Embeetle, an IDE designed from scratch for embedded software developers.address_offset : 0x0 Bytes (0x0)
size : 0x464 byte (0x0)
mem_usage : registers
protection :
PWM Clock Register
address_offset : 0x0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DIVA : CLKA Divide Factor
bits : 0 - 7 (8 bit)
Enumeration: DIVASelect
0 : CLKA_POFF
CLKA clock is turned off
1 : PREA
CLKA clock is clock selected by PREA
End of enumeration elements list.
PREA : CLKA Source Clock Selection
bits : 8 - 11 (4 bit)
Enumeration: PREASelect
0x0 : CLK
Peripheral clock
0x1 : CLK_DIV2
Peripheral clock/2
0x2 : CLK_DIV4
Peripheral clock/4
0x3 : CLK_DIV8
Peripheral clock/8
0x4 : CLK_DIV16
Peripheral clock/16
0x5 : CLK_DIV32
Peripheral clock/32
0x6 : CLK_DIV64
Peripheral clock/64
0x7 : CLK_DIV128
Peripheral clock/128
0x8 : CLK_DIV256
Peripheral clock/256
0x9 : CLK_DIV512
Peripheral clock/512
0xA : CLK_DIV1024
Peripheral clock/1024
End of enumeration elements list.
DIVB : CLKB Divide Factor
bits : 16 - 23 (8 bit)
Enumeration: DIVBSelect
0 : CLKB_POFF
CLKB clock is turned off
1 : PREB
CLKB clock is clock selected by PREB
End of enumeration elements list.
PREB : CLKB Source Clock Selection
bits : 24 - 27 (4 bit)
Enumeration: PREBSelect
0x0 : CLK
Peripheral clock
0x1 : CLK_DIV2
Peripheral clock/2
0x2 : CLK_DIV4
Peripheral clock/4
0x3 : CLK_DIV8
Peripheral clock/8
0x4 : CLK_DIV16
Peripheral clock/16
0x5 : CLK_DIV32
Peripheral clock/32
0x6 : CLK_DIV64
Peripheral clock/64
0x7 : CLK_DIV128
Peripheral clock/128
0x8 : CLK_DIV256
Peripheral clock/256
0x9 : CLK_DIV512
Peripheral clock/512
0xA : CLK_DIV1024
Peripheral clock/1024
End of enumeration elements list.
PWM Comparison 0 Value Register
address_offset : 0x0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
CV : Comparison x Value
bits : 0 - 23 (24 bit)
CVM : Comparison x Value Mode
bits : 24 - 24 (1 bit)
Enumeration: CVMSelect
0x0 : COMPARE_AT_INCREMENT
Compare when counter is incrementing
0x1 : COMPARE_AT_DECREMENT
Compare when counter is decrementing
End of enumeration elements list.
PWM Channel Mode Register
address_offset : 0x0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
CPRE : Channel Pre-scaler
bits : 0 - 3 (4 bit)
Enumeration: CPRESelect
0x0 : MCK
Peripheral clock
0x1 : MCK_DIV_2
Peripheral clock/2
0x2 : MCK_DIV_4
Peripheral clock/4
0x3 : MCK_DIV_8
Peripheral clock/8
0x4 : MCK_DIV_16
Peripheral clock/16
0x5 : MCK_DIV_32
Peripheral clock/32
0x6 : MCK_DIV_64
Peripheral clock/64
0x7 : MCK_DIV_128
Peripheral clock/128
0x8 : MCK_DIV_256
Peripheral clock/256
0x9 : MCK_DIV_512
Peripheral clock/512
0xA : MCK_DIV_1024
Peripheral clock/1024
0xB : CLKA
Clock A
0xC : CLKB
Clock B
End of enumeration elements list.
CALG : Channel Alignment
bits : 8 - 8 (1 bit)
Enumeration: CALGSelect
0x0 : LEFT_ALIGNED
Left aligned
0x1 : CENTER_ALIGNED
Center aligned
End of enumeration elements list.
CPOL : Channel Polarity
bits : 9 - 9 (1 bit)
Enumeration: CPOLSelect
0x0 : LOW_POLARITY
Waveform starts at low level
0x1 : HIGH_POLARITY
Waveform starts at high level
End of enumeration elements list.
CES : Counter Event Selection
bits : 10 - 10 (1 bit)
Enumeration: CESSelect
0x0 : SINGLE_EVENT
At the end of PWM period
0x1 : DOUBLE_EVENT
At half of PWM period AND at the end of PWM period
End of enumeration elements list.
UPDS : Update Selection
bits : 11 - 11 (1 bit)
Enumeration: UPDSSelect
0x0 : UPDATE_AT_PERIOD
At the next end of PWM period
0x1 : UPDATE_AT_HALF_PERIOD
At the next end of Half PWM period
End of enumeration elements list.
DPOLI : Disabled Polarity Inverted
bits : 12 - 12 (1 bit)
TCTS : Timer Counter Trigger Selection
bits : 13 - 13 (1 bit)
DTE : Dead-Time Generator Enable
bits : 16 - 16 (1 bit)
DTHI : Dead-Time PWMHx Output Inverted
bits : 17 - 17 (1 bit)
DTLI : Dead-Time PWMLx Output Inverted
bits : 18 - 18 (1 bit)
PPM : Push-Pull Mode
bits : 19 - 19 (1 bit)
PWM Clock Register
address_offset : 0x0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DIVA : CLKA Divide Factor
bits : 0 - 7 (8 bit)
Enumeration: DIVASelect
0 : CLKA_POFF
CLKA clock is turned off
1 : PREA
CLKA clock is clock selected by PREA
End of enumeration elements list.
PREA : CLKA Source Clock Selection
bits : 8 - 11 (4 bit)
Enumeration: PREASelect
0x0 : CLK
Peripheral clock
0x1 : CLK_DIV2
Peripheral clock/2
0x2 : CLK_DIV4
Peripheral clock/4
0x3 : CLK_DIV8
Peripheral clock/8
0x4 : CLK_DIV16
Peripheral clock/16
0x5 : CLK_DIV32
Peripheral clock/32
0x6 : CLK_DIV64
Peripheral clock/64
0x7 : CLK_DIV128
Peripheral clock/128
0x8 : CLK_DIV256
Peripheral clock/256
0x9 : CLK_DIV512
Peripheral clock/512
0xA : CLK_DIV1024
Peripheral clock/1024
End of enumeration elements list.
DIVB : CLKB Divide Factor
bits : 16 - 23 (8 bit)
Enumeration: DIVBSelect
0 : CLKB_POFF
CLKB clock is turned off
1 : PREB
CLKB clock is clock selected by PREB
End of enumeration elements list.
PREB : CLKB Source Clock Selection
bits : 24 - 27 (4 bit)
Enumeration: PREBSelect
0x0 : CLK
Peripheral clock
0x1 : CLK_DIV2
Peripheral clock/2
0x2 : CLK_DIV4
Peripheral clock/4
0x3 : CLK_DIV8
Peripheral clock/8
0x4 : CLK_DIV16
Peripheral clock/16
0x5 : CLK_DIV32
Peripheral clock/32
0x6 : CLK_DIV64
Peripheral clock/64
0x7 : CLK_DIV128
Peripheral clock/128
0x8 : CLK_DIV256
Peripheral clock/256
0x9 : CLK_DIV512
Peripheral clock/512
0xA : CLK_DIV1024
Peripheral clock/1024
End of enumeration elements list.
PWM Comparison 0 Value Register
address_offset : 0x0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
CV : Comparison x Value
bits : 0 - 23 (24 bit)
CVM : Comparison x Value Mode
bits : 24 - 24 (1 bit)
Enumeration: CVMSelect
0x0 : COMPARE_AT_INCREMENT
Compare when counter is incrementing
0x1 : COMPARE_AT_DECREMENT
Compare when counter is decrementing
End of enumeration elements list.
PWM Channel Mode Register
address_offset : 0x0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
CPRE : Channel Pre-scaler
bits : 0 - 3 (4 bit)
Enumeration: CPRESelect
0x0 : MCK
Peripheral clock
0x1 : MCK_DIV_2
Peripheral clock/2
0x2 : MCK_DIV_4
Peripheral clock/4
0x3 : MCK_DIV_8
Peripheral clock/8
0x4 : MCK_DIV_16
Peripheral clock/16
0x5 : MCK_DIV_32
Peripheral clock/32
0x6 : MCK_DIV_64
Peripheral clock/64
0x7 : MCK_DIV_128
Peripheral clock/128
0x8 : MCK_DIV_256
Peripheral clock/256
0x9 : MCK_DIV_512
Peripheral clock/512
0xA : MCK_DIV_1024
Peripheral clock/1024
0xB : CLKA
Clock A
0xC : CLKB
Clock B
End of enumeration elements list.
CALG : Channel Alignment
bits : 8 - 8 (1 bit)
Enumeration: CALGSelect
0x0 : LEFT_ALIGNED
Left aligned
0x1 : CENTER_ALIGNED
Center aligned
End of enumeration elements list.
CPOL : Channel Polarity
bits : 9 - 9 (1 bit)
Enumeration: CPOLSelect
0x0 : LOW_POLARITY
Waveform starts at low level
0x1 : HIGH_POLARITY
Waveform starts at high level
End of enumeration elements list.
CES : Counter Event Selection
bits : 10 - 10 (1 bit)
Enumeration: CESSelect
0x0 : SINGLE_EVENT
At the end of PWM period
0x1 : DOUBLE_EVENT
At half of PWM period AND at the end of PWM period
End of enumeration elements list.
UPDS : Update Selection
bits : 11 - 11 (1 bit)
Enumeration: UPDSSelect
0x0 : UPDATE_AT_PERIOD
At the next end of PWM period
0x1 : UPDATE_AT_HALF_PERIOD
At the next end of Half PWM period
End of enumeration elements list.
