\n

RTC

Peripheral Memory Blocks

address_offset : 0x0 Bytes (0x0)
size : 0x1 byte (0x0)
mem_usage : registers
protection : not protected

address_offset : 0x2 Bytes (0x0)
size : 0x8 byte (0x0)
mem_usage : registers
protection : not protected

address_offset : 0xA Bytes (0x0)
size : 0x1 byte (0x0)
mem_usage : registers
protection : not protected

address_offset : 0xC Bytes (0x0)
size : 0x1 byte (0x0)
mem_usage : registers
protection : not protected

address_offset : 0xE Bytes (0x0)
size : 0xA byte (0x0)
mem_usage : registers
protection : not protected

address_offset : 0x18 Bytes (0x0)
size : 0x4 byte (0x0)
mem_usage : registers
protection : not protected

address_offset : 0x1C Bytes (0x0)
size : 0x3 byte (0x0)
mem_usage : registers
protection : not protected

address_offset : 0x22 Bytes (0x0)
size : 0x1 byte (0x0)
mem_usage : registers
protection : not protected

address_offset : 0x24 Bytes (0x0)
size : 0x1 byte (0x0)
mem_usage : registers
protection : not protected

address_offset : 0x28 Bytes (0x0)
size : 0x1 byte (0x0)
mem_usage : registers
protection : not protected

address_offset : 0x2A Bytes (0x0)
size : 0x5 byte (0x0)
mem_usage : registers
protection : not protected

Registers

R64CNT

BCNT0AR

RSECAR

BCNT1AR

RMINAR

BCNT2AR

RHRAR

BCNT3AR

RWKAR

BCNT0AER

RDAYAR

BCNT1AER

RMONAR

BCNT2AER

RYRAR

BCNT3AER

RYRAREN

BCNT0

RSECCNT

RCR1

RCR2

RCR2_BCNT

RCR4

RFRH

RFRL

RADJ

BCNT1

RMINCNT

BCNT2

RHRCNT

BCNT3

RWKCNT

RDAYCNT

RMONCNT

RYRCNT


R64CNT

64-Hz Counter
address_offset : 0x0 Bytes (0x0)
size : 8 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0

R64CNT R64CNT read-only 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 F64HZ F32HZ F16HZ F8HZ F4HZ F2HZ F1HZ R64OVF

F64HZ : 64-Hz Flag
bits : 0 - -1 (0 bit)
access : read-only

F32HZ : 32-Hz Flag
bits : 1 - 0 (0 bit)
access : read-only

F16HZ : 16-Hz Flag
bits : 2 - 1 (0 bit)
access : read-only

F8HZ : 8-Hz Flag
bits : 3 - 2 (0 bit)
access : read-only

F4HZ : 4-Hz Flag
bits : 4 - 3 (0 bit)
access : read-only

F2HZ : 2-Hz Flag
bits : 5 - 4 (0 bit)
access : read-only

F1HZ : 1-Hz Flag
bits : 6 - 5 (0 bit)
access : read-only

R64OVF :
bits : 7 - 6 (0 bit)
access : read-only


BCNT0AR

Binary Counter %s Alarm Register
address_offset : 0x10 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

BCNT0AR BCNT0AR read-write 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 BCNTAR

BCNTAR : Alarm register associated with the 32-bit binary counter
bits : 0 - 6 (7 bit)
access : read-write


RSECAR

Second Alarm Register (in Calendar Count Mode)
address_offset : 0x10 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

RSECAR RSECAR read-write 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 SEC1 SEC10 ENB

SEC1 : 1 Second
bits : 0 - 2 (3 bit)
access : read-write

SEC10 : 10 Seconds
bits : 4 - 5 (2 bit)
access : read-write

ENB : ENB
bits : 7 - 6 (0 bit)
access : read-write

Enumeration:

#0 : 0

Do not compare register value with RSECCNT counter value

#1 : 1

Compare register value with RSECCNT counter value

End of enumeration elements list.


BCNT1AR

Binary Counter %s Alarm Register
address_offset : 0x12 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

BCNT1AR BCNT1AR read-write 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 BCNTAR

BCNTAR : Alarm register associated with the 32-bit binary counter
bits : 0 - 6 (7 bit)
access : read-write


RMINAR

Minute Alarm Register (in Calendar Count Mode)
address_offset : 0x12 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

RMINAR RMINAR read-write 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 MIN1 MIN10 ENB

MIN1 : 1 Minute
bits : 0 - 2 (3 bit)
access : read-write

MIN10 : 10 Minutes
bits : 4 - 5 (2 bit)
access : read-write

ENB : ENB
bits : 7 - 6 (0 bit)
access : read-write

Enumeration:

#0 : 0

Do not compare register value with RMINCNT counter value

#1 : 1

Compare register value with RMINCNT counter value

End of enumeration elements list.


