Embeetle, an IDE designed from scratch for embedded software developers.address_offset : 0x0 Bytes (0x0)
size : 0x74 byte (0x0)
mem_usage : registers
protection :
address_offset : 0x7C Bytes (0x0)
size : 0x4 byte (0x0)
mem_usage : registers
protection :
address_offset : 0x74 Bytes (0x0)
size : 0x4 byte (0x0)
mem_usage : registers
protection :
address_offset : 0x80 Bytes (0x0)
size : 0x4 byte (0x0)
mem_usage : registers
protection :
address_offset : 0x78 Bytes (0x0)
size : 0x4 byte (0x0)
mem_usage : registers
protection :
address_offset : 0x84 Bytes (0x0)
size : 0x20 byte (0x0)
mem_usage : registers
protection :
General PWM Timer Write-Protection Register
address_offset : 0x0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
WP : Register Write Disable
bits : 0 - -1 (0 bit)
access : read-write
Enumeration:
#0 : 0
Enable writes to the register
#1 : 1
Disable writes to the register
End of enumeration elements list.
Reserved : These bits are read as 0000000. The write value should be 0000000.
bits : 1 - 6 (6 bit)
access : read-write
Reserved : These bits are read as 0000000. The write value should be 0000000.
bits : 1 - 6 (6 bit)
access : read-write
PRKEY : GTWP Key Code
bits : 8 - 14 (7 bit)
access : write-only
Enumeration:
0xA5 : 0xA5
Written to these bits, the WP bits write is permitted.
: others
The WP bits write is not permitted.
End of enumeration elements list.
General PWM Timer Start Source Select Register
address_offset : 0x10 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
SSGTRGAR : GTETRGA Pin Rising Input Source Counter Start Enable
bits : 0 - -1 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter start on the rising edge of GTETRGA input
#1 : 1
Enable counter start on the rising edge of GTETRGA input.
End of enumeration elements list.
SSGTRGAF : GTETRGA Pin Falling Input Source Counter Start Enable
bits : 1 - 0 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter start on the falling edge of GTETRGA input
#1 : 1
Enable counter start on the falling edge of GTETRGA input
End of enumeration elements list.
SSGTRGBR : GTETRGB Pin Rising Input Source Counter Start Enable
bits : 2 - 1 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter start on the rising edge of GTETRGB input
#1 : 1
Enable counter start on the rising edge of GTETRGB input.
End of enumeration elements list.
SSGTRGBF : GTETRGB Pin Falling Input Source Counter Start Enable
bits : 3 - 2 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter start on the falling edge of GTETRGB input
#1 : 1
Enable counter start on the falling edge of GTETRGB input
End of enumeration elements list.
SSGTRGCR : GTETRGC Pin Rising Input Source Counter Start Enable
bits : 4 - 3 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter start on the rising edge of GTETRGC input
#1 : 1
Enable counter start on the rising edge of GTETRGC input
End of enumeration elements list.
SSGTRGCF : GTETRGC Pin Falling Input Source Counter Start Enable
bits : 5 - 4 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter start on the falling edge of GTETRGC input
#1 : 1
Enable counter start on the falling edge of GTETRGC input
End of enumeration elements list.
SSGTRGDR : GTETRGD Pin Rising Input Source Counter Start Enable
bits : 6 - 5 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter start on the rising edge of GTETRGD input
#1 : 1
Enable counter start on the rising edge of GTETRGD input
End of enumeration elements list.
SSGTRGDF : GTETRGD Pin Falling Input Source Counter Start Enable
bits : 7 - 6 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter start on the falling edge of GTETRGD input
#1 : 1
Enable counter start on the falling edge of GTETRGD input.
End of enumeration elements list.
SSCARBL : GTIOCA Pin Rising Input during GTIOCB Value Low Source Counter Start Enable
bits : 8 - 7 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter start on the rising edge of GTIOCA input when GTIOCB input is 0
#1 : 1
Enable counter start on the rising edge of GTIOCA input when GTIOCB input is 0.
End of enumeration elements list.
SSCARBH : GTIOCA Pin Rising Input during GTIOCB Value High Source Counter Start Enable
bits : 9 - 8 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter start on the rising edge of GTIOCA input when GTIOCB input is 1
#1 : 1
Enable counter start on the rising edge of GTIOCA input when GTIOCB input is 1
End of enumeration elements list.
SSCAFBL : GTIOCA Pin Falling Input during GTIOCB Value Low Source Counter Start Enable
bits : 10 - 9 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter start on the falling edge of GTIOCA input when GTIOCB input is 0
#1 : 1
Enable counter start on the falling edge of GTIOCA input when GTIOCB input is 0.
End of enumeration elements list.
SSCAFBH : GTIOCA Pin Falling Input during GTIOCB Value High Source Counter Start Enable
bits : 11 - 10 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter start on the falling edge of GTIOCA input when GTIOCB input is 1
#1 : 1
Enable counter start on the falling edge of GTIOCA input when GTIOCB input is 1.
End of enumeration elements list.
SSCBRAL : GTIOCB Pin Rising Input during GTIOCA Value Low Source Counter Start Enable
bits : 12 - 11 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter start on the rising edge of GTIOCB input when GTIOCA input is 0
#1 : 1
Enable counter start on the rising edge of GTIOCB input when GTIOCA input is 0.
End of enumeration elements list.
SSCBRAH : GTIOCB Pin Rising Input during GTIOCA Value High Source Counter Start Enable
bits : 13 - 12 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter start on the rising edge of GTIOCB input when GTIOCA input is 1
#1 : 1
Enable counter start on the rising edge of GTIOCB input when GTIOCA input is 1.
End of enumeration elements list.
SSCBFAL : GTIOCB Pin Falling Input during GTIOCA Value Low Source Counter Start Enable
bits : 14 - 13 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter start on the falling edge of GTIOCB input when GTIOCA input is 0
#1 : 1
Enable counter start on the falling edge of GTIOCB input when GTIOCA input is 0.
End of enumeration elements list.
SSCBFAH : GTIOCB Pin Falling Input during GTIOCA Value High Source Counter Start Enable
bits : 15 - 14 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter start on the falling edge of GTIOCB input when GTIOCA input is 1
#1 : 1
Enable counter start on the falling edge of GTIOCB input when GTIOCA input is 1.
End of enumeration elements list.
SSELCA : ELC_GPTA Event Source Counter Start Enable
bits : 16 - 15 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter start on ELC_GPTA input
#1 : 1
Enable counter start on ELC_GPTA input.
End of enumeration elements list.
SSELCB : ELC_GPTB Event Source Counter Start Enable
bits : 17 - 16 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter start on ELC_GPTB input
#1 : 1
Enable counter start on ELC_GPTB input.
End of enumeration elements list.
SSELCC : ELC_GPTC Event Source Counter Start Enable
bits : 18 - 17 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter start on ELC_GPTC input
#1 : 1
Enable counter start on ELC_GPTC input.
End of enumeration elements list.
SSELCD : ELC_GPTD Event Source Counter Start Enable
bits : 19 - 18 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter start on ELC_GPTD input
#1 : 1
Enable counter start on ELC_GPTD input.
End of enumeration elements list.
SSELCE : ELC_GPTE Event Source Counter Start Enable
bits : 20 - 19 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter start on ELC_GPTE input
#1 : 1
Enable counter start on ELC_GPTE input
End of enumeration elements list.
SSELCF : ELC_GPTF Event Source Counter Start Enable
bits : 21 - 20 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter start on ELC_GPTF input
#1 : 1
Enable counter start on ELC_GPTF input
End of enumeration elements list.
SSELCG : ELC_GPTG Event Source Counter Start Enable
bits : 22 - 21 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter start on ELC_GPTG input
#1 : 1
Enable counter start on ELC_GPTG input.
End of enumeration elements list.
SSELCH : ELC_GPTH Event Source Counter Start Enable
bits : 23 - 22 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter start on ELC_GPTH input
#1 : 1
Enable counter start on ELC_GPTH input.
End of enumeration elements list.
Reserved : These bits are read as 0000000. The write value should be 0000000.
bits : 24 - 29 (6 bit)
access : read-write
CSTRT : Software Source Counter Start Enable
bits : 31 - 30 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter start by the GTSTR register
#1 : 1
Enable counter start by the GTSTR register
End of enumeration elements list.
General PWM Timer Stop Source Select Register
address_offset : 0x14 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PSGTRGAR : GTETRGA Pin Rising Input Source Counter Stop Enable
bits : 0 - -1 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter stop on the rising edge of GTETRGA input
#1 : 1
Enable counter stop on the rising edge of GTETRGA input
End of enumeration elements list.
PSGTRGAF : GTETRGA Pin Falling Input Source Counter Stop Enable
bits : 1 - 0 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter stop on the falling edge of GTETRGA input
#1 : 1
Enable counter stop on the falling edge of GTETRGA input
End of enumeration elements list.
PSGTRGBR : GTETRGB Pin Rising Input Source Counter Stop Enable
bits : 2 - 1 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter stop on the rising edge of GTETRGB input
#1 : 1
Enable counter stop on the rising edge of GTETRGB input
End of enumeration elements list.
PSGTRGBF : GTETRGB Pin Falling Input Source Counter Stop Enable
bits : 3 - 2 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter stop on the falling edge of GTETRGB input
#1 : 1
Enable counter stop on the falling edge of GTETRGB input
End of enumeration elements list.
PSGTRGCR : GTETRGC Pin Rising Input Source Counter Stop Enable
bits : 4 - 3 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter stop on the rising edge of GTETRGC input
#1 : 1
Enable counter stop on the rising edge of GTETRGC input
End of enumeration elements list.
PSGTRGCF : GTETRGC Pin Falling Input Source Counter Stop Enable
bits : 5 - 4 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter stop on the falling edge of GTETRGC input
#1 : 1
Enable counter stop on the falling edge of GTETRGC input
End of enumeration elements list.
PSGTRGDR : GTETRGD Pin Rising Input Source Counter Stop Enable
bits : 6 - 5 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter stop on the rising edge of GTETRGD input
#1 : 1
Enable counter stop on the rising edge of GTETRGD input
End of enumeration elements list.
PSGTRGDF : GTETRGD Pin Falling Input Source Counter Stop Enable
bits : 7 - 6 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter stop on the falling edge of GTETRGD input
#1 : 1
Enable counter stop on the falling edge of GTETRGD input
End of enumeration elements list.
PSCARBL : GTIOCA Pin Rising Input during GTIOCB Value Low Source Counter Stop Enable
bits : 8 - 7 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter stop on the rising edge of GTIOCA input when GTIOCB input is 0
#1 : 1
Enable counter stop on the rising edge of GTIOCA input when GTIOCB input is 0
End of enumeration elements list.
PSCARBH : GTIOCA Pin Rising Input during GTIOCB Value High Source Counter Stop Enable
bits : 9 - 8 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter stop on the rising edge of GTIOCA input when GTIOCB input is 1
#1 : 1
Enable counter stop on the rising edge of GTIOCA input when GTIOCB input is 1
End of enumeration elements list.
PSCAFBL : GTIOCA Pin Falling Input during GTIOCB Value Low Source Counter Stop Enable
bits : 10 - 9 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter stop on the falling edge of GTIOCA input when GTIOCB input is 0
#1 : 1
Enable counter stop on the falling edge of GTIOCA input when GTIOCB input is 0
End of enumeration elements list.
