PADS_BANK0

Peripheral Memory Blocks

address_offset : 0x0 Bytes (0x0)
size : 0xCC byte (0x0)
mem_usage : registers
protection :

Registers

VOLTAGE_SELECT

GPIO3

GPIO4

GPIO5

GPIO6

GPIO7

GPIO8

GPIO9

GPIO10

GPIO11

GPIO12

GPIO13

GPIO14

GPIO0

GPIO15

GPIO16

GPIO17

GPIO18

GPIO19

GPIO20

GPIO21

GPIO22

GPIO23

GPIO24

GPIO25

GPIO26

GPIO27

GPIO28

GPIO29

GPIO30

GPIO1

GPIO31

GPIO32

GPIO33

GPIO34

GPIO35

GPIO36

GPIO37

GPIO38

GPIO39

GPIO40

GPIO41

GPIO42

GPIO43

GPIO44

GPIO45

GPIO46

GPIO2

GPIO47

SWCLK

SWD


VOLTAGE_SELECT

Voltage select. Per bank control
address_offset : 0x0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

VOLTAGE_SELECT VOLTAGE_SELECT read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 VOLTAGE_SELECT

VOLTAGE_SELECT :
bits : 0 - 0 (1 bit)
access : read-write

Enumeration:

0 : 3v3

Set voltage to 3.3V (DVDD >= 2V5)

1 : 1v8

Set voltage to 1.8V (DVDD <= 1V8)

End of enumeration elements list.


GPIO3


address_offset : 0x10 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO3 GPIO3 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD ISO

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA


1 : 4mA


2 : 8mA


3 : 12mA


End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write

ISO : Pad isolation control. Remove this once the pad is configured by software.
bits : 8 - 8 (1 bit)
access : read-write


GPIO4


address_offset : 0x14 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO4 GPIO4 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD ISO

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA


1 : 4mA


2 : 8mA


3 : 12mA


End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write

ISO : Pad isolation control. Remove this once the pad is configured by software.
bits : 8 - 8 (1 bit)
access : read-write


GPIO5


address_offset : 0x18 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO5 GPIO5 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD ISO

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA


1 : 4mA


2 : 8mA


3 : 12mA


End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write

ISO : Pad isolation control. Remove this once the pad is configured by software.
bits : 8 - 8 (1 bit)
access : read-write


GPIO6


address_offset : 0x1C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO6 GPIO6 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD ISO

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA


1 : 4mA


2 : 8mA


3 : 12mA


End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write

ISO : Pad isolation control. Remove this once the pad is configured by software.
bits : 8 - 8 (1 bit)
access : read-write


GPIO7


address_offset : 0x20 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO7 GPIO7 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD ISO

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA


1 : 4mA


2 : 8mA


3 : 12mA


End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write

ISO : Pad isolation control. Remove this once the pad is configured by software.
bits : 8 - 8 (1 bit)
access : read-write


GPIO8


address_offset : 0x24 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO8 GPIO8 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD ISO

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA


1 : 4mA


2 : 8mA


3 : 12mA


End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write

ISO : Pad isolation control. Remove this once the pad is configured by software.
bits : 8 - 8 (1 bit)
access : read-write


GPIO9


address_offset : 0x28 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO9 GPIO9 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD ISO

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA


1 : 4mA


2 : 8mA


3 : 12mA


End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write

ISO : Pad isolation control. Remove this once the pad is configured by software.
bits : 8 - 8 (1 bit)
access : read-write


GPIO10


address_offset : 0x2C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO10 GPIO10 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD ISO

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA


1 : 4mA


2 : 8mA


3 : 12mA


End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write

ISO : Pad isolation control. Remove this once the pad is configured by software.
bits : 8 - 8 (1 bit)
access : read-write


GPIO11


address_offset : 0x30 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO11 GPIO11 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD ISO

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA


1 : 4mA


2 : 8mA


3 : 12mA


End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write

ISO : Pad isolation control. Remove this once the pad is configured by software.
bits : 8 - 8 (1 bit)
access : read-write


