\n

PADS_BANK0

Peripheral Memory Blocks

address_offset : 0x0 Bytes (0x0)
size : 0x1000 byte (0x0)
mem_usage : registers
protection : not protected

Registers

VOLTAGE_SELECT

GPIO3

GPIO4

GPIO5

GPIO6

GPIO7

GPIO8

GPIO9

GPIO10

GPIO11

GPIO12

GPIO13

GPIO14

GPIO0

GPIO15

GPIO16

GPIO17

GPIO18

GPIO19

GPIO20

GPIO21

GPIO22

GPIO23

GPIO24

GPIO25

GPIO26

GPIO27

GPIO28

GPIO29

SWCLK

GPIO1

SWD

GPIO2


VOLTAGE_SELECT

Voltage select. Per bank control
address_offset : 0x0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

VOLTAGE_SELECT VOLTAGE_SELECT read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 VOLTAGE_SELECT

VOLTAGE_SELECT :
bits : 0 - 0 (1 bit)
access : read-write

Enumeration:

0 : 3v3

Set voltage to 3.3V (DVDD >= 2V5)

1 : 1v8

Set voltage to 1.8V (DVDD <= 1V8)

End of enumeration elements list.


GPIO3

Pad control register
address_offset : 0x10 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO3 GPIO3 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA

None

1 : 4mA

None

2 : 8mA

None

3 : 12mA

None

End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write


GPIO4

Pad control register
address_offset : 0x14 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO4 GPIO4 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA

None

1 : 4mA

None

2 : 8mA

None

3 : 12mA

None

End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write


GPIO5

Pad control register
address_offset : 0x18 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO5 GPIO5 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA

None

1 : 4mA

None

2 : 8mA

None

3 : 12mA

None

End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write


GPIO6

Pad control register
address_offset : 0x1C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO6 GPIO6 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA

None

1 : 4mA

None

2 : 8mA

None

3 : 12mA

None

End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write


GPIO7

Pad control register
address_offset : 0x20 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO7 GPIO7 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA

None

1 : 4mA

None

2 : 8mA

None

3 : 12mA

None

End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write


GPIO8

Pad control register
address_offset : 0x24 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO8 GPIO8 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA

None

1 : 4mA

None

2 : 8mA

None

3 : 12mA

None

End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write


GPIO9

Pad control register
address_offset : 0x28 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO9 GPIO9 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA

None

1 : 4mA

None

2 : 8mA

None

3 : 12mA

None

End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write


GPIO10

Pad control register
address_offset : 0x2C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO10 GPIO10 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA

None

1 : 4mA

None

2 : 8mA

None

3 : 12mA

None

End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write


GPIO11

Pad control register
address_offset : 0x30 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO11 GPIO11 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA

None

1 : 4mA

None

2 : 8mA

None

3 : 12mA

None

End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write


GPIO12

Pad control register
address_offset : 0x34 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO12 GPIO12 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA

None

1 : 4mA

None

2 : 8mA

None

3 : 12mA

None

End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write


GPIO13

Pad control register
address_offset : 0x38 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO13 GPIO13 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA

None

1 : 4mA

None

2 : 8mA

None

3 : 12mA

None

End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write


GPIO14

Pad control register
address_offset : 0x3C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO14 GPIO14 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA

None

1 : 4mA

None

2 : 8mA

None

3 : 12mA

None

End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write


GPIO0

Pad control register
address_offset : 0x4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO0 GPIO0 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA

None

1 : 4mA

None

2 : 8mA

None

3 : 12mA

None

End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write


GPIO15

Pad control register
address_offset : 0x40 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO15 GPIO15 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA

None

1 : 4mA

None

2 : 8mA

None

3 : 12mA

None

End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write


GPIO16

Pad control register
address_offset : 0x44 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO16 GPIO16 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA

None

1 : 4mA

None

2 : 8mA

None

3 : 12mA

None

End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write


GPIO17

Pad control register
address_offset : 0x48 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO17 GPIO17 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA

None

1 : 4mA

None

2 : 8mA

None

3 : 12mA

None

End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write


GPIO18

Pad control register
address_offset : 0x4C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO18 GPIO18 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA

None

1 : 4mA

None

2 : 8mA

None

3 : 12mA

None

End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write


GPIO19

Pad control register
address_offset : 0x50 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO19 GPIO19 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA

None

1 : 4mA

None

2 : 8mA

None

3 : 12mA

None

End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write


GPIO20

Pad control register
address_offset : 0x54 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO20 GPIO20 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA

None

1 : 4mA

None

2 : 8mA

None

3 : 12mA

None

End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write


GPIO21

Pad control register
address_offset : 0x58 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO21 GPIO21 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA

None

1 : 4mA

None

2 : 8mA

None

3 : 12mA

None

End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write


GPIO22

Pad control register
address_offset : 0x5C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO22 GPIO22 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA

None

1 : 4mA

None

2 : 8mA

None

3 : 12mA

None

End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write


GPIO23

Pad control register
address_offset : 0x60 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO23 GPIO23 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA

None

1 : 4mA

None

2 : 8mA

None

3 : 12mA

None

End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write


GPIO24

Pad control register
address_offset : 0x64 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO24 GPIO24 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA

None

1 : 4mA

None

2 : 8mA

None

3 : 12mA

None

End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write


GPIO25

Pad control register
address_offset : 0x68 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO25 GPIO25 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA

None

1 : 4mA

None

2 : 8mA

None

3 : 12mA

None

End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write


GPIO26

Pad control register
address_offset : 0x6C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO26 GPIO26 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA

None

1 : 4mA

None

2 : 8mA

None

3 : 12mA

None

End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write


GPIO27

Pad control register
address_offset : 0x70 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO27 GPIO27 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA

None

1 : 4mA

None

2 : 8mA

None

3 : 12mA

None

End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write


GPIO28

Pad control register
address_offset : 0x74 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO28 GPIO28 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA

None

1 : 4mA

None

2 : 8mA

None

3 : 12mA

None

End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write


GPIO29

Pad control register
address_offset : 0x78 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO29 GPIO29 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA

None

1 : 4mA

None

2 : 8mA

None

3 : 12mA

None

End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write


SWCLK

Pad control register
address_offset : 0x7C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

SWCLK SWCLK read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA

None

1 : 4mA

None

2 : 8mA

None

3 : 12mA

None

End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write


GPIO1

Pad control register
address_offset : 0x8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO1 GPIO1 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA

None

1 : 4mA

None

2 : 8mA

None

3 : 12mA

None

End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write


SWD

Pad control register
address_offset : 0x80 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

SWD SWD read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA

None

1 : 4mA

None

2 : 8mA

None

3 : 12mA

None

End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write


GPIO2

Pad control register
address_offset : 0xC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO2 GPIO2 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA

None

1 : 4mA

None

2 : 8mA

None

3 : 12mA

None

End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write



Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !

This website is sponsored by EmbeetleEmbeetle, an IDE designed from scratch for embedded software developers.