CON

TXFIFO

RXFIFO

CLKDIV

IE

STATUS

I2SEN : Enable I2S Controller
bits : 0 - 0 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

TXEN : Transmit Enable
bits : 1 - 1 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

RXEN : Receive Enable
bits : 2 - 2 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

MUTE : Transmit Mute Enable
bits : 3 - 3 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

WORDWIDTH : Word Width This parameter sets the word width of audio data. See Figure 563 for details of how data is formatted in transmit and receive FIFO.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

End of enumeration elements list.

MONO : Monaural data This parameter sets whether mono or stereo data is processed. See Figure 563 for details of how data is formatted in transmit and receive FIFO.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

FORMAT : Data format See Figure 561 and Figure 562 for timing differences.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

SLAVE : Slave Mode I2S can operate as a master or slave. For master mode, I2S_BCLK and I2S_FS pins are outputs and send bit clock and frame sync from ISD9160. In slave mode, I2S_BCLK and I2S_FS pins are inputs and bit clock and frame sync are received from external audio device.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

TXTH : Transmit FIFO Threshold Level If remaining data words in transmit FIFO less than or equal to the threshold level then TXTHI flag is set.
bits : 9 - 11 (3 bit)
access : read-write

RXTH : Receive FIFO Threshold Level When received data word(s) in buffer is equal or higher than threshold level then RXTHI flag is set.
bits : 12 - 14 (3 bit)
access : read-write

MCLKEN : Master Clock Enable The ISD9160 can generate a master clock signal to an external audio CODEC to synchronize the audio devices. If audio devices are not synchronous, then data will be periodically corrupted. Software needs to implement a way to drop/repeat or interpolate samples in a jitter buffer if devices are not synchronized. The master clock frequency is determined by the CLKDIV.MCLK_DIV[2:0] register.
bits : 15 - 15 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

RCHZCEN : Right Channel Zero Cross Detect Enable If this bit is set to 1, when right channel data sign bit changes, or data bits are all zero, the RZCF flag in I2S_STATUS register will be set to 1.
bits : 16 - 16 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

LCHZCEN : Left Channel Zero Cross Detect Enable If this bit is set to 1, when left channel data sign bit changes, or data bits are all zero, the LZCF flag in I2S_STATUS register will be set to 1.
bits : 17 - 17 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

CLR_TXFIFO : Clear Transmit FIFO Write 1 to clear transmit FIFO, internal pointer is reset to FIFO start point, and TXFIFO_LEVEL[3:0] returns to zero and transmit FIFO becomes empty. Data in transmit FIFO is not changed. This bit is cleared by hardware automatically when clear operation complete.
bits : 18 - 18 (1 bit)
access : read-write

CLR_RXFIFO : Clear Receive FIFO Write 1 to clear receive FIFO, internal pointer is reset to FIFO start point, and RXFIFO_LEVEL[3:0] returns to zero and receive FIFO becomes empty. This bit is cleared by hardware automatically when clear operation complete.
bits : 19 - 19 (1 bit)
access : read-write

TXDMA : Enable Transmit DMA When TX DMA is enables, I2S request DMA to transfer data from SRAM to transmit FIFO if FIFO is not full.
bits : 20 - 20 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

RXDMA : Enable Receive DMA When RX DMA is enabled, I2S requests DMA to transfer data from receive FIFO to SRAM if FIFO is not empty.
bits : 21 - 21 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

TXFIFO : Transmit FIFO Register (Write Only) A write to this register pushes data onto the transmit FIFO. The transmit FIFO is eight words deep. The number of words currently in the FIFO can be determined by reading I2S->STATUS.TX_LEVEL.
bits : 0 - 31 (32 bit)
access : write-only

RXFIFO : Receive FIFO Register (Read Only) A read of this register will pop data from the receive FIFO. The receive FIFO is eight words deep. The number of words currently in the FIFO can be determined by reading I2S->STATUS.RX_LEVEL.
bits : 0 - 31 (32 bit)
access : read-only

MCLK_DIV : Master Clock Divider ISD9160 can generate a master clock to synchronously drive an external audio device. If MCLK_DIV is set to 0, MCLK is the same as I2S_CLK clock input, otherwise MCLK frequency is given by: F(MCLK) = F(I2S_CLK) / (2xMCLK_DIV) Or, MCLK_DIV = F(I2S_CLK) / (2 x F(MCLK)) If the desired MCLK frequency is 254Fs and Fs = 16kHz then MCLK_DIV = 6
bits : 0 - 2 (3 bit)
access : read-write

BCLK_DIV : Bit Clock Divider If I2S operates in master mode, bit clock is provided by ISD9160. Software can program these bits to generate bit clock frequency for the desired sample rate. For sample rate Fs, the desired bit clock frequency is: F(BCLK) = Fs x Word_width_in_bytes x 16 For example if Fs = 16kHz, and word width is 2-bytes (16bit) then desired bit clock frequency is 512kHz. The bit clock frequency is given by: F(BCLK) = F(I2S_CLK) / 2x(BCLK_DIV+1) Or, BCLK_DIV = F(I2S_CLK) / (2 x F(BCLK)) -1 So if F(I2S_CLK) = HCLK = 49.152MHz , desired F(BCLK) = 512kHz then BCLK_DIV = 47
bits : 8 - 15 (8 bit)
access : read-write

RXUDFIE : Receive FIFO Underflow Interrupt Enable If software read receive FIFO when it is empty then RXUDF flag in I2SSTATUS register is set to 1.
bits : 0 - 0 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