GPIO12


address_offset : 0x34 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO12 GPIO12 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD ISO

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA


1 : 4mA


2 : 8mA


3 : 12mA


End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write

ISO : Pad isolation control. Remove this once the pad is configured by software.
bits : 8 - 8 (1 bit)
access : read-write


GPIO13


address_offset : 0x38 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO13 GPIO13 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD ISO

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA


1 : 4mA


2 : 8mA


3 : 12mA


End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write

ISO : Pad isolation control. Remove this once the pad is configured by software.
bits : 8 - 8 (1 bit)
access : read-write


GPIO14


address_offset : 0x3C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO14 GPIO14 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD ISO

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA


1 : 4mA


2 : 8mA


3 : 12mA


End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write

ISO : Pad isolation control. Remove this once the pad is configured by software.
bits : 8 - 8 (1 bit)
access : read-write


GPIO0


address_offset : 0x4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO0 GPIO0 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD ISO

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA


1 : 4mA


2 : 8mA


3 : 12mA


End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write

ISO : Pad isolation control. Remove this once the pad is configured by software.
bits : 8 - 8 (1 bit)
access : read-write


GPIO15


address_offset : 0x40 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO15 GPIO15 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD ISO

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA


1 : 4mA


2 : 8mA


3 : 12mA


End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write

ISO : Pad isolation control. Remove this once the pad is configured by software.
bits : 8 - 8 (1 bit)
access : read-write


GPIO16


address_offset : 0x44 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO16 GPIO16 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD ISO

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA


1 : 4mA


2 : 8mA


3 : 12mA


End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write

ISO : Pad isolation control. Remove this once the pad is configured by software.
bits : 8 - 8 (1 bit)
access : read-write


GPIO17


address_offset : 0x48 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO17 GPIO17 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD ISO

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA


1 : 4mA


2 : 8mA


3 : 12mA


End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write

ISO : Pad isolation control. Remove this once the pad is configured by software.
bits : 8 - 8 (1 bit)
access : read-write


GPIO18


address_offset : 0x4C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO18 GPIO18 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD ISO

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA


1 : 4mA


2 : 8mA


3 : 12mA


End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write

ISO : Pad isolation control. Remove this once the pad is configured by software.
bits : 8 - 8 (1 bit)
access : read-write


GPIO19


address_offset : 0x50 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO19 GPIO19 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD ISO

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA


1 : 4mA


2 : 8mA


3 : 12mA


End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write

ISO : Pad isolation control. Remove this once the pad is configured by software.
bits : 8 - 8 (1 bit)
access : read-write


GPIO20


address_offset : 0x54 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO20 GPIO20 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD ISO

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA


1 : 4mA


2 : 8mA


3 : 12mA


End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write

ISO : Pad isolation control. Remove this once the pad is configured by software.
bits : 8 - 8 (1 bit)
access : read-write


GPIO21


address_offset : 0x58 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO21 GPIO21 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD ISO

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA


1 : 4mA


2 : 8mA


3 : 12mA


End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write

ISO : Pad isolation control. Remove this once the pad is configured by software.
bits : 8 - 8 (1 bit)
access : read-write


GPIO22


address_offset : 0x5C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO22 GPIO22 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD ISO

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA


1 : 4mA


2 : 8mA


3 : 12mA


End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write

ISO : Pad isolation control. Remove this once the pad is configured by software.
bits : 8 - 8 (1 bit)
access : read-write


GPIO23


address_offset : 0x60 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO23 GPIO23 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD ISO

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA


1 : 4mA


2 : 8mA


3 : 12mA


End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write

ISO : Pad isolation control. Remove this once the pad is configured by software.
bits : 8 - 8 (1 bit)
access : read-write


GPIO24


address_offset : 0x64 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO24 GPIO24 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD ISO

