\n

PADS_QSPI

Peripheral Memory Blocks

address_offset : 0x0 Bytes (0x0)
size : 0x1000 byte (0x0)
mem_usage : registers
protection : not protected

Registers

VOLTAGE_SELECT

GPIO_QSPI_SD2

GPIO_QSPI_SD3

GPIO_QSPI_SS

GPIO_QSPI_SCLK

GPIO_QSPI_SD0

GPIO_QSPI_SD1


VOLTAGE_SELECT

Voltage select. Per bank control
address_offset : 0x0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

VOLTAGE_SELECT VOLTAGE_SELECT read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 VOLTAGE_SELECT

VOLTAGE_SELECT :
bits : 0 - 0 (1 bit)
access : read-write

Enumeration:

0 : 3v3

Set voltage to 3.3V (DVDD >= 2V5)

1 : 1v8

Set voltage to 1.8V (DVDD <= 1V8)

End of enumeration elements list.


GPIO_QSPI_SD2

Pad control register
address_offset : 0x10 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO_QSPI_SD2 GPIO_QSPI_SD2 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA

None

1 : 4mA

None

2 : 8mA

None

3 : 12mA

None

End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write


GPIO_QSPI_SD3

Pad control register
address_offset : 0x14 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO_QSPI_SD3 GPIO_QSPI_SD3 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA

None

1 : 4mA

None

2 : 8mA

None

3 : 12mA

None

End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write


GPIO_QSPI_SS

Pad control register
address_offset : 0x18 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO_QSPI_SS GPIO_QSPI_SS read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA

None

1 : 4mA

None

2 : 8mA

None

3 : 12mA

None

End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write


GPIO_QSPI_SCLK

Pad control register
address_offset : 0x4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO_QSPI_SCLK GPIO_QSPI_SCLK read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA

None

1 : 4mA

None

2 : 8mA

None

3 : 12mA

None

End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write


GPIO_QSPI_SD0

Pad control register
address_offset : 0x8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO_QSPI_SD0 GPIO_QSPI_SD0 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA

None

1 : 4mA

None

2 : 8mA

None

3 : 12mA

None

End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write


GPIO_QSPI_SD1

Pad control register
address_offset : 0xC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

GPIO_QSPI_SD1 GPIO_QSPI_SD1 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 SLEWFAST SCHMITT PDE PUE DRIVE IE OD

SLEWFAST : Slew rate control. 1 = Fast, 0 = Slow
bits : 0 - 0 (1 bit)
access : read-write

SCHMITT : Enable schmitt trigger
bits : 1 - 1 (1 bit)
access : read-write

PDE : Pull down enable
bits : 2 - 2 (1 bit)
access : read-write

PUE : Pull up enable
bits : 3 - 3 (1 bit)
access : read-write

DRIVE : Drive strength.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0 : 2mA

None

1 : 4mA

None

2 : 8mA

None

3 : 12mA

None

End of enumeration elements list.

IE : Input enable
bits : 6 - 6 (1 bit)
access : read-write

OD : Output disable. Has priority over output enable from peripherals
bits : 7 - 7 (1 bit)
access : read-write



Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !

This website is sponsored by EmbeetleEmbeetle, an IDE designed from scratch for embedded software developers.