\n

PWR

Peripheral Memory Blocks

address_offset : 0x0 Bytes (0x0)
size : 0x400 byte (0x0)
mem_usage : registers
protection : not protected

Registers

CR

CSR


CR

power control register
address_offset : 0x0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

CR CR read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 LPDS PDDS CWUF CSBF PVDE PLS DBP FPDS

LPDS : Low-power deep sleep
bits : 0 - 0 (1 bit)

PDDS : Power down deepsleep
bits : 1 - 1 (1 bit)

CWUF : Clear wakeup flag
bits : 2 - 2 (1 bit)

CSBF : Clear standby flag
bits : 3 - 3 (1 bit)

PVDE : Power voltage detector enable
bits : 4 - 4 (1 bit)

PLS : PVD level selection
bits : 5 - 7 (3 bit)

DBP : Disable backup domain write protection
bits : 8 - 8 (1 bit)

FPDS : Flash power down in Stop mode
bits : 9 - 9 (1 bit)


CSR

power control/status register
address_offset : 0x4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

CSR CSR read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 WUF SBF PVDO BRR VREFINTRDY EWUP EWUP1 BRE EWUP2 EWUP3 EWUP4 EWUP5 EWUP6 EWUP7 EWUP8

WUF : Wakeup flag
bits : 0 - 0 (1 bit)
access : read-only

SBF : Standby flag
bits : 1 - 1 (1 bit)
access : read-only

PVDO : PVD output
bits : 2 - 2 (1 bit)
access : read-only

BRR : Backup regulator ready
bits : 3 - 3 (1 bit)
access : read-only

VREFINTRDY : VREFINT reference voltage ready
bits : 3 - 3 (1 bit)
access : read-only

EWUP : Enable WKUP pin
bits : 8 - 8 (1 bit)
access : read-write

EWUP1 : Enable WKUP pin 1
bits : 8 - 8 (1 bit)
access : read-write

BRE : Backup regulator enable
bits : 9 - 9 (1 bit)
access : read-write

EWUP2 : Enable WKUP pin 2
bits : 9 - 9 (1 bit)
access : read-write

EWUP3 : Enable WKUP pin 3
bits : 10 - 10 (1 bit)
access : read-write

EWUP4 : Enable WKUP pin 4
bits : 11 - 11 (1 bit)
access : read-write

EWUP5 : Enable WKUP pin 5
bits : 12 - 12 (1 bit)
access : read-write

EWUP6 : Enable WKUP pin 6
bits : 13 - 13 (1 bit)
access : read-write

EWUP7 : Enable WKUP pin 7
bits : 14 - 14 (1 bit)
access : read-write

EWUP8 : Enable WKUP pin 8
bits : 15 - 15 (1 bit)
access : read-write



Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !

This website is sponsored by EmbeetleEmbeetle, an IDE designed from scratch for embedded software developers.