\n
address_offset : 0x0 Bytes (0x0)
size : 0x50 byte (0x0)
mem_usage : registers
protection : not protected
Control Register
address_offset : 0x0 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
START : Send a START Condition
bits : 0 - 0 (1 bit)
access : write-only
STOP : Send a STOP Condition
bits : 1 - 1 (1 bit)
access : write-only
MSEN : TWI Master Mode Enabled
bits : 2 - 2 (1 bit)
access : write-only
MSDIS : TWI Master Mode Disabled
bits : 3 - 3 (1 bit)
access : write-only
SVEN : TWI Slave Mode Enabled
bits : 4 - 4 (1 bit)
access : write-only
SVDIS : TWI Slave Mode Disabled
bits : 5 - 5 (1 bit)
access : write-only
QUICK : SMBUS Quick Command
bits : 6 - 6 (1 bit)
access : write-only
SWRST : Software Reset
bits : 7 - 7 (1 bit)
access : write-only
Clock Waveform Generator Register
address_offset : 0x10 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
CLDIV : Clock Low Divider
bits : 0 - 7 (8 bit)
access : read-write
CHDIV : Clock High Divider
bits : 8 - 15 (8 bit)
access : read-write
CKDIV : Clock Divider
bits : 16 - 18 (3 bit)
access : read-write
Receive Pointer Register
address_offset : 0x100 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RXPTR : Receive Pointer Register
bits : 0 - 31 (32 bit)
access : read-write
Receive Counter Register
address_offset : 0x104 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RXCTR : Receive Counter Register
bits : 0 - 15 (16 bit)
access : read-write
Transmit Pointer Register
address_offset : 0x108 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TXPTR : Transmit Counter Register
bits : 0 - 31 (32 bit)
access : read-write
Transmit Counter Register
address_offset : 0x10C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TXCTR : Transmit Counter Register
bits : 0 - 15 (16 bit)
access : read-write
Receive Next Pointer Register
address_offset : 0x110 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RXNPTR : Receive Next Pointer
bits : 0 - 31 (32 bit)
access : read-write
Receive Next Counter Register
address_offset : 0x114 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RXNCTR : Receive Next Counter
bits : 0 - 15 (16 bit)
access : read-write
Transmit Next Pointer Register
address_offset : 0x118 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TXNPTR : Transmit Next Pointer
bits : 0 - 31 (32 bit)
access : read-write
Transmit Next Counter Register
address_offset : 0x11C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TXNCTR : Transmit Counter Next
bits : 0 - 15 (16 bit)
access : read-write
Transfer Control Register
address_offset : 0x120 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
RXTEN : Receiver Transfer Enable
bits : 0 - 0 (1 bit)
access : write-only
RXTDIS : Receiver Transfer Disable
bits : 1 - 1 (1 bit)
access : write-only
TXTEN : Transmitter Transfer Enable
bits : 8 - 8 (1 bit)
access : write-only
TXTDIS : Transmitter Transfer Disable
bits : 9 - 9 (1 bit)
access : write-only
Transfer Status Register
address_offset : 0x124 Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
RXTEN : Receiver Transfer Enable
bits : 0 - 0 (1 bit)
access : read-only
TXTEN : Transmitter Transfer Enable
bits : 8 - 8 (1 bit)
access : read-only
Status Register
address_offset : 0x20 Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
TXCOMP : Transmission Completed (automatically set / reset)
bits : 0 - 0 (1 bit)
access : read-only
RXRDY : Receive Holding Register Ready (automatically set / reset)
bits : 1 - 1 (1 bit)
access : read-only
TXRDY : Transmit Holding Register Ready (automatically set / reset)
bits : 2 - 2 (1 bit)
access : read-only
SVREAD : Slave Read (automatically set / reset)
bits : 3 - 3 (1 bit)
access : read-only
SVACC : Slave Access (automatically set / reset)
bits : 4 - 4 (1 bit)
access : read-only
GACC : General Call Access (clear on read)
bits : 5 - 5 (1 bit)
access : read-only
OVRE : Overrun Error (clear on read)
bits : 6 - 6 (1 bit)
access : read-only
NACK : Not Acknowledged (clear on read)
bits : 8 - 8 (1 bit)
access : read-only
ARBLST : Arbitration Lost (clear on read)
bits : 9 - 9 (1 bit)
access : read-only
SCLWS : Clock Wait State (automatically set / reset)
bits : 10 - 10 (1 bit)
access : read-only
EOSACC : End Of Slave Access (clear on read)
bits : 11 - 11 (1 bit)
access : read-only
ENDRX : End of RX buffer
bits : 12 - 12 (1 bit)
access : read-only
ENDTX : End of TX buffer
bits : 13 - 13 (1 bit)
access : read-only
RXBUFF : RX Buffer Full
bits : 14 - 14 (1 bit)
access : read-only
TXBUFE : TX Buffer Empty
bits : 15 - 15 (1 bit)
access : read-only
Interrupt Enable Register
address_offset : 0x24 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
TXCOMP : Transmission Completed Interrupt Enable
bits : 0 - 0 (1 bit)
access : write-only
RXRDY : Receive Holding Register Ready Interrupt Enable
bits : 1 - 1 (1 bit)
access : write-only
TXRDY : Transmit Holding Register Ready Interrupt Enable
bits : 2 - 2 (1 bit)
access : write-only
SVACC : Slave Access Interrupt Enable
