumeration elements list.
LFPRESC : Prescaling Factor for Low Frequency Timer
bits : 4 - 6 (3 bit)
access : read-write
Enumeration:
0x00000000 : DIV1
Low frequency timer is clocked with LFACLKLESENSE/1
0x00000001 : DIV2
Low frequency timer is clocked with LFACLKLESENSE/2
0x00000002 : DIV4
Low frequency timer is clocked with LFACLKLESENSE/4
0x00000003 : DIV8
Low frequency timer is clocked with LFACLKLESENSE/8
0x00000004 : DIV16
Low frequency timer is clocked with LFACLKLESENSE/16
0x00000005 : DIV32
Low frequency timer is clocked with LFACLKLESENSE/32
0x00000006 : DIV64
Low frequency timer is clocked with LFACLKLESENSE/64
0x00000007 : DIV128
Low frequency timer is clocked with LFACLKLESENSE/128
End of enumeration elements list.
PCPRESC : Period Counter Prescaling
bits : 8 - 10 (3 bit)
access : read-write
Enumeration:
0x00000000 : DIV1
The period counter clock frequency is LFACLKLESENSE/1
0x00000001 : DIV2
The period counter clock frequency is LFACLKLESENSE/2
0x00000002 : DIV4
The period counter clock frequency is LFACLKLESENSE/4
0x00000003 : DIV8
The period counter clock frequency is LFACLKLESENSE/8
0x00000004 : DIV16
The period counter clock frequency is LFACLKLESENSE/16
0x00000005 : DIV32
The period counter clock frequency is LFACLKLESENSE/32
0x00000006 : DIV64
The period counter clock frequency is LFACLKLESENSE/64
0x00000007 : DIV128
The period counter clock frequency is LFACLKLESENSE/128
End of enumeration elements list.
PCTOP : Period Counter Top Value
bits : 12 - 19 (8 bit)
access : read-write
STARTDLY : Start Delay Configuration
bits : 22 - 23 (2 bit)
access : read-write
AUXSTARTUP : AUXHFRCO Startup Configuration
bits : 28 - 28 (1 bit)
access : read-write
GPIO Idle Phase Configuration
address_offset : 0x40 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
CH0 : Channel 0 Idle Phase Configuration
bits : 0 - 1 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
CH0 output is disabled in idle phase
0x00000001 : HIGH
CH0 output is high in idle phase
0x00000002 : LOW
CH0 output is low in idle phase
0x00000003 : DAC
CH0 output is connected to VDAC output in idle phase. Note that this mode is only available on channels
End of enumeration elements list.
CH1 : Channel 1 Idle Phase Configuration
bits : 2 - 3 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
CH1 output is disabled in idle phase
0x00000001 : HIGH
CH1 output is high in idle phase
0x00000002 : LOW
CH1 output is low in idle phase
0x00000003 : DAC
CH1 output is connected to VDAC output in idle phase. Note that this mode is only available on channels
End of enumeration elements list.
CH2 : Channel 2 Idle Phase Configuration
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
CH2 output is disabled in idle phase
0x00000001 : HIGH
CH2 output is high in idle phase
0x00000002 : LOW
CH2 output is low in idle phase
0x00000003 : DAC
CH2 output is connected to VDAC output in idle phase. Note that this mode is only available on channels
End of enumeration elements list.
CH3 : Channel 3 Idle Phase Configuration
bits : 6 - 7 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
CH3 output is disabled in idle phase
0x00000001 : HIGH
CH3 output is high in idle phase
0x00000002 : LOW
CH3 output is low in idle phase
0x00000003 : DAC
CH3 output is connected to VDAC output in idle phase. Note that this mode is only available on channels
End of enumeration elements list.
CH4 : Channel 4 Idle Phase Configuration
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
CH4 output is disabled in idle phase
0x00000001 : HIGH
CH4 output is high in idle phase
0x00000002 : LOW
CH4 output is low in idle phase
0x00000003 : DAC
CH4 output is connected to VDAC output in idle phase. Note that this mode is only available on channels
End of enumeration elements list.
