\n
address_offset : 0x0 Bytes (0x0)
size : 0x1000 byte (0x0)
mem_usage : registers
protection :
Fetcher: Start address of data block. In direct mode, this register is written by the software. In scatter-gather mode, this register is updated after each processed descriptor.
address_offset : 0x0 Bytes (0x0)
size : -1 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
ADDR : Start address of data block
bits : 0 - 31 (32 bit)
access : read-write
Pusher: Start address of data block (LSB). In direct mode, this register is written by the software. In scatter-gather mode, this register is updated after each processed descriptor.
address_offset : 0x10 Bytes (0x0)
size : -1 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
ADDR : Start address of data block
bits : 0 - 31 (32 bit)
access : read-write
Pusher: Length of data block. In direct mode, this register is written by the software. In scatter-gather mode, this register is not used.
address_offset : 0x18 Bytes (0x0)
size : -1 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
LENGTH : Start address of data block
bits : 0 - 27 (28 bit)
access : read-write
CONSTADDR : Constant address
bits : 28 - 28 (1 bit)
access : read-write
REALIGN : Realign length
bits : 29 - 29 (1 bit)
access : read-write
DISCARD : Discard data
bits : 30 - 30 (1 bit)
access : read-write
Interrupt enable
address_offset : 0x1C Bytes (0x0)
size : -1 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FETCHERENDOFBLOCK : End of block interrupt enable
bits : 0 - 0 (1 bit)
access : read-write
FETCHERSTOPPED : Stopped interrupt enable
bits : 1 - 1 (1 bit)
access : read-write
FETCHERERROR : Error interrupt enable
bits : 2 - 2 (1 bit)
access : read-write
PUSHERENDOFBLOCK : End of block interrupt enable
bits : 3 - 3 (1 bit)
access : read-write
PUSHERSTOPPED : Stopped interrupt enable
bits : 4 - 4 (1 bit)
access : read-write
PUSHERERROR : Error interrupt enable
bits : 5 - 5 (1 bit)
access : read-write
Interrupt flag register
address_offset : 0x28 Bytes (0x0)
size : -1 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
FETCHERENDOFBLOCK : End of block interrupt flag
bits : 0 - 0 (1 bit)
access : read-only
FETCHERSTOPPED : Stopped interrupt flag
bits : 1 - 1 (1 bit)
access : read-only
FETCHERERROR : Error interrupt flag
bits : 2 - 2 (1 bit)
access : read-only
PUSHERENDOFBLOCK : End of block interrupt flag
bits : 3 - 3 (1 bit)
access : read-only
PUSHERSTOPPED : Stopped interrupt flag
bits : 4 - 4 (1 bit)
access : read-only
PUSHERERROR : Error interrupt flag
bits : 5 - 5 (1 bit)
access : read-only
Writing a '1' clears the interrupt status. Writing a '0' has no effect.
address_offset : 0x30 Bytes (0x0)
size : -1 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
FETCHERENDOFBLOCK : End of block interrupt flag clear
bits : 0 - 0 (1 bit)
access : write-only
FETCHERSTOPPED : Stopped interrupt flag clear
bits : 1 - 1 (1 bit)
access : write-only
FETCHERERROR : Error interrupt flag clear
bits : 2 - 2 (1 bit)
access : write-only
PUSHERENDOFBLOCK : FETCHERENDOFBLOCKIFC
bits : 3 - 3 (1 bit)
access : write-only
PUSHERSTOPPED : FETCHERSTOPPEDIFC
bits : 4 - 4 (1 bit)
access : write-only
PUSHERERROR : FETCHERERRORIFC
bits : 5 - 5 (1 bit)
access : write-only
Control register, called CONFIG in Barco datasheet.