PSCAFBH : GTIOCA Pin Falling Input during GTIOCB Value High Source Counter Stop Enable
bits : 11 - 10 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter stop on the falling edge of GTIOCA input when GTIOCB input is 1
#1 : 1
Enable counter stop on the falling edge of GTIOCA input when GTIOCB input is 1
End of enumeration elements list.
PSCBRAL : GTIOCB Pin Rising Input during GTIOCA Value Low Source Counter Stop Enable
bits : 12 - 11 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter stop on the rising edge of GTIOCB input when GTIOCA input is 0
#1 : 1
Enable counter stop on the rising edge of GTIOCB input when GTIOCA input is 0
End of enumeration elements list.
PSCBRAH : GTIOCB Pin Rising Input during GTIOCA Value High Source Counter Stop Enable
bits : 13 - 12 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter stop on the rising edge of GTIOCB input when GTIOCA input is 1
#1 : 1
Enable counter stop on the rising edge of GTIOCB input when GTIOCA input is 1
End of enumeration elements list.
PSCBFAL : GTIOCB Pin Falling Input during GTIOCA Value Low Source Counter Stop Enable
bits : 14 - 13 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter stop on the falling edge of GTIOCB input when GTIOCA input is 0
#1 : 1
Enable counter stop on the falling edge of GTIOCB input when GTIOCA input is 0
End of enumeration elements list.
PSCBFAH : GTIOCB Pin Falling Input during GTIOCA Value High Source Counter Stop Enable
bits : 15 - 14 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter stop on the falling edge of GTIOCB input when GTIOCA input is 1
#1 : 1
Enable counter stop on the falling edge of GTIOCB input when GTIOCA input is 1
End of enumeration elements list.
PSELCA : ELC_GPTA Event Source Counter Stop Enable
bits : 16 - 15 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter stop on ELC_GPTA input
#1 : 1
Enable counter stop on ELC_GPTA input
End of enumeration elements list.
PSELCB : ELC_GPTB Event Source Counter Stop Enable
bits : 17 - 16 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter stop on ELC_GPTB input
#1 : 1
Enable counter stop on ELC_GPTB input
End of enumeration elements list.
PSELCC : ELC_GPTC Event Source Counter Stop Enable
bits : 18 - 17 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter stop on ELC_GPTC input
#1 : 1
Enable counter stop on ELC_GPTC input
End of enumeration elements list.
PSELCD : ELC_GPTD Event Source Counter Stop Enable
bits : 19 - 18 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter stop on ELC_GPTD input
#1 : 1
Enable counter stop on ELC_GPTD input
End of enumeration elements list.
PSELCE : ELC_GPTE Event Source Counter Stop Enable
bits : 20 - 19 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter stop on ELC_GPTE input
#1 : 1
Enable counter stop on ELC_GPTE input
End of enumeration elements list.
PSELCF : ELC_GPTF Event Source Counter Stop Enable
bits : 21 - 20 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter stop on ELC_GPTF input
#1 : 1
Enable counter stop on ELC_GPTF input
End of enumeration elements list.
PSELCG : ELC_GPTG Event Source Counter Stop Enable
bits : 22 - 21 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter stop on ELC_GPTG input
#1 : 1
Enable counter stop on ELC_GPTG input
End of enumeration elements list.
PSELCH : ELC_GPTH Event Source Counter Stop Enable
bits : 23 - 22 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter stop on ELC_GPTH input
#1 : 1
Enable counter stop on ELCH event inpu
End of enumeration elements list.
Reserved : These bits are read as 0000000. The write value should be 0000000.
bits : 24 - 29 (6 bit)
access : read-write
CSTOP : Software Source Counter Stop Enable
bits : 31 - 30 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter stop by the GTSTP register
#1 : 1
Enable counter stop by the GTSTP register
End of enumeration elements list.
General PWM Timer Clear Source Select Register
address_offset : 0x18 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
CSGTRGAR : GTETRGA Pin Rising Input Source Counter Clear Enable
bits : 0 - -1 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter clear on the rising edge of GTETRGA input
#1 : 1
Enable counter clear on the rising edge of GTETRGA input
End of enumeration elements list.
CSGTRGAF : GTETRGA Pin Falling Input Source Counter Clear Enable
bits : 1 - 0 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter clear on the falling edge of GTETRGA input
#1 : 1
Enable counter clear on the falling edge of GTETRGA input
End of enumeration elements list.
CSGTRGBR : GTETRGB Pin Rising Input Source Counter Clear Enable
bits : 2 - 1 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter clear on the rising edge of GTETRGB input
#1 : 1
Enable counter clear on the rising edge of GTETRGB input
End of enumeration elements list.
CSGTRGBF : GTETRGB Pin Falling Input Source Counter Clear Enable
bits : 3 - 2 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter clear on the falling edge of GTETRGB input
#1 : 1
Enable counter clear on the falling edge of GTETRGB input
End of enumeration elements list.
CSGTRGCR : GTETRGC Pin Rising Input Source Counter Clear Enable
bits : 4 - 3 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter clear on the rising edge of GTETRGC input
#1 : 1
Enable counter clear on the rising edge of GTETRGC input
End of enumeration elements list.
CSGTRGCF : GTETRGC Pin Falling Input Source Counter Clear Enable
bits : 5 - 4 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter clear on the falling edge of GTETRGC input
#1 : 1
Enable counter clear on the falling edge of GTETRGC input
End of enumeration elements list.
CSGTRGDR : GTETRGD Pin Rising Input Source Counter Clear Enable
bits : 6 - 5 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter clear on the rising edge of GTETRGD input
#1 : 1
Enable counter clear on the rising edge of GTETRGD input
End of enumeration elements list.
CSGTRGDF : GTETRGD Pin Falling Input Source Counter Clear Enable
bits : 7 - 6 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter clear on the falling edge of GTETRGD input
#1 : 1
Enable counter clear on the falling edge of GTETRGD input
End of enumeration elements list.
CSCARBL : GTIOCA Pin Rising Input during GTIOCB Value Low Source Counter Clear Enable
bits : 8 - 7 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter clear on the rising edge of GTIOCA input when GTIOCB input is 0
#1 : 1
Enable counter clear on the rising edge of GTIOCA input when GTIOCB input is 0
End of enumeration elements list.
CSCARBH : GTIOCA Pin Rising Input during GTIOCB Value High Source Counter Clear Enable
bits : 9 - 8 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter clear on the rising edge of GTIOCA input when GTIOCB input is 1
#1 : 1
Enable counter clear on the rising edge of GTIOCA input when GTIOCB input is 1
End of enumeration elements list.
CSCAFBL : GTIOCA Pin Falling Input during GTIOCB Value Low Source Counter Clear Enable
bits : 10 - 9 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter clear on the falling edge of GTIOCA input when GTIOCB input is 0
#1 : 1
Enable counter clear on the falling edge of GTIOCA input when GTIOCB input is 0
End of enumeration elements list.
CSCAFBH : GTIOCA Pin Falling Input during GTIOCB Value High Source Counter Clear Enable
bits : 11 - 10 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter clear on the falling edge of GTIOCA input when GTIOCB input is 1
#1 : 1
Enable counter clear on the falling edge of GTIOCA input when GTIOCB input is 1
End of enumeration elements list.
CSCBRAL : GTIOCB Pin Rising Input during GTIOCA Value Low Source Counter Clear Enable
bits : 12 - 11 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter clear on the rising edge of GTIOCB input when GTIOCA input is 0
#1 : 1
Enable counter clear on the rising edge of GTIOCB input when GTIOCA input is 0
End of enumeration elements list.
CSCBRAH : GTIOCB Pin Rising Input during GTIOCA Value High Source Counter Clear Enable
bits : 13 - 12 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter clear on the rising edge of GTIOCB input when GTIOCA input is 1
#1 : 1
Enable counter clear on the rising edge of GTIOCB input when GTIOCA input is 1
End of enumeration elements list.
CSCBFAL : GTIOCB Pin Falling Input during GTIOCA Value Low Source Counter Clear Enable
bits : 14 - 13 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter clear on the falling edge of GTIOCB input when GTIOCA input is 0
#1 : 1
Enable counter clear on the falling edge of GTIOCB input when GTIOCA input is 0
End of enumeration elements list.
CSCBFAH : GTIOCB Pin Falling Input during GTIOCA Value High Source Counter Clear Enable
bits : 15 - 14 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter clear on the falling edge of GTIOCB input when GTIOCA input is 1
#1 : 1
Enable counter clear on the falling edge of GTIOCB input when GTIOCA input is 1
End of enumeration elements list.
CSELCA : ELC_GPTA Event Source Counter Clear Enable
bits : 16 - 15 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter clear on ELC_GPTA input
#1 : 1
Enable counter clear on ELC_GPTA input
End of enumeration elements list.
CSELCB : ELC_GPTB Event Source Counter Clear Enable
bits : 17 - 16 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter clear on ELC_GPTB input
#1 : 1
Enable counter clear on ELC_GPTB input
End of enumeration elements list.
CSELCC : ELC_GPTC Event Source Counter Clear Enable
bits : 18 - 17 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter clear on ELC_GPTC input
#1 : 1
Enable counter clear on ELC_GPTC input
End of enumeration elements list.
CSELCD : ELC_GPTD Event Source Counter Clear Enable
bits : 19 - 18 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter clear on ELC_GPTD input
#1 : 1
Enable counter clear on ELC_GPTD input
End of enumeration elements list.
CSELCE : ELC_GPTE Event Source Counter Clear Enable
bits : 20 - 19 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter clear on ELC_GPTE input
#1 : 1
Enable counter clear on ELC_GPTE input
End of enumeration elements list.
CSELCF : ELC_GPTF Event Source Counter Clear Enable
bits : 21 - 20 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter clear on ELC_GPTF input
#1 : 1
Enable counter clear on ELC_GPTF input
End of enumeration elements list.
CSELCG : ELC_GPTG Event Source Counter Clear Enable
bits : 22 - 21 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter clear on ELC_GPTG input
#1 : 1
Enable counter clear on ELC_GPTG input
End of enumeration elements list.
CSELCH : ELC_GPTH Event Source Counter Clear Enable
bits : 23 - 22 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter clear on ELC_GPTH input
#1 : 1
Enable counter clear on ELC_GPTH input
End of enumeration elements list.
Reserved : These bits are read as 0000000. The write value should be 0000000.
bits : 24 - 29 (6 bit)
access : read-write
CCLR : Software Source Counter Clear Enable
bits : 31 - 30 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter clear by the GTCLR register
#1 : 1
Enable counter clear by the GTCLR register
End of enumeration elements list.
General PWM Timer Up Count Source Select Register
address_offset : 0x1C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
USGTRGAR : GTETRGA Pin Rising Input Source Counter Count Up Enable
bits : 0 - -1 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter count up on the rising edge of GTETRGA input
#1 : 1
Enable counter count up on the rising edge of GTETRGA input
End of enumeration elements list.
USGTRGAF : GTETRGA Pin Falling Input Source Counter Count Up Enable
bits : 1 - 0 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter count up on the falling edge of GTETRGA input
#1 : 1
Enable counter count up on the falling edge of GTETRGA input.