CH5 : Channel 5 Idle Phase Configuration
bits : 10 - 11 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
CH5 output is disabled in idle phase
0x00000001 : HIGH
CH5 output is high in idle phase
0x00000002 : LOW
CH5 output is low in idle phase
0x00000003 : DAC
CH5 output is connected to VDAC output in idle phase. Note that this mode is only available on channels
End of enumeration elements list.
CH6 : Channel 6 Idle Phase Configuration
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
CH6 output is disabled in idle phase
0x00000001 : HIGH
CH6 output is high in idle phase
0x00000002 : LOW
CH6 output is low in idle phase
0x00000003 : DAC
CH6 output is connected to VDAC output in idle phase. Note that this mode is only available on channels
End of enumeration elements list.
CH7 : Channel 7 Idle Phase Configuration
bits : 14 - 15 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
CH7 output is disabled in idle phase
0x00000001 : HIGH
CH7 output is high in idle phase
0x00000002 : LOW
CH7 output is low in idle phase
0x00000003 : DAC
CH7 output is connected to VDAC output in idle phase. Note that this mode is only available on channels
End of enumeration elements list.
CH8 : Channel 8 Idle Phase Configuration
bits : 16 - 17 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
CH8 output is disabled in idle phase
0x00000001 : HIGH
CH8 output is high in idle phase
0x00000002 : LOW
CH8 output is low in idle phase
0x00000003 : DAC
CH8 output is connected to VDAC output in idle phase. Note that this mode is only available on channels
End of enumeration elements list.
CH9 : Channel 9 Idle Phase Configuration
bits : 18 - 19 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
CH9 output is disabled in idle phase
0x00000001 : HIGH
CH9 output is high in idle phase
0x00000002 : LOW
CH9 output is low in idle phase
0x00000003 : DAC
CH9 output is connected to VDAC output in idle phase. Note that this mode is only available on channels
End of enumeration elements list.
CH10 : Channel 10 Idle Phase Configuration
bits : 20 - 21 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
CH10 output is disabled in idle phase
0x00000001 : HIGH
CH10 output is high in idle phase
0x00000002 : LOW
CH10 output is low in idle phase
0x00000003 : DAC
CH10 output is connected to VDAC output in idle phase. Note that this mode is only available on channels
End of enumeration elements list.
CH11 : Channel 11 Idle Phase Configuration
bits : 22 - 23 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
CH11 output is disabled in idle phase
0x00000001 : HIGH
CH11 output is high in idle phase
0x00000002 : LOW
CH11 output is low in idle phase
0x00000003 : DAC
CH11 output is connected to VDAC output in idle phase. Note that this mode is only available on channels
End of enumeration elements list.
CH12 : Channel 12 Idle Phase Configuration
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
CH12 output is disabled in idle phase
0x00000001 : HIGH
CH12 output is high in idle phase
0x00000002 : LOW
CH12 output is low in idle phase
0x00000003 : DAC
CH12 output is connected to VDAC output in idle phase. Note that this mode is only available on channels
End of enumeration elements list.
CH13 : Channel 13 Idle Phase Configuration
bits : 26 - 27 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
CH13 output is disabled in idle phase
0x00000001 : HIGH
CH13 output is high in idle phase
0x00000002 : LOW
CH13 output is low in idle phase
0x00000003 : DAC
CH13 output is connected to VDAC output in idle phase. Note that this mode is only available on channels
End of enumeration elements list.
CH14 : Channel 14 Idle Phase Configuration
bits : 28 - 29 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
CH14 output is disabled in idle phase
0x00000001 : HIGH
CH14 output is high in idle phase
0x00000002 : LOW
CH14 output is low in idle phase
0x00000003 : DAC
CH14 output is connected to VDAC output in idle phase. Note that this mode is only available on channels
End of enumeration elements list.
CH15 : Channel 15 Idle Phase Configuration
bits : 30 - 31 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
CH15 output is disabled in idle phase
0x00000001 : HIGH
CH15 output is high in idle phase
0x00000002 : LOW
CH15 output is low in idle phase
0x00000003 : DAC
CH15 output is connected to VDAC output in idle phase. Note that this mode is only available on channels
End of enumeration elements list.