DPOLI : Disabled Polarity Inverted
bits : 12 - 12 (1 bit)
TCTS : Timer Counter Trigger Selection
bits : 13 - 13 (1 bit)
DTE : Dead-Time Generator Enable
bits : 16 - 16 (1 bit)
DTHI : Dead-Time PWMHx Output Inverted
bits : 17 - 17 (1 bit)
DTLI : Dead-Time PWMLx Output Inverted
bits : 18 - 18 (1 bit)
PPM : Push-Pull Mode
bits : 19 - 19 (1 bit)
PWM Interrupt Enable Register 1
address_offset : 0x10 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
CHID0 : Counter Event on Channel 0 Interrupt Enable
bits : 0 - 0 (1 bit)
CHID1 : Counter Event on Channel 1 Interrupt Enable
bits : 1 - 1 (1 bit)
CHID2 : Counter Event on Channel 2 Interrupt Enable
bits : 2 - 2 (1 bit)
CHID3 : Counter Event on Channel 3 Interrupt Enable
bits : 3 - 3 (1 bit)
FCHID0 : Fault Protection Trigger on Channel 0 Interrupt Enable
bits : 16 - 16 (1 bit)
FCHID1 : Fault Protection Trigger on Channel 1 Interrupt Enable
bits : 17 - 17 (1 bit)
FCHID2 : Fault Protection Trigger on Channel 2 Interrupt Enable
bits : 18 - 18 (1 bit)
FCHID3 : Fault Protection Trigger on Channel 3 Interrupt Enable
bits : 19 - 19 (1 bit)
PWM Channel Period Update Register
address_offset : 0x10 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
CPRDUPD : Channel Period Update
bits : 0 - 23 (24 bit)
PWM Interrupt Enable Register 1
address_offset : 0x10 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
CHID0 : Counter Event on Channel 0 Interrupt Enable
bits : 0 - 0 (1 bit)
CHID1 : Counter Event on Channel 1 Interrupt Enable
bits : 1 - 1 (1 bit)
CHID2 : Counter Event on Channel 2 Interrupt Enable
bits : 2 - 2 (1 bit)
CHID3 : Counter Event on Channel 3 Interrupt Enable
bits : 3 - 3 (1 bit)
FCHID0 : Fault Protection Trigger on Channel 0 Interrupt Enable
bits : 16 - 16 (1 bit)
FCHID1 : Fault Protection Trigger on Channel 1 Interrupt Enable
bits : 17 - 17 (1 bit)
FCHID2 : Fault Protection Trigger on Channel 2 Interrupt Enable
bits : 18 - 18 (1 bit)
FCHID3 : Fault Protection Trigger on Channel 3 Interrupt Enable
bits : 19 - 19 (1 bit)
PWM Channel Period Update Register
address_offset : 0x10 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
CPRDUPD : Channel Period Update
bits : 0 - 23 (24 bit)
PWM Interrupt Disable Register 1
address_offset : 0x14 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
CHID0 : Counter Event on Channel 0 Interrupt Disable
bits : 0 - 0 (1 bit)
CHID1 : Counter Event on Channel 1 Interrupt Disable
bits : 1 - 1 (1 bit)
CHID2 : Counter Event on Channel 2 Interrupt Disable
bits : 2 - 2 (1 bit)
CHID3 : Counter Event on Channel 3 Interrupt Disable
bits : 3 - 3 (1 bit)
FCHID0 : Fault Protection Trigger on Channel 0 Interrupt Disable
bits : 16 - 16 (1 bit)
FCHID1 : Fault Protection Trigger on Channel 1 Interrupt Disable
bits : 17 - 17 (1 bit)
FCHID2 : Fault Protection Trigger on Channel 2 Interrupt Disable
bits : 18 - 18 (1 bit)
FCHID3 : Fault Protection Trigger on Channel 3 Interrupt Disable
bits : 19 - 19 (1 bit)
PWM Channel Counter Register
address_offset : 0x14 Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
CNT : Channel Counter Register
bits : 0 - 23 (24 bit)
PWM Interrupt Disable Register 1
address_offset : 0x14 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
CHID0 : Counter Event on Channel 0 Interrupt Disable
bits : 0 - 0 (1 bit)
CHID1 : Counter Event on Channel 1 Interrupt Disable
bits : 1 - 1 (1 bit)
CHID2 : Counter Event on Channel 2 Interrupt Disable
bits : 2 - 2 (1 bit)
CHID3 : Counter Event on Channel 3 Interrupt Disable
bits : 3 - 3 (1 bit)
FCHID0 : Fault Protection Trigger on Channel 0 Interrupt Disable
bits : 16 - 16 (1 bit)
FCHID1 : Fault Protection Trigger on Channel 1 Interrupt Disable
bits : 17 - 17 (1 bit)
FCHID2 : Fault Protection Trigger on Channel 2 Interrupt Disable
bits : 18 - 18 (1 bit)
FCHID3 : Fault Protection Trigger on Channel 3 Interrupt Disable
bits : 19 - 19 (1 bit)
PWM Channel Counter Register
address_offset : 0x14 Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
CNT : Channel Counter Register
bits : 0 - 23 (24 bit)
PWM Interrupt Mask Register 1
address_offset : 0x18 Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
CHID0 : Counter Event on Channel 0 Interrupt Mask
bits : 0 - 0 (1 bit)
CHID1 : Counter Event on Channel 1 Interrupt Mask
bits : 1 - 1 (1 bit)
CHID2 : Counter Event on Channel 2 Interrupt Mask
bits : 2 - 2 (1 bit)
CHID3 : Counter Event on Channel 3 Interrupt Mask
bits : 3 - 3 (1 bit)
FCHID0 : Fault Protection Trigger on Channel 0 Interrupt Mask
bits : 16 - 16 (1 bit)
FCHID1 : Fault Protection Trigger on Channel 1 Interrupt Mask
bits : 17 - 17 (1 bit)
FCHID2 : Fault Protection Trigger on Channel 2 Interrupt Mask
bits : 18 - 18 (1 bit)
FCHID3 : Fault Protection Trigger on Channel 3 Interrupt Mask
bits : 19 - 19 (1 bit)
PWM Channel Dead Time Register
address_offset : 0x18 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DTH : Dead-Time Value for PWMHx Output
bits : 0 - 15 (16 bit)
DTL : Dead-Time Value for PWMLx Output
bits : 16 - 31 (16 bit)
PWM Interrupt Mask Register 1
address_offset : 0x18 Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
CHID0 : Counter Event on Channel 0 Interrupt Mask
bits : 0 - 0 (1 bit)
CHID1 : Counter Event on Channel 1 Interrupt Mask
bits : 1 - 1 (1 bit)
CHID2 : Counter Event on Channel 2 Interrupt Mask
bits : 2 - 2 (1 bit)
CHID3 : Counter Event on Channel 3 Interrupt Mask
bits : 3 - 3 (1 bit)
FCHID0 : Fault Protection Trigger on Channel 0 Interrupt Mask
bits : 16 - 16 (1 bit)
FCHID1 : Fault Protection Trigger on Channel 1 Interrupt Mask
bits : 17 - 17 (1 bit)
FCHID2 : Fault Protection Trigger on Channel 2 Interrupt Mask
bits : 18 - 18 (1 bit)
FCHID3 : Fault Protection Trigger on Channel 3 Interrupt Mask
bits : 19 - 19 (1 bit)
PWM Channel Dead Time Register
address_offset : 0x18 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DTH : Dead-Time Value for PWMHx Output
bits : 0 - 15 (16 bit)
DTL : Dead-Time Value for PWMLx Output
bits : 16 - 31 (16 bit)
PWM Interrupt Status Register 1
address_offset : 0x1C Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
CHID0 : Counter Event on Channel 0
bits : 0 - 0 (1 bit)
CHID1 : Counter Event on Channel 1
bits : 1 - 1 (1 bit)
CHID2 : Counter Event on Channel 2
bits : 2 - 2 (1 bit)
CHID3 : Counter Event on Channel 3
bits : 3 - 3 (1 bit)
FCHID0 : Fault Protection Trigger on Channel 0
bits : 16 - 16 (1 bit)
FCHID1 : Fault Protection Trigger on Channel 1
bits : 17 - 17 (1 bit)
FCHID2 : Fault Protection Trigger on Channel 2
bits : 18 - 18 (1 bit)
FCHID3 : Fault Protection Trigger on Channel 3
bits : 19 - 19 (1 bit)
PWM Channel Dead Time Update Register
address_offset : 0x1C Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
DTHUPD : Dead-Time Value Update for PWMHx Output
bits : 0 - 15 (16 bit)
DTLUPD : Dead-Time Value Update for PWMLx Output
bits : 16 - 31 (16 bit)
PWM Interrupt Status Register 1
address_offset : 0x1C Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
CHID0 : Counter Event on Channel 0
bits : 0 - 0 (1 bit)
CHID1 : Counter Event on Channel 1
bits : 1 - 1 (1 bit)
CHID2 : Counter Event on Channel 2
bits : 2 - 2 (1 bit)
CHID3 : Counter Event on Channel 3
bits : 3 - 3 (1 bit)
FCHID0 : Fault Protection Trigger on Channel 0
bits : 16 - 16 (1 bit)
FCHID1 : Fault Protection Trigger on Channel 1
bits : 17 - 17 (1 bit)
FCHID2 : Fault Protection Trigger on Channel 2
bits : 18 - 18 (1 bit)
FCHID3 : Fault Protection Trigger on Channel 3
bits : 19 - 19 (1 bit)
PWM Channel Dead Time Update Register
address_offset : 0x1C Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
DTHUPD : Dead-Time Value Update for PWMHx Output
bits : 0 - 15 (16 bit)
DTLUPD : Dead-Time Value Update for PWMLx Output
bits : 16 - 31 (16 bit)
PWM Sync Channels Mode Register
address_offset : 0x20 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
SYNC0 : Synchronous Channel 0
bits : 0 - 0 (1 bit)
SYNC1 : Synchronous Channel 1
bits : 1 - 1 (1 bit)
SYNC2 : Synchronous Channel 2
bits : 2 - 2 (1 bit)
SYNC3 : Synchronous Channel 3
bits : 3 - 3 (1 bit)
UPDM : Synchronous Channels Update Mode
bits : 16 - 17 (2 bit)
Enumeration: UPDMSelect
0x0 : MODE0
Manual write of double buffer registers and manual update of synchronous channels
0x1 : MODE1
Manual write of double buffer registers and automatic update of synchronous channels
0x2 : MODE2
Automatic write of duty-cycle update registers by the DMA Controller and automatic update of synchronous channels
End of enumeration elements list.