End of enumeration elements list.
USGTRGBR : GTETRGB Pin Rising Input Source Counter Count Up Enable
bits : 2 - 1 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter count up on the rising edge of GTETRGB input
#1 : 1
Enable counter count up on the rising edge of GTETRGB input.
End of enumeration elements list.
USGTRGBF : GTETRGB Pin Falling Input Source Counter Count Up Enable
bits : 3 - 2 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter count up on the falling edge of GTETRGB input
#1 : 1
Enable counter count up on the falling edge of GTETRGB input.
End of enumeration elements list.
USGTRGCR : GTETRGC Pin Rising Input Source Counter Count Up Enable
bits : 4 - 3 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter count up on the rising edge of GTETRGC input
#1 : 1
Enable counter count up on the rising edge of GTETRGC input
End of enumeration elements list.
USGTRGCF : GTETRGC Pin Falling Input Source Counter Count Up Enable
bits : 5 - 4 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter count up on the falling edge of GTETRGC input
#1 : 1
Enable counter count up on the falling edge of GTETRGC input.
End of enumeration elements list.
USGTRGDR : GTETRGD Pin Rising Input Source Counter Count Up Enable
bits : 6 - 5 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter count up on the rising edge of GTETRGD input
#1 : 1
Enable counter count up on the rising edge of GTETRGD input
End of enumeration elements list.
USGTRGDF : GTETRGD Pin Falling Input Source Counter Count Up Enable
bits : 7 - 6 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter count up on the falling edge of GTETRGD input
#1 : 1
Enable counter count up on the falling edge of GTETRGD input.
End of enumeration elements list.
USCARBL : GTIOCA Pin Rising Input during GTIOCB Value Low Source Counter Count Up Enable
bits : 8 - 7 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter count up on the rising edge of GTIOCA input when GTIOCB input is 0
#1 : 1
Enable counter count up on the rising edge of GTIOCA input when GTIOCB input is 0.
End of enumeration elements list.
USCARBH : GTIOCA Pin Rising Input during GTIOCB Value High Source Counter Count Up Enable
bits : 9 - 8 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter count up on the rising edge of GTIOCA input when GTIOCB input is 1
#1 : 1
Enable counter count up on the rising edge of GTIOCA input when GTIOCB input is 1.
End of enumeration elements list.
USCAFBL : GTIOCA Pin Falling Input during GTIOCB Value Low Source Counter Count Up Enable
bits : 10 - 9 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter count up on the falling edge of GTIOCA input when GTIOCB input is 0
#1 : 1
Enable counter count up on the falling edge of GTIOCA input when GTIOCB input is 0.
End of enumeration elements list.
USCAFBH : GTIOCA Pin Falling Input during GTIOCB Value High Source Counter Count Up Enable
bits : 11 - 10 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter count up on the falling edge of GTIOCA input when GTIOCB input is 1
#1 : 1
Enable counter count up on the falling edge of GTIOCA input when GTIOCB input is 1.
End of enumeration elements list.
USCBRAL : GTIOCB Pin Rising Input during GTIOCA Value Low Source Counter Count Up Enable
bits : 12 - 11 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter count up on the rising edge of GTIOCB input when GTIOCA input is 0
#1 : 1
Enable counter count up on the rising edge of GTIOCB input when GTIOCA input is 0.
End of enumeration elements list.
USCBRAH : GTIOCB Pin Rising Input during GTIOCA Value High Source Counter Count Up Enable
bits : 13 - 12 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter count up on the rising edge of GTIOCB input when GTIOCA input is 1
#1 : 1
Enable counter count up on the rising edge of GTIOCB input when GTIOCA input is 1.
End of enumeration elements list.
USCBFAL : GTIOCB Pin Falling Input during GTIOCA Value Low Source Counter Count Up Enable
bits : 14 - 13 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter count up on the falling edge of GTIOCB input when GTIOCA input is 0
#1 : 1
Enable counter count up on the falling edge of GTIOCB input when GTIOCA input is 0.
End of enumeration elements list.
USCBFAH : GTIOCB Pin Falling Input during GTIOCA Value High Source Counter Count Up Enable
bits : 15 - 14 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter count up on the falling edge of GTIOCB input when GTIOCA input is 1
#1 : 1
Enable counter count up on the falling edge of GTIOCB input when GTIOCA input is 1.
End of enumeration elements list.
USELCA : ELC_GPTA Event Source Counter Count Up Enable
bits : 16 - 15 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter count up on ELC_GPTA input
#1 : 1
Enable counter count up on ELC_GPTA input.
End of enumeration elements list.
USELCB : ELC_GPTB Event Source Counter Count Up Enable
bits : 17 - 16 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter count up on ELC_GPTB input
#1 : 1
Enable counter count up on ELC_GPTB input.
End of enumeration elements list.
USELCC : ELC_GPTC Event Source Counter Count Up Enable
bits : 18 - 17 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter count up on ELC_GPTC input
#1 : 1
Enable counter count up on ELC_GPTC input.
End of enumeration elements list.
USELCD : ELC_GPTD Event Source Counter Count Up Enable
bits : 19 - 18 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter count up on ELC_GPTD input
#1 : 1
Enable counter count up on ELC_GPTD input
End of enumeration elements list.
USELCE : ELC_GPTE Event Source Counter Count Up Enable
bits : 20 - 19 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter count up on ELC_GPTE input
#1 : 1
Enable counter count up on ELC_GPTE input.put
End of enumeration elements list.
USELCF : ELC_GPTF Event Source Counter Count Up Enable
bits : 21 - 20 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter count up on ELC_GPTF input
#1 : 1
Enable counter count up on ELC_GPTF input.
End of enumeration elements list.
USELCG : ELC_GPTG Event Source Counter Count Up Enable
bits : 22 - 21 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter count up on ELC_GPTG input
#1 : 1
Enable counter count up on ELC_GPTG input.
End of enumeration elements list.
USELCH : ELC_GPTH Event Source Counter Count Up Enable
bits : 23 - 22 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter count up on ELC_GPTH input
#1 : 1
Enable counter count up on ELC_GPTH input.
End of enumeration elements list.
Reserved : These bits are read as 00000000. The write value should be 00000000.
bits : 24 - 30 (7 bit)
access : read-write
General PWM Timer Down Count Source Select Register
address_offset : 0x20 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DSGTRGAR : GTETRGA Pin Rising Input Source Counter Count Down Enable
bits : 0 - -1 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter count down on the rising edge of GTETRGA input
#1 : 1
Enable counter count down on the rising edge of GTETRGA input
End of enumeration elements list.
DSGTRGAF : GTETRGA Pin Falling Input Source Counter Count Down Enable
bits : 1 - 0 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter count down on the falling edge of GTETRGA input
#1 : 1
Enable counter count down on the falling edge of GTETRGA input.
End of enumeration elements list.
DSGTRGBR : GTETRGB Pin Rising Input Source Counter Count Down Enable
bits : 2 - 1 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter count down on the rising edge of GTETRGB input
#1 : 1
Enable counter count down on the rising edge of GTETRGB input.
End of enumeration elements list.
DSGTRGBF : GTETRGB Pin Falling Input Source Counter Count Down Enable
bits : 3 - 2 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter count down on the falling edge of GTETRGB input
#1 : 1
Enable counter count down on the falling edge of GTETRGB input.
End of enumeration elements list.
DSGTRGCR : GTETRGC Pin Rising Input Source Counter Count Down Enable
bits : 4 - 3 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter count down on the rising edge of GTETRGC input
#1 : 1
Enable counter count down on the rising edge of GTETRGC input
End of enumeration elements list.
DSGTRGCF : GTETRGC Pin Falling Input Source Counter Count Down Enable
bits : 5 - 4 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter count down on the falling edge of GTETRGC input
#1 : 1
Enable counter count down on the falling edge of GTETRGC input.
End of enumeration elements list.
DSGTRGDR : GTETRGD Pin Rising Input Source Counter Count Down Enable
bits : 6 - 5 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter count down on the rising edge of GTETRGD input
#1 : 1
Enable counter count down on the rising edge of GTETRGD input.
End of enumeration elements list.
DSGTRGDF : GTETRGD Pin Falling Input Source Counter Count Down Enable
bits : 7 - 6 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter count down on the falling edge of GTETRGD input
#1 : 1
Enable counter count down on the falling edge of GTETRGD input.
End of enumeration elements list.
DSCARBL : GTIOCA Pin Rising Input during GTIOCB Value Low Source Counter Count Down Enable
bits : 8 - 7 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter count down on the rising edge of GTIOCA input when GTIOCB input is 0
#1 : 1
Enable counter count down on the rising edge of GTIOCA input when GTIOCB input is 0.
End of enumeration elements list.
DSCARBH : GTIOCA Pin Rising Input during GTIOCB Value High Source Counter Count Down Enable
bits : 9 - 8 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter count down on the rising edge of GTIOCA input when GTIOCB input is 1
#1 : 1
Enable counter count down on the rising edge of GTIOCA input when GTIOCB input is 1.
End of enumeration elements list.
DSCAFBL : GTIOCA Pin Falling Input during GTIOCB Value Low Source Counter Count Down Enable
bits : 10 - 9 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter count down on the falling edge of GTIOCA input when GTIOCB input is 0
#1 : 1
Enable counter count down on the falling edge of GTIOCA input when GTIOCB input is 0
End of enumeration elements list.
DSCAFBH : GTIOCA Pin Falling Input during GTIOCB Value High Source Counter Count Down Enable
bits : 11 - 10 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter count down on the falling edge of GTIOCA input when GTIOCB input is 1
#1 : 1
Enable counter count down on the falling edge of GTIOCA input when GTIOCB input is 1.
End of enumeration elements list.
DSCBRAL : GTIOCB Pin Rising Input during GTIOCA Value Low Source Counter Count Down Enable
bits : 12 - 11 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter count down on the rising edge of GTIOCB input when GTIOCA input is 0
#1 : 1
Enable counter count down on the rising edge of GTIOCB input when GTIOCA input is 0.
End of enumeration elements list.
DSCBRAH : GTIOCB Pin Rising Input during GTIOCA Value High Source Counter Count Down Enable
bits : 13 - 12 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter count down on the rising edge of GTIOCB input when GTIOCA input is 1
#1 : 1
Enable counter count down on the rising edge of GTIOCB input when GTIOCA input is 1.
End of enumeration elements list.
DSCBFAL : GTIOCB Pin Falling Input during GTIOCA Value Low Source Counter Count Down Enable
bits : 14 - 13 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter count down on the falling edge of GTIOCB input when GTIOCA input is 0
#1 : 1
Enable counter count down on the falling edge of GTIOCB input when GTIOCA input is 0.
End of enumeration elements list.
DSCBFAH : GTIOCB Pin Falling Input during GTIOCA Value High Source Counter Count Down Enable
bits : 15 - 14 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter count down on the falling edge of GTIOCB input when GTIOCA input is 1
#1 : 1
Enable counter count down on the falling edge of GTIOCB input when GTIOCA input is 1.
End of enumeration elements list.
DSELCA : ELC_GPTA Event Source Counter Count Down Enable
bits : 16 - 15 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter count down on ELC_GPTA input
#1 : 1
Enable counter count down on ELC_GPTA input.