Alternative Excite Pin Configuration
address_offset : 0x44 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
IDLECONF0 : ALTEX0 Idle Phase Configuration
bits : 0 - 1 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
ALTEX0 output is disabled in idle phase
0x00000001 : HIGH
ALTEX0 output is high in idle phase
0x00000002 : LOW
ALTEX0 output is low in idle phase
End of enumeration elements list.
IDLECONF1 : ALTEX1 Idle Phase Configuration
bits : 2 - 3 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
ALTEX1 output is disabled in idle phase
0x00000001 : HIGH
ALTEX1 output is high in idle phase
0x00000002 : LOW
ALTEX1 output is low in idle phase
End of enumeration elements list.
IDLECONF2 : ALTEX2 Idle Phase Configuration
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
ALTEX2 output is disabled in idle phase
0x00000001 : HIGH
ALTEX2 output is high in idle phase
0x00000002 : LOW
ALTEX2 output is low in idle phase
End of enumeration elements list.
IDLECONF3 : ALTEX3 Idle Phase Configuration
bits : 6 - 7 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
ALTEX3 output is disabled in idle phase
0x00000001 : HIGH
ALTEX3 output is high in idle phase
0x00000002 : LOW
ALTEX3 output is low in idle phase
End of enumeration elements list.
IDLECONF4 : ALTEX4 Idle Phase Configuration
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
ALTEX4 output is disabled in idle phase
0x00000001 : HIGH
ALTEX4 output is high in idle phase
0x00000002 : LOW
ALTEX4 output is low in idle phase
End of enumeration elements list.
IDLECONF5 : ALTEX5 Idle Phase Configuration
bits : 10 - 11 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
ALTEX5 output is disabled in idle phase
0x00000001 : HIGH
ALTEX5 output is high in idle phase
0x00000002 : LOW
ALTEX5 output is low in idle phase
End of enumeration elements list.
IDLECONF6 : ALTEX6 Idle Phase Configuration
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
ALTEX6 output is disabled in idle phase
0x00000001 : HIGH
ALTEX6 output is high in idle phase
0x00000002 : LOW
ALTEX6 output is low in idle phase
End of enumeration elements list.
IDLECONF7 : ALTEX7 Idle Phase Configuration
bits : 14 - 15 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
ALTEX7 output is disabled in idle phase
0x00000001 : HIGH
ALTEX7 output is high in idle phase
0x00000002 : LOW
ALTEX7 output is low in idle phase
End of enumeration elements list.
AEX0 : ALTEX0 Always Excite Enable
bits : 16 - 16 (1 bit)
access : read-write
AEX1 : ALTEX1 Always Excite Enable
bits : 17 - 17 (1 bit)
access : read-write
AEX2 : ALTEX2 Always Excite Enable
bits : 18 - 18 (1 bit)
access : read-write
AEX3 : ALTEX3 Always Excite Enable
bits : 19 - 19 (1 bit)
access : read-write
AEX4 : ALTEX4 Always Excite Enable
bits : 20 - 20 (1 bit)
access : read-write
AEX5 : ALTEX5 Always Excite Enable
bits : 21 - 21 (1 bit)
access : read-write
AEX6 : ALTEX6 Always Excite Enable
bits : 22 - 22 (1 bit)
access : read-write
AEX7 : ALTEX7 Always Excite Enable
bits : 23 - 23 (1 bit)
access : read-write
Interrupt Flag Register
address_offset : 0x50 Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
CH0 : CH0 Interrupt Flag