BCNT2AR

Binary Counter %s Alarm Register
address_offset : 0x14 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

BCNT2AR BCNT2AR read-write 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 BCNTAR

BCNTAR : Alarm register associated with the 32-bit binary counter
bits : 0 - 6 (7 bit)
access : read-write


RHRAR

Hour Alarm Register (in Calendar Count Mode)
address_offset : 0x14 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

RHRAR RHRAR read-write 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 HR1 HR10 PM ENB

HR1 : 1 Hour
bits : 0 - 2 (3 bit)
access : read-write

HR10 : 10 Hours
bits : 4 - 4 (1 bit)
access : read-write

PM : AM/PM select for alarm setting.
bits : 6 - 5 (0 bit)
access : read-write

Enumeration:

#0 : 0

AM

#1 : 1

PM

End of enumeration elements list.

ENB : ENB
bits : 7 - 6 (0 bit)
access : read-write

Enumeration:

#0 : 0

Do not compare register value with RHRCNT counter value

#1 : 1

Compare register value with RHRCNT counter value

End of enumeration elements list.


BCNT3AR

Binary Counter %s Alarm Register
address_offset : 0x16 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

BCNT3AR BCNT3AR read-write 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 BCNTAR

BCNTAR : Alarm register associated with the 32-bit binary counter
bits : 0 - 6 (7 bit)
access : read-write


RWKAR

Day-of-Week Alarm Register (in Calendar Count Mode)
address_offset : 0x16 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

RWKAR RWKAR read-write 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 DAYW ENB

DAYW : Day-of-Week Setting
bits : 0 - 1 (2 bit)
access : read-write

Enumeration:

#000 : 000

Sunday

#001 : 001

Monday

#010 : 010

Tuesday

#011 : 011

Wednesday

#100 : 100

Thursday

#101 : 101

Friday

#110 : 110

Saturday

#111 : 111

Setting prohibited

End of enumeration elements list.

ENB : ENB
bits : 7 - 6 (0 bit)
access : read-write

Enumeration:

#0 : 0

Do not compare register value with RWKCNT counter value

#1 : 1

Compare register value with RWKCNT counter value

End of enumeration elements list.


BCNT0AER

Binary Counter %s Alarm Enable Register
address_offset : 0x18 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

BCNT0AER BCNT0AER read-write 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0

RDAYAR

Date Alarm Register (in Calendar Count Mode)
address_offset : 0x18 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

RDAYAR RDAYAR read-write 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 DATE1 DATE10 ENB

DATE1 : 1 Day
bits : 0 - 2 (3 bit)
access : read-write

DATE10 : 10 Days
bits : 4 - 4 (1 bit)
access : read-write

ENB : ENB
bits : 7 - 6 (0 bit)
access : read-write

Enumeration:

#0 : 0

Do not compare register value with RDAYCNT counter value

#1 : 1

Compare register value with RDAYCNT counter value

End of enumeration elements list.


BCNT1AER

Binary Counter %s Alarm Enable Register
address_offset : 0x1A Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

BCNT1AER BCNT1AER read-write 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0

RMONAR

Month Alarm Register (in Calendar Count Mode)
address_offset : 0x1A Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

RMONAR RMONAR read-write 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 MON1 MON10 ENB

MON1 : 1 Month
bits : 0 - 2 (3 bit)
access : read-write

MON10 : 10 Months
bits : 4 - 3 (0 bit)
access : read-write

ENB : ENB
bits : 7 - 6 (0 bit)
access : read-write

Enumeration:

#0 : 0

Do not compare register value with RMONCNT counter value

#1 : 1

Compare register value with RMONCNT counter value

End of enumeration elements list.