End of enumeration elements list.
DSELCB : ELC_GPTB Event Source Counter Count Down Enable
bits : 17 - 16 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter count down on ELC_GPTB input
#1 : 1
Enable counter count down on ELC_GPTB input.
End of enumeration elements list.
DSELCC : ELC_GPTC Event Source Counter Count Down Enable
bits : 18 - 17 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter count down on ELC_GPTC input
#1 : 1
Enable counter count down on ELC_GPTC input.
End of enumeration elements list.
DSELCD : ELC_GPTD Event Source Counter Count Down Enable
bits : 19 - 18 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter count down on ELC_GPTD input
#1 : 1
Enable counter count down on ELC_GPTD input.
End of enumeration elements list.
DSELCE : ELC_GPTE Event Source Counter Count Down Enable
bits : 20 - 19 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter count down on ELC_GPTE input
#1 : 1
Enable counter count down on ELC_GPTE input.
End of enumeration elements list.
DSELCF : ELC_GPTF Event Source Counter Count Down Enable
bits : 21 - 20 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter count down on ELC_GPTF input
#1 : 1
Enable counter count down on ELC_GPTF input.
End of enumeration elements list.
DSELCG : ELC_GPTG Event Source Counter Count Down Enable
bits : 22 - 21 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter count down on ELC_GPTG input
#1 : 1
Enable counter count down on ELC_GPTG input.
End of enumeration elements list.
DSELCH : ELC_GPTH Event Source Counter Count Down Enable
bits : 23 - 22 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable counter count down on ELC_GPTH input
#1 : 1
Enable counter count down on ELC_GPTH input.
End of enumeration elements list.
Reserved : These bits are read as 00000000. The write value should be 00000000.
bits : 24 - 30 (7 bit)
access : read-write
General PWM Timer Input Capture Source Select Register A
address_offset : 0x24 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
ASGTRGAR : GTETRGA Pin Rising Input Source GTCCRA Input Capture Enable
bits : 0 - -1 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable GTCCRA input capture on the rising edge of GTETRGA input
#1 : 1
Enable GTCCRA input capture on the rising edge of GTETRGA input.
End of enumeration elements list.
ASGTRGAF : GTETRGA Pin Falling Input Source GTCCRA Input Capture Enable
bits : 1 - 0 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable GTCCRA input capture on the falling edge of GTETRGA input
#1 : 1
Enable GTCCRA input capture on the falling edge of GTETRGA input.
End of enumeration elements list.
ASGTRGBR : GTETRGB Pin Rising Input Source GTCCRA Input Capture Enable
bits : 2 - 1 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable GTCCRA input capture on the rising edge of GTETRGB input
#1 : 1
Enable GTCCRA input capture on the rising edge of GTETRGB input.
End of enumeration elements list.
ASGTRGBF : GTETRGB Pin Falling Input Source GTCCRA Input Capture Enable
bits : 3 - 2 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable GTCCRA input capture on the falling edge of GTETRGB input
#1 : 1
Enable GTCCRA input capture on the falling edge of GTETRGB input.
End of enumeration elements list.
ASGTRGCR : GTETRGC Pin Rising Input Source GTCCRA Input Capture Enable
bits : 4 - 3 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable GTCCRA input capture on the rising edge of GTETRGC input
#1 : 1
Enable GTCCRA input capture on the rising edge of GTETRGC input.
End of enumeration elements list.
ASGTRGCF : GTETRGC Pin Falling Input Source GTCCRA Input Capture Enable
bits : 5 - 4 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable GTCCRA input capture on the falling edge of GTETRGC input
#1 : 1
Enable GTCCRA input capture on the falling edge of GTETRGC input
End of enumeration elements list.
ASGTRGDR : GTETRGD Pin Rising Input Source GTCCRA Input Capture Enable
bits : 6 - 5 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable GTCCRA input capture on the rising edge of GTETRGD input
#1 : 1
Enable GTCCRA input capture on the rising edge of GTETRGD input.
End of enumeration elements list.
ASGTRGDF : GTETRGD Pin Falling Input Source GTCCRA Input Capture Enable
bits : 7 - 6 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable GTCCRA input capture on the falling edge of GTETRGD input
#1 : 1
Enable GTCCRA input capture on the falling edge of GTETRGD input.
End of enumeration elements list.
ASCARBL : GTIOCA Pin Rising Input during GTIOCB Value Low Source GTCCRA Input Capture Enable
bits : 8 - 7 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable GTCCRA input capture on the rising edge of GTIOCA input when GTIOCB input is 0
#1 : 1
Enable GTCCRA input capture on the rising edge of GTIOCA input when GTIOCB input is 0.
End of enumeration elements list.
ASCARBH : GTIOCA Pin Rising Input during GTIOCB Value High Source GTCCRA Input Capture Enable
bits : 9 - 8 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable GTCCRA input capture on the rising edge of GTIOCA input when GTIOCB input is 1
#1 : 1
Enable GTCCRA input capture on the rising edge of GTIOCA input when GTIOCB input is 1.
End of enumeration elements list.
ASCAFBL : GTIOCA Pin Falling Input during GTIOCB Value Low Source GTCCRA Input Capture Enable
bits : 10 - 9 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable GTCCRA input capture on the falling edge of GTIOCA input when GTIOCB input is 0
#1 : 1
Enable GTCCRA input capture on the falling edge of GTIOCA input when GTIOCB input is 0.
End of enumeration elements list.
ASCAFBH : GTIOCA Pin Falling Input during GTIOCB Value High Source GTCCRA Input Capture Enable
bits : 11 - 10 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable GTCCRA input capture on the falling edge of GTIOCA input when GTIOCB input is 1
#1 : 1
Enable GTCCRA input capture on the falling edge of GTIOCA input when GTIOCB input is 1.
End of enumeration elements list.
ASCBRAL : GTIOCB Pin Rising Input during GTIOCA Value Low Source GTCCRA Input Capture Enable
bits : 12 - 11 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable GTCCRA input capture on the rising edge of GTIOCB input when GTIOCA input is 0
#1 : 1
Enable GTCCRA input capture on the rising edge of GTIOCB input when GTIOCA input is 0.
End of enumeration elements list.
ASCBRAH : GTIOCB Pin Rising Input during GTIOCA Value High Source GTCCRA Input Capture Enable
bits : 13 - 12 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable GTCCRA input capture on the rising edge of GTIOCB input when GTIOCA input is 1
#1 : 1
Enable GTCCRA input capture on the rising edge of GTIOCB input when GTIOCA input is 1.
End of enumeration elements list.
ASCBFAL : GTIOCB Pin Falling Input during GTIOCA Value Low Source GTCCRA Input Capture Enable
bits : 14 - 13 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable GTCCRA input capture on the falling edge of GTIOCB input when GTIOCA input is 0
#1 : 1
Enable GTCCRA input capture on the falling edge of GTIOCB input when GTIOCA input is 0.
End of enumeration elements list.
ASCBFAH : GTIOCB Pin Falling Input during GTIOCA Value High Source GTCCRA Input Capture Enable
bits : 15 - 14 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable GTCCRA input capture on the falling edge of GTIOCB input when GTIOCA input is 1
#1 : 1
Enable GTCCRA input capture on the falling edge of GTIOCB input when GTIOCA input is 1.
End of enumeration elements list.
ASELCA : ELC_GPTA Event Source GTCCRA Input Capture Enable
bits : 16 - 15 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable GTCCRA input capture on ELC_GPTA input
#1 : 1
Enable GTCCRA input capture on ELC_GPTA input.
End of enumeration elements list.
ASELCB : ELC_GPTB Event Source GTCCRA Input Capture Enable
bits : 17 - 16 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable GTCCRA input capture on ELC_GPTB input
#1 : 1
Enable GTCCRA input capture on ELC_GPTB input
End of enumeration elements list.
ASELCC : ELC_GPTC Event Source GTCCRA Input Capture Enable
bits : 18 - 17 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable GTCCRA input capture on ELC_GPTC input
#1 : 1
Enable GTCCRA input capture on ELC_GPTC input.
End of enumeration elements list.
ASELCD : ELC_GPTD Event Source GTCCRA Input Capture Enable
bits : 19 - 18 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable GTCCRA input capture on ELC_GPTD input
#1 : 1
Enable GTCCRA input capture on ELC_GPTD input.
End of enumeration elements list.
ASELCE : ELC_GPTE Event Source GTCCRA Input Capture Enable
bits : 20 - 19 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable GTCCRA input capture on ELC_GPTE input
#1 : 1
Enable GTCCRA input capture on ELC_GPTE input.
End of enumeration elements list.
ASELCF : ELC_GPTF Event Source GTCCRA Input Capture Enable
bits : 21 - 20 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable GTCCRA input capture on ELC_GPTF input
#1 : 1
Enable GTCCRA input capture on ELC_GPTF input.
End of enumeration elements list.
ASELCG : ELC_GPTG Event Source GTCCRA Input Capture Enable
bits : 22 - 21 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable GTCCRA input capture on ELC_GPTG input
#1 : 1
Enable GTCCRA input capture on ELC_GPTG input.
End of enumeration elements list.
ASELCH : ELC_GPTH Event Source GTCCRA Input Capture Enable
bits : 23 - 22 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable GTCCRA input capture on ELC_GPTH input
#1 : 1
Enable GTCCRA input capture on ELC_GPTH input
End of enumeration elements list.
Reserved : These bits are read as 00000000. The write value should be 00000000.
bits : 24 - 30 (7 bit)
access : read-write
General PWM Timer Input Capture Source Select Register B
address_offset : 0x28 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
BSGTRGAR : GTETRGA Pin Rising Input Source GTCCRB Input Capture Enable
bits : 0 - -1 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable GTCCRB input capture on the rising edge of GTETRGA input
#1 : 1
Enable GTCCRB input capture on the rising edge of GTETRGA input.
End of enumeration elements list.
BSGTRGAF : GTETRGA Pin Falling Input Source GTCCRB Input Capture Enable
bits : 1 - 0 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable GTCCRB input capture on the falling edge of GTETRGA input
#1 : 1
Enable GTCCRB input capture on the falling edge of GTETRGA input.
End of enumeration elements list.
BSGTRGBR : GTETRGB Pin Rising Input Source GTCCRB Input Capture Enable
bits : 2 - 1 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable GTCCRB input capture on the rising edge of GTETRGB input
#1 : 1
Enable GTCCRB input capture on the rising edge of GTETRGB input.
End of enumeration elements list.
BSGTRGBF : GTETRGB Pin Falling Input Source GTCCRB Input Capture Enable
bits : 3 - 2 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable GTCCRB input capture on the falling edge of GTETRGB input
#1 : 1
Enable GTCCRB input capture on the falling edge of GTETRGB input.
End of enumeration elements list.
BSGTRGCR : GTETRGC Pin Rising Input Source GTCCRB Input Capture Enable
bits : 4 - 3 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable GTCCRB input capture on the rising edge of GTETRGC input
#1 : 1
Enable GTCCRB input capture on the rising edge of GTETRGC input.
End of enumeration elements list.
BSGTRGCF : GTETRGC Pin Falling Input Source GTCCRB Input Capture Enable
bits : 5 - 4 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable GTCCRB input capture on the falling edge of GTETRGC input
#1 : 1
Enable GTCCRB input capture on the falling edge of GTETRGC input.