bits : 0 - 0 (1 bit)
access : read-only
CH1 : CH1 Interrupt Flag
bits : 1 - 1 (1 bit)
access : read-only
CH2 : CH2 Interrupt Flag
bits : 2 - 2 (1 bit)
access : read-only
CH3 : CH3 Interrupt Flag
bits : 3 - 3 (1 bit)
access : read-only
CH4 : CH4 Interrupt Flag
bits : 4 - 4 (1 bit)
access : read-only
CH5 : CH5 Interrupt Flag
bits : 5 - 5 (1 bit)
access : read-only
CH6 : CH6 Interrupt Flag
bits : 6 - 6 (1 bit)
access : read-only
CH7 : CH7 Interrupt Flag
bits : 7 - 7 (1 bit)
access : read-only
CH8 : CH8 Interrupt Flag
bits : 8 - 8 (1 bit)
access : read-only
CH9 : CH9 Interrupt Flag
bits : 9 - 9 (1 bit)
access : read-only
CH10 : CH10 Interrupt Flag
bits : 10 - 10 (1 bit)
access : read-only
CH11 : CH11 Interrupt Flag
bits : 11 - 11 (1 bit)
access : read-only
CH12 : CH12 Interrupt Flag
bits : 12 - 12 (1 bit)
access : read-only
CH13 : CH13 Interrupt Flag
bits : 13 - 13 (1 bit)
access : read-only
CH14 : CH14 Interrupt Flag
bits : 14 - 14 (1 bit)
access : read-only
CH15 : CH15 Interrupt Flag
bits : 15 - 15 (1 bit)
access : read-only
SCANCOMPLETE : SCANCOMPLETE Interrupt Flag
bits : 16 - 16 (1 bit)
access : read-only
DEC : DEC Interrupt Flag
bits : 17 - 17 (1 bit)
access : read-only
DECERR : DECERR Interrupt Flag
bits : 18 - 18 (1 bit)
access : read-only
BUFDATAV : BUFDATAV Interrupt Flag
bits : 19 - 19 (1 bit)
access : read-only
BUFLEVEL : BUFLEVEL Interrupt Flag
bits : 20 - 20 (1 bit)
access : read-only
BUFOF : BUFOF Interrupt Flag
bits : 21 - 21 (1 bit)
access : read-only
CNTOF : CNTOF Interrupt Flag
bits : 22 - 22 (1 bit)
access : read-only
Interrupt Flag Set Register
address_offset : 0x54 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
CH0 : Set CH0 Interrupt Flag
bits : 0 - 0 (1 bit)
access : write-only
CH1 : Set CH1 Interrupt Flag
bits : 1 - 1 (1 bit)
access : write-only
CH2 : Set CH2 Interrupt Flag
bits : 2 - 2 (1 bit)
access : write-only
CH3 : Set CH3 Interrupt Flag
bits : 3 - 3 (1 bit)
access : write-only
CH4 : Set CH4 Interrupt Flag
bits : 4 - 4 (1 bit)
access : write-only
CH5 : Set CH5 Interrupt Flag
bits : 5 - 5 (1 bit)
access : write-only
CH6 : Set CH6 Interrupt Flag
bits : 6 - 6 (1 bit)
access : write-only
CH7 : Set CH7 Interrupt Flag
bits : 7 - 7 (1 bit)
access : write-only
CH8 : Set CH8 Interrupt Flag
bits : 8 - 8 (1 bit)
access : write-only
CH9 : Set CH9 Interrupt Flag
bits : 9 - 9 (1 bit)
access : write-only
CH10 : Set CH10 Interrupt Flag
bits : 10 - 10 (1 bit)
access : write-only
CH11 : Set CH11 Interrupt Flag
bits : 11 - 11 (1 bit)
access : write-only
CH12 : Set CH12 Interrupt Flag
bits : 12 - 12 (1 bit)
access : write-only
CH13 : Set CH13 Interrupt Flag
bits : 13 - 13 (1 bit)
access : write-only
CH14 : Set CH14 Interrupt Flag
bits : 14 - 14 (1 bit)
access : write-only
CH15 : Set CH15 Interrupt Flag
bits : 15 - 15 (1 bit)
access : write-only
SCANCOMPLETE : Set SCANCOMPLETE Interrupt Flag
bits : 16 - 16 (1 bit)
access : write-only
DEC : Set DEC Interrupt Flag
bits : 17 - 17 (1 bit)
access : write-only
DECERR : Set DECERR Interrupt Flag
bits : 18 - 18 (1 bit)
access : write-only
BUFDATAV : Set BUFDATAV Interrupt Flag
bits : 19 - 19 (1 bit)
access : write-only