BCNT2AER

Binary Counter 2 Alarm Enable Register
address_offset : 0x1C Bytes (0x0)
size : 16 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

BCNT2AER BCNT2AER read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

RYRAR

Year Alarm Register (in Calendar Count Mode)
address_offset : 0x1C Bytes (0x0)
size : 16 bit
access : read-write
reset_value : 0x0
alternate_register : BCNT2AER
reset_Mask : 0x0

RYRAR RYRAR read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 YR1 YR10

YR1 : 1 Year
bits : 0 - 2 (3 bit)
access : read-write

YR10 : 10 Years
bits : 4 - 6 (3 bit)
access : read-write


BCNT3AER

Binary Counter 3 Alarm Enable Register
address_offset : 0x1E Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

BCNT3AER BCNT3AER read-write 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0

RYRAREN

Year Alarm Enable Register (in Calendar Count Mode)
address_offset : 0x1E Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
alternate_register : BCNT3AER
reset_Mask : 0x0

RYRAREN RYRAREN read-write 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 ENB

ENB : ENB
bits : 7 - 6 (0 bit)
access : read-write

Enumeration:

#0 : 0

Do not compare register value with the RYRCNT counter value

#1 : 1

Compare register value with the RYRCNT counter value

End of enumeration elements list.


BCNT0

Binary Counter %s
address_offset : 0x2 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

BCNT0 BCNT0 read-write 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 BCNT

BCNT : Binary Counter
bits : 0 - 6 (7 bit)
access : read-write


RSECCNT

Second Counter (in Calendar Count Mode)
address_offset : 0x2 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

RSECCNT RSECCNT read-write 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 SEC1 SEC10

SEC1 : 1-Second Count
bits : 0 - 2 (3 bit)
access : read-write

SEC10 : 10-Second Count
bits : 4 - 5 (2 bit)
access : read-write


RCR1

RTC Control Register 1
address_offset : 0x22 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

RCR1 RCR1 read-write 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 AIE CIE PIE RTCOS PES

AIE : Alarm Interrupt Enable
bits : 0 - -1 (0 bit)
access : read-write

Enumeration:

#0 : 0

Disable alarm interrupt requests

#1 : 1

Enable alarm interrupt requests

End of enumeration elements list.

CIE : Carry Interrupt Enable
bits : 1 - 0 (0 bit)
access : read-write

Enumeration:

#0 : 0

Disable carry interrupt requests

#1 : 1

Enable carry interrupt requests

End of enumeration elements list.

PIE : Periodic Interrupt Enable
bits : 2 - 1 (0 bit)
access : read-write

Enumeration:

#0 : 0

Disable periodic interrupt requests

#1 : 1

Enable periodic interrupt requests

End of enumeration elements list.

RTCOS : RTCOUT Output Select
bits : 3 - 2 (0 bit)
access : read-write

Enumeration:

#0 : 0

Outputs 1 Hz on RTCOUT

#1 : 1

Outputs 64 Hz RTCOUT

End of enumeration elements list.

PES : Periodic Interrupt Select
bits : 4 - 6 (3 bit)
access : read-write

Enumeration:

0x6 : 0x6

Generate periodic interrupt every 1/256 second

0x7 : 0x7

Generate periodic interrupt every 1/128 second

0x8 : 0x8

Generate periodic interrupt every 1/64 second

0x9 : 0x9

Generate periodic interrupt every 1/32 second

0xa : 0xA

Generate periodic interrupt every 1/16 second

0xb : 0xB

Generate periodic interrupt every 1/8 second

0xc : 0xC

Generate periodic interrupt every 1/4 second

0xd : 0xD

Generate periodic interrupt every 1/2 second

0xe : 0xE

Generate periodic interrupt every 1 second

0xf : 0xF

Generate periodic interrupt every 2 seconds

: Others

Do not generate periodic interrupts

End of enumeration elements list.


RCR2

RTC Control Register 2 (in Calendar Count Mode)
address_offset : 0x24 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

RCR2 RCR2 read-write 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 START RESET ADJ30 RTCOE AADJE AADJP HR24 CNTMD

START : Start
bits : 0 - -1 (0 bit)
access : read-write

Enumeration:

#0 : 0

Stop prescaler and time counter

#1 : 1

Operate prescaler and time counter normally

End of enumeration elements list.

RESET : RTC Software Reset
bits : 1 - 0 (0 bit)
access : read-write

Enumeration:

#0 : 0

In writing: Invalid (writing 0 has no effect). In reading: Normal time operation in progress, or an RTC software reset has completed.

#1 : 1

In writing: Initialize the prescaler and target registers for RTC software reset. In reading: RTC software reset in progress.

End of enumeration elements list.

ADJ30 : 30-Second Adjustment
bits : 2 - 1 (0 bit)
access : read-write

Enumeration:

#0 : 0

In writing: Invalid (writing 0 has no effect). In reading: Normal time operation in progress, or 30-second adjustment has completed.

#1 : 1

In writing: Execute 30-second adjustment. In reading: 30-second adjustment in progress.