address_offset : 0x34 Bytes (0x0)
size : -1 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FETCHERSCATTERGATHER : Fetcher scatter/gather
bits : 0 - 0 (1 bit)
access : read-write
PUSHERSCATTERGATHER : Pusher scatter/gather
bits : 1 - 1 (1 bit)
access : read-write
STOPFETCHER : Stop fetcher
bits : 2 - 2 (1 bit)
access : read-write
STOPPUSHER : Stop pusher
bits : 3 - 3 (1 bit)
access : read-write
SWRESET : Software reset
bits : 4 - 4 (1 bit)
access : read-write
Command register for starting the fetcher and pusher
address_offset : 0x38 Bytes (0x0)
size : -1 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
STARTFETCHER : Start fetch
bits : 0 - 0 (1 bit)
access : write-only
STARTPUSHER : Start push
bits : 1 - 1 (1 bit)
access : write-only
Status register
address_offset : 0x3C Bytes (0x0)
size : -1 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
FETCHERBSY : Fetcher busy
bits : 0 - 0 (1 bit)
access : read-only
PUSHERBSY : Pusher busy
bits : 1 - 1 (1 bit)
access : read-only
NOTEMPTY : Not empty flag from input FIFO (fetcher)
bits : 4 - 4 (1 bit)
access : read-only
WAITING : Pusher waiting for FIFO
bits : 5 - 5 (1 bit)
access : read-only
SOFTRSTBSY : Software reset busy
bits : 6 - 6 (1 bit)
access : read-only
FIFODATANUM : Number of data in output FIFO
bits : 16 - 31 (16 bit)
access : read-only
No Description
address_offset : 0x400 Bytes (0x0)
size : -1 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
g_IncludeAES : Generic g_IncludeAES value
bits : 0 - 0 (1 bit)
access : read-only
g_IncludeAESGCM : Generic g_IncludeAESGCM value
bits : 1 - 1 (1 bit)
access : read-only
g_IncludeAESXTS : Generic g_IncludeAESXTS value
bits : 2 - 2 (1 bit)
access : read-only
g_IncludeDES : Generic g_IncludeDES value
bits : 3 - 3 (1 bit)
access : read-only
g_IncludeHASH : Generic g_IncludeHASH value
bits : 4 - 4 (1 bit)
access : read-only
g_IncludeChachaPoly : Generic g_IncludeChachaPoly value
bits : 5 - 5 (1 bit)
access : read-only
g_IncludeSHA3 : Generic g_IncludeSHA3 value
bits : 6 - 6 (1 bit)
access : read-only
g_IncludeZUC : Generic g_IncludeZUC value
bits : 7 - 7 (1 bit)
access : read-only
g_IncludeSM4 : Generic g_IncludeSM4 value
bits : 8 - 8 (1 bit)
access : read-only
g_IncludePKE : Generic g_IncludePKE value
bits : 9 - 9 (1 bit)
access : read-only
g_IncludeNDRNG : Generic g_IncludeNDRNG value
bits : 10 - 10 (1 bit)
access : read-only
No Description
address_offset : 0x404 Bytes (0x0)
size : -1 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
g_AesModesPoss : AES Modes Supported
bits : 0 - 8 (9 bit)
access : read-only
g_CS : Generic g_CS value
bits : 16 - 16 (1 bit)
access : read-only
g_UseMasking : Generic g_UseMasking value
bits : 17 - 17 (1 bit)
access : read-only
g_Keysize : Generic g_Keysize value
bits : 24 - 26 (3 bit)
access : read-only
No Description
address_offset : 0x408 Bytes (0x0)
size : -1 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
g_CtrSize : Generic g_CtrSize value
bits : 0 - 15 (16 bit)
access : read-only
No Description
address_offset : 0x40C Bytes (0x0)
size : -1 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
g_HashMaskFunc : Generic g_HashMaskFunc value
bits : 0 - 6 (7 bit)
access : read-only
g_HashPadding : Generic g_HashPadding value
bits : 16 - 16 (1 bit)
access : read-only
g_HMAC_enabled : Generic g_HMAC_enabled value
bits : 17 - 17 (1 bit)
access : read-only
g_HashVerifyDigest : Generic g_HashVerifyDigest value
bits : 18 - 18 (1 bit)
access : read-only
No Description
address_offset : 0x410 Bytes (0x0)
size : -1 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
g_Sha3CtxtEn : Generic g_Sha3CtxtEn value
bits : 0 - 0 (1 bit)
access : read-only
No Description
address_offset : 0x414 Bytes (0x0)
size : -1 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
g_SM4ModesPoss : Generic g_SM4ModesPoss value
bits : 0 - 6 (7 bit)
access : read-only
Fetcher: Length of data block. In direct mode, this register is written by the software. In scatter-gather mode, this register is not used.
address_offset : 0x8 Bytes (0x0)
size : -1 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
LENGTH : Length of data block
bits : 0 - 27 (28 bit)
access : read-write
CONSTADDR : Constant address
bits : 28 - 28 (1 bit)
access : read-write
REALIGN : Realign lengh
bits : 29 - 29 (1 bit)
access : read-write
Fetcher: User tag. In direct mode, this register is written by the software. In scatter-gather mode, this register is not used.
address_offset : 0xC Bytes (0x0)
size : -1 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TAG : User tag
bits : 0 - 31 (32 bit)
access : read-write
Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !
This website is sponsored by Embeetle, an IDE designed from scratch for embedded software developers.