RXOVFIE : Receive FIFO Overflow Interrupt Enable
bits : 1 - 1 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

RXTHIE : Receive FIFO Threshold Level Interrupt Interrupt occurs if this bit is set to 1 and data words in receive FIFO is greater than or equal to RXTH[2:0].
bits : 2 - 2 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

TXUDFIE : Transmit FIFO Underflow Interrupt Enable Interrupt occur if this bit is set to 1 and transmit FIFO underflow flag is set to 1.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

TXOVFIE : Transmit FIFO Overflow Interrupt Enable Interrupt occurs if this bit is set to 1 and transmit FIFO overflow flag is set to 1
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

TXTHIE : Transmit FIFO Threshold Level Interrupt Enable Interrupt occurs if this bit is set to 1 and data words in transmit FIFO is less than TXTH[2:0].
bits : 10 - 10 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

RZCIE : Right Channel Zero Cross Interrupt Enable Interrupt will occur if this bit is set to 1 and right channel has zero cross event
bits : 11 - 11 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

LZCIE : Left Channel Zero Cross Interrupt Enable Interrupt will occur if this bit is set to 1 and left channel has zero cross event
bits : 12 - 12 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

I2SINT : I2S Interrupt (Read Only) This bit is set if any enabled I2S interrupt is active.
bits : 0 - 0 (1 bit)
access : read-only

Enumeration:

End of enumeration elements list.

I2SRXINT : I2S Receive Interrupt (Read Only) This indicates that there is an active receive interrupt source. This could be RXOVF, RXUDF or RXTHF if corresponding interrupt enable bits are active. To clear interrupt the corresponding source(s) must be cleared.
bits : 1 - 1 (1 bit)
access : read-only

Enumeration:

End of enumeration elements list.

I2STXINT : I2S Transmit Interrupt (Read Only) This indicates that there is an active transmit interrupt source. This could be TXOVF, TXUDF, TXTHF, LZCF or RZCF if corresponding interrupt enable bits are active. To clear interrupt the corresponding source(s) must be cleared.
bits : 2 - 2 (1 bit)
access : read-only

Enumeration:

End of enumeration elements list.

RIGHT : Right Channel Active (Read Only) This bit indicates current data being transmitted/received belongs to right channel
bits : 3 - 3 (1 bit)
access : read-only

Enumeration:

End of enumeration elements list.

RXUDF : Receive FIFO Underflow Flag (Write '1' to clear) This flag is set if attempt is made to read receive FIFO while it is empty.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

RXOVF : Receive FIFO Overflow Flag (Write '1' to clear) This flag is set if I2S controller writes to receive FIFO when it is full. Audio data is lost.
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

RXTHF : Receive FIFO Threshold Flag (Read Only) When data word(s) in receive FIFO is greater than or equal to threshold value set in RXTH[2:0] the RXTHF bit becomes to 1. It remains set until receive FIFO level is less than RXTH[2:0]. It is cleared by reading RXFIFO until threshold satisfied.
bits : 10 - 10 (1 bit)
access : read-only

Enumeration:

End of enumeration elements list.

RXFULL : Receive FIFO full (Read Only) This bit is set when receive FIFO is full.
bits : 11 - 11 (1 bit)
access : read-only

Enumeration:

End of enumeration elements list.

RXEMPTY : Receive FIFO empty (Read Only) This is set when receive FIFO is empty.
bits : 12 - 12 (1 bit)
access : read-only

Enumeration:

End of enumeration elements list.

TXUDF : Transmit FIFO underflow flag (Write '1' to clear) This flag is set if I2S controller requests data when transmit FIFO is empty.
bits : 16 - 16 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

TXOVF : Transmit FIFO Overflow Flag (Write '1' to clear) This flag is set if data is written to transmit FIFO when it is full.
bits : 17 - 17 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

TXTHF : Transmit FIFO Threshold Flag (Read Only) When data word(s) in transmit FIFO is less than or equal to the threshold value set in TXTH[2:0] the TXTHF bit becomes to 1. It remains set until transmit FIFO level is greater than TXTH[2:0]. Cleared by writing to TXFIFO register until threshold exceeded.
bits : 18 - 18 (1 bit)
access : read-only

Enumeration:

End of enumeration elements list.

TXFULL : Transmit FIFO Full (Read Only) This bit is set when transmit FIFO is full.
bits : 19 - 19 (1 bit)
access : read-only

Enumeration:

End of enumeration elements list.

TXEMPTY : Transmit FIFO Empty (Read Only) This is set when transmit FIFO is empty.
bits : 20 - 20 (1 bit)
access : read-only

Enumeration:

End of enumeration elements list.

TXBUSY : Transmit Busy (Read Only) This bit is cleared when all data in transmit FIFO and Tx shift register is shifted out. It is set when first data is loaded to Tx shift register.
bits : 21 - 21 (1 bit)
access : read-only

Enumeration:

End of enumeration elements list.

RZCF : Right channel zero cross flag (write '1' to clear, or clear RCHZCEN)
bits : 22 - 22 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

LZCF : Left channel zero cross flag (write '1' to clear, or clear LCHZCEN)
bits : 23 - 23 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

RX_LEVEL : Receive FIFO level (Read Only)
bits : 24 - 27 (4 bit)
access : read-only

TX_LEVEL : Transmit FIFO level (Read Only)
bits : 28 - 31 (4 bit)
access : read-only