BUFLEVEL : Set BUFLEVEL Interrupt Flag
bits : 20 - 20 (1 bit)
access : write-only
BUFOF : Set BUFOF Interrupt Flag
bits : 21 - 21 (1 bit)
access : write-only
CNTOF : Set CNTOF Interrupt Flag
bits : 22 - 22 (1 bit)
access : write-only
Interrupt Flag Clear Register
address_offset : 0x58 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
CH0 : Clear CH0 Interrupt Flag
bits : 0 - 0 (1 bit)
access : write-only
CH1 : Clear CH1 Interrupt Flag
bits : 1 - 1 (1 bit)
access : write-only
CH2 : Clear CH2 Interrupt Flag
bits : 2 - 2 (1 bit)
access : write-only
CH3 : Clear CH3 Interrupt Flag
bits : 3 - 3 (1 bit)
access : write-only
CH4 : Clear CH4 Interrupt Flag
bits : 4 - 4 (1 bit)
access : write-only
CH5 : Clear CH5 Interrupt Flag
bits : 5 - 5 (1 bit)
access : write-only
CH6 : Clear CH6 Interrupt Flag
bits : 6 - 6 (1 bit)
access : write-only
CH7 : Clear CH7 Interrupt Flag
bits : 7 - 7 (1 bit)
access : write-only
CH8 : Clear CH8 Interrupt Flag
bits : 8 - 8 (1 bit)
access : write-only
CH9 : Clear CH9 Interrupt Flag
bits : 9 - 9 (1 bit)
access : write-only
CH10 : Clear CH10 Interrupt Flag
bits : 10 - 10 (1 bit)
access : write-only
CH11 : Clear CH11 Interrupt Flag
bits : 11 - 11 (1 bit)
access : write-only
CH12 : Clear CH12 Interrupt Flag
bits : 12 - 12 (1 bit)
access : write-only
CH13 : Clear CH13 Interrupt Flag
bits : 13 - 13 (1 bit)
access : write-only
CH14 : Clear CH14 Interrupt Flag
bits : 14 - 14 (1 bit)
access : write-only
CH15 : Clear CH15 Interrupt Flag
bits : 15 - 15 (1 bit)
access : write-only
SCANCOMPLETE : Clear SCANCOMPLETE Interrupt Flag
bits : 16 - 16 (1 bit)
access : write-only
DEC : Clear DEC Interrupt Flag
bits : 17 - 17 (1 bit)
access : write-only
DECERR : Clear DECERR Interrupt Flag
bits : 18 - 18 (1 bit)
access : write-only
BUFDATAV : Clear BUFDATAV Interrupt Flag
bits : 19 - 19 (1 bit)
access : write-only
BUFLEVEL : Clear BUFLEVEL Interrupt Flag
bits : 20 - 20 (1 bit)
access : write-only
BUFOF : Clear BUFOF Interrupt Flag
bits : 21 - 21 (1 bit)
access : write-only
CNTOF : Clear CNTOF Interrupt Flag
bits : 22 - 22 (1 bit)
access : write-only
Interrupt Enable Register
address_offset : 0x5C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
CH0 : CH0 Interrupt Enable
bits : 0 - 0 (1 bit)
access : read-write
CH1 : CH1 Interrupt Enable
bits : 1 - 1 (1 bit)
access : read-write
CH2 : CH2 Interrupt Enable
bits : 2 - 2 (1 bit)
access : read-write
CH3 : CH3 Interrupt Enable
bits : 3 - 3 (1 bit)
access : read-write
CH4 : CH4 Interrupt Enable
bits : 4 - 4 (1 bit)
access : read-write
CH5 : CH5 Interrupt Enable
bits : 5 - 5 (1 bit)
access : read-write
CH6 : CH6 Interrupt Enable
bits : 6 - 6 (1 bit)
access : read-write
CH7 : CH7 Interrupt Enable
bits : 7 - 7 (1 bit)
access : read-write
CH8 : CH8 Interrupt Enable
bits : 8 - 8 (1 bit)
access : read-write
CH9 : CH9 Interrupt Enable
bits : 9 - 9 (1 bit)
access : read-write
CH10 : CH10 Interrupt Enable
bits : 10 - 10 (1 bit)
access : read-write
CH11 : CH11 Interrupt Enable
bits : 11 - 11 (1 bit)
access : read-write
CH12 : CH12 Interrupt Enable
bits : 12 - 12 (1 bit)
access : read-write
CH13 : CH13 Interrupt Enable
bits : 13 - 13 (1 bit)
access : read-write
