\n

IIC0WU

Peripheral Memory Blocks

address_offset : 0x2 Bytes (0x0)
size : 0x2 byte (0x0)
mem_usage : registers
protection : not protected

Registers

ICWUR

ICWUR2


ICWUR

I2C Bus Wakeup Unit Register
address_offset : 0x2 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

ICWUR ICWUR read-write 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 WUAFA WUACK WUF WUIE WUE

WUAFA : Wakeup Analog Filter Additional Selection
bits : 0 - -1 (0 bit)
access : read-write

Enumeration:

#0 : 0

Do not add the wakeup analog filter

#1 : 1

Add the wakeup analog filter

End of enumeration elements list.

WUACK : ACK Bit for Wakeup Mode
bits : 4 - 3 (0 bit)
access : read-write

WUF : Wakeup Event Occurrence Flag
bits : 5 - 4 (0 bit)
access : read-write

Enumeration:

#0 : 0

Slave address not matching during wakeup

#1 : 1

Slave address matching during wakeup

End of enumeration elements list.

WUIE : Wakeup Interrupt Request Enable
bits : 6 - 5 (0 bit)
access : read-write

Enumeration:

#0 : 0

Disable wakeup interrupt request (IIC0_WUI)

#1 : 1

Enable wakeup interrupt request (IIC0_WUI)

End of enumeration elements list.

WUE : Wakeup Function Enable
bits : 7 - 6 (0 bit)
access : read-write

Enumeration:

#0 : 0

Disable wakeup function

#1 : 1

Enable wakeup function

End of enumeration elements list.


ICWUR2

I2C Bus Wakeup Unit Register 2
address_offset : 0x3 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

ICWUR2 ICWUR2 read-write 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 WUSEN WUASYF WUSYF

WUSEN : Wakeup Function Synchronous Enable
bits : 0 - -1 (0 bit)
access : read-write

Enumeration:

#0 : 0

IIC asynchronous circuit enable

#1 : 1

IIC synchronous circuit enable

End of enumeration elements list.

WUASYF : Wakeup Function Asynchronous Operation Status Flag
bits : 1 - 0 (0 bit)
access : read-only

Enumeration:

#0 : 0

IIC synchronous circuit enable condition

#1 : 1

IIC asynchronous circuit enable condition

End of enumeration elements list.

WUSYF : Wakeup Function Synchronous Operation Status Flag
bits : 2 - 1 (0 bit)
access : read-only

Enumeration:

#0 : 0

IIC asynchronous circuit enable condition

#1 : 1

IIC synchronous circuit enable condition

End of enumeration elements list.



Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !

This website is sponsored by EmbeetleEmbeetle, an IDE designed from scratch for embedded software developers.