End of enumeration elements list.

RTCOE : RTCOUT Output Enable
bits : 3 - 2 (0 bit)
access : read-write

Enumeration:

#0 : 0

Disable RTCOUT output

#1 : 1

Enable RTCOUT output

End of enumeration elements list.

AADJE : Automatic Adjustment Enable
bits : 4 - 3 (0 bit)
access : read-write

Enumeration:

#0 : 0

Disable automatic adjustment

#1 : 1

Enable automatic adjustment

End of enumeration elements list.

AADJP : Automatic Adjustment Period Select
bits : 5 - 4 (0 bit)
access : read-write

Enumeration:

#0 : 0

In normal operation mode, adjust RADJ.ADJ[5:0] setting from the count value of the prescaler every minute. In low-consumption clock mode, adjust RADJ.ADJ[5:0] setting from the count value of the 64-Hz counter every day.

#1 : 1

In normal operation mode, adjust RADJ.ADJ[5:0] setting from the count value of the prescaler every 10 seconds. In low-consumption clock mode, adjust RADJ.ADJ[5:0] setting from the count value of the 64-Hz counter every hour.

End of enumeration elements list.

HR24 : Hours Mode
bits : 6 - 5 (0 bit)
access : read-write

Enumeration:

#0 : 0

Operate RTC in 12-hour mode

#1 : 1

Operate RTC in 24-hour mode

End of enumeration elements list.

CNTMD : Count Mode Select
bits : 7 - 6 (0 bit)
access : read-write

Enumeration:

#0 : 0

Calendar count mode

#1 : 1

Binary count mode

End of enumeration elements list.


RCR2_BCNT

RTC Control Register 2 (in Binary Count Mode)
address_offset : 0x24 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
alternate_register : RCR2
reset_Mask : 0x0

RCR2_BCNT RCR2_BCNT read-write 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 START RESET RTCOE AADJE AADJP CNTMD

START : Start
bits : 0 - -1 (0 bit)
access : read-write

Enumeration:

#0 : 0

Stop the 32-bit binary counter, 64-Hz counter, and prescaler

#1 : 1

Operate the 32-bit binary counter, 64-Hz counter, and prescaler normally

End of enumeration elements list.

RESET : RTC Software Reset
bits : 1 - 0 (0 bit)
access : read-write

Enumeration:

#0 : 0

In writing: Invalid (writing 0 has no effect). In reading: Normal time operation in progress, or an RTC software reset has completed.

#1 : 1

In writing: Initialize the prescaler and target registers for RTC software reset. In reading: RTC software reset in progress.

End of enumeration elements list.

RTCOE : RTCOUT Output Enable
bits : 3 - 2 (0 bit)
access : read-write

Enumeration:

#0 : 0

Disable RTCOUT output

#1 : 1

Enable RTCOUT output

End of enumeration elements list.

AADJE : Automatic Adjustment Enable
bits : 4 - 3 (0 bit)
access : read-write

Enumeration:

#0 : 0

Disable automatic adjustment

#1 : 1

Enable automatic adjustment

End of enumeration elements list.

AADJP : Automatic Adjustment Period Select
bits : 5 - 4 (0 bit)
access : read-write

Enumeration:

#0 : 0

In normal operation mode, add or subtract the RADJ.ADJ[5:0] bits from the prescaler count value every 32 seconds. In low-consumption clock mode, add or subtract the RADJ.ADJ[5:0] bits from the 64-Hz counter count value every 8192 seconds.

#1 : 1

In normal operation mode, add or subtract the RADJ.ADJ[5:0] bits from the prescaler count value every 8 seconds. In low-consumption clock mode, add or subtract the RADJ.ADJ[5:0] bits from the 64-Hz counter count value every 2048 seconds.

End of enumeration elements list.

CNTMD : Count Mode Select
bits : 7 - 6 (0 bit)
access : read-write

Enumeration:

#0 : 0

Calendar count mode

#1 : 1

Binary count mode

End of enumeration elements list.


RCR4

RTC Control Register 4
address_offset : 0x28 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

RCR4 RCR4 read-write 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 RCKSEL ROPSEL

RCKSEL : Count Source Select in normal operation mode
bits : 0 - -1 (0 bit)
access : read-write

Enumeration:

#0 : 0

Sub-clock oscillator is selected

#1 : 1

LOCO is selected

End of enumeration elements list.

ROPSEL : RTC Operation Mode Select
bits : 7 - 6 (0 bit)
access : read-write

Enumeration:

#0 : 0

Normal operation mode is selected.