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA


1 : 4mA


2 : 8mA


3 : 12mA


End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write

ISO : Pad isolation control. Remove this once the pad is configured by software.
bits : 8 - 8 (1 bit)
access : read-write


GPIO25


address_offset : 0x68 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO25 GPIO25 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD ISO

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA


1 : 4mA


2 : 8mA


3 : 12mA


End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write

ISO : Pad isolation control. Remove this once the pad is configured by software.
bits : 8 - 8 (1 bit)
access : read-write


GPIO26


address_offset : 0x6C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO26 GPIO26 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD ISO

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA


1 : 4mA


2 : 8mA


3 : 12mA


End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write

ISO : Pad isolation control. Remove this once the pad is configured by software.
bits : 8 - 8 (1 bit)
access : read-write


GPIO27


address_offset : 0x70 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO27 GPIO27 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD ISO

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA


1 : 4mA


2 : 8mA


3 : 12mA


End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write

ISO : Pad isolation control. Remove this once the pad is configured by software.
bits : 8 - 8 (1 bit)
access : read-write


GPIO28


address_offset : 0x74 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO28 GPIO28 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD ISO

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA


1 : 4mA


2 : 8mA


3 : 12mA


End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write

ISO : Pad isolation control. Remove this once the pad is configured by software.
bits : 8 - 8 (1 bit)
access : read-write


GPIO29


address_offset : 0x78 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO29 GPIO29 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD ISO

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA


1 : 4mA


2 : 8mA


3 : 12mA


End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write

ISO : Pad isolation control. Remove this once the pad is configured by software.
bits : 8 - 8 (1 bit)
access : read-write


GPIO30


address_offset : 0x7C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO30 GPIO30 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD ISO

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA


1 : 4mA


2 : 8mA


3 : 12mA


End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write

ISO : Pad isolation control. Remove this once the pad is configured by software.
bits : 8 - 8 (1 bit)
access : read-write


GPIO1


address_offset : 0x8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO1 GPIO1 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD ISO

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA


1 : 4mA


2 : 8mA


3 : 12mA


End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write

ISO : Pad isolation control. Remove this once the pad is configured by software.
bits : 8 - 8 (1 bit)
access : read-write


GPIO31


address_offset : 0x80 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO31 GPIO31 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD ISO

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA


1 : 4mA


2 : 8mA


3 : 12mA


End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write

ISO : Pad isolation control. Remove this once the pad is configured by software.
bits : 8 - 8 (1 bit)
access : read-write


GPIO32


address_offset : 0x84 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO32 GPIO32 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD ISO

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA


1 : 4mA


2 : 8mA


3 : 12mA


End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write

ISO : Pad isolation control. Remove this once the pad is configured by software.
bits : 8 - 8 (1 bit)
access : read-write


GPIO33


address_offset : 0x88 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO33 GPIO33 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD ISO

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA


1 : 4mA


2 : 8mA


3 : 12mA


End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write

ISO : Pad isolation control. Remove this once the pad is configured by software.
bits : 8 - 8 (1 bit)
access : read-write


GPIO34


address_offset : 0x8C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO34 GPIO34 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD ISO

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA


1 : 4mA


2 : 8mA


3 : 12mA


End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write

ISO : Pad isolation control. Remove this once the pad is configured by software.
bits : 8 - 8 (1 bit)
access : read-write


GPIO35


address_offset : 0x90 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO35 GPIO35 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD ISO

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA


1 : 4mA


2 : 8mA


3 : 12mA


End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write

ISO : Pad isolation control. Remove this once the pad is configured by software.
bits : 8 - 8 (1 bit)
access : read-write


GPIO36


address_offset : 0x94 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO36 GPIO36 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD ISO

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA


1 : 4mA


2 : 8mA


3 : 12mA


End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write

ISO : Pad isolation control. Remove this once the pad is configured by software.
bits : 8 - 8 (1 bit)
access : read-write


GPIO37


address_offset : 0x98 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO37 GPIO37 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD ISO