End of enumeration elements list.
BSGTRGDR : GTETRGD Pin Rising Input Source GTCCRB Input Capture Enable
bits : 6 - 5 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable GTCCRB input capture on the rising edge of GTETRGD input
#1 : 1
Enable GTCCRB input capture on the rising edge of GTETRGD input.
End of enumeration elements list.
BSGTRGDF : GTETRGD Pin Falling Input Source GTCCRB Input Capture Enable
bits : 7 - 6 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable GTCCRB input capture on the falling edge of GTETRGD input
#1 : 1
Enable GTCCRB input capture on the falling edge of GTETRGD input.
End of enumeration elements list.
BSCARBL : GTIOCA Pin Rising Input during GTIOCB Value Low Source GTCCRB Input Capture Enable
bits : 8 - 7 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable GTCCRB input capture on the rising edge of GTIOCA input when GTIOCB input is 0
#1 : 1
Enable GTCCRB input capture on the rising edge of GTIOCA input when GTIOCB input is 0.
End of enumeration elements list.
BSCARBH : GTIOCA Pin Rising Input during GTIOCB Value High Source GTCCRB Input Capture Enable
bits : 9 - 8 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable GTCCRB input capture on the rising edge of GTIOCA input when GTIOCB input is 1
#1 : 1
Enable GTCCRB input capture on the rising edge of GTIOCA input when GTIOCB input is 1.
End of enumeration elements list.
BSCAFBL : GTIOCA Pin Falling Input during GTIOCB Value Low Source GTCCRB Input Capture Enable
bits : 10 - 9 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable GTCCRB input capture on the falling edge of GTIOCA input when GTIOCB input is 0
#1 : 1
Enable GTCCRB input capture on the falling edge of GTIOCA input when GTIOCB input is 0.
End of enumeration elements list.
BSCAFBH : GTIOCA Pin Falling Input during GTIOCB Value High Source GTCCRB Input Capture Enable
bits : 11 - 10 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable GTCCRB input capture on the falling edge of GTIOCA input when GTIOCB input is 1
#1 : 1
Enable GTCCRB input capture on the falling edge of GTIOCA input when GTIOCB input is 1.
End of enumeration elements list.
BSCBRAL : GTIOCB Pin Rising Input during GTIOCA Value Low Source GTCCRB Input Capture Enable
bits : 12 - 11 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable GTCCRB input capture on the rising edge of GTIOCB input when GTIOCA input is 0
#1 : 1
Enable GTCCRB input capture on the rising edge of GTIOCB input when GTIOCA input is 0.
End of enumeration elements list.
BSCBRAH : GTIOCB Pin Rising Input during GTIOCA Value High Source GTCCRB Input Capture Enable
bits : 13 - 12 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable GTCCRB input capture on the rising edge of GTIOCB input when GTIOCA input is 1
#1 : 1
Enable GTCCRB input capture on the rising edge of GTIOCB input when GTIOCA input is 1.
End of enumeration elements list.
BSCBFAL : GTIOCB Pin Falling Input during GTIOCA Value Low Source GTCCRB Input Capture Enable
bits : 14 - 13 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable GTCCRB input capture on the falling edge of GTIOCB input when GTIOCA input is 0
#1 : 1
Enable GTCCRB input capture on the falling edge of GTIOCB input when GTIOCA input is 0.
End of enumeration elements list.
BSCBFAH : GTIOCB Pin Falling Input during GTIOCA Value High Source GTCCRB Input Capture Enable
bits : 15 - 14 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable GTCCRB input capture on the falling edge of GTIOCB input when GTIOCA input is 1
#1 : 1
Enable GTCCRB input capture on the falling edge of GTIOCB input when GTIOCA input is 1.
End of enumeration elements list.
BSELCA : ELC_GPTA Event Source GTCCRB Input Capture Enable
bits : 16 - 15 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable GTCCRB input capture on ELC_GPTA input
#1 : 1
Enable GTCCRB input capture on ELC_GPTA input.
End of enumeration elements list.
BSELCB : ELC_GPTB Event Source GTCCRB Input Capture Enable
bits : 17 - 16 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable GTCCRB input capture on ELC_GPTB input
#1 : 1
Enable GTCCRB input capture on ELC_GPTB input.
End of enumeration elements list.
BSELCC : ELC_GPTC Event Source GTCCRB Input Capture Enable
bits : 18 - 17 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable GTCCRB input capture on ELC_GPTC input
#1 : 1
Enable GTCCRB input capture on ELC_GPTC input
End of enumeration elements list.
BSELCD : ELC_GPTD Event Source GTCCRB Input Capture Enable
bits : 19 - 18 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable GTCCRB input capture on ELC_GPTD input
#1 : 1
Enable GTCCRB input capture on ELC_GPTD input.
End of enumeration elements list.
BSELCE : ELC_GPTE Event Source GTCCRB Input Capture Enable
bits : 20 - 19 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable GTCCRB input capture on ELC_GPTE input
#1 : 1
Enable GTCCRB input capture on ELC_GPTE input
End of enumeration elements list.
BSELCF : ELC_GPTF Event Source GTCCRB Input Capture Enable
bits : 21 - 20 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable GTCCRB input capture on ELC_GPTF input
#1 : 1
Enable GTCCRB input capture on ELC_GPTF input.
End of enumeration elements list.
BSELCG : ELC_GPTG Event Source GTCCRB Input Capture Enable
bits : 22 - 21 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable GTCCRB input capture on ELC_GPTG input
#1 : 1
Enable GTCCRB input capture on ELC_GPTG input.
End of enumeration elements list.
BSELCH : ELC_GPTH Event Source GTCCRB Input Capture Enable
bits : 23 - 22 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable GTCCRB input capture on ELC_GPTH input
#1 : 1
Enable GTCCRB input capture on ELC_GPTH input.
End of enumeration elements list.
Reserved : These bits are read as 00000000. The write value should be 00000000.
bits : 24 - 30 (7 bit)
access : read-write
General PWM Timer Control Register
address_offset : 0x2C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
CST : Count Start
bits : 0 - -1 (0 bit)
access : read-write
Enumeration:
#0 : 0
Count operation is stopped
#1 : 1
Count operation is performed
End of enumeration elements list.
Reserved : These bits are read as 000000000000000. The write value should be 000000000000000.
bits : 1 - 14 (14 bit)
access : read-write
Reserved : These bits are read as 000000000000000. The write value should be 000000000000000.
bits : 1 - 14 (14 bit)
access : read-write
MD : Mode Select
bits : 16 - 17 (2 bit)
access : read-write
Enumeration:
#000 : 000
Saw-wave PWM mode (single buffer or double buffer possible)
#001 : 001
Saw-wave one-shot pulse mode (fixed buffer operation)
#010 : 010
Setting prohibited
#011 : 011
Setting prohibited
#100 : 100
Triangle-wave PWM mode 1 (32-bit transfer at crest) (single buffer or double buffer possible)
#101 : 101
Triangle-wave PWM mode 2 (32-bit transfer at crest and trough) (single buffer or double buffer possible)
#110 : 110
Triangle-wave PWM mode 3 (64-bit transfer at trough) fixed buffer operation)
#111 : 111
Setting prohibited
End of enumeration elements list.
Reserved : These bits are read as 00000. The write value should be 00000.
bits : 19 - 22 (4 bit)
access : read-write
TPCS : Timer Prescaler Select
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
#000 : 000
PCLK/1
#001 : 001
PCLK/4
#010 : 010
PCLK/16
#011 : 011
PCLK/64
#100 : 100
PCLK/256
#101 : 101
PCLK/1024
: others
Setting prohibited
End of enumeration elements list.
General PWM Timer Count Direction and Duty Setting Register
address_offset : 0x30 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
UD : Count Direction Setting
bits : 0 - -1 (0 bit)
access : read-write
Enumeration:
#0 : 0
Count down on GTCNT
#1 : 1
Counts up on GTCNT
End of enumeration elements list.
UDF : Forcible Count Direction Setting
bits : 1 - 0 (0 bit)
access : read-write
Enumeration:
#0 : 0
Do not force setting
#1 : 1
Force setting
End of enumeration elements list.
Reserved : These bits are read as 00000000000000. The write value should be 00000000000000.
bits : 2 - 14 (13 bit)
access : read-write
Reserved : These bits are read as 00000000000000. The write value should be 00000000000000.
bits : 2 - 14 (13 bit)
access : read-write
OADTY : GTIOCA Output Duty Setting
bits : 16 - 16 (1 bit)
access : read-write
Enumeration:
#00 : 00
GTIOCA pin duty is depend on compare match
#01 : 01
GTIOCA pin duty is depend on compare match
#10 : 10
GTIOCA pin duty 0 percent
#11 : 11
GTIOCA pin duty 100 percent
End of enumeration elements list.
OADTYF : Forcible GTIOCA Output Duty Setting
bits : 18 - 17 (0 bit)
access : read-write
Enumeration:
#0 : 0
Do not force setting
#1 : 1
Force setting
End of enumeration elements list.
OADTYR : GTIOCA Output Value Selecting after Releasing 0 percent/100 percent Duty Setting
bits : 19 - 18 (0 bit)
access : read-write
Enumeration:
#0 : 0
Apply output value set in 0 percent/100 percent duty to GTIOA[3:2] function after releasing 0 percent/100 percent duty setting.
#1 : 1
Apply masked compare match output value to GTIOA[3:2] function after releasing 0 percent/100 percent duty setting.
End of enumeration elements list.
Reserved : These bits are read as 0000. The write value should be 0000.
bits : 20 - 22 (3 bit)
access : read-write
OBDTY : GTIOCB Output Duty Setting
bits : 24 - 24 (1 bit)
access : read-write
Enumeration:
#00 : 00
GTIOCB pin duty is depend on compare match
#01 : 01
GTIOCB pin duty is depend on compare match
#10 : 10
GTIOCB pin duty 0percent
#11 : 11
GTIOCB pin duty 100percent
End of enumeration elements list.
OBDTYF : Forcible GTIOCB Output Duty Setting
bits : 26 - 25 (0 bit)
access : read-write
Enumeration:
#0 : 0
Do not force setting
#1 : 1
Force setting
End of enumeration elements list.
OBDTYR : GTIOCB Output Value Selecting after Releasing 0 percent/100 percent Duty Setting
bits : 27 - 26 (0 bit)
access : read-write
Enumeration:
#0 : 0
Apply output value set in 0 percent/100 percent duty to GTIOB[3:2] function after releasing 0percent/100percent duty setting.
#1 : 1
Apply masked compare match output value to GTIOB[3:2] function after releasing 0percent/100percent duty setting.
End of enumeration elements list.
General PWM Timer I/O Control Register
address_offset : 0x34 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
GTIOA : GTIOCA Pin Function Select
bits : 0 - 3 (4 bit)
access : read-write
Enumeration:
#00000 : 00000
Initial output is Low. Output retained at cycle end. Output retained at GTCCRA compare match.
#00001 : 00001
Initial output is Low. Output retained at cycle end. Low output at GTCCRA compare match.
#00010 : 00010
Initial output is Low. Output retained at cycle end. High output at GTCCRA compare match.
#00011 : 00011
Initial output is Low. Output retained at cycle end. Output toggled at GTCCRA compare match.