bits : 4 - 4 (1 bit)
access : write-only
GACC : General Call Access Interrupt Enable
bits : 5 - 5 (1 bit)
access : write-only
OVRE : Overrun Error Interrupt Enable
bits : 6 - 6 (1 bit)
access : write-only
NACK : Not Acknowledge Interrupt Enable
bits : 8 - 8 (1 bit)
access : write-only
ARBLST : Arbitration Lost Interrupt Enable
bits : 9 - 9 (1 bit)
access : write-only
SCL_WS : Clock Wait State Interrupt Enable
bits : 10 - 10 (1 bit)
access : write-only
EOSACC : End Of Slave Access Interrupt Enable
bits : 11 - 11 (1 bit)
access : write-only
ENDRX : End of Receive Buffer Interrupt Enable
bits : 12 - 12 (1 bit)
access : write-only
ENDTX : End of Transmit Buffer Interrupt Enable
bits : 13 - 13 (1 bit)
access : write-only
RXBUFF : Receive Buffer Full Interrupt Enable
bits : 14 - 14 (1 bit)
access : write-only
TXBUFE : Transmit Buffer Empty Interrupt Enable
bits : 15 - 15 (1 bit)
access : write-only
Interrupt Disable Register
address_offset : 0x28 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
TXCOMP : Transmission Completed Interrupt Disable
bits : 0 - 0 (1 bit)
access : write-only
RXRDY : Receive Holding Register Ready Interrupt Disable
bits : 1 - 1 (1 bit)
access : write-only
TXRDY : Transmit Holding Register Ready Interrupt Disable
bits : 2 - 2 (1 bit)
access : write-only
SVACC : Slave Access Interrupt Disable
bits : 4 - 4 (1 bit)
access : write-only
GACC : General Call Access Interrupt Disable
bits : 5 - 5 (1 bit)
access : write-only
OVRE : Overrun Error Interrupt Disable
bits : 6 - 6 (1 bit)
access : write-only
NACK : Not Acknowledge Interrupt Disable
bits : 8 - 8 (1 bit)
access : write-only
ARBLST : Arbitration Lost Interrupt Disable
bits : 9 - 9 (1 bit)
access : write-only
SCL_WS : Clock Wait State Interrupt Disable
bits : 10 - 10 (1 bit)
access : write-only
EOSACC : End Of Slave Access Interrupt Disable
bits : 11 - 11 (1 bit)
access : write-only
ENDRX : End of Receive Buffer Interrupt Disable
bits : 12 - 12 (1 bit)
access : write-only
ENDTX : End of Transmit Buffer Interrupt Disable
bits : 13 - 13 (1 bit)
access : write-only
RXBUFF : Receive Buffer Full Interrupt Disable
bits : 14 - 14 (1 bit)
access : write-only
TXBUFE : Transmit Buffer Empty Interrupt Disable
bits : 15 - 15 (1 bit)
access : write-only
Interrupt Mask Register
address_offset : 0x2C Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
TXCOMP : Transmission Completed Interrupt Mask
bits : 0 - 0 (1 bit)
access : read-only
RXRDY : Receive Holding Register Ready Interrupt Mask
bits : 1 - 1 (1 bit)
access : read-only
TXRDY : Transmit Holding Register Ready Interrupt Mask
bits : 2 - 2 (1 bit)
access : read-only
SVACC : Slave Access Interrupt Mask
bits : 4 - 4 (1 bit)
access : read-only
GACC : General Call Access Interrupt Mask
bits : 5 - 5 (1 bit)
access : read-only
OVRE : Overrun Error Interrupt Mask
bits : 6 - 6 (1 bit)
access : read-only
NACK : Not Acknowledge Interrupt Mask
bits : 8 - 8 (1 bit)
access : read-only
ARBLST : Arbitration Lost Interrupt Mask
bits : 9 - 9 (1 bit)
access : read-only
SCL_WS : Clock Wait State Interrupt Mask
bits : 10 - 10 (1 bit)
access : read-only
EOSACC : End Of Slave Access Interrupt Mask
bits : 11 - 11 (1 bit)
access : read-only
ENDRX : End of Receive Buffer Interrupt Mask
bits : 12 - 12 (1 bit)
access : read-only
ENDTX : End of Transmit Buffer Interrupt Mask
bits : 13 - 13 (1 bit)
access : read-only
RXBUFF : Receive Buffer Full Interrupt Mask
bits : 14 - 14 (1 bit)
access : read-only
TXBUFE : Transmit Buffer Empty Interrupt Mask
bits : 15 - 15 (1 bit)
access : read-only
Receive Holding Register
address_offset : 0x30 Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
RXDATA : Master or Slave Receive Holding Data
bits : 0 - 7 (8 bit)
access : read-only
Transmit Holding Register
address_offset : 0x34 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
TXDATA : Master or Slave Transmit Holding Data
bits : 0 - 7 (8 bit)
access : write-only
Master Mode Register
address_offset : 0x4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
IADRSZ : Internal Device Address Size
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
0x0 : NONE
No internal device address
0x1 : 1_BYTE
One-byte internal device address
0x2 : 2_BYTE
Two-byte internal device address
0x3 : 3_BYTE
Three-byte internal device address
End of enumeration elements list.
MREAD : Master Read Direction
bits : 12 - 12 (1 bit)
access : read-write
DADR : Device Address
bits : 16 - 22 (7 bit)
access : read-write
Slave Mode Register
address_offset : 0x8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
SADR : Slave Address
bits : 16 - 22 (7 bit)
access : read-write
Internal Address Register
address_offset : 0xC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
IADR : Internal Address
bits : 0 - 23 (24 bit)
access : read-write
Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !
This website is sponsored by Embeetle, an IDE designed from scratch for embedded software developers.