PTRM : DMA Controller Transfer Request Mode
bits : 20 - 20 (1 bit)
PTRCS : DMA Controller Transfer Request Comparison Selection
bits : 21 - 23 (3 bit)
PWM Sync Channels Mode Register
address_offset : 0x20 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
SYNC0 : Synchronous Channel 0
bits : 0 - 0 (1 bit)
SYNC1 : Synchronous Channel 1
bits : 1 - 1 (1 bit)
SYNC2 : Synchronous Channel 2
bits : 2 - 2 (1 bit)
SYNC3 : Synchronous Channel 3
bits : 3 - 3 (1 bit)
UPDM : Synchronous Channels Update Mode
bits : 16 - 17 (2 bit)
Enumeration: UPDMSelect
0x0 : MODE0
Manual write of double buffer registers and manual update of synchronous channels
0x1 : MODE1
Manual write of double buffer registers and automatic update of synchronous channels
0x2 : MODE2
Automatic write of duty-cycle update registers by the DMA Controller and automatic update of synchronous channels
End of enumeration elements list.
PTRM : DMA Controller Transfer Request Mode
bits : 20 - 20 (1 bit)
PTRCS : DMA Controller Transfer Request Comparison Selection
bits : 21 - 23 (3 bit)
PWM DMA Register
address_offset : 0x24 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
DMADUTY : Duty-Cycle Holding Register for DMA Access
bits : 0 - 23 (24 bit)
PWM DMA Register
address_offset : 0x24 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
DMADUTY : Duty-Cycle Holding Register for DMA Access
bits : 0 - 23 (24 bit)
PWM Sync Channels Update Control Register
address_offset : 0x28 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
UPDULOCK : Synchronous Channels Update Unlock
bits : 0 - 0 (1 bit)
PWM Sync Channels Update Control Register
address_offset : 0x28 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
UPDULOCK : Synchronous Channels Update Unlock
bits : 0 - 0 (1 bit)
PWM Sync Channels Update Period Register
address_offset : 0x2C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
UPR : Update Period
bits : 0 - 3 (4 bit)
UPRCNT : Update Period Counter
bits : 4 - 7 (4 bit)
PWM Sync Channels Update Period Register
address_offset : 0x2C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
UPR : Update Period
bits : 0 - 3 (4 bit)
UPRCNT : Update Period Counter
bits : 4 - 7 (4 bit)
PWM Sync Channels Update Period Update Register
address_offset : 0x30 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
UPRUPD : Update Period Update
bits : 0 - 3 (4 bit)
PWM Sync Channels Update Period Update Register
address_offset : 0x30 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
UPRUPD : Update Period Update
bits : 0 - 3 (4 bit)
PWM Interrupt Enable Register 2
address_offset : 0x34 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
WRDY : Write Ready for Synchronous Channels Update Interrupt Enable
bits : 0 - 0 (1 bit)
UNRE : Synchronous Channels Update Underrun Error Interrupt Enable
bits : 3 - 3 (1 bit)
CMPM0 : Comparison 0 Match Interrupt Enable
bits : 8 - 8 (1 bit)
CMPM1 : Comparison 1 Match Interrupt Enable
bits : 9 - 9 (1 bit)
CMPM2 : Comparison 2 Match Interrupt Enable
bits : 10 - 10 (1 bit)
CMPM3 : Comparison 3 Match Interrupt Enable
bits : 11 - 11 (1 bit)
CMPM4 : Comparison 4 Match Interrupt Enable
bits : 12 - 12 (1 bit)
CMPM5 : Comparison 5 Match Interrupt Enable
bits : 13 - 13 (1 bit)
CMPM6 : Comparison 6 Match Interrupt Enable
bits : 14 - 14 (1 bit)
CMPM7 : Comparison 7 Match Interrupt Enable
bits : 15 - 15 (1 bit)
CMPU0 : Comparison 0 Update Interrupt Enable
bits : 16 - 16 (1 bit)
CMPU1 : Comparison 1 Update Interrupt Enable
bits : 17 - 17 (1 bit)
CMPU2 : Comparison 2 Update Interrupt Enable
bits : 18 - 18 (1 bit)
CMPU3 : Comparison 3 Update Interrupt Enable
bits : 19 - 19 (1 bit)
CMPU4 : Comparison 4 Update Interrupt Enable
bits : 20 - 20 (1 bit)
CMPU5 : Comparison 5 Update Interrupt Enable
bits : 21 - 21 (1 bit)
CMPU6 : Comparison 6 Update Interrupt Enable
bits : 22 - 22 (1 bit)
CMPU7 : Comparison 7 Update Interrupt Enable
bits : 23 - 23 (1 bit)
PWM Interrupt Enable Register 2
address_offset : 0x34 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
WRDY : Write Ready for Synchronous Channels Update Interrupt Enable
bits : 0 - 0 (1 bit)
UNRE : Synchronous Channels Update Underrun Error Interrupt Enable
bits : 3 - 3 (1 bit)
CMPM0 : Comparison 0 Match Interrupt Enable
bits : 8 - 8 (1 bit)
CMPM1 : Comparison 1 Match Interrupt Enable
bits : 9 - 9 (1 bit)
CMPM2 : Comparison 2 Match Interrupt Enable
bits : 10 - 10 (1 bit)
CMPM3 : Comparison 3 Match Interrupt Enable
bits : 11 - 11 (1 bit)
CMPM4 : Comparison 4 Match Interrupt Enable
bits : 12 - 12 (1 bit)
CMPM5 : Comparison 5 Match Interrupt Enable
bits : 13 - 13 (1 bit)
CMPM6 : Comparison 6 Match Interrupt Enable
bits : 14 - 14 (1 bit)
CMPM7 : Comparison 7 Match Interrupt Enable
bits : 15 - 15 (1 bit)
CMPU0 : Comparison 0 Update Interrupt Enable
bits : 16 - 16 (1 bit)
CMPU1 : Comparison 1 Update Interrupt Enable
bits : 17 - 17 (1 bit)
CMPU2 : Comparison 2 Update Interrupt Enable
bits : 18 - 18 (1 bit)
CMPU3 : Comparison 3 Update Interrupt Enable
bits : 19 - 19 (1 bit)
CMPU4 : Comparison 4 Update Interrupt Enable
bits : 20 - 20 (1 bit)
CMPU5 : Comparison 5 Update Interrupt Enable
bits : 21 - 21 (1 bit)
CMPU6 : Comparison 6 Update Interrupt Enable
bits : 22 - 22 (1 bit)
CMPU7 : Comparison 7 Update Interrupt Enable
bits : 23 - 23 (1 bit)
PWM Interrupt Disable Register 2
address_offset : 0x38 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
WRDY : Write Ready for Synchronous Channels Update Interrupt Disable
bits : 0 - 0 (1 bit)
UNRE : Synchronous Channels Update Underrun Error Interrupt Disable
bits : 3 - 3 (1 bit)
CMPM0 : Comparison 0 Match Interrupt Disable
bits : 8 - 8 (1 bit)
CMPM1 : Comparison 1 Match Interrupt Disable
bits : 9 - 9 (1 bit)
CMPM2 : Comparison 2 Match Interrupt Disable
bits : 10 - 10 (1 bit)
CMPM3 : Comparison 3 Match Interrupt Disable
bits : 11 - 11 (1 bit)
CMPM4 : Comparison 4 Match Interrupt Disable
bits : 12 - 12 (1 bit)
CMPM5 : Comparison 5 Match Interrupt Disable
bits : 13 - 13 (1 bit)
CMPM6 : Comparison 6 Match Interrupt Disable
bits : 14 - 14 (1 bit)
CMPM7 : Comparison 7 Match Interrupt Disable
bits : 15 - 15 (1 bit)
CMPU0 : Comparison 0 Update Interrupt Disable
bits : 16 - 16 (1 bit)
CMPU1 : Comparison 1 Update Interrupt Disable
bits : 17 - 17 (1 bit)
CMPU2 : Comparison 2 Update Interrupt Disable
bits : 18 - 18 (1 bit)
CMPU3 : Comparison 3 Update Interrupt Disable
bits : 19 - 19 (1 bit)
CMPU4 : Comparison 4 Update Interrupt Disable
bits : 20 - 20 (1 bit)
CMPU5 : Comparison 5 Update Interrupt Disable
bits : 21 - 21 (1 bit)
CMPU6 : Comparison 6 Update Interrupt Disable
bits : 22 - 22 (1 bit)
CMPU7 : Comparison 7 Update Interrupt Disable
bits : 23 - 23 (1 bit)
PWM Interrupt Disable Register 2
address_offset : 0x38 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
WRDY : Write Ready for Synchronous Channels Update Interrupt Disable
bits : 0 - 0 (1 bit)
UNRE : Synchronous Channels Update Underrun Error Interrupt Disable
bits : 3 - 3 (1 bit)
CMPM0 : Comparison 0 Match Interrupt Disable
bits : 8 - 8 (1 bit)
CMPM1 : Comparison 1 Match Interrupt Disable
bits : 9 - 9 (1 bit)
CMPM2 : Comparison 2 Match Interrupt Disable
bits : 10 - 10 (1 bit)
CMPM3 : Comparison 3 Match Interrupt Disable
bits : 11 - 11 (1 bit)
CMPM4 : Comparison 4 Match Interrupt Disable
bits : 12 - 12 (1 bit)
CMPM5 : Comparison 5 Match Interrupt Disable
bits : 13 - 13 (1 bit)
CMPM6 : Comparison 6 Match Interrupt Disable
bits : 14 - 14 (1 bit)
CMPM7 : Comparison 7 Match Interrupt Disable
bits : 15 - 15 (1 bit)
CMPU0 : Comparison 0 Update Interrupt Disable
bits : 16 - 16 (1 bit)
CMPU1 : Comparison 1 Update Interrupt Disable
bits : 17 - 17 (1 bit)
CMPU2 : Comparison 2 Update Interrupt Disable
bits : 18 - 18 (1 bit)