#00100 : 00100
Initial output is Low. Low output at cycle end. Output retained at GTCCRA compare match.
#00101 : 00101
Initial output is Low. Low output at cycle end. Low output at GTCCRA compare match.
#00110 : 00110
Initial output is Low. Low output at cycle end. High output at GTCCRA compare match.
#00111 : 00111
Initial output is Low. Low output at cycle end. Output toggled at GTCCRA compare match.
#01000 : 01000
Initial output is Low. High output at cycle end. Output retained at GTCCRA compare match.
#01001 : 01001
Initial output is Low. High output at cycle end. Low output at GTCCRA compare match.
#01010 : 01010
Initial output is Low. High output at cycle end. High output at GTCCRA compare match.
#01011 : 01011
Initial output is Low. High output at cycle end. Output toggled at GTCCRA compare match.
#01100 : 01100
Initial output is Low. Output toggled at cycle end. Output retained at GTCCRA compare match.
#01101 : 01101
Initial output is Low. Output toggled at cycle end. Low output at GTCCRA compare match.
#01110 : 01110
Initial output is Low. Output toggled at cycle end. High output at GTCCRA compare match.
#01111 : 01111
Initial output is Low. Output toggled at cycle end. Output toggled at GTCCRA compare match.
#10000 : 10000
Initial output is High. Output retained at cycle end. Output retained at GTCCRA compare match.
#10001 : 10001
Initial output is High. Output retained at cycle end. Low output at GTCCRA compare match.
#10010 : 10010
Initial output is High. Output retained at cycle end. High output at GTCCRA compare match.
#10011 : 10011
Initial output is High. Output retained at cycle end. Output toggled at GTCCRA compare match.
#10100 : 10100
Initial output is High. Low output at cycle end. Output retained at GTCCRA compare match.
#10101 : 10101
Initial output is High. Low output at cycle end. Low output at GTCCRA compare match.
#10110 : 10110
Initial output is High. Low output at cycle end. High output at GTCCRA compare match.
#10111 : 10111
Initial output is High. Low output at cycle end. Output toggled at GTCCRA compare match.
#11000 : 11000
Initial output is High. High output at cycle end. Output retained at GTCCRA compare match.
#11001 : 11001
Initial output is High. High output at cycle end. Low output at GTCCRA compare match.
#11010 : 11010
Initial output is High. High output at cycle end. High output at GTCCRA compare match.
#11011 : 11011
Initial output is High. High output at cycle end. Output toggled at GTCCRA compare match.
#11100 : 11100
Initial output is High. Output toggled at cycle end. Output retained at GTCCRA compare match.
#11101 : 11101
Initial output is High. Output toggled at cycle end. Low output at GTCCRA compare match.
#11110 : 11110
Initial output is High. Output toggled at cycle end. High output at GTCCRA compare match.
#11111 : 11111
Initial output is High. Output toggled at cycle end. Output toggled at GTCCRA compare match.
End of enumeration elements list.
Reserved : This bit is read as 0. The write value should be 0.
bits : 5 - 4 (0 bit)
access : read-write
Reserved : This bit is read as 0. The write value should be 0.
bits : 5 - 4 (0 bit)
access : read-write
OADFLT : GTIOCA Pin Output Value Setting at the Count Stop
bits : 6 - 5 (0 bit)
access : read-write
Enumeration:
#0 : 0
Output low on GTIOCA pin when counting stops
#1 : 1
Output high on GTIOCA pin when counting stops.
End of enumeration elements list.
OAHLD : GTIOCA Pin Output Setting at the Start/Stop Count
bits : 7 - 6 (0 bit)
access : read-write
Enumeration:
#0 : 0
Set GTIOCA pin output level on counting start and stop based on the register setting.
#1 : 1
Retain GTIOCA pin output level on counting start and stop
End of enumeration elements list.
OAE : GTIOCA Pin Output Enable
bits : 8 - 7 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable output
#1 : 1
Enable output.
End of enumeration elements list.
OADF : GTIOCA Pin Disable Value Setting
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#00 : 00
Prohibit output disable
#01 : 01
Set GTIOCA pin to Hi-Z on output disable
#10 : 10
Set GTIOCA pin to 0 on output disable
#11 : 11
Set GTIOCA pin to 1 on output disable.
End of enumeration elements list.
Reserved : These bits are read as 00. The write value should be 00.
bits : 11 - 11 (1 bit)
access : read-write
NFAEN : Noise Filter A Enable
bits : 13 - 12 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable noise filter for GTIOCA pin
#1 : 1
Enable noise filter for GTIOCA pin.
End of enumeration elements list.
NFCSA : Noise Filter A Sampling Clock Select
bits : 14 - 14 (1 bit)
access : read-write
Enumeration:
#00 : 00
PCLK/1
#01 : 01
PCLK/4
#10 : 10
PCLK/16
#11 : 11
PCLK/64
End of enumeration elements list.
GTIOB : GTIOCB Pin Function Select
bits : 16 - 19 (4 bit)
access : read-write
Enumeration:
#00000 : 00000
Initial output is Low. Output retained at cycle end. Output retained at GTCCRB compare match.
#00001 : 00001
Initial output is Low. Output retained at cycle end. Low output at GTCCRB compare match.
#00010 : 00010
Initial output is Low. Output retained at cycle end. High output at GTCCRB compare match.
#00011 : 00011
Initial output is Low. Output retained at cycle end. Output toggled at GTCCRB compare match.
#00100 : 00100
Initial output is Low. Low output at cycle end. Output retained at GTCCRB compare match.
#00101 : 00101
Initial output is Low. Low output at cycle end. Low output at GTCCRB compare match.
#00110 : 00110
Initial output is Low. Low output at cycle end. High output at GTCCRB compare match.
#00111 : 00111
Initial output is Low. Low output at cycle end. Output toggled at GTCCRB compare match.
#01000 : 01000
Initial output is Low. High output at cycle end. Output retained at GTCCRB compare match.
#01001 : 01001
Initial output is Low. High output at cycle end. Low output at GTCCRB compare match.
#01010 : 01010
Initial output is Low. High output at cycle end. High output at GTCCRB compare match.
#01011 : 01011
Initial output is Low. High output at cycle end. Output toggled at GTCCRB compare match.
#01100 : 01100
Initial output is Low. Output toggled at cycle end. Output retained at GTCCRB compare match.
#01101 : 01101
Initial output is Low. Output toggled at cycle end. Low output at GTCCRB compare match.
#01110 : 01110
Initial output is Low. Output toggled at cycle end. High output at GTCCRB compare match.
#01111 : 01111
Initial output is Low. Output toggled at cycle end. Output toggled at GTCCRB compare match.
#10000 : 10000
Initial output is High. Output retained at cycle end. Output retained at GTCCRB compare match.
#10001 : 10001
Initial output is High. Output retained at cycle end. Low output at GTCCRB compare match.
#10010 : 10010
Initial output is High. Output retained at cycle end. High output at GTCCRB compare match.
#10011 : 10011
Initial output is High. Output retained at cycle end. Output toggled at GTCCRB compare match.
#10100 : 10100
Initial output is High. Low output at cycle end. Output retained at GTCCRB compare match.
#10101 : 10101
Initial output is High. Low output at cycle end. Low output at GTCCRB compare match.
#10110 : 10110
Initial output is High. Low output at cycle end. High output at GTCCRB compare match.
#10111 : 10111
Initial output is High. Low output at cycle end. Output toggled at GTCCRB compare match.
#11000 : 11000
Initial output is High. High output at cycle end. Output retained at GTCCRB compare match.
#11001 : 11001
Initial output is High. High output at cycle end. Low output at GTCCRB compare match.
#11010 : 11010
Initial output is High. High output at cycle end. High output at GTCCRB compare match.
#11011 : 11011
Initial output is High. High output at cycle end. Output toggled at GTCCRB compare match.
#11100 : 11100
Initial output is High. Output toggled at cycle end. Output retained at GTCCRB compare match.
#11101 : 11101
Initial output is High. Output toggled at cycle end. Low output at GTCCRB compare match.
#11110 : 11110
Initial output is High. Output toggled at cycle end. High output at GTCCRB compare match.
#11111 : 11111
Initial output is High. Output toggled at cycle end. Output toggled at GTCCRB compare match.
End of enumeration elements list.
Reserved : This bit is read as 0. The write value should be 0.
bits : 21 - 20 (0 bit)
access : read-write
OBDFLT : GTIOCB Pin Output Value Setting at the Count Stop
bits : 22 - 21 (0 bit)
access : read-write
Enumeration:
#0 : 0
Output low on GTIOCB pin when counting stops
#1 : 1
Output high on GTIOCB pin when counting stops
End of enumeration elements list.
OBHLD : GTIOCB Pin Output Setting at the Start/Stop Count
bits : 23 - 22 (0 bit)
access : read-write
Enumeration:
#0 : 0
Set GTIOCB pin output level on counting start and stop based on the register setting
#1 : 1
Retain GTIOCB pin output level on counting start and stop
End of enumeration elements list.
OBE : GTIOCB Pin Output Enable
bits : 24 - 23 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable output
#1 : 1
Enable output
End of enumeration elements list.
OBDF : GTIOCB Pin Disable Value Setting
bits : 25 - 25 (1 bit)
access : read-write
Enumeration:
#00 : 00
Prohibit output disable
#01 : 01
Set GTIOCB pin to Hi-Z on output disable
#10 : 10
Set GTIOCB pin to 0 on output disable
#11 : 11
Set GTIOCB pin to 1 on output disable.
End of enumeration elements list.
NFBEN : Noise Filter B Enable
bits : 29 - 28 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable noise filter for GTIOCB pin
#1 : 1
Enable noise filter for GTIOCB pin
End of enumeration elements list.
NFCSB : Noise Filter B Sampling Clock Select
bits : 30 - 30 (1 bit)
access : read-write
Enumeration:
#00 : 00
PCLK/1
#01 : 01
PCLK/4
#10 : 10
PCLK/16
#11 : 11
PCLK/64
End of enumeration elements list.
General PWM Timer Interrupt Output Setting Register
address_offset : 0x38 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
Reserved : These bits are read as 000000000000000000000000. The write value should be 000000000000000000000000.
bits : 0 - 22 (23 bit)
access : read-write
Reserved : These bits are read as 000000000000000000000000. The write value should be 000000000000000000000000.
bits : 0 - 22 (23 bit)
access : read-write
GRP : Output Disable Source Select
bits : 24 - 24 (1 bit)
access : read-write
Enumeration:
#00 : 00
Select Group A output disable request
#01 : 01
Select Group B output disable request
#10 : 10
Select Group C output disable request
#11 : 11
Select Group D output disable request.
End of enumeration elements list.
Reserved : These bits are read as 000. The write value should be 000.
bits : 26 - 27 (2 bit)
access : read-write
GRPABH : Same Time Output Level High Disable Request Enable
bits : 29 - 28 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable same time output level high disable request
#1 : 1
Enable same time output level high disable request
End of enumeration elements list.
GRPABL : Same Time Output Level Low Disable Request Enable
bits : 30 - 29 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disable same time output level low disable request
#1 : 1
Enable same time output level low disable request
End of enumeration elements list.
