Embeetle, an IDE designed from scratch for embedded software developers.address_offset : 0x0 Bytes (0x0)
size : 0x10 byte (0x0)
mem_usage : registers
protection : not protected
ACMP1 Configuration Register 0
address_offset : 0x0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MOD : ACMP1 sensitivity modes of the interrupt trigger
bits : 0 - 1 (2 bit)
access : read-write
Enumeration:
#00 : 00
ACMP1 interrupt on output falling edge.
#01 : 01
ACMP1 interrupt on output rising edge.
#10 : 10
ACMP1 interrupt on output falling edge.
#11 : 11
ACMP1 interrupt on output falling or rising edge.
End of enumeration elements list.
IE : ACMP1 Interrupt Enable
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disable the ACMP1 Interrupt.
#1 : 1
Enable the ACMP1 Interrupt.
End of enumeration elements list.
HYST : Analog Comparator Hysterisis Selection
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
20 mV.
#1 : 1
30 mV.
End of enumeration elements list.
EN : Analog Comparator Enable
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
The ACMP1 is disabled.
#1 : 1
The ACMP1 is enabled.
End of enumeration elements list.
ACMP1 Configuration Register 1
address_offset : 0x4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
NSEL : ACMP1 Negative Input Select
bits : 0 - 2 (3 bit)
access : read-write
Enumeration:
#000 : 000
External input 0
#001 : 001
External input 1
#010 : 010
External input 2
#011 : 011
External input 3
#100 : 100
External input 4
#101 : 101
DAC1 Output
#110 : 110
ACMP1 output tie 0
#111 : 111
ACMP1 output tie 0
End of enumeration elements list.
PSEL : ACMP1 Positive Input Select
bits : 4 - 6 (3 bit)
access : read-write
Enumeration:
#000 : 000
External input 0
#001 : 001
External input 1
#010 : 010
External input 2
#011 : 011
External input 3
#100 : 100
External input 4
#101 : 101
DAC1 Output
#110 : 110
ACMP1 output tie 0
#111 : 111
ACMP1 output tie 0
End of enumeration elements list.
ACMP1 configuration register 2
address_offset : 0x8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
VAL : DAC1 Output Level Selection
bits : 0 - 5 (6 bit)
access : read-write
DACEN : DAC1 Enable
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
The DAC1 is disabled.
#1 : 1
The DAC1 is enabled.
End of enumeration elements list.
ACMP0 data output register 0
address_offset : 0xC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
O : ACMP1 output
bits : 0 - 0 (1 bit)
access : read-write
F : ACMP1 interrupt Flag
bits : 4 - 4 (1 bit)
access : read-write
WUF : ACMP1 low power wakeup interrupt flag
bits : 6 - 6 (1 bit)
access : read-write
Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !
This website is sponsored by Embeetle, an IDE designed from scratch for embedded software developers.