CH14 : CH14 Interrupt Enable
bits : 14 - 14 (1 bit)
access : read-write
CH15 : CH15 Interrupt Enable
bits : 15 - 15 (1 bit)
access : read-write
SCANCOMPLETE : SCANCOMPLETE Interrupt Enable
bits : 16 - 16 (1 bit)
access : read-write
DEC : DEC Interrupt Enable
bits : 17 - 17 (1 bit)
access : read-write
DECERR : DECERR Interrupt Enable
bits : 18 - 18 (1 bit)
access : read-write
BUFDATAV : BUFDATAV Interrupt Enable
bits : 19 - 19 (1 bit)
access : read-write
BUFLEVEL : BUFLEVEL Interrupt Enable
bits : 20 - 20 (1 bit)
access : read-write
BUFOF : BUFOF Interrupt Enable
bits : 21 - 21 (1 bit)
access : read-write
CNTOF : CNTOF Interrupt Enable
bits : 22 - 22 (1 bit)
access : read-write
Synchronization Busy Register
address_offset : 0x60 Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
CMD : CMD Register Busy
bits : 7 - 7 (1 bit)
access : read-only
I/O Routing Register
address_offset : 0x64 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
CH0PEN : CH0 Pin Enable
bits : 0 - 0 (1 bit)
access : read-write
CH1PEN : CH1 Pin Enable
bits : 1 - 1 (1 bit)
access : read-write
CH2PEN : CH2 Pin Enable
bits : 2 - 2 (1 bit)
access : read-write
CH3PEN : CH3 Pin Enable
bits : 3 - 3 (1 bit)
access : read-write
CH4PEN : CH4 Pin Enable
bits : 4 - 4 (1 bit)
access : read-write
CH5PEN : CH5 Pin Enable
bits : 5 - 5 (1 bit)
access : read-write
CH6PEN : CH6 Pin Enable
bits : 6 - 6 (1 bit)
access : read-write
CH7PEN : CH7 Pin Enable
bits : 7 - 7 (1 bit)
access : read-write
CH8PEN : CH8 Pin Enable
bits : 8 - 8 (1 bit)
access : read-write
CH9PEN : CH9 Pin Enable
bits : 9 - 9 (1 bit)
access : read-write
CH10PEN : CH10 Pin Enable
bits : 10 - 10 (1 bit)
access : read-write
CH11PEN : CH11 Pin Enable
bits : 11 - 11 (1 bit)
access : read-write
CH12PEN : CH12 Pin Enable
bits : 12 - 12 (1 bit)
access : read-write
CH13PEN : CH13 Pin Enable
bits : 13 - 13 (1 bit)
access : read-write
CH14PEN : CH14 Pin Enable
bits : 14 - 14 (1 bit)
access : read-write
CH15PEN : CH15 Pin Enable
bits : 15 - 15 (1 bit)
access : read-write
ALTEX0PEN : ALTEX0 Pin Enable
bits : 16 - 16 (1 bit)
access : read-write
ALTEX1PEN : ALTEX1 Pin Enable
bits : 17 - 17 (1 bit)
access : read-write
ALTEX2PEN : ALTEX2 Pin Enable
bits : 18 - 18 (1 bit)
access : read-write
ALTEX3PEN : ALTEX3 Pin Enable
bits : 19 - 19 (1 bit)
access : read-write
ALTEX4PEN : ALTEX4 Pin Enable
bits : 20 - 20 (1 bit)
access : read-write
ALTEX5PEN : ALTEX5 Pin Enable
bits : 21 - 21 (1 bit)
access : read-write
ALTEX6PEN : ALTEX6 Pin Enable
bits : 22 - 22 (1 bit)
access : read-write
ALTEX7PEN : ALTEX7 Pin Enable
bits : 23 - 23 (1 bit)
access : read-write
Peripheral Control Register
address_offset : 0x8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DACCH0EN : VDAC CH0 Enable
bits : 0 - 0 (1 bit)
access : read-write
DACCH1EN : VDAC CH1 Enable
bits : 1 - 1 (1 bit)
access : read-write
DACCH0DATA : VDAC CH0 Data Selection
bits : 2 - 2 (1 bit)
access : read-write
DACCH1DATA : VDAC CH1 Data Selection
bits : 3 - 3 (1 bit)
access : read-write
DACSTARTUP : VDAC Startup Configuration
bits : 6 - 6 (1 bit)
access : read-write
DACCONVTRIG : VDAC Conversion Trigger Configuration
bits : 8 - 8 (1 bit)
access : read-write