General PWM Timer Status Register
address_offset : 0x3C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TCFA : Input Capture/Compare Match Flag A
bits : 0 - -1 (0 bit)
access : read-write
Enumeration:
#0 : 0
No input capture/compare match of GTCCRA is generated.
#1 : 1
An input capture/compare match of GTCCRA is generated.
End of enumeration elements list.
TCFB : Input Capture/Compare Match Flag B
bits : 1 - 0 (0 bit)
access : read-write
Enumeration:
#0 : 0
No input capture/compare match of GTCCRB is generated.
#1 : 1
An input capture/compare match of GTCCRB is generated.
End of enumeration elements list.
TCFC : Input Compare Match Flag C
bits : 2 - 1 (0 bit)
access : read-write
Enumeration:
#0 : 0
No compare match of GTCCRC is generated.
#1 : 1
A compare match of GTCCRC is generated.
End of enumeration elements list.
TCFD : Input Compare Match Flag D
bits : 3 - 2 (0 bit)
access : read-write
Enumeration:
#0 : 0
No compare match of GTCCRD is generated.
#1 : 1
A compare match of GTCCRD is generated.
End of enumeration elements list.
TCFE : Input Compare Match Flag E
bits : 4 - 3 (0 bit)
access : read-write
Enumeration:
#0 : 0
No compare match of GTCCRE is generated.
#1 : 1
A compare match of GTCCRE is generated.
End of enumeration elements list.
TCFF : Input Compare Match Flag F
bits : 5 - 4 (0 bit)
access : read-write
Enumeration:
#0 : 0
No compare match of GTCCRF is generated.
#1 : 1
A compare match of GTCCRF is generated.
End of enumeration elements list.
TCFPO : Overflow Flag
bits : 6 - 5 (0 bit)
access : read-write
Enumeration:
#0 : 0
No overflow (crest) has occurred.
#1 : 1
An overflow (crest) has occurred.
End of enumeration elements list.
TCFPU : Underflow Flag
bits : 7 - 6 (0 bit)
access : read-write
Enumeration:
#0 : 0
No underflow (trough) has occurred.
#1 : 1
An underflow (trough) has occurred.
End of enumeration elements list.
Reserved : These bits are read as 0000000. The write value should be 0000000.
bits : 8 - 13 (6 bit)
access : read-write
Reserved : These bits are read as 0000000. The write value should be 0000000.
bits : 8 - 13 (6 bit)
access : read-write
TUCF : Count Direction Flag
bits : 15 - 14 (0 bit)
access : read-only
Enumeration:
#0 : 0
GTCNT counter is counting down
#1 : 1
GTCNT counter is counting up.
End of enumeration elements list.
Reserved : These bits are read as 00000000. The write value should be 00000000.
bits : 16 - 22 (7 bit)
access : read-write
ODF : Output Disable Flag
bits : 24 - 23 (0 bit)
access : read-only
Enumeration:
#0 : 0
No output disable request is generated.
#1 : 1
An output disable request is generated.
End of enumeration elements list.
Reserved : These bits are read as 0000. The write value should be 0000.
bits : 25 - 27 (3 bit)
access : read-write
OABHF : Same Time Output Level High Disable Request Enable
bits : 29 - 28 (0 bit)
access : read-only
Enumeration:
#0 : 0
GTIOCA pin and GTIOCB pin don't output 1 at the same time.
#1 : 1
GTIOCA pin and GTIOCB pin output 1 at the same time.
End of enumeration elements list.
OABLF : Same Time Output Level Low Disable Request Enable
bits : 30 - 29 (0 bit)
access : read-only
Enumeration:
#0 : 0
GTIOCA pin and GTIOCB pin don't output 0 at the same time.
#1 : 1
GTIOCA pin and GTIOCB pin output 0 at the same time.
End of enumeration elements list.
General PWM Timer Software Start Register
address_offset : 0x4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
CSTRT0 : Channel 0 GTCNT Count Start Read data shows each channel's counter status (GTCR.CST bit). 0 means counter stop. 1 means counter running.
bits : 0 - -1 (0 bit)
access : read-write
Enumeration:
#0 : 0
No effect (write) / counter stop (read)
#1 : 1
GPT32EH0.GTCNT counter starts (write) / Counter running (read)
End of enumeration elements list.
CSTRT1 : Channel 1 GTCNT Count Start Read data shows each channel's counter status (GTCR.CST bit). 0 means counter stop. 1 means counter running.
bits : 1 - 0 (0 bit)
access : read-write
Enumeration:
#0 : 0
No effect (write) / counter stop (read)
#1 : 1
GPT32EH1.GTCNT counter starts (write) / Counter running (read)
End of enumeration elements list.
CSTRT2 : Channel 2 GTCNT Count Start Read data shows each channel's counter status (GTCR.CST bit). 0 means counter stop. 1 means counter running.
bits : 2 - 1 (0 bit)
access : read-write
Enumeration:
#0 : 0
No effect (write) / counter stop (read)
#1 : 1
GPT32EH2.GTCNT counter starts (write) / Counter running (read)
End of enumeration elements list.
CSTRT3 : Channel 3 GTCNT Count Start Read data shows each channel's counter status (GTCR.CST bit). 0 means counter stop. 1 means counter running.
bits : 3 - 2 (0 bit)
access : read-write
Enumeration:
#0 : 0
No effect (write) / counter stop (read)
#1 : 1
GPT32EH3.GTCNT counter starts (write) / Counter running (read)
End of enumeration elements list.
CSTRT4 : Channel 4 GTCNT Count Start Read data shows each channel's counter status (GTCR.CST bit). 0 means counter stop. 1 means counter running.
bits : 4 - 3 (0 bit)
access : read-write
Enumeration:
#0 : 0
No effect (write) / counter stop (read)
#1 : 1
GPT32E4.GTCNT counter starts (write) / Counter running (read)
End of enumeration elements list.
CSTRT5 : Channel 5 GTCNT Count Start Read data shows each channel's counter status (GTCR.CST bit). 0 means counter stop. 1 means counter running.
bits : 5 - 4 (0 bit)
access : read-write
Enumeration:
#0 : 0
No effect (write) / counter stop (read)
#1 : 1
GPT32E5.GTCNT counter starts (write) / Counter running (read)
End of enumeration elements list.
CSTRT6 : Channel 6 GTCNT Count Start Read data shows each channel's counter status (GTCR.CST bit). 0 means counter stop. 1 means counter running.
bits : 6 - 5 (0 bit)
access : read-write
Enumeration:
#0 : 0
No effect (write) / counter stop (read)
#1 : 1
GPT32E6.GTCNT counter starts (write) / Counter running (read)
End of enumeration elements list.
CSTRT7 : Channel 7 GTCNT Count Start Read data shows each channel's counter status (GTCR.CST bit). 0 means counter stop. 1 means counter running.
bits : 7 - 6 (0 bit)
access : read-write
Enumeration:
#0 : 0
No effect (write) / counter stop (read)
#1 : 1
GPT32E7.GTCNT counter starts (write) / Counter running (read)
End of enumeration elements list.
CSTRT8 : Channel 8 GTCNT Count Start Read data shows each channel's counter status (GTCR.CST bit). 0 means counter stop. 1 means counter running.
bits : 8 - 7 (0 bit)
access : read-write
Enumeration:
#0 : 0
No effect (write) / counter stop (read)
#1 : 1
GPT328.GTCNT counter starts (write) / Counter running (read)
End of enumeration elements list.
CSTRT9 : Channel 9 GTCNT Count Start Read data shows each channel's counter status (GTCR.CST bit). 0 means counter stop. 1 means counter running.
bits : 9 - 8 (0 bit)
access : read-write
Enumeration:
#0 : 0
No effect (write) / counter stop (read)
#1 : 1
GPT329.GTCNT counter starts (write) / Counter running (read)
End of enumeration elements list.
CSTRT10 : Channel 10 GTCNT Count Start Read data shows each channel's counter status (GTCR.CST bit). 0 means counter stop. 1 means counter running.
bits : 10 - 9 (0 bit)
access : read-write
Enumeration:
#0 : 0
No effect (write) / counter stop (read)
#1 : 1
GPT3210.GTCNT counter starts (write) / Counter running (read)
End of enumeration elements list.
CSTRT11 : Channel 11 GTCNT Count Start Read data shows each channel's counter status (GTCR.CST bit). 0 means counter stop. 1 means counter running.
bits : 11 - 10 (0 bit)
access : read-write
Enumeration:
#0 : 0
No effect (write) / counter stop (read)
#1 : 1
GPT3211.GTCNT counter starts (write) / Counter running (read)
End of enumeration elements list.
CSTRT12 : Channel 12 GTCNT Count Start Read data shows each channel's counter status (GTCR.CST bit). 0 means counter stop. 1 means counter running.
bits : 12 - 11 (0 bit)
access : read-write
Enumeration:
#0 : 0
No effect (write) / counter stop (read)
#1 : 1
GPT3212.GTCNT counter starts (write) / Counter running (read)
End of enumeration elements list.
Reserved : These bits are read as 0000000000000000000. The write value should be 0000000000000000000.
bits : 13 - 30 (18 bit)
access : read-write
General PWM Timer Buffer Enable Register
address_offset : 0x40 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
BD2 : GTCCR Buffer Operation Disable
bits : 0 - -1 (0 bit)
access : read-write
Enumeration:
#0 : 0
Enable buffer operation
#1 : 1
Disable buffer operation.
End of enumeration elements list.
BD1 : GTPR Buffer Operation Disable
bits : 1 - 0 (0 bit)
access : read-write
Enumeration:
#0 : 0
Enable buffer operation
#1 : 1
Disable buffer operation.
End of enumeration elements list.
Reserved : These bits are read as 00000000000000. The write value should be 00000000000000.
bits : 2 - 14 (13 bit)
access : read-write
Reserved : These bits are read as 00000000000000. The write value should be 00000000000000.
bits : 2 - 14 (13 bit)
access : read-write
CCRA : GTCCRA Buffer Operation
bits : 16 - 16 (1 bit)
access : read-write
Enumeration:
#00 : 00
Buffer operation is not performed
#01 : 01
Single buffer operation (GTCCRA <--> GTCCRC)
#10 : 10
Double buffer operation (GTCCRA <--> GTCCRC <--> GTCCRD)
#11 : 11
Double buffer operation (GTCCRA <--> GTCCRC <--> GTCCRD)
End of enumeration elements list.
CCRB : GTCCRB Buffer Operation
bits : 18 - 18 (1 bit)
access : read-write
Enumeration:
#00 : 00
Buffer operation is not performed
#01 : 01
Single buffer operation (GTCCRB <--> GTCCRE)
#10 : 10
Double buffer operation (GTCCRB <--> GTCCRE <--> GTCCRF)
#11 : 11
Double buffer operation (GTCCRB <--> GTCCRE <--> GTCCRF)
End of enumeration elements list.
PR : GTPR Buffer Operation
bits : 20 - 20 (1 bit)
access : read-write
Enumeration:
#00 : 00
Buffer operation is not performed
#01 : 01
Single buffer operation (GTPBR --> GTPR)
: others
Setting prohibited
End of enumeration elements list.
CCRSWT : GTCCRA and GTCCRB Forcible Buffer Operation This bit is read as 0.
bits : 22 - 21 (0 bit)
access : write-only
Enumeration:
#0 : 0
no effect
#1 : 1
Forcibly performs buffer transfer of GTCCRA and GTCCRB. This bit automatically returns to 0 after the writing of 1.