CMPU3 : Comparison 3 Update Interrupt Disable
bits : 19 - 19 (1 bit)
CMPU4 : Comparison 4 Update Interrupt Disable
bits : 20 - 20 (1 bit)
CMPU5 : Comparison 5 Update Interrupt Disable
bits : 21 - 21 (1 bit)
CMPU6 : Comparison 6 Update Interrupt Disable
bits : 22 - 22 (1 bit)
CMPU7 : Comparison 7 Update Interrupt Disable
bits : 23 - 23 (1 bit)
PWM Interrupt Mask Register 2
address_offset : 0x3C Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
WRDY : Write Ready for Synchronous Channels Update Interrupt Mask
bits : 0 - 0 (1 bit)
UNRE : Synchronous Channels Update Underrun Error Interrupt Mask
bits : 3 - 3 (1 bit)
CMPM0 : Comparison 0 Match Interrupt Mask
bits : 8 - 8 (1 bit)
CMPM1 : Comparison 1 Match Interrupt Mask
bits : 9 - 9 (1 bit)
CMPM2 : Comparison 2 Match Interrupt Mask
bits : 10 - 10 (1 bit)
CMPM3 : Comparison 3 Match Interrupt Mask
bits : 11 - 11 (1 bit)
CMPM4 : Comparison 4 Match Interrupt Mask
bits : 12 - 12 (1 bit)
CMPM5 : Comparison 5 Match Interrupt Mask
bits : 13 - 13 (1 bit)
CMPM6 : Comparison 6 Match Interrupt Mask
bits : 14 - 14 (1 bit)
CMPM7 : Comparison 7 Match Interrupt Mask
bits : 15 - 15 (1 bit)
CMPU0 : Comparison 0 Update Interrupt Mask
bits : 16 - 16 (1 bit)
CMPU1 : Comparison 1 Update Interrupt Mask
bits : 17 - 17 (1 bit)
CMPU2 : Comparison 2 Update Interrupt Mask
bits : 18 - 18 (1 bit)
CMPU3 : Comparison 3 Update Interrupt Mask
bits : 19 - 19 (1 bit)
CMPU4 : Comparison 4 Update Interrupt Mask
bits : 20 - 20 (1 bit)
CMPU5 : Comparison 5 Update Interrupt Mask
bits : 21 - 21 (1 bit)
CMPU6 : Comparison 6 Update Interrupt Mask
bits : 22 - 22 (1 bit)
CMPU7 : Comparison 7 Update Interrupt Mask
bits : 23 - 23 (1 bit)
PWM Interrupt Mask Register 2
address_offset : 0x3C Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
WRDY : Write Ready for Synchronous Channels Update Interrupt Mask
bits : 0 - 0 (1 bit)
UNRE : Synchronous Channels Update Underrun Error Interrupt Mask
bits : 3 - 3 (1 bit)
CMPM0 : Comparison 0 Match Interrupt Mask
bits : 8 - 8 (1 bit)
CMPM1 : Comparison 1 Match Interrupt Mask
bits : 9 - 9 (1 bit)
CMPM2 : Comparison 2 Match Interrupt Mask
bits : 10 - 10 (1 bit)
CMPM3 : Comparison 3 Match Interrupt Mask
bits : 11 - 11 (1 bit)
CMPM4 : Comparison 4 Match Interrupt Mask
bits : 12 - 12 (1 bit)
CMPM5 : Comparison 5 Match Interrupt Mask
bits : 13 - 13 (1 bit)
CMPM6 : Comparison 6 Match Interrupt Mask
bits : 14 - 14 (1 bit)
CMPM7 : Comparison 7 Match Interrupt Mask
bits : 15 - 15 (1 bit)
CMPU0 : Comparison 0 Update Interrupt Mask
bits : 16 - 16 (1 bit)
CMPU1 : Comparison 1 Update Interrupt Mask
bits : 17 - 17 (1 bit)
CMPU2 : Comparison 2 Update Interrupt Mask
bits : 18 - 18 (1 bit)
CMPU3 : Comparison 3 Update Interrupt Mask
bits : 19 - 19 (1 bit)
CMPU4 : Comparison 4 Update Interrupt Mask
bits : 20 - 20 (1 bit)
CMPU5 : Comparison 5 Update Interrupt Mask
bits : 21 - 21 (1 bit)
CMPU6 : Comparison 6 Update Interrupt Mask
bits : 22 - 22 (1 bit)
CMPU7 : Comparison 7 Update Interrupt Mask
bits : 23 - 23 (1 bit)
PWM Enable Register
address_offset : 0x4 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
CHID0 : Channel ID
bits : 0 - 0 (1 bit)
CHID1 : Channel ID
bits : 1 - 1 (1 bit)
CHID2 : Channel ID
bits : 2 - 2 (1 bit)
CHID3 : Channel ID
bits : 3 - 3 (1 bit)
PWM Comparison 0 Value Update Register
address_offset : 0x4 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
CVUPD : Comparison x Value Update
bits : 0 - 23 (24 bit)
CVMUPD : Comparison x Value Mode Update
bits : 24 - 24 (1 bit)
PWM Channel Duty Cycle Register
address_offset : 0x4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
CDTY : Channel Duty-Cycle
bits : 0 - 23 (24 bit)
PWM Enable Register
address_offset : 0x4 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
CHID0 : Channel ID
bits : 0 - 0 (1 bit)
CHID1 : Channel ID
bits : 1 - 1 (1 bit)
CHID2 : Channel ID
bits : 2 - 2 (1 bit)
CHID3 : Channel ID
bits : 3 - 3 (1 bit)
PWM Comparison 0 Value Update Register
address_offset : 0x4 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
CVUPD : Comparison x Value Update
bits : 0 - 23 (24 bit)
CVMUPD : Comparison x Value Mode Update
bits : 24 - 24 (1 bit)
PWM Channel Duty Cycle Register
address_offset : 0x4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
CDTY : Channel Duty-Cycle
bits : 0 - 23 (24 bit)
PWM Interrupt Status Register 2
address_offset : 0x40 Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
WRDY : Write Ready for Synchronous Channels Update
bits : 0 - 0 (1 bit)
UNRE : Synchronous Channels Update Underrun Error
bits : 3 - 3 (1 bit)
CMPM0 : Comparison 0 Match
bits : 8 - 8 (1 bit)
CMPM1 : Comparison 1 Match
bits : 9 - 9 (1 bit)
CMPM2 : Comparison 2 Match
bits : 10 - 10 (1 bit)
CMPM3 : Comparison 3 Match
bits : 11 - 11 (1 bit)
CMPM4 : Comparison 4 Match
bits : 12 - 12 (1 bit)
CMPM5 : Comparison 5 Match
bits : 13 - 13 (1 bit)
CMPM6 : Comparison 6 Match
bits : 14 - 14 (1 bit)
CMPM7 : Comparison 7 Match
bits : 15 - 15 (1 bit)
CMPU0 : Comparison 0 Update
bits : 16 - 16 (1 bit)
CMPU1 : Comparison 1 Update
bits : 17 - 17 (1 bit)
CMPU2 : Comparison 2 Update
bits : 18 - 18 (1 bit)
CMPU3 : Comparison 3 Update
bits : 19 - 19 (1 bit)
CMPU4 : Comparison 4 Update
bits : 20 - 20 (1 bit)
CMPU5 : Comparison 5 Update
bits : 21 - 21 (1 bit)
CMPU6 : Comparison 6 Update
bits : 22 - 22 (1 bit)
CMPU7 : Comparison 7 Update
bits : 23 - 23 (1 bit)
PWM Interrupt Status Register 2
address_offset : 0x40 Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
WRDY : Write Ready for Synchronous Channels Update
bits : 0 - 0 (1 bit)
UNRE : Synchronous Channels Update Underrun Error
bits : 3 - 3 (1 bit)
CMPM0 : Comparison 0 Match
bits : 8 - 8 (1 bit)
CMPM1 : Comparison 1 Match
bits : 9 - 9 (1 bit)
CMPM2 : Comparison 2 Match
bits : 10 - 10 (1 bit)
CMPM3 : Comparison 3 Match
bits : 11 - 11 (1 bit)
CMPM4 : Comparison 4 Match
bits : 12 - 12 (1 bit)
CMPM5 : Comparison 5 Match
bits : 13 - 13 (1 bit)
CMPM6 : Comparison 6 Match
bits : 14 - 14 (1 bit)
CMPM7 : Comparison 7 Match
bits : 15 - 15 (1 bit)
CMPU0 : Comparison 0 Update
bits : 16 - 16 (1 bit)
CMPU1 : Comparison 1 Update
bits : 17 - 17 (1 bit)
CMPU2 : Comparison 2 Update
bits : 18 - 18 (1 bit)
CMPU3 : Comparison 3 Update
bits : 19 - 19 (1 bit)
CMPU4 : Comparison 4 Update
bits : 20 - 20 (1 bit)
CMPU5 : Comparison 5 Update
bits : 21 - 21 (1 bit)
CMPU6 : Comparison 6 Update
bits : 22 - 22 (1 bit)
CMPU7 : Comparison 7 Update
bits : 23 - 23 (1 bit)
PWM Channel Mode Update Register (ch_num = 0)
address_offset : 0x400 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
CPOLUP : Channel Polarity Update
bits : 9 - 9 (1 bit)
CPOLINVUP : Channel Polarity Inversion Update
bits : 13 - 13 (1 bit)
PWM Channel Mode Update Register (ch_num = 0)
address_offset : 0x400 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
CPOLUP : Channel Polarity Update
bits : 9 - 9 (1 bit)
CPOLINVUP : Channel Polarity Inversion Update
bits : 13 - 13 (1 bit)
PWM Channel Mode Update Register (ch_num = 1)
address_offset : 0x420 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
CPOLUP : Channel Polarity Update
bits : 9 - 9 (1 bit)
CPOLINVUP : Channel Polarity Inversion Update
bits : 13 - 13 (1 bit)
PWM Channel Mode Update Register (ch_num = 1)
address_offset : 0x420 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
CPOLUP : Channel Polarity Update
bits : 9 - 9 (1 bit)
CPOLINVUP : Channel Polarity Inversion Update
bits : 13 - 13 (1 bit)
PWM External Trigger Register (trg_num = 1)
address_offset : 0x42C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MAXCNT : Maximum Counter value
bits : 0 - 23 (24 bit)
TRGMODE : External Trigger Mode
bits : 24 - 25 (2 bit)
Enumeration: TRGMODESelect
0x0 : OFF
External trigger is not enabled.