ACMP0MODE : ACMP0 Mode
bits : 20 - 21 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
LESENSE does not control ACMP0
0x00000001 : MUX
LESENSE controls the input mux (POSSEL) of ACMP0
0x00000002 : MUXTHRES
LESENSE controls the input mux (POSSEL) and the threshold value (VDDLEVEL) of ACMP0
End of enumeration elements list.
ACMP1MODE : ACMP1 Mode
bits : 22 - 23 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
LESENSE does not control ACMP1
0x00000001 : MUX
LESENSE controls the input mux (POSSEL) of ACMP1
0x00000002 : MUXTHRES
LESENSE controls the input mux and the threshold value (VDDLEVEL) of ACMP1
End of enumeration elements list.
ACMP0INV : Invert Analog Comparator 0 Output
bits : 24 - 24 (1 bit)
access : read-write
ACMP1INV : Invert Analog Comparator 1 Output
bits : 25 - 25 (1 bit)
access : read-write
ACMP0HYSTEN : ACMP0 Hysteresis Enable
bits : 26 - 26 (1 bit)
access : read-write
ACMP1HYSTEN : ACMP1 Hysteresis Enable
bits : 27 - 27 (1 bit)
access : read-write
WARMUPMODE : ACMP and VDAC Duty Cycle Mode
bits : 28 - 29 (2 bit)
access : read-write
Enumeration:
0x00000000 : NORMAL
The analog comparators and VDAC are shut down when LESENSE is idle
0x00000001 : KEEPACMPWARM
The analog comparators are kept powered up when LESENSE is idle
0x00000002 : KEEPDACWARM
The VDAC is kept powered up when LESENSE is idle
0x00000003 : KEEPACMPDACWARM
The analog comparators and VDAC are kept powered up when LESENSE is idle
End of enumeration elements list.
Decoder Control Register
address_offset : 0xC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DISABLE : Disable the Decoder
bits : 0 - 0 (1 bit)
access : read-write
ERRCHK : Enable Check of Current State
bits : 1 - 1 (1 bit)
access : read-write
INTMAP : Enable Decoder to Channel Interrupt Mapping
bits : 2 - 2 (1 bit)
access : read-write
HYSTPRS0 : Enable Decoder Hysteresis on PRS0 Output
bits : 3 - 3 (1 bit)
access : read-write
HYSTPRS1 : Enable Decoder Hysteresis on PRS1 Output
bits : 4 - 4 (1 bit)
access : read-write
HYSTPRS2 : Enable Decoder Hysteresis on PRS2 Output
bits : 5 - 5 (1 bit)
access : read-write
HYSTIRQ : Enable Decoder Hysteresis on Interrupt Requests
bits : 6 - 6 (1 bit)
access : read-write
PRSCNT : Enable Count Mode on Decoder PRS Channels 0 and 1
bits : 7 - 7 (1 bit)
access : read-write
INPUT : LESENSE Decoder Input Configuration
bits : 8 - 8 (1 bit)
access : read-write
PRSSEL0 : LESENSE Decoder PRS Input 0 Configuration
bits : 10 - 13 (4 bit)
access : read-write
Enumeration:
0x00000000 : PRSCH0
PRS Channel 0 selected as input
0x00000001 : PRSCH1
PRS Channel 1 selected as input
0x00000002 : PRSCH2
PRS Channel 2 selected as input
0x00000003 : PRSCH3
PRS Channel 3 selected as input
0x00000004 : PRSCH4
PRS Channel 4 selected as input
0x00000005 : PRSCH5
PRS Channel 5 selected as input
0x00000006 : PRSCH6
PRS Channel 6 selected as input
0x00000007 : PRSCH7
PRS Channel 7 selected as input
0x00000008 : PRSCH8
PRS Channel 8 selected as input
0x00000009 : PRSCH9
PRS Channel 9 selected as input
0x0000000A : PRSCH10
PRS Channel 10 selected as input
0x0000000B : PRSCH11
PRS Channel 11 selected as input
End of enumeration elements list.