#1 : 1

Low-consumption clock mode is selected.

End of enumeration elements list.


RFRH

Frequency Register H
address_offset : 0x2A Bytes (0x0)
size : 16 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

RFRH RFRH read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 RFC16

RFC16 : Write 0 before writing to the RFRL register after a cold start.
bits : 0 - -1 (0 bit)
access : read-write


RFRL

Frequency Register L
address_offset : 0x2C Bytes (0x0)
size : 16 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

RFRL RFRL read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 RFC

RFC : Frequency Comparison Value
bits : 0 - 14 (15 bit)
access : read-write


RADJ

Time Error Adjustment Register
address_offset : 0x2E Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

RADJ RADJ read-write 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 ADJ PMADJ

ADJ : Adjustment Value
bits : 0 - 4 (5 bit)
access : read-write

PMADJ : Plus-Minus
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

#00 : 00

Do not perform adjustment.

#01 : 01

In normal operation mode, adjustment is performed by the addition to the prescaler. In low-consumption clock mode, adjustment is performed by the addition to the 64-Hz counter.

#10 : 10

In normal operation mode, adjustment is performed by the subtraction from the prescaler. In low-consumption clock mode, adjustment is performed by the subtraction from the 64-Hz counter.

#11 : 11

Setting prohibited.

End of enumeration elements list.


BCNT1

Binary Counter %s
address_offset : 0x4 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

BCNT1 BCNT1 read-write 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 BCNT

BCNT : Binary Counter
bits : 0 - 6 (7 bit)
access : read-write


RMINCNT

Minute Counter (in Calendar Count Mode)
address_offset : 0x4 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

RMINCNT RMINCNT read-write 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 MIN1 MIN10

MIN1 : 1-Minute Count
bits : 0 - 2 (3 bit)
access : read-write

MIN10 : 10-Minute Count
bits : 4 - 5 (2 bit)
access : read-write


BCNT2

Binary Counter %s
address_offset : 0x6 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

BCNT2 BCNT2 read-write 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 BCNT

BCNT : Binary Counter
bits : 0 - 6 (7 bit)
access : read-write


RHRCNT

Hour Counter (in Calendar Count Mode)
address_offset : 0x6 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

RHRCNT RHRCNT read-write 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 HR1 HR10 PM

HR1 : 1-Hour Count
bits : 0 - 2 (3 bit)
access : read-write

HR10 : 10-Hour Count
bits : 4 - 4 (1 bit)
access : read-write

PM : AM/PM select for time counter setting.
bits : 6 - 5 (0 bit)
access : read-write

Enumeration:

#0 : 0

AM

#1 : 1

PM

End of enumeration elements list.


BCNT3

Binary Counter %s
address_offset : 0x8 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

BCNT3 BCNT3 read-write 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 BCNT

BCNT : Binary Counter
bits : 0 - 6 (7 bit)
access : read-write


RWKCNT

Day-of-Week Counter (in Calendar Count Mode)
address_offset : 0x8 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

RWKCNT RWKCNT read-write 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 DAYW

DAYW : Day-of-Week Counting
bits : 0 - 1 (2 bit)
access : read-write

Enumeration:

#000 : 000

Sunday

#001 : 001

Monday

#010 : 010

Tuesday

#011 : 011

Wednesday

#100 : 100

Thursday

#101 : 101

Friday

#110 : 110

Saturday

#111 : 111

Setting prohibited

End of enumeration elements list.


RDAYCNT

Day Counter
address_offset : 0xA Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

RDAYCNT RDAYCNT read-write 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 DATE1 DATE10

DATE1 : 1-Day Count
bits : 0 - 2 (3 bit)
access : read-write

DATE10 : 10-Day Count
bits : 4 - 4 (1 bit)
access : read-write


RMONCNT

Month Counter
address_offset : 0xC Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

RMONCNT RMONCNT read-write 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 MON1 MON10

MON1 : 1-Month Count
bits : 0 - 2 (3 bit)
access : read-write

MON10 : 10-Month Count
bits : 4 - 3 (0 bit)
access : read-write


RYRCNT

Year Counter
address_offset : 0xE Bytes (0x0)
size : 16 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

RYRCNT RYRCNT read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 YR1 YR10

YR1 : 1-Year Count
bits : 0 - 2 (3 bit)
access : read-write

YR10 : 10-Year Count
bits : 4 - 6 (3 bit)
access : read-write



Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !

This website is sponsored by EmbeetleEmbeetle, an IDE designed from scratch for embedded software developers.