0x1 : MODE1
External PWM Reset Mode
0x2 : MODE2
External PWM Start Mode
0x3 : MODE3
Cycle-by-cycle Duty Mode
End of enumeration elements list.
TRGEDGE : Edge Selection
bits : 28 - 28 (1 bit)
Enumeration: TRGEDGESelect
0 : FALLING_ZERO
TRGMODE = 1: TRGINx event detection on falling edge.TRGMODE = 2, 3: TRGINx active level is 0
1 : RISING_ONE
TRGMODE = 1: TRGINx event detection on rising edge.TRGMODE = 2, 3: TRGINx active level is 1
End of enumeration elements list.
TRGFILT : Filtered input
bits : 29 - 29 (1 bit)
TRGSRC : Trigger Source
bits : 30 - 30 (1 bit)
RFEN : Recoverable Fault Enable
bits : 31 - 31 (1 bit)
PWM External Trigger Register (trg_num = 1)
address_offset : 0x42C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MAXCNT : Maximum Counter value
bits : 0 - 23 (24 bit)
TRGMODE : External Trigger Mode
bits : 24 - 25 (2 bit)
Enumeration: TRGMODESelect
0x0 : OFF
External trigger is not enabled.
0x1 : MODE1
External PWM Reset Mode
0x2 : MODE2
External PWM Start Mode
0x3 : MODE3
Cycle-by-cycle Duty Mode
End of enumeration elements list.
TRGEDGE : Edge Selection
bits : 28 - 28 (1 bit)
Enumeration: TRGEDGESelect
0 : FALLING_ZERO
TRGMODE = 1: TRGINx event detection on falling edge.TRGMODE = 2, 3: TRGINx active level is 0
1 : RISING_ONE
TRGMODE = 1: TRGINx event detection on rising edge.TRGMODE = 2, 3: TRGINx active level is 1
End of enumeration elements list.
TRGFILT : Filtered input
bits : 29 - 29 (1 bit)
TRGSRC : Trigger Source
bits : 30 - 30 (1 bit)
RFEN : Recoverable Fault Enable
bits : 31 - 31 (1 bit)
PWM Leading-Edge Blanking Register (trg_num = 1)
address_offset : 0x430 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
LEBDELAY : Leading-Edge Blanking Delay for TRGINx
bits : 0 - 6 (7 bit)
PWMLFEN : PWML Falling Edge Enable
bits : 16 - 16 (1 bit)
PWMLREN : PWML Rising Edge Enable
bits : 17 - 17 (1 bit)
PWMHFEN : PWMH Falling Edge Enable
bits : 18 - 18 (1 bit)
PWMHREN : PWMH Rising Edge Enable
bits : 19 - 19 (1 bit)
PWM Leading-Edge Blanking Register (trg_num = 1)
address_offset : 0x430 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
LEBDELAY : Leading-Edge Blanking Delay for TRGINx
bits : 0 - 6 (7 bit)
PWMLFEN : PWML Falling Edge Enable
bits : 16 - 16 (1 bit)
PWMLREN : PWML Rising Edge Enable
bits : 17 - 17 (1 bit)
PWMHFEN : PWMH Falling Edge Enable
bits : 18 - 18 (1 bit)
PWMHREN : PWMH Rising Edge Enable
bits : 19 - 19 (1 bit)
PWM Output Override Value Register
address_offset : 0x44 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OOVH0 : Output Override Value for PWMH output of the channel 0
bits : 0 - 0 (1 bit)
OOVH1 : Output Override Value for PWMH output of the channel 1
bits : 1 - 1 (1 bit)
OOVH2 : Output Override Value for PWMH output of the channel 2
bits : 2 - 2 (1 bit)
OOVH3 : Output Override Value for PWMH output of the channel 3
bits : 3 - 3 (1 bit)
OOVL0 : Output Override Value for PWML output of the channel 0
bits : 16 - 16 (1 bit)
OOVL1 : Output Override Value for PWML output of the channel 1
bits : 17 - 17 (1 bit)
OOVL2 : Output Override Value for PWML output of the channel 2
bits : 18 - 18 (1 bit)
OOVL3 : Output Override Value for PWML output of the channel 3
bits : 19 - 19 (1 bit)
PWM Output Override Value Register
address_offset : 0x44 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OOVH0 : Output Override Value for PWMH output of the channel 0
bits : 0 - 0 (1 bit)
OOVH1 : Output Override Value for PWMH output of the channel 1
bits : 1 - 1 (1 bit)
OOVH2 : Output Override Value for PWMH output of the channel 2
bits : 2 - 2 (1 bit)
OOVH3 : Output Override Value for PWMH output of the channel 3
bits : 3 - 3 (1 bit)
OOVL0 : Output Override Value for PWML output of the channel 0
bits : 16 - 16 (1 bit)
OOVL1 : Output Override Value for PWML output of the channel 1
bits : 17 - 17 (1 bit)
OOVL2 : Output Override Value for PWML output of the channel 2
bits : 18 - 18 (1 bit)
OOVL3 : Output Override Value for PWML output of the channel 3
bits : 19 - 19 (1 bit)
PWM Channel Mode Update Register (ch_num = 2)
address_offset : 0x440 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
CPOLUP : Channel Polarity Update
bits : 9 - 9 (1 bit)
CPOLINVUP : Channel Polarity Inversion Update
bits : 13 - 13 (1 bit)
PWM Channel Mode Update Register (ch_num = 2)
address_offset : 0x440 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
CPOLUP : Channel Polarity Update
bits : 9 - 9 (1 bit)
CPOLINVUP : Channel Polarity Inversion Update
bits : 13 - 13 (1 bit)
PWM External Trigger Register (trg_num = 2)
address_offset : 0x44C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MAXCNT : Maximum Counter value
bits : 0 - 23 (24 bit)
TRGMODE : External Trigger Mode
bits : 24 - 25 (2 bit)
Enumeration: TRGMODESelect
0x0 : OFF
External trigger is not enabled.
0x1 : MODE1
External PWM Reset Mode
0x2 : MODE2
External PWM Start Mode
0x3 : MODE3
Cycle-by-cycle Duty Mode
End of enumeration elements list.
TRGEDGE : Edge Selection
bits : 28 - 28 (1 bit)
Enumeration: TRGEDGESelect
0 : FALLING_ZERO
TRGMODE = 1: TRGINx event detection on falling edge.TRGMODE = 2, 3: TRGINx active level is 0
1 : RISING_ONE
TRGMODE = 1: TRGINx event detection on rising edge.TRGMODE = 2, 3: TRGINx active level is 1
End of enumeration elements list.
TRGFILT : Filtered input
bits : 29 - 29 (1 bit)
TRGSRC : Trigger Source
bits : 30 - 30 (1 bit)
RFEN : Recoverable Fault Enable
bits : 31 - 31 (1 bit)
PWM External Trigger Register (trg_num = 2)
address_offset : 0x44C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MAXCNT : Maximum Counter value
bits : 0 - 23 (24 bit)
TRGMODE : External Trigger Mode
bits : 24 - 25 (2 bit)
Enumeration: TRGMODESelect
0x0 : OFF
External trigger is not enabled.
0x1 : MODE1
External PWM Reset Mode
0x2 : MODE2
External PWM Start Mode
0x3 : MODE3
Cycle-by-cycle Duty Mode
End of enumeration elements list.
TRGEDGE : Edge Selection
bits : 28 - 28 (1 bit)
Enumeration: TRGEDGESelect
0 : FALLING_ZERO
TRGMODE = 1: TRGINx event detection on falling edge.TRGMODE = 2, 3: TRGINx active level is 0
1 : RISING_ONE
TRGMODE = 1: TRGINx event detection on rising edge.TRGMODE = 2, 3: TRGINx active level is 1
End of enumeration elements list.