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA


1 : 4mA


2 : 8mA


3 : 12mA


End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write

ISO : Pad isolation control. Remove this once the pad is configured by software.
bits : 8 - 8 (1 bit)
access : read-write


GPIO38


address_offset : 0x9C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO38 GPIO38 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD ISO

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA


1 : 4mA


2 : 8mA


3 : 12mA


End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write

ISO : Pad isolation control. Remove this once the pad is configured by software.
bits : 8 - 8 (1 bit)
access : read-write


GPIO39


address_offset : 0xA0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO39 GPIO39 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD ISO

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA


1 : 4mA


2 : 8mA


3 : 12mA


End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write

ISO : Pad isolation control. Remove this once the pad is configured by software.
bits : 8 - 8 (1 bit)
access : read-write


GPIO40


address_offset : 0xA4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO40 GPIO40 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD ISO

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA


1 : 4mA


2 : 8mA


3 : 12mA


End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write

ISO : Pad isolation control. Remove this once the pad is configured by software.
bits : 8 - 8 (1 bit)
access : read-write


GPIO41


address_offset : 0xA8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO41 GPIO41 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD ISO

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA


1 : 4mA


2 : 8mA


3 : 12mA


End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write

ISO : Pad isolation control. Remove this once the pad is configured by software.
bits : 8 - 8 (1 bit)
access : read-write


GPIO42


address_offset : 0xAC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO42 GPIO42 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD ISO

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA


1 : 4mA


2 : 8mA


3 : 12mA


End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write

ISO : Pad isolation control. Remove this once the pad is configured by software.
bits : 8 - 8 (1 bit)
access : read-write


GPIO43


address_offset : 0xB0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO43 GPIO43 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD ISO

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA


1 : 4mA


2 : 8mA


3 : 12mA


End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write

ISO : Pad isolation control. Remove this once the pad is configured by software.
bits : 8 - 8 (1 bit)
access : read-write


GPIO44


address_offset : 0xB4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO44 GPIO44 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD ISO

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA


1 : 4mA


2 : 8mA


3 : 12mA


End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write

ISO : Pad isolation control. Remove this once the pad is configured by software.
bits : 8 - 8 (1 bit)
access : read-write


GPIO45


address_offset : 0xB8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO45 GPIO45 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD ISO

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA


1 : 4mA


2 : 8mA


3 : 12mA


End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write

ISO : Pad isolation control. Remove this once the pad is configured by software.
bits : 8 - 8 (1 bit)
access : read-write


GPIO46


address_offset : 0xBC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO46 GPIO46 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD ISO

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA


1 : 4mA


2 : 8mA


3 : 12mA


End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write

ISO : Pad isolation control. Remove this once the pad is configured by software.
bits : 8 - 8 (1 bit)
access : read-write


GPIO2


address_offset : 0xC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO2 GPIO2 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD ISO

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA


1 : 4mA


2 : 8mA


3 : 12mA


End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write

ISO : Pad isolation control. Remove this once the pad is configured by software.
bits : 8 - 8 (1 bit)
access : read-write


GPIO47


address_offset : 0xC0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO47 GPIO47 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD ISO

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA


1 : 4mA


2 : 8mA


3 : 12mA


End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write

ISO : Pad isolation control. Remove this once the pad is configured by software.
bits : 8 - 8 (1 bit)
access : read-write


SWCLK


address_offset : 0xC4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

SWCLK SWCLK read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD ISO

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA


1 : 4mA


2 : 8mA


3 : 12mA


End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write

ISO : Pad isolation control. Remove this once the pad is configured by software.
bits : 8 - 8 (1 bit)
access : read-write


SWD


address_offset : 0xC8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

SWD SWD read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD ISO

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA


1 : 4mA


2 : 8mA


3 : 12mA


End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write

ISO : Pad isolation control. Remove this once the pad is configured by software.
bits : 8 - 8 (1 bit)
access : read-write



Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !

This website is sponsored by EmbeetleEmbeetle, an IDE designed from scratch for embedded software developers.