End of enumeration elements list.
General PWM Timer Counter
address_offset : 0x48 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
GTCNT : Counter
bits : 0 - 30 (31 bit)
access : read-write
General PWM Timer Compare Capture Register A
address_offset : 0x4C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
GTCCRA : Compare Capture Register A
bits : 0 - 30 (31 bit)
access : read-write
General PWM Timer Compare Capture Register B
address_offset : 0x50 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
GTCCRB : Compare Capture Register B
bits : 0 - 30 (31 bit)
access : read-write
General PWM Timer Compare Capture Register C
address_offset : 0x54 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
GTCCRC : Compare Capture Register C
bits : 0 - 30 (31 bit)
access : read-write
General PWM Timer Compare Capture Register E
address_offset : 0x58 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
GTCCRE : Compare Capture Register E
bits : 0 - 30 (31 bit)
access : read-write
General PWM Timer Compare Capture Register D
address_offset : 0x5C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
GTCCRD : Compare Capture Register D
bits : 0 - 30 (31 bit)
access : read-write
General PWM Timer Compare Capture Register F
address_offset : 0x60 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
GTCCRF : Compare Capture Register F
bits : 0 - 30 (31 bit)
access : read-write
General PWM Timer Cycle Setting Register
address_offset : 0x64 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
GTPR : Cycle Setting Register
bits : 0 - 30 (31 bit)
access : read-write
General PWM Timer Cycle Setting Buffer Register
address_offset : 0x68 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
GTPBR : Cycle Setting Buffer Register
bits : 0 - 30 (31 bit)
access : read-write
General PWM Timer Software Stop Register
address_offset : 0x8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
CSTOP0 : Channel 0 GTCNT Count Stop Read data shows each channel's counter status (GTCR.CST bit). 0 means counter runnning. 1 means counter stop.
bits : 0 - -1 (0 bit)
access : read-write
Enumeration:
#0 : 0
No effect (write) / counter running (read)
#1 : 1
GPT32EH0.GTCNT counter stops (write) / Counter stop (read)
End of enumeration elements list.
CSTOP1 : Channel 1 GTCNT Count Stop Read data shows each channel's counter status (GTCR.CST bit). 0 means counter runnning. 1 means counter stop.
bits : 1 - 0 (0 bit)
access : read-write
Enumeration:
#0 : 0
No effect (write) / counter running (read)
#1 : 1
GPT32EH1.GTCNT counter stops (write) / Counter stop (read)
End of enumeration elements list.
CSTOP2 : Channel 2 GTCNT Count Stop Read data shows each channel's counter status (GTCR.CST bit). 0 means counter runnning. 1 means counter stop.
bits : 2 - 1 (0 bit)
access : read-write
Enumeration:
#0 : 0
No effect (write) / counter running (read)
#1 : 1
GPT32EH2.GTCNT counter stops (write) / Counter stop (read)
End of enumeration elements list.
CSTOP3 : Channel 3 GTCNT Count Stop Read data shows each channel's counter status (GTCR.CST bit). 0 means counter runnning. 1 means counter stop.
bits : 3 - 2 (0 bit)
access : read-write
Enumeration:
#0 : 0
No effect (write) / counter running (read)
#1 : 1
GPT32EH3.GTCNT counter stops (write) / Counter stop (read)
End of enumeration elements list.
CSTOP4 : Channel 4 GTCNT Count Stop Read data shows each channel's counter status (GTCR.CST bit). 0 means counter runnning. 1 means counter stop.
bits : 4 - 3 (0 bit)
access : read-write
Enumeration:
#0 : 0
No effect (write) / counter running (read)
#1 : 1
GPT32E4.GTCNT counter stops (write) / Counter stop (read)
End of enumeration elements list.
CSTOP5 : Channel 5 GTCNT Count Stop Read data shows each channel's counter status (GTCR.CST bit). 0 means counter runnning. 1 means counter stop.
bits : 5 - 4 (0 bit)
access : read-write
Enumeration:
#0 : 0
No effect (write) / counter running (read)
#1 : 1
GPT32E5.GTCNT counter stops (write) / Counter stop (read)
End of enumeration elements list.
CSTOP6 : Channel 6 GTCNT Count Stop Read data shows each channel's counter status (GTCR.CST bit). 0 means counter runnning. 1 means counter stop.
bits : 6 - 5 (0 bit)
access : read-write
Enumeration:
#0 : 0
No effect (write) / counter running (read)
#1 : 1
GPT32E6.GTCNT counter stops (write) / Counter stop (read)
End of enumeration elements list.
CSTOP7 : Channel 7 GTCNT Count Stop Read data shows each channel's counter status (GTCR.CST bit). 0 means counter runnning. 1 means counter stop.
bits : 7 - 6 (0 bit)
access : read-write
Enumeration:
#0 : 0
No effect (write) / counter running (read)
#1 : 1
GPT32E7.GTCNT counter stops (write) / Counter stop (read)
End of enumeration elements list.
CSTOP8 : Channel 8 GTCNT Count Stop Read data shows each channel's counter status (GTCR.CST bit). 0 means counter runnning. 1 means counter stop.
bits : 8 - 7 (0 bit)
access : read-write
Enumeration:
#0 : 0
No effect (write) / counter running (read)
#1 : 1
GPT328.GTCNT counter stops (write) / Counter stop (read)
End of enumeration elements list.
CSTOP9 : Channel 9 GTCNT Count Stop Read data shows each channel's counter status (GTCR.CST bit). 0 means counter runnning. 1 means counter stop.
bits : 9 - 8 (0 bit)
access : read-write
Enumeration:
#0 : 0
No effect (write) / counter running (read)
#1 : 1
GPT329.GTCNT counter stops (write) / Counter stop (read)
End of enumeration elements list.
CSTOP10 : Channel 10 GTCNT Count Stop Read data shows each channel's counter status (GTCR.CST bit). 0 means counter runnning. 1 means counter stop.
bits : 10 - 9 (0 bit)
access : read-write
Enumeration:
#0 : 0
No effect (write) / counter running (read)
#1 : 1
GPT3210.GTCNT counter stops (write) / Counter stop (read)
End of enumeration elements list.
CSTOP11 : Channel 11 GTCNT Count Stop Read data shows each channel's counter status (GTCR.CST bit). 0 means counter runnning. 1 means counter stop.
bits : 11 - 10 (0 bit)
access : read-write
Enumeration:
#0 : 0
No effect (write) / counter running (read)
#1 : 1
GPT3211.GTCNT counter stops (write) / Counter stop (read)
End of enumeration elements list.
CSTOP12 : Channel 12 GTCNT Count Stop Read data shows each channel's counter status (GTCR.CST bit). 0 means counter runnning. 1 means counter stop.
bits : 12 - 11 (0 bit)
access : read-write
Enumeration:
#0 : 0
No effect (write) / counter running (read)
#1 : 1
GPT3212.GTCNT counter stops (write) / Counter stop (read)
End of enumeration elements list.
Reserved : These bits are read as 1111111111111111111. The write value should be 1111111111111111111.
bits : 13 - 30 (18 bit)
access : read-write
General PWM Timer Dead Time Control Register
address_offset : 0x88 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TDE : Negative-Phase Waveform Setting
bits : 0 - -1 (0 bit)
access : read-write
Enumeration:
#0 : 0
Set GTCCRB without using GTDVU and GTDVD.
#1 : 1
Use GTDVU and GTDVD to set the compare match value for negative-phase waveform with automatic dead time in GTCCRB.
End of enumeration elements list.
Reserved : These bits are read as 0000000000000000000000000000000. The write value should be 0000000000000000000000000000000.
bits : 1 - 30 (30 bit)
access : read-write
General PWM Timer Dead Time Value Register U
address_offset : 0x8C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
GTDVU : Dead Time Value Register U
bits : 0 - 30 (31 bit)
access : read-write
General PWM Timer Software Clear Register
address_offset : 0xC Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
CCLR0 : Channel 0 GTCNT Count Clear
bits : 0 - -1 (0 bit)
access : write-only
Enumeration:
#0 : 0
No effect
#1 : 1
GPT32EH0.GTCNT counter clears
End of enumeration elements list.
CCLR1 : Channel 1 GTCNT Count Clear
bits : 1 - 0 (0 bit)
access : write-only
Enumeration:
#0 : 0
No effect
#1 : 1
GPT32EH1.GTCNT counter clears
End of enumeration elements list.
CCLR2 : Channel 2 GTCNT Count Clear
bits : 2 - 1 (0 bit)
access : write-only
Enumeration:
#0 : 0
No effect
#1 : 1
GPT32EH2.GTCNT counter clears
End of enumeration elements list.
CCLR3 : Channel 3 GTCNT Count Clear
bits : 3 - 2 (0 bit)
access : write-only
Enumeration:
#0 : 0
No effect
#1 : 1
GPT32EH3.GTCNT counter clears
End of enumeration elements list.
CCLR4 : Channel 4 GTCNT Count Clear
bits : 4 - 3 (0 bit)
access : write-only
Enumeration:
#0 : 0
No effect
#1 : 1
GPT32E4.GTCNT counter clears
End of enumeration elements list.
CCLR5 : Channel 5 GTCNT Count Clear
bits : 5 - 4 (0 bit)
access : write-only
Enumeration:
#0 : 0
No effect
#1 : 1
GPT32E5.GTCNT counter clears
End of enumeration elements list.
CCLR6 : Channel 6 GTCNT Count Clear
bits : 6 - 5 (0 bit)
access : write-only
Enumeration:
#0 : 0
No effect
#1 : 1
GPT32E6.GTCNT counter clears
End of enumeration elements list.
CCLR7 : Channel 7 GTCNT Count Clear
bits : 7 - 6 (0 bit)
access : write-only
Enumeration:
#0 : 0
No effect
#1 : 1
GPT32E7.GTCNT counter clears
End of enumeration elements list.
CCLR8 : Channel 8 GTCNT Count Clear
bits : 8 - 7 (0 bit)
access : write-only
Enumeration:
#0 : 0
No effect
#1 : 1
GPT328.GTCNT counter clears
End of enumeration elements list.
CCLR9 : Channel 9 GTCNT Count Clear
bits : 9 - 8 (0 bit)
access : write-only
Enumeration:
#0 : 0
No effect
#1 : 1
GPT329.GTCNT counter clears
End of enumeration elements list.
CCLR10 : Channel 10 GTCNT Count Clear
bits : 10 - 9 (0 bit)
access : write-only
Enumeration:
#0 : 0
No effect
#1 : 1
GPT3210.GTCNT counter clears
End of enumeration elements list.
CCLR11 : Channel 11 GTCNT Count Clear
bits : 11 - 10 (0 bit)
access : write-only
Enumeration:
#0 : 0
No effect
#1 : 1
GPT3211.GTCNT counter clears
End of enumeration elements list.
CCLR12 : Channel 12 GTCNT Count Clear
bits : 12 - 11 (0 bit)
access : write-only
Enumeration:
#0 : 0
No effect
#1 : 1
GPT3212.GTCNT counter clears
End of enumeration elements list.
Reserved : The write value should be 1111111111111111111.
bits : 13 - 30 (18 bit)
access : write-only
Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !
This website is sponsored by Embeetle, an IDE designed from scratch for embedded software developers.