TRGFILT : Filtered input
bits : 29 - 29 (1 bit)
TRGSRC : Trigger Source
bits : 30 - 30 (1 bit)
RFEN : Recoverable Fault Enable
bits : 31 - 31 (1 bit)
PWM Leading-Edge Blanking Register (trg_num = 2)
address_offset : 0x450 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
LEBDELAY : Leading-Edge Blanking Delay for TRGINx
bits : 0 - 6 (7 bit)
PWMLFEN : PWML Falling Edge Enable
bits : 16 - 16 (1 bit)
PWMLREN : PWML Rising Edge Enable
bits : 17 - 17 (1 bit)
PWMHFEN : PWMH Falling Edge Enable
bits : 18 - 18 (1 bit)
PWMHREN : PWMH Rising Edge Enable
bits : 19 - 19 (1 bit)
PWM Leading-Edge Blanking Register (trg_num = 2)
address_offset : 0x450 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
LEBDELAY : Leading-Edge Blanking Delay for TRGINx
bits : 0 - 6 (7 bit)
PWMLFEN : PWML Falling Edge Enable
bits : 16 - 16 (1 bit)
PWMLREN : PWML Rising Edge Enable
bits : 17 - 17 (1 bit)
PWMHFEN : PWMH Falling Edge Enable
bits : 18 - 18 (1 bit)
PWMHREN : PWMH Rising Edge Enable
bits : 19 - 19 (1 bit)
PWM Channel Mode Update Register (ch_num = 3)
address_offset : 0x460 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
CPOLUP : Channel Polarity Update
bits : 9 - 9 (1 bit)
CPOLINVUP : Channel Polarity Inversion Update
bits : 13 - 13 (1 bit)
PWM Channel Mode Update Register (ch_num = 3)
address_offset : 0x460 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
CPOLUP : Channel Polarity Update
bits : 9 - 9 (1 bit)
CPOLINVUP : Channel Polarity Inversion Update
bits : 13 - 13 (1 bit)
PWM Output Selection Register
address_offset : 0x48 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OSH0 : Output Selection for PWMH output of the channel 0
bits : 0 - 0 (1 bit)
OSH1 : Output Selection for PWMH output of the channel 1
bits : 1 - 1 (1 bit)
OSH2 : Output Selection for PWMH output of the channel 2
bits : 2 - 2 (1 bit)
OSH3 : Output Selection for PWMH output of the channel 3
bits : 3 - 3 (1 bit)
OSL0 : Output Selection for PWML output of the channel 0
bits : 16 - 16 (1 bit)
OSL1 : Output Selection for PWML output of the channel 1
bits : 17 - 17 (1 bit)
OSL2 : Output Selection for PWML output of the channel 2
bits : 18 - 18 (1 bit)
OSL3 : Output Selection for PWML output of the channel 3
bits : 19 - 19 (1 bit)
PWM Output Selection Register
address_offset : 0x48 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OSH0 : Output Selection for PWMH output of the channel 0
bits : 0 - 0 (1 bit)
OSH1 : Output Selection for PWMH output of the channel 1
bits : 1 - 1 (1 bit)
OSH2 : Output Selection for PWMH output of the channel 2
bits : 2 - 2 (1 bit)
OSH3 : Output Selection for PWMH output of the channel 3
bits : 3 - 3 (1 bit)
OSL0 : Output Selection for PWML output of the channel 0
bits : 16 - 16 (1 bit)
OSL1 : Output Selection for PWML output of the channel 1
bits : 17 - 17 (1 bit)
OSL2 : Output Selection for PWML output of the channel 2
bits : 18 - 18 (1 bit)
OSL3 : Output Selection for PWML output of the channel 3
bits : 19 - 19 (1 bit)
PWM Output Selection Set Register
address_offset : 0x4C Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
OSSH0 : Output Selection Set for PWMH output of the channel 0
bits : 0 - 0 (1 bit)
OSSH1 : Output Selection Set for PWMH output of the channel 1
bits : 1 - 1 (1 bit)
OSSH2 : Output Selection Set for PWMH output of the channel 2
bits : 2 - 2 (1 bit)
OSSH3 : Output Selection Set for PWMH output of the channel 3
bits : 3 - 3 (1 bit)
OSSL0 : Output Selection Set for PWML output of the channel 0
bits : 16 - 16 (1 bit)
OSSL1 : Output Selection Set for PWML output of the channel 1
bits : 17 - 17 (1 bit)
OSSL2 : Output Selection Set for PWML output of the channel 2
bits : 18 - 18 (1 bit)
OSSL3 : Output Selection Set for PWML output of the channel 3
bits : 19 - 19 (1 bit)
PWM Output Selection Set Register
address_offset : 0x4C Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
OSSH0 : Output Selection Set for PWMH output of the channel 0
bits : 0 - 0 (1 bit)
OSSH1 : Output Selection Set for PWMH output of the channel 1
bits : 1 - 1 (1 bit)
OSSH2 : Output Selection Set for PWMH output of the channel 2
bits : 2 - 2 (1 bit)
OSSH3 : Output Selection Set for PWMH output of the channel 3
bits : 3 - 3 (1 bit)
OSSL0 : Output Selection Set for PWML output of the channel 0
bits : 16 - 16 (1 bit)
OSSL1 : Output Selection Set for PWML output of the channel 1
bits : 17 - 17 (1 bit)
OSSL2 : Output Selection Set for PWML output of the channel 2
bits : 18 - 18 (1 bit)
OSSL3 : Output Selection Set for PWML output of the channel 3
bits : 19 - 19 (1 bit)
PWM Output Selection Clear Register
address_offset : 0x50 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
OSCH0 : Output Selection Clear for PWMH output of the channel 0
bits : 0 - 0 (1 bit)
OSCH1 : Output Selection Clear for PWMH output of the channel 1
bits : 1 - 1 (1 bit)
OSCH2 : Output Selection Clear for PWMH output of the channel 2
bits : 2 - 2 (1 bit)
OSCH3 : Output Selection Clear for PWMH output of the channel 3
bits : 3 - 3 (1 bit)
OSCL0 : Output Selection Clear for PWML output of the channel 0
bits : 16 - 16 (1 bit)
OSCL1 : Output Selection Clear for PWML output of the channel 1
bits : 17 - 17 (1 bit)
OSCL2 : Output Selection Clear for PWML output of the channel 2
bits : 18 - 18 (1 bit)
OSCL3 : Output Selection Clear for PWML output of the channel 3
bits : 19 - 19 (1 bit)
PWM Output Selection Clear Register
address_offset : 0x50 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
OSCH0 : Output Selection Clear for PWMH output of the channel 0
bits : 0 - 0 (1 bit)
OSCH1 : Output Selection Clear for PWMH output of the channel 1
bits : 1 - 1 (1 bit)
OSCH2 : Output Selection Clear for PWMH output of the channel 2
bits : 2 - 2 (1 bit)
OSCH3 : Output Selection Clear for PWMH output of the channel 3
bits : 3 - 3 (1 bit)
OSCL0 : Output Selection Clear for PWML output of the channel 0
bits : 16 - 16 (1 bit)
OSCL1 : Output Selection Clear for PWML output of the channel 1
bits : 17 - 17 (1 bit)
OSCL2 : Output Selection Clear for PWML output of the channel 2
bits : 18 - 18 (1 bit)
OSCL3 : Output Selection Clear for PWML output of the channel 3
bits : 19 - 19 (1 bit)
PWM Output Selection Set Update Register
address_offset : 0x54 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
OSSUPH0 : Output Selection Set for PWMH output of the channel 0
bits : 0 - 0 (1 bit)
OSSUPH1 : Output Selection Set for PWMH output of the channel 1
bits : 1 - 1 (1 bit)
OSSUPH2 : Output Selection Set for PWMH output of the channel 2
bits : 2 - 2 (1 bit)
OSSUPH3 : Output Selection Set for PWMH output of the channel 3
bits : 3 - 3 (1 bit)
OSSUPL0 : Output Selection Set for PWML output of the channel 0
bits : 16 - 16 (1 bit)
OSSUPL1 : Output Selection Set for PWML output of the channel 1
bits : 17 - 17 (1 bit)
OSSUPL2 : Output Selection Set for PWML output of the channel 2
bits : 18 - 18 (1 bit)
OSSUPL3 : Output Selection Set for PWML output of the channel 3
bits : 19 - 19 (1 bit)
PWM Output Selection Set Update Register
address_offset : 0x54 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
OSSUPH0 : Output Selection Set for PWMH output of the channel 0
bits : 0 - 0 (1 bit)
OSSUPH1 : Output Selection Set for PWMH output of the channel 1
bits : 1 - 1 (1 bit)
OSSUPH2 : Output Selection Set for PWMH output of the channel 2
bits : 2 - 2 (1 bit)
OSSUPH3 : Output Selection Set for PWMH output of the channel 3
bits : 3 - 3 (1 bit)
OSSUPL0 : Output Selection Set for PWML output of the channel 0
bits : 16 - 16 (1 bit)
OSSUPL1 : Output Selection Set for PWML output of the channel 1
bits : 17 - 17 (1 bit)
OSSUPL2 : Output Selection Set for PWML output of the channel 2
bits : 18 - 18 (1 bit)
OSSUPL3 : Output Selection Set for PWML output of the channel 3
bits : 19 - 19 (1 bit)
PWM Output Selection Clear Update Register
address_offset : 0x58 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
OSCUPH0 : Output Selection Clear for PWMH output of the channel 0
bits : 0 - 0 (1 bit)
OSCUPH1 : Output Selection Clear for PWMH output of the channel 1
bits : 1 - 1 (1 bit)
OSCUPH2 : Output Selection Clear for PWMH output of the channel 2
bits : 2 - 2 (1 bit)
OSCUPH3 : Output Selection Clear for PWMH output of the channel 3
bits : 3 - 3 (1 bit)
OSCUPL0 : Output Selection Clear for PWML output of the channel 0
bits : 16 - 16 (1 bit)
OSCUPL1 : Output Selection Clear for PWML output of the channel 1
bits : 17 - 17 (1 bit)
OSCUPL2 : Output Selection Clear for PWML output of the channel 2
bits : 18 - 18 (1 bit)
OSCUPL3 : Output Selection Clear for PWML output of the channel 3
bits : 19 - 19 (1 bit)
PWM Output Selection Clear Update Register