PRSSEL1 : LESENSE Decoder PRS Input 1 Configuration
bits : 15 - 18 (4 bit)
access : read-write
Enumeration:
0x00000000 : PRSCH0
PRS Channel 0 selected as input
0x00000001 : PRSCH1
PRS Channel 1 selected as input
0x00000002 : PRSCH2
PRS Channel 2 selected as input
0x00000003 : PRSCH3
PRS Channel 3 selected as input
0x00000004 : PRSCH4
PRS Channel 4 selected as input
0x00000005 : PRSCH5
PRS Channel 5 selected as input
0x00000006 : PRSCH6
PRS Channel 6 selected as input
0x00000007 : PRSCH7
PRS Channel 7 selected as input
0x00000008 : PRSCH8
PRS Channel 8 selected as input
0x00000009 : PRSCH9
PRS Channel 9 selected as input
0x0000000A : PRSCH10
PRS Channel 10 selected as input
0x0000000B : PRSCH11
PRS Channel 11 selected as input
End of enumeration elements list.
PRSSEL2 : LESENSE Decoder PRS Input 2 Configuration
bits : 20 - 23 (4 bit)
access : read-write
Enumeration:
0x00000000 : PRSCH0
PRS Channel 0 selected as input
0x00000001 : PRSCH1
PRS Channel 1 selected as input
0x00000002 : PRSCH2
PRS Channel 2 selected as input
0x00000003 : PRSCH3
PRS Channel 3 selected as input
0x00000004 : PRSCH4
PRS Channel 4 selected as input
0x00000005 : PRSCH5
PRS Channel 5 selected as input
0x00000006 : PRSCH6
PRS Channel 6 selected as input
0x00000007 : PRSCH7
PRS Channel 7 selected as input
0x00000008 : PRSCH8
PRS Channel 8 selected as input
0x00000009 : PRSCH9
PRS Channel 9 selected as input
0x0000000A : PRSCH10
PRS Channel 10 selected as input
0x0000000B : PRSCH11
PRS Channel 11 selected as input
End of enumeration elements list.
PRSSEL3 : LESENSE Decoder PRS Input 3 Configuration
bits : 25 - 28 (4 bit)
access : read-write
Enumeration:
0x00000000 : PRSCH0
PRS Channel 0 selected as input
0x00000001 : PRSCH1
PRS Channel 1 selected as input
0x00000002 : PRSCH2
PRS Channel 2 selected as input
0x00000003 : PRSCH3
PRS Channel 3 selected as input
0x00000004 : PRSCH4
PRS Channel 4 selected as input
0x00000005 : PRSCH5
PRS Channel 5 selected as input
0x00000006 : PRSCH6
PRS Channel 6 selected as input
0x00000007 : PRSCH7
PRS Channel 7 selected as input
0x00000008 : PRSCH8
PRS Channel 8 selected as input
0x00000009 : PRSCH9
PRS Channel 9 selected as input
0x0000000A : PRSCH10
PRS Channel 10 selected as input
0x0000000B : PRSCH11
PRS Channel 11 selected as input
End of enumeration elements list.
Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !
This website is sponsored by Embeetle, an IDE designed from scratch for embedded software developers.