\n
address_offset : 0x0 Bytes (0x0)
size : 0xC byte (0x0)
mem_usage : registers
protection :
Module Stop Control Register B
address_offset : 0x0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MSTPB1 : Controller Area Network 1 Module Stop
bits : 1 - 0 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPB2 : Controller Area Network 0 Module Stop
bits : 2 - 1 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPB5 : IrDA Module Stop
bits : 5 - 4 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPB6 : Queued Serial Peripheral Interface Module Stop
bits : 6 - 5 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPB8 : I2C Bus Interface 1 Module Stop
bits : 8 - 7 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPB9 : I2C Bus Interface 0 Module Stop
bits : 9 - 8 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPB11 : Universal Serial Bus 2.0 FS Interface Module Stop
bits : 11 - 10 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPB18 : Serial Peripheral Interface Module Stop
bits : 18 - 17 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPB19 : Serial Peripheral Interface 0 Module Stop
bits : 19 - 18 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPB22 : Serial Communication Interface 9 Module Stop
bits : 22 - 21 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPB23 : Serial Communication Interface 8 Module Stop
bits : 23 - 22 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPB27 : Serial Communication Interface 4 Module Stop
bits : 27 - 26 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPB28 : Serial Communication Interface 3 Module Stop
bits : 28 - 27 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPB29 : Serial Communication Interface 2 Module Stop
bits : 29 - 28 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPB30 : Serial Communication Interface 1 Module Stop
bits : 30 - 29 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPB31 : Serial Communication Interface 0 Module Stop
bits : 31 - 30 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
Module Stop Control Register C
address_offset : 0x4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MSTPC0 : Clock Frequency Accuracy Measurement Circuit Module Stop
bits : 0 - -1 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPC1 : Cyclic Redundancy Check Calculator Module Stop
bits : 1 - 0 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPC3 : Capacitive Touch Sensing Unit Module Stop
bits : 3 - 2 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPC8 : Serial Sound Interface Enhanced (channel 0) Module Stop
bits : 8 - 7 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPC9 : Sampling Rate Converter Module Stop
bits : 9 - 8 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPC11 : Secure Digital Host IF/MultiMediaCard 1 Module Stop
bits : 11 - 10 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPC12 : Secure Digital Host IF/MultiMediaCard 0 Module Stop
bits : 12 - 11 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPC13 : Data Operation Circuit Module Stop
bits : 13 - 12 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPC14 : Event Link Controller Module Stop
bits : 14 - 13 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPC31 : SCE7 Module Stop
bits : 31 - 30 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
Module Stop Control Register D
address_offset : 0x8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MSTPD2 : AGT1 Module Stop Note: AGT1 is in the module stop state when the count source is either of PCLKB, PCLKB/2 or PCLKB/8. In case the count source is sub-clock or LOCO, this bit should be set to 1 except when accessing the registers of AGT1.
bits : 2 - 1 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPD3 : AGT0 Module Stop Note: AGT0 is in the module stop state when the count source is either of PCLKB, PCLKB/2 or PCLKB/8. In case the count source is sub-clock or LOCO, this bit should be set to 1 except when accessing the registers of AGT0.
bits : 3 - 2 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPD5 : General PWM Timer 32EH0 to 32EH3 and 32E4 to 32E7 and PWM Delay Generation Circuit Module Stop
bits : 5 - 4 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPD6 : General PWM Timer 32_8 to 32_12 Module Stop
bits : 6 - 5 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPD14 : Port Output Enable for GPT Module Stop
bits : 14 - 13 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPD15 : 12-Bit A/D Converter 1 Module Stop
bits : 15 - 14 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPD16 : 12-Bit A/D Converter 0 Module Stop
bits : 16 - 15 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPD20 : 12-Bit D/A Converter Module Stop
bits : 20 - 19 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPD22 : Temperature Sensor Module Stop
bits : 22 - 21 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPD23 : High-Speed Analog Comparator 5 Module Stop
bits : 23 - 22 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPD24 : High-Speed Analog Comparator 4 Module Stop
bits : 24 - 23 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPD25 : High-Speed Analog Comparator 3 Module Stop
bits : 25 - 24 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPD26 : High-Speed Analog Comparator 2 Module Stop
bits : 26 - 25 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPD27 : High-Speed Analog Comparator 1 Module Stop
bits : 27 - 26 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPD28 : High-Speed Analog Comparator 0 Module Stop
bits : 28 - 27 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !
This website is sponsored by Embeetle, an IDE designed from scratch for embedded software developers.