address_offset : 0x58 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
OSCUPH0 : Output Selection Clear for PWMH output of the channel 0
bits : 0 - 0 (1 bit)
OSCUPH1 : Output Selection Clear for PWMH output of the channel 1
bits : 1 - 1 (1 bit)
OSCUPH2 : Output Selection Clear for PWMH output of the channel 2
bits : 2 - 2 (1 bit)
OSCUPH3 : Output Selection Clear for PWMH output of the channel 3
bits : 3 - 3 (1 bit)
OSCUPL0 : Output Selection Clear for PWML output of the channel 0
bits : 16 - 16 (1 bit)
OSCUPL1 : Output Selection Clear for PWML output of the channel 1
bits : 17 - 17 (1 bit)
OSCUPL2 : Output Selection Clear for PWML output of the channel 2
bits : 18 - 18 (1 bit)
OSCUPL3 : Output Selection Clear for PWML output of the channel 3
bits : 19 - 19 (1 bit)
PWM Fault Mode Register
address_offset : 0x5C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FPOL : Fault Polarity
bits : 0 - 7 (8 bit)
FMOD : Fault Activation Mode
bits : 8 - 15 (8 bit)
FFIL : Fault Filtering
bits : 16 - 23 (8 bit)
PWM Fault Mode Register
address_offset : 0x5C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FPOL : Fault Polarity
bits : 0 - 7 (8 bit)
FMOD : Fault Activation Mode
bits : 8 - 15 (8 bit)
FFIL : Fault Filtering
bits : 16 - 23 (8 bit)
PWM Fault Status Register
address_offset : 0x60 Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
FIV : Fault Input Value
bits : 0 - 7 (8 bit)
FS : Fault Status
bits : 8 - 15 (8 bit)
PWM Fault Status Register
address_offset : 0x60 Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
FIV : Fault Input Value
bits : 0 - 7 (8 bit)
FS : Fault Status
bits : 8 - 15 (8 bit)
PWM Fault Clear Register
address_offset : 0x64 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
FCLR : Fault Clear
bits : 0 - 7 (8 bit)
PWM Fault Clear Register
address_offset : 0x64 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
FCLR : Fault Clear
bits : 0 - 7 (8 bit)
PWM Fault Protection Value Register 1
address_offset : 0x68 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FPVH0 : Fault Protection Value for PWMH output on channel 0
bits : 0 - 0 (1 bit)
FPVH1 : Fault Protection Value for PWMH output on channel 1
bits : 1 - 1 (1 bit)
FPVH2 : Fault Protection Value for PWMH output on channel 2
bits : 2 - 2 (1 bit)
FPVH3 : Fault Protection Value for PWMH output on channel 3
bits : 3 - 3 (1 bit)
FPVL0 : Fault Protection Value for PWML output on channel 0
bits : 16 - 16 (1 bit)
FPVL1 : Fault Protection Value for PWML output on channel 1
bits : 17 - 17 (1 bit)
FPVL2 : Fault Protection Value for PWML output on channel 2
bits : 18 - 18 (1 bit)
FPVL3 : Fault Protection Value for PWML output on channel 3
bits : 19 - 19 (1 bit)
PWM Fault Protection Value Register 1
address_offset : 0x68 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FPVH0 : Fault Protection Value for PWMH output on channel 0
bits : 0 - 0 (1 bit)
FPVH1 : Fault Protection Value for PWMH output on channel 1
bits : 1 - 1 (1 bit)
FPVH2 : Fault Protection Value for PWMH output on channel 2
bits : 2 - 2 (1 bit)
FPVH3 : Fault Protection Value for PWMH output on channel 3
bits : 3 - 3 (1 bit)
FPVL0 : Fault Protection Value for PWML output on channel 0
bits : 16 - 16 (1 bit)
FPVL1 : Fault Protection Value for PWML output on channel 1
bits : 17 - 17 (1 bit)
FPVL2 : Fault Protection Value for PWML output on channel 2
bits : 18 - 18 (1 bit)
FPVL3 : Fault Protection Value for PWML output on channel 3
bits : 19 - 19 (1 bit)
PWM Fault Protection Enable Register
address_offset : 0x6C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FPE0 : Fault Protection Enable for channel 0
bits : 0 - 7 (8 bit)
FPE1 : Fault Protection Enable for channel 1
bits : 8 - 15 (8 bit)
FPE2 : Fault Protection Enable for channel 2
bits : 16 - 23 (8 bit)
FPE3 : Fault Protection Enable for channel 3
bits : 24 - 31 (8 bit)
PWM Fault Protection Enable Register
address_offset : 0x6C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FPE0 : Fault Protection Enable for channel 0
bits : 0 - 7 (8 bit)
FPE1 : Fault Protection Enable for channel 1
bits : 8 - 15 (8 bit)
FPE2 : Fault Protection Enable for channel 2
bits : 16 - 23 (8 bit)
FPE3 : Fault Protection Enable for channel 3
bits : 24 - 31 (8 bit)
PWM Event Line 0 Mode Register 0
address_offset : 0x7C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
CSEL0 : Comparison 0 Selection
bits : 0 - 0 (1 bit)
CSEL1 : Comparison 1 Selection
bits : 1 - 1 (1 bit)
CSEL2 : Comparison 2 Selection
bits : 2 - 2 (1 bit)
CSEL3 : Comparison 3 Selection
bits : 3 - 3 (1 bit)
CSEL4 : Comparison 4 Selection
bits : 4 - 4 (1 bit)
CSEL5 : Comparison 5 Selection
bits : 5 - 5 (1 bit)
CSEL6 : Comparison 6 Selection
bits : 6 - 6 (1 bit)
CSEL7 : Comparison 7 Selection
bits : 7 - 7 (1 bit)
PWM Event Line 0 Mode Register 0
address_offset : 0x7C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
CSEL0 : Comparison 0 Selection
bits : 0 - 0 (1 bit)
CSEL1 : Comparison 1 Selection
bits : 1 - 1 (1 bit)
CSEL2 : Comparison 2 Selection
bits : 2 - 2 (1 bit)
CSEL3 : Comparison 3 Selection
bits : 3 - 3 (1 bit)
CSEL4 : Comparison 4 Selection
bits : 4 - 4 (1 bit)
CSEL5 : Comparison 5 Selection
bits : 5 - 5 (1 bit)
CSEL6 : Comparison 6 Selection
bits : 6 - 6 (1 bit)
CSEL7 : Comparison 7 Selection
bits : 7 - 7 (1 bit)
PWM Disable Register
address_offset : 0x8 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
CHID0 : Channel ID
bits : 0 - 0 (1 bit)
CHID1 : Channel ID
bits : 1 - 1 (1 bit)
CHID2 : Channel ID
bits : 2 - 2 (1 bit)
CHID3 : Channel ID
bits : 3 - 3 (1 bit)
PWM Comparison 0 Mode Register
address_offset : 0x8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
CEN : Comparison x Enable
bits : 0 - 0 (1 bit)
CTR : Comparison x Trigger
bits : 4 - 7 (4 bit)
CPR : Comparison x Period
bits : 8 - 11 (4 bit)
CPRCNT : Comparison x Period Counter
bits : 12 - 15 (4 bit)
CUPR : Comparison x Update Period
bits : 16 - 19 (4 bit)
CUPRCNT : Comparison x Update Period Counter
bits : 20 - 23 (4 bit)
PWM Channel Duty Cycle Update Register
address_offset : 0x8 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
CDTYUPD : Channel Duty-Cycle Update
bits : 0 - 23 (24 bit)
PWM Disable Register
address_offset : 0x8 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
CHID0 : Channel ID
bits : 0 - 0 (1 bit)
CHID1 : Channel ID
bits : 1 - 1 (1 bit)
CHID2 : Channel ID
bits : 2 - 2 (1 bit)
CHID3 : Channel ID
bits : 3 - 3 (1 bit)
PWM Comparison 0 Mode Register
address_offset : 0x8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
CEN : Comparison x Enable
bits : 0 - 0 (1 bit)
CTR : Comparison x Trigger
bits : 4 - 7 (4 bit)
CPR : Comparison x Period
bits : 8 - 11 (4 bit)
CPRCNT : Comparison x Period Counter
bits : 12 - 15 (4 bit)
CUPR : Comparison x Update Period
bits : 16 - 19 (4 bit)
CUPRCNT : Comparison x Update Period Counter
bits : 20 - 23 (4 bit)
PWM Channel Duty Cycle Update Register
address_offset : 0x8 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
CDTYUPD : Channel Duty-Cycle Update
bits : 0 - 23 (24 bit)
PWM Event Line 0 Mode Register 0
address_offset : 0x80 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
CSEL0 : Comparison 0 Selection
bits : 0 - 0 (1 bit)
CSEL1 : Comparison 1 Selection
bits : 1 - 1 (1 bit)
CSEL2 : Comparison 2 Selection
bits : 2 - 2 (1 bit)
CSEL3 : Comparison 3 Selection
bits : 3 - 3 (1 bit)
CSEL4 : Comparison 4 Selection
bits : 4 - 4 (1 bit)
CSEL5 : Comparison 5 Selection
bits : 5 - 5 (1 bit)
CSEL6 : Comparison 6 Selection
bits : 6 - 6 (1 bit)
CSEL7 : Comparison 7 Selection
bits : 7 - 7 (1 bit)
PWM Event Line 0 Mode Register 0
address_offset : 0x80 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
CSEL0 : Comparison 0 Selection
bits : 0 - 0 (1 bit)
CSEL1 : Comparison 1 Selection
bits : 1 - 1 (1 bit)
CSEL2 : Comparison 2 Selection
bits : 2 - 2 (1 bit)
CSEL3 : Comparison 3 Selection
bits : 3 - 3 (1 bit)
CSEL4 : Comparison 4 Selection
bits : 4 - 4 (1 bit)
CSEL5 : Comparison 5 Selection
bits : 5 - 5 (1 bit)
CSEL6 : Comparison 6 Selection
bits : 6 - 6 (1 bit)
CSEL7 : Comparison 7 Selection
bits : 7 - 7 (1 bit)
PWM Spread Spectrum Register
address_offset : 0xA0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
SPRD : Spread Spectrum Limit Value
bits : 0 - 23 (24 bit)
SPRDM : Spread Spectrum Counter Mode
bits : 24 - 24 (1 bit)
PWM Spread Spectrum Register
address_offset : 0xA0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
SPRD : Spread Spectrum Limit Value
bits : 0 - 23 (24 bit)
SPRDM : Spread Spectrum Counter Mode
bits : 24 - 24 (1 bit)
PWM Spread Spectrum Update Register
address_offset : 0xA4 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
SPRDUP : Spread Spectrum Limit Value Update
