Embeetle, an IDE designed from scratch for embedded software developers.address_offset : 0x0 Bytes (0x0)
size : 0x28 byte (0x0)
mem_usage : registers
protection :
GPIO Port 5 Configuration
address_offset : 0x0 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
CON0 : p5.0 configuration bits
bits : 0 - 1 (2 bit)
Enumeration:
0 : GPIO
GPIO
1 : VDAC3
VDAC3
End of enumeration elements list.
CON1 : p5.1 configuration bits
bits : 2 - 3 (2 bit)
Enumeration:
0 : GPIO
GPIO
1 : VDAC6
VDAC6
End of enumeration elements list.
CON2 : p5.2 configuration bits
bits : 4 - 5 (2 bit)
Enumeration:
0 : GPIO
GPIO
1 : VDAC7
VDAC7
End of enumeration elements list.
CON3 : p5.3 configuration bits
bits : 6 - 7 (2 bit)
Enumeration:
0 : GPIO
GPIO
1 : VDAC0
VDAC0
End of enumeration elements list.
GPIO Port 5 registered data input
address_offset : 0x10 Bytes (0x0)
size : 4 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
IN0 : Registered data input
bits : 0 - 0 (1 bit)
Enumeration:
0 : LOW
1 : HIGH
End of enumeration elements list.
IN1 : Registered data input
bits : 1 - 1 (1 bit)
Enumeration:
0 : LOW
1 : HIGH
End of enumeration elements list.
IN2 : Registered data input
bits : 2 - 2 (1 bit)
Enumeration:
0 : LOW
1 : HIGH
End of enumeration elements list.
IN3 : Registered data input
bits : 3 - 3 (1 bit)
Enumeration:
0 : LOW
1 : HIGH
End of enumeration elements list.
GPIO Port 5 data output
address_offset : 0x14 Bytes (0x0)
size : 4 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OUT0 : Data out
bits : 0 - 0 (1 bit)
Enumeration:
0 : LOW
1 : HIGH
End of enumeration elements list.
OUT1 : Data out
bits : 1 - 1 (1 bit)
Enumeration:
0 : LOW
1 : HIGH
End of enumeration elements list.
OUT2 : Data out
bits : 2 - 2 (1 bit)
Enumeration:
0 : LOW
1 : HIGH
End of enumeration elements list.
OUT3 : Data out
bits : 3 - 3 (1 bit)
Enumeration:
0 : LOW
1 : HIGH
End of enumeration elements list.
GPIO Port 5 data out set
address_offset : 0x18 Bytes (0x0)
size : 4 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
SET0 : Set the output HIGH for the pin
bits : 0 - 0 (1 bit)
Enumeration:
1 : SET
End of enumeration elements list.
SET1 : Set the output HIGH for the pin
bits : 1 - 1 (1 bit)
Enumeration:
1 : SET
End of enumeration elements list.
SET2 : Set the output HIGH for the pin
bits : 2 - 2 (1 bit)
Enumeration:
1 : SET
End of enumeration elements list.
SET3 : Set the output HIGH for the pin
bits : 3 - 3 (1 bit)
Enumeration:
1 : SET
End of enumeration elements list.
GPIO Port 5 data out clear
address_offset : 0x1C Bytes (0x0)
size : 4 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
CLR0 : Set the output low for the port pin
bits : 0 - 0 (1 bit)
Enumeration:
1 : CLR
End of enumeration elements list.
CLR1 : Set the output low for the port pin
bits : 1 - 1 (1 bit)
Enumeration:
1 : CLR
End of enumeration elements list.
CLR2 : Set the output low for the port pin
bits : 2 - 2 (1 bit)
Enumeration:
1 : CLR
End of enumeration elements list.
CLR3 : Set the output low for the port pin
bits : 3 - 3 (1 bit)
Enumeration:
1 : CLR
End of enumeration elements list.
GPIO Port 5 pin toggle
address_offset : 0x20 Bytes (0x0)
size : 4 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
TGL0 : Toggle the output of the port pin
bits : 0 - 0 (1 bit)
Enumeration:
1 : TGL
End of enumeration elements list.
TGL1 : Toggle the output of the port pin
bits : 1 - 1 (1 bit)
Enumeration:
1 : TGL
End of enumeration elements list.
TGL2 : Toggle the output of the port pin
bits : 2 - 2 (1 bit)
Enumeration:
1 : TGL
End of enumeration elements list.
TGL3 : Toggle the output of the port pin
bits : 3 - 3 (1 bit)
Enumeration:
1 : TGL
End of enumeration elements list.
GPIO Port 5 open drain enable
address_offset : 0x24 Bytes (0x0)
size : 4 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
ODE0 : Open drain enable
bits : 0 - 0 (1 bit)
Enumeration:
0 : DIS
1 : EN
End of enumeration elements list.
ODE1 : Open drain enable
bits : 1 - 1 (1 bit)
Enumeration:
0 : DIS
1 : EN
End of enumeration elements list.
ODE2 : Open drain enable
bits : 2 - 2 (1 bit)
Enumeration:
0 : DIS
1 : EN
End of enumeration elements list.
ODE3 : Open drain enable
bits : 3 - 3 (1 bit)
Enumeration:
0 : DIS
1 : EN
End of enumeration elements list.
GPIO Port 5 output enable
address_offset : 0x4 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OE0 : Pin Output Drive enable
bits : 0 - 0 (1 bit)
Enumeration:
0 : DIS
1 : EN
End of enumeration elements list.
OE1 : Pin Output Drive enable
bits : 1 - 1 (1 bit)
Enumeration:
0 : DIS
1 : EN
End of enumeration elements list.
OE2 : Pin Output Drive enable
bits : 2 - 2 (1 bit)
Enumeration:
0 : DIS
1 : EN
End of enumeration elements list.
OE3 : Pin Output Drive enable
bits : 3 - 3 (1 bit)
Enumeration:
0 : DIS
1 : EN
End of enumeration elements list.
GPIO Port 5 pull down enable
address_offset : 0x8 Bytes (0x0)
size : 4 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PUL0 : Pin Pull down enable
bits : 0 - 0 (1 bit)
Enumeration:
0 : DIS
1 : EN
End of enumeration elements list.
PUL1 : Pin Pull down enable
bits : 1 - 1 (1 bit)
Enumeration:
0 : DIS
1 : EN
End of enumeration elements list.
PUL2 : Pin Pull down enable
bits : 2 - 2 (1 bit)
Enumeration:
0 : DIS
1 : EN
End of enumeration elements list.
PUL3 : Pin Pull down enable
bits : 3 - 3 (1 bit)
Enumeration:
0 : DIS
1 : EN
End of enumeration elements list.
GPIO Port 5 Input Path Enable
address_offset : 0xC Bytes (0x0)
size : 4 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
IEN0 : Input path enable
bits : 0 - 0 (1 bit)
Enumeration:
0 : DIS
1 : EN
End of enumeration elements list.
IEN1 : Input path enable
bits : 1 - 1 (1 bit)
Enumeration:
0 : DIS
1 : EN
End of enumeration elements list.
IEN2 : Input path enable
bits : 2 - 2 (1 bit)
Enumeration:
0 : DIS
1 : EN
End of enumeration elements list.
IEN3 : Input path enable
bits : 3 - 3 (1 bit)
Enumeration:
0 : DIS
1 : EN
End of enumeration elements list.
Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !
This website is sponsored by Embeetle, an IDE designed from scratch for embedded software developers.