bits : 0 - 23 (24 bit)
PWM Spread Spectrum Update Register
address_offset : 0xA4 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
SPRDUP : Spread Spectrum Limit Value Update
bits : 0 - 23 (24 bit)
PWM Stepper Motor Mode Register
address_offset : 0xB0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
GCEN0 : Gray Count ENable
bits : 0 - 0 (1 bit)
GCEN1 : Gray Count ENable
bits : 1 - 1 (1 bit)
DOWN0 : DOWN Count
bits : 16 - 16 (1 bit)
DOWN1 : DOWN Count
bits : 17 - 17 (1 bit)
PWM Stepper Motor Mode Register
address_offset : 0xB0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
GCEN0 : Gray Count ENable
bits : 0 - 0 (1 bit)
GCEN1 : Gray Count ENable
bits : 1 - 1 (1 bit)
DOWN0 : DOWN Count
bits : 16 - 16 (1 bit)
DOWN1 : DOWN Count
bits : 17 - 17 (1 bit)
PWM Status Register
address_offset : 0xC Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
CHID0 : Channel ID
bits : 0 - 0 (1 bit)
CHID1 : Channel ID
bits : 1 - 1 (1 bit)
CHID2 : Channel ID
bits : 2 - 2 (1 bit)
CHID3 : Channel ID
bits : 3 - 3 (1 bit)
PWM Comparison 0 Mode Update Register
address_offset : 0xC Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
CENUPD : Comparison x Enable Update
bits : 0 - 0 (1 bit)
CTRUPD : Comparison x Trigger Update
bits : 4 - 7 (4 bit)
CPRUPD : Comparison x Period Update
bits : 8 - 11 (4 bit)
CUPRUPD : Comparison x Update Period Update
bits : 16 - 19 (4 bit)
PWM Channel Period Register
address_offset : 0xC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
CPRD : Channel Period
bits : 0 - 23 (24 bit)
PWM Status Register
address_offset : 0xC Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
CHID0 : Channel ID
bits : 0 - 0 (1 bit)
CHID1 : Channel ID
bits : 1 - 1 (1 bit)
CHID2 : Channel ID
bits : 2 - 2 (1 bit)
CHID3 : Channel ID
bits : 3 - 3 (1 bit)
PWM Comparison 0 Mode Update Register
address_offset : 0xC Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
CENUPD : Comparison x Enable Update
bits : 0 - 0 (1 bit)
CTRUPD : Comparison x Trigger Update
bits : 4 - 7 (4 bit)
CPRUPD : Comparison x Period Update
bits : 8 - 11 (4 bit)
CUPRUPD : Comparison x Update Period Update
bits : 16 - 19 (4 bit)
PWM Channel Period Register
address_offset : 0xC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
CPRD : Channel Period
bits : 0 - 23 (24 bit)
PWM Fault Protection Value 2 Register
address_offset : 0xC0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FPZH0 : Fault Protection to Hi-Z for PWMH output on channel 0
bits : 0 - 0 (1 bit)
FPZH1 : Fault Protection to Hi-Z for PWMH output on channel 1
bits : 1 - 1 (1 bit)
FPZH2 : Fault Protection to Hi-Z for PWMH output on channel 2
bits : 2 - 2 (1 bit)
FPZH3 : Fault Protection to Hi-Z for PWMH output on channel 3
bits : 3 - 3 (1 bit)
FPZL0 : Fault Protection to Hi-Z for PWML output on channel 0
bits : 16 - 16 (1 bit)
FPZL1 : Fault Protection to Hi-Z for PWML output on channel 1
bits : 17 - 17 (1 bit)
FPZL2 : Fault Protection to Hi-Z for PWML output on channel 2
bits : 18 - 18 (1 bit)
FPZL3 : Fault Protection to Hi-Z for PWML output on channel 3
bits : 19 - 19 (1 bit)
PWM Fault Protection Value 2 Register
address_offset : 0xC0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FPZH0 : Fault Protection to Hi-Z for PWMH output on channel 0
bits : 0 - 0 (1 bit)
FPZH1 : Fault Protection to Hi-Z for PWMH output on channel 1
bits : 1 - 1 (1 bit)
FPZH2 : Fault Protection to Hi-Z for PWMH output on channel 2
bits : 2 - 2 (1 bit)
FPZH3 : Fault Protection to Hi-Z for PWMH output on channel 3
bits : 3 - 3 (1 bit)
FPZL0 : Fault Protection to Hi-Z for PWML output on channel 0
bits : 16 - 16 (1 bit)
FPZL1 : Fault Protection to Hi-Z for PWML output on channel 1
bits : 17 - 17 (1 bit)
FPZL2 : Fault Protection to Hi-Z for PWML output on channel 2
bits : 18 - 18 (1 bit)
FPZL3 : Fault Protection to Hi-Z for PWML output on channel 3
bits : 19 - 19 (1 bit)
PWM Write Protection Control Register
address_offset : 0xE4 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
WPCMD : Write Protection Command
bits : 0 - 1 (2 bit)
Enumeration: WPCMDSelect
0x0 : DISABLE_SW_PROT
Disables the software write protection of the register groups of which the bit WPRGx is at '1'.
0x1 : ENABLE_SW_PROT
Enables the software write protection of the register groups of which the bit WPRGx is at '1'.
0x2 : ENABLE_HW_PROT
Enables the hardware write protection of the register groups of which the bit WPRGx is at '1'. Only a hardware reset of the PWM controller can disable the hardware write protection. Moreover, to meet security requirements, the PIO lines associated with the PWM can not be configured through the PIO interface.
End of enumeration elements list.
WPRG0 : Write Protection Register Group 0
bits : 2 - 2 (1 bit)
WPRG1 : Write Protection Register Group 1
bits : 3 - 3 (1 bit)
WPRG2 : Write Protection Register Group 2
bits : 4 - 4 (1 bit)
WPRG3 : Write Protection Register Group 3
bits : 5 - 5 (1 bit)
WPRG4 : Write Protection Register Group 4
bits : 6 - 6 (1 bit)
WPRG5 : Write Protection Register Group 5
bits : 7 - 7 (1 bit)
WPKEY : Write Protection Key
bits : 8 - 31 (24 bit)
Enumeration: WPKEYSelect
0x50574D : PASSWD
Writing any other value in this field aborts the write operation of the WPCMD field.Always reads as 0
End of enumeration elements list.
PWM Write Protection Control Register
address_offset : 0xE4 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
WPCMD : Write Protection Command
bits : 0 - 1 (2 bit)
Enumeration: WPCMDSelect
0x0 : DISABLE_SW_PROT
Disables the software write protection of the register groups of which the bit WPRGx is at '1'.
0x1 : ENABLE_SW_PROT
Enables the software write protection of the register groups of which the bit WPRGx is at '1'.
0x2 : ENABLE_HW_PROT
Enables the hardware write protection of the register groups of which the bit WPRGx is at '1'. Only a hardware reset of the PWM controller can disable the hardware write protection. Moreover, to meet security requirements, the PIO lines associated with the PWM can not be configured through the PIO interface.
End of enumeration elements list.
WPRG0 : Write Protection Register Group 0
bits : 2 - 2 (1 bit)
WPRG1 : Write Protection Register Group 1
bits : 3 - 3 (1 bit)
WPRG2 : Write Protection Register Group 2
bits : 4 - 4 (1 bit)
WPRG3 : Write Protection Register Group 3
bits : 5 - 5 (1 bit)
WPRG4 : Write Protection Register Group 4
bits : 6 - 6 (1 bit)
WPRG5 : Write Protection Register Group 5
bits : 7 - 7 (1 bit)
WPKEY : Write Protection Key
bits : 8 - 31 (24 bit)
Enumeration: WPKEYSelect
0x50574D : PASSWD
Writing any other value in this field aborts the write operation of the WPCMD field.Always reads as 0
End of enumeration elements list.
PWM Write Protection Status Register
address_offset : 0xE8 Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
WPSWS0 : Write Protect SW Status
bits : 0 - 0 (1 bit)
WPSWS1 : Write Protect SW Status
bits : 1 - 1 (1 bit)
WPSWS2 : Write Protect SW Status
bits : 2 - 2 (1 bit)
WPSWS3 : Write Protect SW Status
bits : 3 - 3 (1 bit)
WPSWS4 : Write Protect SW Status
bits : 4 - 4 (1 bit)
WPSWS5 : Write Protect SW Status
bits : 5 - 5 (1 bit)
WPVS : Write Protect Violation Status
bits : 7 - 7 (1 bit)
WPHWS0 : Write Protect HW Status
bits : 8 - 8 (1 bit)
WPHWS1 : Write Protect HW Status
bits : 9 - 9 (1 bit)
WPHWS2 : Write Protect HW Status
bits : 10 - 10 (1 bit)
WPHWS3 : Write Protect HW Status
bits : 11 - 11 (1 bit)
WPHWS4 : Write Protect HW Status
bits : 12 - 12 (1 bit)
WPHWS5 : Write Protect HW Status
bits : 13 - 13 (1 bit)
WPVSRC : Write Protect Violation Source
bits : 16 - 31 (16 bit)
PWM Write Protection Status Register
address_offset : 0xE8 Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
WPSWS0 : Write Protect SW Status
bits : 0 - 0 (1 bit)
WPSWS1 : Write Protect SW Status
bits : 1 - 1 (1 bit)
WPSWS2 : Write Protect SW Status
bits : 2 - 2 (1 bit)
WPSWS3 : Write Protect SW Status
bits : 3 - 3 (1 bit)
WPSWS4 : Write Protect SW Status
bits : 4 - 4 (1 bit)
WPSWS5 : Write Protect SW Status
bits : 5 - 5 (1 bit)
WPVS : Write Protect Violation Status
bits : 7 - 7 (1 bit)
WPHWS0 : Write Protect HW Status
bits : 8 - 8 (1 bit)
WPHWS1 : Write Protect HW Status
bits : 9 - 9 (1 bit)
WPHWS2 : Write Protect HW Status
bits : 10 - 10 (1 bit)
WPHWS3 : Write Protect HW Status
bits : 11 - 11 (1 bit)
WPHWS4 : Write Protect HW Status
bits : 12 - 12 (1 bit)
WPHWS5 : Write Protect HW Status
bits : 13 - 13 (1 bit)
WPVSRC : Write Protect Violation Source
bits : 16 - 31 (16 bit)
Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !
This website is sponsored by Embeetle, an IDE designed from scratch for embedded software developers.